1070 SLIDING MALL FRONT

Size: px
Start display at page:

Download "1070 SLIDING MALL FRONT"

Transcription

1 70 SLIDING MALL FRONT INDEX 1 PICTORIAL VIEW ELEVATION / VERTICAL SECTION DETAILS HORIZONTAL SECTION DETAILS STACK AREA LAYOUT PANEL SIZE LIMITS PRODUCT LIMITATIONS, GENERAL INFORMATION HARDWARE SPECIFICATIONS LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOWS, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversions figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI) units are found in these details: m - meter cm - centimeter mm - millimeter s - second Pa - pascal MPa - megapascal Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement. KAWNEER COMPANY, INC. 200

2

3 70 SLIDING MALL FRONT PICTORIAL VIEW Top guide pin Center pivoted swing entrance doors Adjustable sealed bearing floor castors Single solid aluminum floor track KAWNEER COMPANY, INC. 200

4 70 SLIDING MALL FRONT ELEVATION / VERTICAL SECTION DETAILS SCALE 1/ FULL SIZE *NOTE: OPTIONAL WEATHERING TRIM CAN BE USED AT THE INTERIOR WITH STRAIGHT PANEL RUNS ONLY. 2 1 MAXIMUM ALLOWABLE STRUCTURAL DEFLECTION 1/" (6.). 6 ENTRANCES CANNOT BE BUILT WITHOUT TRANSOM LITES. TRANSOM LITE MUST BE A MINIMUM OF 12" (05) HIGH. PROPER SUPPORT MUST BE PROVIDED FOR FLOOR AND HEAD TRACK INCLUDING THE STACK AREA /" (22.2) " Min. 1/" (76.2 Min.) (6.) 1/2" 5-2/2" DLO " DLO " 1-1/" (12.7) (150.0) (76.2) (76.2) (2.6) 1 RECESSED HEAD APPLICATION HH02 INTERMEDIATE HORIZONTAL HI01 5 PANEL BOTTOM RAIL (WITH EXTERIOR DRAINING TRACK) HS01 (11.) " (76.2) 60-1 Drain Tube 1/2" (12.7) 5/" (15.) * NOTE 1 (ALTERNATE) SURFACE HEAD APPLICATION HH01 2 TRANSOM BAR DP02 SWING DOOR BOTTOM RAIL DP05 1 1/" (2.6) 1/" (6.) " (76.2) " (76.2) 2-1/" (57.2) -7/" (.) 1/2" (12.7) 1-1/2" Min (.1 Min.) 5/16" (7.) (11.) 1/2" (12.7) 5/" (15.) Drain connections to 60-1 to be by others 1" (25.) to 1-1/" (1.) O.D. drain tubing recommended every 15' (.572 meters) and 5-1/2" Min. at each end. (1.7 Min.) KAWNEER COMPANY, INC. 200 Overall panel height Door opening height DLO

5 70 SLIDING MALL FRONT HORIZONTAL SECTION DETAILS 5 NOTE: Cylinder locks shown for illustration only. (Specify exact location) Maximum sidelight width is 2'-0" (6) -1/" (2.6) 1-/" (.5) Entrances are 6'-0" x 7'-0" (12 x 21) pair of doors, Kawneer concealed overhead closer only. -1/" (7.) 7/" (22.2) of track Lock (11.) (11.) -/" (120.6) 2-1/2" (6.5) 1-1/2" (.1) 6 LOCK JAMB VJ01 1-/" (.5) 7 SWING DOOR JAMB DP11 DOOR JAMB / MEETING STILES DP07 1-/" (.5) -1/" (7.) 6-1/" (15.) -1/" (7.) -1/" (2.6) (11.) (11.) of track MEETING STILES MEETING MULLIONS JAMB Bumper -/" (120.6) VI01 VI02 VI0-1/" (7.) 6-1/" (15.) -1/" (7.) 1-1/2" (.1) Glass pocket at transom (OPTIONAL CONDITIONS WHEN TWO ENTRANCE PANELS MEET) MEETING MULLIONS PD0 KAWNEER COMPANY, INC. 200

6 6 70 SLIDING MALL FRONT STACK AREA LAYOUT Basic considerations for door detailing sliding wall arrangements and stacking sequence. 1. Caster spacing for 6'-0" entrances with sidelite may not vary from standard dimension of 7-1/" (17.6). 2. Caster spacing for 6'-0" entrances without sidelite may not vary from standard dimensions of 75-1/16" (6.6). Minimum locations of caster center line from end of bottom horizontal is " (76.2) actual location depends on entrance unit wheel spacing and non-entrance panel detailed width.. 70 stacking is only as shown. Pocket dimensions depend on panel width and position in stack. 5. Parallel stacking only. Note: Size and location of chase in floor cannot usually be determined until job is detailed. -/" (120.6) Varies 7-1/" (17.6) Note # Note #1 Clear opening 5-1/2" (1.2) min. width track chase required to install track. Pocket area must accommodate extension of entrance sidelight 7-1/" (17.6) Note # Note #1 Clear opening Locate stack so entrance sidelight does not project into clear opening. 7-1/" (17.6) Note #1 Note # Clear opening When entrance is last panel into stack, caster spacing of non-entrance panels may be set greater than entrance caster spacing. 75-1/16" (6.6) Clear opening Note # Note #2 Locate stack so that panels do not project into clear opening. 75-1/16" (6.6) Note #2 Note # Clear opening When entrance is last panel into stack, caster spacing of non-entrance panels may be set greater than entrance caster spacing. KAWNEER COMPANY, INC. 200

