Intermittent Wiper. PART # Rutherford St. P.O. Box 847 Goleta, CA FAX
|
|
- Rosaline Hampton
- 7 years ago
- Views:
Transcription
1 (Instructions for Midget start on Page 4) 1. Flip up the windshield wiper arms so that they do not touch the windshield. This will avoid scratches on the windshield. (Alternately, the arms can be temporarily removed from their mounting stalks. Put a short straight piece of tape on the end of one stalk so that its movement can be easily seen). Intermittent Wiper Installation Instructions MGB 1967 to 1980 (Negative ground) MG Midget 1967 to 1974 (Negative Ground) PART # Rutherford St. P.O. Box 847 Goleta, CA FAX Tools needed: Wire cutters, 12V test lamp, pliers, 9/32 drill. w/green stripe. (Alternately, you can use a 9/16 socket and ratchet to drop the steering column, remove the covers using a #2 phillips screwdriver and follow the wires from the wiper control switch under the dashboard). Wiper bundle 2. Look under the dashboard for the bundles of wire coming out of the steering column. 3. Choose where you would like to put the switch. If the steering column is between that switch location and the harness bundles under the dashboard, you may want to use a 9/16 socket and ratchet to drop the steering column and run the harness for the intermittent wiper switch over the steering column. Be sure that there will be enough depth for the switch and its harness connector. 4. Locate the bundle that connects to the wiper control switch. The bundle for the wiper control switch will have wires with the following wire colors: blue w/ green stripe, dark green, red w/green stripe and brown 5. Connect the test lamp to ground. Turn on the ignition and move the wiper control stalk to its highest setting (2). Now check the red wire with green stripe in the wiper control switch bundle. It should light up with a bright steady light. Now, switch off the wiper motor. The test lamp should go out once the wiper motor has reached the parked position. Turn off the ignition. 6. If, and only if, the wire tested follows the behavior laid out in step 4, cut the red with green wire and move the ends away from each other. The wiper motor should now no longer function at low speed. Red w/ green Revised 05/05
2 MGB Intermittent Wiper Installation Instructions 7. Temporarily slide harness for the the intermittent wiper switch onto the switch. 10. Connect the red wire of the intermittent control switch harness, which connects to terminal 15, to a positive lead which is live only when the ignition swtich is on. On our 1979 car, the positive lead is a solid white wire located in the wire bundle going to the ignition switch. There are actually a couple of solid white wires connected to this terminal. It is NOT a white with red wire. Use a test lamp connected to ground to check that the wire is live only when the ignition switch is on. 53M 53S 8. Connect the cut end that connects to the wiper motor to the terminal on the intermittent wiper harness that connects to terminal 53M. Put the red w/green wire into the front tubular groove of the snap-lock connector. Insert the wiper harness wire into the rear tubular groove. Do not let the end of either wire hang out of the connector. Press the metal tab of the snap-lock connector firmly in with pliers. Then fold the plastic wing over the body of the snap-lock connector until it clicks into position. Solid white wire 9. Connect the cut end that goes into the steering column and connects to the wiper control stalk switch to the terminal on the intermittent wiper harness that connects to terminal 53S. Solid white wire Red wire 11. Cut the forked connector off of the brown wire of the intermittent wiper control harness. Connect the brown wire of the intermittent control switch harness, which connects to terminal 31, to a negative ground. On our 1979 car, the negative ground is a solid black wire located in the wire bundle going to the ignition switch. Note that there was a brown wire on our 1979 car that is NOT ground. You are looking for a black wire. Use a test lamp connected to the positive Revised 05/05
