Capoeira Color C172. Line of Decorative Effects

Transcription

1 Capoeira Color C172 Line of Decorative Effects

2 wood Capoeira Color C172 welcoming, heat For Primer: - Suvinil Vinyl Putty - Suvinil Latex Maxx or Suvinil Acrylic Matt in white color or brush - Steel trowel and spatula - Sandpaper for putty, grain - Trays or buckets for paint : - Suvinil Texturatto Special in the desired color - 4-inch wide brush or bigger - Tool for wood effect - Masking tape - Cotton fabric for polishing - 280/320 grain sandpaper - Soft sponge - Pasty, colorless wax for floor, marble, wood Making the primer 1. If necessary, apply 2-3 coats of Suvinil Putty by using a steel trowel and spatula. 2. Apply 2-3 coats of Suvinil Latex Maxx or Suvinil Acrylic Matt in white color by using a wool roller or paintbrush, observing the drying interval. Leave to dry at list 24 hours before you begin the painting process of wood effect. Note: On previously painted walls with putty a slight sandpapering is recommended, then remove the dust with a wet cloth and apply Suvinil Latex Maxx or Suvinil Acrylic Matt Divide the surface into areas of approximately 1m width. 4. Apply one coat of Suvinil Texturatto Special, as if it were an ordinary paint, a uniform coat diluted with 15% to 20% water by using a large brush. 5. Then, with the product still humid, slide the brush over the surface again in vertical movements from top to bottom successively forming small grains. Note: This process should be fast in order that the Texturatto does not dry. 6. Let this coat dry for at least 6 hours. When the wall is dry, apply a second coat of the product diluted 15%, and then use the tool of the wood effect for this purpose. Note: Leave spaces between 5 and 10cm between coats of the tool of wood effect. Suvinil Texturatto Special is a very absorbent product, so, make sure the first coat is fully hidden with the second coat. ATTENTION: for the correct use of the tool, see picture below of how to use it and what direction. 7. Leave to dry for at least 6 hours. Make a slight,uniform sandpaper of the entire surface by using a 280/320 grain sandpaper in order to remove the upper little part of the product left during application. 8. Eliminate the dust by using a hair broom or dry cloth. Note: Do not use wet cloth, because the product can be stained. 9. With a soft sponge apply pasty wax in a uniform way without pressure, making circular movements. Leave to dry for 5 minutes. Make the polishing of the surface until getting the desired gloss by using a cotton fabric. Hints: When applying Texturatto Special, make the applied coat as uniform as possible. The surface to be applied should be as flat as possible with vinyl putty or Styrene acrylic putty finish. Instructions of dilution and drying should be checked on the packaging. A mask against dust should be used when sandpapering. Side walls should be set apart with masking tape before you begin working. It is advisible that 2 people apply the effect so as the product does not dry quickly.

3 silk class, softness Erva Doce Color A410 For primer: - Suvinil Silk Touch Acrylic White For effect: - Suvinil Acrylic Metalized - Soft cotton fabric without lint (T-shirt) Making the primer 1. With the wool roller apply 2-3 coats of Suvinil Acrylic Silk Touch white on the surface, observing the drying interval. 2. After 24 hours the surface will be completely dry and ready to receive the silk effect. 3. Divide the wall into areas of approximately 1m width. The product has a faster drying, so it is necessary to work on small areas to obtain the ideal finish. 4. Put Suvinil Acrylic Metalized on a tray, soak the fabric in the product and remove the surplus on the tray side. 5. Create the effect by slightly touching the fabric on the surface, making irregular movements. 6. Change the direction of the coat so that the fabric does not create a regular stain on the surface. Hints: You may use a colorful primer to create other effects. Before you begin painting make sure the surface is correctly prepared, clean, dry and free of loose parts. The products should be correctly diluted according to the instructions on the packaging label before application. Side walls should be set apart with masking tape before you begin working. 5 6

