Important. Specifications / Functions. Table of Contents. ASSA ABLOY, the global leader in door opening solutions.

Size: px

Start display at page:

Download "Important. Specifications / Functions. Table of Contents. ASSA ABLOY, the global leader in door opening solutions."

Cornelius Willis Jones
7 years ago
Views:

1 SARGENT Wiring Instructions for Ecoflex Electrified Mortise Locks* (7970,7,7,73 & 870,7,7,73) for -4 Volts and Mechanical Mortise Locks with Monitoring Prefixes (RX, LX & DX) with the ElectroLynx Connector System For assistance, contact SARGENT at WIRE (9473) or w Important CAUTION: The voltage applied to the lock actuator must not exceed 0% of rated voltage. If the voltage exceeds this value, the actuator may be damaged. Specifications / Functions Ecoflex Actuator Fail Safe Models: 7970, 797, 870 and 87 (each /4 volts) /4 volts) RX-, LX-, and DX- Lock es AMP 4VDC RX- (lever monitor switches) LX- (latch monitor switch): *Patent Pending DX- (deadbolt monitor switch): Table of Contents Important/CAUTION Specifications/Functions Installation Notes Installing And Wiring Ecoflex Electrified Mortise Locks 7900 & 800 Series RX-7900 & RX-800 Series RX-LX-800 Series LX-800 Series Installing And Wiring Mechanical Mortise Locks With Monitoring RX-7900 & RX-800 Series RX-LX-800 Series RX-DX-800 Series LX-800 Series DX-800 Series Copyright 04, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. A77D

2 two- IMPORTANT: to Actuator only LX / DX Actuator Fail Secure Check Polarity: Verify + (red) wire LX Fail Secure Fail Safe DX Fail Safe *Patent Pending Installation Notes. Install mortise lock and electric hinge. With new applications, a raceway harness will be pre-installed inside the door by ASSA ABLOY door manufacturer when specified during ordering process. kits are also available for retrofit applications.. If door does not have a raceway harness with, either consult factory for raceway retrofit kit or cut the off product and hardwire, as required. 3. Wiring to pigtail harness is per facility wiring requirement. Follow individual instructions below. ElectroLynx Connector System Notes The system is designed to be installation friendly with from the electric hinge through the door to the lock. The only wiring is to the harness which plugs into the electric hinge. IMPORTANT: The plug and receptacle are designed to mate and lock together as shown in the illustration. Plug the into each other with the locking mechanism aligned as indicated. Do NOT force on any other way. 8-Pin Connector Locking mechanism Look for the LYNX Plug Receptacle ElectroLynx As part of their promise to provide innovative, fast and effective, and higher security solutions to their customers, ASSA ABLOY Group companies offer ElectroLynx, a universal quick-connect system that simplifies the electrification of the door opening. ElectroLynx is a registered trademark of ASSA ABLOY, Inc. A77D Copyright 04, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.

3 Ecoflex installation Red (+), Black (-), Pigtail harness ( wires with an 8-pin connector) Red (+), Black (-), Electrified mortise lock with 8-pin connector Plug together Black (-) Red (+) ( wires with an 8-pin connector) connector. 4-pin are not used here. A VDC.0 AMP Regulated and Filtered Power Supply Input L N 0VAC 60HZ 0VAC L/N/G GND Output Output 4VDC Normally Closed Fire Alarm Contact (If Required) C * or relay contacts NO NC Pigtail harness ( wires with 8-pin connector) Red (+), Black (-), * Note: Wire 7970/870 or 797/87 (Fail Safe) Locks to switch as shown. For 797/87 or 7973/873 (Fail Secure) Locks wire switch NO (normally open) contact to red wire of pigtail harness. Plug into 8-pin hinge connector at door (8 Volt) Fail Safe actuator with a 0/4VAC transformer LINE NORMALLY CLOSED FIRE ALARM CONTACT (IF REQUIRED) C NO NC Red (+), Black (-), ELECTROLYNX CONNECTORS Electromechanical Mortise Lock 0 VAC 4VAC Pigtail Harness wire with 8 pin connector Red (+) Black (-) NEUTRAL actuator Copyright 04, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. A77D

4 Ecoflex RX- (7900 & 800 locks) The RX-switches are in the latch is extended. RX-switches monitor inside and Solenoid White (C), 3 Red (+), Black (-), Pigtail harness with 8-pin connector with 8 wires with 8-pin with 8 wires 8 wires Note: V Lock has Red Heat Shrink 4V Lock has Black Heat Shrink RX-7970, 7, 7 or 73 or RX-870, 7, 7 or 73 lock with 8-pin connector connector. 4-pin are not used here. Ecoflex RX- and LX- wiring (800 locks only) The RX-switches are in the latch is extended. RX- switches monitor inside and Solenoid White (C), 3 Red (+), Black (-), LX- switch monitors latchbolt movement Pigtail harnesses with 8&4-pin with 8 & 4-pin 8 wires LX- wiring (3 wires) RX-LX-870,7,7 or 73 lock with 8 & 4-pin LX - The LX- switch is in the the latch is extended., 4, 3, A77D Copyright 04, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.

5 Actuator with LX- wiring (800 locks only) LX- switch monitors latchbolt retraction LX - Solenoid The LX-switch is in the the latch is extended Adaptor Harness (8 & 4-pin to 6 wires and 8-pin connector). Plug in between lock and raceway harness. Blue (NC), 6 Orange (NO), 5 Green (C), 4 Red (+), Black (-), with 8-pin connector Pigtail Harness with 8-pin connector Actuator wiring ( wires) Red (+) Black (-) LX- wiring (3 wires) connector. 4-pin are not used here. LX-870,7,7 or 73 lock with 8 & 4-pin RX- wiring (7900 & 800 locks) RX- switches monitor inside and RX- wiring (6 wires) 6 wires RX-7900 or RX-800 series lock with 8-pin connector White (C), 3 The RX-switches are in the latch is extended. with 8-pin Pigtail harness with 8-pin connector connector. 4-pin are not used here. Copyright 04, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. A77D 5

6 RX- LX- wiring (800 locks only) RX- switches monitor inside and RX- wiring (6 wires) 6wires LX- wiring (3 wires) RX-LX-800 series lock with 8 & 4-pin LX- Pigtail harnesses with 8 & 4-pin LX - The RX-switches ar e in the, 4, 3, 4 3 The LX-switch is in the RX- DX- wiring (800 locks only) The RX-switches ar e in the RX- switches monitor inside and RX-wiring (6 wires) 6wires DX-wiring (3 wires) RX-DX-800 series lock with 8 & 4-pin DX- Pigtail harnesses with 8&4-pin DX- The DX-switch is in the, 4, 3, A77D Copyright 04, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.

Transfer Device Solutions

Transfer Device Solutions McKINNEY QC hinge transfers power from the power supply to the exit device Electromechanical exit device with ElectroLynx 3" cable, minimum, needed between electromechanical exit and QC hinge Contents