# Chapter 11 Heat Engines and the. Thermodynamics

Save this PDF as:

Size: px
Start display at page:

## Transcription

1 Chapter 11 Heat Engines and the Second Law of Thermodynamics

2 The laws of thermodynamics...are critical to making intelligent choices about energy in today s global economy.

3 What Is a Heat Engine? How do heat engines work? What determines their efficiency?

4 Heat Engines! A gasoline engine is a form of a heat engine. " Gasoline is mixed with air. " A spark ignites the mixture, which burns rapidly. " Heat is released from the fuel as it burns. " The heat causes the gases in the cylinder to expand, doing work on the piston. " The work done on the piston is transferred to the drive shaft and wheels.

5 Heat Engines " The wheels push against the road. " According to Newton s third law, the road exerts a force on the tires, allowing the car to move forward.! Not all the heat from burning fuel is converted to work done in moving the car. " The exhaust gases emerging from the tailpipe release heat into the environment. " Unused heat is a general feature of heat engines.

6 Heat Engines! All heat engines share these main features of operation: " Thermal energy (heat) is introduced into the engine. " Some of this energy is converted to mechanical work. " Some heat (waste heat) is released into the environment at a temperature lower than the input temperature. Q H = W + Q C

7 Efficiency! Efficiency is the ratio of the net work done by the engine to the amount of heat that must be supplied to accomplish this work. e = W Q H

8 A heat engine takes in 1200 J of heat from the high-temperature heat source in each cycle, and does 400 J of work in each cycle. What is the efficiency of this engine? a) 33% b) 40% c) 66% Q H = 1200 J W = 400 J e = W / Q H = (400 J) / (1200 J) = 1/3 = 0.33 = 33%

9 How much heat is released into the environment in each cycle? a) 33 J b) 400 J c) 800 J d) 1200 J Q C = Q H - W = 1200 J J = 800 J

10 Carnot Engine! The efficiency of a typical automobile engine is less than 30%. " This seems to be wasting a lot of energy. " What is the best efficiency we could achieve? " What factors determine efficiency?! In analogy to water wheels, Carnot reasoned that the greatest efficiency of a heat engine would be obtained by taking all the input heat at a single high temperature and releasing all the unused heat at a single low temperature.

11 Carnot Engine and Carnot Cycle! Carnot also reasoned that the processes should occur without undue turbulence. " The engine is completely reversible: it can be turned around and run the other way at any point in the cycle, because it is always near equilibrium. " This is Carnot s ideal engine.! The cycle devised by Carnot that an ideal engine would have to follow is called a Carnot cycle.! An (ideal, not real) engine following this cycle is called a Carnot engine.

12 1. Heat flows into cylinder at temperature T H. The fluid expands isothermally and does work on the piston. 2. The fluid continues to expand, adiabatically. 3. Work is done by the piston on the fluid, which undergoes an isothermal compression. 4. The fluid returns to its initial condition by an adiabatic compression.

13 Carnot Efficiency! The efficiency of Carnot s ideal engine is called the Carnot efficiency and is given by: e C = T H " T C T H! This is the maximum efficiency possible for any engine taking in heat from a reservoir at absolute temperature T H and releasing heat to a reservoir at temperature T C.! Even Carnot s ideal engine is less than 100% efficient.

14 A steam turbine takes in steam at a temperature of 400 C and releases steam to the condenser at a temperature of 120 C. What is the Carnot efficiency for this engine? a) 30% b) 41.6% c) 58.4% d) 70% T H = 400 C = 673 K T C = 120 C = 393 K e C = (T H - T C ) / T H = (673 K K) / (673 K) = 280 K / 673 K = = 41.6%

15 If the turbine takes in 500 kj of heat in each cycle, what is the maximum amount of work that could be generated by the turbine in each cycle? a) 0.83 J b) kj c) 28 kj d) 208 kj Q H = 500 kj e = W / Q H, so W = e Q H = (0.416)(500 kj) = 208 kj

16 Second Law of Thermodynamics! No engine, working in a continuous cycle, can take heat from a reservoir at a single temperature and convert that heat completely to work.! Therefore, no engine can have a greater efficiency than a Carnot engine operating between the same two temperatures.

17 Second Law of Thermodynamics! An engine with an efficiency greater than the Carnot engine would produce a greater amount of work than the Carnot engine, for the same amount of heat input Q H.! Some of this work could be used to run the Carnot engine in reverse, returning the heat released by the first engine to the higher-temperature reservoir.

18 Second Law of Thermodynamics! The remaining work W excess would be available for external use, and no heat would end up in the lower-temperature reservoir.! The two engines would take a small quantity of heat from the higher-temperature reservoir and convert it completely to work.! This would violate the second law of thermodynamics.

19 Refrigerators, Heat Pumps, and Entropy! If a heat engine is run in reverse, then work W is done on the engine as heat Q C is removed from the lowertemperature reservoir and a greater quantity of heat Q H is released to the highertemperature reservoir.! A device that moves heat from a cooler reservoir to a warmer reservoir by means of work supplied from some external source is called a heat pump.