3 MGB Intermittent Wiper Installation Instructions lead from Step 9 to check that the black wire you have chosen is connected to ground. 12. Turn the intermittent wiper control switch all the way counter-clockwise until it clicks (this is the off position). Turn on the ignition. The low and high speed windshield wiper settings should work. Turn the wiper control switch to the Off position and turn the wiper control switch clockwise. The wipers should operate with a delay. The further clockwise that the switch is turned, the greater the delay (adjustable from 2 to 20 seconds). NOTE: If the high and low speed settings work, the wiper delay switch operates (listen or watch for the clicks as it opens & closes its circuit), but the wipers do not traverse the windshield, check to make sure that you have not reversed the connections to 53M and 53S. 13. Once you have verified proper switch operation, mount the switch in the location you chose in Step 3. If the steering wheel is between your chosen switch location and the harness bundle connections, you may want to use a 9/16 socket and ratchet to drop the steering column and run the harness for the intermittent wiper switch over the steering column. Make sure that there Black wire Control Harness Brown wire Black wire will be room behind the switch for the switch and its harness connector. Use a 9/32 drill bit to make the mounting hole. Avoid drilling into any wiring that may be behind the hole for the switch. Optionally, you can use two screws and the backing plate provided to mount the switch under the dashboard. 14. Enjoy your new Intermittent Wiper Control. Please see MossMotors.com for all of your British Performance and Accessory needs. Four Harness Connections Revised 05/05
4 Midget Intermittent Wiper Installation Instructions Instructions for Midget (with positive ground): 1. Flip up the windshield wiper arms so that they do not touch the windshield. This will avoid scratches on the windshield. (Alternately, the arms can be temporarily removed from their mounting stalks. Put a short straight piece of tape on the end of one stalk so that its movement can be easily seen). 2. Look under the dashboard for the bundles of wire coming out of the steering column. stripe, black and brown w/green stripe. (Alternately, you can use a 9/16 socket and ratchet to drop the steering column, remove the covers using a #2 phillips screwdriver and follow the wires from the wiper control switch under the dashboard). Red w/green Red w/green Wiper bundle 3. Choose where you would like to put the switch. If the steering column is between that switch location and the harness bundles under the dashboard, you may want to use a 9/16 socket and ratchet to drop the steering column and run the harness for the intermittent wiper switch over the steering column. Be sure that there will be enough depth for the switch and its harness connector. 4. Locate the bundle that connects to the wiper control switch. The bundle for the wiper control switch will have several wires including the following wire colors: blue w/ green stripe, dark green w/white stripe, red w/green 5. Connect the test lamp to ground. Turn on the ignition and move the wiper control stalk to its highest setting (2). Now check the red wire with green stripe in the wiper control switch bundle. It should light up with a bright steady light. Now, switch off the wiper motor. The test lamp should go out once the wiper motor has reached the parked position. Turn off the ignition. 6. If, and only if, the wire tested follows the behavior laid out in step 4, cut the red with green wire and move the ends away from each other. The wiper motor should now no longer function at low speed Revised 05/05
5 Midget Intermittent Wiper Installation Instructions 7. Temporarily slide harness for the the intermittent wiper switch onto the switch. 9. Connect the cut end that goes into the steering column and connects to the wiper control stalk switch to the terminal on the intermittent wiper harness that connects to terminal 53S. 53M 53S 8. Connect the cut end that connects to the wiper motor to the terminal on the intermittent wiper harness that connects to terminal 53M. Put the red w/green wire into the front tubular groove of the snap-lock connector. Insert the wiper harness wire into the rear tubular groove. Do not let the end of either wire hang out of the connector. Press the metal tab of the snap-lock connector firmly in with pliers. Then fold the plastic wing over the body of the snap-lock connector until it clicks into position. 10. Connect the red wire of the intermittent control switch harness, which connects to terminal 15, to a positive lead which is live only when the ignition swtich is on. On our 1973 car, the positive lead is a solid white wire with a bullet connector on the end of it. It connects through a wrapped connection to two more white wires. It is NOT a white with red wire. Use a test lamp connected to ground to check that the wire is live only when the ignition switch is on. Solid white wire Red wire Revised 05/05
