Product Catalog. Marine and Offshore Cables Bostrig Type P, Bostrig VFD and Fiber Optic Marine Rated Cables

Transcription

1 Product Catalog Marine and Offshore Cables Bostrig P, Bostrig VFD and Fiber Optic Marine Rated Cables

2

3 Table of Contents Bostrig 125 P Control 12 and 10 AWG (unarmored)... 1 Bostrig 125 P Control 12 and 10 AWG (armored & sheathed)...4 Bostrig 125 P Control 14 AWG (unarmored)...7 Bostrig 125 P Control 14 AWG (armored & sheathed) Bostrig 125 P Control 16 AWG (unarmored) Bostrig 125 P Control 16 AWG (armored & sheathed) Bostrig 125 P Control 18 AWG (unarmored) Bostrig 125 P Control 18 AWG (armored & sheathed)...22 Bostrig 125 P MR Power Cable (armored & sheathed & unarmored)...25 Bostrig 125 P Power 1C (unarmored) Bostrig 125 P Power 1C (armored & sheathed) Bostrig 125 P Power 2C (unarmored) Bostrig 125 P Power 2C (armored & sheathed)...37 Bostrig 125 P Power 3C (unarmored) Bostrig 125 P Power 3C (armored & sheathed)...43 Bostrig 125 P Power 4C (unarmored) Bostrig 125 P Power 4C (armored & sheathed)...49 Bostrig 125 P Power 5C (unarmored)...52 Bostrig 125 P Power 5C (armored & sheathed)...55 Bostrig 125 P Signal OS 20, 18, and 16 AWG (unarmored) Bostrig 125 P Signal OS 20, 18, and 16 AWG (armored & sheathed) Bostrig 125 P Signal IO P 16 and 14 AWG (unarmored) Bostrig 125 P Signal IO P 16 and 14 AWG (armored & sheathed)...67 Bostrig 125 P Signal IO P 20 and 18 AWG (unarmored)...70 Bostrig 125 P Signal IO P 20 and 18 AWG (armored & sheathed)...73 Bostrig 125 P Signal IO T 18 and 16 AWG (unarmored)...76 Bostrig 125 P Signal IO T 18 and 16 AWG (armored & sheathed)...79 Bostrig 125 P VFD 2kV (unarmored)...82 S611 T Marine Fiber Optic Cables (unarmored)...85 S670 T Marine Fiber Optic Cables (armored & sheathed)...87 QFCI Fire Resistant Marine Fiber Optic Cables REFERENCES Table 1 TIA/EIA Fiber Optic Color Codes Table 2 Bostrig Conductor Information This catalog represents only a partial selection of International wire and cable products, based on criteria submitted when requesting the information. For a complete list of International products, including specialty conversion and termination items, website : na.prysmiangroup.com/oil-gas All products are subject to current availability. Please check with your International representative. All contents International. All rights reserved. II

4 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 12 & 10 AWG Applications Bostrig P Marine and Offshore Cable is primarily designed for power, control, signal, and instrumentation applications for offshore and land drilling rigs, marine vessels, and offshore production facilities. Bostrig cables have excellent resistance to oil, abrasion, moisture, vibration, sunlight, and ester based mud ( P- MR). They are suitable for use in Class 1, Division 1 offshore applications (armored & sheathed). The standard insulation has a continuous operating temperature of 125 C, allowing for higher ampacity levels. These cables also meet cold bend requirements of -40 C and cold impact of -35 C (CSA 22.2 N0. 0.3). This product may be manufactured in an unarmored or armored and sheathed version. Features/Ratings - Superior resistance to oil, abrasion, moisture, sunlight, crush and impact - High strand count conductors provide superior flexibility - Higher allowable conductor operating temperature results in increased ampacity - Cold bend/ cold impact of -40 / -35 C in accordance with CSA 22.2 No Flame retardant in accordance with IEEE 1202 and IEC Category A - Meets IEEE standards for 600V and performance requirements of IEC standards for 0.6/1 kv - cables suitable for use in Class I Division 2 and Zone 2 hazardous locations - Meets the requirements of UL 1277 and UL 1569 for TC-ER exposed runs Approvals IEEE 1580 and IEEE 45- Marine Shipboard Cable UL Marine Shipboard Cable X110 CSA 22.2 No Marine Shipboard Cable X110 CSA 22.2 No CIC CSA 22.2 No TC-ER Det Norske Veritas (DNV) American Bureau of Shipping (ABS) Transport Canada Approved AMS Transport Canada Lloyd s Register of Shipping (LRS) United States Coast Guard-46CFR Construction CONDUCTOR: Soft annealed stranded tinned copper per ASTM B 33. A polyester tape separator is used over the conductor. INSULATION: Bostrig P chemically cross-linked polyolefin (XLPO), meeting IEEE JACKET: Flame-Retardant thermosetting CPE (Chlorinated Polyethylene) in accordance with the requirements of IEEE as shown in tables on opposite page. Arctic Neoprene ( N) also available as an option. 1