7 70 SLIDING MALL FRONTS SIZE LIMITS 7 PANEL SIZE LIMITATIONS Mullions are designed for L/175 deflection ratio. These curves are for mullions with horizontals and are based on precise engineering calculations for stress, deflection and buckling. Allowable windload stress for ALUMINUM 12,2 P.S.I. ( MPa). Charted curves, in all cases are for the limiting value. For special situations not covered by these curves, contact your Kawneer representative for additional information. (Note: Calculations are in accordance with the National Building Code of Canada based on CAN-S157 "Strength Design in Aluminum".) EXTERIOR APPLICATION WITH ENTRANCES EXTERIOR APPLICATION WITHOUT ENTRANCES I =.17 in (.2 x 6mm ) I = 6.55 in (2.7 x 6mm ) S =.0 in (6.6 x mm ) S = 2.0 in (.76 x mm ) HEIGHT IN FEET WIDTH IN METERS C D E B WIDTH IN FEET Minimum panel width with entrances 6'-6 1/ " (1) Minimum panel height with entrances '-0" (2) Maximum panel width with entrances '-1/ " (26)* Maximum panel height with entrances 12'-0" (65)* NOTE: * ONLY WITH A DESIGN LOAD OF 15 p.s.f. (720 Pa.) CAN A PANEL BE THE MAXIMUM WIDTH AND HEIGHT. FOR HIGHER DESIGN LOADS, THE PANEL MUST BE LIMITED TO THE CURVES B, C, D, AND E IN THE GRAPH ABOVE. HEIGHT IN METERS A = 15 p.s.f. (0.72 kpa.) B = 20 p.s.f. (0.6 kpa.) C = 25 p.s.f. (1.20 kpa.) D = 0 p.s.f. (1. kpa.) E = 5 p.s.f. (1.6 kpa.) HEIGHT IN FEET WIDTH IN METERS MINIMUM WIDTH E A B C D MAXIMUM HEIGHT WITHOUT HORIZONTALS WIDTH IN FEET HEIGHT IN METERS INTERIOR APPLICATION ONLY HEIGHT IN FEET WIDTH IN METERS MINIMUM WIDTH MAXIMUM HEIGHT WITHOUT HORIZONTALS HEIGHT IN METERS WIDTH IN FEET KAWNEER COMPANY, INC. 200

8 70 SLIDING MALL FRONT PRODUCT LIMITATONS and GENERAL INFORMATION STACK AREA LAYOUT (For units with entrance doors.) / " (120.7) NOTE: IF POCKET ENCLOSURE IS USED THEN ACCESS TO POCKET MUST BE PROVIDED. "W" 7" (177.) 7/ " (12.) " (12.) /" (120.6) 7 / PARALLEL STAGGERED STACK Minimum "L" = Panel width + " (25) + {21/ " (57) x (number of panels - 2)}. Minimum "W" = 11 11/ 16" (26.) + { 7/ " (12.) x (number of panels - 1)}. NOTE: STACK AREA MUST HAVE ADEQUATE SUPPORT FOR THE PANEL WEIGHT. 21/ " 5 1/ " 2 / " (6.) (Min.) (57.2) (1.) "L" SLIDING PANELS (LOCKS) - ADAMS RITE MS-17 Floor bolt HARDWARE STANDARDS ENTRANCE DOORS - Architect's Classic Push/Pulls - ADAMS RITE MS-150A deadlock - Top and bottom flush bolts - Threshold - "HUSKY II" Concealed overhead closers 1. Swing doors in "70" Panels are restricted to: (A) 6' x 7' (12. x 21.6) Pairs of Kawneer doors with Standard MS Locks Only. (B) Center Hung with Kawneer HUSKY-II Concealed Overhead Closer Only. Double Acting can be made Single Acting by use of Door Stop on Transom Bar. (C) The following Push-Pull Hardware Styles are the Only ones Applicable with the "70" Swing Doors: (a) Architect's Classic Style CO-/CP (b) Architect's Classic Style CO-12/CP (c) Architect's Classic Style CP/CP (d) Architect's Classic Style CO-/CO- (e) Architect's Classic Style CO-12/CO Total Height of Panels with Swing Doors MUST BE Minimum of '-0" (2.) which is a 7'-0" (21.6) Pair of Doors plus a Transom Height of 1'-0" (0.) MINIMUM.. Parallel STAGGERED STACKING Only.. Drain Pipes from Drain NOT By Kawneer. 5. Sidelite to Swing Doors - MAXIMUM width 2'-0" (60.6). 6. "70" Will Accept Flush Glazed 1/" (6.) Glass or panel ONLY. PRODUCT LIMITATIONS General Description: The "70" sliding front consists of single trackage with parallel stacking of exterior and interior applications. Because the "70" incorporates swing entrances, it is ideally suited for the following monumental and commercial applications: - Entrances to shopping malls - Large movable walls - Movable storefronts - Automobile showrooms - Seasonal open front merchandising GENERAL INFORMATION KAWNEER COMPANY, INC. 200

9 70 SLIDING MALL FRONT HARDWARE 70 HARDWARE INBOARD HEAD GUIDE RECESSED HEAD GUIDE RECESSED CASTER INBOARD CASTER MS 17 LOCK SWINGING ENTRANCE DOOR PUSH/PULL HARDWARE REFER TO HARDWARE SECTION FOR ADDITIONAL INFORMATION. 2-/" (6.) 2-/" (6.) *-5/16" (1125.) " (22.6) *-5/16" (1125.) 12" (0.) *-5/16" (1125.) CP PUSH BAR CO- PULL CO-12 PULL NOTE: * DIMENSIONS ARE FROM BOTTOM OF DOOR TO ATTACHMENT POINT. 2-/" (6.) 2-/" (6.) " (22.6) *-5/16" (1125.) CO-/CP PUSH/PULL 12" (0.) *-5/16" (1125.) CO-12/CP PUSH/PULL Finishes: Architect's Classic Push/Pull Hardware are available in the following finishes: #1 Clear, #2 Black and #0 Dark Bronze Anodized. # Bronze - US B oil rubbed, 5 Stainless Steel - US2 polished, #6 Stainless Steel - US2D dull and #7 Bright Brass (PVD) - US. KAWNEER COMPANY, INC. 200

1040 Sliding Mall Front

1040 Sliding Mall Front JULY, 0 EC -0 00 Sliding Mall Front INDEX ELEVATIONS/VERTICAL SECTION DETAILS... HORIZONTAL SECTION DETAILS... EGRESS DOOR... - STACK AREA LAYOUT... - SIZE LIMITATIONS... HARDWARE...0 Kawneer Company,

More information

Features. Optional Features

Features. Optional Features AUGUST, 2006 190/350/500 STANDARD ENTRANCES 1 FEATURES Features 190 narrow stile has 2-1/8" vertical stile, 2-1/4" top and 3-7/8" bottom rail 350 medium stile has 3-1/2" vertical stile, 3-1/2" top and

More information

190/350/500 Standard Entrances

190/350/500 Standard Entrances AUGUST, 2015 FEATURES 1 Features 190 narrow stile has 2-1/8" (54) vertical stile, 2-1/4" (57.2) top and 3-7/8" (98.4) bottom rail 350 medium stile has 3-1/2" (88.9) vertical stile, 3-1/2" (88.9) top and

