Hustler X-ONE i Parts Manual

Transcription

1 Hustler X-ONE i Parts Manual 00 South Ridge Road Hesston, Kansas 6706

2 WARNING The engine exhaust from this product contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. NOTICE OF REQUIREMENT OF SPARK ARRESTER MUFFLER This equipment may create sparks that can start fires around dry vegetation. California Public Resources Code Section.6 provides that it is unlawful to use or operate an internal combustion engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester maintained in effective working order. A spark arrester is a device constructed of nonflammable materials specifically for the purpose of removing and retaining carbon and other flammable particles over 0.0 of an inch in size from the exhaust flow of an internal combustion engine that uses hydrocarbon fuels or which is qualified and rated by the United States Forest Service. Other states or federal areas may have similar laws. The Operator Should Contact Local Fire Agencies For Laws or Regulations Relating to Fire Prevention Requirements. THIS EQUIPMENT DOES NOT HAVE A SPARK ARRESTER AND YOU SHOULD CONTACT YOUR AUTHORIZED DEALER FOR THE PURCHASE OF A SPARK ARRESTER. Inspect spark arrester daily; replace every 500 hours or as needed. The Engine Owner s Manual provides information regarding the U.S. Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance and warranty. Keep Engine Owner s Manual with your unit. Should the Engine Owner s Manual become damaged or illegible, replace immediately. Replacements may be ordered per the information found in the Product Information section of the owner s manual. Federal law and California State law prohibit the following acts or the causing thereof:. The removal or rendering inoperative by any person other than for purposes of maintenance, repair, replacement, of any device or element of design incorporated into any equipment for the purposes of emissions control prior to or after its sales or delivery to the ultimate purchaser or while it is in use, or. The use of the equipment after such device or element of design has been removed or rendered inoperative by any person.

3 Table of Contents General Information Service Literature Options Available From Your Dealer Using This Manual Hardware Description Codes & Abbreviations Standard Torques Section Frame Engine Guard Decals Models Ending in "US" Section Hydraulic System Hydraulic Service Parts Steering Steering Box Assembly Brake Section Wheel & Tire Front Tire Breakdown Drive Wheel Breakdown Section 5 Engine, Kaw FX69V & FX70V (w/o Carbon Canister) Engine, Kaw FX69V & FX70V (with Carbon Canister) Fuel System S/N 0000 & Higher (w/o Carbon Canister) Fuel System S/N Prior to 0000 (w/o Carbon Canister) Fuel System (with Carbon Canister) Engine Service Parts, Kawasaki FX69V & FX70V Fuel Tank Service Parts Section 6 Battery Instrument Panel Section 7 5" Service Deck " Deck Pulleys & Spindles " Deck " Service Deck " Deck Pulleys & Spindles " Deck Deck Lift Deck Mounting Hardware Section 8 Seat, Deluxe Seat Service Parts, Deluxe ROPS S/N 050 & Higher _07 c-

4 ROPS S/N Prior to c- 760_07

5 General Information This manual covers Hustler X-ONE i models 999, 9956, 9US & 950US. Service Literature PART NO. DESCRIPTION 6066 OPERATOR S MANUAL 760 WARRANTY STATEMENT 760 GENERAL SERVICE MANUAL Options Available From Your Dealer PART NO. DESCRIPTION 606 FLEX FORK KIT 77 LIGHT KIT 596 STEERING EXTENSION KIT SEAT SUSPENSION KIT SEMI-PNEUMATIC TIRE/WHEEL ASSEMBLY 55 5" MULCH KIT 55 60" MULCH KIT 95 CATCHER 60" 995 CATCHER 5" Note: When ordering parts, you must use the part number as shown for each part, not the index number. Always give the model and serial number to your parts and service representative. Note: Items sold in bulk such as seals and hoses are sold by the foot. Using This Manual This manual is part of a service package for the Hustler mowers. Use of this manual in conjunction with other Hustler mower and component manuals will provide the information necessary to service and maintain Hustler mowers. This Parts Manual provides a complete parts listing for the unit. Use this manual when ordering parts. Illustrations used were current at the time of printing, but subsequent production changes may cause your machine to vary slightly in detail. Excel Industries, Inc. reserves the right to redesign and change the machine as deemed necessary, without notification. If a change has been made to your machine which is not reflected in this parts manual, see your authorized dealer for current information and parts. The Service Manual is a service guide for use by Service Technicians. It provides the necessary information needed to perform normal maintenance requirements on these units. The Operator's Manual provides fundamental operational information and operational safety that is needed when operating the mower. The component manuals are furnished by the various manufacturers to be used for the troubleshooting and servicing of their products. 760_07 -