20 ! The first law of thermodynamics requires that, for a complete cycle, the heat released at the higher temperature must equal the energy put into the engine in the form of both heat and work.! The engine returns to its initial condition at the end of each cycle; the internal energy of the engine does not change.! More heat is released at the higher temperature than was taken in at the lower temperature. W + Q C = Q H

21 A heat pump uses 200 J of work to remove 300 J of heat from the lower-temperature reservoir. How much heat would be delivered to the higher-temperature reservoir? a) 100 J b) 200 J c) 300 J d) 500 J W = 200 J Q C = 300 J Q H = W + Q C = 200 J J = 500 J

22 Refrigerators and Heat Pumps! A refrigerator is also a form of a heat pump.! It also moves heat from a cooler reservoir to a warmer reservoir by means of work supplied from some external source.! It keeps food cold by pumping heat out of the cooler interior of the refrigerator into the warmer room.! An electric motor or gas-powered engine does the necessary work.

23 A television commercial shows a couple in the middle of a heat wave, discussing buying an air conditioner. The women is standing in front of the open door of the refrigerator, in an obvious attempt to cool off. #Is this a good idea or a bad idea, as far as their electric bill is concerned? #Will this at least achieve the women s desired result (keeping cool) regardless of how much it costs? #Short of buying an air conditioner, what could they do with the refrigerator to reduce the heat in the kitchen?

24 ! While a refrigerator is a form of heat pump, the term heat pump usually refers to a device that heats a building by pumping heat from the colder outdoors to the warmer interior.! An electric motor does the work needed to run the pump.! The amount of heat available to heat the house is greater than the work supplied: W + Q C = Q H! We can get a larger amount of heat from the heat pump than by converting the electrical energy directly to heat (often 2-3 times as much).

25 ! A heat pump heats a house by exchanging heat in an outside coil and transferring that heat to another coil inside, which releases heat to the air inside the building.! Many heat pumps are designed to pump heat in either direction, acting as air conditioners in the summer.! Most air conditioners are heat pumps that pump heat from inside a building to the warmer exterior.! Heat pumps are most effective for heating houses in climates where the temperature difference is not too great.

26 A television show tested the effectiveness of a product claiming to be the world s smallest air conditioner. It was actually a small hand-held battery-powered fan, and the test was done by a person in a closed glass-walled phone booth. #Is this battery-powered fan operating as a heat pump? #If the person has a normal body temperature, and the sun is shining, would you expect the phone booth s temperature to increase or decrease during the test? #If there was nobody inside the booth and the sun was not shining (no heat going into or out of the phone booth) would you expect the temperature to increase or decrease during the test?

27 Another Statement of The Second Law of Thermodynamics! Heat has a natural tendency to flow from hotter objects to colder objects. This can be expressed in a second statement of the second law of thermodynamics:! Heat will not flow from a colder body to a hotter body unless some other process is also involved.! For example, work can be used to pump heat against its usual direction of flow.

28 ! If heat could flow from the colder to the hotter reservoir without any work, heat released by the heat engine on the right side of the diagram could flow back to the hotter reservoir.! Some heat could then be removed from the hotter reservoir and converted completely to work, without adding heat to the colder reservoir.! This would violate the second law of thermodynamics.

29 Entropy! Heat can be removed from a high-temperature source either by spontaneous flow to a low-temperature reservoir or by being used to run a heat engine.! If the engine is a Carnot engine, the process is completely reversible and the maximum possible work has been obtained from the available heat.

30 ! If the heat simply flows from hot to cold spontaneously, the process is irreversible and the energy is not converted to useful work.! In the irreversible process, we lose some ability to do useful work.! Entropy is the quantity that describes the extent of this loss. " Entropy is sometimes defined as a measure of the disorder of the system. " The entropy of a system increases any time the disorder or randomness of the system increases.

31 A Third Statement of The Second Law of Thermodynamics! Entropy remains constant in reversible processes but increases in irreversible processes.! The entropy of a system decreases only if it interacts with some other system whose entropy is increased in the process. " This happens, for example, in the growth and development of biological organisms.! The entropy of the universe or of an isolated system can only increase or remain constant. Its entropy can never decrease.

32 ! The thermal energy of a gas consists of the kinetic energy of the molecules.! The velocities of these molecules are randomly directed. Only some of them move in the proper direction to push the piston to produce work.! The basic disorganization of heat energy is responsible for the limitations encompassed by the three statements of the second law.! The natural tendency of entropy to increase can only be countered by introducing energy into the system: " For example, solar energy to support biological processes on earth. " For example, work done to organize a room s clutter.

33 Thermal Power Plants and Energy Resources! The most common way of producing electric power in this country is a thermal power plant that uses some form of heat engine, whether fueled by coal, oil, or natural gas (fossil fuels).! Thermodynamics plays an extremely important role in any discussion of the use of energy.! As worldwide economic development continues and fossil-fuel resources are depleted, questions of the optimal uses of energy resources become critical.! Wise decisions depend on the participation of an informed, scientifically literate citizenry.

34 Thermal-Electric Power Plant 1. Fossil fuel (coal, oil, natural gas) is burned to release heat that causes the temperature of water and steam to increase.

35 Thermal-Electric Power Plant 2. Hot steam is run through a turbine (a heat engine) that turns a shaft connected to an electric generator.