5 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 12 & 10 AWG 12 AWG 3.08 mm 2 of Conductor Insulation Sheath Cable Diameter Cable Weight in mm in mm in mm Lbs/Mft Kg/Km C12PN C12PN C12PN C12PN C12PN C12PN C12PN C12PN C12PN C12PN C12PN ,125 C12PN ,325 C12PN ,070 1,590 C12PN ,295 1,925 C12PN ,540 2,290 C12PN ,035 3,030 C12PN ,130 4, AWG 5.53 mm 2 of Conductor Insulation Sheath Cable Diameter Cable Weight in mm in mm in mm Lbs/Mft Kg/Km C10PN C10PN C10PN C10PN C10PN C10PN C10PN C10PN The current limit on these cables should be for providing control functions through relays and switching devices. The maximum current for any one conductor should not exceed the value Table 3 for three conductor cables. The average of all conductors should not exceed the limit based on the total number of conductors in the cable taken from Table 4 multiplied by the ampacity from Table 3. Three conductor or four conductor cables with three current carrying conductors may be used for continuous power. This information is provided for reference only. Please consult the factory or your representative to confirm all engineering information. This information is not intended to replace the information in the appropriate and applicable standard or code. Ampacity based on 45 C ambient temperature; 95 C values based on ABS MODU Rules Table C values based on IEEE C values based on API 14F. TABLE 3 Three Conductor Cable, Four Conductor Cables with Three Current Carrying Conductors 45ºC Ambient Conductor Size Gauge CMA mm 2 95ºC 100ºC 110ºC 125ºC* 12 6, , *125 C ampacities based on 45 C ambient in free air. Consult factory for conditions of use. TABLE 4 Cables with more than Four Current Carrying Conductors of Conductors % of 3 Conductor Ampacity Values and greater 30 2

6 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 12 & 10 AWG 12 AWG 3.08 mm 2 GLAND SELECTION GLAND REFERENCE CHART in mm (metric) (NPT) () Hub Size Reference () - NPT Thread Size Reference C12PN UB AB-52/ NE-04/ 05/ = 1/2" 03 = 1/2" - 14 NPT C12PN UB AB-52/ NE-04/ 05/ = 1/2" 04 = 1/2" - 14 NPT C12PN UB AB-53/ NE-05/ 08/ 10/ = 3/4" 05 = 1/2" - 14 NPT C12PN UB-02/ AB-53/ NE-05/ 08/ 10/ = 1" 08 = 3/4" - 14 NPT C12PN UB-02/ AB-53/ NE-05/ 08/ 10/ = 1-1/4" 10 = 3/4" - 14 NPT C12PN UB-02/ AB-53/ NE-05/ 08/ 10/ = 1-1/2" 14 = 1" /2 NPT C12PN UB AB-53/ NE-05/ 08/ 10/ = 2" 15 = 1" /2 NPT C12PN UB-03/ AB-55/ NE-10/ 14/ 15/ = 2-1/2" 20 = 1 1/4" /2 NPT C12PN UB AB-55/ NE-10/ 14/ 15/ = 3" 21 = 1 1/4" /2 NPT C12PN UB AB NE-15/ = 3-1/2" 27 = 1 1/2" /2 NPT C12PN UB-04/ 05/ AB-56/ NE-15/ 20/ 21/ = 2" /2 NPT C12PN UB-05/ AB NE-21/ = 2 1/2" - 8 NPT C12PN UB-05 /15/ AB NE-21/ = 3" - 8 NPT C12PN UB-05/ 15/ AB-57/ NE-21/ 27/ = 3" - 8 NPT C12PN UB AB NE-32 C12PN UB AB NE-32 C12PN UB AB NE AWG 5.53 mm 2 GLAND SELECTION in mm (metric) (NPT) C10PN UB AB-53/ NE-05/ 08/ 10/ 14 C10PN UB AB-53/ NE-05/ 08/ 10/ 14 C10PN UB-02/ AB-53/ NE-05/ 08/ 10/ 14 C10PN UB AB-53/ NE-05/ 08/ 10/ 14 C10PN UB-03/ AB NE-10/ 14 C10PN UB-03/ AB NE-10/ 14 C10PN UB-03/ AB NE-10/ 14 C10PN UB AB NE-15/ 20 3

7 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / armored and sheathed TYPE P CONTROL CABLE 600V or 0.6/1kV 12 & 10 AWG Applications Bostrig P Marine and Offshore Cable is primarily designed for power, control, signal, and instrumentation applications for marine vessels, offshore and land drilling rigs, and offshore production facilities. Bostrig cables have excellent resistance to oil, abrasion, moisture, vibration, sunlight, and ester based mud ( P- MR). They are suitable for use in Class 1, Division 1 offshore applications (armored and sheathed). The standard insulation has a continuous operating temperature of 125 C, allowing for higher ampacity levels. These cables also meet cold bend requirements of -40 C and cold impact of -35 C (CSA 22.2 N0. 0.3). This product may be manufactured in an unarmored or armored and sheathed version. Features/Ratings - Superior resistance to oil, abrasion, moisture, sunlight, crush and impact - High strand count conductors provide superior flexibility - Higher allowable conductor operating temperature results in increased ampacity - Cold bend/ cold impact of -40 /-35 C in accordance with CSA 22.2 No Flame retardant in accordance with IEEE 1202 and IEC Category A - Meets IEEE standards for 600V and performance requirements of IEC standards for 0.6/1 kv - and sheathed cables suitable for use in Class 1 Division 1 and Zone 1 hazardous locations offshore Approvals IEEE 1580 and IEEE 45- Marine Shipboard Cable UL Marine Shipboard Cable X110 CSA 22.2 No Marine Shipboard Cable X110 Det Norske Veritas (DNV) American Bureau of Shipping (ABS) Transport Canada Approved AMS Transport Canada Lloyd s Register of Shipping (LRS) United States Coast Guard-46CFR Construction CONDUCTOR: Soft annealed stranded tinned copper per ASTM B 33. A polyester tape separator is used over the conductor. INSULATION: Bostrig P chemically cross-linked polyolefin (XLPO), meeting IEEE JACKET: Flame-Retardant Thermosetting CPE (Chlorinated Polyethylene) in accordance with the requirements of IEEE as shown in tables on opposite page. Arctic Neoprene ( N) also available as an option. ARMOR: Braided bronze in accordance with IEEE SHEATH: Flame-Retardant Thermosetting CPE (Chlorinated Polyethylene) applied over the armor in accordance with the requirements of IEEE as shown in tables on opposite page. Arctic Neoprene ( N) also available as an option. 4

