INFORMATION SYSTEMS SERVICE NETWORKS AND TELECOMMUNICATIONS SECTOR. VPN Remote Access Installation and Configuration Guide Operating System: MAC OS X

Transcription

1 INFORMATION SYSTEMS SERVICE NETWORKS AND TELECOMMUNICATIONS SECTOR VPN Remote Access Installation and Configuration Guide Operating System: MAC OS X ΥΠΣ ΕΔ/49 August 12 th, 2011

2 A. Installation of the Client Software B. Configuration of the Client Software C. Enabling VPN service using the computer s native support * for MAC OS 10.6 (Snow Leopard) or newer software releases 2

3 A. INSTALLATION OF THE CLIENT SOFTWARE Important note: If your software release is MAC OS 10.6 (Snow Leopard) or MAC OS 10.7 (Lion), you MUST enable the native VPN without installing the Cisco VPN client. Please follow the instructions in section Enabling VPN service using the computer s native support For previous MAC software releases, please follow the steps as indicated below: Step A1: Open your browser and type in the following url You will then be asked to provide logon information username and password. These are the same credentials as those you use to access your University of Cyprus webmail. Step A2: A list containing four different clients in.zip format will appear. Click on the one that reads Download Cisco IPSec client for Mac. Download it, save it on your computer and extract it to a folder that suits you. Step A3: After extracting the contents of the.zip folder you downloaded, the following icon shall appear on your desktop. Double click on the icon to begin the installation process: 3

4 Step A4: On the following screen that will appear, double click on the paper box: Step A5: On the following screen click Continue: 4

5 Step A6: If you are unsure about the version of your Operating System, click on the apple icon in the title bar and then select About this Mac. If your version is 10.4 or greater click Continue to proceed with the installation. Please note that if you have a version earlier than 10.4, VPN client will not be able to run on your computer. Step A7: The Software License Agreement will appear next. Click on the Continue button: 5

6 Step A8: Click on Agree to continue with the installation: Step A9: On the following screen that will appear, click Install: 6

7 Step A10: A screen will appear informing you on the successful completion of the installation. Click Close: You can now proceed to configuring the client software. Instructions on how to configure the client software can be found at: Configuration of the Client Software 7

8 B. CONFIGURATION OF THE CLIENT SOFTWARE Step B1: Go to Applications and double click on the newly installed application VPNClient: Step B2: On the following screen click the Import icon: 8

9 Step B3: Search for the folder where you extracted the VPN Client after the download. Unless you specified a different folder for saving it, it shall be under admin > Downloads > MACVPNCLIENT. Click on the University of Cyprus.pcf file and then click Open: Note that the process of importing the pcf file will be performed only once; there is no need to repeat it each time you wish to connect. Step B4: The following message that will appear informs you on the successful import of the pcf file. Click OK to continue: 9

10 Step B5: Select the UniversityofCyprus entry and then click on the Connect icon: Step B6: You will be prompted to enter your credentials at the following screen. Username and password are the same as the ones you use to access your University of Cyprus account: 10

11 Step B7: The yellow lock that appears before the status indicates that you are now connected to the University of Cyprus network. If you wish to Disconnect, you can click on the Disconnect icon. 11

12 C. ENABLING VPN SERVICE USING THE COMPUTER S NATIVE SUPPORT Step C1: Open the OS X System Preferences (icon shown below): Step C2: Click on the network icon: 12

13 Step C3: Click on the + button, located in the bottom left corner of the Network screen: Step C4: In the new dialogue box that will appear, choose VPN for the Interface field, then Cisco IPSec for the VPN Type field. You may complete the Service Name field with any name that you wish to give to your VPN connection, for example UCY VPN. After you have completed these three fields, click on the Create button: 13

14 Step C5: Complete the Server Address field with ucyvpn.ucy.ac.cy. Enter your username and password in the respective fields (you will be asked to provide your credentials every time you attempt to connect to the VPN service). The username and password are the same as those you use to access your University of Cyprus account. Once you have entered this information, click on the Authentication Settings button: Step C6: Click on the Shared Secret radio button and enter the following key: 4p0m4kr1sm3n1 In the Group name field, enter remotevpn. Click OK and then Apply (The Apply button will be located in the bottom right corner of the underlying window) 14

15 Step C7: After completing the above steps (C1 to C6), a VPN entry will be visible on the left pane of the the Network options as shown below. If you wish to connect to your UCY VPN connection, click on this entry and then click on the Connect button. Step C8: If you tick the option Show VPN status in menu bar, then a VPN icon will appear on the menu bar. Choose Connect to UCY VPN: 15

16 Step C9: You will be prompted to enter your Account Name and Password (these credentials are the same as those you use to connect to your webmail account. Enter your credentials and click OK. Once you have successfully connected to the UCY VPN, the following icon will be displayed on the status bar, indicating that you have an active VPN connection and the time this connection lasts: 16