36 Thermal-Electric Power Plant 3. Electricity is transmitted through power lines to consumers.

37 ! Because the steam turbine is a heat engine, its efficiency is inherently limited by the second law of thermodynamics. " Any real engine involves some irreversible processes and so must fall short of the ideal conditions of a completely reversible Carnot engine. " A steam turbine comes closer to the ideal than the highly turbulent internal-combustion engine.! The maximum possible efficiency is dictated by the temperature difference between the hot and cold reservoirs. " Heating the steam to as high a temperature as possible is advantageous. " The exhaust temperature will be near the boiling point of water, where the steam condenses to water.

38 ! In practice, only about half the thermal energy released in burning coal or oil is converted to mechanical work or electrical energy.! The rest must be released into the environment at temperatures too low for running heat engines.! Cooling towers transfer this waste heat into the atmosphere, or heated water is released into a river.

39 Alternatives to Fossil Fuels! Nuclear power plants " Lower thermal efficiencies " More heat released into environment " No carbon dioxide and other greenhouse gases released " Nuclear waste must be processed and disposed of

40 ! Geothermal Energy " Heat from the interior of the earth, such as hot springs and geysers. " Water temperature not hot enough to yield a high efficiency Geysers Power Plant in California

41 ! Sun as energy source " Warm ocean currents " Solar power Mirrors focus sunlight to heat a central boiler at a solarthermal power plant

42 High-Grade and Low-Grade Heat " The temperature difference between the hot reservoir and the cold reservoir determine the maximum possible efficiency. " High-grade heat is heat at temperatures around 500 C or higher, and is more useful than heat at lower temperatures. " Low-grade heat, around 100 C or lower, can produce work but with considerably lower efficiency. " Low-grade heat is better used for purposes like heating homes or buildings/ " Much low-grade heat, such as the low-temperature heat released from power plants, goes to waste because it is not economical to transport it to where it might be utilized. " The main advantage of electrical energy is that it is easily transported. " It can be converted to mechanical energy by efficient electric motors. " It can also be converted back to heat, but this is a very inefficient use of high-grade heat (in the initial production of the electrical energy).

43 Perpetual Motion and \$A perpetual-motion machine of the first kind is a proposed engine of machine that would violate the first law of thermodynamics. \$It puts out more energy as work or heat than it takes in. \$Buyer beware: #Where is the energy coming from? #How can the machine put more energy out than went in? Energy Fluids

44 \$A perpetual-motion machine of the second kind does not put more energy out than goes in. \$Instead, it may claim to be able to take heat from a reservoir at a single temperature and convert it completely to work. \$This violates the second law of thermodynamics: some heat must be released into a lowertemperature reservoir. \$Or, it may simply claim a higher efficiency than the Carnot efficiency (for the available temperature difference). \$Such claims may be put forward by well-intentioned but misguided persons. \$Some are promoted by charlatans.

45 Would it be possible to generate electricity by running a water wheel with water drained from the bottom of a pond returning to the top of the pond?

46 Is it possible for a heat engine to operate as shown in the following diagram? a) Yes b) No, not ever c) Only if it is a Carnot engine d) It depends This is a perpetual-motion machine of the second kind. According to the second law of thermodynamics, heat can never be completely converted to work without some waste heat released.

47 Is it possible for a heat engine to operate as shown in the following diagram? a) Yes b) No, not ever c) Only if it is a Carnot engine d) It depends This is a perpetual-motion machine of the first kind. According to the first law of thermodynamics, you can never get out more energy in work than you put in as heat.

48 Is it possible for a heat engine to operate as shown in the following diagram? a) Yes b) No, not ever c) Only if it is a Carnot engine d) It depends This extracts heat from a single source, performs work and puts the remaining heat energy back in the original source of heat. The net effect is to extract heat from a single source and convert it all to work, which is a violation of Kelvin's statement of the second law.

49 Is it possible for a heat pump to operate as shown in the following diagram? a) Yes b) No, not ever c) Only if it is a Carnot engine d) It depends Work must be performed in order to remove heat from the cool reservoir and move it to the hot reservoir.

50 Is it possible for a heat pump to operate as shown in the following diagram? a) Yes b) No, not ever c) Only if it is a Carnot engine d) It depends This violates the first law of thermodynamics. Work is being done to transfer heat from the cooler reservoir to the hotter reservoir. However, more heat is being withdrawn and more work is being done than is being transferred.

51 Is it possible for a heat pump to operate as shown in the following diagram? a) Yes b) No, not ever c) Only if it is a Carnot engine d) It depends This diagram is correct!!! More heat is transferred to the hot reservoir than is taken in from the cold one, with work being done.

### The Second Law of Thermodynamics

Objectives MAE 320 - Chapter 6 The Second Law of Thermodynamics The content and the pictures are from the text book: Çengel, Y. A. and Boles, M. A., Thermodynamics: An Engineering Approach, McGraw-Hill,

### Reversible & Irreversible Processes

Reversible & Irreversible Processes Example of a Reversible Process: Cylinder must be pulled or pushed slowly enough (quasistatically) that the system remains in thermal equilibrium (isothermal). Change

### The Second Law of Thermodynamics

The Second aw of Thermodynamics The second law of thermodynamics asserts that processes occur in a certain direction and that the energy has quality as well as quantity. The first law places no restriction

### Chapter 5 The Second Law of Thermodynamics

Chapter 5 he Second aw of hermodynamics he second law of thermodynamics states that processes occur in a certain direction, not in just any direction. Physical processes in nature can proceed toward equilibrium