8 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / armored and sheathed TYPE P CONTROL CABLE 600V or 0.6/1kV 12 & 10 AWG 12 AWG 3.08 mm 2 of Conductor Insulation Sheath Cable Diameter Cable Weight in mm in mm in mm Lbs/Mft Kg/Km C12PNBS-2 T C12PNBS-3 T C12PNBS-4 T C12PNBS-5 T C12PNBS-6 T C12PNBS-7 T C12PNBS-8 T C12PNBS-10 T ,005 C12PNBS-12 T ,070 C12PNBS-16 T ,420 C12PNBS-20 T ,135 1,690 C12PNBS-24 T ,310 1,950 C12PNBS-30 T ,495 2,225 C12PNBS-37 T ,765 2,625 C12PNBS-44 T ,100 3,125 C12PNBS-60 T ,770 4,120 C12PNBS-91 T ,045 6, AWG 5.53 mm 2 of Conductor Insulation Sheath Cable Diameter The current limit on these cables should be for providing control functions through relays and switching devices. The maximum current for any one conductor should not exceed the value Table 3 for three conductor cables. The average of all conductors should not exceed the limit based on the total number of conductors in the cable taken from Table 4 multiplied by the ampacity from Table 3. Three conductor or four conductor cables with three current carrying conductors may be used for continuous power. This information is provided for reference only. Please consult the factory or your representative to confirm all engineering information. This information is not intended to replace the information in the appropriate and applicable standard or code. Ampacity based on 45 C ambient temperature; 95 C values based on ABS MODU Rules Table C values based on IEEE C values based on API 14F. Cable Weight in mm in mm in mm Lbs/Mft Kg/Km C10PNBS-2 T C10PNBS-3 T C10PNBS-4 T C10PNBS-5 T C10PNBS-6 T C10PNBS-7 T C10PNBS-8 T ,055 C10PNBS-10 T ,415 TABLE 3 Three Conductor Cable, Four Conductor Cables with Three Current Carrying Conductors 45ºC Ambient Conductor Size Gauge CMA mm 2 95ºC 100ºC 110ºC 125ºC* 12 6, , *125 C ampacities based on 45 C ambient in free air. Consult factory for conditions of use. TABLE 4 Cables with more than Four Current Carrying Conductors of Conductors % of 3 Conductor Ampacity Values and greater 30 5

9 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / armored and sheathed TYPE P CONTROL CABLE 600V or 0.6/1kV 12 & 10 AWG 12 AWG 3.08 mm 2 GLAND SELECTION GLAND REFERENCE CHART in mm (metric) (NPT) () Hub Size Reference () - NPT Thread Size Reference C12PNBS-2 T AN-02/ SW NP-04/ = 1/2" 03 = 1/2" - 14 NPT C12PNBS-3 T AN-02/ SW NP-05/ = 3/4" 04 = 1/2" - 14 NPT C12PNBS-4 T AN-02/ 03/ 10/ SW NP-05/ = 1" 07 = 3/4" - 14 NPT C12PNBS-5 T AN-02/ 03/ 10/ SW NP-05/ = 1-1/4" 05 = 1/2" - 14 NPT C12PNBS-6 T AN-03/ SW NP-10/ = 1-1/2" 08 = 3/4" - 14 NPT C12PNBS-7 T AN-03/ SW NP-10/ = 2" 10 = 3/4" - 14 NPT C12PNBS-8 T AN-03/ SW NP-10/ = 2-1/2" 14 = 1" /2 NPT C12PNBS-10 T AN-04/ SW NP-10/ = 3" 15 = 1" /2 NPT C12PNBS-12 T AN-04/ SW NP-10/ = 3-1/2" 20 = 1-1/4" /2 NPT C12PNBS-16 T AN-04/ SW NP-15/ = 1/2" 21 = 1-1/4" /2 NPT C12PNBS-20 T AN-04/ 05/ SW NP-15/ = 3/4" 27 = 1-1/2" /2 NPT C12PNBS-24 T AN SW NP-21/ = 1" 28 = 1-1/2" /2 NPT C12PNBS-30 T AN SW NP-21/ = 2" /2 NPT C12PNBS-37 T AN-05/ SW NP-21/ = 2" /2 NPT C12PNBS-44 T AN SW NP-28/ = 2" /2 NPT C12PNBS-60 T AN SW NP = 2-1/2" - 8 NPT C12PNBS-91 T AN SW-60/ NP-33/ = 2-1/2" - 8 NPT 45 = 3" - 8 NPT 47 = 3" - 8 NPT 10 AWG 5.53 mm 2 GLAND SELECTION in mm (metric) (NPT) C10PNBS-2 T AN-03/ SW NP-05/ 08 C10PNBS-3 T AN-03/ SW NP-05/ 08 C10PNBS-4 T AN-03/ SW NP-10/ 14 C10PNBS-5 T AN-03/ SW NP-10/ 14 C10PNBS-6 T AN-03/ SW NP-10/ 14 C10PNBS-7 T AN-03/ SW NP-10/ 14 C10PNBS-8 T AN-04/ SW NP-10/ 14 C10PNBS-10 T AN-04/ SW NP-15/ 20 6

