2.2 MA Rear Panel
|
|
- Alfred Riley
- 7 years ago
- Views:
Transcription
1 2.2 MA Rear Panel 1. FUSE Designed to prevent overcurrent from passing through the MA-500. Always use the fuse supplied. 2. GENLOCK Connector Inputs the VBS or BBS signal for external synchronization. Bridge connection is enabled. 3. RET-1/RET-2 Connector Inputs the camera head transmit signal (return signal). Bridge connection is enabled. (2 channels) 4. ENC-1/ENC-2 Connector Outputs the ENC signal. (2 channels) 5. SDI OUT 1/SDI OUT 2 Outputs the SDI signal at 270Mbps. (2 channels) 6. AUDIO OUT Connector Outputs the audio signal sent from the camera head. 7. REMOTE Connector Connects to the external remote controller such as OCP-399/RCP CAMERA Connector Connects to the VTR connector of the camera adaptor with the optional MCC cable. 9. INTERCOM Connector Connects to the external intercom system. 10. TALLY OUT Connector Outputs the tally signal for image monitoring. 11. TALLY IN Connector Inputs the tally control signal from the external system. 12. SYNC Connector Outputs SYNC in synchronization with the image signal. SYNC OUT refers to the sync separation from the ENC signal that is output from the camera. Slight phase difference is detected compared to the RGB signal and component signal.
2 13. B/Cb/C Connector Outputs the B, Cb, or C signal selected with the OUT PUT select switch. 14. G/Y/Y Connector Outputs the G/Y (component) or Y (Y/C) signal selected with the OUT PUT select switch. 15. R/Cr/- Connector Outputs the R or Cr signal selected with the OUT PUT select switch. 16. OUT PUT Select Switch Allows switchover from the output signals delivered from connectors #13 to 15 to the RGB signal and component signal, or to the Y/C signal. 17. Cooling Fan Designed to cool down the internal temperature. 18. AC IN Connector Supplies the AC power. 19. Q-TV IN LOOP THROUGH Inputs the Q-TV signal (prompter signal) to the camera adaptor, with the optional Q-TV module mounted. Bridge connection is enabled.
3 3. Installing and Connecting Devices 3.1 System Diagram (*1) MCC Cable MAX:300m Note: Only the devices shown above must be connected to the unit. If this warning is disregarded, it may cause potential damage or failure of a device.
4 3.2 Connection with The Camera Head * Always connect the color camera and MA-500 using the dedicated MCC cable. (VTR cable not available) * The MA-500 is capable of outputting the RGB signal or Y/Cb/Cr signal. The RGB / YCbCr select switch, which is located on the MA-500 rear panel, configures the output setting. (See the figure right) Notice Switch the camera head adaptor switch fully to output the Y/C signal. Reference See section Output of the Y/C image signal for outputting the Y/C signal. * The camera cable (MCC cable) should be connected, keeping away from main power sources, noise sources (such as construction drills), and mainframe computers. * Do not connect the remote controller to the camera head when the MA-500 is in use. The camera will become inoperable if this warning is disregarded. Notice Camera Power Supply The color camera draws its power through the MA-500 camera dedicated cable (MCC cable) when connected to the MA-500.
5 <Connection with SDI Devices> SDI output is to be connected to the SDI OUT connector "1" or 2. This connection has no effect on the image signal to be output. Connection with the SDI devices requires a coaxial cable. The MA-500 is capable of outputting the RGB signal or Y/Cb/Cr signal. The RGB / YCbCr select switch, which is located on the MA-500 rear panel, configures the output setting. (See the figure right) Notice Always use a D1 input-capable monitor when connecting the SDI output to the monitor. Notice If the Y/C image signal is output through the OUT PUT connector located on the MA-500 rear panel (see the figure right), no SDI image signal will be output.
6 3.3 Camera Adaptor Setup This section describes the connection settings of the MA-500 Camera Control Unit. Refer to the HL-65W Operation Manual for settings to connect with other devices. <CA-65> 1. INCOM Jack Used to communicate with the MA-500. The headset for intercommunication should conform to the following standards: Connector: 5-pin (NTSC) XLR connector (male plug) 7-pin (PAL) XLR connector (male plug) 2. VTR Connector Used to connect to the MA-500. Despite extension possible up to a maximum of 300m. Notice The cable switch on the MA-500 FRONT PANEL should be set in accordance with the length of the camera cable used. 3. MIC LEVEL Select Switch This switch needs to be set on -20dB to establish connection with the MA-500. Notice Use of MA-500 Camera Control Unit with the CA-65 adaptor requires reconfiguration of the camera head menu. Make the adjustment, as shown below, in VTR REC CONTROL in the maintenance menu. Reference Refer to the camera head operation manual for menu operation. Camera head menu (VTR/26P INTERFACE) Adjustment Item Set Value 1 26P VIDEO SEL COMP Reference See section Output of the Y/C image signal for outputting the Y/C signal.
7 3.4 Connection with the Remote Controller * For remote-control operation of the unit, the CONTROL switch on the MA-500 FRONT panel needs to be set to REMOTE". The diagonally shaded area in the figure of the MA-500 FRONT panel (see below) will become inoperable when this is done. Notice Always turn OFF the POWER switch on the MA-500 before operating the MA-500CONTROL select switch and connecting the remote controller.
