Electronic Hinge Preparations S D I TECHNICAL DATA SERIES STEEL DOOR INSTITUTE DETROIT ROAD CLEVELAND, OHIO 44145
|
|
|
- Osborn Ryan
- 7 years ago
- Views:
Transcription
1 TECHNICAL DATA SERIES S D I Electronic Hinge Preparations 2016 Steel Door Institute STEEL DOOR INSTITUTE DETROIT ROAD CLEVELAND, OHIO 44145
2 Electronic Hinge Preparations 1 Purpose It is the intention of this document to furnish users of standard steel frames with practical information regarding an acceptable method for preparing frames for 4-1/2, 5 or continuous electric hinges. This document will allow frame manufacturers to provide frames prior to having knowledge of the specific electric hinge being used. 2 Scope The information contained herein pertains to frames manufactured in accordance with ANSI/SDI A The preparation as defined herein will accommodate the majority of electric hinges sold. It is the responsibility of the hardware specifier to assure compatible hinges are used. 3 Reference Documents ANSI/SDI A250.6 Recommended Practice for Hardware Reinforcings on Standard Steel Doors and Frames ANSI/SDI A250.8 SDI 100 Specifications for Standard Steel Doors & Frames ANSI/BHMA A156.7 Template Hinge Dimensions ANSI/BHMA A Hardware Preparation in Steel Doors and Steel Frames 4 Location The preparation for electric hinges is intended to be non-load bearing. Therefore it shall be located in the center hinge preparation on frames with 1-1/2 pair of hinges, and on the second hinge from the bottom on frames with 2 pair of hinges. 5 Hinge Reinforcement The hinge reinforcement shall comply with ANSI/SDI A250.6 and ANSI/SDI A250.8, and shall incorporate cutouts as shown in Figures 1, 2, 3 and 4. 6 Junction Box A junction box may be provided to facilitate wiring and connector installation. In addition, a hole shall be provided at the top and bottom of the junction box to facilitate conduit (see Figure 4). It is the responsibility of the electrical contractor to plug any unused holes. 1
3 Note 1: The hinge backset on the door varies by hollow metal door manufactures from 3/16 to 1/4 Note 2: The hinge backset on the frame varies by hollow metal frame manufactures from 5/16 to 3/8 Note 3: Extra holes may occur in the reinforcement for tooling and installation fixturing. Note 4: Some manufacturers offer a removable feature (e.g. - wire, shim, standoff projection) to allow conversion of a standard weight preparation for use with heavy weight hinge butt. Note 5: The most common mortise depths are in accordance with ANSI/BHMA A156.1 as follows: Standard Weight butt Heavy weight butt Figure 1 Preparation of 1 3/4 Steel Doors & Frames for 5 Full Mortise Electric Hinge 2
4 Note 1: The hinge backset on the door varies by hollow metal door manufactures from 3/16 to 1/4 Note 2: The hinge backset on the frame varies by hollow metal frame manufactures from 5/16 to 3/8 Note 3: Extra holes may occur in the reinforcement for tooling and installation fixturing. Note 4: Some manufacturers offer a removable feature (e.g. - wire, shim, standoff projection) to allow conversion of a standard weight preparation for use with heavy weight hinge butt. Note 5: The most common mortise depths are in accordance with ANSI/BHMA A156.1 as follows: Standard Weight butt Heavy weight butt Figure 2 Preparation of 1 3/4 Steel Doors & Frames for 4 1/2 Full Mortise Electric Hinge 3
5 Note 1: The hinge backset on the door varies by hollow metal door manufactures from 3/16 to 1/4 when hinge filler is in place. Note 2: The hinge backset on the frame varies by hollow metal frame manufactures from 5/16 to 3/8 Note 3: Extra holes may occur in the reinforcement for tooling and installation fixturing. Note 4: Some manufacturers offer a removable feature (e.g. - wire, shim, standoff projection) to allow conversion of a standard weight preparation for use with heavy weight hinge butt. Note 5: The most common mortise depths are in accordance with ANSI/BHMA A156.1 as follows: Standard Weight butt Heavy weight butt Figure 3 Preparation of 1 3/4 Steel Doors & Frames for 4 1/2 Full Mortise Electric Hinge Non-handed 4