10 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 14 AWG Applications Bostrig P Marine and Offshore Cable is primarily designed for power, control, signal, and instrumentation applications for offshore and land drilling rigs, marine vessels, and offshore production facilities. Bostrig cables have excellent resistance to oil, abrasion, moisture, vibration, sunlight, and ester based mud ( P- MR). They are suitable for use in Class 1, Division 1 offshore applications (armored and sheathed). The standard insulation has a continuous operating temperature of 125 C, allowing for higher ampacity levels. These cables also meet cold bend requirements of -40 C and cold impact of -35 C (CSA 22.2 N0. 0.3). This product may be manufactured in an unarmored or armored and sheathed version. Features/Ratings - Superior resistance to oil, abrasion, moisture, sunlight, crush and impact - High strand count conductors provide superior flexibility - Higher allowable conductor operating temperature results in increased ampacity - Cold bend/ cold impact of -40 / -35 C in accordance with CSA 22.2 No Flame retardant in accordance with IEEE 1202 and IEC Category A - Meets IEEE standards for 600V and performance requirements of IEC standards for 0.6/1 kv - cables suitable for use in Class I Division 2 and Zone 2 hazardous locations - Meets the requirements of UL 1277 and UL 1569 for TC-ER exposed runs Approvals IEEE 1580 and IEEE 45- Marine Shipboard Cable UL Marine Shipboard Cable X110 CSA 22.2 No Marine Shipboard Cable X110 CSA 22.2 No CIC CSA 22.2 No. 230 as TC-ER Det Norske Veritas (DNV) American Bureau of Shipping (ABS) Transport Canada Approved AMS Transport Canada Lloyd s Register of Shipping (LRS) United States Coast Guard-46CFR Construction CONDUCTOR: Soft annealed stranded tinned copper per ASTM B 33. A polyester tape separator is used over the conductor. INSULATION: Bostrig P chemically cross-linked polyolefin (XLPO), meeting IEEE JACKET: Flame-Retardant thermosetting CPE (Chlorinated Polyethylene) in accordance with the requirements of IEEE as shown in tables on opposite page. Arctic Neoprene ( N) also available as an option. 7

11 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 14 AWG 14 AWG / 600V or 0.6/1kV 1.94 mm 2 of Conductor Insulation Sheath Cable Diameter Cable Weight in mm in mm in mm Lbs/Mft Kg/Km C14PN-2 T C14PN-3 T C14PN-4 T C14PN-5 T C14PN-6 T C14PN-7 T C14PN-8 T C14PN-10 T C14PN-12 T C14PN-16 T C14PN-20 T C14PN-24 T C14PN-30 T ,155 C14PN-37 T ,385 C14PN-44 T ,105 1,645 C14PN-60 T ,455 2,165 C14PN-91 T ,145 3,190 The current limit on these cables should be for providing control functions through relays and switching devices. The maximum current for any one conductor should not exceed the value Table 3 for three conductor cables. The average of all conductors should not exceed the limit based on the total number of conductors in the cable taken from Table 4 multiplied by the ampacity from Table 3. Three conductor or four conductor cables with three current carrying conductors may be used for continuous power. This information is provided for reference only. Please consult the factory or your representative to confirm all engineering information. This information is not intended to replace the information in the appropriate and applicable standard or code. Ampacity based on 45 C ambient temperature; 95 C values based on ABS MODU Rules Table C values based on IEEE C values based on API 14F. TABLE 3 Three Conductor Cable, Four Conductor Cables with Three Current Carrying Conductors 45 C Ambient Conductor Size Gauge CMA mm 2 95ºC 100ºC 110ºC 125ºC* 14 4, *125 C ampacities based on 45 C ambient in free air. Consult factory for conditions of use. TABLE 4 Cables with more than Four Current Carrying Conductors of Conductors % of 3 Conductor Ampacity Values and greater 30 8

12 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 14 AWG 14 AWG / 600V or 0.6/1kV 1.94 mm 2 GLAND SELECTION GLAND REFERENCE CHART in mm (metric) (NPT) () Hub Size Reference () - NPT Thread Size Reference C14PN-2 T UB AB-52/ NE-04/ 05/ = 1/2" 03 = 1/2" - 14 NPT C14PN-3 T UB AB-52/ NE-04/ 05/ = 1/2" 04 = 1/2" - 14 NPT C14PN-4 T UB AB-52/ NE-04/ 05/ = 3/4" 05 = 1/2" - 14 NPT C14PN-5 T UB AB-53/ NE-05/ 08/ 10/ = 1" 08 = 3/4" - 14 NPT C14PN-6 T UB-02/ AB-53/ NE-05/ 08/ 10/ = 1-1/4" 10 = 3/4" - 14 NPT C14PN-7 T UB-02/ AB-53/ NE-05/ 08/ 10/ = 1-1/2" 14 = 1" /2 NPT C14PN-8 T UB-02/ AB-53/ NE-05/ 08/ 10/ = 2" 15 = 1" /2 NPT C14PN-10 T UB AB NE-10/ = 2-1/2" 20 = 1-1/4" /2 NPT C14PN-12 T UB-03/ AB NE-10/ = 3" 21 = 1-1/4" /2 NPT C14PN-16 T UB-03/ AB-55/ NE-10/ 14/ 15/ = 3-1/2" 27 = 1-1/2" /2 NPT C14PN-20 T UB AB NE-15/ = 2" /2 NPT C14PN-24 T UB-04/ 05/ AB-56/ NE-15/ 20/ 21/ = 2-1/2" - 8 NPT C14PN-30 T UB-04/ 05/ AB-56/ NE-15/ 20/ 21/ = 3" - 8 NPT C14PN-37 T UB-05/ AB NE-21/ = 3" - 8 NPT C14PN-44 T UB-05/ 15/ AB-57/ NE-21/ 27/ 32 C14PN-60 T UB AB NE-32 C14PN-91 T UB AB61 494NE-38 9