8 3.5 Pin Function of Connectors TALLY IN Connector Insertion side This is the connector to input the tally control signal. Body side : PRC03-21A10-7M(Tajimi) Cable side : PRC03-12A10-7F10.5(7 pin female plug) or equivalent Pin Number Name Function Direction External Interface A R TALLY(+) R TALLY input(+) IN B G TALLY(+) G TALLY input(+) IN C R TALLY(-) R TALLY input(-) IN D G TALLY(-) G TALLY input(-) IN E NC F NC G GND Ground for R and G TALLYs(+) GND Control DC voltage input is non-polar. For "MAKE",either(1) or (2) can be used. The tally mode can be switched with S3 and S4 switches(power/make SELECT) on the MPU module in the MA-500. TALLY OUT Connector Insertion side This is the connector to output the tally control signal. Body side : PRC05-RB5F(Tajimi) Cable side : PRC05-P5M(5 pin male plug) or equivalent Pin Number Name Function Direction External Interface A +12V OUT +12V power output OUT B R TALLY R TALLY output OUT C NC D G TALLY G TALLY output OUT E TALLY GND Ground for TALLY GND
9 INTERCOM Connector Insertion side This is the connector to connect the external intercom system. Body side : TRC01-A25R24MA(TAjimi) Cable side : TRC01-A25P24FA(24 pin famale plug) or equivalent Pin Number Name Function Direction External Interface 1 NC 2 NC 3 NC 4 NC 5 NC 6 ENG MAL(H) ENG CAMLINE(+)/ENG RTS 7 ENG MAL(C) ENG CAMLINE(-) IN OUT IN OUT 8 ENG LMA(H) ENG CAMLINE(+) IN 9 ENG LMA(C) ENG CAMLINE(-) IN 10 SHIELD 11 NC 12 NC Shield for ENG line (6 pin to 9 pin) GND 13 PGM-1 IN(H) PGM-1 line(h) IN 14 PGM-1 IN(C) PGM-1 line(c) IN 15 SHIELD Shield for PGM-1 line (13 pin, 14 pin) GND
10 Pin Number Name Function Direction External Interface 16 NC 17 NC 18 NC 19 NC 20 NC 21 SWITCHABLE ENABLE 22 16:9 ON Aspect ratio select Permission:GND,Prohibition:OPEN Aspect ratio selection(21st pin:gnd) 16:9:GND,4:3:OPEN IN IN 23 NC 24 NC Use ENG line if the external line is a sigle line. All the signals of the intercom line to the external system are delivered with 0dBm, 600ohm. Notice The 2W intercom system is unavailable.
11 INTERCOM Connector XLR-5 Type Connector This is the connector to connect the headset for intercom. Body side : XLR-5-31-F77 (ITT Canon) Cable side : XLR-5-12C (5 pin male plug) or equivalent. Insertion side Pin Number Name Function Direction External Interface 1 TALK(C) Shielding for intercom microphone input(h) GND 2 TALK(H) Intercom microphone input(h) IN 3 SHIELD Shielding for LISTEN Lch or LISTEN Rch output GND 4 LISTEN Lch(H) LISTEN Lch output(h) OUT 5 LISTEN Rch(H) LISTEN Rch output(h) OUT XLR-7 Type Connector This is the connector to connect the headset for intercom. Body side : XLR-7-31-F77 (ITT Canon) Cable side : XLR-7-12C (7 pin male plug) or equivalent. Insertion side Pin Number Name Function Direction External Interface 1 LISTEN L(C) Shielding for intercom reciver L output(h) 2 LISTEN L(H) Intercom receiver L output(h) 3 TALK(C) Shielding for intercom microphone Input(H) 4 TALK(H) Intercom microphone input(h) 5 COMM COMM GND terminal 6 LISTEN R(H) Intercom receiver R output(h) 7 LISTEN R(C) Shielding for intercom reciver R output(h)
12 AUDIO OUT Connector. It outputs the audio signal sent from the CAMERA. Body side : XLR-3-32-F77 (ITT Canon) Cable side : XLR-3-11C (3 pin famale plug) or equivalent. Insertion side Pin Number Name Function Direction External Interface SHIELD Shielding for microphone output(h) GND MIC OUT(H) Microphone output(h) form camera head OUT MIC OUT(C) Microphone output(l ) form camera head OUT REMOTE Connector Insertion side This is the connector for the external remote control panel. Body side : PRC05-RB8F(Tajimi) Cable side : PRC05-PB8M (8 pin male plug) Pin Number A B C D Name Function Direction External Interface HED(+) Digital data output(+) from camera head to remote controller OUT HED(-) Digital data output(-) from camera head to remote controller OUT HEC(+) Digital data input(+) from camera head to remote controller IN HEC(-) Digital data input(-) from camera head to remote controller IN E +12V(REM) DC+12V power supply to remote controller OUT F +12V RET(REM) Ground for DC+12V power supply RET G REM LISTEN Audio input for intercom from remote controller IN H REM TALK Audio output for intercom from remote controller OUT
13 4. Setup 4.1 Intercom Setup Connection with the intercom connector on the MA-500 rear panel is required to establish intercommunications. This connection enables intercommunication of the MA-500 with the HL-65W and the switcher. The MA-500 is compatible with 4-wire type, RTS type, and ClearCom type communication methods Selection between Intercom 4-wire, RTS, and ClearCom communication methods (1) Unscrew the screws (5 pcs.) from the side and rear panels, and remove the top cover. (2) Switch the intercom circuit switches on the main board to their proper positions according to the following table. Switch positions SW No 4-wire RTS ClearCom SW701 OFF (OFF)*1 (OFF)*1 SW702 4W RTS RTS SW703 4W 4W 4W SW705 4W RTS RTS SW706 4W RTS RTS SW707 RTS CL SW708 RTS CL *1: A single line should have an impedance of 200. Note: Do not perform switch reconfigurations other than those above. If this warning is disregarded, it may cause potential malfunction.
