Scion Multi-kit

Transcription

1 Installation instructions for part KIT FEATURES DIN radio provision with pocket ISO DIN radio provision with pocket ISO DDIN radio provision Scion Multi-kit TOOLS REQUIRED Cutting tool Phillips screwdriver 10mm socket wrench Grinder Panel removal tool WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: Antenna Adapter: Not required KIT COMPONENTS A) Radio housing B) Bracket Set 1 C) Bracket Set 2 D) ISO DIN brackets E) ISO DDIN radio brackets F) ISO DIN trim plate G) DIN spacer A B C D REV. 6/28/2016 INST E F G APPLICATIONS See application list inside cover CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. METRA. The World s best kits. metraonline.com COPYRIGHT METRA ELECTRONICS CORPORATION

2 Applications Table of Contents SCION tc tc * xa * ISO DDIN radio provision only xb xd Dash Disassembly tc tc xa xb xb xd Kit Assembly. DIN radio provision with pocket ISO DIN radio provision with pocket ISO DDIN radio provision

3 Dash Disassembly Scion tc Unsnap trim from around shifter (not necessary to be removed). (Figure A) 2. Unclip and remove panel from around radio. (Including climate controls and radio door). (Figure B) 3. Remove (2) 10mm nuts from the top B mounting locations and (2) 10mm bolts from the bottom mounting locations to remove the radio. (Figure C) 4. If installing a ISO DDIN aftermarket radio, remove factory brackets from radio. Retain brackets for use during kit assembly. Continue to kit assembly (Figure A) (Figure B) (Figure C) 3

4 Dash Disassembly Scion tc Unclip and remove the radio trim panel. (Figure A) 2. Remove (4) 10mm bolts securing the radio. (Figure B) 3. If installing a ISO DDIN aftermarket radio, remove factory brackets from radio. Retain brackets for use during kit assembly. Continue to kit assembly (Figure A) (Figure B) 4

5 Dash Disassembly Scion xa Pull outward on the (3) climate control knobs and remove. (Figure A) HI 2. Remove (2) Phillips screws from behind the outer two climate knobs. (Figure B) HI 3. Unsnap and remove the trim pieces on each side of the climate control/ashtray/pocket assembly. (Figure C) 4. Remove (2) phillips screws from the bottom of the climate control/ radio trim panel and unsnap and remove the entire panel. (Figure D) (Figure A) (Figure C) 5. Remove (4) Phillips screws to remove the factory radio. HI HI 6. If installing a ISO DDIN aftermarket radio, remove factory brackets from radio. Retain brackets for use during kit assembly. Continue to kit assembly (Figure B) (Figure D) 5

6 HI Dash Disassembly Scion xb Pull outward on the (3) climate control knobs and remove. (Figure A) 2. Remove (2) Phillips screws from behind the outer (2) knobs. (Figure B) HI HI 3. Unsnap and remove the entire panel B surrounding the climate controls and the radio. (Figure C) 4. Remove (4) Phillips screws to remove the factory radio. (Figure A) (Figure B) (Figure C) 5. If installing a ISO DDIN aftermarket radio, remove factory brackets from radio. Retain brackets for use during kit assembly. Continue to kit assembly 6

7 Dash Disassembly Scion xb Unclip and remove the trim panel around the radio including the a/c vents. (Figure A) 2. Unclip and remove the trim panel at the bottom edge of the dash cavity. (Figure B) 3. Remove (4) 10mm bolts securing the radio. (Figure C) 4. If installing a ISO DDIN aftermarket radio, remove factory brackets from radio. Retain brackets for use during kit assembly. Continue to kit assembly (Figure A) (Figure B) (Figure C) 7

8 Dash Disassembly Scion xd Unclip radio trim panel. Unplug and remove panel. (Figure A) 2. Remove (4) Phillips screws securing the radio. Unplug and remove radio. (Figure B) 3. If installing a ISO DDIN aftermarket radio, remove factory brackets from radio. Retain brackets for use during kit assembly. (Figure C) Continue to kit assembly (Figure A) (Figure C) (Figure B) 8

9 DIN radio provision with pocket 1. Slide the mounting brackets onto the sides of the radio housing until the side clips engage. (Figure A) Note: Use Bracket Set 1 for xa, xb , and tc Use Bracket Set 2 for the xb and xd For Bracket Set 1 cut and remove all mounting tabs except the tabs being used for your application. (Figure B) Note: Tabs are marked xa, xb and tc. For Bracket Set 2 skip to step Remove the metal DIN sleeve from the aftermarket radio. 4. Slide the sleeve into the radio housing and secure by bending the metal locking tabs outward. (Figure C) Note: A DIN spacer has been provided if extra depth is required. This will go into the radio housing before the sleeve. 5. Slide the aftermarket radio into the sleeve until it snaps into place. (Figure D) 6. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation. 7. Secure the completed assembly into the dash, and then reassemble the dash in reverse order of disassembly. (Figure A) (Figure B) Kit Assembly Bracket Set 1 9 Side clips (Figure C) (Figure D)

10 Kit Assembly ISO DIN radio provision with pocket 1. Slide the mounting brackets onto the sides of the radio housing until the side clips engage. (Figure A) Note: Use Bracket Set 1 for xa, xb , and tc Use Bracket Set 2 for the xb and xd For Bracket Set 1 cut and remove all mounting tabs except the tabs being used for your application. (Figure B) Note: Tabs are marked xa, xb and tc. For Bracket Set 2 Side clips skip to step Remove the metal DIN sleeve and trim ring from the aftermarket radio. (Figure A) (Figure C) 4. Mount the ISO DIN brackets to the radio using the screws supplied with the radio. (Figure C) 5. Slide the bracket/radio assembly into the radio housing until it Bracket snaps into place. (Figure D) Set 1 6. Snap the ISO DIN trim plate onto the front of the radio housing. (Figure D) 7. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation. 8. Secure the completed assembly into the dash, and then reassemble the dash in reverse order of disassembly. (Figure B) (Figure D) 10

11 Kit Assembly ISO DDIN radio provision 1. For Scion tc and xa models only: Cut off the front upper section of the ISO DDIN brackets as shown. (Figure A) 2. Secure the factory mounting brackets, and the ISO DDIN brackets to the radio with the screws supplied with the radio. (Figure B) Note: Remove the locating pins from the factory brackets with a grinder. 3. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation. 4. Secure the completed assembly into the dash, and then reassemble the dash in reverse order of disassembly. (Figure A) (Figure B) 11

12 Installation instructions for part IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. REV. 6/28/2016 INST KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto or call for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World s best kits. metraonline.com COPYRIGHT METRA ELECTRONICS CORPORATION