6 Hardware Description Codes & Abbreviations The following codes are used throughout this parts manual. Refer to this list when ordering parts. ABBREVIATION DESCRIPTION ABBREVIATION DESCRIPTION CB CARRIAGE BOLT MB MACHINE BUSHING CE CLEVIS PIN MS MACHINE SCREW CN CLIP NUT NT NUT CP COTTER PIN SC SELF TAPPING CAP SCREW CS CAP SCREW SH SOCKET HEAD CW CUP WASHER SB SHOULDER BOLT FDRW FENDER WASHER SS SET SCREW FW FLAT WASHER OD OUTSIDE DIAMETER HX HEX HEAD ID INSIDE DIAMETER LW LOCK WASHER Standard Torques The following chart lists the standard torque values for the threaded fasteners found in this manual. Torque all cap screws, nuts and set screws to these values unless a different torque is shown in the Notes section next to the fastener. SIZE FT-LBS N-M SIZE FT-LBS N-M M.. 7 M M M M M M M M M0 0 5 M _07

7 Section Frame Engine Guard Decals Models Ending in "US" _07 -

8 Frame _07

9 Frame INDEX NO. PART NO. QTY. DESCRIPTION " FRAME (WITH DECALS & RIVET NUTS) " FRAME (WITH DECALS & RIVET NUTS) BUMPER 6007 HUSTLER ID DECAL 787 DECK HEIGHT DECAL /-0 THREAD RIVET NUT SAFE OPERATION DECAL 7 N/A SERIAL NUMBER / SPEC DECAL /- THREAD RIVET NUT HOT DECAL FUEL INDICATOR DECAL ENGINE COMPARTMENT DECAL NOTES:. Serial number decal. In the event the serial number decal becomes damaged or illegible, please contact your dealer to order a replacement.. EPA compliance decal.. Patent numbers decal. 760_07 -

10 Engine Guard _07

11 Engine Guard INDEX NO. PART NO. QTY. DESCRIPTION 5580 ENGINE GUARD (WITH DECAL) 605 H LOGO DECAL FW.5 X.06 X.090 SAE CS.500- X.5 HS G CS.500- X 5.00 HX G SHIELD NT.500- NL G SPACER PLASTIC WHEEL NT.75-6 HX G5 ZNY FW.06 X.8 X.060 SAE 0595 CB.75-6 X.99 G5 ZNY 698 HITCH NOTES: 760_07-5

12 Decals Models Ending in "US" INDEX NO. PART NO. QTY. DESCRIPTION SPARK ARRESTER DECAL 606 ANSI COMPLIANCE DECAL NOTES: _07

13 Section Hydraulic System Hydraulic Service Parts Steering Steering Box Assembly Brake _07 -

14 Hydraulic System _07

15 Hydraulic System INDEX NO. PART NO. QTY. DESCRIPTION 055 CS.500- X 5.00 HX G5 67 FW.50 X.5 X.87 SPL FW.06 X.8 X.060 SAE 0550 NT.75-6 HX G5 ZNY CS.500- X.75 HX G FW 0.5 X.8 X NT.500- UNT LK G8 ZN LS TRANSMISSION 6005 RS TRANSMISSION (NOT SHOWN) 9 06 CS.75-6 X.00 HX G IDLER SPRING MOUNT 780 TENSION SPRING CS.65- X.75 HX G " FLAT IDLER PULLEY IDLER PIVOT BUSHING GREASE FITTING STRAIGHT TENSIONER IDLER PIVOT BUSHING FW.5 X.06 X.09 SAE HRD ZN NT.500- HX G5 ZN NY BELT, A 6" EL NOTES:. Torque to 7 75 ft-lbs. The tensioner should pivot freely. 760_07 -

16 Hydraulic Service Parts 5 6 INDEX NO. PART NO. QTY. DESCRIPTION 60 SERVICE KIT, FAN 60 SERVICE KIT, BREATHER/DIPSTICK 606 FILTER 600 PLUG & O-RING ASSEMBLY SERVICE KIT, MOTOR SERVICE KIT, CONTROL ARM NOTES: - 760_07

