Goulds 3296 EZMAG. Lenntech. Chemical Process Pump. Tel Fax
|
|
- Roger Nigel Watkins
- 7 years ago
- Views:
Transcription
1 Goulds 396 EZMAG Chemical Process Pump Lenntech Tel Fax
2 Goulds 396 EZMAG Chemical Process Pump Capacities to 700 gpm (160 m3/h) Heads to 60 ft (189 m) Temperatures to 535 F (80 C) Pressures to 75 PSIG Performance Features Extended Pump Life Sealless design Enclosed impeller Silicon carbide radial and thrust bearings Optional Dryguard bearings for dry run protection Reliable flush circuit Ease of Maintenance Bearing Cartridge design Double-back pull-out Close coupled option on S group ANSI B73.1 dimensional standards No mechanical seal Minimum number of parts Safety Zero emissions One-piece Hastelloy C containment shell Drive and driven magnet clearances protect containment shell Bearing Cartridge design contains bearings in case of failure Adapter drain connection Services: Nitric Acid Heat Transfer Fluids Methylene Chloride Caustic Butodiene Applications: Batch chemical process Rail car or tank unloading Specialty chemicals 396 EZMAG Frame Mounted Design 396 EZMAG Close Coupled Design (S Group Only) Optional casing drain Goulds 396 EZMAG
3 Reliable, Simple, And EZ to Maintain Bearing Cartridge Individual bearings are contained in a single cartridge assembly. Bearings are made of highly abrasion- and corrosionresistant silicon carbide. Dryguard bearings are available for protection against occasional dry run conditions. In the event of bearing failure, the cartridge design contains the bearings and prevents further damage to pump internals. Containment Shell The containment shell is the most important component isolating the pumpage from the atmosphere. The containment shell is a deep-drawn single piece design made from Hastelloy C for reliable corrosion resistance. The vortex-breaking bead at the bottom of the can prevents erosion. Burst pressure is greater than,175 psi. Installation and replacement of bearings is simple. Only one component to install. Maintenance Made Simple The 396 EZMAG was designed with the end user in mind. Fewer parts make planned maintenance faster and easier than other sealless and sealed process pumps. The S group is also available in a close-coupled configuration, further eliminating the need for time-consuming pump and motor alignment. Goulds 396 EZ MAG 3
4 396 EZMAG Options Inducer An optional inducer can reduce the NPSHr by as much as 35-%. This can allow smaller pumps to operate at higher speeds resulting in lower installation costs. Great for media with low NPSHa, high vapor pressures or entrained air. Dryguard Bearings The heat generation from dry run conditions is the number one mode of failure for sealless pumps. Dryguard is a diamond-like carbon that reduces the coefficient of friction by over 70%, enabling short periods of safe operation under dry run conditions. Dryguard is up to X harder than silicon carbide, ensuring its benefits cannot be compromised in even the harshest conditions. High Temperature Applications The 396 EZMAG is ideal for applications up to 535 F. For fluids between 3 F and 535 F, special design considerations are incorporated. A High Temperature ISO Inducer w/seal () bearing cartridge is used to handle the additional rate of thermal expansion. Secondly, Samarium Cobalt magnets are used to ensure performance at elevated temperatures. 4 Goulds 396 EZMAG
5 396 EZMAG Reliable Recirculation Simple, Reliable Recirculation Circuit The 396 EZMAG s reliable flush circuit features patented geometry to ensure the bearings receive proper lubrication. Axial vanes on the driven magnet move fluid around the back of the containment shell. Spiral grooves in the bearing cartridge transport fluid through the cartridge and back into the casing. Bearings stay lubricated and heat resulting from eddy current losses is carried away. Optional Features: Condition Monitoring RTD or Thermocouple Monitors containment shell temperature, provides basic pump protection by indicating system malfunctions such as dry-run conditions, plugged recirculation, flashing of pumpage or decoupling of magnets. Main flow Flush circuit Other Goulds Sealless Process Pumps Model 398/399 Fluoropolymer-lined to handle severe corrosives. Lined pumps provide cost-effective solutions when handling corrosives requiring high alloys. These models feature non-metallic containment shells which eliminate eddy current losses. Model SP398 When suction pressure is negative and air or gases must be evacuated to accomplish pump priming, the SP398 has a self-priming dual volute that primes