14 <Layout of Intercom Circuit Switches on the main board> Setting of Headset Type (1) Unscrew the screws (5 pcs.) from the side and rear panels, and remove the top cover. (2) Apply the switch setting for the FRONT board in accordance with the headset used. Set the switch on Dynamic for use with a dynamic microphone. FRONT BOARD
15 4.2 Video Output Signal Switching Procedure Selection of RGB/Component Signal Output The MA-500 is capable of selection between the RGB and Y/Cr/Cb image signals to output with the use of the RGB / YCrCb select switch located on the MA-500 rear panel. Y/Cr/Cb image signal.set the switch to Y/Cr/Cb. RGB image signal..set the switch to RGB. Notice The camera head is configured to output the component image signal (fixed) despite being set to RGB signal output. The MA-500 converts the Y/Cr/Cb signal to the RGB signal before outputting the signal Output of the Y/C Image Signal The select switch on the MA-500 rear panel allows selection of the Y/C image signal to be output. Y/C image signal Set the switch to Y/C. The camera head requires reconfiguration. Apply the switch setting for the camera adaptor as described below. Open the right panel of the CA-65 adaptor as viewed from rear, and apply the J-BOARD switch setting (S4 and S5). See below. Notice If the switch setting is set for the Y/C image signal to be output, the SDI optional device cannot be installed.
16 4.2.3 Selection of Component Image Signal Level The MA-500 is capable of outputting the component image signal at the level of MII-VCR signal. (1) Unscrew the screws (5 pcs.) from the side and rear panels, and remove the top cover. (2) Set the component circuit select switch (SW401) on the main board to USA M2. <Layout of Component Circuit Switches on the main board>
17 4.3 Tally Signal Setup The tally signal, which is input to the communication connector located on the MA-500 Rear Panel, is compatible with a MAKE contact system and POWER contact system in response to the unit. Selection between MAKE and POWER is achieved by switching between the S3 and S4 switches on the MPU module. MAKE Contact System.Set the S202 switch and S203" switch to MAKE. POWER Contact System.Set the S202 switch and S203" switch to POWER. Reference See section 3.5 Pin Function of Connectors for connection to the unit.
18 5. Installing Options 5.1 Q-TV Module Kit The Q-TV Module Kit is composed of the following parts. Make sure all the parts are in the package prior to installation. The Q-TV-capable camera adaptor is required. <Q-TV Module Kit> Q-TV Module Q-TV BNC Panel Connection Wire Harness (2 pcs.) Column (4 pcs.) Notice Equipped with the module kit listed below, the CA-65 camera adaptor is capable of operation. Installation of a Q-TV-specification Module Kit requires a special tool. Contact our sales or service personnel to install the Q-TV-specification Module Kit. <CA-65 Q-TV-specification Module Kit> Q-TV DEMOD Module
19 <Installation Procedure> (1) Unscrew the screws (4 pcs.) securing the blank panel which is attached to the rear panel, and remove the blank panel. (2) Attach the Q-TV BNC panel. (3) Unscrew the screws (5 pcs.) from the side and rear panels, and remove the top cover. (4) Unscrew the screws (4 pcs.) securing the MPU board, and attach the supplied columns.
20 (5) Mount the Q-TV board on the MPU module and secure it with screws (4 pcs.). (6) Connect the wire harnesses (2 pcs.). Q-TV board CN1 to Q-TV BNC panel Q-TV board CN2 to main board CN3 (7) Set the S801 RET/Q-TV switch on the main board to RET/Q-TV. Notice If the Q-TV adaptor is installed, the S801 RET/Q-TV switch must be set to the RET/Q-TV position irrespective of the use of the Q-TV.
21 <Connection with External Devices>
TELIKOU Intercom System. MS-500(4+1 channel) Main Station Instruction Manual
TELIKOU Intercom System MS-500(4+1 channel) Main Station Instruction Manual TELIKOU Systems All Rights Reserved While TELIKOU makes every attempt to maintain the accuracy of the information contained in
More informationColour Video Monitors PVM-9045QM/9042QM/9040ME PVM-6041QM
Colour Video Monitors PVM-9045QM/9042QM/9040ME Specifications GENERAL 9045QM 9042QM Colour system PAL/SECAM/NTSC/NTSC4.43 The CRT type 22 cm (9-inch) HR Trinitron Tube, pursuit 22 cm of (9-inch) excellence
More informatione-4 AWT07MLED 7 Q TFT LCD MONITOR (LED Backlighted) USER MANUAL
Thank you for purchasing our product. Please read this User s Manual before using the product. Change without Notice AWT07MLED 7 Q TFT LCD MONITOR (LED Backlighted) USER MANUAL e-4 SAFETY PRECAUTIONS Federal
More informationPS 29M DUAL CHANNEL BELTPACK IN METAL CASE
PS 29M DUAL CHANNEL BELTPACK IN METAL CASE USER MANUAL October 2013 This product is designed and manufactured by: ASL Intercom BV Zonnebaan 42 3542 EG Utrecht The Netherlands Phone: +31 (0)30 2411901 Fax:
More informationPSC RF Multi SR Six Pack
PSC RF Multi SR Six Pack The PSC RF Multi SR Six Pack contains two, separate, active 1 x 4 RF splitters for use with up to three slot style receivers. This compact, rugged device was developed using the
More informationProduct Information S N O. Portable VIP protection CCTV & Alarm System 2
Product Information S N O Portable VIP protection CCTV & Alarm System 2 G O V E R N M E N T A L S E C U R I T Y S O L U T I VIP KIT Rapid Deployment VIP Protection Kit The VIP KIT has been designed to
More informationRGB for ZX Spectrum 128, +2, +2A, +3
RGB for ZX Spectrum 128, +2, +2A, +3 Introduction... 2 Video Circuitry... 3 Audio Circuitry... 8 Lead Wiring... 9 Testing The Lead... 11 Spectrum +2A/+3 RGB Differences... 12 Circuitry Calculations...