17 This page intentionally left blank. 760_07-5

18 Steering WIRE HARNESS SWITCH LEADS LOCK COLLARS PUMP ROD _07

19 Steering INDEX NO. PART NO. QTY. DESCRIPTION 600 STEERING BOX ASSEMBLY SWITCH 7955 DAMPER 6087 PUMP ROD FW. X.687 X.05/.080H NT.- HX NL ZN HANDLE 8 06 CS.75-6 X.00 HX G FW.06 X.8 X.060 SAE CS.75-6 X.75 HX G5 789 BALL STUD 0550 NT.75-6 HX G5 ZNY LW. INT-EXT TOOTH 068 NT.-8 HX FLK ZNYC CAP LOCK NOTES: 760_07-7

20 Steering Box Assembly 5 5 A _07

21 Steering Box Assembly INDEX NO. PART NO. QTY. DESCRIPTION 6008 RS STEERING BOX SUB 6009 LS STEERING BOX SUB 07 NT.-8 HX G5 ZNYC 7685 FW. X.687 X.05/.080H BALL STUD NOTES: SERVICE PART A 886 STEERLEVER BUSHING 760_07-9

22 Steering Box Assembly _07

23 Steering Box Assembly INDEX NO. PART NO. QTY. DESCRIPTION BUSHING 7 STEERING COVER LOCK COLLAR ID FW.750 X.50 X.56 ZN 0 65 STEER PIVOT TUBE GM.50 X.00 X.75 X. NOTES: 760_07 -

24 Steering Box Assembly 5 A 6-760_07

25 Steering Box Assembly INDEX NO. PART NO. QTY. DESCRIPTION 0599 NT.500- HX JAM ZNYC SS /- X.50 SH ZNYC 607 X-ONEI DECAL MADE IN USA DECAL " WEAR TAPE NOTES: WEAR TAPE LENGTH A 5.5" ± 0." 760_07 -

26 Brake STEERING LEVER _07

27 Brake INDEX NO. PART NO. QTY. DESCRIPTION NT.75-6 HXZY NL FW.06 X.8 X.060 SAE 0550 NT.75-6 HX G5 ZNY FW. X.687 X.05/.080H NT.- HX NL ZN BUSHING BRAKE ROD ASSEMBLY LS BRAKE BELLCRANK RS BRAKE BELLCRANK (NOT SHOWN) CS.75-6 X.50 HX G BRAKE LINK TURNBUCKLE 0056 CS.75-6 X.75 HX G5 055 CS.75-6 X.50 HX G5 07 NT.-8 HX G5 ZNYC 5 79 LS BRAKE ARM 6 79 RS BRAKE ARM (NOT SHOWN) CS.-8 X.00 HX G BRAKE ASSEMBLY HUB ASSEMBLY (WITH STUDS) CS 0.-8 X 0.75 HS G8 FLANGE HEAD STUD, WHEEL LUG /-0 NOTES:. Included with the wheel motor.. Torque the nut to 00 ft-lbs.. Torque to 5 8 ft-lbs. 760_07-5

28 -6 760_07

29 Section Wheel & Tire Front Tire Breakdown Drive Wheel Breakdown _07 -

30 Wheel & Tire _07

31 Wheel & Tire INDEX NO. PART NO. QTY. DESCRIPTION CS.500- X.5 HX G5 ZN 67 FW.50 X.5 X.87 SPL 7976 FW.5 X.75 X.5 ZNY 78 BEARING SPACER 6 N/A FRONT WHEEL ASSEMBLY TIRE/WHEEL ASSEMBLY X 9.5 X (5" DECK) 6008 TIRE/WHEEL ASSEMBLY X X (60" DECK) WHEEL NUT. Torque to ft-lbs. NOTES: 760_07 -

32 Front Tire Breakdown _07

33 Front Tire Breakdown INDEX NO. PART NO. QTY. DESCRIPTION FORK 060 NT HX ZY NL 0596 FW.760 X.65 X.08 ZNYC 075 CS X 9.50 HX ZY TIRE/WHEEL ASSY X 6.50 SMOOTH 7778 TIRE/WHEEL ASSY X 6.50 RIBBED WHEEL BEARING BEARING SPACER VALVE STEM WHEEL, 6 X TIRE, X SMOOTH 777 TIRE, X RIBBED NOTES: 760_07-5