6 Midget Intermittent Wiper Installation Instructions 11. Cut the forked connector off of the brown wire of the intermittent wiper control harness. Connect the brown wire of the intermittent control switch harness, which connects to terminal 31, to a negative ground. On our 1979 car, the negative ground is a solid black wire located in the wire bundle going to the ignition switch. Note that there was a brown wire on our 1973 car that is NOT ground. You are looking for a black wire. Use a test lamp connected to the positive lead from Step 9 to check that the black wire you have chosen is connected to ground. Black wire 12. Turn the intermittent wiper control switch all the way counter-clockwise until it clicks (this is the off position). Turn on the ignition. The low and high speed windshield wiper settings should work. Turn the wiper control switch to the Off position and turn the wiper control switch clockwise. The wipers should operate with a delay. The further clockwise that the switch is turned, the greater the delay (adjustable from 2 to 20 seconds). 13. Once you have verified proper switch operation, mount the switch in the location you chose in Step 3. If the steering wheel is between your chosen switch location and the harness bundle connections, you may want to use a 9/16 socket and ratchet to drop the steering column and run the harness for the intermittent wiper switch over the steering column. Make sure that there will be room behind the switch for the switch and its harness connector. Use a 9/32 drill bit to make the mounting hole. Avoid drilling into any wiring that may be behind the hole for the switch. Optionally, you can use two screws and the backing plate provided to mount the switch under the dashboard. NOTE: If the high and low speed settings work, the wiper delay switch operates (listen or watch for the clicks as it opens & closes its circuit), but the wipers do not traverse the windshield, check to make sure that you have not reversed the connections to 53M and 53S. Control Harness Brown wire Four Harness Connections 14. Enjoy your new Intermittent Wiper Control. Please see MossMotors.com for all of your British Performance and Accessory needs Revised 05/05
Guide for Modified Assembly: Lightning McQueen. By: Collin Patterson, University of Delaware. Materials and Tools:
Guide for Modified Assembly: Lightning McQueen By: Collin Patterson, University of Delaware Materials and Tools: PVC o 40 inches of 1 in diameter PVC o 25 inches of ¾ in PVC o 4 x 1 in elbows o 2 x ¾ in
More informationMGA Alternator Conversion
MGA Alternator Conversion Installation Instructions For 1955 to 1962 MGA PART # 130-078 and #130-088 440 Rutherford St. P.O. Box 847 Goleta, CA 93117 1-800-667-7872 FAX 805-692-2525 www.mossmotors.com
More informationCONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N RUWRANGLER 1EA. 200 WATT AMP/BRACKET ASSEMBLY P/N RM11JKBTL - Bracket P/N RE08BTL200R - Amp 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More informationParts Required: Remove the Falcon Wiper Motor:
INTERMITTENT WINDSHIELD WIPERS + 2 SPEEDS By Dick Harrington If you frequently drive your Falcon or Comet, sooner or later you will get caught in the rain. The first item of defense for good vision is
More informationWalbro 255lph Inline Fuel Pump Install Procedure
Walbro 255lph Inline Fuel Pump Install Procedure Note: Instructions are based on a single in tank pump with under car OEM VW filter. Total install time for a qualified technician is approximately 2 hrs.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
More informationHow to modify a car starter for forward/reverse operation
How to modify a car starter for forward/reverse operation Ok, start by choosing a starter. I took a starter out of an older style Nissan Sentra. I chose this particular starter for two reasons: 1. It was
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 24393 ACCORD (DX, LX) SYSTEM 2-AND 4-DOOR Issue Date AUG 2002 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit panel
More informationWARNING! REQUIRED TOOLS & SUPPLIES: HIGH VOLTAGE
INSTRUCTIONS Product: GEM Electric Motorcars Models: All Subject: Instructions for installing Stereo Accessory Estimated Completion Time:.75 Hours Parts: See Page # 7 REQUIRED TOOLS & SUPPLIES: (1) 3/8
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2008 ACCORD 4-DOOR Publications No. AII 35362 Issue Date AUG 2007 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure
More informationMazda CX7 2007-09 99-7508
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Mount Radio Provision Stacked
More informationInstallation instructions, accessories. Cruise control. Volvo Car Corporation Gothenburg, Sweden. Instruction No Version Part. No. 30739998 1.