6 Figure 4 Electrified Continuous Hinge Preparation on Standard Steel Frame 5
7 AVAILABLE PUBLICATIONS MEMBERS OF THE STEEL DOOR INSTITUTE Specifications ANSI/SDI A250.6 ANSI/SDI A250.8 SDI-108 SDI-118 SDI-128 SDI-129 Test Procedures Recommended Practice for Hardware Reinforcings on Standard Steel Doors and Frames SDI 100 Specifications for Standard Steel Doors & Frames Recommended Selection & Usage Guide for Standard Steel Doors Basic Fire Door, Fire Door Frame, Transom/Sidelight Frame, and Window Frame Requirements Guidelines for Acoustical Performance of Standard Steel Doors & Frames Hinge & Strike Spacing ANSI/SDI A250.3 Test Procedure & Acceptance Criteria for Factory Applied Finish Coatings for Steel Doors & Frames ANSI/SDI A250.4 Test Procedure & Acceptance Criteria for Physical Endurance for Steel Doors, Frames and Frame Anchors ANSI/SDI A Test Procedure & Acceptance Criteria for Prime Painted Steel Surfaces for Steel Doors & Frames ANSI/SDI A Testing and Rating of Severe Windstorm Resistant Components for Swinging Door Assemblies for Protection of Building Envelopes (Not applicable for FEMA 320/361 or ICC-500 Shelters) SDI-113 Standard Practice for Determining the Steady State Thermal Transmittance of Steel Door & Frame Assemblies SDI-131 Accelerated Physical Endurance Test Procedure for Steel Doors, Frames and Frame Anchors Construction Details ANSI/SDI A Recommended Erection Instructions for Steel Frames SDI-110 Standard Steel Doors & Frames for Modular Masonry Construction SDI-111 Recommended Details for Standard Details Steel Doors, Frames, Accessories and Related Components SDI-122 Installation Troubleshooting Guide for Standard Steel Doors & Frames Miscellaneous Documents SDI-112 SDI-117 SDI-124 SDI-127 SDI-130 SDI-134 Zinc-Coated (Galvanized/Galvannealed) Standard Steel Doors & Frames Manufacturing Tolerances for Standard Steel Doors & Frames Maintenance of Standard Steel Doors & Frames Industry Alert Series (A-L) Electrified Hinge Preparations Nomenclature for Standard Steel Doors & Steel Frames AUDIO-VISUAL PROGRAMS ALSO AVAILABLE Ceco An ASSA ABLOY Door Group Company 9159 Telecom Drive Milan, TN (731) Curries An ASSA ABLOY Door Group Company th Street P.O. Box 1648 Mason City, IA (641) Deansteel Manufacturing Co. 931 S. Flores Street San Antonio, TX (210) DOOR COMPONENTS INC Redwood Avenue Fontana, CA (909) HOLLOW METAL XPRESS 602 S. 65th Avenue Phoenix, AZ (623) Mesker Door, LLc 3440 Stanwood Boulevard Huntsville, AL (256) MPI 319 North Hills Road Corbin, KY (606) Pioneer Industries, Inc. 111 Kero Road Carlstadt, NJ (201) Republic Doors & Frames 155 Republic Drive McKenzie, TN (731) SMP An ASSA ABLOY Door Group Company 6089 Bristol Parkway, Suite 200 Culver City, CA (310) Steelcraft 9017 Blue Ash Road Cincinnati, OH (513) STEEL DOOR INSTITUTE 7/7/ DETROIT ROAD CLEVELAND, OHIO FAX
Test Procedure and Acceptance Criteria for Factory Applied Finish Coatings for Steel Doors and Frames
ANSI/SDI A250.3-2007 (R2011) Revision of ANSI A250.3-1999 Test Procedure and Acceptance Criteria for Factory Applied Finish Coatings for Steel Doors and Frames ANSI/SDI A250.3-2007 STEEL DOOR INSTITUTE
Fact File. Compilation of SDI Technical Documents and ANSI/SDI Standards and Test Methods. Updated August 2016
Fact File Compilation of SDI Technical Documents and ANSI/SDI Standards and Test Methods Updated August 2016 Please visit www.steeldoor.org for the latest version of the Fact File. Steel Door Institute
Standard Steel Doors, Frames, Accessories and Related Components
TECHNICAL DATA SERIES S D I 111-09 Recommended Details for Standard Steel Doors, Frames, Accessories and Related Components The information that follows represents the Standard Steel Door and Frame Industry's
122-15. Installation Troubleshooting Guide for Standard Steel Doors and Frames STEEL DOOR INSTITUTE 30200 DETROIT ROAD CLEVELAND, OHIO 44145 S D I
