Power Supplies. SHP Series: Heavy Duty Modular Power Supplies

Transcription

1 Power upplies HP eries: Heavy Duty Modular Power upplies his new generation of high power, intelligent modular power supplies, range from 500 through 4920 watts and were designed for optimum flexibility. he modular design makes these units easy to customize for unusual voltage and power combinations, and the intelligent modules allow the use of I 2 C or CANBU/R485 communication to monitor and control many attributes of the power supply. All units have power factor corrected inputs, an end mounted fan for cooling and a variety of built-in signals and controls. High reliability and a flexible design make these power supplies an excellent choice for process control and semiconductor fabrication applications. Applications Process Controls emi-conductor Fabrication Automated ervice Equipment Features Available in intelligent and non-intelligent models ingle, dual and triple output modules configurable in combinations up to 24 different outputs ingle phase and three phase inputs I 2 C control in intelligent modules End mounted intelligent fan (speed control/fault status) Voltage adjustment on all outputs (manual or I 2 C) CANBU and R-485 optional interface verload protection on all outputs Power factor correction (.99 typ.) Configurable output UP/DWN sequencing Modular Construction Configurable input and output K signals and indicators Programmable voltage, current limit, inhibit/enable through I 2 C hree year limited warranty Certifications and Compliances U Recognized Component, IE, E762 - U /CA C22.2 No , 2nd Edition E762 Related Products urge Protective Devices CD DC to DC Converters Active racking Filters tandard ffering election able Catalog Number utput Voltage utput Current Watts H0-4-0Z 2 V 25 A 500 H0-4N-0Z 5 V 00 A 500 H0-4Q-0Z 24 V 62 A 500 H0-4R-0Z 28 V 5 A 500 H0-4W-0Z 48 V A 500 H45-4Q-Q-4Z 24 V 92 A 2000 Accessories able Catalog Number Description UB to I 2 C adapter Mating Connector Kit for Control & ignals (J Connector) Mating Connector Kit for I 2 C Interface (J2 Connector) Note: Connector kit includes connector housing and 0 terminals. - ow Voltage Directive - IEC/EN , 2nd Edition 68 Contact echnical ervices at (800) with any questions.

2 Power upplies pecifications Description H0 H45 H H5 Input voltage range Vac; Vdc; ingle-phase Vac; hree-phase Frequency Inrush current Efficiency Power factor urn-on time Hold-up time AC K utput voltage range Input 47 6 Hz 40 A peak maximum (soft start) Up to 85% at full load 0.99 typical AC on.5 s typical, inhibit/enable 50 ms typical, configurable through I 2 C; 50 ms internal turn-on delay (dual output only) 0 ms minimum >5 ms early warning before outputs lose regulation, full cycle ride through at 50 Hz, configurable through I 2 C utput ±0% minimum for all outputs, user-adjustable pot, full adjustment range using I 2 C Factory set point accuracy 0.0 I 2 C output program accuracy ±5% Margining ine/load regulation Ripple Dynamic response Recovery time vercurrent protection hort-circuit protection vervoltage protection hermal protection Remote sense ingle wire parallel DC K Minimum load Housekeeping bias voltage Module inhibit utput/output isolation Global inhibit/enable ±4 6% nominal analog (single output module only) 0.4% or 20 mv maximum (% maximum for 500 W module) RM: 0.% or 0 mv maximum; Pk-Pk:.0% or 50 mv maximum; bandwidth limited to 20 MHz <2% or 00 mv with 25% load step Within % in <00 μs ingle output module and main output of the dual output module 05 20% of rated output current. Aux output of dual output module 05 40% of rated output current. pecial programmable CP delay on 500 W module from 00 ms to 25.5 s with shutdown features. Configurable through I 2 C with load calibration required (except for 500 W module). Protected for continuous short-circuit; recovery is automatic upon removal of short. hutdown mode available on the 500 W module. ingle output module: V, 22 4%; 6 60 V, 0 20%; Dual output module: 2 6 V, 22 4%; 8 28 V, 0 20% riple output module: No overvoltage protection provided; Configurable through I 2 C All outputs are disabled when the internal temperature exceeds the safe operating range; configurable through I 2 C Up to 0.5 V drop (not available on triple output module) Current share to within 2% of total rated current ±5% of nominal; configurable through I 2 C Not required 5 V A maximum present whenever ac input is applied Configured and controlled through I 2 C > MΩ, 500 V, ogic and ogic 0 ; configurable through I 2 C Environmental perating temperature -40 C to +70 C ambient; derate each output 2.5% per degree from 50 C to 70 C torage temperature -40 C to +85 C Humidity Vibration MBF demonstrated 0% to 95% RH, non-condensing IEC to the levels of IEC72--2 >550,000 full load, 220 V ac, 25 C ambient Electromagnetic susceptibility EN , EN , EN evel EMI filter Radiated EMI afety CIPR 22/EN55022 evel B when installed in a properly grounded and shielded metal enclosure CIPR 22/EN55022 evel B when installed in a properly grounded and shielded metal enclosure General Case dimensions H x W x D in (mm) 5 x 5 x (27.0 x 27.0 x 279.4) 5 x 8 x (27.0 x 20.2 x 279.4) 5 x 5 x (27.0 x 27.0 x 279.4) 5 x 8 x (27.0 x 20.2 x 279.4) Case weight 6.2 lbs (2.8 kg) 9.0 lbs (4.08 kg) 6.2 lbs (2.8 kg) 9.0 lbs (4.08 kg) lots available per case imited warranty years Contact echnical ervices at (800) with any questions. 69