on demand with only an initial charge of liquid in the casing. Priming is accomplished within the casing, eliminating the need for auxiliary priming systems. Maximum component interchangeability with 398. Model V398 In-line design requires minimal floor space and provides reduced installation costs. Installation is simple because the unit is mounted directly in the line, like a valve. This eliminates the need for field alignment. Maximum component interchangeability with the model 398. Temperature Controller Used to measure signal from containment shell temperature sensor. Has adjustable trip point to sound alarm and/or stop the pump. V Power Monitoring The PS and PS0 Pump Load Monitors measure the motor input power in combination with a proprietary algorithm to accurately determine the pump s power draw. The devices can be set to automatically shut down the pump or warn the operator when upset conditions occur, protecting the pump from damage. 399 SP398 Goulds 396 EZMAG 5
6 Goulds 396 EZMAG Design Features for Maximum Reliability LABYRINTH OIL SEAL Prevents premature bearing failure caused by lubricant contamination and loss of oil. CAST IRON BEARING FRAME Ideal construction for safety and strength. Flood oil lubrication standard, regreaseable bearings optional. Close coupled design is also an option on S Group sizes. OIL SIGHT GLASS For easy monitoring of actual oil level and condition. Bottle oiler is optional. CONTAINMENT SHELL Hastelloy C construction for superior corrosion resistance, high strength, minimal eddy current losses. Deep drawn (one piece) shell for safe, reliable operation. SIMPLIFIED ASSEMBLY AND DISASSEMBLY The number of loose components has been minimized due to its modular design concept. High component interchangeability within the frame size groups. No special tools required. No fitting measurements. Back pull-out design allows for maintenance of the drive side while keeping the liquid end assembled and pressurized. HEAVY DUTY CASING ANSI dimensional 1/8 corrosion allowance Optional tapped connections 6 Goulds 396 EZMAG
7 RARE EARTH MAGNETS Neodymium Iron standard. Optional Samarium Cobalt for higher temperatures. Rare earth material provides high torque capability. BEARING CARTRIDGE Standard pure Silicon Carbide, highly abrasion-resistant with universal chemical resistance. Cartridge design eliminates measurements and fitting for simplified maintenance. Optional Dryguard bearing enables safe operation in temporary dry run conditions. High temperature cartridge is also available. Protects pump internals in the event of a bearing failure. PRESSURIZED RECIRCULATION Dual path internal recirculation prevents vaporization of product in circuit. Ensures lubrication of bearings and continuous cooling of containment shell. ENCLOSED IMPELLER Positively keyed and locked to shaft prevents catastrophic failure due to reverse rotation. Designed for minimum axial thrust, extended thrust bearing life. OPTIONAL INDUCER Reduces the NPSHr by 35 %. Permits smaller pumps at higher speeds = lower costs. Is advantageous for media with gas content. Goulds 396 EZMAG 7
8 Sectional View M Group Frame Mounted 333D A 791D 740B 445A 8 791E 370V 540N 8 9A 33A 1B A C 360A NEAR SIDE 408J 408A NEAR SIDE 370F W 351X 7 740A X S Group Close Coupled S Group 6 Only 371 L 1A 3 E 8 Goulds 396 EZMAG
9 Parts List and Materials of Construction 1 Close Coupled Configuration Only Frame Configuration Only 3 6 S Group Only 4 M Group Frame Configuration Only 5 Carbon-Filled Teflon* for S Group Only 6 Optional Gasket Materials: White Gylon and Fawn Gylon *E.I. DuPont reg. trademark Goulds 396 EZMAG 9
10 Interchangeability Chart Frame-Mounted Units Size Casing Impeller Back Plate Bearing Frame Cartridge Adapter Driven Magnet Drive Magnet Shell Drive Shaft Bearing Frame 1x11/-6 1x11/-6G A A B B 11/x3-6 x3-6 S Group 1x11/-8 C C 1x11/-8H 11/x3-8 x3-8 3x4-7 D D E E F F G G H H I I J J K K 3x4-8G 1x- 11/x3- M Group x3-3x4-11/x3-13 Stub Shaft Close Coupled Units 1x11/-6 A A 1x11/-6G 143 TC 145 TC 18 TC 184 TC 11/x3-6 x TC 15 TC B B 1x11/-8 84 TC 86 TC 1x11/-8H 11/x3-8 x3-8 Goulds 396 EZMAG 54 TC 56 TC C C 84 TSC 86 TSC Motor Adapter Adapter Plate
11 Hydraulic Coverage 3600/900 RPM TOTAL HEAD 3600 RPM (60 Hz) 300 m FT. 0 0 CAPACITY 900 RPM ( Hz) 3 m /h GPM 0 0 1x1.5-6G 3 m /h 1x1.5-8H 1.5x3-1x- 1.5x x3-13 x3-6 x3- x3-8 3x4-8G 3x4-7 3x4- S Group M Group GPM CAPACITY 3600 RPM (60 Hz) FT. FT. 0 0 m 00 5 TOTAL HEAD 900 RPM ( Hz) 1800/14 RPM Capacity 14 RPM ( Hz) 3 m /h m 00 FT. GPM 0 0 S Group M Group FT. 0 m 00 To tal Head 1800 RPM (60 Hz) x x1.5-6G 1.5x3-13 1x1.5-8H 1x- 1x x3-1.5x x3-6 x3-6 x3- x3-8 3x4-8G 3x4-7 3x4-0 5 To tal Head 14 RPM ( Hz) m /h GPM Capacity 1800 RPM (60 Hz) Goulds 396 EZMAG 11