More information

2.02. Specifications. General. Products. Execution. Offset Pivots P-694 Top and Bottom Pivots

2.02. Specifications. General. Products. Execution. Offset Pivots P-694 Top and Bottom Pivots 2.02 Standard Specifications General Entrances Description Furnish all necessary materials, labor and equipment for the complete installation of aluminum entrance doors, door frames and hardware as shown

More information

ENTRANCES AND FRAMES INSTALLATION MANUAL

ENTRANCES AND FRAMES INSTALLATION MANUAL ENTRANCES AND FRAMES INSTALLATION MANUAL 11/18/13 Tubelite Inc. 0 of 31 11/18/13 Tubelite Inc. 1 of 31 INSTALLATION NOTES Allow 1/4" minimum shim and sealant space at sides and top of door frame. Door

More information

FINISHES DESIGNATIONS... 2 PAINTED FINISHES...3, 4 STANDARD HARDWARE FINISH OFFERINGS...5, 6

FINISHES DESIGNATIONS... 2 PAINTED FINISHES...3, 4 STANDARD HARDWARE FINISH OFFERINGS...5, 6 FEBRUARY, 2014 FINISHES INDEX 1 FINISHES DESIGNATIONS... 2 PAINTED FINISHES...3, 4 STANDARD HARDWARE FINISH OFFERINGS...5, 6 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE,

More information

CLEAR-DIVISIONS VARIOTEC TRIMLESS

CLEAR-DIVISIONS VARIOTEC TRIMLESS CLEAR-DIVISIONS VARIOTEC TRIMLESS Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS VARIOTEC TRIMLESS moveable glass wall system.

More information

Automatic Door Selection Guide

Automatic Door Selection Guide Automatic Door Selection Guide AAADM 1300 Sumner Avenue Cleveland, OH 44115 P: 216-241-7333 F: 216-241-0105 aaadm@aaadm.com Automatic Door Selection Guide General: The members of AAADM manufacture an assortment

More information

SECTION 6. Glass Storefront Doors:

SECTION 6. Glass Storefront Doors: SECTION 6 Glass Storefront Doors: Table of Contents 3070 Storefront Door System Description & Dimensions 6070 Storefront Door System Description & Dimensions Door Leaf Detail Optional 10 Bottom Rail Detail

More information

GLASS WALL POCKET DOORS

GLASS WALL POCKET DOORS GLASS WALL POCKET DOORS KWIK-WALL... One Source for Wall Systems. KWIK-WALL s Pocket Doors for glass wall systems bring you the clear solution to your space division requirements. The beauty and elegance

More information

Thermal Block Entrance Installation Manual. Thermal Entrances. Installation Instructions. 05/21/14 Tubelite Inc. Page 0 of 20

Thermal Block Entrance Installation Manual. Thermal Entrances. Installation Instructions. 05/21/14 Tubelite Inc. Page 0 of 20 Thermal Entrances Installation Instructions 2010 05/21/14 Tubelite Inc. Page 0 of 20 TABLE OF CONTENTS INSTALLATION NOTES........................................ 2 PARTS LIST........................................

More information

CLEAR-DIVISIONS CENTERFOLD

CLEAR-DIVISIONS CENTERFOLD CLEAR-DIVISIONS CENTERFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS CENTERFOLD moveable The yellow highlighted areas in

More information

CLEAR-DIVISIONS VARIOFOLD

CLEAR-DIVISIONS VARIOFOLD CLEAR-DIVISIONS VARIOFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS VARIOFOLD moveable The yellow highlighted areas in the

More information

HMMA 810 HOLLOW METAL DOORS HOLLOW METAL MANUAL -87 NAAMM STANDARD FOURTH EDITION METAL DOORS & FRAMES NAAMM 2 NAAMM 2 METAL DOORS & FRAMES

HMMA 810 HOLLOW METAL DOORS HOLLOW METAL MANUAL -87 NAAMM STANDARD FOURTH EDITION METAL DOORS & FRAMES NAAMM 2 NAAMM 2 METAL DOORS & FRAMES HOLLOW METAL MANUAL NAAMM STANDARD HMMA 810-87 8d METAL DOORS & FRAMES NAAMM 2 87 HOLLOW METAL HOLLOW METAL DOORS FOURTH EDITION NAAMM 2 87 8d METAL DOORS & FRAMES A Division of NATIONAL ASSOCIATION OF

More information

CLEAR-DIVISIONS APERTO

CLEAR-DIVISIONS APERTO CLEAR-DIVISIONS Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS moveable glass wall system. The yellow highlighted areas in the

More information

Fabrication Illustration Part No. Description Door Frame. P092 Mortised Butt Hinge P092D P092F (includes P2092 $ 48 $ 21 frame/door reinforcing)

Fabrication Illustration Part No. Description Door Frame. P092 Mortised Butt Hinge P092D P092F (includes P2092 $ 48 $ 21 frame/door reinforcing) Custom Blank Entrances - Applied Hardware & Preps - Tubelite Standard Hardware Butt Hinges Pivots C2 Page 1 P092 Mortised Butt Hinge P092D P092F (includes P2092 $ 48 $ 21 frame/door reinforcing) P795S

More information

SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS

SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word

More information

Black Sand Bronze We are a creative team based in New Zealand, we have been designing and making things for over 20 years, from the small scale of gold smithing to large civic projects, our passion is

More information

Andersen Clad Inswing Entry Doors (2001 to Present)

Andersen Clad Inswing Entry Doors (2001 to Present) Andersen Clad Inswing Entry Doors (2001 to Present) What s in This Section Clad Inswing Entry Doors Page 3 Part Illustrations 3 Parts Illustration - Single Door 3 Parts Illustration - Double Door 4 Parts

More information

ROUGH OPENING DIMENSION OPP. OPP. NET DOOR WIDTH NET DOOR WIDTH 1/8" OVERALL NET DOOR WIDTH DOOR OPENING ROUGH OPENING DIMENSION

ROUGH OPENING DIMENSION OPP. OPP. NET DOOR WIDTH NET DOOR WIDTH 1/8 OVERALL NET DOOR WIDTH DOOR OPENING ROUGH OPENING DIMENSION 1.5 2.1 2.3 1.1 OVERALL 1.5 2.8 2.8 2.2 2.3 2.1 3/8" NET DOOR HEIGHT 2.4 1.1 2.2 OVERALL 2.3 2.1 1.7 1.8 1.3 1.8 1.6 1.2 1.4 1.6 1.2 1.4 1.6 1.6 1.2 1.4 1.6 1 3/ 2.10 2.1 2.3 2.5 2.1 3/8" NET DOOR HEIGHT