TECHNICAL DATA SERIES S D I 122-15 Installation Troubleshooting Guide for Standard Steel Doors and Frames 2016 Steel Door Institute STEEL DOOR INSTITUTE 30200 DETROIT ROAD CLEVELAND, OHIO 44145 This page
Recommended Erection Instructions for Steel Frames
ANSI/SDI A250.11-2012 Revision of ANSI/SDI A250.11-2001 Recommended Erection Instructions for Steel Frames ANSI/SDI A250.11-2012 SPONSOR Steel Door Institute Approved January 17, 2012 This page left intentionally
Doors and frames. Technical data manual 2015 rev. 8/17/15
Doors and frames Technical data manual 2015 rev. 8/17/15 Technical data manual Main table of contents NAVIGATE VIA: A) Rollover links in each TOC (each item below is a link), B) Bookmarks on the left,
Technical Data Honeycomb Door Leaf 8-1-99
8--99 8-/8 8-7/8 B 8-/4 A A Dim. A Leaf Width B ELEVATION F DESIGN Vertical edge seams mechanically interlocked Square hinge and lock edges 4-/ x.4 full mortise hinge prep Gov. 60/6 cyl lock prep...prefix
n Three 4 x 4 butt hinges per door - prevents wracking and assures smooth positive operation n Heavy duty 16 gauge steel frame
Weather Fin and bulb help keep bad weather outside and good air inside Windows: n Many light kits are available 1-LU 4 X 48 1-LE 16 X 16 1-LA 20 X 24 1-LI 20 X 24 1-B 22 X 36 1-LW 16 X 16 W/GRID 9-LB 22
ANSI A250.4 Test Procedure and Acceptance Criteria for Physical Endurance for Steel Doors, Frames and Frame Anchors
ANSI A250.4 Test Procedure and Acceptance Criteria for Physical Endurance for Steel Doors, Frames and Frame Anchors 1 Learning Session Description This training aid focuses on the revisions to ANSI A250.4-2011
BASIC FIRE DOOR REQUIREMENTS TECHNICAL DATA SHEET NO. 401
BASIC FIRE DOOR REQUIREMENTS SHEET NO. 401 Fire door openings are classified by their locations in the building. The location determines the length of exposure protection required, based on the potential
Steel Door Institute. Fire Rated Doors and Frames
Steel Door Institute Fire Rated Doors and Frames 1 1. Nomenclature and Overview 2. Fire Rated Frames 3. SDI 118 4. Fire Rated Doors 5. Fire Rated Hardware 6. Specialty Products Table of Contents 2 Fire
DIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS
DIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the contract, including general and supplementary conditions and other Division 1
FRAME PROFILE MASONRY METAL DOOR FRAME FLUSH MASONRY KD MITER CORNER JOINT. #8 Screw (MS002485) Required on all fire rated KD frames. Bend Tabs.
FRAME PROFILE MASONRY FLUSH MASONRY KD MITER CORNER JOINT Bend Tabs Head #8 Screw (MS002485) Required on all fire rated KD frames Corner Assembly 2" (50.8) Head Jamb Head Break Away Corner Clip Spot Welds
WHI 90-Minute Rated Veneered Door Frame Installation Instructions
No. 940-03-10 INSTALLATION INSTRUCTIONS 90 MINUTE RATED VENEERED DOOR FRAME DOOR REQUIREMENTS: Consult the door manufacturer to make sure that the doors are qualified for the hardware to be installed,
PDQ HINGE SUGGESTED ARCHITECTURAL SPECIFICATIONS METICULOUSLY MANUFACTURED, THE PDQ HINGE IS AVAILABLE IN 3 BASE METALS: SPECIFICATIONS HINGE SERIES
Commercial Hinges PDQ HINGES PDQ wants to be your total one source supplier of contract hardware materials. The introduction of a high quality PDQ hinge is another step in this direction. PDQ hinges are
HARDWARE LOCATIONS FOR HOLLOW METAL DOORS AND FRAMES
HOLLOW METAL MANUAL NAAMM STANDARD HMMA 831-11 8d NAAMM HMMA 831-11 METAL DOORS & FRAMES HARDWARE LOCATIONS FOR HOLLOW METAL DOORS AND FRAMES 8d NAAMM HMMA 831-11 METAL DOORS & FRAMES A Division of HOLLOW
9300BC SERIES Light Commercial Door Closer
Light Commercial Door Closer general information The 9300BC is a durable, economically priced door closer designed for commercial exterior and interior doors such as storefront and industrial applications.
Specifications for Standard Steel Doors and Frames (SDI-100)
Revision of ANSI/SDI A250.8-2003 Specifications for Standard Steel Doors and Frames (SDI-100) ANSI/SDI A250.8-2014 SPONSOR Steel Door Institute Approved June 2, 2014 This page left intentionally blank.
