The QUICKEST way to wire. For recessed-ceiling, open-ceiling and power applications.

Transcription

1 T h e # 1 S e l l i n g M o d u l a r W i r i n g S o l u t i o n S i n c e The QICKEST way to wire. For recessed-ceiling, open-ceiling and power applications.

2 the RELOC Advantage Innovative, patented products Fast estimating and simple ordering Lowest total job cost Easy fixture relocation Easy project management Safety and reliability RELOC Wiring Solutions In today s fast-paced construction market, staying on schedule and under budget is tougher than ever. Every job demands wiring solutions that reduce installation time and adapt to changes, whether they occur during construction or after a building is occupied. With rising labor costs and the shortage of qualified electricians, traditional wiring methods no longer measure up. RELOC Wiring Solutions from Acuity Brands Lighting has been the leader in modular wiring since Reloc offers three unique wiring systems that are fast, easy and effective: Quick- wiring for recessed ceiling lighting installations, OnePass system for open-ceiling lighting installations and System 820 for specialty lighting and power applications.

3 Reduce, Reuse, Recycle...RELOC REDC E SE RE Y REC CLE RELOC products are a greener solution than traditional wiring. RELOC products minimize installation time and construction waste while maximizing productivity, reusability and the use of recycled materials. Please see for more information. Lowest Total Job Cost Easy Fixture Relocation RELOC components snap together in a frac- Complete tion of the time it takes to wire a fixture with and inexpensively by reusing RELOC conventional wiring methods and require components. Simply unplug the original less labor and fewer materials. Installation system, time is reduced by up to 66 percent, result- reconnect the system. Quick changes ing in significantly reduced total job cost. minimize facility down-time. Easy Project Management Safety and Reliability RELOC wiring enhances the ability to All RELOC components are 100-percent plan and manage a tight schedule. Since electrically tested. Safety features such RELOC wiring is installed with fixtures in as dead-fronted contacts are designed to the finish phase, labor, material costs and comply with L183 and CSA trade conflicts are reduced during the (standard for manufactured wiring sys- critical rough-in stage. tems) and 2008 NEC (G) and wiring relocate changes the quickly fixtures and Quick- OnePass CEC (ballast disconnective means) Fast Estimating and Simple Ordering while following standard safety practices. RELOC estimating tools provide fast project System 820 estimates and simple ordering, eliminating the need for time-consuming factory drawings. RELOC Wiring Offers Lowest Total Job Cost vs. Traditional Wiring Methods Manufactured wiring systems are described in NEC 604 and Canadian CEC All products are L Listed, NYC Approved and C-L Listed or CSA Certified. New York City Approved Calendar Numbers 47802, and ONE

4 Quick- recessed-ceiling wiring is faster and easier to install than MC Cable or other modular wiring systems. With three basic components, the Quick- system snaps together in a fraction of the time it takes to wire a fixture with MC Cable. There is no need for tools, factory estimating or drawing services. Due to faster installation, labor costs are dramatically reduced, cutting down the total job cost. The Quick- system is ideal for wiring lay-in troffers, parabolics, downlights, indirect fixtures and emergency lighting equipment in office buildings, schools and retail stores. Quick- Standard Features The Quick- fixture combo is shipped standard with an access plate (as shown in the photo below). These access plates have one pre-punched knockout to speed the installation of Lithonia troffers and parabolics. For downlights or non-lithonia fixtures, discard access plate and install fixture cable directly to any 1/2 knockout. L Listed autoground Fixtures are grounded automatically as soon as the access plate is snapped in place. No ground leads to connect. Auto-latching springs allow for an easy, secure connection and prevent accidental disengagement. Factory-Installed Combo Option The Quick- fixture cable (QFC) can be prewired to the fixture in the factory. Both the fixture and Quick- cable are shipped together. This reduces the amount of time spent sorting materials at the job site. It also cuts on-site disposal costs. This option is ideal for jobs with 100 or more fixtures of the same type, using the same Quick- fixture cable. See page 3 for ordering information. Ask your local Acuity Brands Lighting representative for your RELOC price guarantee. TWO 2 Quick- Wiring is Easy to Estimate 1) One QFC cable per fixture 2) One QC converter per circuit run 3) 10% QE cables and 3% QS splitters (spare parts) Dust covers are not included with combo option and must be ordered separately.

5 Switching Solutions If MC Cable is used between switches, Quick- wiring can provide a simple and efficient link from the switchbox to the fixtures on the switched circuit. For best results, install Quick- switch drops during the rough-in stage. Add a Quick- extender between the switch drops during the finish phase when the fixtures and QFC cables are installed. 35% Cost Savings = MC Cable Quick- Materials $ $ Labor $ $ Total* $ $ * Based on a typical single-circuit, 30-fixture application on 10-foot centers with a $55/hr. labor rate (SD). 35% Savings On Total Installed Cost How To Order Fluorescent Combo Option Lithonia Lighting fixture with Quick- fixture cable attached and prewired. Example: RELOC QFC becomes luminaire option QFC311GAB 2SP8 G 3 32 A GEB10IS QFC311GAB Specifying wiring option: Wiring Option 2 conductors (1 hot) ex: QFC2 (length) xx 3 conductors (2 hot) ex: QFC3 (length) xx A All ballasts/inverters on "A" circuit. B All ballasts/inverters on "B" circuit. AB Outboard lamps on "A", inboard on "B" (If fixture contains 2 ballasts plus an inverter, the inverter will be located at the access plate. Not connected to a QFC supplied circuit.) AE NW Access plate with knockouts installed in fixture. RELOC included with fixture, not wired. All ballast(s) on "A", inverter on "B". Access plate with knockouts installed in fixture. RELOC included with fixture, not wired. 3 THREE