More information

Series 3502 Thermal Series 3902 Fixed Thermal 3 1 4 Architectural Grade Horizontal Sliding Window

Series 3502 Thermal Series 3902 Fixed Thermal 3 1 4 Architectural Grade Horizontal Sliding Window Windows Curtain Walls Entrances Storefronts Series 3502 Thermal Series 3902 Fixed Thermal 3 1 4 Architectural Grade Horizontal Sliding Window Configurations XO OX XOX Fixed Series 3502 retains an AAMA

More information

C.R. LAURENCE COMPANY Worldwide Manufacturer and Supplier. Frameless and Framed Office Systems. CAT. NO. GW0S15 Glass Wall Office Systems

C.R. LAURENCE COMPANY Worldwide Manufacturer and Supplier. Frameless and Framed Office Systems. CAT. NO. GW0S15 Glass Wall Office Systems CAT. NO. GW0S15 Glass Wall Office Systems 08 1216 08 3200 08 4113 08 4126 10 2238 Frameless and Framed Office Systems C.R. LAURENCE COMPANY Worldwide Manufacturer and Supplier Glazing, Architectural, Railing,

More information

Installation Detailed installation instructions are provided which should be strictly followed.

Installation Detailed installation instructions are provided which should be strictly followed. Specification System 6 The Metal Technology Thermally-Broken Vertical Slide Window has been designed in such a way that its'attractive and clean lines will enhance all types of residential and commercial

More information

Size & Range. for windows & doors. Company

Size & Range. for windows & doors. Company Size & Range for windows & doors A Company B General information windows and doors Sizes This catalogue contains all Airlite s standard sizes for windows and doors. These are the ones that we make every

More information

CONFIGURATION 0 = fixed X = sliding. DOOR HEIGHT: 2100(h) Unit height 2090. DOOR HEIGHT: 2100(h) Unit height 2090

CONFIGURATION 0 = fixed X = sliding. DOOR HEIGHT: 2100(h) Unit height 2090. DOOR HEIGHT: 2100(h) Unit height 2090 ORIGIN PATIO DOOR SIDELIGHTS 0 = fixed X = sliding X Optional: Fly screen head and sill option. HEIGHT: Unit 10mm smaller 2210 2660 2960 3110 3560 4010 4460 Unit width as shown 300 600 900 PALACE SLIDING

More information

HARDWARE KITS. Hardware kits are designed for outswing use only. Inswing hardware available, please contact BROSCO for details.

HARDWARE KITS. Hardware kits are designed for outswing use only. Inswing hardware available, please contact BROSCO for details. Combination Storm & Screen Door COMBINATION STORM AND SCREEN DOOR Table of Contents Premium Hardware Kits... CDC-1 Deluxe Hardware Kits... CDC-1 & Mahogany Storm Doors... CDC-2 Storm Doors... CDC-3 Screen

More information

Wire Security Partitions & Cages Specification Guide

Wire Security Partitions & Cages Specification Guide Wire Security Partitions & Cages Specification Guide www.cisco-eagle.com/barriers Wire Partitions It doesn t have to be complicated... Cisco-Eagle publishes fully-illustrated, priced fast to order units

More information

Sample Calculations...V-CR-12. Door and Window Typical Combinations... V-CR-12 Horizontal and Vertical Typical Combinations...

Sample Calculations...V-CR-12. Door and Window Typical Combinations... V-CR-12 Horizontal and Vertical Typical Combinations... SECTION DIRECTORY General Information Definitions...V-CR- Design Considerations...V-CR- Composite Configurations...V-CR-4 Design Considerations and Examples for Typical Window and Door Combinations...V-CR-5

More information

Combination & Screen Doors

Combination & Screen Doors Combination & Screen Doors www.bbwood.com WOOD SCREEN DOORS Removable Screens (RS) SPECIFICATIONS: Stiles and Top Rail 2-9/16 Cross Rails Bottom Rail Vertical Mull 7/8 #206 #201 58-RS 764-RS V52-RS 2 2

More information

A Complete Solution CREATING WALLS THAT DEFINE SPACE

A Complete Solution CREATING WALLS THAT DEFINE SPACE A Complete Solution CREATING WALLS THAT DEFINE SPACE COMPANY HISTORY CLIPPER WALL Clipper partitions are part of the Saint- Gobain Group, one of the worldwide leaders in the construction products industry.

More information

Overhead Holders & Stops

Overhead Holders & Stops Manufacturing, Inc. Hospital Push/Pull Latches Electro-Magnetic Door Holders Electrical Power Transfer Products Aluminum Continuous Geared Hinges Stainless Steel Continuous Pin & Barrel Hinges Stainless

More information

Wood French Door Parts Reference Catalog

Wood French Door Parts Reference Catalog Parts Reference Catalog #010973 Revised 09/03 For Wood French Doors Built up to January 31, 2002 and for Special Orders From January 31, 2002 to February 1, 2003 This parts catalog represents a discontinued

More information

Sierra Pacific Windows

Sierra Pacific Windows Sierra Pacific Windows Bi-Fold Windows & Doors Sierra Pacific Bi-fold Windows and Doors glide smoothly to create large openings that transform your living spaces. With panels folding and stacking either

More information

Cluster Box Units. (CBU s) 3300 Series CBU Door Sizes. Fully Integrated Parcel Lockers CLUSTER BOX UNITS FRONT LOADING. continued on pages 7-11

Cluster Box Units. (CBU s) 3300 Series CBU Door Sizes. Fully Integrated Parcel Lockers CLUSTER BOX UNITS FRONT LOADING. continued on pages 7-11 Cluster Box Units (CBU s) continued on pages 7-11 CLUSTER BOX UNITS FRONT LOADING Made of heavy duty aluminum and stainless steel hardware, Salsbury 3300 series U.S.P.S. approved Cluster Box Units (CBU

More information

HARDWARE LOCATIONS FOR HOLLOW METAL DOORS AND FRAMES

HARDWARE LOCATIONS FOR HOLLOW METAL DOORS AND FRAMES HOLLOW METAL MANUAL NAAMM STANDARD HMMA 831-11 8d NAAMM HMMA 831-11 METAL DOORS & FRAMES HARDWARE LOCATIONS FOR HOLLOW METAL DOORS AND FRAMES 8d NAAMM HMMA 831-11 METAL DOORS & FRAMES A Division of HOLLOW