12 Visit our website at Close Coupled Design CP 4.00 DISCHARGE CP 4.00 SUCTION SUCTION X X D D Frame-Mounted Design 3.75 A 4.00 DISCHARGE SUCTION X D *Not to be used for construction. 014 Goulds Pumps, Incorporated A subsidiary of ITT Corporation Lenntech info@lenntech.com Tel Fax Form B396EZMAG 06/14
IMPORTANT SAFETY NOTICE
IMPORTANT SAFETY NOTICE To: Our Valued Customers User safety is a major focus in the design of our products. Following the precautions outlined in this manual will minimize your risk of injury. ITT Goulds
More informationIndustrial Process Pump Safety Manual IMPORTANT SAFETY NOTICE
Industrial Process Pump Safety Manual IMPORTANT SAFETY NOTICE To: Our Valued Customers User safety is a major focus in the design of our products. Following the precautions outlined in this manual will
More informationOHV / OHVL Type OH3 Vertical Inline Pumps ISO 13709 (API 610)
OHV / OHVL Type OH3 Vertical Inline Pumps ISO 13709 (API 610) The Heart of Your Process OHV / OHVL Type OH3 Vertical Inline Pumps ISO 13709 (API 610) OHV OHVL OHV/OHVL Sales Presentation slide
More informationVertical Pumps for the Oil & Gas Industry
Vertical Pumps for the Oil & Gas Industry ITT API Expert ITT Commitment ITT is committed to the Oil and Gas market, which is the largest segment of our business. We have been investing in technology to
More informationGoulds AF. Axial Flow Pump
Goulds AF Axial Flow Pump Goulds AF The Industry Leader in Circulating Pump Technologies Fabricated design 42-66 (1050-1600 mm) (shown with optional spring mounted base) Cast design 6-36 (150-900 mm) Goulds
More informationVERTICAL TURBINE AND PROPELLER PUMPS
VERTICAL TURBINE AND PROPELLER PUMPS INTRODUCTION Vertical Turbine and Propeller Pumps Model 7000 Series Turbine Pump Model 800 Series Axial Flow Propeller Pump Model 800 Series Mixed Flow Propeller Pump
More informationCENTRIFUGAL PUMP OVERVIEW Presented by Matt Prosoli Of Pumps Plus Inc.
CENTRIFUGAL PUMP OVERVIEW Presented by Matt Prosoli Of Pumps Plus Inc. 1 Centrifugal Pump- Definition Centrifugal Pump can be defined as a mechanical device used to transfer liquid of various types. As
More informationPump Division MNR MND. Absorber Recirculation Pumps. Bulletin PS-10-32 (E)
MNR MND Absorber Recirculation Pumps Bulletin PS-10-32 (E) Pump Supplier To The World Flowserve is the driving force in the global industrial pump marketplace. No other pump company in the world has the
More informationHandling Corrosive or Abrasive Liquids
Handling Corrosive or Abrasive Liquids Defining abrasion and corrosion An abrasive liquid is one that has particles in it. Some, like inks, have very fine particles, while others, like some paints, contain
More informationHorizontal Jet Pumps 1/3-1-1/2 HP
Horizontal Jet s 1/3-1-1/2 FW01 0909 Supersedes 0409 The CPJ, CPH and EK models feature the famous Flint and Walling Service Plus motor, available in either NEMA J or Uni-frame flange construction. The
More informationGoulds 3175. Paper Stock/Process Pump with Patented Intelligent Monitoring
Goulds 3175 Paper Stock/Process Pump with Patented Intelligent Monitoring Goulds Model 3175 Designed to Handle the Toughest Jobs in the Pulp & Paper and Process Industries Capacities to 28,000 GPM (6360
More informationAn SPX Process Equipment Operation. Universal II Industrial Series Rotary Positive Displacement ECP Pumps
An SPX Process Equipment Operation Universal II Industrial Series Rotary Positive Displacement ECP Pumps New levels of performance. Reduced operational and maintenance costs. For more than half a century,
More informationModel 362A AURORA. 340A/360A Series SINGLE STAGE END SUCTION PUMPS. www.aurorapump.com
Model 62A MODEL 41A MODEL 44A AURORA 40A/60A Series SINGLE STAGE END PUMPS www.aurorapump.com SINGLE STAGE END PUMPS AURORA 40A/60A Series Single Stage End Suction Pumps Capacities to 4500 G.P.M. (1022
More informationTECHNICAL BROCHURE B5-33GB 5GB, 7GB, 10GB, 18GB, 25GB, 33GB HIGH PRESSURE MULTI-STAGE BOOSTER PUMP
TECHNICAL BROCHURE B-33GB GB, 7GB, 1GB, 18GB, 2GB, 33GB HIGH PRESSURE MULTI-STAGE BOOSTER PUMP FEATURES Multi-stage Design: Provides steady, quiet, vibration free, operation. Optional Stainless Steel Construction:
More informationCRN5-5 A-FGJ-G-E-HQQE 3x230/400 50HZ
GRUNDFOS DATA BOOKLET CRN5-5 A-FGJ-G-E-HQQE 3x23/4 5HZ Grundfos Pump 96517184 Thank you for your interest in our products Please contact us for more information, or visit our website http://www.lenntech.com/grundfos/crn5/96517184/crn-5-5-a-fgj-g-e-hqqe.html