13 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / armored and sheathed TYPE P CONTROL CABLE 600V or 0.6/1kV 14 AWG Applications Bostrig P Marine and Offshore Cable is primarily designed for power, control, signal, and instrumentation applications for offshore, land drilling rigs, marine vessels, and offshore production facilities. Bostrig cables have excellent resistance to oil, abrasion, moisture, vibration, sunlight, and ester based mud ( P- MR). They are suitable for use in Class 1, Division 1 offshore applications (armored and sheathed). The standard insulation has a continuous operating temperature of 125 C, allowing for higher ampacity levels. These cables also meet cold bend requirements of -40 C and cold impact of -35 C (CSA 22.2 N0. 0.3). This product may be manufactured in an unarmored or armored and sheathed version. Features/Ratings - Superior resistance to oil, abrasion, moisture, sunlight, crush and impact - High strand count conductors provide superior flexibility - Higher allowable conductor operating temperature results in increased ampacity - Cold bend/ cold impact of -40 / -35 C in accordance with CSA 22.2 No Flame retardant in accordance with IEEE 1202 and IEC Category A - Meets IEEE standards for 600V and performance requirements of IEC standards for 0.6/1 kv - and sheathed cables suitable for use in Class 1 Division 1 and Zone 1 hazardous locations offshore Approvals IEEE 1580 and IEEE 45- Marine Shipboard Cable UL Marine Shipboard Cable X110 CSA 22.2 No Marine Shipboard Cable X110 Det Norske Veritas (DNV) American Bureau of Shipping (ABS) Transport Canada Approved AMS Transport Canada Lloyd s Register of Shipping (LRS) United States Coast Guard-46CFR Construction CONDUCTOR: Soft annealed stranded tinned copper per ASTM B 33. A polyester tape separator is used over the conductor. INSULATION: Bostrig P chemically cross-linked polyolefin (XLPO), meeting IEEE JACKET: Flame-Retardant Thermosetting CPE (Chlorinated Polyethylene) applied over the armor in accordance with the requirements of IEEE as shown in tables on opposite page. Arctic Neoprene ( N) also available as an option. ARMOR: Braided bronze in accordance with IEEE SHEATH: Flame-Retardant Thermosetting CPE (Chlorinated Polyethylene) applied over the armor in accordance with the requirements of IEEE as shown in tables on opposite page. Arctic Neoprene ( N) also available as an option.on opposite page. 10

14 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / armored and sheathed TYPE P CONTROL CABLE 600V or 0.6/1kV 14 AWG 14 AWG / 600V or 0.6/1kV 1.94 mm 2 of Conductor Insulation Sheath Cable Diameter Cable Weight in mm in mm in mm Lbs/Mft Kg/Km C14PNBS-2 T C14PNBS-3 T C14PNBS-4 T C14PNBS-5 T C14PNBS-6 T C14PNBS-7 T C14PNBS-8 T C14PNBS-10 T C14PNBS-12 T C14PNBS-16 T ,065 C14PNBS-20 T ,250 C14PNBS-24 T ,385 C14PNBS-30 T ,175 1,750 C14PNBS-37 T ,345 2,000 C14PNBS-44 T ,510 2,245 C14PNBS-60 T ,020 3,005 C14PNBS-91 T ,215 4,785 The current limit on these cables should be for providing control functions through relays and switching devices. The maximum current for any one conductor should not exceed the value Table 3 for three conductor cables. The average of all conductors should not exceed the limit based on the total number of conductors in the cable taken from Table 4 multiplied by the ampacity from Table 3. Three conductor or four conductor cables with three current carrying conductors may be used for continuous power. This information is provided for reference only. Please consult the factory or your representative to confirm all engineering information. This information is not intended to replace the information in the appropriate and applicable standard or code. Ampacity based on 45 C ambient temperature; 95 C values based on ABS MODU Rules Table C values based on IEEE C values based on API 14F. TABLE 3 Three Conductor Cable, Four Conductor Cables with Three Current Carrying Conductors 45ºC Ambient Conductor Size Gauge CMA mm 2 95ºC 100ºC 110ºC 125ºC* 14 4, *125 C ampacities based on 45 C ambient in free air. Consult factory for conditions of use. TABLE 4 Cables with more than Four Current Carrying Conductors of Conductors % of 3 Conductor Ampacity Values and greater 30 11

15 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / armored and sheathed TYPE P CONTROL CABLE 600V or 0.6/1kV 14 AWG 14 AWG / 600V or 0.6/1kV 1.94 mm 2 GLAND SELECTION GLAND REFERENCE CHART in mm (metric) (NPT) () Hub Size Reference () - NPT Thread Size Reference C14PNBS-2 T AN-01/ 02/ 10 *** 493NE-04/ = 1/2" 03 = 1/2" - 14 NPT C14PNBS-3 T AN-01/ 02/ SW NP-04/ = 3/4" 04 = 1/2" - 14 NPT C14PNBS-4 T AN-02/ 10 *** 493NE-04/ = 1" 07 = 3/4" - 14 NPT C14PNBS-5 T AN SW NP-05/ = 1-1/4" 05 = 1/2" - 14 NPT C14PNBS-6 T AN-03/ SW NP-05/ = 1-1/2" 08 = 3/4" - 14 NPT C14PNBS-7 T AN-03/ SW NP-05/ = 2" 10 = 3/4" - 14 NPT C14PNBS-8 T AN-03/ SW NP-05/ = 2-1/2" 14 = 1" /2 NPT C14PNBS-10 T AN-03/ SW NP-10/ = 3" 15 = 1" /2 NPT C14PNBS-12 T AN-03/ SW NP-10/ = 3-1/2" 20 = 1-1/4" /2 NPT C14PNBS-16 T AN-04/ SW NP-10/ = 1/2" 21 = 1-1/4" /2 NPT C14PNBS-20 T AN-04/ SW NP-15/ = 3/4" 27 = 1-1/2" /2 NPT C14PNBS-24 T AN-04/ 05/ SW NP-15/ = 1" 28 = 1-1/2" /2 NPT C14PNBS-30 T AN SW NP-15/ = 2" /2 NPT C14PNBS-37 T AN SW NP-21/ = 2" /2 NPT C14PNBS-44 T AN SW NP-21/ = 2" /2 NPT C14PNBS-60 T AN SW NP-28/ = 2-1/2" - 8 NPT C14PNBS-91 T AN SW NP = 2 1/2" - 8 NPT 45 = 3" - 8 NPT 47 = 3" - 8 NPT 12