More informationTELIKOU Intercom System. TM-200 Main Station. Instruction Manual
Intercom System TM-200 Main Station Instruction Manual TELIKOU Systems All Rights Reserved I. Introduction Thank you for choosing TELIKOU intercom product. TM-200 main station is suitable for television
More informationIsumaTV. Media Player Setup Manual COOP Cable System. Media Player
IsumaTV Media Player Setup Manual COOP Cable System Visual Setup Front: Router Scan Converter Media Player Video Modulator Equipment: Media Player: Router: Scan Converter: Video Modulator: This computer
More information1 All safety instructions, warnings and operating instructions must be read first.
ONYX USER MANUAL 2 Dateq ONYX Manual Safety instructions EN Safety instructions 1 All safety instructions, warnings and operating instructions must be read first. 2 All warnings on the equipment must be
More informationIPX AUTOMATIC IP NETWORK LOSS BACKUP A/B SWITCH INSTRUCTION BOOK IB6444-02
IPX AUTOMATIC IP NETWORK LOSS BACKUP A/B SWITCH INSTRUCTION BOOK IB6444-02 TABLE OF CONTENTS DESCRIPTION 2 MOUNTING INSTRUCTIONS 2 HOW TO CABLE THE IPX 2/3 POWER SUPPLY INSTALLATION 3 OPERATION 3 CARE
More information16-Port RS232 to USB2.0 High Speed Multi Serial Adapter (w/ Metal Case) Installation Guide
16-Port RS232 to USB2.0 High Speed Multi Serial Adapter (w/ Metal Case) Installation Guide 1. Introduction Thank you for purchasing this 16-Port RS232 to USB2.0 High Speed Multi Serial Adapter. It is an
More informationPS 155 WIRELESS INTERCOM USER MANUAL
PS 155 INTERFACE TO SIMPLEX WIRELESS INTERCOM USER MANUAL Issue 2011 ASL Intercom BV DESIGNED AND MANUFACTURED BY: ASL INTERCOM BV ZONNEBAAN 42 3542 EG UTRECHT THE NETHERLANDS PHONE: +31 (0)30 2411901
More informationTOA INTERCOM SYSTEM. TOA Corporation OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS TOA INTERCOM SYSTEM INTERCOM STATION HF-250M Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend you to keep this manual
More informationOptions for ABB drives, converters and inverters. User s manual FDPI-02 diagnostics and panel interface
Options for ABB drives, converters and inverters User s manual FDPI-02 diagnostics and panel interface Table of contents Table of contents 3 1. FDPI-02 diagnostics and panel interface Safety..............................................
More informationAVR 158. Audio/video receiver. Quick-Start Guide ENGLISH
158 Audio/video receiver ENGLISH Quick-Start Guide 158 Introduction, Speaker Placement and Connection Introduction Thank you for choosing a harman kardon product! This quick-start guide contains all the
More informationModular I/O System Analog and Digital Interface Modules
OPERATING INSTRUCTIONS Modular I/O System Analog and Digital Interface Modules Installation Operation Maintenance Document Information Document ID Title: Operating Instructions Modular I/O System Part
More informationIRT Eurocard. Type DAX-3206. Audio Extractor for 270 Mb/s SDI
I R T Electronics Pty Ltd A.B.N. 35 000 832 575 26 Hotham Parade, ARTARMON N.S.W. 2064 AUSTRALIA National: Phone: (02) 9439 3744 Fax: (02) 9439 7439 International: 61 2 9439 3744 61 2 9439 7439 Email:
More information************* OWNER'S MANUAL BAMF800/2 BAMF1250/2 BAMF1800/2 BAMF2200/2 BAMF2600/2 BAMF1200/4 BAMF1600/4 BAMF2000/1D BAMF4000/1D BAMF5500/1D
************* OWNER'S MANUAL BAMF800/2 BAMF1250/2 BAMF1800/2 BAMF2200/2 BAMF2600/2 BAMF1200/4 BAMF1600/4 BAMF2000/1D BAMF4000/1D BAMF5500/1D INTRODUCTION Power Acoustik amplifiers provide high-performance
More information22X DSP COLOR ZOOM CAMERA AUTO FOCUS ZOOM CAMERA
Instruction Manual 22X DSP COLOR ZOOM CAMERA AUTO FOCUS ZOOM CAMERA OPERATION / INSTALLATION MANUAL Thank you for using this product. Please read this manual carefully before use, Please keep this instruction
More informationFeatures, Benefits, and Operation
Features, Benefits, and Operation 2014 Decibel Eleven Contents Introduction... 2 Features... 2 Rear Panel... 3 Connections... 3 Power... 3 MIDI... 3 Pedal Loops... 4 Example Connection Diagrams... 5,6
More informationLOXONE 12 Channel Amplifier
LOXONE 12 Channel Amplifier Item no.: 200110 Thank you for purchasing the Loxone Twelve Channel Amplifier. The versatility of the Amplifier makes it the perfect choice for almost every type of custom multi-room
More informationUCC 1 USB-CAN CONVERTER
Owner s Manual UCC 1 USB-CAN CONVERTER Contents 1. Description... 17 2. Controls and Connections... 18 3. Installation... 19 3.1 Unpacking... 19 3.2 Rack-Mounting... 19 4. Initial Operation... 20 4.1 PC
More informationHP4000EX Hardware Manual
INFORMATION TO USER CAUTION RISK OF ELECTRIC SHOCK, DO NOT OPEN! CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
More informationCaracterísticas. Starligh SA 9 de julio 1595 Córdoba Argentina - 0351-4809210 / 4119600
Balun Activo - BALUN_ACT Características Single Channel Active Video Transmitter Full-motion color video signal up to 3900ft(1200m) via UTP cat5e/6 NTSC, PAL & SECAM video format compatible Real-time transmission
More informationUser Manual. Please read this manual carefully before using the Phoenix Octopus
User Manual Please read this manual carefully before using the Phoenix Octopus For additional help and updates, refer to our website To contact Phoenix Audio for support, please send a detailed e-mail
More informationInstruction Manual RT-94845SL RR-94845SL Forty-Eight Channel Video Multiplexer With Bi-directional Ethernet Data