Instruction No Version Part. No. 30739998 1.1 Cruise control Page 1 / 11 Equipment A0000162 A0000161 A0801178 D8802049 Page 2 / 11 M8802108 Page 3 / 11 IMG-223164 Page 4 / 11 IMG-213320 Page 5 / 11 INTRODUCTION
More information4.3-inch Back-Up Camera
TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION
More information1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide
1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationWindshield Wiper Motors
Windshield Wiper Motors Originally posted by Dan Masters, danmas@aol.com Also see http://www.advanceautowire.com/ WIPER OPERATION: There are three major components to a wiper motor: Motor Rotary to linear
More informationWiper Motor Marinco 2.5. Installation Instructions
Wiper Motor Marinco 2.5 Installation Instructions Wiper Motor Marinco-2.5 The Marinco 2.5 Wiper Motor Offers the Following Features: Fully sealed base and housing which allows installation in outdoor wet
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror Kit with Compass and HomeLink 2. APPLICATION: Titan 3. PART NUMBER: 999L1 WS000 4. KIT CONTENTS: Item Qty Description Service
More informationSolstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More informationInstallation of Rear View Camera in a 1995 Roadtrek 190 Popular
Installation Instructions: 1995 Roadtrek Rear View Camera Page 1 Installation of Rear View Camera in a 1995 Roadtrek 190 Popular Introduction. In the fall of 2010 we investigated rear view cameras for
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More informationBODY-12, Door Handle - Removal, Installation, and Adjustment
Introduction BODY-12, Door Handle - Removal, Installation, and Adjustment There are many different procedures floating around describing how to replace the door handles on a 944 and every one of them will
More informationTOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation
TOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationDisassembling the Wii
Username: Password: Login Disassembling the Wii Method : Taking it Apart There are plenty of reasons to take apart a wii, whatever your case may be here's a guide to doing it. REQUIRED TOOLS AND ITEMS
More informationBack-Up Camera Installation Guide
Hz Hz In This Guide: Back-up camera installation requires connecting power wiring to the existing reverse lighting circuit and adding a chassis ground, as well as routing a video signal cable to the front
More informationI Click on a link tab to jump to that page. Cover Page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationINSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II
INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II ELECTRONIC TRAILER BRAKE CONTROL 5500 FOR 2, 4, 6 & 8 BRAKE SYSTEMS IMPORTANT: READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. KEEP THESE INSTRUCTIONS
More informationXenon HID Lighting System
Automotive Safety Systems User Installation Manual Preface Specifications Thank you for purchasing NOVABLUE Xenon H.I.D. (High Intensity Discharge) vehicle lighting systems. Before installing this product,
More informationInstallation instructions, accessories - Handsfree for cellular phone, system B, entry level
XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 0.5/1.1 2006 07 XC90 2003, XC90 2004 IMG-249663 Page 1 of 18 Required tools A0000162 A0000163 IMG-239664 M0000232 IMG-253123 IMG-252223 Page 2 of 18
More informationI Click on a link tab to jump to that page. Cover Page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationKEYPAD LOCK RETROFIT KIT
KEYPAD LOCK RETROFIT KIT INSTRUCTIONS FOR ASSEMBLY IMPORTANT READ & SAVE THESE INSTRUCTIONS Tools Required for Assembly 5/32 hex (Allen) wrench #2 Phillips screwdriver Isopropyl alcohol or alcohol wipes
More informationPower Window/Power Lock Installation. To begin with you will need all the parts listed below:
Power Window/Power Lock Installation To begin with you will need all the parts listed below: From Donor Fiero: Fiero power window regulators Power window motors (Generic GM type part) -motors are riveted
More informationTOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00112 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2009 PILOT Publications No. AII 39408 Issue Date MAY 2008 PARTS LIST Steering Wheel Trim (With Cruise and Audio) P/N 08Z13-SZA-130B (Chocolate) P/N 08Z13-SZA-140B
More informationOperations Manual SledStart H4 HID Light Kit
Operations Manual SledStart H4 HID Light Kit ` Table of Contents INTRODUCTION...1 SAFETY WARNING...1 PACKAGE CONTENTS...1 INSTALLATION INSTRUCTIONS...2 NOTES... 7 Copyright 2010 SledStart LLC All Rights
More informationCOOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011
COOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011 Below are instructions for the Mini Mania Pulley Upgrade Kit, Part Number NME5011. Please take all necessary precautions for working
More informationHP Laser Jet 4200/4240/4250/4300/4350 Swing Plate
HP Laser Jet 4200/4240/4250/4300/4350 Swing Plate 1 Swing Plate Assembly-RM1-0043 1 Swing Plate Kit-5851-2766 (RM1-0043 plus RM1-1091 gear) CAUTION: Fuser may be hot. Turn off printer, unplug it and allow