6 OnePass open-ceiling wiring simplifies the installation of high bay fixtures. Traditional hardwiring requires three or more passes to install conduit, pull wire and hang fixtures. sing the OnePass system, three basic components and one pass are needed. Faster installation reduces labor costs and the total job cost. Plus, there is no need for factory estimating or drawing services. The OnePass system is ideal for installing HID and fluorescent fixtures in manufacturing facilities, warehouses, retail facilities and any other open-ceiling fixture applications. OnePass Standard Features The OnePass system is listed for open accessible ceilings and dry locations, meeting or exceeding the L 183 and requirements, the National Electrical Code and Canadian Standards. All components are easy to install and relocate, featuring easy-to-grip cable heads and self-latching springs that simply plug together. OnePass Factory-Installed Option se the following guidelines to order fixtures with OnePass pre-installed. Add OCS to the description: Example IB LP835A OCS. Consult factory for other options. For four or five conductor fixture drops, follow the same guidelines as above, except tap positions must now be specified for the OC product. Example: OC122N = 5' white cord with two hots, two dedicated neutrals and a ground. Example: OC2310 = 10' white cord with two hots and one neutral. OnePass wiring is rated at 20A with 90ºC 12 AWG conductors. The OnePass OC2 cable also is available in a 10AWG, 20A option to reduce voltage drop on longer runs. All components are keyed to prevent different voltages from connecting, and color-coded cable heads allow for easy identification. 25% Savings On Total Installed Cost FOR 4

7 NEW Circuit Selection at Every Fixture Position 1 G N The OCS is a polarized plug-in connection for industrial fixtures, featuring a patented thumbslide action. Just choose the desired hot conductor(s) needed to energize each fixture. Simply slide the circuit selector to position 1, 2 or 3 and plug the fixture into the system. No more worrying about coordinating different-circuited fixtures. The OCS permits removal of any fixture from the branch circuit without additional components or interruption in the branch circuit. All cables now available in custom colors. For details, contact the factory at % Cost Savings = Pipe & Wire OnePass Materials $ $ Labor $ $ Total* $ $ * Based on a typical single-circuit, 30-fixture application on 20-foot centers with a $55/hr. labor rate (SD). Ask your local Acuity Brands Lighting representative for your Reloc price guarantee. OnePass Wiring is Easy to Estimate 1) One OCS per fixture 2) One OC2 cable for each fixture 3) One OC per circuit run 5 FIVE

8 Quick- Components Recessed-Ceiling Lighting System Example: QC120 QC - Converter Provides interface between hardwiring and Quick- wiring at the homerun location. QC QC Quick- converter QSFC - Starter Fixture Cable 1 Combination of converter (QC) and fixture cable (QFC). QSFC QSFC Quick- starter fixture cable 12/2G Length feet feet Optional ground lead G No. 18 AWG ground lead dropped to fixture (REQIRED IN CANADA) QFC QFC - Fixture Cable 1 Male/female cable provides power from fixture to fixture. Access plate is preattached. QFC Quick- fixture cable 12/2G Length feet feet Optional ground lead G No. 18 AWG ground lead dropped to fixture (REQIRED IN CANADA) QE QE - Extender Male/female cable provides additional length anywhere within the system. QE Quick- extender 12/2G Length feet feet QSD - Switch Drop Provides local switched power for fixtures as well as the ability to carry on unswitched power through the use of a QE. QSD QSD Quick- switch drop 1LEVEL 2LEVEL 1LEVEL/N Length 01 1 foot QPT - Power Tee Provides hardwire connection to any electrical device. QPT QPT Quick- power tee Length 01 1 foot QS - Splitter Male/female component that can be used anywhere in the system. Separates branch circuit into two directions. QS QS Quick- splitter SIX 6 Quick- Dust Cover Dust cover is required to protect unused ports in a RELOC system per NEC Article QICK FLEX Dust cover J50 NOTES: 1 Furnished with poke home connectors for easy connection to fixture wires.