16 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 16 AWG Applications Bostrig P Marine and Offshore Cable is primarily designed for power, control, signal, and instrumentation applications for offshore and land drilling rigs, marine vessels, and offshore production facilities. Bostrig cables have excellent resistance to oil, abrasion, moisture, vibration, sunlight, and ester based mud ( P- MR). They are suitable for use in Class 1, Division 1 offshore applications (armored & sheathed). The standard insulation has a continuous operating temperature of 125 C, allowing for higher ampacity levels. These cables also meet cold bend requirements of -40 C and cold impact of -35 C (CSA 22.2 N0. 0.3). This product may be manufactured in an unarmored or armored and sheathed version. Features/Ratings - Superior resistance to oil, abrasion, moisture, sunlight, crush and impact - High strand count conductors provide superior flexibility - Higher allowable conductor operating temperature results in increased ampacity - Cold bend/ cold impact of -40 / -35 C in accordance with CSA 22.2 No Flame retardant in accordance with IEEE 1202 and IEC Category A - Meets IEEE standards for 600V and performance requirements of IEC standards for 0.6/1 kv - cables suitable for use in Class I Division 2 and Zone 2 hazardous locations - Meets the requirements of UL 1277 and UL 1569 for TC-ER exposed runs Approvals IEEE 1580 and IEEE 45- Marine Shipboard Cable UL Marine Shipboard Cable X110 CSA 22.2 No Marine Shipboard Cable X110 CSA 22.2 No CIC CSA 22.2 No TC-ER Det Norske Veritas (DNV) American Bureau of Shipping (ABS) Transport Canada Approved AMS Transport Canada Lloyd s Register of Shipping (LRS) United States Coast Guard-46CFR Construction CONDUCTOR: Soft annealed stranded tinned copper per ASTM B 33. A polyester tape separator is used over the conductor. INSULATION: Bostrig P chemically cross-linked polyolefin (XLPO), meeting IEEE JACKET: Flame-Retardant Thermosetting CPE (Chlorinated Polyethylene) applied over the armor in accordance with the requirements of IEEE as shown in tables on opposite page. Arctic Neoprene ( N) also available as an option. 13

17 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 16 AWG 16 AWG / 600V or 0.6/1kV 1.23 mm 2 of Conductor Insulation Sheath Cable Diameter Cable Weight in mm in mm in mm Lbs/Mft Kg/Km C16PN-2 T C16PN-3 T C16PN-4 T C16PN-5 T C16PN-6 T C16PN-7 T C16PN-8 T C16PN-10 T C16PN-12 T C16PN-16 T C16PN-20 T C16PN-24 T C16PN-30 T C16PN-37 T ,035 C16PN-44 T ,230 C16PN-60 T ,070 1,590 C16PN-91 T ,645 2,450 The current limit on these cables should be for providing control functions through relays and switching devices. The maximum current for any one conductor should not exceed the value Table 3 for three conductor cables. The average of all conductors should not exceed the limit based on the total number of conductors in the cable taken from Table 4 multiplied by the ampacity from Table 3. Three conductor or four conductor cables with three current carrying conductors may be used for continuous power. This information is provided for reference only. Please consult the factory or your representative to confirm all engineering information. This information is not intended to replace the information in the appropriate and applicable standard or code. Ampacity based on 45 C ambient temperature; 95 C values based on ABS MODU Rules Table C values based on IEEE C values based on API 14F. TABLE 3 Three Conductor Cable, Four Conductor Cables with Three Current Carrying Conductors 45ºC Ambient Conductor Size Gauge CMA mm 2 95ºC 100ºC 110ºC 125ºC* 16 2, *125 C ampacities based on 45 C ambient in free air. Consult factory for conditions of use. TABLE 4 Cables with more than Four Current Carrying Conductors of Conductors % of 3 Conductor Ampacity Values and greater 30 14

18 16 AWG / 600V or 0.6/1kV 1.23 mm 2 GLAND SELECTION GLAND REFERENCE CHART BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 16 AWG in mm (metric) (NPT) () Hub Size Reference () - NPT Thread Size Reference C16PN-2 T UB AB-52/ NE-04/ 05/ = 1/2" 03 = 1/2" - 14 NPT C16PN-3 T UB AB-52/ NE-04/ 05/ = 1/2" 04 = 1/2" - 14 NPT C16PN-4 T UB AB-52/ NE-04/ 05/ = 3/4" 05 = 1/2" - 14 NPT C16PN-5 T UB AB-52/ NE-04/ 05/ = 1" 08 = 3/4" - 14 NPT C16PN-6 T UB AB-53/ NE-05/ 08/ 10/ = 1-1/4" 10 = 3/4" - 14 NPT C16PN-7 T UB AB-53/ NE-05/ 08/ 10/ = 1-1/2" 14 = 1" /2 NPT C16PN-8 T UB-02/ AB-53/ NE-05/ 08/ 10/ = 2" 15 = 1" /2 NPT C16PN-10 T UB-02/ AB-53/ NE-05/ 08/ 10/ = 2-1/2" 20 = 1-1/4" /2 NPT C16PN-12 T UB AB-53/ NE-05/ 08/ 10/ = 3" 21 = 1-1/4" /2 NPT C16PN-16 T UB-03/ AB NE-10/ = 3-1/2" 27 = 1-1/2" /2 NPT C16PN-20 T UB-03/ AB-55/ NE-10/ 14/ 15/ = 2" /2 NPT C16PN-24 T UB AB-55/ NE-10/ 14/ 15/ = 2-1/2" - 8 NPT C16PN-30 T UB AB NE-15/ = 3" - 8 NPT C16PN-37 T UB-04/ 05/ AB-56/ NE-15/ 20/ 21/ = 3" - 8 NPT C16PN-44 T UB-05/ AB NE-21/ 27 C16PN-60 T UB-05/ 15/ AB-57/ NE-21/ 27/ 32 C16PN-91 T UB AB NE-32 15