Instruction Manual RT-94845SL RR-94845SL Forty-Eight Channel Video Multiplexer With Bi-directional Ethernet Data Copyright 2007, American Fibertek, Inc. 0411JD Table of Contents Functional Description...3
More informationHear The Future...Now! SIEM-2T/SIEM-2R
Hear The Future...Now! SIEM-2T/SIEM-2R UHF PLL Mono In Ear Monitoring System 856 59508-03 ATTENTION Please pay high attention to the following information. The guideline published by Occupational Safety
More informationLine Level Converter Box. S Class Signal Processors
Line Level Converter Box S Class Signal Processors Table Of Contents Introduction and Features 3 Front and Rear Panel Layout 4 Operating the S convert Using the LEVEL controls 5 Typical Set-up 6 Wiring
More informationRS232C < - > RS485 CONVERTER S MANUAL. Model: LD15U. Phone: 91-79-4002 4896 / 97 / 98 (M) 0-98253-50221 www.interfaceproducts.info
RS232C < - > RS485 CONVERTER S MANUAL Model: LD15U INTRODUCTION Milestone s model LD-15U is a RS232 to RS 485 converter is designed for highspeed data transmission between computer system and or peripherals
More informationInnkeeper PBX. Desktop Digital Hybrid. User Guide. JK Audio
Innkeeper PBX Desktop Digital Hybrid User Guide JK Audio Introduction Innkeeper PBX will allow you to send and receive audio through your multi-line PBX, ISDN or analog telephone. While this may seem like
More informationIRT Eurocard. Types DAX-3200
I R T Electronics Pty Ltd A.B.N. 35 000 832 575 26 Hotham Parade, ARTARMON N.S.W. 2064 AUSTRALIA National: Phone: (02) 9489 3744 Fax: (02) 9439 7439 International: +61 2 9439 3744 +61 2 9439 7439 Email:
More informationHyperSound System (HSS) Demo and Evaluation Systems Set-Up and Operation Guide
HyperSound System (HSS) Demo and Evaluation Systems Set-Up and Operation Guide Follow this step-by-step guide for an optimal installation. Included: ü 2 HSS Emitters (Speakers) ü 2 Sets of Red & Black
More informationHCS-3600MB2 Conference Main Unit
HCS-3600MB2 Conference Main Unit Features TCP/IP communication protocol in PC control Remote control, remote diagnosis and remote update Parallel redundancy & multi-room configuration Excellent immunity
More information. ImagePRO. ImagePRO-SDI. ImagePRO-HD. ImagePRO TM. Multi-format image processor line
ImagePRO TM. ImagePRO. ImagePRO-SDI. ImagePRO-HD The Folsom ImagePRO TM is a powerful all-in-one signal processor that accepts a wide range of video input signals and process them into a number of different
More informationSmarthome SELECT Bluetooth Wireless Stereo Audio Receiver and Amplifier INTRODUCTION
Smarthome SELECT Bluetooth Wireless Stereo Audio Receiver and Amplifier INTRODUCTION The Smarthome SELECT Bluetooth Wireless Stereo Audio Receiver and Amplifier is a multi-functional compact device. It
More informationCX Zoner Installation & User Guide
CX Zoner Installation & User Guide Cloud Electronics Limited 140 Staniforth Road, Sheffield, S9 3HF England Tel +44 (0)114 244 7051 Fax +44 (0)114 242 5462 e-mail info@cloud.co.uk web site http://www.cloud.co.uk
More informationSVC400P/SVC800P. 4/8 Camera Live Tracking Vehicle DVR Installation Manual. Version 1.0
SVC400P/SVC800P 4/8 Camera Live Tracking Vehicle DVR Installation Manual Version 1.0 1. MAIN FEATURES... 2 2. PRODUCT OVERVIEW... 2 3. DIMENSIONS... 4 4. PACKAGE CONTENTS... 5 5. MOUNTING AND ENVORNMENTAL
More informationMISE - STEREO ENCODER
MISE - STEREO ENCODER 1. FRONT PANEL CONTROLS and INDICATORS AUDIO LEVEL F1 F2 F3 F4 OVER- MOD F5 F1:AUDIO LEVEL Control The setting of this screwdriver adjustment determines the audio input signal level.
More informationResearch RF Sputtering Packages
Research RF Sputtering Packages Shown with 3" Polaris Adjustable Position Source with Tilt and Shutter 300 or 600 Watt Low Cost Packages for Those With Limited Budgets Desiring Full Capability 13.56 MHz
More informationMini Effect Gizmo. User s Manual. RJM Music Technology, Inc.
Mini Effect Gizmo User s Manual RJM Music Technology, Inc. Mini Effect Gizmo User s Manual Version 1.3 September 26, 2013 RJM Music Technology, Inc. 2525 Pioneer Ave #1 Vista, CA 92081 E-mail: support@rjmmusic.com
More informationZMR 80 STEREO MODULAR ZONER USERS MANUAL
ZMR 80 STEREO MODULAR ZONER USERS MANUAL Lime Technologies http://limetechnologies.co.uk Tel: 08712 233127 ZMR80 Stereo Modular Zoner Mixer Introduction The modular construction of the ZMR80 allows it
More informationVZ-M7 HDMI Field Monitor 7 Class HD LCD
VZ-M7 HDMI Field Monitor 7 Class HD LCD The VZ-M7 HDMI monitor provides sharp, accurate images for improved framing and focus assist on any camera equipped with an HDMI output. Utilizing top-quality Grade
More informationAmplifier for Small Magnetic and Electric Wideband Receiving Antennas (model AAA-1B)
Amplifier for Small Magnetic and Electric Wideband Receiving Antennas (model AAA-1B) 1. Description and Specifications Contents 1.1 Description 1.2 1.2 Specifications 1.3 1.3 Tested parameters in production
More informationUSER MANUAL. 914 Power Amplifier MODEL: P/N: 2900-300280 Rev 1
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: 914 Power Amplifier P/N: 2900-300280 Rev 1 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 3 Overview 3 3.1 Energy Star 3
More informationSystem Wiring Design Guide
System Wiring Design Guide This guide will help demonstrate the various types of wiring solutions available when connecting video surveillance cameras to EZ Watch Pro and Armor Pro Digital Video Recorders.