More information

glass entrance systems

glass entrance systems glass entrance systems Hardware: Center-Hung Pivots Top-Pivot Walking Beam Provides top pivot for center-pivoted, all-glass doors. Bottom-Pivot-Floor or Threshold Provides an adjustable bottom pivot for

More information

Class A Office Buildings Commercial Facilities College and University Campuses K-12 Buildings Healthcare Facilities Government & Military Structures

Class A Office Buildings Commercial Facilities College and University Campuses K-12 Buildings Healthcare Facilities Government & Military Structures Bringing New Light to Interior Architecture Expansive New Light Frameworks brings new light to interior architecture with doors, frames and windows that pair custom and standard glazing options with an

More information

Architectural Door Specifications Flush Doors 20 minute rating

Architectural Door Specifications Flush Doors 20 minute rating Section FRD Page 1 Architectural Door Specifications Flush Doors 20 minute rating Materials: Stiles: Laminated Timberstrand 38mm X 43mm Rails: Timberstrand 38 mm x 43 mm, extending the full width of the

More information

Transporter Food Conveyor System

Transporter Food Conveyor System Pass-Thru Windows Easi-Serv Unit 302 - Building D 6741 Cariboo Road Burnaby, B.C., Canada V3N 4A3 Toll Free: +1.888.591.0106 Tel: +1.604.422.8611 Fax: +1.604.422.8376 Transporter Food Conveyor System Patio

More information

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 08332 COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Counter Fire Doors. 1.2

More information

Can you design a frameless shower enclosure that doesn't leak?

Can you design a frameless shower enclosure that doesn't leak? Can you design a frameless shower enclosure that doesn't leak? With proper design and installation frameless shower enclosures should not have any problems with water leakage, but they are not 100 percent

More information

Basic Fire Door Requirements

Basic Fire Door Requirements TECHNICAL DATA SERIES S D I 118-01 Basic Fire Door Requirements 2001 Steel Door Institute STEEL DOOR INSTITUTE 30200 DETROIT ROAD - CLEVELAND, OHIO 44145 Technical Data Series SDI 118-2001 Basic Fire Door

More information

DORMA. Automatics. ESA Sliding Doors

DORMA. Automatics. ESA Sliding Doors DORMA Automatics ESA Sliding Doors DORMA ESA Historical Overview DORMA nearly 100 years old and still giving you fresh, innovative thinking. A history of innovative design. Since 1908, DORMA has been quietly

More information

glass & Glazing Products

glass & Glazing Products glass & Glazing Products WallMaker Create an unlimited variety of bright, beautiful and secure interior environments with the easy-to-install Stylmark WallMaker glass wall system. This versatile system

More information

SAMPLE TEST QUESTIONS GLAZER - ITA WEBSITE

SAMPLE TEST QUESTIONS GLAZER - ITA WEBSITE 1 Small amounts of hazardous chemicals used on several shifts are to be transferred from one container to another. How should the new container be labeled? A. Mark new container with product name only.

More information

Introduction...COMB-2 Design Considerations and Examples...COMB-3

Introduction...COMB-2 Design Considerations and Examples...COMB-3 SECTION DIRECTORY General Information Introduction...COMB-2 Design Considerations and Examples...COMB-3 Combination Assembly Recommendations and Limitations Composite Configurations...COMB-4 Typical Sealant

More information

City of San Diego, CWP Guidelines

City of San Diego, CWP Guidelines PART 1 -- GENERAL SECTION 08520-1.1 WORK OF THIS SECTION City of San Diego, CWP Guidelines A. The WORK of this Section includes providing aluminum windows with frames, bracing, glazing attachments, screens,

More information

A site plan or floor plan clearly identifying the location(s) of all new replacement window(s)

A site plan or floor plan clearly identifying the location(s) of all new replacement window(s) WINDOW REPLACEMENT GUIDELINES Community Development Planning & Building 2263 Santa Clara Ave., Rm. 190 Alameda, CA 94501-4477 alamedaca.gov 510.747.6800 F: 510.865.4053 TDD: 510.522.7538 Hours: 7:30 a.m.

More information

BASIC FIRE DOOR REQUIREMENTS TECHNICAL DATA SHEET NO. 401

BASIC FIRE DOOR REQUIREMENTS TECHNICAL DATA SHEET NO. 401 BASIC FIRE DOOR REQUIREMENTS SHEET NO. 401 Fire door openings are classified by their locations in the building. The location determines the length of exposure protection required, based on the potential

More information

CI/SfB. (31.59) X NOVEMBER 2003 Coburn Interior Sliding Systems

CI/SfB. (31.59) X NOVEMBER 2003 Coburn Interior Sliding Systems Uniclass L4181 EPIC D181 CI/SfB (31.59) X NOVEMBER 2003 Coburn Interior Sliding Systems Interior Sliding Door Gears FOR CUPBOARDS, WARDROBES, INTERIOR SLIDING AND FOLDING DOORS A comprehensive range of

More information

BYPASS TUB ENCLOSURE... 12 SLIDING DOOR AND FIXED PANEL SLIDING DOOR AND FIXED PANEL WITH RETURN PANEL SLIDING DOOR AND FIXED PANEL

BYPASS TUB ENCLOSURE... 12 SLIDING DOOR AND FIXED PANEL SLIDING DOOR AND FIXED PANEL WITH RETURN PANEL SLIDING DOOR AND FIXED PANEL HIGH PRECISION, QUALITY AND PERFORMANCE FEATURES... 2-3 IN-LINE BYPASS... 5-8 BYPASS SLIDING DOORS 2 SIDED BYPASS... 9-11 BYPASS SLIDING DOORS WITH RETURN PANEL BYPASS TUB ENCLOSURE... 12 BYPASS SLIDING

More information

Plaisance 24. Sliding Systems. Sapa Building System

Plaisance 24. Sliding Systems. Sapa Building System Plaisance 24 Sliding Systems Sapa Building System Plaisance 24 is Sapa s noninsulated sliding system for windows and doors. Available as one-, two-, three- and fourrail solution. Among its features, there

More information

MIAMI-DADE COUNTY PERFORMANCE TEST REPORT. Report No.: B8049.01-401-18. Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida

MIAMI-DADE COUNTY PERFORMANCE TEST REPORT. Report No.: B8049.01-401-18. Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida Architectural Testing MIAMI-DADE COUNTY PERFORMANCE TEST REPORT Report No.: B8049.01-401-18 Rendered to: AMERICAN PRODUCTS, INC Tampa, Florida PRODUCT TYPE: Aluminum Storefront with Double Doors SERIES/MODEL:

More information

Glass. Pre-Assembled Glass Entry Doors. In Stock Models Available! 1-800-486-8415

Glass. Pre-Assembled Glass Entry Doors. In Stock Models Available! 1-800-486-8415 Glass Store Front Doors 1-800-486-8415 www.glassstorefrontdoors.com Pre-Assembled Glass Entry Doors Commercial Glass Store Front Doors Pre-Assembled and Ready for Quick Install In Stock Models Available!