19 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / armored and sheathed TYPE P CONTROL CABLE 600V or 0.6/1kV 16 AWG Applications Bostrig P Marine and Offshore Cable is primarily designed for power, control, signal, and instrumentation applications for offshore, land drilling rigs, marine vessels, and offshore production facilities. Bostrig cables have excellent resistance to oil, abrasion, moisture, vibration, sunlight, and ester based mud ( P- MR). They are suitable for use in Class 1, Division 1 offshore applications (armored & sheathed). The standard insulation has a continuous operating temperature of 125 C, allowing for higher ampacity levels. These cables also meet cold bend requirements of -40 C and cold impact of -35 C (CSA 22.2 N0. 0.3). This product may be manufactured in an unarmored or armored and sheathed version. Features/Ratings - Superior resistance to oil, abrasion, moisture, sunlight, crush and impact - High strand count conductors provide superior flexibility - Higher allowable conductor operating temperature results in increased ampacity - Cold bend/ cold impact of -40 / -35 C in accordance with CSA 22.2 No Flame retardant in accordance with IEEE 1202 and IEC Category A - Meets IEEE standards for 600V and performance requirements of IEC standards for 0.6/1 kv - and sheathed cables suitable for use in Class 1 Division 1 and Zone 1 hazardous locations offshore Approvals IEEE 1580 and IEEE 45- Marine Shipboard Cable UL Marine Shipboard Cable X110 CSA 22.2 No Marine Shipboard Cable X110 Det Norske Veritas (DNV) American Bureau of Shipping (ABS) Transport Canada Approved AMS Transport Canada Lloyd s Register of Shipping (LRS) United States Coast Guard-46CFR Construction CONDUCTOR: Soft annealed stranded tinned copper per ASTM B 33. A polyester tape separator is used over the conductor. INSULATION: Bostrig P chemically cross-linked polyolefin (XLPO), meeting IEEE JACKET: Flame-Retardant Thermosetting CPE (Chlorinated Polyethylene) applied over the armor in accordance with the requirements of IEEE as shown in tables on opposite page. Arctic Neoprene ( N) also available as an option. ARMOR: Braided bronze in accordance with IEEE SHEATH: Flame-Retardant Thermosetting CPE (Chlorinated Polyethylene) applied over the armor in accordance with the requirements of IEEE as shown in tables on opposite page. Arctic Neoprene ( N) also available as an option. 16

20 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / armored and sheathed TYPE P CONTROL CABLE 600V or 0.6/1kV 16 AWG 16 AWG / 600V or 0.6/1kV 1.23 mm 2 of Conductor Insulation Sheath Cable Diameter Cable Weight in mm in mm in mm Lbs/Mft Kg/Km C16PNBS-2 T C16PNBS-3 T C16PNBS-4 T C16PNBS-5 T C16PNBS-6 T C16PNBS-7 T C16PNBS-8 T C16PNBS-10 T C16PNBS-12 T C16PNBS-16 T C16PNBS-20 T ,010 C16PNBS-24 T ,130 C16PNBS-30 T ,285 C16PNBS-37 T ,080 1,605 C16PNBS-44 T ,125 1,675 C16PNBS-60 T ,580 2,350 C16PNBS-91 T ,365 3,520 The current limit on these cables should be for providing control functions through relays and switching devices. The maximum current for any one conductor should not exceed the value Table 3 for three conductor cables. The average of all conductors should not exceed the limit based on the total number of conductors in the cable taken from Table 4 multiplied by the ampacity from Table 3. Three conductor or four conductor cables with three current carrying conductors may be used for continuous power. This information is provided for reference only. Please consult the factory or your representative to confirm all engineering information. This information is not intended to replace the information in the appropriate and applicable standard or code. Ampacity based on 45 C ambient temperature; 95 C values based on ABS MODU Rules Table C values based on IEEE C values based on API 14F. TABLE 3 Three Conductor Cable, Four Conductor Cables with Three Current Carrying Conductors 45ºC Ambient Conductor Size Gauge CMA mm 2 95ºC 100ºC 110ºC 125ºC* 16 2, *125 C ampacities based on 45 C ambient in free air. Consult factory for conditions of use. TABLE 4 Cables with more than Four Current Carrying Conductors of Conductors % of 3 Conductor Ampacity Values and greater 30 17