More informationInstalling RNS-E SAT NAV for Audi A4
As one of the major options on the A4 you can get a DVD Satellite Navigation System call the RNS-E. With the help of ebay these sat nav systems are now available to by at a rough cost of 650 plus the cost
More informationCover Page. Factory Radio Other Documents Available For This Vehicle:
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,,2000. Factory Radio
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationBuild Your Own Solar Car Teach build learn renewable Energy! Page 1 of 1
Solar Car Teach build learn renewable Energy! Page 1 of 1 Background Not only is the sun a source of heat and light, it s a source of electricity too! Solar cells, also called photovoltaic cells, are used
More informationDocument number RS-PRD-00130 Revision 05 Date 20/10/2009 Page 1/30
Date 20/10/2009 Page 1/30 1. Purpose This document describes the field replacement of the footscan plate cable for these models: 2m hi-end plate SN 11/5/xxx 2m pro plate SN 7/5/xxx 0.5m 2003 hi-end plate
More informationPost Mount Light Installation*
Post Mount Light Installation* *For the general installation of most Post Mount Spotlights, many vehicles may need slight modifications to these instructions. You will need the following tools: High torque
More informationKEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER
KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-30915 Contents PARTS LIST... 2 PARTS ILLUSTRATIONS... 2 VEHICLE PREPARATION... 3 INSTALLING
More information5 Mechanisms and accessories
5 Mechanisms and accessories 51A SIDE OPENING ELEMENT MECHANISMS 52A NON-SIDE OPENING ELEMENT MECHANISMS 54A WINDOWS 55A EXTERIOR PROTECTION 56A EXTERIOR EQUIPMENT 57A INTERIOR EQUIPMENT X79 NOVEMBER 2009
More informationMulti Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter
MODEL PRO-9744 INSTALLATION MANUAL Multi Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter This System Allows The Transmitter Buttons To Be
More informationIntelliChlor Flow-Temperature Switch Replacement Kit Installation Guide
IntelliChlor Flow-Temperature Switch Replacement Kit Installation Guide Technical Support Sanford, North Carolina (8 A.M. to 5 P.M.) Moorpark, California (8 A.M. to 5 P.M.) Phone: (800) 831-7133 Fax: (800)
More informationhttp://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html
http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html TECHNICAL SERVICE DEPARTMENT Removal, Cleaning, & Reinstallation of the Burner Assembly For models 74 & GT199 Required tools -
More informationTOOL SVC NUMBERS: 250-2598, 250-2600 SVC CONTENTS ITEM QTY DESCRIPTION PART NUMBER 1 1 CUTTING TOOL 250-2598 2 1 EXTRACTION TOOL/PART# 250-2600
07-08 TOYOTA FJ CRUISER, 05-09 SIENNA, 06-08 SCION TC PART NUMBER: 250-1732 1 CRUISE CONTROL KIT TOOL SVC NUMBERS: 250-2598, 250-2600 2 2 1 BASE KIT CONTENTS ITEM QTY DESCRIPTION 1 1 CONTROL SWITCH ASSEMBLY
More informationLeft Hand Limit Switch. Housing. Left Hand. Connections. Motor Connector BROWN PURPLE GRAY BLACK DARK BLUE BLACK BROWN BROWN LIGHT BLUE.
LIGHT BLUE GRAY PURPLE Circuit Breaker Intput Circuit Breaker Output #1 Relay Left Hand Limit Switch Housing Left Hand Motor Connector Right Hand Limit Switch on Radiator Support Right Hand Limit Switch
More information2003/2004/2005 TOYOTA COROLLA
2003/2004/2005 TOYOTA COROLLA KEYLESS ENTRY UPGRADE SECURITY SYSTEM INSTALLATION INSTRUCTIONS KIT NO. 00016-30120 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have
More informationC5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions
C5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions Ok, let's start with taking the radio bezel dash area off first. Here is what the OEM radio looks like... First you flip
More informationChevy Equinox 2010-2015 / GMC Terrain 2010-2014 (with monochrome display) 99-3307G
INSTALLATION INSTRUCTIONS FOR PART 99-3307G Chevy Equinox 2010-2015 / GMC Terrain 2010-2014 (with monochrome display) 99-3307G KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision
More informationCUSTOM AUXILIARY FORWARD LIGHTING KIT
-J0 REV. 0--0 CUSTOM AUXILIARY FORWARD LIGHTING KIT GENERAL Kit Number -0, 0000 Models This Custom Auxiliary Lighting Kit adds lamps and turn signals to 00 and later FLHX model motorcycles. Additional
More informationMazda CX7 2010-up 99-7520B
INSTALLATION INSTRUCTIONS FOR PART 99-7520B APPLICATIONS Mazda CX7 2010-up 99-7520B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Painted matte
More informationBuilding A Computer: A Beginners Guide
Building A Computer: A Beginners Guide Mr. Marty Brandl The following was written to help an individual setup a Pentium 133 system using an ASUS P/I- P55T2P4 motherboard. The tutorial includes the installation
More informationKVT-729DVD INSTALLATION MANUAL
MONITOR WITH DVD RECEIVER KVT-729DVD INSTALLATION MANUAL B54-4516-00/00 (EV) Accessories 1 0...1...1 2!...1...2 3...1 4 5...1...1 6...2 7...4 8...4 9...2 2 KVT-729DVD Installation Procedure 1. To prevent
More informationhttp://mbworld.org/forums/c32-amg-c55-amg-w203/449471-famous-ac-clicking-noiseac-footwell-damper-linkage-replacement-diy-details-steps.