CONCEALED BEARING HINGES. StANLEy ARCHItECtuRAL HARDwARE
CONCEALED BEARING HINGES StANLEy ARCHItECtuRAL HARDwARE STANLEY ARCHITECTURAL HARDWARE TABLE OF CONTENTS Page Table of contents...2 Company history...2 5 knuckle concealed bearing design...3 Full mortise
Stainless Steel Continuous Hinges
Stainless Steel Continuous Hinges Hager heavy duty continuous hinges offer proven reliability that can stand up to the daily rigors of high-traffic, high-impact areas. They re designed and engineered to
PART 1 GENERAL 1.1 SECTION INCLUDES
J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including
Why Steel? Performance Study of Steel Doors and Frames Compared to Other Materials. September 2015. Sponsored by SDI, HMMA, CSDMA
Why Steel? Performance Study of Steel Doors and Frames Compared to Other Materials September 2015 Sponsored by SDI, HMMA, CSDMA CANADIAN STEEL DOOR MANUFACTURERS ASSOCIATION L'ASSOCIATION CANADIENNE DES
An ASSA ABLOY Group brand. 4800LN Series. Interconnected Locks
An ASSA ABLOY Group brand 4800LN Series Interconnected Locks performance meets style introduction The Yale 4800LN series interconnected locksets combine our key-in-lever locksets with the added safety
Eggers meticulously-crafted door frames are rivaled only by their beauty, quality and lasting performance. Turning nature s beauty into works of art
D O O R F R A M E S Eggers meticulously-crafted door frames are rivaled only by their beauty, quality and lasting performance. Turning nature s beauty into works of art D O O R F R A M E S Eggers Industries
DIVISION 00 - PROCUREMENT AND CONTRACTING REQUIREMENTS
DIVISION 00 - PROCUREMENT AND CONTRACTING REQUIREMENTS NOTICE TO BIDDERS BID FORM INSTRUCTIONS TO BIDDERS CONTRACTOR S BID FOR PUBLIC WORK - FORM 96 MINORITY AND WOMEN S BUSINESS ENTERPRISE PARTICIPATION
Advantage Pre-Assembled Doors & Frames
Technical Data Series Revised: 28 February, 2012 Page 1 of 23 Table of Contents Article I. SECTION 1.01 SPECIFICATIONS... 3 (a) Door Specifications... 3 (b) Frame Specifications... 3 (c) Door and Frame
FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES
FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke
Basic Fire Door Requirements
TECHNICAL DATA SERIES S D I 118-01 Basic Fire Door Requirements 2001 Steel Door Institute STEEL DOOR INSTITUTE 30200 DETROIT ROAD - CLEVELAND, OHIO 44145 Technical Data Series SDI 118-2001 Basic Fire Door
SECTION 14 20 10 - FREIGHT & PARKING GARAGE ELEVATORS PART I - GENERAL
SECTION 14 20 10 - FREIGHT & PARKING GARAGE PART I - GENERAL 1.1 SECTION INCLUDES [NOTE to AE: The following lists requirements that are specific to freight elevators. These requirements are in addition
Sub-Bid Contractor Update Statement. Tab A - Invitation for Bids. Tab B - Instructions to Bidders
INTRODUCTORY INFORMATION TABLE OF CONTENTS 00 0101 PROJECT TITLE PAGE PROCUREMENT REQUIREMENTS (PROJECT MANUAL) Tab A - Invitation for Bids Tab B - Instructions to Bidders Tab C Bid Form for General Bids
HMMA 830 HARDWARE SELECTION FOR HOLLOW METAL DOORS AND FRAMES HOLLOW METAL MANUAL -02 NAAMM STANDARD METAL DOORS & FRAMES NAAMM 01 NAAMM 01
HOLLOW METAL MANUAL NAAMM STANDARD HMMA 830-02 METAL S & FRAMES 8d NAAMM 01 02 HARDWARE SELECTION FOR HOLLOW METAL S AND FRAMES NAAMM 01 02 8d METAL S & FRAMES A Division of HOLLOW METAL MANUFACTURERS
THE RESOURCE FOR UNMATCHED SERVICE AND EXPERTISE.
THE RESOURCE FOR UNMATCHED SERVICE AND EXPERTISE. DOORWAY SOLUTIONS, a division of Colorado Doorways, Inc., specializes in sales, installation, and servicing of all commercial and institutional door openings.
City of San Diego, CWP Guidelines
PART 1 -- GENERAL SECTION 08520-1.1 WORK OF THIS SECTION City of San Diego, CWP Guidelines A. The WORK of this Section includes providing aluminum windows with frames, bracing, glazing attachments, screens,
Basic Technical Fundamentals of Builders Hardware Mortise, Bored and Auxiliary Locks
Mortise, Bored and Auxiliary Locks Copyright 2002, 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents Page SARGENT History...................................................
