REQUEST FOR PROPOSAL FOR Supply and Installation of Wireless Access Point in the following location

Transcription

1 REQUEST FOR PROPOSAL FOR Supply and Installation of Wireless Access Point in the following location General Scope of Work: Supply and Installation of Wireless Access Point in the following location. Locations of Installation: Computer & Statistical Service Centre, 4 th Floor, S.N. Bose Bhaban ISI Kolkata, 203 B.T. Road, Kolkata , West Bengal, INDIA BILL OF MATERIALS Sl. No. Item Qty. (Nos.) 1 Access Point 8 2 Dual-band Dipole Antena ( 2.4GHz and 5 GHz) year Support for all active components 1

2 DETAIL SPECIFICATION: Access Point specifications Should support 4x4 MIMO. Should have ac support. Should provide support for 1.3gbps. The access point should be managed & monitored through a centralized controller. Should support three spatial streams. Should be able to intelligently collaborate in real-time to allow more users to connect with optimized signal quality and performance. Should ensure client association with the best AP offering the best data rate available. Should have the capabilities to improve downlink performance to all mobile devices, including one-, two-, and three-spatial-stream devices on ac while improving battery life on mobile devices such as smartphones and tablets. Should have 80Mhz channel support. Should provide proactive, high-speed spectrum intelligence across 20-, 40-, and 80-MHz-wide channels to combat performance problems due to wireless interference. Should have the capabilities for MIMO equalization to optimize uplink performance and reliability by reducing the impact of signal fade. Should support external antennas n version 2.0 (and related) capabilities n and a/g beamforming 20- and 40-MHz channels PHY data rates up to 450 Mbps (40 MHz with 5 GHz) Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx) dynamic frequency selection (DFS) Cyclic shift diversity (CSD) support ac Wave 1 capabilities 4x4 MIMO with three spatial streams MRC ac beamforming 20-, 40-, and 80-MHz channels PHY data rates up to 1.3 Gbps (80 MHz with 5 GHz) Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx) DFS CSD support Data rates supported a: 6, 9, 12, 18, 24, 36, 48, and 54 Mbps

3 802.11g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps Maximum number of nonoverlapping channels 2.4 GHz b/g: 20 MHz: n: 20 MHz: 3 5 GHz a: 20 MHz: n: 20 MHz: MHz: ac: 20 MHz: MHz: 9 80 MHz: 4 Maximum transmit power 2.4 GHz b g n (HT20) 5 GHz

4 802.11a n (HT20) n (HT40) ac non-ht80: 23 dbm, 4 antennas VHT20 23 dbm, 4 antennas VHT40: 23 dbm, 4 antennas VHT80: 23 dbm, 4 antennas VHT20-STBC: 23 dbm, 4 antennas VHT40-STBC: 23 dbm, 4 antennas VHT80-STBC: 23 dbm, 4 antennas Should support Certified for use with antenna gains up to 6 dbi (2.4 GHz and 5 GHz) external antennas. Should have 10/100/1000BASE-T autosensing (RJ-45) & Management console port (RJ-45) Should have 512 MB DRAM & 64 MB flash. Should support PoE & Local Power supply. Should support external module for Wireless Security. Should support 802.3at & af. Should comply to the following standards:- UL CAN/CSA-C22.2 No UL 2043 IEC EN EN 50155

5 Radio approvals: FCC Part , RSS-210 (Canada) EN , EN (Europe) ARIB-STD 66 (Japan) ARIB-STD T71 (Japan) EMI and susceptibility (Class B) FCC Part and ICES-003 (Canada) VCCI (Japan) EN and -17 (Europe) EN EMC requirements for the Medical Directive 93/42/EEC Should support following IEEE standards: IEEE a/b/g, n, h, d IEEE ac Draft 5 Should have following Security standard: i, Wi-Fi Protected Access 2 (WPA2), WPA 802.1X Advanced Encryption Standards (AES), Temporal Key Integrity Protocol (TKIP) Should support Extensible Authentication Protocol (EAP) types: EAP-Transport Layer Security (TLS) EAP-Tunneled TLS (TTLS) or Microsoft Challenge Handshake Authentication Protocol Version 2 (MSCHAPv2) Protected EAP (PEAP) v0 or EAP-MSCHAPv2 EAP-Flexible Authentication via Secure Tunneling (FAST) PEAP v1 or EAP-Generic Token Card (GTC) EAP-Subscriber Identity Module (SIM) Should have following Multimedia support: Wi-Fi Multimedia (WMM)

6 Consortium: If the Bidder is not a manufacturer he should provide documentary evidence (e.g. Manufacturers Authorization Form) for having tied up with all the participating agencies. Tax and Duty Exemption: The Institute may provide necessary certificates for tax/duty exemption as applicable. Bid Currencies: Bids are to be quoted in Indian Rupees only. Cancellation of Tender: 1. The Institute may cancel the tender processing at any point of time prior to the issuance of purchase order without assigning any reason whatsoever for unforeseen and unavoidable circumstances. 2. The Institute may also cancel the tender processing for want of any participating Bidder or if all the participating Bidders fail to qualify eligibility in terms with technical or other reasons. Technical (Including services) & commercial bids should be submitted in separate sealed envelopes mentioning the contents on it. Any Technical Bid not containing the above specifications may be rejected. The Technical Bid should not contain any price information, such proposal will be rejected.

7 Bill of Material (To be included in Technical Bid) The Bidder should provide Bill of Material (details of all Modules / Components of Software including those bought-out, off-the-shelf or third-party products / items required) Module-wise, in the following format. Module/Item Description Make/ Model/ Version Part Number Principal Vendor/ Manufacturer Quantity/ No. of Licenses per installation Signature of Bidder : Name : Business address : Place : Date :

8 Bill of Material (To be included in Commercial Bid) Module/ Item Make/ Model/ Version Part Number Principal Vendor/ Manufacturer Quantity/ No. of Licenses per installation Unit Price Total Price without Tax Tax % Tax Estimate Total Price with Tax Signature of Bidder : Name : Business address : Place : Date :

9 Quotation Address : To The Head Computer & Statistical Service Centre, 4th Floor, S.N.Bose Bhaban Indian Statistical Institute 203 B.T. Road, Kolkata