### Chapter 4 EFFICIENCY OF ENERGY CONVERSION

Chapter 4 EFFICIENCY OF ENERGY CONVERSION The National Energy Strategy reflects a National commitment to greater efficiency in every element of energy production and use. Greater energy efficiency can

### Lecture 36 (Walker 18.8,18.5-6,)

Lecture 36 (Walker 18.8,18.5-6,) Entropy 2 nd Law of Thermodynamics Dec. 11, 2009 Help Session: Today, 3:10-4:00, TH230 Review Session: Monday, 3:10-4:00, TH230 Solutions to practice Lecture 36 final on

### ENTROPY AND THE SECOND LAW OF THERMODYNAMICS

Chapter 20: ENTROPY AND THE SECOND LAW OF THERMODYNAMICS 1. In a reversible process the system: A. is always close to equilibrium states B. is close to equilibrium states only at the beginning and end

### Chapter 22. Heat Engines, Entropy, and the Second Law of Thermodynamics

Chapter 22 Heat Engines, Entropy, and the Second Law of Thermodynamics C HAP T E R O UTLI N E 221 Heat Engines and the Second Law of Thermodynamics 222 Heat Pumps and Refrigerators 223 Reversible and Irreversible

### Physics 2326 - Assignment No: 3 Chapter 22 Heat Engines, Entropy and Second Law of Thermodynamics

Serway/Jewett: PSE 8e Problems Set Ch. 22-1 Physics 2326 - Assignment No: 3 Chapter 22 Heat Engines, Entropy and Second Law of Thermodynamics Objective Questions 1. A steam turbine operates at a boiler

### Entropy and the Second Law of Thermodynamics. The Adiabatic Expansion of Gases

Lecture 7 Entropy and the Second Law of Thermodynamics 15/08/07 The Adiabatic Expansion of Gases In an adiabatic process no heat is transferred, Q=0 = C P / C V is assumed to be constant during this process

### Laws of Thermodynamics

Laws of Thermodynamics Thermodynamics Thermodynamics is the study of the effects of work, heat, and energy on a system Thermodynamics is only concerned with macroscopic (large-scale) changes and observations

### Chapter 15: Thermodynamics

Chapter 15: Thermodynamics The First Law of Thermodynamics Thermodynamic Processes (isobaric, isochoric, isothermal, adiabatic) Reversible and Irreversible Processes Heat Engines Refrigerators and Heat

### Esystem = 0 = Ein Eout

AGENDA: I. Introduction to Thermodynamics II. First Law Efficiency III. Second Law Efficiency IV. Property Diagrams and Power Cycles V. Additional Material, Terms, and Variables VI. Practice Problems I.

### FUNDAMENTALS OF ENGINEERING THERMODYNAMICS

FUNDAMENTALS OF ENGINEERING THERMODYNAMICS System: Quantity of matter (constant mass) or region in space (constant volume) chosen for study. Closed system: Can exchange energy but not mass; mass is constant

### The First Law of Thermodynamics

Thermodynamics The First Law of Thermodynamics Thermodynamic Processes (isobaric, isochoric, isothermal, adiabatic) Reversible and Irreversible Processes Heat Engines Refrigerators and Heat Pumps The Carnot

### Esystem = 0 = Ein Eout

AGENDA: I. Introduction to Thermodynamics II. First Law Efficiency III. Second Law Efficiency IV. Property Diagrams and Power Cycles V. Additional Material, Terms, and Variables VI. Practice Problems I.

### 6 18 A steam power plant receives heat from a furnace at a rate of 280 GJ/h. Heat losses to the surrounding air from the steam as it passes through

Thermo 1 (MEP 261) Thermodynamics An Engineering Approach Yunus A. Cengel & Michael A. Boles 7 th Edition, McGraw-Hill Companies, ISBN-978-0-07-352932-5, 2008 Sheet 6:Chapter 6 6 17 A 600-MW steam power

### There is no general classification of thermodynamic cycle. The following types will be discussed as those are included in the course curriculum

THERMODYNAMIC CYCLES There is no general classification of thermodynamic cycle. The following types will be discussed as those are included in the course curriculum 1. Gas power cycles a) Carnot cycle

### Module 2.2. Heat transfer mechanisms

Module 2.2 Heat transfer mechanisms Learning Outcomes On successful completion of this module learners will be able to - Describe the 1 st and 2 nd laws of thermodynamics. - Describe heat transfer mechanisms.

### Student Worksheets Energy for a Cleaner Environment

Student Worksheets Energy for a Cleaner Environment Stage 4 Science FW4S1 Name: Introduction Renewable Versus Non-renewable Energy The Sun is a Primary Source of Energy Almost all the energy needed to

### Student Worksheets. Stage 4 Geography FW4G1. Name: FutureWorld 2015 FW4G1

Student Worksheets Stage 4 Geography FW4G1 Name: Introduction Renewable Versus Non-renewable Energy The Sun is a Primary Source of Energy Almost all the energy needed to keep life on Earth going comes

### Applied Thermodynamics for Marine Systems Prof. P. K. Das Department of Mechanical Engineering Indian Institute of Technology, Kharagpur

Applied Thermodynamics for Marine Systems Prof. P. K. Das Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Lecture - 1 Introduction & Some Definitions Good afternoon everybody.