9 OnePass Components Open-Ceiling Lighting System Example: OC 277 OSC2 1 OSC2 OnePass starter cable OC2 1 OC2 OnePass twoport cable OC 1 OC OnePass converter 12/2G 10/2G 10/3G 10/4G 12/2G 10/2G 10/3G 10/4G feet feet feet feet feet feet OC - Converter Provides interface between hardwiring and RELOC wiring at homerun location. OSC2 - Starter Cable Provides interface between hardwiring and RELOC wiring system. OC2 - Two-Port Cable Provides feed-through and tap in one component. Acts as an extension cable between fixture connections. OCS 4 OCS OnePass cord with circuit selector 05 5 feet feet feet Cord colors 5 WH White cord BK Black cord OCS - Circuit Selector A polarized plug-in connector for industrial fixtures. Allows on-site circuit selection of desired hot conductor(s). Prewired by fixture manufacturer or field installed by contractor. OC 1,4 OC OnePass cord unselectable OD 1 OD OnePass drop cable Tap position TAP2 2 TAP12 1 and 2 TAP34 3 and 4 TAP1 1 TAP3 3 TAP23 2 and 3 TAP123 1, 2 and 3 OSS 1 OSS OnePass splitter splice 05 5 feet feet feet 12/2G Cord colors 5 WH White cord BK Black cord 05 5 feet feet feet 3 OC - Cord nselectable A polarized, non-circuit selectable plug-in connection for industrial fixtures. Prewired by fixture manufacturer or field installed by contractor. OD - Drop Cable Allows miscellaneous devices (exits, etc.) to become part of the system. OSS - Splitter Splice Male/female component that can be used anywhere in the system. Separates branch circuit into two directions. OnePass Dust Cover Dust cover is required to protect unused ports in a RELOC system per NEC Article RDC3 METAL Dust cover CSA/L J50 NOTES: 1 For two neutral applications, specify 2N (10/4G and ). Consult factory for other options. 2 Please consult factory when ordering 208V, 240V or 480V. 3 se product for 10GA, 20A systems. 4 16AWG rubberized cord rated for 600V, 105ºC with fully rated ground conductor. 5 White cord standard. Black cord requires longer lead time. 7 SEVEN

10 System 820 Specialty Power and Lighting System Example: CD 120 F CD - Circuit Distributor Provides interface between hardwiring and RELOC wiring system. CD CD No. of conductors D Three E Four IGW Isolated ground wire; available with 120V and F conductor CE - Cable Extender Male/female cable that provides additional length anywhere throughout the RELOC system. CE CE No. of conductors D Three E Four Factory keying Cable length feet feet feet IGW Isolated ground wire; available with 120V and F conductor SSC - Standard Selector Cable Male/female cable, provides power from fixture to fixture. Attaches to access plate or through 1/2 trade-size knockout by means of poke home connectors. SSC SSC No. of conductors D Three E Four Factory keying Cable length feet feet G Ground lead with lug terminal (REQIRED IN CANADA) SS - Splitter Splice sed to split branch circuit into two directions in commercial or power applications. SS SS F No. of conductors Factory keying IGW Isolated ground wire; available with 120V and F conductor CS - Circuit Selector nit Provides wiring of any device through 1/2" trade-size knockout. CS uses No. 12 AWG leads, allowing full circuit access. CS CS F No. of conductors Factory keying IGW Isolated ground wire; available with 120V and F conductor 820 Dust Cover Dust cover is required to protect unused ports in a RELOC system per NEC Article RDC3 METAL Dust cover CSA/L J50 EIGHT 8

11 System 820 Specialty Power and Lighting System DP 120 A Number of duplexes (blank) One 2 Two Series DP Interface component PT Power tee 1 DC Drop cable No. of conductors D Three E Four Hot receptacle position 1 One 2 Two 3 Three Drop type A Armored Cable length 01 1 foot 05 5 feet IGW Isolated ground wire; available with E and F conductors (add if required) DP - Duplex Receptacle The DP is a prewired power receptacle outlet box that integrates with a RELOC system. The DP can be used to manage phase loading on power receptacle applications. Pre-order the appropriate number of receptacles for each circuit prewired from the factory. PT PT F No. of conductors 1 Tap position and and and , 2 and 3 A Drop type A Armored Cable length 01 1 foot 03 3 feet IGW Isolated ground wire; available with 120V; E and F conductors PT - Power Tee Provides hardwire connections to any electrical device. RRCA RRCA V V F 05 WH No. of conductors Tap position 123 1, 2 and 3 (120V or 277V) , 2, 3 and 4 (208V or 480V) 05 5 feet Cord color WH White RRCA - Replacement RELOC Cord Assembly Ideal for retrofitting projects done with old RELOC system. Prewired by fixture manufacturer or field installed by the contractor. DC DC No. of conductors D Three E Four Factory keying feet feet IGW Isolated ground wire; available with 120V and F conductor DC - Drop Cable Provides integration of other electrical devices into the 820 system, such as power outlets and power strips. NOTES: 1 Power Tee (PT) is available in five-conductor with DP product. 2 RRCA is sold with white cord and five-wire configuration. 9 NINE

12 RECYCLE RESE REDCE Reduce, Reuse, Recycle...RELOC RELOC products are a greener solution than traditional wiring. RELOC products minimize installation time and construction waste while maximizing productivity, reusability and the use of recycled materials. Please see for more information. One Lithonia Way, Conyers, GA TEL FAX Acuity Brands Lighting, Inc., All Rights Reserved. 06/11 R6980 Form No