More informationBusiness/Home GSM Alarm System. Installation and User Manual
Business/Home GSM Alarm System Installation and User Manual Brief Introduction: GSM 900/1800/1900 bands, can be used in most parts of the world Full duplex communication with the host Monitor the scene
More informationPERSONAL MONITOR MIXER/HEADPHONE AMP. S Class Signal Processors
PERSONAL MONITOR MIXER/HEADPHONE AMP S Class Signal Processors Table Of Contents Features 3 Front and Rear Panel Layout 4 Operating the S monitor 5-7 Specifications 8 Wiring Guide 8 Copyright 2003, Samson
More informationKleuren camera PAL : 512 (H) X 582 ( V) NTSC : 512 (H) X 492 (V) CS/ C Mount (Mount adaptor option)
High-Res. CA3003 / KV-41C Picture Elements Control 1/4" SONY Super HAD CCD PAL : 512 (H) X 582 ( V) NTSC : 512 (H) X 492 (V) 3.6mm x 2.7mm PAL / NTSC 420 TV Line VIDEO Auto Tracking white Balance 1.0Lux
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS When using this electronic device, basic precautions should always be taken, including the following: 1. Read all instructions before using the product. 2. Do not use this
More informationF(t) Forssell Technologies Inc
F(t) Forssell Technologies Inc SMP-2Aa Microphone Preamplifier User Manual Forssell Technologies Inc Sandpoint Idaho USA (208) 263-0286 Introduction The Forssell Technologies Inc SMP-2A is a 2 channel,
More informationVIDEO DOOR PHONE SYSTEM
ENGLISH VIDEO DOOR PHONE SYSTEM USER MANUAL Manual covers IH-692 Master and IH-692 Slave Monitors PRECAUTIONS BEFORE INSTALLATION Connect this unit ONLY to other compatible units. Do not connect it to
More informationInstallation and Operation Guide
www.aja.com Quick Start Guide Introduction This Quick Start Guide provides a basic overview of KUMO configuration. It is not meant as a substitute for the detailed information found in the KUMO Manual,
More informationThe basic set up for your K2 to run PSK31 By Glenn Maclean WA7SPY
The basic set up for your K2 to run PSK31 By Glenn Maclean WA7SPY I am by no means an expert on PSK31. This article is intended to help someone get on PSK31 with a K2. These are the things I did to get
More informationEVC40 EMERGENCY VOICE COMMUNICATION SYSTEM
EVC40 EMERGENCY VOICE COMMUNICATION SYSTEM INSTALLATION MANUAL Protec Fire Detection PLC, Protec House, Churchill Way, Nelson, Lancashire, BB9 6RT. Telephone: +44 (0) 1282 717171 Fax: +44 (0) 1282 717273
More informationLT-82 Stationary IR Transmitter
LT-82 Stationary IR Transmitter Configuration LT-82-0 (North America) LT-82-02 (Asia, UK) LT-82-03 (Euro) The Listen LT-82 is the heart of a stationary IR listening system. It takes the desired audio signal
More informationModel: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features
Model: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features Mirror with built in 4.0 LCD Monitor Low Profile, Slim Design High Resolution TFT LCD Built in Speaker Two video inputs Fully
More informationRemote Sources. Facility. Router
A tally display system is an essential part of any broadcast or production environment. It must tell you where signals come from, where they go, and how they are being used. In a typical multi-production
More informationFunktional Technologies. Model: Chocolate Box
Funktional Technologies Model: Chocolate Box November 2013 The Funktional Technologies Chocolate Box is a 2U analog & digital professional audio device. It incorporates two Cadac K type analog input modules.
More informationACCESS CONTROL DOOR PHONES Installation and Programming Manual
ACCESS CONTROL DOOR PHONES Installation and Programming Manual Pantel Pancode Installation and Programming Manual Version 5, Release 7, July 2008 Table of Contents 1 Introduction...1 1.1 Pancode...1 1.2
More informationUser Manual. ATX12V / EPS12V Power Supply TG-I460R (460W+460W) TG-I550R (550W+550W) Switching Power Supply User Manual
ATX12V / EPS12V Power Supply TG-I460R (460W+460W) TG-I550R (550W+550W) User Manual Table of Contents 1 Introduction 2 General specification 3 Installation 4 Pin assignment & function of connectors 5 Drawing
More informationMGL Avionics CAN bus interface for Trig Avionics TT21/TT22 transponders
MGL Avionics CAN bus interface for Trig Avionics TT21/TT22 transponders General The MGL Avionics CAN bus interface for the Trig Avionics TT21 and TT22 transponders provides a simple solution to allow any
More informationSafety Warnings and Guidelines
Safety Warnings and Guidelines Thank you for purchasing this Wireless Speaker Amplifier! For best results, please thoroughly read this manual and carefully follow the instructions. Please pay extra attention
More informationTurbo X. www.smartwireless.co.uk. 594 channel UHF true diversity
Turbo X 594 channel UHF true diversity The new Turbo X series from Smart Wireless is the culmination of two years of research and development into advanced wireless technology. Using sophisticated RF design
More informationInstruction Sheet ACS-101. General Description. Specifications. Amplified Broadband UHF Combiner-Splitter. Overall. Antenna Splitter.