### THERMAL TO MECHANICAL ENERGY CONVERSION: ENGINES AND REQUIREMENTS

THERMAL TO MECHANICAL ENERGY CONVERSION: ENGINES AND REQUIREMENTS Oleg N. Favorsky Russian Academy of Science, Division of Physical-Technical Problems of Energetics, Moscow, Russia Keywords: Power, heat,

### How does solar air conditioning work?

How does solar air conditioning work? In a conventional air conditioning system; The working fluid arrives at the compressor as a cool, low-pressure gas. The compressor is powered by electricity to squeeze

### EE 206 Electric Energy Engineering

Chapter 1: Review Lecturer: Dr Ibrahim Rida Electrical Engineering Department University of Hail First Semester (112) 2011/12 1.2. ENERGY SOURCES Energy resources are the various materials that contain

### Stirling heat engine Internal combustion engine (Otto cycle) Diesel engine Steam engine (Rankine cycle) Kitchen Refrigerator

Lecture. Real eat Engines and refrigerators (Ch. ) Stirling heat engine Internal combustion engine (Otto cycle) Diesel engine Steam engine (Rankine cycle) Kitchen Refrigerator Carnot Cycle - is not very

### Sustainable Living Student Worksheets

Sustainable Living Student Worksheets Stage 4 Design & Technology FW4DT1 Name: Introduction Renewable Versus Non-renewable Energy The Sun is a Primary Source of Energy Almost all the energy needed to keep

### Name: Class: Date: 10. Some substances, when exposed to visible light, absorb more energy as heat than other substances absorb.

Name: Class: Date: ID: A PS Chapter 13 Review Modified True/False Indicate whether the statement is true or false. If false, change the identified word or phrase to make the statement true. 1. In all cooling

### 12.5: Generating Current Electricity pg. 518

12.5: Generating Current Electricity pg. 518 Key Concepts: 1. Electrical energy is produced by energy transformations. 2. Electrical energy is produced from renewable and non-renewable resources. 4. Electrical

### 20 m neon m propane 20

Problems with solutions:. A -m 3 tank is filled with a gas at room temperature 0 C and pressure 00 Kpa. How much mass is there if the gas is a) Air b) Neon, or c) Propane? Given: T73K; P00KPa; M air 9;

### The Basic Physics of Heat Pumps

The Basic Physics of Heat Pumps Hilliard Kent Macomber Emeritus Professor of Physics University of Northern Iowa June 2002 Introduction In order to understand the basic physics of heat pumps, it is necessary

### ME 201 Thermodynamics

ME 0 Thermodynamics Second Law Practice Problems. Ideally, which fluid can do more work: air at 600 psia and 600 F or steam at 600 psia and 600 F The maximum work a substance can do is given by its availablity.

### Chapter 17: Change of Phase

Chapter 17: Change of Phase Conceptual Physics, 10e (Hewitt) 3) Evaporation is a cooling process and condensation is A) a warming process. B) a cooling process also. C) neither a warming nor cooling process.

### Chapter 18 Temperature, Heat, and the First Law of Thermodynamics. Problems: 8, 11, 13, 17, 21, 27, 29, 37, 39, 41, 47, 51, 57

Chapter 18 Temperature, Heat, and the First Law of Thermodynamics Problems: 8, 11, 13, 17, 21, 27, 29, 37, 39, 41, 47, 51, 57 Thermodynamics study and application of thermal energy temperature quantity

### Chapter 10 Temperature and Heat

Chapter 10 Temperature and Heat What are temperature and heat? Are they the same? What causes heat? What Is Temperature? How do we measure temperature? What are we actually measuring? Temperature and Its

### Manure The input to the system, this is produced as waste once animals have consumed plant products.

Resources for Energy System Diagram Activity Labels for Anaerobic digestion poster cut apart and distribute to students Manure The input to the system, this is produced as waste once animals have consumed

### GEOTHERMAL POWER GENERATION A PRIMER ON LOW-TEMPERATURE, SMALL-SCALE APPLICATIONS

GEOTHERMAL POWER GENERATION A PRIMER ON LOW-TEMPERATURE, SMALL-SCALE APPLICATIONS by Kevin Rafferty Geo-Heat Center January 2000 REALITY CHECK Owners of low-temperature geothermal resources are often interested

### Sustainable Design Student Worksheets Stage 4/5 Design & Technology FW45DT2. Name: FutureWorld 2015 FW45DT2

Sustainable Design Student Worksheets Stage 4/5 Design & Technology FW45DT2 Name: Introduction Renewable Versus Non-renewable Energy The Sun is a Primary Source of Energy Almost all the energy needed to

### T E A C H E R S N O T E S

T E A C H E R S N O T E S Focus: Students explore energy: its sources, forms, and transformations. Students also consider the benefits of energy-efficient technologies and energy conservation. Learning

### Energy Transformations

Energy Transformations Concept Sheet Energy Transformations PS.6: The student will investigate and understand states and forms of energy and how energy is transferred and transformed. 1. Energy is the

### CHAPTER 7 THE SECOND LAW OF THERMODYNAMICS. Blank

CHAPTER 7 THE SECOND LAW OF THERMODYNAMICS Blank SONNTAG/BORGNAKKE STUDY PROBLEM 7-1 7.1 A car engine and its fuel consumption A car engine produces 136 hp on the output shaft with a thermal efficiency

