Monogram 36" Built-In Side-by-Side Refrigerator

Transcription

1 STION 1 FLUSH INST INSTLLTION STION 2 STNR INSTLLTION 1/4" FRM PNLS 3/4" OVRLY PNLS

2 OVRLL IMNSIONS FTR PNL INSTLL FLUSH INST INSTLLTION 38" (96.5) 26" (66.0) 20 5/8" (52.4) 11 11/16" (29.7) 15 3/8" (39.1) 84 1/2" (214.6) 72 5/8" (184.5) * 83 1/2" (212.1) 68 5/8" (174.3) *39 17/32" (100.4) SPIFITIONS Overall Width 38" (96.5 cm) Overall Height 84 1/2" (214.6 cm) Overall epth 26" (66.0 cm) oor learance utout Width utout Height utout epth Plumbing Requirements Shipping Weight imensions include 3/4" custom cabinet panel 20 5/8" (52.4cm) 39" (99.1 cm) 85" (215.9cm) 26 3/16" (66.5 cm) 1/4" O copper tubing or G Smartonnect kit 675 lb (306.2 kg) FRONT VIW Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84". **13" (33.0) 35" (89.0) ase width **15" (38.1) 4" (10.2) SI VIW TTNTION LTRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. ** llow 4" (10.2) min clearance to a wall for 90 door swing *115 oor swing oors can be adjusted to 90 door swing TOP VIW ** llow 4" (10.2) min clearance to a wall for 90 door swing 20 5/8" (52.4) ** These refrigerators are equipped with a 2-position door stop. The factory-set 115 door swing can be adjusted to 90 if clearances to adjacent cabinets or walls is restricted. llow a 15" minimum clearance to wall for pan removal. If the 90 door stop position is used, pan access is maintained, but pan removal is restricted. imensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.

3 FLUSH INST INSTLLTION 3/4" PNLS TOP VIW FLUSH INST INSTLLTION ase 5 1/4" (13.3) Finished cleats ase Trim 85" (215.9) 26 3/16" (66.5) Flush inset depth 20 15/16" (53.2) epth to cleat Finished cleats 3/4" (1.9) Width of side cleats 85" (215.9) 3/4" 39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats 6" (15.2) oor 5" (12.7) 12" (30.5) 1/2" (1.3) 75" (190.5 ) From floor to bottom of electrical area Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area. WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. etermine your installation construction and required anti-tip configuration: W SI VIW 3 1/2" (8.9) 7" (17.8) WTR FRONT VIW 7" (17.8) 3 1/2" (8.9) ut a 1" x 4" block 35" long. Measure and mark under the soffit, 5 1/4" from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84". nti-tip racket SOFFIT 2" x 4" ut to 35" Length Wooden Wall Studs and No Soffit ut a 2" x 4" block and secure to brackets provided. Secure brackets to back wall of opening at 84" or your installation height from the floor. See Installation Instructions for detailed instructions. Screws mounted into vertical wall studs *84" (213.4) *Or installation height from floor SI VIW INSTLL UNR SOFFIT SI VIW INSTLL WITH WOON WLL STUS N NO SOFFIT ZIS480X

4 FLUSH INST INSTLLTION 1/2" PNLS 5 3/8" (13.7) TOP VIW ase Finished cleats ase Trim FLUSH INST INSTLLTION 85" (215.9) 26 3/16" (66.5) Flush inset depth 20 13/16" (52.9) epth to cleat Finished cleats 3/4" (1.9) Width of side cleats 85" (215.9) 1/2" 39" (99.1) Flush inset width 37 1/2" (95.3) Width between cleats 6" (15.2) oor 5" (12.7) 12" (30.5) 1/2" (1.3) 75" (190.5 ) From floor to bottom of electrical area Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area. WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. etermine your installation construction and required anti-tip configuration: W SI VIW nti-tip racket SOFFIT 3 1/2" (8.9) 7" (17.8) WTR FRONT VIW 7" (17.8) 3 1/2" (8.9) 2" x 4" ut to 35" Length ut a 1" x 4" block 35" long. Measure and mark under the soffit, 5 3/8" from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84". Wooden Wall Studs and No Soffit ut a 2" x 4" block and secure to brackets provided. Secure brackets to back wall of opening at 84" or your installation height from the floor. See Installation Instructions for detailed instructions. Screws mounted into vertical wall studs *84" (213.4) *Or installation height from floor SI VIW INSTLL UNR SOFFIT SI VIW INSTLL WITH WOON WLL STUS N NO SOFFIT ZIS480X