34 Drive Wheel Breakdown 6006 TIRE/WHEEL ASSEMBLY (5" MOWERS) INDEX NO. PART NO. QTY. DESCRIPTION 788 TIRE X WHEEL 095 VALVE STEM 6008 TIRE/WHEEL ASSEMBLY (60" MOWERS) INDEX NO. PART NO. QTY DESCRIPTION 785 TIRE X WHEEL 095 VALVE STEM NOTES: _07

35 Section 5 Engine, Kaw FX69V & FX70V (w/o Carbon Canister) Engine, Kaw FX69V & FX70V (with Carbon Canister) Fuel System S/N 0000 & Higher (w/o Carbon Canister) Fuel System S/N Prior to 0000 (w/o Carbon Canister) Fuel System (with Carbon Canister) Engine Service Parts, Kawasaki FX69V & FX70V Fuel Tank Service Parts _07 5-

36 Engine, Kaw FX69V & FX70V (w/o Carbon Canister) YEL/BLK PUR BLK RED/BLK 7 PUR 0A FUSE 5-760_07

37 Engine, Kaw FX69V & FX70V (w/o Carbon Canister) INDEX NO. PART NO. QTY. DESCRIPTION N/A KAWASAKI FX69V & FX70V ENGINE 7965 OIL DRAIN VALVE 06 CS.75-6 X.00 HX G FW.06 X.8 X.060 SAE LOOP CLAMP CABLE GUIDE CS M8 X.5 X 6 HX G NT.75-6 HX FLK ZNYC MUFFLER NT.-8 HX FLK ZNYC 0570 LOOP CLAMP FW. X.687 X.05/.080H 080 CS.-8 X.75 HX G CS.75-6 X.5 HX G5 P NT.-8 HX G5 ZNYC 6 96 CLUTCH ANCHOR WIRE TIE CS.-8 X.00 HX G KEY SINGLE ENGINE PULLEY 60785K CLUTCH KIT 795 CLUTCH HARNESS PIGTAIL FW.5 X. X.9 HRD CS.7-0 X.50 HX G5 P LW. INT-EXT TOOTH NEGATIVE BATTERY CABLE RED POSITIVE BATTERY CABLE NOTES:. Part of the wire harness.. Supplied with the engine.. Torque to 5 8 ft-lbs. Replace (do not reuse) the cap screw if it s removed or loosened. Use only hand tools to install this fastener.. Torque to 0 5 ft-lbs. Replace (do not reuse) the cap screw if it s removed or loosened. Use only hand tools to install this fastener. 5. Torque the nuts to ft-lbs. 760_07 5-

38 Engine, Kaw FX69V & FX70V (w/o Carbon Canister) SEAT SUPPORT VAPOR TEE FUEL VALVE A B _07

39 Engine, Kaw FX69V & FX70V (w/o Carbon Canister) INDEX NO. PART NO. QTY. DESCRIPTION " /" FUEL LINE " /6" VAPOR LINE 0 60 CLAMP 000 HOSE CLAMP NOTES: FUEL & VAPOR LINE LENGTHS A B 8" VALVE TO ENGINE (FUEL) " TEE TO ENGINE (VAPOR) 760_07 5-5

40 Engine, Kaw FX69V & FX70V (with Carbon Canister) YEL/BLK PUR BLK RED/BLK 7 PUR 0A FUSE _07

41 Engine, Kaw FX69V & FX70V (with Carbon Canister) INDEX NO. PART NO. QTY. DESCRIPTION N/A KAWASAKI FX69V & FX70V ENGINE 7965 OIL DRAIN VALVE 06 CS.75-6 X.00 HX G FW.06 X.8 X.060 SAE LOOP CLAMP CABLE GUIDE CS M8 X.5 X 6 HX G NT.75-6 HX FLK ZNYC MUFFLER NT.-8 HX FLK ZNYC 0570 LOOP CLAMP FW. X.687 X.05/.080H 080 CS.-8 X.75 HX G CS.75-6 X.5 HX G5 P NT.-8 HX G5 ZNYC 6 96 CLUTCH ANCHOR WIRE TIE CS.-8 X.00 HX G KEY SINGLE ENGINE PULLEY 60785K CLUTCH KIT 795 CLUTCH HARNESS PIGTAIL FW.5 X. X.9 HRD CS.7-0 X.50 HX G5 P LW. INT-EXT TOOTH NEGATIVE BATTERY CABLE RED POSITIVE BATTERY CABLE NOTES:. Part of the wire harness.. Supplied with the engine.. Torque to 5 8 ft-lbs. Replace (do not reuse) the cap screw if it is removed or loosened. Use only hand tools to install this fastener.. Torque to 0 5 ft-lbs. Replace (do not reuse) the cap screw if it is removed or loosened. Use only hand tools to install this fastener. 5. Torque the nuts to ft-lbs. 760_07 5-7