3 Power upplies utput Module pecification verview Intelligent Module Code Module ype ingle ingle ingle ingle Dual riple Max output power 20 W 60 W 750 W 500 W 44 W 6 W Max output current 2 5 A 60 A 50 A 40 A 0 A 2 A utput voltages available 2-60 V 2-60 V 2-60 V 6-60 V 8-5, 24-28; 8-5, 8-5; 8-5, 2-6; 2-6, 2-6; 24-28, 24-28; 24-28, , 8-5, 2-6; 8-5, 8-5, 8-5; 8-5, 8-5, 8-28; 8-5, 8-28, 2-6 tandard voltage increments Remote sense Yes Yes Yes Yes Yes Yes No Remote margin Yes Yes Yes Yes No No No Program - I 2 C control Yes Yes Yes Yes Yes Yes No Active current share Yes Yes Yes Yes Yes No No Module inhibit - I 2 C control Yes Yes Yes Yes Yes Yes Yes Module inhibit - Analog Yes Yes Yes Yes No No No vervoltage/vercurrent protection Yes Yes Yes Yes Yes Yes Yes Minimum load required No No No No No No No lots occupied in any HP case 2 4 Weight 0.6 lbs (0.27 kg).0 lbs (0.45 kg).6 lbs (0.7 kg) 2.0 lbs (0.9 kg) 0.6 lbs (0.27 kg) 0.5 lbs (0.2 kg) Non-Intelligent Module Code Module ype ingle ingle ingle - Dual riple Max output power 20 W 60 W 600 W - 44 W 6 W Max output current 5 A 60 A 20 A - 0 A 2 A utput voltages available 2-60 V 2-60 V 2-60 V V 2-28 V tandard voltage increments Remote sense Yes Yes Yes - Yes Yes No Remote margin/program Yes Yes Yes - No No No Module inhibit - isolated Yes Yes Yes ingle wire active current share Yes Yes Yes - Yes No - vervoltage/vercurrent protection Yes Yes Yes - Yes Yes vercurrent Minimum load required No No No - Yes (0% of load) lots occupied in any HP case 2 - Weight 0.6 lbs (0.27 kg).0 lbs (0.45 kg) 2.0 lbs (0.9 kg) lbs (0.27 kg) No No 0.5 lbs (0.2 kg) ) For dual & triple output modules: the max output power is the total amount of power for the module. 2) For dual & triple output modules: the max output current is the total max current for each output. ) o calculate the total weight of the power supply: sum up the weight for each module and add it to the weight of the case given under the pecifications able. 70 Contact echnical ervices at (800) with any questions.