5 FLUSH INST 3/4" PNL IMNSIONS ispenser utout G Freezer Grille F Fresh Food 3/4" raised door PNL Routing 11/32" 1/4" TIL TOP 3/4" PNL IMNSIONS 38" 11 3/16" 68 5/8" 16 7/8" 20 7/8" ispenser utout 9 5/8" (24.4) 15 3/8" (39.1) ISPNSR UTOUT POSITION F G 17 23/32" 3 3/8" NOT: Routed areas should be finished as they may be visible when assembled. TOP FLUSH INST INSTLLTION Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised door and grille panels, routing is required. The router depth is 1/4" all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door and grille trims. Maximum total panel weight: Fresh food door panels 75 lbs. Freezer drawer panel 53 lbs. Grille panel 18 lbs oor Handles oor handle not included. custom handle supplied by your cabinet maker may be used. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 30 1/2" long. ZKHSS2: uropean tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 64 1/4" long. 1/4" 11/32" Front ack 3/32" ack Front TIL OTTOM ORNR VIW SHOWING PITUR FRM ROUTING TIL HING SI ROUTR PTH 1/4" TIL HNL SI 2 1/16" 3/16" HING SI ack HNL SI 3/4" PNL OTTOM VIW (FTR ROUTING) OTTOM 3/4" PNL SI VIW (FTR ROUTING)

6 3/4" raised grille PNL Routing FLUSH INST INSTLLTION NOT: Routed areas should be finished as they may be visible when assembled. ack Front 2" TIL TOP ROUTR PTH 1/4" ack TOP Front Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised door and grille panels, routing is required. The router depth is 1/4" all the way around the panel s backs. dditional panel width reductions are required per the diagrams shown. This will create picture frame routing allowing the panels to slide into the attached door and grille trims. ORNR VIW SHOWING PITUR FRM ROUTING Maximum total panel weight: Fresh food door panels 75 lbs. Freezer drawer panel 53 lbs. Grille panel 18 lbs. oor Handles oor handle not included. custom handle supplied by your cabinet maker may be used. 3/16" TIL OTTOM OTTOM 3/4" PNL SI VIW (FTR ROUTING) ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 30 1/2" long. ZKHSS2: uropean tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle 64 1/4" long. TIL LFT SI TIL RIGHT SI ROUTR PTH 1/4" ROUTR PTH 1/4" 2 1/16" 2 1/16" Front LFT SI RIGHT SI ack 3/4" PNL OTTOM VIW (FTR ROUTING)

7 ISPNSR TRIM FLUSH INST INSTLLTION 3/4" Flush Freezer oor Ice/Water ispenser 3/4" OVRLY PNL ISPNSR TRIM RIS PNL SIGN ON ISPNSR MOLS 1/2" Overlay 1/4" acker.10" Spacer Freezer oor Ice/Water ispenser 1/2" OVRLY PNL ISPNSR TRIM 3/4" or 1/2" Flush.85" Total Thickness These refrigerators are supplied with a dispenser trim for flush inset panels. ispenser Trim: The provided dispenser trim is designed to fit a total panel thickness of 3/4" or 0.85". If the panel is less than 3/4" thick, a noticeable gap may be created around the dispenser trim. If the panel is more than 0.85" thick, the dispenser trim cannot be secured to the door. The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness. When a raised panel design is to be used, a custom middle rail is required. 16 3/4" 10 5/8" ISPNSR TRIM 3/4" or.85" Total Thickness Raised esign on ispenser Models: When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim. The middle rail must be wide enough to allow for the dispenser trim to overlap the opening. The middle rail must be 3/4" total thickness for 3/4" panels or 0.85" total thickness for 1/2" panels to accept the dispenser trim. SI VIW ROSS STION (Showing Raised with Middle Rail)

8 FLUSH INST 1/2" PNL IMNSIONS ispenser utout G Freezer Grille F Fresh Food PNL IMNSIONS 1/4" acker 33 7/8" 9" 68 3/8" 14 9/16" 18 9/16".10" Space 33" 8 3/8" 67" 13 9/16" 17 9/16" 1/2" Overlay 38" 11 3/16" 68 5/8" 16 7/8" 20 7/8" ispenser utout 9 5/8" (24.4) 15 3/8" (39.1) ISPNSR UTOUT POSITION F G 17 23/32" 3 3/8" FLUSH INST INSTLLTION The 1/2" overlay panel must be secured to a.10" spacer panel and a 1/4" thick backer panel, which slides into the trim. ssemble the panels with glue and screws: enter the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue. Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel. Maximum total panel weight: Fresh food door panel 75 lbs. Freezer drawer panel 53 lbs. Grille panel 18 lbs. 1/4" backer assembly routing dimensions Hinge Side oor 1/2" Overlay acker with Overlay ssembly Freezer ack Fresh Food ack 1/4" acker.10" Spacer PNL IMNSIONS Grille ack Fresh Food 2 1/16" 1/16" 1/8" 1/8" Freezer 2 1/16" 1/16" 1/8" 1/8" Grille 2 1/16" 2 1/16" 2" 7/32"