4 suede Color E 168 warmth, comfort For primer: - Suvinil Acrylic Matt or Suvinil Maxx White - Low hair wool roller - Masking tape - Sandpaper for wall For effect: - Suvinil Acrylic with Microspheres in two tones (clear and dark) of the same color or similar color - Soft cotton fabric - Masking tape - Bucket with water Making the primer 1. With the wool roller, apply 1-2 coats of Suvinil Acrylic Matt or Suvinil Maxx White, observing the drying interval. 2. After 8 hours, the surface will be completely dry and ready for receiving Suvinil Acrylic Microspheres. Note: the surface should be as flat as possible (Vinyl putty, Styrene Acrylic Putty, plaster of Paris) : 3. Apply 1 coat of Suvinil Acrylic Microspheres by using a low hair wool roller in THE CLEAREST TONE diluted up to 20% water. 4. Leave to dry for at least 4 hours. 5. Divide the surface into vertical stripes of 70cm width and apply with a low hair wool roller on the first stripe 1 coat of Suvinil Acrylic Microspheres in a DARKER TONE diluted up to 20% water. 6. Then, still in the first stripe, with the product as wet as possible, apply the cotton fabric folded unevenly and slightly wet with water, hitting it successively in order to remove part of the product and show the fabric plots drawings and a little color which is underneath. Note: It is very important that intervals between application with wool roller and the use of fabric is as soon as possible in order that the product does not dry and forms seams (items 5 and 6). 7. After finishing a stripe the fabric should be washed quickly in a bucket with water to remove the surplus of the product and twist it well. It is advisible that 2 people apply the product. The first one applies with the wool roller and the second makes the effect with the fabric. Hints: The choice of colors is very important. Try to work with colors that are as close as possible, varying only clear and dark tones between colors. We remind that the more distant are the tones the bigger the contrast will be. The clearest color as a first coat is very important for the final result be the expected one. Darker color should never be applied as the first coat. Check the dilution and drying time instructions on the packaging label. During the sandpaper process always use the mask against dust. Side walls should be set apart with wide masking tape (50mm) before you begin working.

5 bare concrete Color D 164 modernity, technology For wall preparation: - Suvinil Acrylic Premium Matt in white color To make the effect: - Suvinil Texturatto Special (old Suvinil Texturatto Marmoratto) in the desired color (suggestion D164) - Stainless trowel with rounded corners - Soft sponge - Pasty colorless wax - White, soft, clean and dry cotton fabric (ideal is a cotton fabric T-shirt cotton waste should not be used) - 320/360 sandpaper 1. Apply 2-3 coats of Suvinil Acrylic Premium Matt on the wall with a wool roller always observing the dry interval. 2. After 24 hours the surface will be dry and ready to receive the effect. 3. Divide the wall into 1.10m width areas. 4. With a stainless steel trowel apply 1 coat of Texturatto Special as it were a vinyl putty to make the surface as uniform as possible and fully hidden. 5. Wait for the drying time (24 hours). 6. Sandpaper the surface slightly to remove the biggest reliefs left by the application and remove the dust. Note: Small reliefs are a characteristic of a bare concrete, so we suggest not to remove them completely. 7. Then, apply 1 coat of pasty wax by using a soft sponge. 8. Leave the wax to dry for 5 minutes and with the cotton fabric make the manual polishing or use the polishing machine

6 bamboo refinement, sophistication, brightness Color D 141 For wall preparation: - Suvinil Acrylic Premium Matt white For making the effect: - Suvinil Texturatto Special (old Suvinil Texturatto Marmoratto) in the desired color (suggestion D 142) - Stainless trowel with rounded corners - Common steel trowel - Steel spatula - Pasty colorless wax - White, soft, clean and dry cotton fabric (ideal is a cotton fabric T-shirt cotton waste should not be used) - 320/360 sandpaper - Soft sponge 1. Apply 2-3 coats of Suvinil Acrylic Premium Matt on surface with a wool roller, always observing the drying interval. 2. After 24 hours the surface will be dry and ready to receive the effect. 3. Work in a 1 m width area on the surface. 4. Apply one coat of Suvinil Texturatto Special with a rounded corners trowel, leaving the surface completely hidden. 5. With Suvinil Texturatto Special humid, start from the upper corner, with a common stainless trowel or spatula, making short, horizontal and successive movements to form the bamboo segments. 6. Leave to dry (24 hours). 7. Sandpaper the surface with more intensity on higher reliefs, leaving the drawing depressions with a slight sandpapering and a roundness appearance will come up. Eliminate the dust. 8. Apply 1 coat of pasty, colorless wax with a soft sponge and leave to dry for 5 minutes. 9. With a cotton fabric make the manual polishing

