Quick Start Operation

Transcription

1 Quick Start Operation Series 98/98E DBS/DTH Systems 1. FIRST, turn ON the Satellite Receiver and the TV monitor. 2. Press the Antenna Control Panel POWER key to turn power to the pedestal ON: Wait 10 to 90 seconds while the antenna initializes itself and automatically acquires the satellite signal. When the antenna is tracking a good satellite signal the TRACKING lamp will be illuminated steady green. If there is no TV picture, check to see if the satellite signal is blocked by the ship s structure or other obstruction. Also confirm that the Satellite Receiver is set up correctly (see the Satellite Receiver manual). It is also possible that the antenna is tracking the wrong satellite, in which case go to Step To choose a different satellite: On the Sea Tel Antenna Control Panel press the NEXT key. The antenna will automatically search for and, within 10 to 30 seconds, acquire a signal from an adjacent satellite. If it is not the desired satellite, press the NEXT key again. 4. On European/Linear systems, maximize the received signal level shown on the receiver setup menu by adjusting the antenna polarization with the UP and DOWN arrow keys. When the UNWRAP lamp is illuminated steady yellow it indicates that the antenna has reached an end stop and is automatically returning to a central operating position. The TV signal will be lost for approximately 30 seconds while the antenna completes its unwrap operation. 5. Once the desired primary or secondary satellite has been acquired as in Step 3 above, future start-ups of the system will be easier by pressing and holding the SAVE key for 6 seconds to save the ID code and position of each satellite. See the Operation Manual for details.

2 ANTENNA CONTROL PANEL FUNCTIONS + + TRACKING LED UNWRAP LED Turns DC power to the Pedestal ON. Both panel LED s illuminate for 5 seconds to indicate INITIALIZATION is in process. Press again to turn DC power to the Pedestal OFF. Press to switch between primary and secondary satellites or search for the next satellite. Press and hold for 6 seconds to clear previously saved primary and secondary satellite ID codes and positions. In Operation Mode, press and HOLD for 6 seconds to save the current satellite ID code, position and polarization. In SETUP Mode, press to save changes to the selected parameter. In SETUP Mode, press and HOLD for 6 seconds to save all parameters and exit SETUP Mode. Moves elevation angle UP one degree per momentary key press. This also exits SETUP mode without permanently saving any parameter changes Press to moves elevation angle DOWN one degree per momentary key press. Press and hold for 6 seconds to access SETUP mode (See manual for details). Moves polarization angle UP one degree per momentary key press (Euro/Linear systems only). Moves polarization angle DOWN one degree per momentary key press (Euro/Linear systems only). ON steady indicates that the antenna is tracking a satellite signal. Flashing indicates that the satellite signal is too low, tracking has been lost. LED is OFF during SEARCH or UNWRAP. ON steady indicates antenna in cable UNWRAP. Flashing indicates antenna is searching for a satellite signal. Sea Tel is ISO 9001 Certified by NSAI Sea Tel, Inc Shary Court Concord, CA Tel: (925) Fax: (925) seatel@seatel.com Web: Look to the Leader. Look to Sea Tel. Sea Tel Europe Unit 1, Orion Industrial Centre Wide Lane, Swaythling Southampton, UK S0 18 2HJ Tel: 44 (0) Fax: 44 (0) europe@seatel.com Web: Doc Rev A

3 1898 Section 7 TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS 7.1. Radome Size Diameter 20 inch (50.8cm) Height 21 inch (53.3cm) Weight 35 Pounds (15.6kg) Mounting 4 bolts on 9-inch (22.86cm) centers 7.2. Antenna Type Spun Aluminum Parabola Size 18 inch (45.7cm) F/D Feed Center focus Splash Plate Gain 31 dbic 12.2 GHz DBS LNF Assembly Sea Tel P.N.: Type: Prime focus, dual output LNB Manufacturer: RCA, but may vary RF Frequencies: GHz IF Frequency: MHz LO Frequency: GHz Noise Figure: 1.2 db max. Polarization modes: LH and RH circular Polarization control: 13/18v switch selectable Galaxy Latin America LNF Assembly Sea Tel P.N.: Type: Prime focus, dual output LNB Manufacturer: Sharp, but may vary RF Frequencies: GHz IF Frequency: MHz LO Frequency: 10.5 GHz Noise Figure: 1.2 db max. Polarization modes: LH and RH circular Polarization control: 13/18v switch selectable 7-1