Basic Technical Fundamentals of Builders Hardware
Basic Technical Fundamentals of Builders Hardware Mortise Locks Bored Locks Auxiliary Locks Inside Cover (blank) Table of Contents SARGENT History...4 Basic Name of Products...5, 6 Doors (A Brief Review)...7
Nomenclature for: Standard Steel Doors and Frames
ANSI/SDI A250.7-1997 (R2002) Revision and Redesignation of ANSI/SDI A123.1-1989 Nomenclature for: Standard Steel Doors and Frames ANSI/SDI A250.7-1997 STEEL DOOR INSTITUTE SPONSOR Steel Door Institute
K. D. FRAME ASSEMBLY FOR CLOSED STEEL STUD WALLS...Ins 10. FRAME INSTALLATION DETAILS FOR CLOSED STEEL STUD WALLS...Ins 11
K. D. FRAME ASSEMBLY FOR MASONRY WALLS...........................Ins 2 FRAME INSTALLATION DETAILS FOR MASONRY WALLS......................Ins 3 INSTALLING EXISTING MASONRY WALL ANCHORS IN FRAME..................Ins
Sports and High Mast Lighting Poles Phone: (866) 474-7200 Fax: (817) 924-7049
Sports and High Mast Lighting Poles 4 High Mast Lighting Poles General American LitePole offers a raising and lowering system that allows for ease of maintaining the lighting system at ground level. Ideal
Wood Sound Retardant Door Hardware Information Bulletin
overly overly 574 West Otterman Street Greensburg, PA 15601 Toll Free: (800) 979-7300 Local: (724) 834-7300 Fax: (724) 830-2871 Email: overly@overly.com DOOR COMPANY Wood Sound Retardant Door Hardware
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word
DIVISION 08 70 00 HARDWARE FORMAT 1. Technical specifications content and numbering system shall be based on 2004 CSI MasterFormat.
FORMAT 1. Technical specifications content and numbering system shall be based on 2004 CSI MasterFormat. BASIS OF DESIGN 1. BGSU Design Standards shall not replace fully developed, project and market specific
SECTION 807 PUMP STATION REHABILITATION
SECTION 807 PUMP STATION REHABILITATION 807-1 DESCRIPTION: Rehabilitation of pump stations shall be defined as the cleaning, removal, repair and/or replacement of any and/or all components including but
SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 08332 COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Counter Fire Doors. 1.2
HARDWARE STANLEY ARCHITECTURAL HARDWARE
HARDWARE STANLEY ARCHITECTURAL HARDWARE STANLEY ARCHITECTURAL HARDWARE TABLE OF CONTENTS Page Company history...2 Wardrobe pivots...3, 4 Cabinet hinges... Cabinet pulls..., 6 Cabinet knobs...6 Cabinet
REDI-EXIT COMMERCIAL FIRE DOOR AND EXTERIOR DOOR KITS INSTALLATION GUIDELINES
REDI-EXIT COMMERCIAL FIRE DOOR AND EXTERIOR DOOR KITS INSTALLATION GUIDELINES Tools Required Tape Measure Hammer Slotted Screw Driver #2 & #3 Philips Screw Driver 3-4 Foot Level 12 Pry Bar Cold Chisel
Transfer Device Solutions
McKINNEY QC hinge transfers power from the power supply to the exit device Electromechanical exit device with ElectroLynx 3" cable, minimum, needed between electromechanical exit and QC hinge Contents
280+ Mortise Mounted Series Shear Locks Special Application Solution
280+ Mortise Mounted Series Shear Locks Power Plus control module overcomes gaps of up to 1/4" Low Temperature Operation 280+ TRD Locknetics provides the industry s most complete selection of electromagnetic
All work must conform to the National Electric Code, latest edition, and all other applicable codes and regulations.
DIVISION 16 ELECTRICAL SECTION 16100 - ELECTRICAL PART 1 - GENERAL SCOPE All electrical work as shown on the drawings and as necessary to provide a complete electrical system. Include primary service,
TECHNICAL SPECIFICATIONS & SPECIAL CONDITIONS OF CONTRACT FOR ELECTRICAL WORKS CHAPTER 1 SPECIAL CONDITIONS OF CONTRACT
TECHNICAL SPECIFICATIONS & SPECIAL CONDITIONS OF CONTRACT FOR ELECTRICAL WORKS CHAPTER 1 SPECIAL CONDITIONS OF CONTRACT 1.1 General 1.1.1 These Special Conditions of Contract supplement the General Instructions.
DIVISION 08 70 00 HARDWARE FORMAT 1. Technical specifications content and numbering system shall be based on 2004 CSI MasterFormat.
FORMAT 1. Technical specifications content and numbering system shall be based on 2004 CSI MasterFormat. BASIS OF DESIGN 1. APSU design standards shall not replace fully developed, project and market specific
Data Center Security. Perimeter and Door Opening Solutions
Data Center Security Perimeter and Door Opening Solutions Who We Are ASSA ABLOY is the global leader in door opening solutions, representing leading door and hardware brands. Our goal is to help facilities
Installation S D I 122-99 TECHNICAL DATA SERIES. and Troubleshooting Guide. for Standard Steel Doors and Frames STEEL DOOR INSTITUTE
TECHNICAL DATA SERIES S D I 122-99 Installation and Troubleshooting Guide for Standard Steel Doors and Frames STEEL DOOR INSTITUTE 30200 DETROIT ROAD - CLEVELAND, OHIO 44145 Table of Contents Improper
Plaisance 50. Windows and doors. Sapa Building System
Plaisance 50 Windows and doors Sapa Building System Plaisance 50 is a non-thermally broken system for aluminium windows and doors with a building depth. The system offers a wide range of inward and outward
