Getting Start for Using Wireless Keyboard and Mouse / Wireless Keyboard User s Guide

Transcription

1 Getting Start for Using Wireless Keyboard and Mouse / Wireless Keyboard User s Guide Introducción al uso del teclado y del ratón inalámbricos/ Guía del usuario del teclado inalámbrico ワイヤレスキーボードとマウスを使用するにあたって / ワイヤレスキーボードユーザーズガイド Erste Schritte für drahtlose Tastatur und Maus / Benutzerhandbuch für drahtlose Tastatur Clavier et souris sans fil démarrer / Clavier sans fil guide de l utilisateur 無線鍵盤和滑鼠啟用程序 / 無線鍵盤使用指南

2 Getting Start for Using Wireless Keyboard and Mouse 1. Turn off your computer and all attached devices. Before starting up, please follow the direction marked in the battery compartment to insert two AAA batteries into the mouse and two AA batteries into the keyboard. 2. Plug the receiver into the USB port and start up the system. 3. Microsoft Windows Millennium Edition and Windows 2000 Professional will automatically recognize the Receiver. Windows 98 Second Edition will require manual prompting. Click Next on all prompts and then click Finish. (see notice for detail) Follow the on screen instruction, you may also need to insert your Windows 98 Second Edition CD and browse the necessary files for complete installation. 4. Press one of the Windows keys and confirm customization launch. Move the mouse to confirm movement. If the above does not work, go to step 5. Otherwise, go to step First, press the channel search button on the top of the receiver and note the green LED will blink slowly. Then, press the channel change button on the rear side of keyboard/mouse to a new channel. Note the green LED on the receiver will blink faster to notify a new channel is identified. Press any mouse key (left, right, or middle)/keyboard key button for 1 sec to confirm the channel matching process. 6. See your system User s Guide for instructions on how to use your Wireless Mouse and Wireless Keyboard. De-activate and Activate of Wireless Mouse Your wireless mouse can be deactivated to save battery power and to avoid unintentionally RF transmission. 1. To de-activate your wireless mouse, hold down the middle button then press the channel selection button. 2. To activate your wireless mouse, hold down either Left button or Right button then press down the channel selection button for three seconds. Frequently Asked Questions: 1. Q: Why the mouse doesn t work? A: 1) See step 5 above for the channel matching process. 2) Check your system s User Guide for correct USB installation. 3) Follow the step above to activate your wireless mouse.

3 2. Q: Why the mouse movement is not smooth. A: 1) Current channel may be interfered. See step 5 above to select a new channel. Possible interference sources may include your microwave oven, DECT wireless phone, wireless LAN, and any other devices operated at the 2.4 GHz frequency band. 2) This wireless mouse is designed to work with your notebook computer. It has the best sensitivity when the mouse and receiver are in the same horizontal plane. 3. Q: Why the keyboard LED is red? A: Batteries in the keyboard are getting out of power. Please replace new batteries. Notice: It's necessary to connect an extra USB keyboard, PS/2 keyboard or mouse to your computer to click all Next and Finish prompts manually to finish USB device recognizing when running in Windows 98 Second Edition. FCC GUIDE LINES WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, Uses and can radiated radio frequency energy and if not installed and used in accordance with the instructions," may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/tv technician for help. Shielded interface cables must be used in order to comply with emission limits. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Microsoft and Windows are trademarks or registered trademarks of the Microsoft Corporation in the United States, other countries or both. Printed in China

4 WIRELESS KEYBOARD USER S GUIDE System Requirements Windows 98 Second Edition/2000 operation system (for Touch Manager software; hardware will operate for any IBM compatible PC) USB port FOR ACPI POWER MANAGEMENT Your keyboard includes three ACPI power management keys Power, Sleep and Wakeup, located at the top of the keyboard that provide you with a convenient way to manage your PC s power system. To utilize these three keys, your system is required to meet the following requirements: Microsoft Windows 98 Second Edition and above operating system ACPI compliant motherboard System BIOS supports PC 99 Wake, Sleep, Power modes ATX motherboard power supply Refer to your computer hardware documentation regarding power-management operation. Ensure that the power-management settings for your operating system are correct, as described in Windows Help. Note that Windows 95 and NT 4.0 do not support ACPI power management feature. Keyboard Connection 1. Locate the USB port on your computer. Consult your computer user s manual for information on the location of your computer s peripheral ports. 2. Align your Internet Keyboard USB connector with the USB port. Gently insert the USB connector into the USB port. Refer to the following illustration: NOTE: The Hot Keys on the top of your keyboard will not function until the Touch Manager software has been installed. Windows contains embedded support for your keyboard Hot Keys. 3. When you have successfully connected the USB connector, the Add New Hardware wizard opens in Windows. Follow the instructions on the screen to complete the keyboard installation.

5 Touch Manager Software Installation To activate the hot keys on the top of your keyboard under Windows 98 Second Edition or above, you must install Touch Manager software included in the bundled CD. The installation of your Touch Manager software is a very simple process. 1. Windows 98 Second Edition has an auto-detect feature that automatically launches the installation program. Follow all of the on-screen instructions. 2. If the auto-run feature has been de-activated, select the My Computer icon on your desktop and double-click on your CD-ROM drive. Click on the SETUP.EXE file and follow all of the on-screen instructions. 3. Upon completion of the software installation, Touch Manager will be activated automatically. Touch Manager Software Uninstallation To uninstall Touch Manager follow instructions below. 1. From your Start menu, select Settings, Control Panel and click on the Add/Remove Programs icon. 2. From the Add/Remove Programs Properties, select Touch Manager (USB Internet Compact Keyboard) in the list and click Add/Remove button to uninstall. Touch Manager has now been uninstalled completely from the system. Using Touch Manager After completion of this software installation, the "Touch Manager" icon will appear at the lower right side of your screen in the system tray. Copyright Notice This manual and accompanying software are copyrighted. Unauthorized copying of either, including any portions of the software that have been modified, merged, or included with other software, is expressly forbidden. All company or product names are trademarks, registered trademarks or service marks of their respective owners. All specifications are subject to change without notice.