MODEL 351 POWERGLIDE SERIES INSTRUCTIONS FOR INSTALLING SARGENT DOOR CLOSERS WITH REGULAR ARMS (WITHOUT HOLDER)

Transcription

1 MODEL POWERGLIDE SERIES INSTRUTIONS FOR INSTLLING SRGENT LOSERS WITH REGULR RMS (WITHOUT HOLDER) SERIES NON SIZED DJUSTLE SIZES THRU 6 UTION: FILURE TO INSTLL OR DJUST PROPERLY MY RESULT IN INJURY OR DMGE. FOR SSISTNE, LL SRGENT T STNDRD PPLITION (TYPE -O RM) LOSER MOUNTED ON HINGE SIDE OF USE PGE NOTE: FOR 08 ND OL TYPE RMS MOUNTING SEE DT SHEETS ENLOSED STNDRD & TOP JM PPLITIONS WIDTH (INHES) OVER 8 NUMER OF TURNS OF SPRING POWER DJUSTING SREW FROM FTORY SETTING (USE HRT S GUIDE ONLY) PPROXIMTE INTERIOR S WEIGHT (POUNDS) EXTERIOR S 80 FTORY SET 0 - W 0 - W -7 W W FTORY SET W - W UP TO 8 W S REQ. W ND UP S REQ. DJUST SPRING POWER ORDING TO HRT* TOP JM PPLITION (TYPE -O, -OZ ND -OZ RMS) INRESE POWER + - DERESE POWER LOKWISE (W) OUNTER LOKWISE (W) USE PGE /8" SPRING POWER DJUSTMENT NUT LEFT HND PULL HINGE SIDE PULL HINGE SIDE RIGHT HND LOSER MOUNTED ON FRME ON STOP SIDE OF STOP (PUSH) SIDE STOP (PUSH) SIDE PRLLEL PPLITION ONLY PRLLEL RM PPLITION (TYPE -P9) LOSER MOUNTED ON STOP SIDE OF USE PGE WIDTH (INHES) OVER 8 NUMER OF TURNS OF SPRING POWER DJUSTING NUT FROM FTORY SETTING (USE HRT S GUIDE ONLY) PPROXIMTE INTERIOR S WEIGHT (POUNDS) EXTERIOR S W W - W 0 8- W FTORY SET W -7 W UP TO 8 W S REQ. 8 W ND UP S REQ. DJUST SPRING POWER ORDING TO HRT* *IF INTERIOR S DO NOT HVE TO OMPLY WITH D REQUIREMENTS, EXTERIOR SETTINGS RE REOMMENDED. WHERE STRONG DRFTS EXIST, INRESE SPRING POWER S NEEDED Y TURNING SPRING DJUSTMENT SREW LOKWISE. IF NEESSRY, REDUE SPRING POWER Y TURNING SREW OUNTERLOKWISE. opyright 00, 008, 0 Sargent Manufacturing ompany, an SS LOY Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of 70

2 STNDRD RM PPLITION INSTRUTIONS IMPORTNT: USE LTERNTE MOUNTING IF N OPEN EYOND LIMITS SHOWN FOR STNDRD MOUNTING RM TYPE REGULR RM NO HOLDER MOUNTING STNDRD 0 8 /6" LTERNTE MX. OPENING 60 6 /6" 7/6" 0 /6" IF UTT, FRME ND WLL ONDITIONS PERMIT WILL OPEN 80 "" "" TOP OF " # x WOOD SREWS OR #- X / FLT HED MHINE SREWS SEE PGE 6 FOR MORTISE NUTS /8" RIGHT HND SHOWN. LEFT HND OPPOSITE. THIS DIMENSION IS TKEN FROM HINGE EDGE OF FOR INVISILE HINGES. 9/6" /" DRILL & TP ND USE SREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED. USE TEMPLTE 67 FOR -OL RM (LOW PROFILE) 9" L OF HINGE PIVOT: UTTS, OFFSET PIVOTS, SWING LER, ENTER HUNG OR INVISILE HINGES INSTLL LOSER TO WITH SPRING DJUSTMENT NUT WY FROM HINGE. NOTE: LOSER ODIES RE NON HNDED. IT IS IMPORTNT THT THE LOSER ODY E MRKED WITH RH SYMOL T TOP, FOR RIGHT HND S. LH SYMOL T TOP FOR LEFT HND S. RH RIGHT HND SHOWN TTH FOOT TO FRME WITH PIVOT WY FROM HINGE. TTH RM WITH INDEX MRK ON SPINDLE LIGNED S SHOWN. SEURE WITH SREW ND WSHER. INSERT END INTO SWIVEL RM ND TIGHTEN RM SREW S SHOWN ELOW. RIGHT HND SHOWN (LEFT HND OPPOSITE) PIVOT MIN RM RM SREW 90 INDEX MRK ON SPINDLE POSITION OF MIN RM WHEN SSEMLING TO SPINDLE SWIVEL RM opyright 00, 008, 0 Sargent Manufacturing ompany, an SS LOY Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of 70