42 Engine, Kaw FX69V & FX70V (with Carbon Canister) FUEL VALVE SEAT SUPPORT 9 9 A B _07

43 Engine, Kaw FX69V & FX70V (with Carbon Canister) INDEX NO. PART NO. QTY. DESCRIPTION " /" FUEL LINE " /6" VAPOR LINE HOSE CLAMP 60 CLAMP, /6" HOSE CLAMP NOTES: FUEL LINE LENGTH A B 8" VALVE TO ENGINE (FUEL) " CANISTER TO ENGINE (VAPOR) 760_07 5-9

44 Fuel System S/N 0000 & Higher (w/o Carbon Canister) 7 A 6 D 5 B C E F _07

45 Fuel System S/N 0000 & Higher (w/o Carbon Canister) INDEX NO. PART NO. QTY. DESCRIPTION RATCHETING GAS CAP,.5" RS FUEL TANK ASSEMBLY (S/N 00 & HIGHER) 6050 RS FUEL TANK ASSEMBLY (S/N 0000 TO 00) LS FUEL TANK ASSEMBLY (S/N 00 & HIGHER) 605 LS FUEL TANK ASSEMBLY (S/N 0000 TO 00) " /" FUEL LINE PLASTIC TEE, /6" HOSE CLAMP " /6" VAPOR LINE FUEL VALVE -WAY 9 60 VAPOR SYSTEM FILTER CS.-8 X.00 HX G FW. X.687 X.05/.080H 0570 LOOP CLAMP 068 NT.-8 HX FLK ZNYC FW.06 X.00 X. HRD Z CS.75-6 X.75 HX G CS.50-0 X.50 HX G FW.8 X.65 X.05/.080H COVER PANEL NOTES: FUEL & VAPOR LINE LENGTHS A B C D E F 6" RIGHT TANK TO TEE (VAPOR) 0" TEE TO TEE (VAPOR) 8" LEFT TANK TO TEE (VAPOR) 8" RIGHT TANK TO VALVE (FUEL) 9" LEFT TANK TO VALVE (FUEL) 5" TEE TO FILTER (VAPOR). Torque to 0 ft-lbs. 760_07 5-

46 Fuel System S/N Prior to 0000 (w/o Carbon Canister) A 6 D 5 B 5 C E F _07

47 Fuel System S/N Prior to 0000 (w/o Carbon Canister) INDEX NO. PART NO. QTY. DESCRIPTION RATCHETING GAS CAP,.5" 6087 RS FUEL TANK ASSEMBLY 6088 LS FUEL TANK ASSEMBLY " /" FUEL LINE PLASTIC TEE /" X /" X /6" HOSE CLAMP " /6" VAPOR LINE FUEL VALVE -WAY 9 60 VAPOR SYSTEM FILTER CS.-8 X.00 HX G FW. X.687 X.05/.080H 0570 LOOP CLAMP 068 NT.-8 HX FLK ZNYC FW.06 X.00 X. HRD Z CS.75-6 X.75 HX G CS.50-0 X.50 HX G FW.8 X.65 X.05/.080H COVER PANEL NOTES: FUEL & VAPOR LINE LENGTHS A B C D E F 6" RIGHT TANK TO TEE (VAPOR) 0" TEE TO TEE (VAPOR) 8" LEFT TANK TO TEE (VAPOR) 8" RIGHT TANK TO VALVE (FUEL) 9" LEFT TANK TO VALVE (FUEL) 5" TEE TO FILTER (VAPOR). Torque to 0 ft-lbs. 760_07 5-