4 Power upplies Catalog Numbering election Intelligent Model Example: 4500W case with: a 500W module set at 62.5A and a 750W module set at 0A connected in parallel for a total of 92.5A single output. H45-4Q-Q-4Z Case ize Module Codes Case ptions ingle Phase Input H0 = 500 W - 20 W, 9 lots H45 = 800 W W, 4 lots hree Phase Input H = 20 W, 9 lots H5 = 4920 W, 4 lots = 20 W single /P ( slot) 2 = 60 W single /P (2 slot) = 750 W single /P ( slot) 4 = 500 W single /P (4 lot) 5 = 44 W dual /P ( slot) 6 = 6 W triple /P ( slot) X = Extra 0m hold-up ( slot) utput Voltage Codes ee utput Module Voltage/Current able for Intelligent Modules Module ption Codes = tandard = Module enable U = Constant current V = & U combined W = hutdown mode for 500 W Y = & W combined Paralleling ptions 0 = No Parallel ption -9 = ee Parallel Code able utput Voltage/Current able for Intelligent Modules 2 pecial ptions Z = No ptions R = Reverse air N = Not used G = Global enable F = Fan Idle w/inhibit H = pt R + pt G I = pt R + pt F J = pt G + pt F K = pt R + G + F C = CANBU/R485 ( ) B = UB ( ) HP eries: Intelligent Modules ingle Voltage Voltage I 2 C ingle utput Dual utput Code riple utput Adjustment Ranges 4 Module Code Module Code V A 5 A 60 A 50 A - 0 A 0 A A V 2.2 V B 5 A 60 A 50 A - 0 A 0 A A V V C 5 A 60 A 50 A - 0 A 0 A A V. V D 5 A 60 A 50 A - 0 A 0 A A V 5 V E 5 A 60 A 50 A - 0 A 0 A A V 5.2 V F 5 A 60 A 44 A - 0 A 0 A A V 20 W 750 W 5.5 V G 4 A 58 A 6 A - 0 A 0 A A V 6.0 V H 2 A 42 A 97.5 A 40 A 0 A 0 A A V 8.0 V I 20 A 6 A 84.4 A 40 A 0 A 4 A A A A V 0 V J 8 A 2 A 75 A 40 A 0 A 4 A A A A V V K 7 A A 68 A 6. A 0 A 4 A A A A V 2 V 7 A 0 A 62.5 A 25 A 0 A 4 A A A A V 4 V M 4 A 2 A 5.5 A 07 A 9 A 4 A A A A V 5 V N 4 A 20 A 50 A 00 A 8 A 4 A A A A V 60 W 500 W 8 V A 9 A 4.6 A 8. A A 0.5 A V 20 V P 0.5 A 8 A 7.5 A 75 A A 0.5 A V Dual riple 24 V Q 8.5 A 5 A 0 A 62.5 A 4 A 2 A A 0.5 A V 28 V R 6.7 A A 26.8 A 5.5 A A 2 A A 0.5 A V 0 V 6.5 A A 25 A 50 A V V 6.2 A 0.9 A 22.7 A 5.8 A V 6 V U 5.8 A 0 A 20.8 A 5.8 A V 42 V V 4.2 A 7.5 A 6 A 5.7 A V 48 V W 4.0 A 7.5 A 5.6 A.2 A V 44 W 6 W 54 V X.7 A 6.0 A.9 A 27.7 A V 60 V Y.5 A 6.0 A 2.5 A 25 A V ) Certifications pending. 2) Increments of current not shown can be achieved by paralleling modules. ee Parallel Code able. ) otal output power on dual and triple modules must not exceed the max output power rating for the module. 4) I 2 C Adjustment Ranges apply to single output modules only. Contact echnical ervices at (800) with any questions. 7