More information300 Series PA Pump and Cooler Assemblies
Type 300 Series PA Sizes 300 thru 370 (Page 1 of 9) 300 Series PA Pump and Cooler Assemblies Pump and Cooler Assemblies with Air/Oil Heat Exchanger When compact gear drives require assistance to dissipate
More informationBOWIE PUMPS OPERATION - MAINTENANCE
BOWIE PUMPS OPERATION - MAINTENANCE PUMPING PRINCIPLE: The meshing owieeof the gears cause a slight depression, with the resulting enmeshing of the gears causing a vacuum drawing the fluid being pumped
More information3196 i-frame. ANSI Process Pump with i-alert Patented Intelligent Monitoring
196 i-frame ANSI Process Pump with i-alert Patented Intelligent Monitoring Proven Performance Over One Million Process Pump Installations Worldwide When the Goulds 196 ANSI Standard Dimension Process Pump
More informationCRN32-2-2 A-F-G-E-HQQE 3x400D 50 HZ
GRUNDFOS DATA BOOKLET CRN32-2-2 A-F-G-E-HQQE 3x4D 5 HZ Grundfos Pump 96122352 Thank you for your interest in our products Please contact us for more information, or visit our website http://www.lenntech.com/grundfos/crn32/96122352/crn-32-2-2-a-f-g-e-hqqe.html
More informationFI Frame-Mounted End Suction Pumps
Water Circulation Pumps & Circulators FI Frame-Mounted End Suction Pumps FI Series Pumps provide the ultimate in reliability and ease of installation for heating, air conditioning, pressure boosting, cooling
More informationHORIZONTAL PUMPING SYSTEM
HORIZONTAL PUMPING SYSTEM BORETS U.S. INC. PERFORMANCE TECHNOLOGY INNOVATION Horizontal Pumping System What is HPS? HPS classification, Pumps, Stages, Impellers, Curves/Performance, Components Why use
More informationIwaki America Is proud to offer the highest value, sealless, non-metallic mag-drive pumps for your chemical process applications. Iwaki America pumps
Iwaki America Is proud to offer the highest value, sealless, non-metallic mag-drive pumps for your chemical process applications. Iwaki America pumps are manufactured solely with nonmetallic wetted parts
More informationSJT / SJM / SJP Large Vertical Pumps
SJT / SJM / SJP Large Vertical Pumps The Heart of Your Process SJT, SJM, SJP Large Vertical Pumps Product Overview SJT Turbine Ns 1800 < 5000 nq 35 < 110 SJM Mixed Flow Ns 5800 < 8300 nq 113 < 161 SJP
More informationBSM MOTOR DRIVEN CENTRIFUGAL PUMPS
PRINCIPLE OF OPERATION A hydraulically and dynamically balanced impeller with raised vane sections discharges liquid as a result of the centrifugal force developed in rotation. The head developed is entirely
More informationHow To Pump A Pump
Multistage Pumps P, PVa, MP 300 Technical Data Performance range: m Capacities up to 1800m 3 /h (8800USgpm) m Head up to 300m (1000feet) m Max. speed up to 1750rpm Multistage pumps of series MP with smaller
More informationElectronic Flow Switches
Industries Electronic Flow Switches Petrochemical Refining Oil Production Water Treatment Pharmaceutical Food and Beverage Pulp and Paper Power Production Gas Processing Mining Biotechnology Semiconductor
More informationMAGNETIC DRIVE SEAL-LESS PUMPS
MAGNETIC DRIVE SEAL-LESS PUMPS MAGNETIC DRIVE SEAL-LESS PUMPS Since 2005, ROTOS DIVISION of GRUPPO ATURIA has developed this extensive program of pumps for industry with a new complete line of SEAL-LESS
More informationN-PUMP SERIES FOR MAXIMUM RELIABILITY AND EFFICIENCY IN WASTEWATER HANDLING. Flygt
N-PUMP SERIES FOR MAXIMUM RELIABILITY AND EFFICIENCY IN WASTEWATER HANDLING Flygt The Concept N-Pump series. Bringing NEW levels of efficiency to wastewater handling applications Reduced pumping efficiency,
More informationHIGH TEMPERATURE TWIN SCREW PUMPS. By: David B. Parker Two Screw Product Engineer IMO Pump Warren Warren, Massachusetts
HIGH TEMPERATURE TWIN SCREW PUMPS By: David B. Parker Two Screw Product Engineer IMO Pump Warren Warren, Massachusetts David B. Parker is the Two Screw Product Engineer for IMO Pump - Warren, in Warren,
More informationThe Company. QUALITY WHICH REDUCES PUMPING COSTS For over 45 years, PAPANTONATOS S.A. has focused on the customer s design,
The Company QUALITY WHICH REDUCES PUMPING COSTS For over 45 years, PAPANTONATOS S.A. has focused on the customer s design, manufacturing and service needs in the field of submersible pumps. Our engineering
More informationPump Specifications 405 Series Commercial Drain Pump (High-Temp) 2 Solids handling
Pump Specifications 405 Series Commercial Drain Pump (High-Temp) 2 Solids handling 405_P1 R1/27/2012 Copyright 2012 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice.