7 washed jeans Color R 085 Wall preparation: - Suvinil Acrylic Premium Silk Touch white : - Suvinil Gel in the desired color - Foam roller - Jeans roller - Cotton fabric measuring approximately 40 cm x 40 cm - Masking tape 1. Apply 2-3 coats of Suvinil Acrylic Premium Silk Touch on the surface with a wool roller always observing the drying interval. 2. After 24 hours the surface will be dry and ready for applying the effect. spontaneity, relaxation, versatility 3. Divide the wall into 1.10m wide stripes by using a masking tape. 4. With a foam roller, apply one coat of Suvinil Gel making the surface as more homogeneous as possible. 5. Moisten the cotton fabric with the Gel in the desired color. 6. Fold the fabric in one direction from 2 to 3 times, then immediately twist it in order to form a small roll. 7. With the palms of your hands, roll the fabric in spiral vertically on the gel still wet in movements such as if it were a rolling pin. 8. Then slide the jeans roller in both vertical and horizontal direction to complement the drawing. 9. The effect mimics a washed jeans (stained), so the irregular finish and the seams of the 1.10m stripes will give the jeans natural bleaching effect as well as the fabric areas

8 straw Milk Jam Color C166 welcoming, natural For wall preparation: - Suvinil Texturatto Flat in white color - Steel trowel or roller to apply the texture - Soft bristle brush - Sandpaper (nº 360) To make the effect: - Suvinil Acrylic Metalized in the desired color - Low hair wool roller 1. Apply a thin coat of Suvinil Texturatto Flat by using a steel trowel or with the texture application roller. 2. With the texture still wet, slide the soft bristle brush in vertical direction from top to bottom and vice versa all over the wall, creating a scratched surface. 3. Wait for the drying time (24 hours). 4. Sandpaper the surface softly and remove the dust. Note: When sandpapering the texture special care should be taken for not to remove the characteristic reliefs of the final effect. 5. With a low hair wool roller apply 2-3 coats of Suvinil Acrylic Metalized in the desired color

9 lunar Urban Gray Color modernity, technology For preparing the wall: - Suvinil Acrylic Premium or Latex Maxx in white color For texture: - Suvinil Texturatto Flat in white color - Steel trowel - Piece of plastic To make the effect: - Suvinil Acrylic Metalized (in two different colors - tone on tone) - Low hair wool roller - Plastic spatula for putty - Wet fabric 1. Using the wool roller, apply from 2 to 3 coats of Suvinil Acrylic Premium or Latex Maxx on the surface, observing the drying interval. 2. After 24 hours the surface will be completely dry and ready to receive the texture Texture: 3. Apply Suvinil Texturatto Flat with a piece of smashed plastic, making a sponged effect with the texture. The objective is to leave a little product, in a irregular way on the surface. 4. Before the texture begins drying and by using a steel trowel, make the surface smooth softly, lowering the peaks of texture and making a soft relief. 5. Leave to dry for 12 hours. 6. Sandpaper and remove the dust with a wet fabric. 7. With a low hair wool roller apply Suvinil Acrylic Metalized in the clearest desired color. 8. Leave to dry for 6 hours for complete drying. 9. Again, with a wool roller apply Suvinil Acrylic Metalized in the darkest, desired color in a irregular way. 10. With the surface still wet, use a plastic spatula in soft movements spreading the product, removing the excess of the parts on high relief, leaving a little product on low relief, thus creating a contrast between the two surfaces.

10 linen Color C 166 softness, elegance, comfort For preparing the wall: - Suvinil Acrylic Premium Silk Touch white To make the effect: - Suvinil Gel - Soft bristle brush - Cotton fabric for cleaning the brush - Masking tape - Using the wool roller, apply from 2 to 3 coats of Suvinil Acrylic Premium Silk Touch on the surface observing the drying interval. - After 24 hours the surface will be completely dry and ready for the linen effect application. 1. Divide the surface with masking tape on approximately 1.10m width areas. 2. With the wool roller, apply 1 coat of Suvinil Gel. 3. To create the effect, with the gel still wet slide the brush vertically from top to bottom and vice versa. 4. Wait 24 hours for complete drying of the first coat and reapply 1 coat of Suvinil Gel with the roller. 5. Slide the brush once more horizontally this time from left to right and then from right to left across the wall. 6. The linen effect mimics a fabric, so the seam created with the 1.10m area reinforces the idea of the fabric areas. Painting hints: The brush should be cleaned with a cotton cloth after application. When making the corner of the wall, use a paintbrush to apply the gel. Check the package instructions for dilution and drying time. Do a test with the chosen color before you begin working. Side walls should be insulated with a masking tape before you begin working. Regardless of the primer color, the Gel color should always be darker

