For Double Strollers. Assembly Instructions

Transcription

1 Assembly Instructions Car seat adaptor For Double Strollers The Double Car Seat Adaptor is designed to be used on your Baby Jogger City Mini or City Mini GT double stroller as well as several other Baby Jogger stroller models. For a complete list of compatible stroller models, please contact Baby Jogger Customer Care. NOTE: Before you start, please refer to the Table of Contents on page 2 to ensure you follow the proper installation instructions for your car seat. This Kit Includes: 1 Adaptor Bracket 1 U-Shaped Bar (A) 1 U-Shaped Bar (B) 1 Spring Support Bar (C) 1 Graco Support Bar (D) U-Shaped Bar (A) U-Shaped Bar (B) Spring Support Bar (C) Graco Support Bar (D) Adjustment knobs Adaptor Bracket 8575 Magellan Parkway, Suite 1000 Richmond, VA T: F:

2 Table of Contents Adaptor Bracket Installation Graco Peg Perego Chicco Baby Trend Britax Evenflo Safety 1st 8 Cybex Maxi Cosi 2

3 Adaptor Bracket Installation 1 Un-Velcro both black straps underneath the stroller seat and unsnap all seat snaps below the fold mechanism on the stroller frame. Lift seat fabric up to expose the lower portion of the stroller frame. 2 Loosen adjustment knobs on Adaptor Bracket. From the right side of the stroller, position the lower bar of the Adaptor Bracket under the stroller frame and slide toward the center of the stroller. Rivets Snaps 3 Wrap the center clamp around the metal frame bar in the Tighten both adjustment knobs until center clamp is secured onto the stroller frame. 4 On the right side of the stroller frame, position the right clamp below the 2 rivets and between the two snaps on the frame. Tighten the adjustment knob until the right clamp is secured onto the stroller frame. 5 Pull stroller seat fabric down and snap into place. Re-attach both black Velcro straps behind stroller frame. 6 Please proceed to the page labeled with your car seat brand for further instructions. For use with one child in car seat and one child in left stroller seat: Make sure the adaptor bracket is locked into place on the right side of the stroller. Press red compression lock down to secure the Adaptor Bracket in place. For use with one child in car seat only: Lift up on red compression lock and slide adaptor bar to the center of the stroller. Press red compression lock down to lock into place. 3

4 Graco Uses the Adaptor Bracket, U-shaped bar (A), U-shaped bar (B), Spring support bar (C), and Graco support bar (D) The car seat adaptor comes fully assembled for use with Graco model car seats. Should you detach the spring support bar (C) or Graco support bar (D) and need to reassemble, please see Support Bar Configuration below for instructions. Car Seat Adaptor Installation: 1 Open the compression locks on the Adaptor Brackets by flipping the red latches up. 2 Insert the U-shaped bar (A) into the openings on the front of the adaptor brackets. 3 Close the compression locks on the adaptor brackets by flipping the red latches down, locking the U-shaped bar (A) in place. Indicator 4 From the rear of the stroller, connect the second U-shaped bar (B) over the ends of the already installed U-shaped bar (A) until it clicks into place. You will see only green in the indicator on the top of the bars when the U-shaped bars are locked in place. 5 Place car seat on the car seat adaptor and press down firmly until it clicks into place. Fasten and properly tighten the Adaptor Bracket Safety Belt over the car seat before operation. Support Bar Configuration: 1 Squeeze spring support bar (C) and insert into holes on the inside of U-shapped support bar (B). 4 2 Align the openings of the Graco support bar (D) with the ends of U-shaped support bar (B). Slide The Graco support bar onto the U-shaped bar (B) and snap onto spring support bar (C). You will hear it click when properly attached.

5 Peg-Perego Uses the Adaptor Bracket, U-shaped bar (A), U-shaped bar (B), and the Spring support bar (C) Support Bar Configuration: The car seat adaptor comes fully assembled for use with Graco model car seats. The Graco support bar (D) must be removed prior to attaching your Peg-Perego car seat to the Baby Jogger Car Seat Adaptor. 1 Holding the U-shaped bar (B), unsnap Graco support bar (D) from the Spring support bar (C) and remove. Car Seat Adaptor Installation: 1 Open the compression locks on the Adaptor Brackets by flipping the red latches up. 2 Insert the U-shaped bar (A) into the openings on the front of the adaptor brackets. 3 Close the compression locks on the adaptor brackets by flipping the red latches down, locking the U-shaped bar (A) in place. Indicator 4 From the rear of the stroller, connect the second U-shaped bar (B) over the ends of the already installed U-shaped bar (A) until it clicks into place. You will see only green in the indicator on the top of the bars when the U-shaped bars are locked in place. 5 Place car seat on the car seat adaptor and press down firmly until it clicks into place. Fasten and properly tighten the Adaptor Bracket Safety Belt over the car seat before operation. 5

6 Chicco Uses the Adaptor Bracket, U-shaped bar (A), and the U-shaped bar (B) Support Bar Configuration: The car seat adaptor comes fully assembled for use with Graco model car seats. The Graco support bar (D) and spring support bar (C) must be removed prior to attaching your Chicco car seat to the Baby Jogger Car Seat Adaptor. 1 Holding the U-shaped bar (B), unsnap Graco support bar (D) from the Spring support bar (C) and remove. 2 Squeeze spring support bar (C) and remove from U-shaped support bar (B). Car Seat Adaptor Installation: 1 Open the compression locks on the Adaptor Brackets by flipping the red latches up. 2 Insert the U-shaped bar (A) into the openings on the front of the adaptor brackets. 3 Close the compression locks on the adaptor brackets by flipping the red latches down, locking the U-shaped bar (A) in place. Indicator 4 From the rear of the stroller, connect the second U-shaped bar (B) over the ends of the already installed U-shaped bar (A) until it clicks into place. You will see only green in the indicator on the top of the bars when the U-shaped bars are locked in place. 5 Place car seat on the car seat adaptor and press down firmly until it clicks into place. Fasten and properly tighten the Adaptor Bracket Safety Belt over the car seat before operation. 6

7 Baby Trend, Britax, Evenflo, Safety 1st Uses the Adaptor Bracket, U-shaped bar (A), and the U-shaped bar (B) Support Bar Configuration: The car seat adaptor is ready to use for Graco model car seats right out of the box. The Graco support bar (D) and Spring support bar (C) must be removed prior to attaching your car seat to the Baby Jogger Car Seat Adaptor. 1 Holding the U-shaped bar (B), unsnap Graco support bar (D) from the Spring support bar (C) and remove. 2 Squeeze spring support bar (C) and remove from U-shaped support bar (B). Car Seat Adaptor Installation: 1 Open the compression locks on the Adaptor Brackets by flipping the red latches up. 2 Insert the U-shaped bar (A) into the openings on the front of the adaptor brackets. 3 Close the compression locks on the adaptor brackets by flipping the red latches down, locking the U-shaped bar (A) in place. Indicator 4 From the rear of the stroller, connect the second U-shaped bar (B) over the ends of the already installed U-shaped bar (A) until it clicks into place. You will see only green in the indicator on the top of the bars when the U-shaped bars are locked in place. 5 Place car seat on the car seat adaptor. Fasten and properly tighten the Bracket Adaptor safety belt over the car seat before operation. 7

8 Car Seat Installation: Cybex & Maxi Cosi Uses the Adaptor Bracket (no support bars are needed) 1 Place car seat on the car seat Adaptor Brackets and press down firmly until it clicks into place. 1 Fasten and properly tighten the Adaptor Bracket Safety Belt over the car seat before operation. 8