Pro/ENGINEER Wildfire 2.0 With Integrated Pro/MECHANICA. Tutorial 3: Modeling L-Shaped Rod and Performing Finite Element Analysis using Pro/MECHANICA

Transcription

1 MAE 244 : Dynamics and Strength Laboratory Fall 2005 Tutorial Material for Pro/ENGINEER Wildfire 2.0 With Integrated Pro/MECHANICA Tutorial 3: Modeling L-Shaped Rod and Performing Finite Element Analysis using Pro/MECHANICA Chuanyu Feng, PhD chuanyufeng@yahoo.com

2 Introduction This tutorial is similar to Tutorial 2. The difference is that, in this part, you will use Sweep feature to make an L-Shaped Rod, and then apply proper boundary conditions and loads to analyze it. Create an L-Shaped Rod In this session, you will make a simple Pro/E part, and further practice the basic modeling technique: sketching and sweep. Starting Pro/E and Creating new Part 1. Start Pro/E Wildfire. 2. Click menu: File New. A dialog will pop up (Figure 1) 3. Give a new name and/or description if desired. 4. Click OK button and Pro/E will create an empty solid part as shown in Figure 2. Figure 1. New Dialog Chuanyu tony Feng 2

3 1. Choose TOP sketch plane 2. Click Sketch tool Figure 2. Layout of an empty Pro/E part Sketch and Sweep 1. Click the Top Reference plan. This is where you draw a sketch. 2. Click the Sketch tool. All the information should be filled up (Figure 3) 3. Click Sketch button in Figure Now Pro/E is in the Sketch mode. This will allow you to sketch in the XZ plane 5. Close the References window by click close button (Figure 4). Chuanyu tony Feng 3

4 Figure 3. Start a sketch: Options FYI: Insert and Sketch are the most useful tools. Some of them have a speed button in the Toolbar region. Figure 4. Start a sketch Chuanyu tony Feng 4

5 6. You can setup Grid and Snap options by Click menu Sketch Options, check Grid and Snap to Grid options. Click the Green Check button: (Figure 5) 7. Choose the Line Tool on the right toolbar to make a sketch. To choose the Line tools, you can directly click the Line Tool in the Sketcher Tools region, or click menu Sketch Line Line. Figure 5. Sketcher Preferences and Menu Manager Chuanyu tony Feng 5

6 1. Use the Line Tool to draw two lines as following 2. Use fillet tools to draw the tangent arc Click the lines near here to create a circular fillet Figure 6. Draw the sketch 8. Draw two lines as shown in Figure 6 using Line Tool. 9. Change dimension; make it 10 and 3 as shown. (you can also change it later after you make the fillet). 10. Click Fit tool to redraw the sketch. 11. Click the Fillet tool to choose the fillet tool 12. Click on the two lines ( move the mouse near the corner of these two lines) 13. Double click the fillet dimension, and change it to 1. ( Figure 7 is the final sketch) Chuanyu tony Feng 6

7 Double click the fillet radius dimension to change it to 1 This will be the final looking of the trajectory sketch used to generate an L- Shaped Rod Figure 7. Final Sketch 14. If you want to change the dimension, double click on the dimension itself, then type in a new dimension. 15. Click Checkmark to finish the sketch. 16. Rotate the sketch by moving the mouse around while Holding middle mouse button down. 17. Now you have a sketch in the 3D space (Figure 8). Chuanyu tony Feng 7

8 Figure 8. 3D view of the Sketch 18. Click main menu: Insert Sweep Protrusion, Figure 9. Sweep Feature Chuanyu tony Feng 8

9 19. Choose Select Traj from the Menu Manager Figure 10. Select Trajectory 20. Holding Ctrl key and Click / select the segment of the sketch one by one. When finished, click Middle mouse button or click OK in the select window. Select one by one while holding Ctrl Key Figure 11, select the segments Chuanyu tony Feng 9

10 21. Click Middle mouse button or Done in the Menu Manager to finish it (Figure 12). Figure 12. click Done 22. Pro/E will move to next step automatically as shown in Figure 13. Figure 13. Ask for Section Chuanyu tony Feng 10

11 23. Move away the Protrusion sweep window so you can see the sketcher tools. 24. Select Circle tool and draw as shown in Figure 14, change diameter to Finish the sketch by click. 1. Select circle tool 2. Draw the section 4. Click OK 3. Finish the sketch Figure 14. Draw the section 26. Click OK in the Protrusion sweep window to generate the SWEEP feature. Figure 15. Final L-Shaped Rod Chuanyu tony Feng 11

12 27. Click Fit tool on the tool bar to redraw the L-shaped rod. 28. Save the part by click File Save, or click the disk icon in the tool bar. FEA using Pro/MECHANICA Similar to Tutorial 2, you will use integrated Pro/MECHANICA to analyze the L-Shaped Rod. It also consists of 3 steps: 1. Assign material information 2. Setup load and constraint boundary conditions 3. Run the analysis and view the results Change working mode to Pro/MECHANICA 1. Click menu Applications Mechanica to Enter Pro/MECHANICA working mode. 2. Review the unit information, Click Continue button to proceed (Figure 16) Figure 16. Unit information Chuanyu tony Feng 12