3 TOP JM PPLITION INSTRUTIONS RM TYPE O RM OZ RM REVEL DEPTH 0" TO " /8" TO " OPENING /8" /8" MX. OPENING 0 0 RIGHT HND SHOWN, LEFT HND OPPOSITE. THIS DIMENSION IS TKEN FROM HINGE EDGE OF FOR INVISILE HINGES. OZ RM /8" TO 8" 0 OPENING TO 80 IS POSSILE IF DEPTH OF REVEL IS NOT GRETER THN " DRILL & TP ND USE SREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED. /8" STOP MX /" /" 7/6" 9" /" 6" DIM OF PIVOT HINGE L - PLTE /" " SEE PGE 6 FOR MORTISE NUTS PROVIDE /6" DIMETER LERNE FRME HOLES IN FRME FOR LOSER SREWS SINGLE WHIH PROJET /6" EYOND PLTE RETED /" /" FRME " STOP /6" FRME " /" TOP OF DEPTH OF REVEL - MOUNTING PLTE " DOULE RETED FRME WITH REQUIRED /" MIN MOUNTING PLTE # X /" WOOD SREWS OR #- X /8" FLT HED MHINE SREW DEPTH OF REVEL " 7/6" INSTLL LOSER TO FRME WITH SPRING DJUSTMENT NUT WY FROM HINGE. NOTE: LOSER ODIES RE NON HNDED. IT IS IMPORTNT THT THE LOSER ODY E MRKED WITH RH SYMOL T TOP, FOR LEFT HND S. LH SYMOL T TOP FOR RIGHT HND S. TTH FOOT TO WITH PIVOT WY FROM HINGE. RIGHT HND SHOWN LH HINGE SIDE INSTLL MIN RM TO SPINDLE ND SEURE WITH SREW ND WSHER S SHOWN. OPEN INSERT RETNGULR INTO SWIVEL RM THEN LOSE THE ND TIGHTEN RM SREW SEURELY WHEN SWIVEL RM IS T RIGHT NGLE TO. FOOT PIVOT FOOT PIVOT LEFT HND RIGHT HND POSITION OF MIN RM WHEN SSEMLING TO SPINDLE RM SREW 90 MIN RM INDEX MRK ON SPINDLE 90 RM SREW POSITION OF MIN RM WHEN SSEMLING TO SPINDLE SWIVEL RM VIEW LOOKING UP WHEN SSEMLING RM TO SPINDLE SWIVEL RM opyright 00, 008, 0 Sargent Manufacturing ompany, an SS LOY Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of 70

4 parallel arm PPLITION INSTRUTIONS L OF HINGE PIVOT (UTT HINGE SHOWN) /6" /" /" MX. OPENING /8" 0 /" 7" 7 /8" /" 7/8" # WOOD SREWS OR #- x /8 FLT HED MHINE SREWS LEFT HND SHOWN. RIGHT HND DIMENSION OPPOSITE. TOP VIEW TOP OF DO NOT USE THIS MOUNTING FOR SWING LER HINGES. THIS DIMENSION IS TKEN FROM HINGE EDGE OF FOR INVISILE HINGES. DRILL & TP ND USE SREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED. /8" /" L OF HINGE PIVOT 9" STOP # X " WOOD SREWS OR #- X /" MHINE SREW SEE PGE 6 FOR MORTISE NUTS INSTLL LOSER TO WITH SPRING DJUSTMENT NUT WY FROM HINGE. TTH FOOT RKET TO FRME STOP. RIGHT HND SHOWN RH NOTE: LOSER ODIES RE NON HNDED. IT IS IMPORTNT THT THE LOSER ODY E MRKED WITH RH SYMOL T TOP, FOR RIGHT HND S. LH SYMOL T TOP FOR LEFT HND S. USING WRENH ON OTTOM END OF SPINDLE, ROTTE SPINDLE ND SSEMLE MIN RM TO LOSER S SHOWN, ND THEN INSERT END INTO SWIVEL RM ND TIGHTEN RM SREW POSITIONING RM /" WY FROM. LEFT HND VIEW OF INDEX INDEX MRK ON SPINDLE PRELOD PPROX. 0 RIGHT HND VIEW OF INDEX INDEX MRK ON SPINDLE MIN RM OPTIONL RMS FOR MOUNTING. SEE DT SHEET ENLOSED. P OR P RKET P OR P RKET (SRGENT #90 SHOWN) POSITION OF MIN RM WHEN SSEMLINGTO SPINDLE MIN RM UTION: LOSER WILL NOT OPERTE PROPERLY IF RM IS NOT INDEXED ORRETLY. /" MIN RM RM SREW RIGHT HND FOOT RKET FOR FLUSH FRME ND ONDITIONS P RKET IS USED WITH OVERHED HOLDERS opyright 00, 008, 0 Sargent Manufacturing ompany, an SS LOY Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of FOR USE WITH OVERHED HOLDERS 70