48 Fuel System (with Carbon Canister) 7 A C 7 B 6 5 E D _07

49 Fuel System (with Carbon Canister) INDEX NO. PART NO. QTY. DESCRIPTION RATCHETING GAS CAP,.5" RS FUEL TANK ASSEMBLY 6050 RS FUEL TANK ASSEMBLY (S/N PRIOR TO 00) LS FUEL TANK ASSEMBLY 605 LS FUEL TANK ASSEMBLY (S/N PRIOR TO 00) " /" FUEL LINE PLASTIC TEE, /6" HOSE CLAMP " /6" VAPOR LINE FUEL VALVE -WAY CS.-8 X.00 HX G FW. X.687 X.05/.080H 0570 LOOP CLAMP 068 NT.-8 HX FLK ZNYC 080 CS.-8 X.75 HX G " CUSHIONED CLAMP FW.06 X.00 X. HRD Z CS.75-6 X.75 HX G CARBON CANISTER COVER PANEL CS.50-0 X.50 HX G FW.8 X.65 X.05/.080H NOTES: FUEL & VAPOR LINE LENGTHS A B C D E 6" RIGHT TANK TO TEE (VAPOR) 8" LEFT TANK TO TEE (VAPOR) 8" RIGHT TANK TO VALVE (FUEL) 9" LEFT TANK TO VALVE (FUEL) " TEE TO CANISTER (VAPOR). Torque to 0 ft-lbs.. Included on the engine page. 760_07 5-5

50 Engine Service Parts, Kawasaki FX69V & FX70V 5 INDEX NO. PART NO. QTY. DESCRIPTION 7856 MAIN AIR FILTER SAFETY AIR FILTER 6058 OIL FILTER IN-LINE FUEL FILTER VACUATOR VALVE NOTES: _07

51 Fuel Tank Service Parts INDEX NO. PART NO. QTY. DESCRIPTION 6099 VENT FITTING 6000 GROMMET SUCTION HOSE GROMMET 6057 SUCTION HOSE 9.5" FUEL GAUGE ASSEMBLY & GROMMET FUEL DIAL GROMMET NOTES: 760_07 5-7

52 _07

53 Section 6 Battery Instrument Panel _07 6-

54 Battery _07

55 Battery INDEX NO. PART NO. QTY. DESCRIPTION CS.50-0 X.5 HX ZNYC FW.8 X.65 X.05/.080 HD ZN/YL 7 BATTERY STRAP 097 NT.50-0 HX G5 ZNYC LW.50 INT-EXT TOOTH Z CS.50-0 X.75 HX G RED BATTERY CABLE BOOT CS.-8 X.75 HX G RS BATTERY CABLE BRACKET FW. X.687 X.05/.080H 07 NT.-8 HX G5 ZNYC 7005 LS BATTERY CABLE BRACKET 000 WIRE TIE (NOT SHOWN) NOTES: 760_07 6-

56 Instrument Panel A 0A FUSES 8 ORG YEL/ BLK ORG BLK _07

57 Instrument Panel INDEX NO. PART NO. QTY. DESCRIPTION CHOKE CABLE PTO SWITCH KEY ASSEMBLY IGNITION SWITCH HOUR METER RED INDICATOR LIGHT IGNITION CONTROLLER NT #0- HX NL ZN CB 0- X.50 ZYNC INSTRUMENT PANEL (WITH DECAL) 0698 CS 0- X.75 HX FLK ZN 709 FW.9 X.50 X.08 ZNYC 6009 THROTTLE CABLE CS.50-0 X.50 HX G FW.8 X.65 X.05/.080H INSTRUMENT PANEL DECAL WIRE TIE CS.-8 X.75 HX G FW. X.687 X.05/.080H LOOP CLAMP 07 NT.-8 HX G5 ZNYC 6080 WIRE HARNESS WIRE TIE 05 CLUTCH CONNECTOR REPAIR KIT. Part of the wire harness. NOTES: 760_07 6-5

58 _07

59 Section 7 5" Service Deck " Deck Pulleys & Spindles " Deck " Service Deck " Deck Pulleys & Spindles " Deck Deck Lift Deck Mounting Hardware _07 7-

60 5" Service Deck _07

61 5" Service Deck INDEX NO. PART NO. QTY. DESCRIPTION " DECK (WITH DECALS & HARDWARE) CN.-8 X.0 MAX THK /6-8 THREAD RIVET NUT 6087 DECK DANGERS DECAL DISCHARGE CHUTE DECAL BELT ROUTING DECAL " DECK DECAL THROWN OBJECTS DECAL NOTES: 760_07 7-