13 3. In pop-up dialog Model Type, select Structure if it is not there (Figure 17). 4. Make sure FEM Mode is UN-checked. This option tells Pro/MECHANICA to use its own FEA solver. If you check the FEM Mode, it will generate FEA input file for external solvers, such as ANSYS. 5. Click OK to proceed. Figure 17. Choose the working model type Create a new material and assign it to the part 1. Show the Mechanica Objects and Actions tool bar on the right chest region. 1. Put mouse in the right toolchest region, 2. Right click the show up the Configuration menu 3. Make sure Mechanica Objects and Actions are checked. This information is also accessible from Main Menu: Inserts and Analysis Figure 18. Right toolchest configuration Chuanyu tony Feng 13

14 2. Select Main menu: Properties Materials 3. Select Al6061 from the Material in Library List. 4. Click add it to the Material in Model List. 2. Click it 3. Click Assign Part 1. Select Al 6061 Figure 19. Materials 5. Click Assign button, Select Part from the list menu. Pro/E will hide the materials dialog and let you choose the part for the material. 6. Move mouse over the Rod, it will become highlighted. Click on it. 7. Click middle mouse button to confirm the selection. Or Click the OK button in the Select window. 8. close the materials window 9. Save the file Chuanyu tony Feng 14

15 Apply Boundary Conditions: Constraints and Loads Boundary conditions including loads and constraints are applied in this section. You can use the shortcut on the toolbar or use corresponding menu. Displacement boundary 1. Click empty area in the graphic area to deselect anything. 2. Click or main menu: Insert Displacement Constraint, You will see something like Figure Select one end of the rod ( Long arm end) 4. Click mouse middle button to confirm the selection ( or click OK button in the select window). Then the two small windows at the bottom will close. These 3 new windows will pop up for inputting corresponding information Notice this! Click this end to select. Click middle mouse button or OK button Figure 20 Apply constraints Chuanyu tony Feng 15

16 5. Input Fixed_End as the name of the constraint, and then click OK button to finis the setup. Input a new name It shows surface selected. Figure 21. Setup constraint Chuanyu tony Feng 16

17 Apply Load 6. Rotate the Rod, let the end of the short arm facing you. This time you will use a new method to apply load. 7. Let s select the surface as shown in Figure 22 first. 8. Then click the or main menu: Insert Force/Moment Load. 9. Notice that in the Force/Moment Load window, reference has been selected already. 10. Change the name to Applied_Load, 11. Input the load as shown in Figure 22, x= -75, y = -80, z = Click Ok to confirm it. 13. Now the Boundary conditions are all setup. We are ready to do the analysis. 2. Click Force/Moment Load 1. Select this surface first 3. Selection is finished already Figure 22. Apply Load Chuanyu tony Feng 17

18 You can review and edit load and displacement boundary conditions from Model Tree Figure 23. Rod with Load and displacement boundary condition applied Chuanyu tony Feng 18

19 14. Click main menu: Analysis Mechanical Analysis/Studies 15. It will bring the Analysis and Design Studies window (Figure 24) 16. Click menu File New Static from Analysis and Design studies window Figure It will bring the Static Analysis Definition window (Figure 25) 18. Make sure Constrains and Loads set are highlighted. 19. Click OK to proceed Figure 25 Chuanyu tony Feng 19

20 20. Click menu: Run Start in the Analysis and Design Studies window(figure 26) 21. Click Yes on the Question window for error detection. 22. Click the Display study status button to see the status of analysis Showing results later Display study status Figure 26. Run analysis Chuanyu tony Feng 20

21 Figure 27. Run status 23. Analysis will be done once you see the Run Completed. Close the window when it is done. 24. click the main menu: Analysis Results ( button ), Pro/E will start a new window. Click menu: Insert Results Window, you will see a new window popped up, Result Window Definition. 25. If you click the button directly in the window show in Figure 26, it will automatically pop up Result Window Definition with opened result (Figure 30). So you can go to Step 29 directly. Figure 28 Chuanyu tony Feng 21

22 26. Click the button 27. chose Analysis1, click Open Figure 29. Open the result file 28. Result Window Definition is extended, more options are shown. 29. Choose xx component in Quantity page(figure 30) Figure 30. Setup options Chuanyu tony Feng 22

23 30. Select Display Options page, setup as shown in the following figure. Make sure Deformed option is un-checked. 31. Click OK and Show to display the stress distribution 32. You can turn off the shade option by click: View Shade ( un-check it) Figure 31. Setup options Chuanyu tony Feng 23

24 33. You can edit the Result window options anytime by select menu: Edit Result Window (or click ) to edit the result window. Figure 32. Results Figure 33. Cutting / Capping Surfs Chuanyu tony Feng 24

25 34. In the Result Surface Definition window, change the type to Capping Surface, select YZ plane, and the Below location. Uncheck the % box and type in a depth of 8 inches from the origin (elbow of the rod) as shown below. The Click Apply button to see the effect. Figure 34 Chuanyu tony Feng 25

26 35. Click the Left view from the Save view list, you can then zoom in to check the detailed stress distribution. 36. Use the technique in Tutorial 02 to save the result as an image file. 37. Alternative method to save results as an image file: Press key: Alt + Print Screen to copy the full result window into clip board, then use windows program Paint or any other program to save it into a JPEG file. For Paint program, Click Start Programs Accessories Paint. Use Ctrl + V to paste it. Save it as jpeg file. All pictures in these tutorials were obtained through this method. Figure 35 Chuanyu tony Feng 26