### TEACHER BACKGROUND INFORMATION THERMAL ENERGY

TEACHER BACKGROUND INFORMATION THERMAL ENERGY In general, when an object performs work on another object, it does not transfer all of its energy to that object. Some of the energy is lost as heat due to

### Supplementary Notes on Entropy and the Second Law of Thermodynamics

ME 4- hermodynamics I Supplementary Notes on Entropy and the Second aw of hermodynamics Reversible Process A reversible process is one which, having taken place, can be reversed without leaving a change

### Measuring Temperature

Measuring Temperature The standard metric unit of temperature is the degree Celsius ( C). Water freezes at 0 C. Water boils at 100 C. The Fahrenheit scale is used only in the United States. Why Do We Need

### In the compression-refrigeration loop (air conditioning), which is likely to be warmer? 1. Condenser coil 2. Evaporator coil

In the compression-refrigeration loop (air conditioning), which is likely to be warmer? 1. Condenser coil 2. Evaporator coil Answer: (1) Condenser coil See the video. A.R.E. Building Systems Study Guide

### c. Applying the first law of thermodynamics from Equation 15.1, we find that c h c h.

Week 11 homework IMPORTANT NOTE ABOUT WEBASSIGN: In the WebAssign versions of these problems, various details have been changed, so that the answers will come out differently. The method to find the solution

### Question 1. Passage (click here to show all) Question 2. Use the diagram and information below to answer question #.

Question 1 Use the diagram and information below to answer question #. A teacher places a ribbon of magnesium on a wire and suspends it in a flask. She then seals the flask and runs electricity through

### Forms of Energy: Multiple Transformations : Teacher Notes

Forms of Energy: Multiple Transformations : Teacher Notes Introduction The focus of the investigation is to further define energy and realize that chains of energy transformations can occur. The VoltageCurrent,

### Physics 5D - Nov 18, 2013

Physics 5D - Nov 18, 2013 30 Midterm Scores B } Number of Scores 25 20 15 10 5 F D C } A- A A + 0 0-59.9 60-64.9 65-69.9 70-74.9 75-79.9 80-84.9 Percent Range (%) The two problems with the fewest correct

### Station #1 Interpreting Infographs

Energy Resources Stations Activity Page # 1 Station #1 Interpreting Infographs 1. Identify and explain each of the energy sources (5) illustrated in the infograph. 2. What do the white and black circles

### 15 THERMODYNAMICS. Learning Objectives

CHAPTER 15 THERMODYNAMICS 505 15 THERMODYNAMICS Figure 15.1 A steam engine uses heat transfer to do work. Tourists regularly ride this narrow-gauge steam engine train near the San Juan Skyway in Durango,

### Energy and Society. Professor Ani Aprahamian

Energy and Society Professor Ani Aprahamian Wednesday, September 14th Nieuwland Science Hall 123; 6 pm - 7pm Dr. Peter Burns - "Nuclear Energy: Past Mistakes, Current Challenges, Future Prospects" Thursday,

### Sixth Grade Energy, Heat, and Energy Transfer Assessment

Sixth Grade Energy, Heat, and Energy Transfer Assessment 1a. Which of the following is not one of the six forms of energy? Circle the answer. electrical chemical petroleum wave (light, sound) mechanical

### UNIT 5 REFRIGERATION SYSTEMS

UNIT REFRIGERATION SYSTEMS Refrigeration Systems Structure. Introduction Objectives. Vapour Compression Systems. Carnot Vapour Compression Systems. Limitations of Carnot Vapour Compression Systems with

### Temperature. Temperature

Chapter 8 Temperature Temperature a number that corresponds to the warmth or coldness of an object measured by a thermometer is a per-particle property no upper limit definite limit on lower end Temperature

### Generating Current Electricity: Complete the following summary table for each way that electrical energy is generated. Pros:

P a g e 1 Generating Current Electricity: Complete the following summary table for each way that electrical energy is generated. Generating Electrical Energy Using Moving Water: Hydro-Electric Generation

### Energy and Energy Transformations Test Review

Energy and Energy Transformations Test Review Completion: 1. Mass 13. Kinetic 2. Four 14. thermal 3. Kinetic 15. Thermal energy (heat) 4. Electromagnetic/Radiant 16. Thermal energy (heat) 5. Thermal 17.

### Basics. Energy from the sun, via photosynthesis in plants

Biomass Basics Energy from the sun, via photosynthesis in plants This is the same energy we use as food This is the same energy that made fossil fuels; fossil fuels are concentrated over time by the heat

### KS3 Renewable Energy. EcoStyle.co.uk. Introductory Presentation

Introductory Presentation Energy Energy is a vital to our way of life. Here are a some examples of where energy is used: Homes: central heating, powering electrical appliances, and heating water Public

### Conventional Energy Sources

9.2 Conventional Energy Sources Key Question: What benefits and problems come with common sources of energy? Hints The word plant here is not the kind that grows out of the ground. In this section, plants

### In a cyclic transformation, where the final state of a system is the same as the initial one, U = 0

Chapter 4 Entropy and second law of thermodynamics 4.1 Carnot cycle In a cyclic transformation, where the final state of a system is the same as the initial one, U = 0 since the internal energy U is a