9 OVRLL IMNSIONS STNR INSTLLTION 25 1/2" (64.8) 36" (91.5) 23 7/8" (60.7) 1 3/4" (4.4) 13 1/2" (34.3) *84" (213.4) *83 1/2" (212.1) 68 1/2" (174.0) *72 1/4" (183.5) *40" (101.6) SPIFITIONS Overall Width Overall Height Overall epth oor learance utout Width 36" (91.44 cm) 84" ( cm) 25 3/8" ( cm) 20 5/8" (52.4 cm) 35 1/2" (90.2 cm) utout Height 83 1/2" /2" ( cm) utout epth Plumbing Requirements Shipping Weight 24" (61 cm) 1/4" O copper tubing or G Smartonnect kit 675 lb (306.2 kg) *3 3/4" (9.5) FRONT VIW * Shipping height. Use leveling legs and wheels for maximum 1" height adjustment from shipping height. ** llow 13" (33.0) min clearance for 130 door swing 35" (89.0) ase width *3 1/2" (8.9) ** llow 15" (38.1) min clearance for 130 door swing SI VIW TTNTION LTRIIN: 115 volt 60Hz., 15 or 20 amp power supply is required. n individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. TOP VIW 20 5/8" (52.4) ** llow 4" (10.2) min clearance to a wall for 90 door swing ** llow 4" (10.2) min clearance to a wall for 90 door swing ** These refrigerators are equipped with a 2-position door stop. The factory-set 130 door swing can be adjusted to 90 if clearances to adjacent cabinets or walls is restricted. llow full 130 door swings for pan removal. If the 90 door stop position is used, pan access is maintained, but pan removal is restricted. imensions in parentheses are in centimeters unless otherwise noted. ctual product dimensions may vary due to manufacturing tolerances.

10 STNR INSTLLTION TOP VIW STNR INSTLLTION 3 1/8" 24" (61) (7.93) 35 1/2" (90.2) 7/16" (1.1) 1 9/16" Trim overlap (3.97) 6" (15.24) 20" (50.8) Mounting the junction box in this location will also allow for front accessibility through access panel. Water supply area. SI VIW nti-tip racket SOFFIT W SI VIW INSTLL UNR SOFFIT 3 1/2" (8.9) *84 1/2" (214.6) *Trim will overlap additional 7/16" 5" (12.7) *84" (213.4) *Or installation height from floor SI VIW INSTLL WITH WOON WLL STUS N NO SOFFIT ZIS480X 5" (12.7) WTR FRONT VIW 2" x 4" ut to 35" Length Screws mounted into vertical wall studs 5" (12.7) 75" (190.5 ) From floor to bottom of electrical area 3 1/2" (8.9) Top ase Trim Install Screws Through Trim and Into 3/4" Min. Wood race The refrigerator will project forward, slightly beyond adjacent cabinetry. FRONT VIW INSTLL WITH MTL WLL STUS N NO SOFFIT 3/4" Min. Side View Top ase Trim WRNING: The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury. The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions. etermine your installation construction and required anti-tip configuration: Installed Under Soffit fter installing unit into installation opening, raise grille panel and screw metal case sides to adjacent cabinet. When installed under a soffit, the soffit cannot exceed 24" deep. The top case trim overlaps the bottom of the soffit. Wooden Wall Studs and No Soffit ut a 2" x 4" block and secure to brackets provided. Secure brackets to back wall of opening at 84" or your installation height from the floor. Metal Wall Studs and No Soffit This method requires securely fastened cabinets on both sides and a 3/4" minimum wood brace above unit, with it s front surface 24" from back wall. fter installing unit into opening, raise grille panel and attach metal case top trim to 3/4" minimum wood brace. The brace spanning the enclosure must be securely fastened to cabinets on both sides. See Installation Instructions for detailed instructions.