More information

HMMA 830 HARDWARE SELECTION FOR HOLLOW METAL DOORS AND FRAMES HOLLOW METAL MANUAL -02 NAAMM STANDARD METAL DOORS & FRAMES NAAMM 01 NAAMM 01

HMMA 830 HARDWARE SELECTION FOR HOLLOW METAL DOORS AND FRAMES HOLLOW METAL MANUAL -02 NAAMM STANDARD METAL DOORS & FRAMES NAAMM 01 NAAMM 01 HOLLOW METAL MANUAL NAAMM STANDARD HMMA 830-02 METAL S & FRAMES 8d NAAMM 01 02 HARDWARE SELECTION FOR HOLLOW METAL S AND FRAMES NAAMM 01 02 8d METAL S & FRAMES A Division of HOLLOW METAL MANUFACTURERS

More information

RTS88. Overhead Concealed Door Closer

RTS88. Overhead Concealed Door Closer RTS88 Overhead Concealed Door Closer RTS88 OVERHEAD CONCEALED CLOSER DORMA RTS88 OVERHEAD CONCEALED DOOR CLOSER Invisible door control Dependable and easy to install Architects are often challenged to

More information

Dependable and Versatile Floor-Concealed Closer

Dependable and Versatile Floor-Concealed Closer Floor-Concealed Door Closers Dependable and Versatile Floor-Concealed Closer The BTS80 Series of floor-concealed door closers offer adaptability to almost any installation. The closer s compact body permits

More information

Floor-Concealed Door Closers DORMA BTS80

Floor-Concealed Door Closers DORMA BTS80 Floor-Concealed Door Closers DORMA BTS80 Floor-Concealed Door Closers Dependable and Versatile Floor-Concealed Closer The BTS80 Series of floor-concealed door closers offer adaptability to almost any installation.

More information

TRANSOM AND SIDELIGHT FRAMES:

TRANSOM AND SIDELIGHT FRAMES: TRANSOM & SIDELIGHTS FIRE RATED PRODUCTS TRANSOM AND SIDELIGHT FRAMES: s Sidelight Frame Sidelight Frame Transom/Sidelight Frame Transom Frames with Bar FIRE RATED TRANSOM AND SIDELIGHTS: The transom and

More information

ASTM E 1886 and ASTM E 1996 TEST REPORT. Rendered to: CORAL ARCHITECTURAL PRODUCTS

ASTM E 1886 and ASTM E 1996 TEST REPORT. Rendered to: CORAL ARCHITECTURAL PRODUCTS Architectural Testing ASTM E 1886 and ASTM E 1996 TEST REPORT Rendered to: CORAL ARCHITECTURAL PRODUCTS SERIES/MODEL: PW 256 with Door Openings PRODUCT TYPE: Aluminum Impact Resistant Curtain Wall System

More information

Fire-rated Aluminum Doors

Fire-rated Aluminum Doors Fire-rated Aluminum Doors Langebjergvænget 13 ALUFLAM has pioneered the innovative solution to what was long considered an impossible dream (and a barrier to truly beautiful commercial architectural design),

More information

A ROAD MAP FOR YOUR CODE, SMOKE BARRIER & SMOKE PARTITION REQUIREMENTS

A ROAD MAP FOR YOUR CODE, SMOKE BARRIER & SMOKE PARTITION REQUIREMENTS A ROAD MAP FOR YOUR CODE, SMOKE BARRIER & SMOKE PARTITION REQUIREMENTS International Code Council National Fire Protection Association Underwriters Laboratories Inc. 5203 Leesburg Pike, Suite 600 1 Batterymarch

More information

Universal systems for frameless doors

Universal systems for frameless doors EN Universal systems for frameless doors Xinnix Door Systems designs, creates and manufactures systems for internal doors. With our construction elements, it is possible to obtain easily an elegant and

More information

LCN 2030 SERIES FEATURES CONCEALED (IN 1 3/4 HEADER) MOUNTING. The concealed 2030 Series. PACER is a heavy duty closer. designed to fit in a narrow,

LCN 2030 SERIES FEATURES CONCEALED (IN 1 3/4 HEADER) MOUNTING. The concealed 2030 Series. PACER is a heavy duty closer. designed to fit in a narrow, CONCEALED (IN 1 3/4 HEADER) MOUNTING The concealed 2030 Series PACER is a heavy duty closer designed to fit in a narrow, minimum 1 3/4 aluminum transom. The single lever arm and roller assembly provide

More information

Organisational Kitchen Fittings Kitchen Cabinet Fittings

Organisational Kitchen Fittings Kitchen Cabinet Fittings Pull-out wire storage basket Finish: Chrome plated Load capacity: 30 kg Installation depth: 400 mm Version: Runners and baskets separated, designed for wardrobe interiors without doors Type of pull out:

More information

Confort 26. Sliding Systems. Sapa Building System

Confort 26. Sliding Systems. Sapa Building System Confort 26 Sliding Systems Sapa Building System Confort 26 is Sapa s thermally insulated sliding system for windows and doors. Available as two- and three-rail solution. Among its features, there are

More information

Guidelines for Windows and Doors

Guidelines for Windows and Doors Guidelines for Windows and Doors WINDOWS AND DOORS Windows and doors typically comprise at least one quarter of the surface area of exterior walls of most historic buildings. Windows and doors, in addition

More information

Planet Frameless Glazing. Planet 20 frameless glass swing door

Planet Frameless Glazing. Planet 20 frameless glass swing door Planet Frameless Glazing Planet 20 frameless glass swing door Contents Introduction Pg 2 Planet 20 - Single Glazing Pg 3-7 Planet 100 - Double Glazing Pg 8-12 Joint Options Pg13 Sectional Drawings for