62 5" Deck Pulleys & Spindles _07

63 5" Deck Pulleys & Spindles INDEX NO. PART NO. QTY. DESCRIPTION 796 CS.65- X.50 HX G5 7 DECK BELT IDLER GUIDE FW.65 X.00 X. ZNYC DUST SHIELD WITH OFFSET IDLER PULLEY NHI 5.0" DECK IDLER SLIDE TENSION SPRING CHAIN, LINK CS.-8 X.50 FLT SH ZY 0 60 UHMW IDLER SLIDE 7885 IDLER PULLEY NHI 6.0" CS.500- X.5 HX G5 ZN 7586 CW.55 X.5 X.0 BLK B-SEC 5. EOD PULLEY NT.500- HX G5 ZNYC FW.5 X.06 X.090 SAE 7 7 KEY / SQ X BLADE SPINDLE CS.500- X.50 HX G FW. X.687 X.05/.080H NT.-8 HX ZY NL 608 CB.500- X 7.50 STD ZN 60 SPACER PLASTIC WHEEL NT.500- HX G8 ZY NL PLASTIC WHEEL SPACER CB.500- X.50 STD ZN. Torque to ft-lbs. NOTES: 760_07 7-5

64 5" Deck Pulleys & Spindles INDEX NO. PART NO. QTY. DESCRIPTION GREASE FITTING STRAIGHT 0 79 PUSHER 695 PLATED PIVOT TUBE 066 CS.-8 X.00 HX G5 NOTES: _07

65 This page intentionally left blank. 760_07 7-7

66 5" Deck _07

67 5" Deck INDEX NO. PART NO. QTY. DESCRIPTION 8 RS PULLEY COVER 85 LS PULLEY COVER 7900 KNOB 5/6-8 X /" 60 CHUTE PIN TORSION SPRING DISCHARGE CHUTE NT.75-6 HX ZY NL BELT, B 5" EL BLADE, 7.86"-H-F-CW 7875 BLADE, 7.86"-L-F-CW 7856 BLADE, 7.86"-GAT-F-CW 7998 BLADE, 7.86"-MUL-F-CW BLADE, F7.86"-H-F-CW CW.6 X.5 X.87 PNT 7887 CS.65- X.5 HX G5 Z NOTES:. Do not torque the nut; the discharge chute must pivot freely.. Torque to 8 ft-lbs. 760_07 7-9

68 60" Service Deck _07

69 60" Service Deck INDEX NO. PART NO. QTY. DESCRIPTION " DECK (WITH DECALS & HARDWARE) CN.-8 X.0 MAX THK /6-8 THREAD RIVET NUT 6087 DECK DANGERS DECAL DISCHARGE CHUTE DECAL BELT ROUTING DECAL " DECK DECAL THROWN OBJECTS DECAL NOTES: 760_07 7-

70 60" Deck Pulleys & Spindles _07

71 60" Deck Pulleys & Spindles INDEX NO. PART NO. QTY. DESCRIPTION 796 CS.65- X.50 HX G5 7 DECK BELT IDLER GUIDE FW.65 X.00 X. ZNYC DUST SHIELD WITH OFFSET IDLER PULLEY NHI 6.0" DECK IDLER SLIDE TENSION SPRING 8 79 CHAIN, LINK CS.-8 X.50 FLT SH ZY 0 60 UHMW IDLER SLIDE CS.500- X.5 HX G5 ZN 7586 CW.55 X.5 X.0 BLK 7708 DECK DRIVE PULLEY 0089 NT.500- HX G5 ZNYC FW.5 X.06 X.090 SAE 6 7 KEY / SQ X BLADE SPINDLE CS.500- X.50 HX G FW. X.687 X.05/.080H NT.-8 HX ZY NL 608 CB.500- X 7.50 STD ZN 60 SPACER PLASTIC WHEEL NT.500- HX G8 ZY NL PLASTIC WHEEL SPACER CB.500- X.50 STD ZN. Torque to ft-lbs. NOTES: 760_07 7-

72 60" Deck Pulleys & Spindles INDEX NO. PART NO. QTY. DESCRIPTION 8 79 PUSHER GREASE FITTING STRAIGHT PLATED PIVOT TUBE 066 CS.-8 X.00 HX G5 NOTES: 7-760_07