21 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / armored and sheathed TYPE P CONTROL CABLE 600V or 0.6/1kV 16 AWG 16 AWG / 600V or 0.6/1kV 1.23 mm 2 GLAND SELECTION GLAND REFERENCE CHART in mm (metric) (NPT) () Hub Size Reference () - NPT Thread Size Reference C16PNBS-2 T AN-01/ 02/ SW NP-04/ = 1/2" 03 = 1/2" - 14 NPT C16PNBS-3 T AN-01/ 02/ SW NP-04/ = 3/4" 04 = 1/2" - 14 NPT C16PNBS-4 T AN-01/ 02/ SW NP-04/ = 1" 07 = 3/4" - 14 NPT C16PNBS-5 T AN-02/ 10 *** 493NE-08/ = 1-1/4" 05 = 1/2" - 14 NPT C16PNBS-6 T AN-02/ SW NP-05/ = 1-1/2" 08 = 3/4" - 14 NPT C16PNBS-7 T AN SW NP-05/ = 2" 10 = 3/4" - 14 NPT C16PNBS-8 T AN-03/ SW NP-05/ = 2-1/2" 14 = 1" /2 NPT C16PNBS-10 T AN-03/ SW NP-10/ = 3" 15 = 1" /2 NPT C16PNBS-12 T AN-03/ SW NP-10/ = 3-1/2" 20 = 1-1/4" /2 NPT C16PNBS-16 T AN-03/ SW NP-10/ = 1/2" 21 = 1-1/4" /2 NPT C16PNBS-20 T AN-04/ SW NP-10/ = 3/4" 27 = 1-1/2" /2 NPT C16PNBS-24 T AN-04/ SW NP-15/ = 1" 28 = 1-1/2" /2 NPT C16PNBS-30 T AN-04/ SW NP-15/ = 2" /2 NPT C16PNBS-37 T AN SW NP-15/ = 2" /2 NPT C16PNBS-44 T AN SW NP 21/ = 2" /2 NPT C16PNBS-60 T AN-05/ SW NP 21/ = 2-1/2" - 8 NPT C16PNBS-91 T AN-06 *** 493NE = 2-1/2" - 8 NPT 45 = 3" - 8 NPT 47 = 3" - 8 NPT 18

22 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 18 AWG Applications Bostrig P Marine and Offshore Cable is primarily designed for power, control, signal, and instrumentation applications for offshore and land drilling rigs, marine vessels, and offshore production facilities. Bostrig cables have excellent resistance to oil, abrasion, moisture, vibration, sunlight, and ester based mud ( P- MR). They are suitable for use in Class 1, Division 1 offshore applications (armored & sheathed). The standard insulation has a continuous operating temperature of 125 C, allowing for higher ampacity levels. These cables also meet cold bend requirements of -40 C and cold impact of -35 C (CSA 22.2 N0. 0.3). This product may be manufactured in an unarmored or armored and sheathed version. Features/Ratings - Superior resistance to oil, abrasion, moisture, sunlight, crush and impact - High strand count conductors provide superior flexibility - Higher allowable conductor operating temperature results in increased ampacity - Cold bend/ cold impact of -40 / -35 C in accordance with CSA 22.2 No Flame retardant in accordance with IEEE 1202 and IEC Category A - cables suitable for use in Class I Division 2 and Zone 2 hazardous locations - Meets IEEE standards for 600V and performance requirements of IEC standards for 0.6/1 kv - Meets the requirements of UL 1277 and UL 1569 for TC-ER exposed runs Approvals IEEE 1580 and IEEE 45- Marine Shipboard Cable UL Marine Shipboard Cable X110 CSA 22.2 No Marine Shipboard Cable X110 CSA 22.2 No CIC CSA 22.2 No TC-ER Det Norske Veritas (DNV) American Bureau of Shipping (ABS) Transport Canada Approved AMS Transport Canada Lloyd s Register of Shipping (LRS) United States Coast Guard-46CFR Construction CONDUCTOR: Soft annealed stranded tinned copper per ASTM B 33. A polyester tape separator is used over the conductor. INSULATION: Bostrig P chemically cross-linked polyolefin (XLPO), meeting IEEE JACKET: Flame-Retardant Thermosetting CPE (Chlorinated Polyethylene) applied over the armor in accordance with the requirements of IEEE as shown in tables on opposite page. Arctic Neoprene ( N) also available as an option. 19

23 BOSTRIG TYPE P CONTROL CABLE 600V OR 0.6/1kV Multi-conductor / unarmored TYPE P CONTROL CABLE 600V or 0.6/1kV 18 AWG 18 AWG / 600V or 0.6/1kV 0.96 mm 2 of Conductor Insulation Sheath Cable Diameter Cable Weight in mm in mm in mm Lbs/Mft Kg/Km C18PN-2 T C18PN-3 T C18PN-4 T C18PN-5 T C18PN-6 T C18PN-7 T C18PN-8 T C18PN-10 T C18PN-12 T C18PN-16 T C18PN-20 T C18PN-24 T C18PN-30 T C18PN-37 T C18PN-44 T C18PN-60 T ,245 C18PN-91 T ,220 1,815 The current limit on these cables should be for providing control functions through relays and switching devices. The maximum current for any one conductor should not exceed the value Table 3 for three conductor cables. The average of all conductors should not exceed the limit based on the total number of conductors in the cable taken from Table 4 multiplied by the ampacity from Table 3. Three conductor or four conductor cables with three current carrying conductors may be used for continuous power. This information is provided for reference only. Please consult the factory or your representative to confirm all engineering information. This information is not intended to replace the information in the appropriate and applicable standard or code. Ampacity based on 45 C ambient temperature; 95 C values based on ABS MODU Rules Table C values based on IEEE C values based on API 14F. TABLE 3 Three Conductor Cable, Four Conductor Cables with Three Current Carrying Conductors 45ºC Ambient Conductor Size Gauge CMA mm 2 95ºC 100ºC 110ºC 125ºC* 18 1, *125 C ampacities based on 45 C ambient in free air. Consult factory for conditions of use. TABLE 4 Cables with more than Four Current Carrying Conductors of Conductors % of 3 Conductor Ampacity Values and greater 30 20