Applications. LB Type 2-1/2-4 NEC 6x. C Type NEC 8x LB Type 1-2 NEC 6x. UB Type NEC 6x LR Type NEC 6x LL Type NEC 6x

Transcription

1 NEC 6x8x Series C, LB, UB and LL, LR, T Mogul Unilet Conduit Outlet Bodies For use with Threaded Rigid Metal Conduit and IMC. Complete with Assembled Cover and Neoprene Gasket. Applications Larger body size facilitates pulling of large and heavy conductors. Specially designed raised cast covers provide additional wiring area. Mogul Unilets for pulling straight, 5 or 90 angle turns and/or making taps and splices. Features Exclusive built-in rollers facilitate cable pulling. Available on NEC 6x8x Series Moguls (C, LB and UB) in sizes -/ and up. Smooth, rounded integral bushing in each hub protects conductor insulation. Accurately tapped, tapered threads for tight, rigid joints and ground continuity. Covers have captive stainless steel screws to speed installation, prevent freezing of screws. LB and UB Moguls Length Requirement: distance between centerline of each hub bushing (conduit stop) exceeds six times the trade diameter of the conduit per NEC 3.8(A)(). Bending Space Requirement: these moguls also meet the NEC 3.8(A)() Exception requirement spelled out in NEC 3.6(A) Table. C Moguls Length Requirement: distance between centerline of each hub bushing (conduit stop) exceeds eight times the trade diameter of the conduit per NEC 3.8(A)(). Bending Space Requirement: not applicable. LL and LR Moguls Like LB moguls, these moguls have an end hub. The second hub is in the side (LL left and LR right) instead of the back. T Moguls These are like C moguls ( thru ), except with an additional middle side hub. Distance between the centerline of each C hub conduit stop exceeds eight times the trade diameter of the conduit per NEC 3.8(A)(). Standard Materials Bodies and covers: malleable iron or copperfree (/0 of % max.) aluminum Gaskets: neoprene Screws: stainless steel Standard Finishes Malleable iron bodies and covers: triple-coat () zinc electroplate, () chromate and (3) epoxy powder coat Aluminum bodies and covers: epoxy powder coat NEC/CEC Certifications and Compliances UL Standard: 5B UL Listed: E57 CSA Standard: C. No. 8.3 CSA Certified: NEMA Standard: FB- C NEC 8x LB - NEC 6x LB -/ - NEC 6x UB NEC 6x LR NEC 6x LL NEC 6x T NEC 8x Rollers make cable-pulling easier, eliminate insulation damage Fittings NEC/CEC CONDUIT BODIES If less than maximum conductors permitted by NEC are used, smaller wires may be used additionally through LL, LR or T hubs. If large conductors are required to be bent in LL, LR or T direction, order junction boxes instead. See Enclosures and Junction Boxes. Visit our website at or contact us at (800) May 0 3