Air Conditioner / HVAC W203 Stepper Motor Repair PART 2 OF 3 forums/c-class-w203/177068-noisy-air-conditioner-stepper-motorreplacement-clicking-hissing.html forums/c32-amg-c55-amg-w203/449471-famous-ac-clicking-noiseac-footwell-damper-linkage-replacement-diy-details-steps.html
More informationINSTALLATION GUIDE. APPLICATION LENGTH MODEL YR PART # Bestop PART #
INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Bestop PART # Ford Super Duty F-250 / F-350 Regular Cab (48 ) 1999 2007 10-02513-24 75102-01 Ford Super Duty F-250 / F-350 Super Cab (60 ) 1999 2007
More informationILISC515-A Shift Interlock (Manual Lift Door) 2015 Ford Transit, 3.7L and 3.5L
An ISO 9001:2008 Registered Company ILISC515-A Shift Interlock (Manual Lift Door) 2015 Ford Transit, 3.7L and 3.5L Introduction The ILISC515-A is a microprocessor driven system for controlling wheelchair
More informationWireless Reverse Parking Camera
Wireless Reverse Parking Camera RAC-HP102 This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to
More informationINTRODUCTION INTERLOCK KIT K-8110
INTRODUCTION INTERLOCK KIT K-8110 This manual provides instructions for safe installation of the InterLock Kit onto a General Electric (GE) panel. The back plate sits securely on the face of the panel
More informationGripper Kit for the Boe-Bot Robot (#28202)
599 Menlo Drive, Suite 100 Rocklin, California 95765, USA Office: (916) 624-8333 Fax: (916) 624-8003 General: info@parallax.com Technical: support@parallax.com Web Site: www.parallax.com Educational: www.stampsinclass.com
More informationGTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com
GTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com This procedure covers replacing the front wheel bearings. Tools and Parts required: Wheel Bearing Puller w/ ABS adapter. Available for rent from
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationTriac Printed Circuit Board Replacement
Technical Service Bulletin: Triac Printed Circuit Board Replacement TRONIC 5000C Pro Models: WH17, WH27, WH36 Introduction Fig. 1 ELECTRICITY IS EXTREMELY DANGEROUS. TAKE EXTRA PRECAUTIONS AND ENSURE ALL
More informationPARTS & INSTALLATION INSTRUCTIONS MEYER SNOW PLOW LIGHTS
Form 1-696 R1 January, 2003 PARTS & INSTALLATION INSTRUCTIONS MEYER SNOW PLOW LIGHTS PARTS LIST ITEM PART NO. QTY. DESCRIPTION 07033 1 SNOW PLOW LIGHT CARTON 1 07034 1 Snow Plow Light, Pass. Side (No Hardware)
More informationTOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation
Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43
More informationHeat Surge Model X5C Fire Place Insert Service Manual Applies to all units w/30000208 circuit board
Heat Surge Model X5C Fire Place Insert Service Manual Applies to all units w/30000208 circuit board 2012 HS M4417A BR16597R-1 HEAT SURGE 8000 FREEDOM AVE, N. CANTON, OH 44720 330-244-8161 WWW.HEATSURGE.COM
More informationTABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2
BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section
More information89 to 93 Dashboard Removal. Created for Miata.net Members by Anthony Meeks (SE1686)
89 to 93 Dashboard Removal Created for Miata.net Members by Anthony Meeks (SE1686) Intro When I bought my 91 SE, the paint on the top of the dashboard was in terrible shape and I immediately determined
More informationAlfa Romeo 147 On board instruments installation guide
Alfa Romeo 147 On board instruments installation guide Alfa Romeo 147 On board instruments installation guide This guide is describing how I installed oil temperature and oil pressure gauges to my Alfa
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationBulb Replacement REPLACING BULBS WARNING
Bulb Replacement REPLACING BULBS Check the operation of all exterior lamps before you drive the vehicle. Caution: Before attempting to replace a bulb, ensure that both the affected lamp and the vehicle's
More informationA&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS
A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.