More informationPump Selection and Sizing (ENGINEERING DESIGN GUIDELINE)
Guidelines for Processing Plant Page : 1 of 51 Rev 01 Feb 2007 Rev 02 Feb 2009 Rev 03 KLM Technology #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru. (ENGINEERING DESIGN GUIDELINE)
More informationOil and Coolant Circulating Heating System. Model - OCSM
Oil and Coolant Circulating Heating System Model - OCSM Installation & Operation Manual 216280-000 REV 2 Identifying Your System The HOTSTART heating system is designed to heat fluids for use in marine
More informationPumps SELECTION OF A PUMP
Pumps SELECTION OF A PUMP A water system needs to move the water produced from the source to its customers. In almost all cases in Minnesota, the source is at a lower elevation than the user so the water
More information2" & 3" Poly Wet Seal Pump Instruction Manual
Always place the pump as close to the liquid to be pumped as possible. Keep the suction line short and with few bends. Keep the pump and engine on a level foundation. A poor foundation and a heavy suction
More informationQL Series Vertical, Double-Suction, Twin-Volute Turbine Pumps
QL Series Vertical, Double-Suction, Twin-Volute Turbine Pumps QL QLQ QLC QLQC Experience In Motion Pump Supplier To The World Flowserve is the driving force in the global industrial pump marketplace. No
More informationVertical selfpriming Side-Channel Pumps Type WPV
Vertical selfpriming Side-Channel Pumps Type WPV FIELD OF APPLICATION The side-channel pumps are selfpriming and operate more economically (better efficiency) than normal centrifugal pumps when handling
More informationVogel - Multistage Pumps Design MP, MPA, MPB, MPV Sizes DN 40 - DN 125
Vogel Pumpen Vogel - Multistage Pumps Design MP, MPA, MPB, MPV Sizes DN 40 - DN 125 1 Performance range: Capacities up to 340 m 3 /h (1500 USgpm) Head up to 500 m (1640 feet) Max. speed up to 3600 min
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationPump Specifications 2448LSG, 2448LSGX Series Omnivore 2HP Simplex Grinder Packages
Pump Specifications 2448LSG, 2448LSGX Series Omnivore 2HP Simplex Grinder Packages 2448LSG_P1 R4/2/2012 Copyright 2012 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice.
More information300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS
Section: MOYNO 500 PUMPS Page: 1 of 8 Date: March 1, 1998 SERVICE MANUAL MOYNO 500 PUMPS 300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS Mechanical Seal Models Packing Gland Models MODELS DESIGN FEATURES
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationOwner s Manual. Models: 2S5P & 3S5P OPERATION AND MAINTENANCE OF SELF-PRIMING CENTRIFUGAL TRASH PUMPS PEDESTAL DRIVE
Owner s Manual Models: 2S5P & 3S5P OPERATION AND MAINTENANCE OF SELF-PRIMING CENTRIFUGAL TRASH PUMPS PEDESTAL DRIVE WARNING!! Installation & Operating Instructions Self-Priming Centrifugal Pump DO NOT
More informationPump Specifications 250 Series Submersible Sump / Effluent Pump 2 Solids handling
Pump Specifications 250 Series Submersible Sump / Effluent Pump 2 Solids handling 250_P1 R10/7/2015 Copyright 2015 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice.
More informationMultistage high-pressure multistage centrifugal pumps
Series description Wilo-Helix V 2 4 6 8 Wilo-Helix V 19-27 7 6 6 Hz - North America 22 2 18 5 16 14 4 12 3 1 V 1 V 19 V 27 8 2 6 1 5 1 15 2 25 3 4 2 35Q[US gpm] H[ft] H[m] Design Vertical multi-stage,
More informationLenntech. 1000 psi End port pressure vessels 2.5. User s Guide to: Phoenix Vessel Technology Limited. Model number: 1503
1 User s Guide to: Phoenix Vessel Technology Limited 1000 psi End port pressure vessels 2.5. Model number: 1503 Lenntech info@lenntech.com Tel. +31-152-610-900 www.lenntech.com Fax. +31-152-616-289 Phoenix
More informationImo Pump. www.imo-pump.com. Imo Rotary & Centrifugal Pumps Quick Selection Guide. www.imo-pump.com. The reliable pump people
Imo Pump Imo Rotary & Centrifugal Pumps Quick Selection Guide ALLHEAT series pump in heat transfer fluid service Germany 3G series pump in compressor lube service Buffalo, NY, USA CIG series pumps in hydraulic
More informationFAIRBANKS NIJHUIS FIRE PUMPS. www.fairbanksnijhuis.com
FAIRBANKS NIJHUIS FIRE PUMPS www.fairbanksnijhuis.com FAIRBANKS NIJHUIS Long established as a leading fire pump manufacturer, Fairbanks Nijhuis offers a broad range of horizontal and vertical split case,
More informationTroubleshooting for: Premier Supplier of Pumps & Parts
Premier Supplier of Pumps & Parts Troubleshooting for: 115 Hilton Street West Easton, PA 18042 USA (800)854-0539 fax: (800)926-9508 http://www.processflo.com 4 Operation Pay attention to possible faults.