2 NEC 6x8x Series C, LB, UB Mogul Unilet Conduit Outlet Bodies For use with Threaded Rigid Metal Conduit and IMC. Complete with Assembled Cover and Neoprene Gasket. Hub Size Body, Cover and Gasket Cover and Gasket Malleable Iron Aluminum Gasket Only Malleable Iron Aluminum C NEC 8X Fittings BC00-M BC00-A BG00 BKG00-M BKG00-A -/ BC5-M BC5-A BGC5 BKGC5-M BKGC5-A - -/ BC50-M BC50-A BG50 BKG50-M BKG50-A BC00-M BC00-A BGC00 BKGC00-M BKGC00-A NEC/CEC CONDUIT BODIES LB NEC 6X -/ - -/ BC50-M BC50-A BGC50 BKGC50-M BKGC50-A 3 BC300-M BC300-A BGC300 BKGC300-M BKGC300-A 3-/ BC350-M BC350-A BGC350 BKGC350-M BKGC350-A BC00-M BC00-A BGC00 BKGC00-M BKGC00-A BLB00-M BLB00-A BG00 BKG00-M BKG00-A -/ BLB5-M BLB5-A BGL5 BKGL5-M BKGL5-A -/ BLB50-M BLB50-A BG50 BKG50-M BKG50-A - BLB00-M BLB00-A BGL00 BKGL00-M BKGL00-A -/ BLB50-M BLB50-A BGL50 BKGL50-M BKGL50-A 3 BLB300-M BLB300-A BGL300 BKGL300-M BKGL300-A 3-/ BLB350-M BLB350-A BGL350 BKGL350-M BKGL350-A -/ - BLB00-M BLB00-A BGL00 BKGL00-M BKGL00-A UB NEC 6X BUB00-M BUB00-A BG00 BKG00-M BKG00-A -/ BUB5-M BUB5-A BGL5 BKGL5-M BKGL5-A -/ BUB50-M BUB50-A BG50 BKG50-M BKG50-A - BUB00-M BUB00-A BGL00 BKGL00-M BKGL00-A -/ BUB50-M BUB50-A BGL50 BKGC50-M BKGC50-A 3 BUB300-M BUB300-A BGL300 BKGU300-M BKGU300-A 3-/ BUB350-M BUB350-A BGL350 BKGC350-M BKGC350-A -/ - BUB00-M BUB00-A BGL00 BKGU00-M BKGU00-A Furnished with rollers for easier cable pulling. 3 Visit our website at or contact us at (800) May 0

3 NEC 6x8x Series LL, LR, T Mogul Unilet Conduit Outlet Bodies and Wiring Capacity For use with Threaded Rigid Metal Conduit and IMC. Complete with Assembled Cover and Neoprene Gasket. Hub Size Body, Cover and Gasket Cover and Gasket Malleable Iron Aluminum Gasket Only Malleable Iron Aluminum LL NEC 6X LR NEC 6X T NEC 8X - - BLL00-M BLL00-A BG00 BKG00-M BKG00-A -/ BLL5-M BLL5-A BGL5 BKGL5-M BKGL5-A -/ BLL50-M BLL50-A BG50 BKG50-M BKG50-A BLL00-M BLL00-A BGL00 BKGL00-M BKGL00-A BLR00-M BLR00-A BG00 BKG00-M BKG00-A -/ BLR5-M BLR5-A BGL5 BKGL5-M BKGL5-A -/ BLR50-M BLR50-A BG50 BKG50-M BKG50-A BLR00-M BLR00-A BGL00 BKGL00-M BKGL00-A Fittings NEC/CEC CONDUIT BODIES BT00-M BT00-A BG00 BKG00-M BKG00-A -/ BT5-M BT5-A BGC5 BKGC5-M BKGC5-A -/ BT50-M BT50-A BG50 BKG50-M BKG50-A - BT00-M BT00-A BGC00 BKGC00-M BKGC00-A -/ BT50-M BT50-A BGC50 BKGC50-M BKGC50-A 3 BT300-M BT300-A BGC300 BKGC300-M BKGC300-A 3-/ BT350-M BT350-A BGC350 BKGC350-M BKGC350-A -/ - BT00-M BT00-A BGC00 BKGC00-M BKGC00-A Wiring Capacity for Mogul Bodies with Covers: Malleable Iron and Aluminum Hub Size Mogul Capacity dm 3 (in 3 ) Hub Size Mogul Capacity dm 3 (in 3 ) -/ -/ C, LB, LL, LR, T, UB 0.50 (3.00) -/ C, T 5.9 (335.00) LB 3. (0.00) C, T 0.8 (50.00) UB 6.5 (375.00) LB 0.79 (8.00) C, T 7.78 (75.00) LL, LR 0.69 (.00) 3 LB 5.65 (35.00) UB 0.66 (0.00) UB 7.9 (5.00) C, LL, LR, T.5 (93.00) C, T 3.60 (830.00) LB.75 (07.00) 3-/ LB 8.9 (500.00) UB.9 (9.00) UB 3.77 (80.00) C, T.3 (3.00) C, T 6.55 (00.00) LB.37 (5.00) LB.3 (70.00) LL, LR, UB.0 (3.00) UB 5.73 (960.00) Visit our website at or contact us at (800) May 0 33

