INSTALLATION INSTRUCTIONS

Transcription

1 INSTALLATION INSTRUCTIONS Accessory ROOF RACK RAILS P/N 08L02-T0A-110 Application 2014 CR-V Publications No. AII Issue Date JULY 2013 PARTS LIST Left roof rack rail Right roof rack rail Cap A, left TOOLS AND SUPPLIES REQUIRED Flat-tip screwdriver T-30 Torx bit Eye protection (face shield, safety goggles, etc.) File Felt-tip pen Blanket Approx. 120 mm height empty cardboard box Torque wrench Ruler Tape The following tools are available through the Honda Tool and Equipment program. On the in, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under Search. Or call Air saw (Snap-on AT192A) Plastic Trim Tool (T/N: SILTRIMTL10) Illustration of the Roof Rack Rails on the Vehicle Cap A, right RIGHT ROOF RACK RAIL RACK RAIL 4 Caps B Cap C, left Cap C, right Q0D0903AD 12 Torx nuts 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 08L02-T0A of 6

2 INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 2. Using a plastic trim tool, pry up on the left roof molding cover to release one retaining tab and one clip. RETAINING COVER NOTE: Be extremely careful not to damage the roof and other finished surfaces of the body when installing the roof rack rails. The weight of the cargo must not exceed the maximum weight capacity of 75 kg (165 lbs). Installing the Roof Rack Rails 1. Measure rearward from the windshield molding, and mark the left roof molding at the measurement shown. TRIM TOOL TAILGATE QA22108AD MARK 17 mm (0.7 in.) 3. Pull the left roof molding toward the outside of vehicle to release the locking tab, and then press the locking tab toward the inside of vehicle, and release the left roof molding from the vehicle. When removing the left roof molding, start from the rear of vehicle and work towards the front. WINDSHIELD FELT-TIP PEN QA11301AD Press toward inside of vehicle. CROSS SECTION LOCKING Pull toward outside of vehicle. LOCKING Q0D0801BD 2 of 6 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

3 4. While pulling up the left roof molding, remove the two clips. Insert the plastic trim tool alternately to each slots in the clip, and release the locking tabs in the order shown. When removing the left roof molding, start from the rear of vehicle and work towards the front. Be careful not to deform the roof molding. 5. Place a blanket over the roof of vehicle under the left roof molding. Be careful not to deform the roof molding when measuring and cutting TRIM TOOL TRIM TOOL LOCKING BLANKET Q0D0802CD Approx. 7 mm (0.3 in.) width. 6. Place an empty cardboard box (approx. 120 mm tall) under the left roof molding near the mark. Approx. 1 mm (0.04 in.) thickness. TRIM TOOL MARK Approx. 120 mm (4.7 in.) QA60801AG EMPTY CARDBOARD BOX Q0D0803BD 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 3 of 6

4 7. While wearing an eye protection, use an air saw to cut the left roof molding at the mark. Do not use a cutting wheel or shears to cut the left roof molding, it will damage the left roof molding. Have an assistant hold the rear edge while cutting. 10. Insert flat-tip screwdrivers alternately between the green clip and the stud bolt as shown. While pulling on the green clip, release the locking tab on the green clip from the groove on the stud bolt notch by notch, and remove the green clip. Repeat the same procedure to remove the two purple clips. FLAT-TIP SCREWDRIVERS Alternately insert to release the locking tab. STUD BOLT FLAT-TIP SCREWDRIVERS LOCKING CROSS SECTION STUD BOLT MARK AIR SAW Q0D0804BD 8. Remove the cardboard box and blanket. 9. Secure the roof molding to the two clips removed in step 4. GREEN PURPLE Q0D0805BD QA60802AG 4 of 6 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.

5 11. Remove the red clip and the three yellow clips. 13. Reinstall the left roof molding cover in its original position on the roof. YELLOW RETAINING COVER RED Q0D0806BD 12. Using a flat-tip screwdriver wrapped with electrical tape, remove the left roof molding cover from the left roof molding (one retaining tab). Discard the left roof molding. TAILGATE QA22110AD 14. Install the left roof rack rail to the vehicle using six Torx nuts. Torque the Torx nuts to N m (8-11 lbf ft). Discard. RACK RAIL COVER 6 TORX NUTS ELECTRICAL TAPE 6 STUD BOLTS Q0D0807AD FLAT-TIP SCREWDRIVER RETAINING QA22109BD 2013 American Honda Motor Co., Inc. All Rights Reserved. AII (1307) 5 of 6

6 15. Install cap A (left) to the front of left roof rack rail. 17. Install cap C (left) to the rear of left roof rack rail. CAP A (LEFT) CAP C (LEFT) OF LEFT ROOF RACK RAIL Q0D0808AD REAR OF LEFT ROOF RACK RAIL Q0D0902AD 16. Install two caps B to the middle of left roof rack rail. 18. Repeat steps 1 through 17 to install the right roof rack rail on the right side of the vehicle. 2 CAPS B USE AND CARE Check the roof rail mounting bolts frequently, and re-tighten if necessary. MIDDLE OF LEFT ROOF RACK RAIL Q0D0901AD 6 of 6 AII (1307) 2013 American Honda Motor Co., Inc. All Rights Reserved.