### THE SECOND LAW OF THERMODYNAMICS

1 THE SECOND LAW OF THERMODYNAMICS The FIRST LAW is a statement of the fact that ENERGY (a useful concept) is conserved. It says nothing about the WAY, or even WHETHER one form of energy can be converted

### ESO201A: Thermodynamics

ESO201A: Thermodynamics Instructor: Sameer Khandekar First Semester: 2015 2016 Lecture #1: Course File Introduction to Thermodynamics, Importance, Definitions Continuum, System: closed, open and isolated,

### ENERGY PRODUCING SYSTEMS

ENERGY PRODUCING SYSTEMS SOLAR POWER INTRODUCTION Energy from the sun falls on our planet on a daily basis. The warmth of the sun creates conditions on earth conducive to life. The weather patterns that

### 10 Nuclear Power Reactors Figure 10.1

10 Nuclear Power Reactors Figure 10.1 89 10.1 What is a Nuclear Power Station? The purpose of a power station is to generate electricity safely reliably and economically. Figure 10.1 is the schematic of

### Science Tutorial TEK 6.9C: Energy Forms & Conversions

Name: Teacher: Pd. Date: Science Tutorial TEK 6.9C: Energy Forms & Conversions TEK 6.9C: Demonstrate energy transformations such as energy in a flashlight battery changes from chemical energy to electrical

### C H A P T E R T W O. Fundamentals of Steam Power

35 C H A P T E R T W O Fundamentals of Steam Power 2.1 Introduction Much of the electricity used in the United States is produced in steam power plants. Despite efforts to develop alternative energy converters,

### OUTCOME 2 INTERNAL COMBUSTION ENGINE PERFORMANCE. TUTORIAL No. 5 PERFORMANCE CHARACTERISTICS

UNIT 61: ENGINEERING THERMODYNAMICS Unit code: D/601/1410 QCF level: 5 Credit value: 15 OUTCOME 2 INTERNAL COMBUSTION ENGINE PERFORMANCE TUTORIAL No. 5 PERFORMANCE CHARACTERISTICS 2 Be able to evaluate

### MCQ - ENERGY and CLIMATE

1 MCQ - ENERGY and CLIMATE 1. The volume of a given mass of water at a temperature of T 1 is V 1. The volume increases to V 2 at temperature T 2. The coefficient of volume expansion of water may be calculated

### CANADA S RESOURCES: CONVENTIONAL AND ALTERNATIVE ENERGY

CANADA S RESOURCES: CONVENTIONAL AND ALTERNATIVE ENERGY Introduction Canadians are among the highest energy consumers in the world. Why? (list 3 possible reasons) Northern climate/very cold temperatures

### Heating the Atmosphere. Dr. Michael J Passow

Heating the Atmosphere Dr. Michael J Passow Heat vs. Temperature Heat refers to energy transferred from one object to another Temperature measures the average kinetic energy in a substance. When heat energy

### AIR CONDITIONING EFFICIENCY F8 Energy eco-efficiency opportunities in Queensland Foundries

AIR CONDITIONING EFFICIENCY F8 Energy eco-efficiency opportunities in Queensland Foundries Hot tips and cool ideas to save energy and money! Air conditioning units or systems are often used by foundries

### Gas Turbine cycles and Propulsion system. Sarika Goel 3 rd year,chemical Engineering, IIT Delhi Guide : Prof. Gautam Biswas & Prof. S.

Gas Turbine cycles and Propulsion system Sarika Goel 3 rd year,chemical Engineering, IIT Delhi Guide : Prof. Gautam Biswas & Prof. S. Sarkar Outline Introduction- Gas turbine cycles Applications of gas

### Unit 2 Energy & States of Matter Part 1 - Objectives

Unit 2 Energy & States of Matter Part 1 - Objectives 1. Relate observations of diffusion to particle motion and collision in the gas and liquid phases. 2. Relate observations regarding the addition of

### Energy & Conservation of Energy. Energy & Radiation, Part I. Monday AM, Explain: Energy. Thomas Birner, ATS, CSU

Monday AM, Explain: Energy MONDAY: energy in and energy out on a global scale Energy & Conservation of Energy Energy & Radiation, Part I Energy concepts: What is energy? Conservation of energy: Can energy

### The final numerical answer given is correct but the math shown does not give that answer.

Note added to Homework set 7: The solution to Problem 16 has an error in it. The specific heat of water is listed as c 1 J/g K but should be c 4.186 J/g K The final numerical answer given is correct but

### The First Law of Thermodynamics

The First Law of Thermodynamics (FL) The First Law of Thermodynamics Explain and manipulate the first law Write the integral and differential forms of the first law Describe the physical meaning of each

### ELECTRIC GENERATING ULTRA EFFICIENT m-chp

ZD-E-14-01 03/2014 Copyright KD Navien All rights reserved. Subject to change without notice SE series Navien Hybrigen SE ELECTRIC GENERATING ULTRA EFFICIENT m-chp KyungDong Navien co., Ltd. (Head Office,

### How Ground/Water Source Heat Pumps Work

How Ground/Water Source s Work Steve Kavanaugh, Professor Emeritus of Mechanical Engineering, University of Alabama Ground Source s (a.k.a. Geothermal s) are becoming more common as the costs of energy