More information

280+ Mortise Mounted Series Shear Locks Special Application Solution

280+ Mortise Mounted Series Shear Locks Special Application Solution 280+ Mortise Mounted Series Shear Locks Power Plus control module overcomes gaps of up to 1/4" Low Temperature Operation 280+ TRD Locknetics provides the industry s most complete selection of electromagnetic

More information

Confort 160. Sliding Systems. Sapa Building System

Confort 160. Sliding Systems. Sapa Building System Confort 160 Sliding Systems Sapa Building System Confort 160 is a high performance thermally insulated sliding window system, with a user-friendly slide action. The system, which has an attractive aesthetic

More information

SECTION REFERENCE. Tilt-Wash Double-Hung. Insert Windows. 400 Series

SECTION REFERENCE. Tilt-Wash Double-Hung. Insert Windows. 400 Series SECTION REFERENCE Size Ranges... 96 Existing Window Measurements... 96 Divided Light Patterns... 97 Window Details... 97 Joining Details... 97 Performance Data... 269 400 Series Windows TILT-WASH DOUBLE-HUNG

More information

Cylinder Floor Bumpers with Screws. Cylinder Floor Bumpers with Dome Cap with Screws DOOR ACCESSORIES 11/2" 11/2" Cylinder Floor Bumper 1.

Cylinder Floor Bumpers with Screws. Cylinder Floor Bumpers with Dome Cap with Screws DOOR ACCESSORIES 11/2 11/2 Cylinder Floor Bumper 1. Cylinder Floor Bumpers with Screws 11/2" 2" 11/2" Cylinder Floor Bumper 2257 1.5" 2" 2" Cylinder Floor Bumper 2258 Dia. 1.170" Dia. 1.170" Cylinder Floor Bumpers with Dome Cap with Screws 11/2" Cylinder

More information

ARCHITECTURAL SPECIFICATIONS RHINO ADO 7000

ARCHITECTURAL SPECIFICATIONS RHINO ADO 7000 ARCHITECTURAL SPECIFICATIONS RHINO ADO 7000 LOW-ENERGY ELECTRIC SWING DOOR OPERATOR PART I - GENERAL 1.01 SUMMARY A. SECTION INCLUDES: Access Automation s low energy swing door operator. 1.02 REFERENCES

More information

CDW Systems Ltd Contemporary Doors & Windows

CDW Systems Ltd Contemporary Doors & Windows CDW Systems Ltd Contemporary Doors & Windows The comprehensive product overview A complete specification guide to CDW Systems range of Aluminium windows, doors and curtain walling for commercial and residential

More information

NanaWall SL73 - Thermally Broken Aluminum Framed Hurricane Rated Folding System with Miami Dade County, Florida NOA

NanaWall SL73 - Thermally Broken Aluminum Framed Hurricane Rated Folding System with Miami Dade County, Florida NOA NanaWall SL73 - Thermally Broken Aluminum Framed Hurricane Rated Folding System with Miami Dade County, Florida NOA ❶ PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: Sliding/folding aluminum and glass

More information

Surface Applied Door Closers DORMA TS93

Surface Applied Door Closers DORMA TS93 Surface Applied Door Closers DORMA TS93 DORMA TS93 Surface Applied Door Closers The TS93 System in Contur Design represents the pinnacle of surface applied closers because of its unique cam and roller

More information

Harrisburg Area Community College Harrisburg, PA. Request for Bid RFB15-19. For WHITAKER/BLOCKER DOOR REPLACEMENT

Harrisburg Area Community College Harrisburg, PA. Request for Bid RFB15-19. For WHITAKER/BLOCKER DOOR REPLACEMENT Dates: Harrisburg Area Community College Harrisburg, PA Request for Bid RFB15-19 For WHITAKER/BLOCKER DOOR REPLACEMENT DATE OF ISSUANCE: February 20, 2015 DATE OF SITE VISIT: February 26, 2015, 10:00 a.m.

More information

House Design Tutorial

House Design Tutorial Chapter 2: House Design Tutorial This House Design Tutorial shows you how to get started on a design project. The tutorials that follow continue with the same plan. When we are finished, we will have created

More information

Decorative Lever Designs

Decorative Lever Designs Decorative Lever Designs 3 & C 4 & K 12 14 & D 15 & A 16 & B 17 50 51 52 53 54 55 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 2 www.stanleysecuritysolutions.com

More information

Coburn The Buyers Guide OCTOBER 2007

Coburn The Buyers Guide OCTOBER 2007 Coburn The Buyers Guide OCTOBER 2007 The Buyers Guide FOR STRAIGHTAWAY, CORNAWAY, FOLDASIDE, CENTAFOLD, FAÇADE AND INTERIOR SLIDING SYSTEMS From modest beginnings manufacturing wheels in South London over

More information

Aluminium systems profile selection

Aluminium systems profile selection Aluminium systems profile selection The purpose of this document is to summarise the way that aluminium profile selection should be made, based on the strength requirements for each application. Curtain

More information

Leading Manufacturer of High Quality Builders Hardware in Canada

Leading Manufacturer of High Quality Builders Hardware in Canada Leading Manufacturer of High Quality Builders Hardware in Canada Since 1978 Your Solutions to Miscellaneous and Custom Architectural Hardware. Contents Product Description Page Contents 1 Numerical Index

More information

DIVISION 08 70 00 HARDWARE FORMAT 1. Technical specifications content and numbering system shall be based on 2004 CSI MasterFormat.