11 USTOM SI PNLS F 1 7/8" (4.8) 24" (61.0) 3/16" (.5) *84 *84" (213.4) *epending on installation height STNR INSTLLTION F Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. *3" - 4" ( ) *epending on installation height 2 9/16" (6.5)

12 1/4" FRM PNL IMNSIONS STNR INSTLLTION PNL SSMLY ROSS STION ispenser utout G Grille F Trim oor 1/4" Framed Supplied Handles PNL IMNSIONS 1/4" Framed 33 7/8" 9" 68 3/8" 14 9/16" 18 9/16" Trimmed refrigerators are designed to be customized with decorative panels. Fieldinstalled custom door and grille panels are required. 1/4" Framed s: For 1/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim. Maximum total panel weight: Fresh food door panel 75 lbs. Freezer drawer panel 53 lbs. Grille panel 18 lbs Freezer Fresh Food ispenser utout 15 3/8" (39.1) ISPNSR UTOUT POSITION F G 17 13/16" 3 1/8" 9 5/8" (24.4) 3/4" OVRLY PNL IMNSIONS ispenser utout G Freezer Grille F Fresh Food PNL SSMLY ROSS STION Trim 1/4" acker.10" Spacer PNL IMNSIONS oor 3/4" Overlay Supplied Handles 1/4" acker 33 7/8" 9" 68 3/8" 14 9/16" 18 9/16".10" Spacer 33" 8 3/8" 67" 13 1/4" 17 1/4" 3/4" Overlay 34 1/8" 9 1/4" 68 5/8" 14 13/16" 18 13/16".25" +.10" +.75" = 1.10" Total Thickness ispenser utout 15 3/8" (39.1) *ISPNSR UTOUT POSITION F G 17 15/16" 3 1/4" 3/4" Overlay s: For 3/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. spacer panel 0.10" thick must be placed between the overlay and backer panels. enter each panel over the other. ssemble the panels with glue and screws. Screws must be countersunk into the backer panel. NOT: Left-to-right offset is not always equal to top-to-bottom offset. Maximum total panel weight: Fresh food door panel 75 lbs. Freezer drawer panel 53 lbs. Grille panel 18 lbs oor Handles: The supplied handles can be adjusted to accommodate both framed or overlay panels. ustom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels. ZKHSS2: uropean tubular stainless steel handle designed to fit 3/4" overlay panels. Kits include one handle. Order 2 kits for sideby-side refrigerators from your Monogram supplier. 9 5/8" (24.4) * ut the dispenser opening after the backer, spacer and overlay panels have been assembled.

13 ISPNSR TRIM STNR INSTLLTION 1/4" Framed Freezer oor Ice/Water ispenser 1/4" Total Thickness 1/4" acker Freezer oor.10" Spacer Ice/Water ispenser 1.10" Total Thickness These refrigerators are supplied with two dispenser trims, one for framed panels and one for overlay panels. 3/4" Overlay 1/4" PNL ISPNSR TRIM 3/4" OVRLY PNL ISPNSR TRIM RIS OVRLY PNL SIGN ON ISPNSR MOLS 16 3/4" 1/4" acker.10" Spacer 3/4" Overlay 1/4" ispenser Trim: The framed panel must be 1/4" nominal thickness to fit the dispenser trim. The dispenser trim fits over the custom panel and snaps into the freezer door. If the panel is less than 0.250" thick, a noticeable gap may be created around the dispenser trim. Foam tape may be applied on the door to improve the fit. If the panel is more than 0.250" thick, the dispenser trim cannot be secured to the door. 3/4" Overlay ispenser Trim: The 3/4" overlay dispenser trim is designed to fit a total panel thickness of 1.100" Total Thickness If the panel is less than 1.100" thick, a noticeable gap may be created around the dispenser trim. 10 5/8" ISPNSR TRIM SI VIW ROSS STION (Showing Raised Overlay with Middle Rail) If the panel is more than 1.100" thick, the dispenser trim cannot be secured to the door. The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness. lternative panel construction methods such as securing a 3/4" panel to a 1/4" backer panel cannot be used. nother method, routing a 3/4"-thick panel on all sides, cannot be used. These methods will not result in the required 1.100" panel thickness. When a raised panel design is to be used, a custom middle rail is required. Raised Overlay esign on ispenser Models: When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim. The middle rail must be wide enough to allow for the dispenser trim to overlap the opening. The middle rail must be 1.10" total thickness to accept the dispenser trim.

14 FTURS N NFITS Halogen Light olumns - Located in the freezer and fresh food compartments, extend the full length of the interior compartments providing brilliant, all-level illumination L Lighting - Located at the top of the fresh food compartment, and inside the vegetable and climate-control drawers, illuminates contents without compromising space dvanced Temperature Management System with Multi-Shelf ir Tower - Provides even distribution of air throughout the refrigerator limate-ontrol rawer - llows you to expresschill beverages, express-thaw meats and select specific temperatures for perishable foods ispenser with Proximity Sensor - esigned to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when you walk away airy in with enter ivider - Has a unique magnetic seal that locks in freshness Filter-hange Indicator Light - Located on the upfront control panel, provides a visual reminder when it's time to replace the filter for the water dispenser G Water Filter - Has been moved from the fresh food compartment to the overhead cabinet, where it is discreetly out of sight rop-own Shelf - Provides additional space for a casserole dish or pizza box R