C. Codes and References: Comply with the version year adopted by the Authority Having Jurisdiction.
SECTION 081216 - INTERIOR ALUMINUM DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
09/07/07 GLASSFIBER REINFORCED CEMENT (GRC) C. S. I. Spec 03500 Master Spec. 03 49 00 Page 1
C. S. I. Spec 03500 Page 1 PART 1 - GENERAL 1.01 SUMMARY:.01 Provide special glassfiber reinforced cement (GRC) shapes in accordance with the requirements of the contract documents..02 The installing contractor
Narrow stile lock 1314
3 2 4 6 6 1 3 2 4 4 5 3 2 4 3 5.... ( (. ). ) 11 12 5 3 5 4 8 1 6 20 8.5 6.5 19 Backset 15 3 5 2 1 5 2 5 5 0 8 9 2 8 1 1 21-1mm 12 8 24 1 6 8 1 ( 9 2 5 ) ) ). ) Narrow stile lock 1314 CE EN 12209 2 4 5
ENGINEERING SPECIFICATION FIBERGRATE MOLDED GRATING. January 24, 2014 06610-1
ENGINEERING SPECIFICATION FIBERGRATE MOLDED GRATING January 24, 2014 06610-1 SECTION 06610 FIBERGLASS REINFORCED PLASTICS (FRP) FABRICATIONS MOLDED GRATING PART 1 - GENERAL 1.1 SCOPE OF WORK A. The CONTRACTOR
ABLOY EXIT. Functional and technical descriptions Single and double leaf doors. An ASSA ABLOY Group brand
SSFN 014/2 2 ABLOY EXIT Functional and technical descriptions Single and double leaf doors An ASSA ABLOY Group brand ABLOY EXIT - EXIT PRODUCTS It is time to take the exit safety standards to a new level.
PROJECT TITLE : 2-STOREY RESIDENCE LOCATION : ALONG DAANG HARI,MOLINO.BACOOR,CAVITE OWNER : CUEVASVILLE REALTY
PROJECT TITLE : 2-STOREY RESIDENCE LOCATION : ALONG DAANG HARI,MOLINO.BACOOR,CAVITE OWNER : CUEVASVILLE REALTY GENERAL SPECIFICATIONS These specifications are intended to cover the construction of the
ABLOY DOOR AUTOMATICS Easy access for all types of swing doors
ABLOY DOOR AUTOMATICS Easy access for all types of swing doors Automatic door operators bring additional convenience in situations where the doors opening manually would be inconvenient or laborious. Recommended
DE Frame with C Series Sidelight
TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder
Automatic Door Selection Guide
Automatic Door Selection Guide AAADM 1300 Sumner Avenue Cleveland, OH 44115 P: 216-241-7333 F: 216-241-0105 aaadm@aaadm.com Automatic Door Selection Guide General: The members of AAADM manufacture an assortment
MEANS OF EXIT / ESCAPE / EGRESS SELF INSPECTION CHECKLIST
OPTIONAL INFORMATION Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: MEANS OF EXIT / ESCAPE / EGRESS Guidelines: This checklist covers some of the regulations
DOORS HOLLOW METAL MANUAL NAAMM STANDARD NAAMM HMMA 810-09 METAL DOORS & FRAMES METAL. A Division of
HOLLOW METAL MANUAL NAAMM STANDARD HMMA 810-09 8d NAAMM HMMA 810-09 METAL DOORS & FRAMES HOLLOW METAL DOORS 8d NAAMM HMMA 810-09 METAL DOORS & FRAMES A Division of HOLLOW METAL MANUFACTURERS A S S O C
RTS88. Overhead Concealed Door Closer
RTS88 Overhead Concealed Door Closer RTS88 OVERHEAD CONCEALED CLOSER DORMA RTS88 OVERHEAD CONCEALED DOOR CLOSER Invisible door control Dependable and easy to install Architects are often challenged to
BILL OF QUANTITIES Part No.: Part Description
Page 1 of 5 A. REMOVAL OF STRUCTURES 801 Demolition of Existing Structure lot 1 in words in words B. MASONRY WORKS 506(1)a Masonry Units (CHB) sq.m. 58.80 in words in words C. FABRICATED MATERIALS & HARDWARE
Door Hardware Lock Specifications
Door Hardware Lock Specifications Directory Lock Type Page Exterior Mortise Lock Specifications... 2 2.5 Backset Mortise Locks Specification... 3 2.5 Backset Mortise Lock Functions (6301, 6310, 6315, 6318,
Auxiliary hardware & general information. Exit devices
Auxiliary hardware & general information Exit devices Introduction Since pioneering the first exit device in 1908, Von Duprin life safety products have provided unparalleled quality, performance and flexibility
Electrified Products TABLE OF CONTENTS. Power Transfers...12 Pressure Sense Bars...12 Proximity Cards & Keys... 4
TABLE OF CONTENTS A Adjustable Angle Bracket (294/2942)... 6 Angle Brackets (2950 Series)... 9 Armature Mounting Plates (2950 Series)... 7 C Coordinator Mounting Bracket (2950 Series)... 7 Concealed Magnetic