More informationDelta Power Company 4484 Boeing Drive - Rockford, IL 61109
INDEX Description Page Delta Power Rotary Flow Divider, Positive Displacement (Application Data) 36 P Series, Equal Flow Two Sections 39 P Series, Equal Flow Multi-Sections 40 PM Series, Equal Flow Multi-Sections
More informationPump Maintenance - Repair
Pump Maintenance - Repair Brian Trombly Mo Droppers Cummins Bridgeway, Gaylord, Mi The basic centrifugal pump consists of two main elements: 1. The rotating element which includes an impeller and a shaft.
More informationOUR PRODUCTS TRH-TRS-TRM-TRV. LIQUID RING VACUUM PUMPS AND COMPRESSORS Capacity up to 2100 ACFM Vacuum to 29 Hg. Our Other Products.
Our Other Products OUR PRODUCTS Liquid Ring & Rotary Vane Vacuum Pumps and Systems Liquid Ring Vacuum Pumps: 3 CFM to,000 CFM Liquid Ring Compressors up to 1 psig Heat Transfer Pumps for hot thermal oils
More informationIWAKI MAGNETIC DRIVE PUMPS MDM. Patent JAPAN / U.S.A. / TAIWAN / EU / CHINA
IWAKI MAGNETIC DRIVE PUMPS Patent JAPAN / U.S.A. / TAIWAN / EU / CHINA Magnetic drive process pump resistant to dry run damage The Series of Magnetic drive process pumps have wetted parts made of fluororesin.
More informationextreme applications as standard
grundfos INDUSTRY The insurmountable CR extreme applications as standard THE unsurmountable CR A company you can trust Back in 1971 Grundfos shocked the pump world with the introduction of the CR30 - the
More informationTOPIC: 191004 KNOWLEDGE: K1.01 [3.3/3.5] Which one of the following contains indications of cavitation in an operating centrifugal pump?
KNOWLEDGE: K1.01 [3.3/3.5] P21 Which one of the following contains indications of cavitation in an operating centrifugal pump? A. Low flow rate with low discharge pressure. B. Low flow rate with high discharge
More informationPUMPS TYPE OF PUMP PRESSURE/FLOW RATING CHARACTERISTICS. Centrifugal Low Pressure/High Flow Flow changes when
PUMPS Pumps provide the means for moving water through the system at usable working pressures. The operation and maintenance of these pumps are some of the most important duties for many water utility
More informationDry Pit Solids Handling Pumps
Dry Pit Solids Handling Pumps A Time-Tested Leader Chicago Pump Dry Pit Solids Handling Pumps have an established reputation of efficiency, long life and reliable operation First in: Quality 3Reliability
More informationSUPER-TITAN. Split-case pumps with power, performance and reliability for a world of applications
SUPER-TITAN Split-case pumps with power, performance and reliability for a world of applications The Prestige. The Performance. SUPER-TITAN PUMPS Features The TKL Super-Titan pump makes a significant contribution
More informationRPT SIGMA PUMPY HRANICE ROTARY LOBE DISPLACEMENT PUMPS 426 2.98 23.01
SIGMA PUMPY HRANICE ROTARY LOBE DISPLACEMENT PUMPS RPT SIGMA PUMPY HRANICE, s.r.o. Tovární 605, 753 01 Hranice, Czech Republic tel.: +4 581 661 111, fax: +4 581 602 587 Email: sigmahra@sigmahra.cz 426
More informationTECHNICAL INFORMATION Bulletin
Peerless Pump Company 2005 Dr. M.L. King Jr. Street, P.O. Box 7026, Indianapolis, IN 46207-7026, USA Telephone: (317) 925-9661 Fax: (317) 924-7338 www.peerlesspump.com www.epumpdoctor.com TECHNICAL INFORMATION
More informationFlygt N-Pumps 3085, 3102 & 3127. For reliable and efficient wastewater handling
Flygt N-Pumps 3085, 3102 & 3127 For reliable and efficient wastewater handling The Concept Flygt N-Pump series Reduced pumping efficiency, high energy and maintenance costs shouldn t be a fact of life
More informationEnergy Recovery Device isave 21-40
Data sheet Energy Recovery Device isave 21-40 Lenntech info@lenntech.com Tel. +31-152-610-900 www.lenntech.com Fax. +31-152-616-289 Table of Contents 1. General information....3 2. Benefits...3 3. Technical
More informationInstallation, Operation, Repair and Parts Manual
Description Series 9700 Close-Coupled AC Motor-Driven and Pedestal Mount Centrifugal Pumps Installation, Operation, Repair and Parts Manual Form L-0350C Rev. B Hypro's 9700 series pumps are specifically
More informationMOBILE FIRE - RESCUE DEPARTMENT FIRE CODE ADMINISTRATION
MOBILE FIRE - RESCUE DEPARTMENT FIRE CODE ADMINISTRATION Fire Pump Plan Review 2009 International Fire Code and NFPA 20 Date of Review / / BLD201 - Project Address: Project Name: Contractor s Business
More informationUniquely designed and engineered specifically for the pulp and paper industry.