4 Section 7 TECHNICAL SPECIFICATIONS Stabilized Pedestal Type Stabilization Stab Accuracy Level, Train Motors Pol skew Motor Inertial Reference Gravity Reference Azimuth Reference Tracking rates Roll/Pitch AZ./Turn Range of Motion Elevation Azimuth Polarization Roll Pitch Three-axis: Elevation, Azimuth and Polarization 3 Dimensional Velocity mode Servo 1.5 degrees MAX, 0.7 degrees RMS in presence of specified ship motions. Size 23 DC Step Motors with PWM Microstep drive Size 17 DC Step Motor 3 axis Solid State Quartz Rate Sensors Two Axis Fluid Tilt Sensor Closed Loop Tracking on Satellite signal > 40 degrees / second > 25 degrees / second 10 to 80 degrees 680 degrees +/- 90 degrees +/- 25 degrees (implied) +/- 15 degrees (implied) Elevation Pointing +/- 15 degrees of Roll 25 to 65 degrees +/- 25 degrees of Roll 35 to 55 degrees 7.4. Pedestal Control Unit Size Features Connectors Below Decks Interface Elevation/Azimuth Motors RF Signal Monitor Type F (2) 5 x 11 x 1.2 inches (12.7 x 27.9 x 3.05 cm) Fully integrated controller, sensors, motor drivers, and RF signal monitor. No external components. 15 pin D-Sub at PCU 9 pin HD CPC at Pedestal Base 9 pin D-Sub 7-2

5 1898 Section 7 TECHNICAL SPECIFICATIONS Satellite Identification Receiver Input Range Sensitivity Bandwidth Tuning range Polarity switching DiSEqC detection: Satellite ID QPSK Demodulator FEC Decoder Pipeline Decoder -75 to 45 dbm 30 mv / db typical 27 MHz 950 to 2150 MHz in 1 MHz increments 13/18 volts from receiver 22kHz continuous tone for band switching (Europe) 22kHz pulse tone for satellite switching (Europe) 22kHz continuous tone for satellite switching (US) Network ID for DVB signals. QPSK demodulator lock for DSS signal to symbols per second range 1/2, 2/3, 3/4, 5/6, 6/7, 7/8 rates. Automatically detected DVB or DSS compatible Below Decks Interface Size Display Controls Indicators Serial Interface Connectors DC Power Pedestal Interface RS-232 Interface 3 inch x 5 inch (7.62 x 12.7cm) panel 2 Line, 16 Character Backlit LCD 5 integrated touch switches 2 LED status indicators 9600 baud RS-232 Interface for diagnostics and computer interface. 2 Screw Terminals 8 Screw Terminals 9 Pin Male D-Sub connector (DTE) 7.6. Power Requirements Voltage Current Transient Protection Load Dump Inductive coupling Reverse Battery 24V Jump Start VDC normal operating range 2.4 Amps 13.8 VDC 60 volts +/- 1 usec Indefinite 1 minute 7-3

6 Section 7 TECHNICAL SPECIFICATIONS Environmental Temperature -20 to +55 degrees C. Humidity Up to 40 degrees C. Rain Up to 4 inches per hour. Degraded RF performance when the radome surface is wet. Wind Up to 100 knots from any direction. Corrosion Parts are corrosion resistant or treated to endure effects of salt air and salt spray. Ship Motions for specified pointing accuracy Roll +/-25 degrees with 6-12 sec periods Pitch +/-15 degrees with 6-12 sec periods Yaw +/-8 degrees with 15 to 20 sec periods Turning rate Up to 12 deg/sec. 7-4