ACS-101 Amplified Broadband UHF Combiner-Splitter General Description The ACS-101 (Antenna Combiner Splitter 10 to 1) is an amplified and filtered broadband splitter-combiner. It allows up to 10 base stations
More informationAV, Data, Power, and Control Connectivity for Wall Mount, Furniture Mount, and Floor Mount Applications
AV, Data, Power, and Control Connectivity for Wall Mount, Furniture Mount, and Floor Mount Applications Description Extron Architectural Adapter Plates are optional mounting plates that fit into designated
More informationZone Mixer. 6 channels configurable from 24 inputs. 3 zone outputs. Expandable via Sys-Link TM Built-in comp/limiter, ducking and alarm functions
GR 1 Zone Mixer W H E N Y O U R E M I X I N G W I T H P R O F E S S I O N A L S 6 channels configurable from 24 inputs. 3 zone outputs. Expandable via Sys-Link TM Built-in comp/limiter, ducking and alarm
More informationSECURITY CAMERA INSTRUCTION MANUAL ENGLISH VERSION 1.0 LBC5451. www.lorextechnology.com
SECURITY CAMERA INSTRUCTION MANUAL ENGLISH VERSION 1.0 LBC5451 www.lorextechnology.com Contents 1x Camera and mounting stand 1x Power adapter 1x Mounting kit 1x Allen key 1x Screw cap 1x 60 ft. (18m)
More informationC24-CAMANL Video Server/Encoder
C24-CAMANL Video Server/Encoder User s Guide Table of Contents CHAPTER 1 INTRODUCTION... 1 Overview... 1 Physical Details - Video Server... 2 Package Contents... 3 CHAPTER 2 BASIC SETUP... 4 System Requirements...
More informationDriver Pant 8 and antenna switcher Ant 8. User manual
Driver Pant 8 and antenna switcher Ant 8 User manual Table of contents Table of contents... 2 Introduction... 3 Shipping Contents... 3 Technical Data... 3 Control Panel... 4 Rear panel... 5 Controller
More informationMirror Mount Video Monitor/Recorder with Front and Rear View Night Cameras PLCMDVR5
Mirror Mount Video Monitor/Recorder with Front and Rear View Night Cameras PLCMDVR5 www.pyleaudio.com Instruction Manual Installation and Connection: 1. Please disconnect your car battery. 2. In the contents
More informationPRODUCT NO.: PT-P1SD PRODUCT NAME: Digital SD Slide Projector
PRODUCT NO.: PRODUCT NME: Digital SD Slide Projector MJOR FETURES The one and only digital SD slide projector* - Built-in digital photo slide shows: direct SD card projection - Slide show features: transition
More informationDigital Active Indoor Antenna SRT ANT 10 ECO
Digital Active Indoor Antenna SRT ANT 10 ECO Picture similar User Manual Table of contents 1.0 INTRODUCTION 1 2.0 PACKAGE CONTENT 1 3.0 SAFETY NOTES 2 4.0 CONNECTING THE ANTENNA 2 1.0 INTRODUCTION Thank
More informationConnectors, Adapters, and Tools
MODEL NAME USE WITH: 213-CON Analog Output Connector 213 237-BAN-3 Triax to Banana Plug 7072, 7072-HV, 7172, 2001, DMMs 237-BNC-TRX 3-Lug Female Triax to Male BNC Connector with 237, 6517A, 7078-TRX cables
More informationCDI-S100 SERIAL INTERFACE CARD
CDI-S100 SERIAL INTERFACE CARD R R SERIAL INTERFACE MODULE MUSIC MUTE L L GAIN 0 LINE 5 LINE 6 db -10 + 10 MIC LEFT RIGHT FUSE 230V RATING 115V T100mA T200mA POW Installation Guide 2 CDI-S100 Installation
More informationRF Power Amplifier PA10W Owner s Manual SpinCore Technologies, Inc. http://www.spincore.com
RF Power Amplifier PA10W Owner s Manual SpinCore Technologies, Inc. http://www.spincore.com Congratulations and thank you for choosing a design from SpinCore Technologies, Inc. We appreciate your business!
More informationDisplayport Extender via 2 multimode fibers LC Duplex Connector Extends Displayport Link up to 200 meters
Description Displayport combines the audio and video through an interface. It supports high resolution displays and multiple displays with a single cable, and increases the efficiency and bandwidth of
More informationContents. Safety Warnings... 1
Contents Safety Warnings... 1 Unpacking the GQ600... 1 Introduction... 2 GQ600 Filter Characteristics... 2 1/3 Octave Centre Frequencies... 4 Front Panel Functions... 5 Rear Panel Functions... 6 Specifications...
More informationBMW CAR-PC MONITOR MODEL SPECIFICATION BMW3/5 SERIES. Model Name : BMW-100P Paper Version : Ver 1.0
BMW CAR-PC MONITOR MODEL SPECIFICATION BMW3/5 SERIES Model Name : BMW-100P Paper Version : Ver 1.0 INDEX Precacution Specification System Composition Product Outline Connector Pin Assignment Installaion
More informationPagePac PAGEPAL V-5335700
PagePac Issue 3 by PAGEPAL V-5335700 INTRODUCTION The PagePal unit interfaces most telephone systems (PBX, KTS, Centrex) to virtually any public address audio system. In addition, PagePal furnishes inputs
More informationIMMS-CCC. IMMS-CCC Hardwire Central Interface. Installation Instructions
IMMS-CCC IMMS-CCC Hardwire Central Interface Installation Instructions TABLE OF CONTENTS... Choose a Location... 1 Connections... 2 Operations... 3 Software Configuration... 4 Troubleshooting... 5 Loopback
More informationUser Guide FFFA001106. www.focusrite.com
User Guide FFFA001106 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Introduction...3 Features.................................................................... 3 Box Contents...3 System Requirements....4
More informationBerkeley Audio Design Alpha USB
QUICK USER GUIDE v1.2.2 Berkeley Audio Design Alpha USB The Alpha USB is an asynchronous High Speed USB to digital audio interface designed to provide the highest possible audio quality from computer audio
More informationPreliminary. Audio & Video Matrix Switchers featuring eight multi-format inputs and built-in scalers
Preliminary Audio & Video Matrix Switchers featuring eight multi-format inputs and built-in scalers and digital and video converted and distributed to digital outputs Product Overview Inputs: 8 and 8 /Component/S-video/
More informationIT-12M IT-12D Ver_2.0 INTERPRETATION SYSTEM. User s Manual
IT-12M IT-12D Ver_2.0 INTERPRETATION SYSTEM User s Manual Important Notice All the safety and instructions for operation and use of the equipment should be read carefully before the system is operated.