11 patina Color P 094 welcoming, natural For preparing the wall: - Suvinil Acrylic Premium Silk Touch white To make the effect: - Suvinil Gel - Soft bristle brush - Cotton fabric for cleaning the brush - Using the wool roller, apply from 2 to 3 coats of Suvinil Acrylic Premium Silk Touch on the surface observing the drying interval. - After 24 hours the surface will be completely dry and ready for the patina effect application. 1. With the wool roller, apply 1 coat of Suvinil Gel. 2. To create the effect, with the gel still wet slide the brush vertically from top to bottom and vice versa all over the wall. 3. The patina effect mimics an aged painting, so the irregular effect makes the finish more natural. Painting hints: Work in stripes of approximately 40 cm width so that the gel does not dry before you can make the effect. The brush should be cleaned with a cotton cloth after application. When making the corner of the wall, use a paintbrush to apply the gel. Check the package instructions for dilution and drying time. Do a test with the chosen color before you begin working. The side walls should be insulated with a masking tape before you begin working. Regardless of the primer color, the gel color should always be darker. 1 2

12 crackled classic, delicate Color Capuccino For Texture: - Suvinil Texturatto Flat - Roller for texture application - Brush - Sandpaper (nº 220) To make the effect: - Suvinil Acrylic Metalized - Low hair wool roller Texture: 1. Apply 1 coat of Suvinil Texturatto Flat on the surface with a roller for texture application, making a thin and homogeneous coat. 2. With the texture still wet, use a brush to hit slightly on the surface, creating a low and dotted texture. 3. Wait for the drying time (24 hours). 4. Sandpaper the surface softly and remove the dust. 5. Apply 2-3 coats of Suvinil Acrylic Metalized with a low hair wool roller always observing the drying interval between coats. Painting hints: Before you begin the texture, the surface should be properly prepared. Check the packaging instructions for dilution and drying time. Before you begin painting the side walls should be insulated with masking tape

13 brushed steel modernity, technology Cyber Color For preparing the wall: - Suvinil Acrylic Premium Silk Touch : - Suvinil Acrylic Metalized - Foam roller - Nylon broom - With the wool roller apply two to three coats of Suvinil Acrylic Silk Touch in the desired color on the surface, observing the drying interval. - After 24 hours the surface will be completely dry and ready to receive the effect. 1. With a foam roller, apply one coat of Suvinil Acrylic Metalized. 2. To create the effect, with the acrylic still wet, slide the brush vertically, from top to bottom and vice versa. Hints: You can also create stripes with the metalized effect, in this case, replace the primer by Suvinil Acrylic Metalized. Painting Hints: Clean the brush with the cotton fabric after each application. When making the corner of the wall, use a brush to apply Suvinil Acrylic Metalized. Check the packaging instructions for dilution and drying time. Insulate the side walls with masking tape before you begin working. Work in stripes of approximately 40 cm width in order that Suvinil Acrylic Metalized does not dry before you can make the effect. 1 2

14 marble Color C175 For Texture: - Suvinil Texturatto Special - Steel trowel with rounded corners - Steel Spatula For Polishing: - Wax - Polishing Machine Texture: 1. Apply the texture by using a steel trowel with rounded edges, spreading the texture and making the surface irregular (with small reliefs). 2. After drying the first coat (6 to 8 hours), apply the second coat, supplementing the areas where texture was not applied and leveling the surface. refinement, sophistication, brightness 3. Again, wait for the second coat drying, then apply the third coat, creating stains, leveling and compacting the surface. In this step you ll already have a stained finish. 4. Wait for the drying time of the 3rd coat and apply wax all over the surface by using a trowel and wait for approximately 15 min to this drying. 5. With a polishing machine, make the finish, making the surface polished and shiny. Hints: When creating the effect with the texture try to create low reliefs, using a little texture. Insulate the side walls with masking tape before you start working. Before starting the texture, the surface should be properly prepared

15 Decorative Effects Line. Turn your wall into a true object of decoration. ATTENTION: The colors and effects in this catalog may have slight variations of paint to the finish because it is a decorative painting and printing in offset