Universal SPU2 Series Uniquely designed and engineered specifically for the pulp and paper industry. For more than half a century, Waukesha Cherry-Burrell has been a leader in the design, manufacturing
More informationZOP, ZOT SIGMA PUMPY HRANICE GEAR PUMPS 426 1.99 21.04
SIGMA UMY HRANICE GEAR UMS SIGMA UMY HRANICE, s.r.o. Tovární 605, 753 01 Hranice, Czech Republic tel.: +420 581 661 111, fax: +420 581 602 587 Email: sigmahra@sigmahra.cz, 426 1.99 21.04 Application In
More informationOPERATION & MAINTENANCE MANUAL. for VERTICAL INLINE PUMPS
OPERATION & MAINTENANCE MANUAL for VERTICAL INLINE PUMPS PATTERSON PUMP COMPANY A SUBSIDIARY OF THE GORMAN-RUPP COMPANY PO Box 790 9201 Ayersville Road Toccoa, Georgia 30577 Telephone: 706-886-2101 SAFETY
More information4" SUBMERSIBLE PUMPS
4" SUBMERSIBLE PUMPS 4" SUBMERSIBLE PUMPS 50/60 HZ Multi-stage centrifugal submersible pumps for clean water in 4" wells. The 4" VSP pump series is carefully designed and manufactured for maximum resistant
More informationFire Pump Plan Review March 2010
Fire Pump Plan Review March 2010 Date of Review: / / Permit Number: Business/Building Name: Address of Project: Designer Name: Designer s Phone: Contractor: Contractor s Phone: Occupancy Classification:
More informationBASIS RANGE TMB SERIES
BASIS RANGE SERIES magnetic driven pumps BASIS The pumps belong to Argal s BASIS range and feature, single stage, centrifugal impeller and magnetic drive. The range of pumps includes five models to deliver
More informationSVA SIGMA PUMPY HRANICE SELF PRIMING PUMPS 426 2.98 16.05
SIGMA PUMPY HRANICE SELF PRIMING PUMPS SVA SIGMA PUMPY HRANICE, s.r.o. Tovární 605, 753 01 Hranice, Czech Republic tel.: +40 581 661 111, fax: +40 581 60 587 Email: sigmahra@sigmahra.cz 46.98 16.05 Applications
More informationTransfer Pump Selection
Transfer Pump Selection Material Options: TRANSFER PUMPS Aluminum Cast Iron Polypropylene Typical Use: Water Transfer The aluminum construction does not lend itself well to chemical transfer. Options include:
More informationYour Partner for Concentrated Solar Power Generation The Heart of Your Process
1 Sulzer Pumps Your Partner for Concentrated Solar Power Generation The Heart of Your Process 2 Experience and Solutions You Can Rely on Around the world, the power industry is taking on the challenge
More informationPipe Cutting and Beveling Clamshells
Pipe Cutting and Beveling Clamshells Who We Are One Company, Total Support, Complete Solutions For more than a century, Hydratight has provided world-class bolted joint solutions and continues to set international
More informationsealed close coupled pumps
sealed close coupled pumps centrifugal self-priming 1 - and are different configurations of the same range of centrifugal axle pumps, self-priming which offers reliability in use. Specifically designed
More informationRental Services Temporary Cooling - Flexible Water Hose
Engineering Bulletin Rental Services Temporary Cooling - Flexible Water Hose September 2006 CHS-PRB007-EN Warnings and Cautions Warnings and Cautions. Notice that warnings and cautions appear at appropriate
More informationIWAKI MAGNETIC DRIVE PUMPS MDM. Patent & Pat.Pend. JAPAN / U.S.A. / EU / CHINA / TAIWAN
IWAKI MAGNETIC DRIVE PUMPS Patent & Pat.Pend. JAPAN / U.S.A. / EU / CHINA / TAIWAN Magnetic drive process pump resistant to dry run damage The Series of Magnetic drive process pumps have wetted parts made
More informationENGINE COOLING SYSTEM
ENGINE COOLING SYSTEM 1988 Toyota Celica 1987-88 TOYOTA Engine Cooling Systems Celica DESCRIPTION The basic liquid cooling system consists of a radiator, water pump, thermostat, cooling fan, pressure cap,
More informationCENTRIFUGAL PUMP SELECTION, SIZING, AND INTERPRETATION OF PERFORMANCE CURVES
CENTRIFUGAL PUMP SELECTION, SIZING, AND INTERPRETATION OF PERFORMANCE CURVES 4.0 PUMP CLASSES Pumps may be classified in two general types, dynamic and positive displacement. Positive displacement pumps
More informationAxial and Mixed Flow Pumps for Large Volume Pumping
Vertical Industrial and Process Axial and Mixed Flow for Large Volume Pumping Encased (Can ) Water and Process Liquid Vertical Turbine for Water Supply from Drilled Wells Vertical close coupled single
More informationHPT High Speed Boiler Feedwater Pumps
HPT High Speed Boiler Feedwater Pumps The Heart of Your Process Types of Boiler Feedwater Pumps Diffuser Casing Segmental Ring Volute Casing Horizontal Split Diffuser Casing High Speed Barrel Casing HPT
More informationOPERATING AND MAINTENANCE INSTRUCTIONS PUMP TYPE 215.10
OPERATING AND MAINTENANCE INSTRUCTIONS PUMP TYPE 215.10 To Pump model Pump number Our order Your order Order date Reference Item number Destination Plant Before storing, installation, operation or maintenance
More informationPUMP AND MOTOR DIVISION
INSTALLATION MANUAL SERIES P2 and P3 MOBILE PISTON PUMP 1 Check model code / compare with your paper work Nameplate of the pump Ordering / Sales Acknowledgement 2 Check rotation of the pump Clockwise rotation
More informationAC Electric Motors best practice
If you want to learn more about best practice machinery maintenance, or world class mechanical equipment maintenance and installation practices, follow the link to our Online Store and see the Training
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17)
17 Engine-Lubrication (Page GR-17) Lubrication system components, removing and installing Oil filter housing, disassembling and assembling Oil pan, removing and installing Oil pressure and oil pressure
More informationAir Eliminators and Combination Air Eliminators Strainers
Description Air Eliminators and Combination Air Eliminator Strainers are designed to provide separation, elimination and prevention of air in piping systems for a variety of installations and conditions.