DIVISION 08 70 00 HARDWARE FORMAT 1. Technical specifications content and numbering system shall be based on 2004 CSI MasterFormat. FORMAT 1. Technical specifications content and numbering system shall be based on 2004 CSI MasterFormat. BASIS OF DESIGN 1. APSU design standards shall not replace fully developed, project and market specific

More information

NEWSTAR BROCHURE. December 2007

NEWSTAR BROCHURE. December 2007 NEWSTAR BROCHURE December 2007 Surface Overhead Door Closers Door Closing 5003 Silver Slide Cover SE Door Widths from 850mm to 1100mm. Door Weights 40kg to 80kg. Suitable for use in temperatures from -15

More information

RACO Interior OfficeFronts. SolutionsII Typical Details. SolutionsII

RACO Interior OfficeFronts. SolutionsII Typical Details. SolutionsII SolutionsII 1 SolutionsII Product Typical Overview Details I. GENERAL DESCRIPTION Work Included: Furnish all necessary materials, labor and equipment for the complete installation of interior aluminum

More information

Installation Instructions

Installation Instructions Installation Instructions READ BEFORE INSTALLING UNIT For Low Profile Window Air Conditioner INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step

More information

STOREFRONT DESIGN CRITERIA. Section II STOREFRONT DESIGN CRITERIA 2-1

STOREFRONT DESIGN CRITERIA. Section II STOREFRONT DESIGN CRITERIA 2-1 STOREFRONT DESIGN CRITERIA Section II STOREFRONT DESIGN CRITERIA 2-1 Philosophy and Storefront Design Concept The Shoppes at Grand Prairie will be the premier lifestyle specialty shopping center in the

More information

Series 602 MAGNUM Sliding Window DESIGNER SERIES

Series 602 MAGNUM Sliding Window DESIGNER SERIES Series 602 DESIGNER SERIES DATE: NOVEMBER 2009 REPLACES: AUGUST 2003 DESIGNER SERIES Series 602 KEY EATURES / PERORMANCE CHARACTERISTICS Scale: NOT TO SCALE Designed to complement our existing high quality

More information

1036 Parkway Ct. Phone: 770-932-0202 Buford, GA 30518 Fax: 770-945-0041

1036 Parkway Ct. Phone: 770-932-0202 Buford, GA 30518 Fax: 770-945-0041 CONSTRUCTION 1. A. GENERAL 1.A.1. The intent of this specification is to set forth construction and design standards that will result in an installation of modular cabinetry requiring FLUSH OVERLAY CONSTRUCTION.

More information

Providing the widest selection of quality vinyl and aluminum window & door products.

Providing the widest selection of quality vinyl and aluminum window & door products. Providing the widest selection of quality vinyl and aluminum window & door products. KELTIC DOOR SERIES At International Window, quality is our trademark. That is why we leave nothing to chance. Today,

More information

Floor-Concealed Door Closers with Electromagnetic Hydraulic Hold Open DORMA BTS80 EMB

Floor-Concealed Door Closers with Electromagnetic Hydraulic Hold Open DORMA BTS80 EMB Floor-Concealed Door Closers with Electromagnetic Hydraulic Hold Open DORMA BTS80 EMB Floor-Concealed Door Closers with Electromagnetic Hydraulic Hold Open Aesthetically Pleasing Floor Closer for Fire/Life

More information

Jonathan Elwell Bespoke Joinery Ltd. Unit H Greenfield Business Park 1 Greenfield, Holywell. CH8 7HJ

Jonathan Elwell Bespoke Joinery Ltd. Unit H Greenfield Business Park 1 Greenfield, Holywell. CH8 7HJ Our contemporary doors are made from solid wood. They are supplied pre-hung into the frame with a Secured by Design locking system, handles and a full factory stain or paint finish HB27 HB01 All our products

More information

GUIDELINES FOR REHABILITATION OF TRADITIONAL COMMERCIAL BUILDINGS DESIGN GUIDELINES

GUIDELINES FOR REHABILITATION OF TRADITIONAL COMMERCIAL BUILDINGS DESIGN GUIDELINES GUIDELINES FOR REHABILITATION OF TRADITIONAL COMMERCIAL BUILDINGS DESIGN GUIDELINES PAGE 13 DESIGN GUIDELINES The following design guidelines have been developed to guide appropriate design in the Downtown

More information

TOPLIGHTS. NOTE: 2.4m high sliding doors are only available in certain configurations and sizes.

TOPLIGHTS. NOTE: 2.4m high sliding doors are only available in certain configurations and sizes. NOTE: 2.4m high sliding doors are only available in certain configurations and sizes. Eagle Sidelights & Toplights Sidelights and Toplights are designed to clip onto the Eagle patio door system. The Sidelights

More information

9300BC SERIES Light Commercial Door Closer

9300BC SERIES Light Commercial Door Closer Light Commercial Door Closer general information The 9300BC is a durable, economically priced door closer designed for commercial exterior and interior doors such as storefront and industrial applications.

More information

Product Management - Glass ALEXA PRODUCT PRESENTATION. Region SAARC Nitin Lloyd, Product Management. Chennai, FY 2013 / 2014

Product Management - Glass ALEXA PRODUCT PRESENTATION. Region SAARC Nitin Lloyd, Product Management. Chennai, FY 2013 / 2014 Product Management - Glass ALEXA PRODUCT PRESENTATION Region SAARC Nitin Lloyd, Product Management Chennai, FY 2013 / 2014 PRODUCT MANAGEMENT - GLASS Alexa Partitioning Systems DESIGN: Slim Profile system

More information

CONCEALED BEARING HINGES. StANLEy ARCHItECtuRAL HARDwARE

CONCEALED BEARING HINGES. StANLEy ARCHItECtuRAL HARDwARE CONCEALED BEARING HINGES StANLEy ARCHItECtuRAL HARDwARE STANLEY ARCHITECTURAL HARDWARE TABLE OF CONTENTS Page Table of contents...2 Company history...2 5 knuckle concealed bearing design...3 Full mortise

More information

BLADE S-MAX Cabinet for Blade Server

BLADE S-MAX Cabinet for Blade Server Cabinet for Blade Server 1 2 Overview Material specification Corner verticals: 1.5 mm steel End frames: 1.5 mm steel Panel mounts: 2.0 mm steel Panel mount supports: 1.5 mm steel Side panels, door and

More information

Portman Sliding Door Gear Timber/Frames Doors Frameless Glass Doors

Portman Sliding Door Gear Timber/Frames Doors Frameless Glass Doors Portman Sliding Door Gear Timber/Frames Doors Frameless Glass Doors Top track Portman top tracks are suitable for door leaves of up to 80kg as standard Material is 6063T6 aluminium alloy anodised to 15

More information

Sliding Door Locks & Hardware. 5 a. Sliding & Pocket Door Locks Sliding Door Hardware Sliding Door Lever Lock

Sliding Door Locks & Hardware. 5 a. Sliding & Pocket Door Locks Sliding Door Hardware Sliding Door Lever Lock 5 Sliding Door Locks & Hardware 5 a 5 b 5 c Sliding & Pocket Door Locks Sliding Door Hardware Sliding Door Lever Lock 2016 02 2 2016 02 5 Sliding Door Locks & Hardware 5 a 3 4 6 8 12 13 14 17 18 Sliding

More information