1 INTERNATIONAL STANDARD IEC First edition Dit document mag slechts op een stand-alone PC worden geinstalleerd. Gebruik op een netwerk is alleen. toestaan als een aanvullende licentieovereenkomst voor netwerkgebruik met NEN is afgesloten. This document may only be used on a stand-alone PC. Use in a network is only permitted when a supplementary license agreement for us in a network with NEN has been concluded. Video systems (525/60) Video and accompanied data using the vertical blanking interval Analogue interface Part 2: 525 progressive scan system Reference number IEC :2002(E)
2 Publication numbering As from 1 January 1997 all IEC publications are issued with a designation in the series. For example, IEC 34-1 is now referred to as IEC Consolidated editions The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is also available from the following: IEC Web Site ( Catalogue of IEC publications The on-line catalogue on the IEC web site ( enables you to search by a variety of criteria including text searches, technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications ( justpub/jp_entry.htm) is also available by . Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Tel: Fax:
3 INTERNATIONAL STANDARD IEC First edition Video systems (525/60) Video and accompanied data using the vertical blanking interval Analogue interface Part 2: 525 progressive scan system IEC 2002 Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone: Telefax: Web: Commission Electrotechnique Internationale International Electrotechnical Commission PRICE CODE For price, see current catalogue F
4 IEC:2002(E) CONTENTS FOREWORD Scope Definitions and abbreviations Construction of identification signal Bit and code assignment of the identification signal General WORD-0: Identification data for the video information signal WORD-1 and WORD CRCC Transmission frame Designation... 7 Annex A (normative) Aspect ratio and picture display format... 8 A.1Aspect ratio... 8 A.2 Picture display format... 8 Annex B (normative) Copy control information system... 9 B.1Copy control information... 9 B.2 CGMS-A... 9 B.3 APS trigger bit...10 B.4 Analogue source bit...10 Figure 1 Identification signal waveform... 4 Figure 2 Signal inserted line in vertical blanking interval... 4 Figure 3 Identification data format... 5 Figure 4 CRCC generator... 6 Figure A.1 Aspect ratio Figure A.2 Picture display format... 7 Table 1 Aspect ratio and display format Table B.1 Bit assignment of WORD Table B.2 CGMS-A... 8 Table B.3 Bit assignment of CGMS-A... 9 Table B.4 Bit assignment of APS trigger bits... 9 Table B.5 Bit assignment of analogue source bit...10
5 IEC:2002(E) 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION VIDEO SYSTEMS (525/60) VIDEO AND ACCOMPANIED DATA USING THE VERTICAL BLANKING INTERVAL ANALOGUE INTERFACE Part 2: 525 progressive scan system FOREWORD 1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, the IEC publishes International Standards. Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical specifications, technical reports or guides and they are accepted by the National Committees in that sense. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of its standards. 6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC has been prepared by IEC technical committee 100: Audio, video and multimedia systems and equipment. The text of this standard is based on the following documents: FDIS 100/444/CDV Report on voting 100/502/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended.
6 1 Scope IEC:2002(E) VIDEO SYSTEMS (525/60) VIDEO AND ACCOMPANIED DATA USING THE VERTICAL BLANKING INTERVAL ANALOGUE INTERFACE Part 2: 525 progressive scan system This part of IEC specifies the aspect ratio code and the copy control information code and the method of transfer of these codes in the vertical blanking interval of the luminance signal. It is applicable to the transfer of video related information with the video signal through the baseband analogue signal of the 525-line/60-frame progressive scan video system. This standard is applicable to analogue video signal interfaces between digital and analogue video equipment as follows: digital video equipment to digital video equipment; digital video equipment to analogue video equipment; analogue video equipment to digital video equipment; analogue video equipment to analogue video equipment. 2 Definitions and abbreviations For the purposes of this document the following definitions and abbreviations apply. 2.1 CRCC cyclic redundancy check code for error detection 2.2 CGMS-A copy generation management system on analogue video interface, for use in digital video recorders and players 2.3 APS analogue protection system, to control analogue copying from digital transmission or from digital copies of a video signal 2.4 IRE linear scale for measuring the relative amplitude of the video signal with a reference at the blanking level, in which pure white is defined as 100 IRE and the blanking level is 0 IRE. NOTE IRE is the abbreviation for the Institute of Radio Engineers.
7 Bestelformulier Stuur naar: NEN Standards Products & Services t.a.v. afdeling Klantenservice Antwoordnummer WB Delft Ja, ik bestel NEN Standards Products & Services Postbus GB Delft Vlinderweg AX Delft T (015) F (015) ex. IEC :2002 en Videosystemen (525/60) - Video- en erbij behorende gegevens die gebruikmaken van de verticale onderdrukkingsinterval - Analoog interface - Deel 2: 525 Progressief scansysteem Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via Gratis nieuwsbrieven Wilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen, normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze nieuwsbrieven. Gegevens Bedrijf / Instelling T.a.v. O M O V Klantnummer NEN Uw ordernummer BTW nummer Postbus / Adres Postcode Plaats Telefoon Fax Factuuradres (indien dit afwijkt van bovenstaand adres) Postbus / Adres Postcode Plaats Datum Handtekening Retourneren Fax: (015) Post: NEN Standards Products & Services, t.a.v. afdeling Klantenservice Antwoordnummer 10214, 2600 WB Delft (geen postzegel nodig). Voorwaarden De prijzen zijn geldig tot 31 december 2016, tenzij anders aangegeven. Alle prijzen zijn excl. btw, verzend- en handelingskosten en onder voorbehoud bij o.m. ISO- en IEC-normen. Bestelt u via de normshop een pdf, dan betaalt u geen handeling en verzendkosten. Meer informatie: telefoon (015) , dagelijks van 8.30 tot uur. Wijzigingen en typefouten in teksten en prijsinformatie voorbehouden. U kunt onze algemene voorwaarden terugvinden op: Normalisatie: de wereld op één lijn. preview