5 FINL DJUSTMENT ND REGULTING PROEDURE KHEK VLVE OPTIONL DELYED TION VLVE SPEED VLVE LTHING SPEED VLVE LTHING SPEED RNGE LOSING SPEED RNGE DELYED TION RNGE KHEK RNGE REGULTING SPEED ND LTHING SPEED S NEEDED. REGULTING KHEK USE HEX SOKET (/8" LLEN) WRENH ND TURN VLVES LOKWISE TO SLOW DOWN OR OUNTER LOKWISE TO SPEED UP MOVEMENT. FSTER (+) SLOWER ( ) TO REGULTE THE INTENSITY OF KHEK TION TURN VLVE LOKWISE TO INRESE OR OUNTER LOKWISE TO DERESE HEKING. UTION: SET VLVE FOR SLIGHT USHIONING EFFET. IT IS DMGING TO THE LOSER IF THE HEKING TION IS TOO RUPT. NEVER USE KHEK S STOP. LWYS USE STOP TO STOP THE. FOR MODELS WITH OPTIONL DELYED TION FETURE D DJUSTING FOOT FOR DDITIONL LOSING POWER (FOR STNDRD ND TOP JM PPLITIONS ONLY) DELYED TION PROVIDES SLOW LOSING THROUGH DELYED TION RNGE TURN VLVE LOKWISE TO SLOW DOWN OR OUNTER LOKWISE TO SPEED UP MOVEMENT MOVE FOOT PIVOT TO HOLE NEREST HINGE + + HINGE EDGE OF E INSTLL OVER WITH TWO SREWS S SHOWN. INSERT IS REMOVLE. PLE IN UNUSED OPENING. opyright 00, 008, 0 Sargent Manufacturing ompany, an SS LOY Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of 70

6 USING MORTISE NUTS WITH SRGENT LOSER. SEE INSTRUTIONS OR DT SHEET PKED WITH LOSER FOR DIMENSIONS LOTING THE LOSER ODY ND FOOT ON ND FRME.. MORTISE NUT SHOWN IS DESIGNED FOR N UNREINFORED METL.. FOR TOP JM ND ORNER RKET PPLITIONS: THE LOSER FOOT WILL E TTHED TO THE IN MNNER SIMILR TO THT SHOWN FOR MOUNTING THE LOSER ODY.. FOR S /" THIK: MORTISE NUT SHOWN FOR /" THIK S WILL E FURNISHED LONG WITH PPORPRITE LENGTH THRU-OLTS. ONSTRUTION MUST PROVIDE RIDGE TYPE REINFOREMENT TO PREVENT THE RIL FROM OLLPSING WHEN THRU-OLTS RE TIGHTENED. SRGENT 0 SERIES LOSER SHOWN. (OTHER SERIES SIMILR) SEE NOTE # ELOW FOR DIMENSION INFORMTION. IF DIMENSION LESS THN 7/8" IS USED. THE STOP MUST E UT TO LER THE MORTISE NUT HED OR THE MORTISE NUT HED MUST E REESSED. (SEE ENLRGED VIEW "Y") FRME STOP OVER MORTISE NUT HED DRILL /" DI. HOLE FOR MOUNTING SREWS DRILL /8" DI. HOLE FOR MORTISE NUT ODY. SHORTEN MORTISE NUT ODY TO THIS LENGTH SRGENT SERIES SHOWN FRME /8" /8" DI. HOLE STOP #- THRED 9/6" DI. LOSER SHOWN (TRK SSEMLY MOUNTING IS SIMILR) /" DI. DRILLED HOLE VIEW "Y" /8" DI. HOLE MORTISE NUT HED MORTISE NUT 7/6" /6" FOR /" THIK /6" FOR /8" THIK (SEE NOTE # FOR /" THIK S) opyright 00, 008, 0 Sargent Manufacturing ompany, an SS LOY Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of 70 6