4 Bending Radius and Bending Space of NEC 6x8x Series LB and UB Mogul Bodies Bending Radius of Moguls Catalog Number Hub Size R Millimeters R Fittings BLB00-A,M. (.63) 66.8 (.63) BLB5-A,M -/ 57. (.5) 9. (3.63) BLB50-A,M -/ 66.8 (.63) 0.9 (.3) NEC/CEC CONDUIT BODIES LB Mogul - LB Mogul -/ - LB BLB00-A,M 76. (3.00) 7.0 (5.00) BLB50-A,M -/ 98.6 (3.88) 58.8 (6.5) BLB300-A,M (5.00) 03. (8.00) BLB350-A,M 3-/ 7.0 (5.00).9 (8.38) BLB00-A,M 58.8 (6.5) 60. (0.5) BUB00-A,M.3 (.50) 39.7 (5.50) BUB5-A,M -/ 7.6 (.63) 5. (6.00) BUB50-A,M -/ 77.8 (7.00) 5.9 (8.50) UB BUB00-A,M 90.5 (7.50).3 (9.50) BUB50-A,M -/ (3.3) (5.50) BUB300-A,M (3.88) 8.8 (6.88) UB Mogul - BUB350-A,M 3-/ 50.7 (9.75) (3.5) BUB00-A,M 57. (0.75) 68.7 (.75) Compliances with NEC Bending Space Requirements Bending Space Defined NEC 370.8(A)() Exception. This article applies to LB and UB Moguls, defines bending space and refers to NEC 3.6(B) Table as guideline for determining minimum bending space distance. Bending space is illustrated as Dimension A below: Bending Space of Moguls (Dim. A in sketches at left) Mogul Size Distance LB, UB -/ -/ LB, UB 3-/ -/ LB, UB LB, UB 5 -/ LB, UB 6 3 LB, UB 8 3-/ LB, UB 8 AWG or Circular-Mill. Minimum Wire Bending Space NEC 3.6(B) Table: The applicable portion of this table is shown below. Only the Wire Per Terminal column is retained, because the others are not applicable. Example for using table below and table at right: 350MCM wire size requires 5 bending space. A LB or UB Appleton Mogul is suitable. LB, UB 0 Size of Wire Wire per Terminal Min. Bending Space LB Mogul - -0 Not Specified LB Mogul -/ - NOTE ON RADIUS TABLE: Secure cable or wire bending radius from manufacturer. Then select a mogul having this radius or more. If radius is 6-/, an LB -/ mogul or BUB -/ mogul is suitable. NOTE ON NEC 3.6(B) TABLE: Because cable sizes vary, table is limited to single wire sizes. Use as guideline only for cable sizes / -3 -/ / MCM -/ MCM MCM MCM MCM 8,000-,50 MCM 0 UB Mogul -,500-,000 MCM 3 Visit our website at or contact us at (800) May 0