More informationSERIES ASM NEOPRENE/EPMD FLANGED SINGLE SPHERE CONNECTOR CONNECTORS. Pressures to 225 PSIG (15.51 barg) Temperatures to 230ºF (110ºC)
APPLICATIONS Process Industry Weak Acids Alkalies Compressed Air Pulp & Paper MODELS ASM - Flanged Connection OPTIONS Control Rods Oil & Gas Water & Waste Pump suction & discharge Sea water Chemical lines
More informationMEMBRANE VACUUM MINI PUMPS
MEMBRANE VACUUM MINI PUMPS The mini pumps described in this page are membrane-type. They can be used both as vacuum pumps and compressors. In the latter version they can supply compressed air 100% oil-free
More informationModel series CAM / CAM-Tandem
P R O D U C T I N F O R M A T I O N Multistage canned motor pumps Model series CAM / CAM-Tandem Contents Description Description... 2 Application and insertion... 4 Functional principle and materials...
More informationPump Shaft Sleeves - Stratford Engineering
Pump shafts are usually protected from erosion, corrosion, and wear at seal chambers, leakage joints, internal bearings, and in the waterways by renewable sleeves. The most common shaft sleeve function
More informationCirculation Systems for Single and Multiple Seal Arrangements-Part Three
Circulation Systems for Single and Multiple Seal Arrangements-Part Three Gordon Buck and Ralph Gabriel, John Crane Inc. Conclusion of our series covering applications in which they are used, why they are
More informationOil Sight Glass BENEFITS
8 L-4090 Schroeder es provide maintenance and lubrication management professionals a complete and immediate visual oil analysis. Constructed of durable cast acrylic, they withstand most petroleum products
More informationExample. Fluid Power. Circuits
Example Fluid Power Circuits To Enhance Symbol Reading Skills To Work On Circuit Reading Skills With Answers HI LO Pump Circuit 18 A1 B1 17 16 15 13 Set 14 2,000 PSI PG2 Set 500 PSI 12 11 7 8 10 PG1 9
More informationMechanical Seal Piping Plans
Mechanical Seal Piping Plans Single Seals plans 01, 02, 03, 11, 13, 14, 21, 23, 31, 32, 41 Dual Seals plans 52, 53A, 53B, 53C, 54, 55 Quench Seals plans 62, 65A, 65B, 66A, 66B Gas Seals plans 72, 74, 75,
More informationPower Recovery Turbines
Power Recovery Turbines Fixed and Variable Geometry Vertical Horizontal Bulletin PS-90-1 (E) Pump Supplier To The World Flowserve is the driving force in the global industrial pump marketplace. No other
More informationPump and Valve Components and Maintenance
Pump and Valve Components and Maintenance Outline: 1. Split case and End Suction pumps, industry in the 21 st century, cost of ownership, and performance tips 2. Split case Pumps features, maintenance,
More informationRexroth Hydraulic Pump A10VO Series User Manual
Rexroth Hydraulic Pump A10VO Series User Manual Rexroth Hydraulic pump A10VO Series User Manual Revised 5/1/2009 Page 1 of 12 Functional Purpose This pump is preferred over a fixed displacement (gear)
More informationVolkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pan, removing and installing Oil pressure and oil pressure switch, checking Dynamic oil pressure warning
More informationModel 413 AURORA. 410 Series SINGLE STAGE SPLIT CASE PUMPS WWW.AURORAPUMP.COM
Model Model AURORA Series SINGLE SAGE SPLI CASE PUMPS WWW.AURORAPUMP.COM SINGLE SAGE SPLI CASE PUMPS AURORA Series Single Stage Split Case Pumps Capacities to 00 GPM (0 m /hr) Heads to Ft. (0 m) emperatures
More information