5 Power upplies Catalog Numbering election Non-Intelligent Model Example: 20W case with: a 6W triple output module set at A, 0.5A, 2A and a 600W module set at 2.5A. H0-6KQE-Q-0Z Case ize Module Codes Case ptions ingle Phase Input H0 = 500 W - 20 W, 9 lots H45 = 800 W W, 4 lots hree Phase Input H = 20 W, 9 lots H5 = 4920 W, 4 lots = 20 W single /P ( slot) 2 = 60 W single /P (2 slot) = 600 W single /P ( slot) 5 = 44 W dual /P ( slot) 6 = 6 W triple /P ( slot) X = Extra 0m hold-up ( slot) utput Voltage Codes ee utput Module Voltage/Current ables for tandard Modules Paralleling ptions 0 = No Parallel ption -9 = ee Parallel Code able pecial ptions Z = No ptions R = Reverse air N = Not used G = Global enable F = Fan Idle w/inhibit H = pt R + pt G I = pt R + pt F J = pt G + pt F K = pt R + G + F C = CANBU/R485 ( ) 2 B = UB ( ) 2 72 HP eries: Non-Intelligent Modules ingle Dual 20 W 44 W 60 W riple 6 W utput Voltage/Current able for Non-Intelligent Modules Voltage Voltage Code Contact echnical ervices at (800) with any questions. ingle utput Dual utput 4 riple utput Module Code Module Code V A 5 A 60 A 20 A - 0 A A 2.2 V B 5 A 60 A 20 A - 0 A A V C 5 A 60 A 20 A - 0 A A. V D 5 A 60 A 20 A - 0 A A 5 V E 5 A 60 A 20 A 0 A 0 A A 5.2 V F 5 A 60 A 5 A - 0 A A 5.5 V G 4 A 58 A 09 A - 0 A A 6.0 V H 2 A 42 A 78 A - 0 A A 8.0 V I 20 A 6 A 68 A - - A A A 0 V J 8 A 2 A 60 A - - A A A V K 7 A A 54.5 A - - A A A 2 V 7 A 0 A 50 A 0 A 4 A A A A 4 V M 4 A 2 A 40.5 A 9 A 4 A A A A 5 V N 4 A 20 A 9 A 8 A 4 A A A A 8 V A 9 A. A A 0.5 A 20 V P 0.5 A 8 A 0 A A 0.5 A 24 V Q 8.5 A 5 A 2.5 A 4 A 2 A A 0.5 A 28 V R 6.7 A 2.8 A 2.4 A A 2 A A 0.5 A 0 V 6.5 A 2 A 20 A V 6.2 A 0.9 A 8.2 A V U 5.8 A 0 A 6.6 A V V 4.2 A 7.5 A 2.5 A V W 4.0 A 7.5 A 2.5 A W 54 V X.7 A 6.0 A A V Y.5 A 6.0 A 0 A ) Certifications pending. 2) nly the input parameters will have communications capabilities with these options. Non-intelligent modules do not provide communication capabilities on the output side. ) Increments of current not shown can be achieved by paralleling modules. ee Parallel Code able. 4) otal output power on dual and triple modules must not exceed the max output power rating for the module.

6 Power upplies Parallel Code able Parallel Code H0 & H H45 & H5 lot No. Possible Configurations (Modules in Watts) lot No. Possible Configurations (Modules in Watts) & ; 20-44; & 2 AC ; 20-44; & 60-60; 60-20; 60-44; + above 2 & 60-60; 60-20; 60-44; + above & & ; ; ; 20-20; 20-44; ; ; 20-20; 20-44; 44-44; 60-20; & 4 4 & ; ; ; ; 20-20; 20-44; ; ;500-60; ; ; 20-20; 20-44; 44-44; 60-60; 60-20; , 4, & ; ; , 4, & ; ; & ; , 5, & ; ; , 5, & ; ; & , 5, & ; ; ; ; & ; ; , 5 & 9; 2 & ; ; & 4; 8 & & & 5; & & , 4 & & 7;, 4, & 2 750, 750, 60, 750, 750 2, 4, 6; 8 & 9 750, 60, 750, 20, 4,, & 2 750, 750, 750, & & 4; & & ; & ,4 & & & 5; 9 & & & 9; 5 & & & 4; 7 & 8; 9 & & & , 4 & 9; 6 & 7 750, 750, 60, 750 Contact echnical ervices at (800) with any questions. 7