More informationSpreader Light Bulb Replacement Instructions
Spreader Light Bulb Replacement Instructions IMPORTANT: DISCONNECT LIGHT FROM BATTERY BEFORE PROCEEDING. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR OTHER DAMAGE. Tools Needed You will need the following
More informationBoxster. Technical Information. Service 3/99 9415. Litronic Retrofit Kit
Litronic Retrofit Kit 9 3/99 9415 Binder - 9, Electrics This bulletin replaces bulletin Grp. 9, #3/99, dated 5-20-99. Vehicle Type: Model Year: Concern: Information: As of 1997 (V) Retrofitting Litronic
More informationALBINS SEQUENTIAL SHIFTER
ALBINS SEQUENTIAL SHIFTER Updated 12/11/11 8-AGB5-INST GENERAL NOTES The Albins Sequential Shifter is specifically designed for AGB transaxles. It features an integral reverse lockout lever and has a position
More informationMazda CX9 2007-up 99-7516B
INSTALLATION INSTRUCTIONS FOR PART 99-7516B APPLICATIONS Mazda CX9 2007-up 99-7516B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Stacked ISO units
More informationTOYOTA TUNDRA 2015 Billet Grille w/led DRL
TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3
More informationINSTALLATION MANUAL 3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS
3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS INSTALLATION MANUAL Before you begin the installation Read the INSTRUCTIONS! Always use a multi-meter when verifying vehicle wiring. Before mounting the
More informationBuild a Junior Solar Sprint Model Car Kit Materials: 1 PITSCO Ray Catcher Sprint Kit or Solar Made Junior Solar Sprint Kit 1 White Sheet of Plastic
Build a Junior Solar Sprint Model Car Kit Materials: 1 PITSCO Ray Catcher Sprint Kit or Solar Made Junior Solar Sprint Kit 1 White Sheet of Plastic Coated Paper 2 Balsa Sheets (10-1/2 x4 x3/16 ) 2 Alligator
More informationInstallation instructions, accessories - Navigation system, RTI
XC90 Section Group Weight(Kg/Pounds) Year Month 3 393 4/8.8 2007 08 Page 1 of 20 Required tools A0000162 IMG-239667 IMG-239664 IMG-239980 IMG-242205 R8802817 R3905015 Page 2 of 20 R3903812 IMG-213320 Page
More informationNavico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement
Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations
More information17. LIGHTS/INSTRUMENTS/SWITCHES
17 SERVICE INFORMATION... 17-0 IGNITION SWITCH... 17-3 TROUBLESHOOTING... 17-0 STOP SWITCHES/HORN... 17-4 FUEL UNIT... 17-1 INSTRUMENTS... 17-4 HANDLEBAR SWITCHES... 17-2 HEADLIGHT/LIGHTS... 17-5 17 SERVICE
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9612 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: FORD FOCUS SE & S MODELS (AT/MT) FORD TRANSIT ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
More informationhttp://mbworld.org/forums/c32-amg-c55-amg-w203/449471-famous-ac-clicking-noiseac-footwell-damper-linkage-replacement-diy-details-steps.
Air Conditioner / HVAC W203 Stepper Motor Repair PART 3 OF 3 forums/c-class-w203/177068-noisy-air-conditioner-stepper-motorreplacement-clicking-hissing.html forums/c32-amg-c55-amg-w203/449471-famous-ac-clicking-noiseac-footwell-damper-linkage-replacement-diy-details-steps.html
More information09 19 WIPER/WASHER SYSTEM
09 19 WIPER/WASHER SYSTEM LOCATION INDEX................. 09 19 2 Windshield Wiper and Washer System 09 19 2 Rear Wiper and Washer System..... 09 19 3 WIPER/WASHER SYSTEMS WIRING DIAGRAM................
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual
More informationINSTALLATION MANUAL. Installation Instructions
INSTALLATION MANUAL Power-Pole Signature Series Shallow Water Anchor Installation Instructions CAUTION: Read this instruction manual carefully. Become familiar with the controls and know how to operate
More informationNetworkfleet 3500 Product Line Installation Guide
Networkfleet 3500 Product Line Installation Guide Light/Medium Duty (L3500) Heavy Duty (H3500) Universal (U3500) www.networkcar.com/fleet Customer Care: (866) 227-7323 customercare@networkcar.com Table
More information