### Thermodynamics. Thermodynamics 1

Thermodynamics 1 Thermodynamics Some Important Topics First Law of Thermodynamics Internal Energy U ( or E) Enthalpy H Second Law of Thermodynamics Entropy S Third law of Thermodynamics Absolute Entropy

### Section 7. Laws of Thermodynamics: Too Hot, Too Cold, Just Right. What Do You See? What Do You Think? Investigate.

Chapter 6 Electricity for Everyone Section 7 Laws of Thermodynamics: Too Hot, Too Cold, Just Right What Do You See? Learning Outcomes In this section, you will Assess experimentally the final temperature

### Problem Set 1 3.20 MIT Professor Gerbrand Ceder Fall 2003

LEVEL 1 PROBLEMS Problem Set 1 3.0 MIT Professor Gerbrand Ceder Fall 003 Problem 1.1 The internal energy per kg for a certain gas is given by U = 0. 17 T + C where U is in kj/kg, T is in Kelvin, and C

### 20 Entropy and the Second Law of Thermodynamics

20 Entropy and the Second Law of Thermodynamics An anonymous graffito on a wall of the Pecan Street Cafe in Austin, Texas, reads: Time is God s way of keeping things from happening all at once. Time also

### Entropy and The Second Law of Thermodynamics

The Second Law of Thermodynamics (SL) Entropy and The Second Law of Thermodynamics Explain and manipulate the second law State and illustrate by example the second law of thermodynamics Write both the

### Work and Energy. Work = Force Distance. Work increases the energy of an object. Energy can be converted back to work.

Work and Energy Ch. 6 Work = Force Distance Work increases the energy of an object. Energy can be converted back to work. Therefore, energy and work have the same unit: Newton meter = Nm Energy per gram,

### Greenhouse Gas Inventory Report

Fairfax County Public Schools Greenhouse Gas Inventory Report For Calendar Year 2013 Fairfax County Public Schools Office of Facilities Management 5025 Sideburn Road Fairfax, Virginia 22032 This report

### ENERGY CONVERSION & ENERGY EFFICIENCY

ENERGY CONVERSION & ENERGY EFFICIENCY Energy is 'used' by being degraded. Mechanical energy >> Friction >> Heat >> Low grade heat Electrical energy >> Mechanical energy >> Low grade heat High grade heat

### Chapter 11. Refrigeration Cycles

Chapter 11 Refrigeration Cycles The vapor compression refrigeration cycle is a common method for transferring heat from a low temperature space to a high temperature space. The figures below show the objectives

### SAMPLE CHAPTERS UNESCO EOLSS

STEAM TURBINE OPERATIONAL ASPECTS R.A. Chaplin Department of Chemical Engineering, University of New Brunswick, Canada Keywords: Steam Turbines, Operation, Supersaturation, Moisture, Back Pressure, Governing

### The Kinetic Theory of Gases Sections Covered in the Text: Chapter 18

The Kinetic Theory of Gases Sections Covered in the Text: Chapter 18 In Note 15 we reviewed macroscopic properties of matter, in particular, temperature and pressure. Here we see how the temperature and

### An introduction to thermodynamics applied to Organic Rankine Cycles

An introduction to thermodynamics applied to Organic Rankine Cycles By : Sylvain Quoilin PhD Student at the University of Liège November 2008 1 Definition of a few thermodynamic variables 1.1 Main thermodynamics

### FIELD TRIP TO A POWER PLANT - A Reading Guide

TITLE: TOPIC: FIELD TRIP TO A POWER PLANT - A Reading Guide Energy and the sources of energy used in power plants GRADE LEVEL: Secondary CONTENT STANDARD: Earth and Space Science CONTENT OBJECTIVE: For

### Section 15.1 Energy and Its Forms (pages 446 452)

Section 15.1 and Its Forms (pages 446 452) This section describes how energy and work are related. It defines kinetic energy and potential energy, and gives examples for calculating these forms of energy.

### Use Energy Efficiently Booklet Practice Energy Efficiency Poster Teacher s Guide

Use Energy Efficiently Booklet Practice Energy Efficiency Poster Teacher s Guide INTRODUCTION The Use Energy Efficiently booklet teaches the basic principles of energy and how to use it efficiently. The

### Understanding and Measuring School Electronics

Understanding and Measuring School Electronics MATERIALS NEEDED: 1. 6 energy monitoring devices (note: these can be obtained from a variety of sources, i.e., local hardware stores, internet [average cost

### Expansion and Compression of a Gas

Physics 6B - Winter 2011 Homework 4 Solutions Expansion and Compression of a Gas In an adiabatic process, there is no heat transferred to or from the system i.e. dq = 0. The first law of thermodynamics

### Proe Power Systems, LLC

Afterburning Cycle for 21st Century Stirling Engine Cycle Comparison Leakage Makeup Gas Supply EXTERNAL HEAT SOURCE (IE SOLAR) COMPRESSOR HEAT REGENERATOR EXPANDER Stirling Engine Diagram Page 1 Engines

### Name Class Date. You do twice as much work. b. You lift two identical books one meter above the ground.

Exercises 9.1 Work (pages 145 146) 1. Circle the letter next to the correct mathematical equation for work. work = force distance work = distance force c. work = force distance d. work = force distance