7 Power upplies Connector ables able : AC Input 2 N ~ H0, H H Pin # H0 & H45 AC neutral (DC -) function ~ H & H5 2 AC line (DC +) 2 Chassis (earth) ground 4 2 Chassis (earth) ~ H5 4 ground Barrier type H0: three #6-2 bh screws, 6 in.-lbs. (0.67 n-m) torque H45: three M4 screws, 7 in.-lbs. (0.79 n-m) torque H: four M screws, 6 in.-lbs. (0.67 n-m) torque H5: three M.5 screws, 6 in.-lbs. (0.67 n-m) torque able 2: PFC Input Connector (Control & ignals) 6 Connector J Mates with: molex housing Molex terminal Connector kit p/n Pin # function Input ac K (emitter) 2 Input ac K (collector) Global dc K (emitter) 4 Global dc K (collector) 5 No connection 6 Global inhibit/optional enable logic 0 7 Global inhibit/optional enable logic 8 Global inhibit/optional enable return 9 +5 VB housekeeping (A max) 0 +5 VB housekeeping return able : I 2 C Bus utput Connector 0 5 Connector J2 6 Mates with: J phdr-0vs housing jst sphd-002t-p0.5 terminal (for AWG wire) jst sphd-00t-p0.5 terminal (for AWG wire) or land win 2050s000 housing land win 205t0P terminal Connector kit p/n Pin # function 2 No connection 4 erial clock signal (C) 5 erial data signal (DA) 6 Address bit 0 (A0) 7 Address bit (A) 8 Address bit 2 (A2) 9 econdary return (GND) 0 5 VCC external bus (A max) able 4: DC utput Connector (ocated on output modules) 6 Connector J 5 0 Mates with: molex housing Molex terminal Connector kit p/n Pin # function + Remote sense (single or dual o/p main) 2 Remote margin/v. program (single o/p) Margin high (single o/p) 4 - Remote sense/margin low (single or dual o/p main) 5 pare 6 Module isolated inhibit (single or dual o/p) 7 Module inhibit return (single or dual o/p) 8 Current share (WP) (single or dual o/p main) 9 + Remote sense V2 (dual o/p, single is spare) 0 - Remote sense V2 (dual o/p, single is spare) utput Module Connections: M4 x 8mm screws for all single output modules; maximum torque is 0 in.-lb. (. N-m). M x 8mm screws for dual output module; maximum torque is 5 in.-lb. (0.57 N-m). 6W triple output module connector mates with Molex housing and Molex terminals. Case pecifications Case Dimensions H0 = 5 x 5 x (27 x 27 x 279.4) 9 available slots, ingle-phase Input Vac Vac 500 W max. 20 W max H = 5 x 5 x (27 x 27 x 279.4) 9 available slots, hree-phase N/A Vac 20 W max H45 = 5 x 8 x (27 x 20.2 x 279.4) 4 available slots, ingle-phase Vac Vac 800 W max W max H5 = 5 x 8 x (27 x 20.2 x 279.4) 4 available slots, hree-phase N/A Vac 4920 W max. 74 Contact echnical ervices at (800) with any questions.

8 Power upplies H0 and H Dimensional Drawings 5.00 ± 0.02 [ ± ] [27.0 ± 0.5] 5.00 ± 0.0 [ ± ± ] [27.0 ± 0.9] UB PRGRAMMING CNNECR UB PRGRAMMING CNNECR PFC INPU CNNECR PFC INPU CNNECR I 2 C BU UPU CNNECR I 2 C BU UPU CNNECR J 5 0 J2 6 J 5 0 J DC K DC K AC K AC K REVERE REVERE AIRFW AIRFW DIRECIN DIRECIN NRMA NRMA AIRFW AIRFW DIRECIN DIRECIN AC AC INPU INPU ± ± [ [ ±.27].27] M4 MG HE (4X). ee Connectors able for screw types. 2. Chassis material: aluminum with chemical film coating (conductive).. All dimensions are in millimeters and inches, and are typical. 4. Customer mounting - sides M4, bottom also includes 8-2 mounting holes. Max. penetration is 0.55 (4.0mm). Max. torque: 5in-lbs. (0.57N-m). Contact echnical ervices at (800) with any questions. 75