More informationPSP3. Stereo M/S preamplifier. User manual
PSP3 Stereo M/S preamplifier User manual AETA AUDIO 361, avenue du Général de Gaulle 92140 Clamart FRANCE Tél. +33 (0)1 41361212 Fax +33 (0)1 41361213 Telex 631178 Web : http://www.aetausa.com 55 000 020
More informationMODEL 2202IQ (1991-MSRP $549.00)
F O R T H E L O V E O F M U S I C F O R T H E L O V E O F M U S I C MODEL 2202IQ (1991-MSRP $549.00) OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION Congratulations on your decision to purchase a LINEAR
More informationInuktun Digital Video Recorder (DVR) Start Guide and Manual
Inuktun Digital Video Recorder (DVR) Start Guide and Manual Version 1.6 June 2012 CONTENTS INTRODUCTION... 3 What s Included...3 Supported Devices and Protocols...3 Connecting your DVR...4 Installation
More informationKit 106. 50 Watt Audio Amplifier
Kit 106 50 Watt Audio Amplifier T his kit is based on an amazing IC amplifier module from ST Electronics, the TDA7294 It is intended for use as a high quality audio class AB amplifier in hi-fi applications
More informationVX 2400 Dimmer User's Manual
TM VX 2400 Dimmer User's Manual 21-2119C Manual Revision 1.01 Software Version 1.0 10 March 1994 Table of Contents 1. General Description...3 1.1. Standard Features:...3 2. Installing Options...4 2.1.
More informationMTG-3901 ACO-3901 MODEL MASTER TIMING GENERATOR SYSTEM FEATURES PRODUCT DETAILS
MODEL MTG-3901 MASTER TIMING GENERATOR SYSTEM The MTG-3901 master timing generator system reaffirms Harris leadership in reference signal systems. The revolutionary architecture of the MTG-3901 master
More informationIn regard to calculating system power requirements, refer to DBK Basics located near the front of this manual.
DBK42 16-Slot 5B Signal Conditioning Module Overview 1 Hardware Setup 2 DBK42 Connection 2 DBK42 Configuration 2 5B Module Connection 2 Power Considerations 2 Terminal Block Connections 3 DaqBoard/2000
More informationF2400 FOM II Series Fiber Optic Modem Technical Manual
F2400 FOM II Series Fiber Optic Modem Technical Manual T1 Revision B Copyright April 2003 VERSITRON, Inc. 83 Albe Drive / Suite C Newark, DE 19702 www.versitron.com A030430283T PROPRIETARY DATA All data
More informationHDMI To CV S-Video Down Converter With HDMI Audio Decoding Operation Manual
HDMI To CV S-Video Down Converter With HDMI Audio Decoding Operation Manual Ambery Model No: SDV3 TABLE OF CONTENTS 1. Introduction... 1 2. Features... 1 3. Package Contents... 2 4. Operation Controls
More informationSPECIAL NOTICE. All references to NAT product part numbers (and associated images) are equivalent to AEM product part numbers.
SPECIAL NOTICE This product is now licensed to Anodyne Electronics Manufacturing (AEM) from Northern Airborne Technology (NAT). AEM is responsible for all matters related to this product, including sales,
More informationConverters for Desktop Product Line Catalog April 2011
C O N V E R T Converters for Desktop Product Line Catalog April 2011 B e c a u s e i t m a t t e r s. Table of Contents DWP 110V Power Supply 2 DWP-U Universal Power Supply 2 GEN10 HD/SD Sync Generator
More informationPRELIMINARY MANUAL STAGE COLOR 48. Preliminary User Guide. Official version will follow soon on: WWW.BRITEQ-LIGHTING.COM TABLE OF CONTENTS
STGE COO 48 Preliminary User Guide Official version will follow soon on: WWW.BITEQ-IGHTIG.COM TBE OF COTETS 1. Safety Instruction 2. Technical Specification 3. How To Set The Unit 4. How To Control The
More informationQUALITY AV PRODUCTS INMATE/INMATE USB PROFESSIONAL 19" MIXER. User Guide and Reference Manual
INMATE/INMATE USB PROFESSIONAL " MIXER User Guide and Reference Manual INTRODUCTION Welcome to the NEWHANK INMATE and INMATE USB professional " mixers series user manual. INMATE and INMATE USB both offer
More informationRadio Systems Millenium-D Digital Console
Radio Systems Millenium-D Digital Console Page 1 Radio Systems Millenium-D Digital Console Installation and Operation Manual Radio Systems Millenium Digital Broadcast Manual Part # MAN-MILLCOND For Console
More informationeela-audio EA916 Journalist Unit USB Audio module with Telephone Hybrid User manual
eela-audio EA916 Journalist Unit USB Audio module with Telephone Hybrid User manual EA Broadcast / Eela Audio, Het Riet 8 A, 5431NM Cuijk, The Netherlands http://www.eela-audio.com e-mail: sales@eela-audio.com
More information