74 60" Deck _07

75 60" Deck INDEX NO. PART NO. QTY. DESCRIPTION 8 RS PULLEY COVER 8 LS PULLEY COVER 7900 KNOB 5/6-8 X /" 60 CHUTE PIN TORSION SPRING DISCHARGE CHUTE NT.75-6 HX ZY NL BELT, B 65.56" EL BLADE, 0.95".09" HS CW 7980 BLADE, 0.95" MUL-F-CW BLADE, 0.95" GAT-F-CW 7955 BLADE, F0.95"-H-F-CW CW.6 X.5 X.87 PNT 7887 CS.65- X.5 HX G5 Z NOTES:. Do not torque the nut; the discharge chute must pivot freely.. Torque to 8 ft-lbs. 760_07 7-7

76 Deck Lift _07

77 Deck Lift INDEX NO. PART NO. QTY. DESCRIPTION 6007 DECK HEIGHT PIN E CLIP.00 X.65 X STOP HANDLE 789 CE.750 X.5 X.75 HEAD DECK LIFT INDICATOR CS.7- X.75 HX G DECK LIFT CHAIN NT.7- HX FLG ZN DECK LIFT SPRING GREASE FITTING STRAIGHT CS.-8 X.50 FLTHR HX 07 NT.-8 HX G5 ZNYC 858 DECK LEVELER YOKE 7078 FW.65 X.50 X.05 ZN CS.65- X.5 HX G5 Z CS.7- X.75 FULTH NOTES: 760_07 7-9

78 Deck Mounting Hardware _07

79 Deck Mounting Hardware INDEX NO. PART NO. QTY. DESCRIPTION FW.760 X.65 X.08 ZNYC CS X.00 HX G NT HX ZY NL NOTES: 760_07 7-

80 7-760_07

81 Section 8 Seat, Deluxe Seat Service Parts, Deluxe ROPS S/N 050 & Higher ROPS S/N Prior to _07 8-

82 8-760_07 Seat, Deluxe

83 Seat, Deluxe INDEX NO. PART NO. QTY. DESCRIPTION DELUXE SEAT 5507 SEAT PAN (WITH DECAL & INSTALLATION KIT) 9 SEAT LATCH 7890 TORSION SPRING BATTERY WARNINGS DECAL 6 7 SEAT STOP CB.-8 X.75 FUL ZN FW. X.687 X.05/.080H 9 07 NT.-8 HX G5 ZNYC FW.06 X.8 X.060 SAE NT.75-6 HX ZY NL 7558 SB.75 X.75 SH NT.-8 HX ZY NL 000 WIRE TIE ARMREST WARNING DECAL FW. X.00 X. HRD Z FIBER WASHER 8 50 SEAT PAN STOP 9 06 CS.75-6 X.00 HX G RS FRAME COVER (WITH DECAL) 7850 RS STEERING DECAL VIBRATION MOUNT 7859 LS STEERING DECAL LS FRAME COVER (WITH DECAL) PUMP BELT WARNING DECAL CN.-8 X.0 MAX THK NT.75-6 HX G5 ZNY 8 FLOOR PLATE CS.-8 X.00 HX G CS.75-6 X.5 HX G5 ZN NOTES:. Do not torque; the seat pan and seat pan stop must pivot freely. 760_07 8-

84 Seat Service Parts, Deluxe 6 5 INDEX NO. PART NO. QTY. DESCRIPTION 6060 ARMREST KIT 6069 BACK SEAT COVER 6069 BOTTOM SEAT COVER 608 SEAT SWITCH STANDARD SEAT TRACK KIT 6 60 SEAT BELT KIT 8-760_07

86 ROPS S/N 050 & Higher _07

87 ROPS S/N 050 & Higher INDEX NO. PART NO. QTY. DESCRIPTION ROPS SUB-ASSEMBLY (WITH DECAL) 6065 ROPS DECAL 068 CS.500- X.50 HX G FW.5 X.06 X.090 SAE 5 07 NT.500- UNT LK G8 ZN KIT, ROPS HARDWARE NOTES:. Torque to 7 ft-lbs.. The hardware for the ROPS is sold as a kit. 760_07 8-7

88 ROPS S/N Prior to _07

89 ROPS S/N Prior to 050 INDEX NO. PART NO. QTY. DESCRIPTION 6080 ROPS KIT (WITH DECALS, HARDWARE & SEATBELT) 6070 HAND KNOB 607 LYNCH PIN W/ LANYARD 068 CS.500- X.50 HX G NT.500- UNT LK G8 ZN ROPS STOP CS.500- X.5 HX G FW.5 X.06 X.090 SAE ROPS DECAL. Torque to 7 ft-lbs. NOTES: 760_07 8-9

90 _07