Mechanical Digital DX Locks
ASSA ABLOY, the global leader in door opening solutions Contents Mechanical Digital DX Locks Overview 1 002 Digital DX Deadlatch 2 530 Digital DX Entrance Set 3 3572 Digital DX Mortice Locksets 4 3582,
Avantis 75. Windows & Doors. Sapa Building System
Avantis 75 Windows & Doors Sapa Building System Avantis 75 is a thermally broken three-chamber window and door system, which sets the highest standards of thermal insulation and stability. Avantis 75
Security steel door dw 52-1 Teckentrup DF WK 2 optionally with glazing/ventilation grille
Security steel door dw 52-1 Teckentrup DF WK 2 optionally with glazing/ventilation grille Text example Compile and tender according to requirements. Please refer to technical data below for respective
Steel Door Frame Installation in Steel Stud Construction
Steel Door Frame Installation in Steel Stud Construction For use with the Steel Door Institute (SDI) video How to Install a Steel Door Frames in Steel Stud Construction This manual gives you step-by-step
Fire-rated Aluminum Doors
Fire-rated Aluminum Doors Langebjergvænget 13 ALUFLAM has pioneered the innovative solution to what was long considered an impossible dream (and a barrier to truly beautiful commercial architectural design),
Subject: DKS Steel Door and Frames Systems, Inc., ITS / Warnock Hersey Procedural Specification, Certification, and Inspection.
DKS Customers Interested Parties State and Local Authorities Subject: DKS Steel Door and Frames Systems, Inc., ITS / Warnock Hersey Procedural Specification, Certification, and Inspection. All DKS products
A D D E N D U M # 3 QUESTIONS FROM BIDDERS: DATE: November 5, 2012. All Bidders. Jenne dos Santos, CBI Consulting Inc. City of Chelsea, MA
Page 1 of 10, Addendum No. 3 Temporary Garage Structure City of Chelsea, MA November 5, 2012 CBI Job No.: 12055-A A D D E N D U M # 3 DATE: November 5, 2012 TO: FROM: PROJECT: All Bidders Jenne dos Santos,
HMMA 810 HOLLOW METAL DOORS HOLLOW METAL MANUAL -87 NAAMM STANDARD FOURTH EDITION METAL DOORS & FRAMES NAAMM 2 NAAMM 2 METAL DOORS & FRAMES
HOLLOW METAL MANUAL NAAMM STANDARD HMMA 810-87 8d METAL DOORS & FRAMES NAAMM 2 87 HOLLOW METAL HOLLOW METAL DOORS FOURTH EDITION NAAMM 2 87 8d METAL DOORS & FRAMES A Division of NATIONAL ASSOCIATION OF
Plaisance 24. Sliding Systems. Sapa Building System
Plaisance 24 Sliding Systems Sapa Building System Plaisance 24 is Sapa s noninsulated sliding system for windows and doors. Available as one-, two-, three- and fourrail solution. Among its features, there
SECTION 6. Glass Storefront Doors:
SECTION 6 Glass Storefront Doors: Table of Contents 3070 Storefront Door System Description & Dimensions 6070 Storefront Door System Description & Dimensions Door Leaf Detail Optional 10 Bottom Rail Detail
EMF/EMR. Holder/Release Devices with Integral Door Closers
EMF/EMR Holder/Release Devices with Integral Door Closers EMR TECHNICAL DETAILS DORMA EMR SERIESHOLDER/RELEASE DEVICE The DORMA EMR Series holder/ release device incorporates a photoelectric detector and
Cluster Box Units. (CBU s) 3300 Series CBU Door Sizes. Fully Integrated Parcel Lockers CLUSTER BOX UNITS FRONT LOADING. continued on pages 7-11
Cluster Box Units (CBU s) continued on pages 7-11 CLUSTER BOX UNITS FRONT LOADING Made of heavy duty aluminum and stainless steel hardware, Salsbury 3300 series U.S.P.S. approved Cluster Box Units (CBU
System components portfolio overview. Power supplies, electromagnetic locks, electric strikes and system accessories
System components portfolio overview Power supplies, electromagnetic locks, electric strikes and system accessories Our comprehensive commercial portfolio includes everything you need to hang, protect,
HES & Folger Adam Electric Strikes & Accessories CANADIAN PRICELIST. Effective Date: Apirl 4, 2016
2016 CANADIAN PRICELIST HES & Folger Adam Electric Strikes & Accessories Effective Date: Apirl 4, 2016 About HES and Folger Adam About Headquartered in Phoenix, Arizona, Hanchett Entry Systems, Inc. (HES),
Air-Conditioning, Heating, and Refrigeration Institute. Sheet Metal and Air-Conditioning Contractors National Association
