Fuji IP-10 Digital Passport System: Quick Reference Guide

Transcription

1

2 1. Make sure the ink ribbon cartridge is free of slack. Place it in the right side of the printer & close the door. Be sure to slide it in as per the directional arrow on the cartridge. 2. Slide the top of the paper tray about 1/2 forward, so that the lid can rotate up. 3. Load the paper into the tray with the glossy side up. 4. Close the lid, but do not slide the top back into its original position. 5. Slide the paper tray into the slot on the front of the printer. 6. Plug the power cord and the USB extension cable into the printer. It should power on and start up by itself. If not press the large, domed power button. 7. Connect the camera USB cable to the extension, then plug the smaller end into the side of the camera. 8. Power on the camera & press the MENU/OK button in the center of the round cursor controls. 9. Press the cursor down ring to select QUALITY. Press MENU/OK to change the setting.

3 10. Select 2M and press MENU/OK again to confirm. 11. Using the printer s navigation cursor ring/buttons, press down to select ID SETTING. 12. Press MENU/OK to open setting. 13. Press down to select CAMERA DIRECT ID. Press MENU/OK to open setting. 14. Select EASY OPERATION A to auto print ALL photos stored in the camera. Choose EASY OPERATION B to be able to select which photos will be printed. Press MENU/OK to confirm. 15. For the size/layout select the 51mm X 51mm X2 option and press MENU/OK to confirm. 16. If prompted, choose whether to delete photos from camera upon printing - or to leave them stored in the camera. Press MENU/OK to confirm. 17. At the MAIN MENU, select the CAMERA DIRECT ID EASY A (or B) and press MENU/OK to confirm. 18. The EASY-A mode will tell you to take your images, then with the camera plugged into the printer, press the PRINT button. This will automatically print all images stored on the camera.

4 19. The EASY-B mode will tell you to take your images, then with the camera plugged into the printer, press the MENU/OK button. This allows you to select which images you want to print. 20. Make sure you are shooting on a flat surface that is colored white or evern very light gray and that it is non-reflective. 21. Position the subject, sitting upright, directly in front of the background. Place the camera about 4 feet from the subject. 22. Use the zoom controls to make the top of the head and the chin fill up and touch the edges of the onscreen shooting guide outline. Press the exposure button to take the picture. 23. You may need to use the flash to ensure as little shadow behind the person as possible. 24. Ensure the camera is plugged into the printer. Press the PRINT button if using EASY-A mode. The printer downloads the photos & begins to make the prints. Do not disturb the paper tray. 25. Make sure there is AT LEAST 8 inches of clearance behind the printer. Each sheet takes about 90 seconds to print. When done, you ll have 2 identical photos, ready for you to trim them down to 2 x If using the EASY-B mode: press the MENU/OK button to download images to the printer. Use the cursor right or left arrows to choose the image that you want to print. 27. Press the MENU/OK to select. Next you ll see a proof of how your print will look. Press the PRINT button to begin printing.

5 28. Bend the leader strips at the perforations to cleanly tear them off of each side of the sheet. 29. Insert the sheet into a Passport Photo Cutter and align the photo within the square opening. 30. Once in position, press down on the lever to activate the cutter. 31. Flip the sheet over and repeat the alignment of the remaining photo. Once positioned, press the lever down to make the cut. 32. Place the finished 2 x 2 photos in a Passport Folder to protect and keep them free of finger prints. 24. Close the front tab top create a professional presentation for your customers.