5 NEC 6x8x Series C Mogul Bodies Comply with NEC Large-Wire Requirements Applicable NEC References for C, LB and UB Moguls Straight Pull Length Requirements: NEC 3.8(A)() C Moguls... shall not be less than eight times the trade diameter of the largest raceway. (See table at right.) Angle or U Pull Length Requirements: NEC 3.8(A)() LB, UB Moguls The distance between each raceway entry inside the box and the opposite wall of the box shall not be less than six times the trade diameter of the largest raceway. (See next page.) Bending-Space Requirements: NEC 3.8(A)(). Exception 3.6(A) Table LB, UB Moguls Where a conduit or cable entry is in the wall of a box or conduit body opposite to a removable cover. (See dim. A, table right) Length and Bending Space Requirements: C Mogul thru LB Mogul thru LB Mogul -/ thru UB Mogul thru BENDING SPACE EXAMPLE: LB with 3 hubs (Cat. No. BLB300-M) using 500 MCM wire with four conductors. Table on next page shows that, in this example, NEC requires a bending space of 6 and that the Appleton 3 LB provides a bending space of 8. * Dimension A is bending space. C Moguls Straight Pulls: Maximum Number of Conductors, Minimum Lengths Wire Size Maximum Number of Conductors per NEC Length Requirements (Conduit Stop to Conduit Stop) Per NEC Appleton Maximum Number of Conductors per NEC Length Requirements (Conduit Stop to Conduit Stop) Per NEC Appleton Hubs BC00-M and BC00-A -/ Hubs BC5-M and BC5-A / Hubs BC50-M and BC50-A Hubs BC00-M and BC00-A / Hubs BC50-M and BC50-A 3 Hubs BC300-M and BC300-A / Hubs BC350-M and BC00-A Hubs BC00-M and BC00-A NEC 370.8(A). Limited to minimum # wire. NEC Chapter 9, Table 3B. NEC 370.8(A)(). This is 8 times conduit trade size. Fittings NEC/CEC CONDUIT BODIES Visit our website at or contact us at (800) May 0 35

6 NEC 6x8x Series LB, UB Mogul Bodies Comply with NEC Large-Wire Requirements Fittings NEC/CEC CONDUIT BODIES LB and UB Moguls- Angle or U Pulls: Max. No. Conductors, Min. Lengths, Min. Bending Spaces Wire Maximum Number of Length Requirements (Conduit Stop to Conduit Stop) (A) Bending Space Requirements Maximum Number of Length Requirements (Conduit Stop to Conduit Stop) (A) Bending Space Requirements Size Conductors Per Per Conductors Per Per per NEC NEC Appleton NEC Appleton per NEC NEC Appleton NEC Appleton Hubs BLB00-M, BLB00-A, BUB00-M and BUB00-A -/ Hubs BLB5-M, BLB5-A, BUB5-M and BUB00-A 6 6 -/ 7 7-/ 7-/ 3-/ / 6 7-/ 7-/ 3-/ / -/ 5 7-/ 7-/ -/ 3-/ / 7-/ 3 3-/ / 7-/ 3-/ 3-/ -/ Hubs BLB50-M, BLB50-A, BUB50-M and BUB50-A Hubs BLB00-M, BLB00-A, BUB00-M and BUB00-A / -/ / 7 3-/ / 6 3-/ / / Hubs BLB50-M, BLB50-A, BUB50-M and BUB50-A 3 Hubs BLB300-M, BLB300-A, BUB300-M and BUB300-A / / / / / / / / / Hubs BLB350-M, BLB350-A, BUB350-M and BUB350-A Hubs BLB00-M, BLB00-A, BUB00-M and BUB00-A / 8 3 -/ / / / 8 3-/ / 8 -/ NEC 370.8(A). Limited to minimum # wire. NEC Chapter 9, Table 3B. NEC 370.8(A)() This is 6 times conduit trade size. NEC 370.8(A)() Exception (3.6(B) Table). This is distance A bending space illustrated on preceding page. 36 Visit our website at or contact us at (800) May 0