9 Power upplies H45 and H5 Dimensional Drawings 8.00 ± 0.02 [20.2 ± 0.5] 5.00 ± 0.0 [27.0 ± 0.9] UB PRGRAMMING CNNECR PFC INPU CNNECR I 2 C BU UPU CNNECR 0 J2 6 5 J DC AC K K REVERE AIRFW DIRECIN NRMA AIRFW DIRECIN.00 ± 0.05 [279.4 ±.27] AC INPU M4 MG HE (4X). ee Connectors able for screw types. 2. Chassis material: aluminum with chemical film coating (conductive).. All dimensions are in millimeters and inches, and are typical. 4. Customer mounting - sides M4, bottom also includes 8-2 mounting holes. Max. penetration is 0.55 (4.0mm). Max. torque: 5in-lbs. (0.57N-m). 76 Contact echnical ervices at (800) with any questions.

10 Power upplies Intelligent Modules Dimensional Drawings ingle 20 Watt.44 (.2) 2x.6. (6.0) (8.5) ingle 60 Watt M4x8 screws with conical washer.8 (5.).48 (2.).44 (.2).44" (.4) M4X8 screws with conical washer Pin DC utput Connector.48 (2x) (2.).8 (2x) (5.2) Pin.2 (8.) DC utput Connector.2 (8.) ingle 750 Watt ingle 500 Watt.59 (5.0).6 (6.0) (x) (x) (5.6) 2x DC utput Connector (2x) (2x) (.0) 2x.44 (.0) Pin For Factory-Use nly (2x) M4x8 screw w/ conical washer (6x).2 (8.) M4x8 Pin screws (4x) DC utput Connector.46 (.7) (4x) Dual 44 Watt riple 6 Watt V2 Adj.0 (7.5) (x).7 (29.7).42 (0.7).2 (8.) V2+ V2- MX8 screws with spring washer (4x) V2 Adj Pin 2. Ref. V2+ V+ V Adj V2+ V2- V2- V- V+ V-. utput Module Connections: All single /P modules are M4 x 8mm screws. Maximum torque:0 in.-lbs. (. N-m). Dual /P module is M x 8mm screws. Maximum torque: 5 in.-lbs. (0.57 N-m). 2. All output modules have a green DC K ED, (except for 6W module).. ee Connectors able 4 for mating connector kits. Contact echnical ervices at (800) with any questions. 77

11 Non-Intelligent Modules Dimensional Drawings Power upplies ingle 20 Watt.44 (.2) (2x) M4x8 screws (2x).48 (2.).8 (5.).44 (.2) Pin ingle 60 Watt.2 (8.) ingle 600 Watt. (8.5).6 (6.0).59 (5.0).6 (6.0) M4x8 screws (4x) M4x8 screws (4x).48 (2.) (2x).44 Pin (.2).8 (5.).6 (5.6) (2x).44 (.2).24 (.6) (2x).2 (8.).2 (8.) Pin Dual 44 Watt riple 6 Watt.46 (.7) (4x) 0 (7.5) (x).7 (29.7).42 (0.7).84 (2.) V2 Adj Pin DC utput Connector V2+ V2- Mx8 screws (4x) V2 Adj V2+ V2- V+ V-.2 (8.) Pin.48 (2.) V Adj. utput Module Connections: All single /P modules are M4 x 8mm screws. Maximum torque:0 in.-lbs. (. N-m). Dual /P module is M x 8mm screws. Maximum torque: 5 in.-lbs. (0.57 N-m). 2. All output modules have a green DC K ED, (except for 6W module).. ee Connectors able 4 for mating connector kits. 78 Contact echnical ervices at (800) with any questions.