Air-Conditioning, Heating, and Refrigeration Institute Sheet Metal and Air-Conditioning Contractors National Association GUIDELINE B-1997 ACKNOWLEDGEMENT These guidelines for Roof Mounted Outdoor Air-
Patio Covers / Carports
Patio Covers / Carports Building Guides for Homeowners Why Do I need a Permit? D I D Y O U K N O W? As owner-builder you are the responsible party of record on such a permit. If your work is being performed
INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks
Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 techsupport@securitron.com in door opening solutions INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate
Drum Dispensing Stations
Drum Dispensing Stations O Safely Dispense from 55 Gallon Drums over a Spill Compliant Sump. 1-2-and 4 drum models available Drums are securely held on racks by galvanized positioners Sump and frame constructed
Quality Building Products for over 50 Years
Light Commercial Quality Building Products for over 50 Years Harvey Building Products is a leading manufacturer and distributor of high quality building products. We manufacture a complete line of superior
ST. MONICA FOOD PANTRY HOUSTON, TEXAS
PROJECT MANUAL FOR ST. MONICA FOOD PANTRY HOUSTON, TEXAS OWNER: ST. MONICA CATHOLIC CHURCH 8421 W. MONTGOMERY ROAD HOUSTON, TEXAS 77088 ARCHITECT: C SIX ARCHITECTURE, LLC 4606 F.M. 1960 WEST, STE 400 HOUSTON,
SECTION 32 31 13 CHAIN LINK FENCES AND GATES
PART 1 GENERAL 1.1 DESCRIPTION SECTION 32 31 13 CHAIN LINK FENCES AND GATES SPEC WRITER NOTES: 1. Delete or add information between //---// and any other items applicable to project. Cover any item added
7200 series Electromechanical Closer/Holder
7200 series Electromechanical Closer/Holder introduction The 7200 Series Electromechanical Closer/Holders combine the functions of an electromechanical door holder with the 7700 series door closer. The
SECTION 08740 ELECTRO-MECHANICAL HARDWARE
SECTION 08740 ELECTRO-MECHANICAL HARDWARE PART 1 - GENERAL 1.1 SUMMARY: A. Section Includes: 1. Items known commercially as electro-mechanical hardware, required for special applications at limited doors.
SECTION 03400 PRECAST CONCRETE STRUCTURES
SECTION 03400 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for precast concrete structures, including fabrication and erection. 1.02 REFERENCE STANDARDS A. American Society for
Glass. Pre-Assembled Glass Entry Doors. In Stock Models Available! 1-800-486-8415
Glass Store Front Doors 1-800-486-8415 www.glassstorefrontdoors.com Pre-Assembled Glass Entry Doors Commercial Glass Store Front Doors Pre-Assembled and Ready for Quick Install In Stock Models Available!
Specifications 7 Line Cylindrical Lever Locks
7 Line Bored Lever Lock Copyright 2003-2015, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Specifications Table of Contents Windstorm Certifications...1 Features, Benefits
MRI RF SHIELDING DESIGN
MRI RF SHIELDING DESIGN Nelco s MRI RF Shielding is specifically designed for the MRI industry. Our engineers have developed a shielded enclosure made entirely of nonmagnetic materials that is unsurpassed
Fabrication Illustration Part No. Description Door Frame. P092 Mortised Butt Hinge P092D P092F (includes P2092 $ 48 $ 21 frame/door reinforcing)
Custom Blank Entrances - Applied Hardware & Preps - Tubelite Standard Hardware Butt Hinges Pivots C2 Page 1 P092 Mortised Butt Hinge P092D P092F (includes P2092 $ 48 $ 21 frame/door reinforcing) P795S
Confort 26. Sliding Systems. Sapa Building System
Confort 26 Sliding Systems Sapa Building System Confort 26 is Sapa s thermally insulated sliding system for windows and doors. Available as two- and three-rail solution. Among its features, there are
2.02. Specifications. General. Products. Execution. Offset Pivots P-694 Top and Bottom Pivots
2.02 Standard Specifications General Entrances Description Furnish all necessary materials, labor and equipment for the complete installation of aluminum entrance doors, door frames and hardware as shown
Guidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)