7 NEC 6x8x Series C, T, LL, LR Mogul Body Dimensions Mogul C T LL, LR Hub Trade Size -/ -/ -/ 3 3-/ -/ -/ -/ 3 3-/ -/ -/ s C, T Dimensions in Millimeters s LB, LL, LR A B C D E F G H J K (9.8) (.75) (.38) (.88) (6.63) (0.9) (.) (.88) (.00) (3.3) (.38) (.88) (7.69) (.6) (3.00) (.9) (3.9) (3.75) (3.3) (.50) (9.3) (.38) (3.38) (.56) (7.9) (.) (3.3) (.50) (3.00) (.63) (.00) (3.8) (3.5) (5.3) (.63) (3.75) (7.50) (.8) (.63) (3.63) (6.88) (5.9) (.63) (3.63) (.00) (.6) (5.) (.38) (3.38) (7.9) (5.63) (.50) (.9) (.50) (6.69) (.88) (35.38) (7.56) (5.63) (.50) (8.9) (.75) (7.06) (5.5) (9.8) (.75) (.38) (.88) (6.63) (3.5) (0.9) (.) (.88) (.00) (3.3) (.38) (.88) (8.56) (3.38) (.6) (3.00) (.9) (3.9) (3.75) (3.3) (.50) (0.38) (.3) (.38) (3.38) (.56) (7.9) (.) (3.3) (.50) (.3) (.3) (.63) (.00) (3.8) (3.5) (5.3) (.63) (3.75) (8.69) (6.00) (.8) (.63) (3.63) (6.88) (5.9) (.63) (3.63) (.9) (6.00) (.6) (5.) (.38) (3.38) (7.9) (5.63) (.50) (6.9) (7.5) (.50) (6.69) (.88) (35.38) (7.56) (5.63) (.50) (30.9) (7.5) (.75) (7.06) (5.5) (8.9) (.75) (.38) (.88) (6.63) (3.5) (0.9) (.) (7.88) (.88) (9.69) (3.3) (.38) (.88) (7.5) (3.38) (.6) (3.00) (8.50) (.9) (3.00) (3.75) (3.3) (.50) (0.38) (.3) (.38) (3.38) (.63) (.56) (.63) (5.00) (3.3) (.50) (.8) (.3) (.63) (.56) (.9) (3.) Number of Cover Holes Fittings NEC/CEC CONDUIT BODIES Furnished with rollers for easier cable pulling. Visit our website at or contact us at (800) May 0 37

8 NEC 6x8x Series LB, UB Mogul Body Dimensions Fittings NEC/CEC CONDUIT BODIES Mogul LB UB Hub Trade Size -/ -/ -/ 3 3-/ -/ -/ -/ 3 3-/ LB -/" thru " UB Dimensions in Millimeters Number A B C D E G H J K L of Cover Holes (8.9) (3.63) (.38) (.88) (6.63) (0.9) (.) (7.88) (.88) (.88) (9.69) (.75) (.38) (.88) (6.3) (.6) (3.) (8.50) (.63) (.6) (3.00) (5.5) (3.3) (.50) (9.3) (.38) (3.9) (.63) (3.06) (.38) (.63) (6.3) (3.3) (.50) (0.75) (.63) (.88) (.9) (3.) (.69) (7.88) (8.00) (5.88) (3.50) (3.75) (.3) (.3) (5.8) (.56) (.06) (0.00) (5.88) (3.50) (7.00) (.50) (5.3) (8.50) (5.38) (.3) (0.5) (7.00) (.63) (9.88) (3.00) (.75) (.38) (6.63) (7.50) (.50) (7.00) (.63) (3.00) (3.5) (6.38) (.38) (7.00) (9.63) (3.50) (.38) (.88) (6.63) (.) (8.) (.88) (0.5) (.3) (.38) (.88) (6.3) (3.00) (8.9) (.9) (3.69) (.63) (3.3) (.50) (9.3) (3.38) (.9) (.56) (5.5) (5.00) (3.3) (.50) (0.75) (.56) (3.38) (3.8) (.88) (7.06) (.63) (3.75) (7.50) (5.) (0.3) (.38) (.88) (7.3) (.63) (3.75) (7.50) (6.8) (0.3) (.38) (30.88) (8.9) (5.63) (.50) (.88) (7.06) (7.50) (5.5) (30.88) (0.3) (5.63) (.50) (.88) (8.) (7.50) (5.5) Furnished with rollers for easier cable pulling. 38 Visit our website at or contact us at (800) May 0