NP SERIES FOR GENERAL PURPOSE, STANDARD SIZE, 85
|
|
|
- Margery Hancock
- 7 years ago
- Views:
Transcription
1 NP SERIES FOR GENERAL PURPOSE, STANDARD SIZE, 85 Applicable Standard Characteristic W of JIS C 5141 Operating Temperature Range -40 ~+85 Rated Working Voltage Range 6.3~250 V.DC Rated Voltage and Surge Voltage Rated Voltage (V) Surge Voltage (V) DC Leakage Current Applying the rated DC voltage to the capacitor. The leakage current is measured at 5 minutes after the DC voltage across the capacitor reached the rated voltage. The leakage current shall not exceed the value below. (at 25 ) I 0.03 CV or 3μA, whichever is greater Where, I: Leakage Current (μa) C: Nominal Capacitance (μf) V: Rated Voltage (V) Capacitance Tolerance The capacitance shall be within the following tolerance to the nominal capacitance. -20%~+20% (At 25, 120Hz) Tangent of Loss Angle (Tanδ) Tanδ shall not exceed the value below. (At 25, 120Hz). When nominal capacitance is over 1000μF. Tanδ shall be added 0.02 to the listed value with increase of every 1000μF. Rated Voltage (V) Tanδ Temperature Characteristics Impedance ratio of the -25 or -40 value to the 25 value shall not exceed the value below. (At 120Hz) Rated Voltage (V) ~ ~250 Z(-25 )/Z(25 ) Z(-40 )/Z(25 ) WANMING ELECTRONICS CO., LTD. PAGE: 4/9
2 Load Life The following specifications shall be satisfied when the capacitors are restored to 25 after the rated voltage is applied for 2000 hours at 85. Capacitance Change ±20% of the initial value. Tanδ 200% of the initial specified value. Leakage Current The initial specified value. Shelf Life The following specifications shall be satisfied when the capacitors are restored to 25 after exposing them for 500 hours at 85 without voltage applied. The capacitors shall be subjected to voltage treatment specified in item 4.4 of JIS C 5102, before the measurements. Capacitance Change ±20% of the initial value. Tanδ 200% of the initial specified value. Leakage Current The initial specified value. Solder ability The lead wires shall be dipped into Methanol (JIS K 1501) or Isopropyl Alcohol (JIS K 1522 or JIS K 8839) solution of 10 ±20% Rosin (JIS K 5902) for 2 ±0.5 seconds, and then dipped into solder H63A (JIS Z 3282) at 235 ±5 for 2 ±0.5 seconds. The depth of immersion shall be 2 to 2.5 mm of the capacitor body. After immersion, the solder shall cover at least 3/4 of the lead wire surface immersed. Lead Strength Pull Strength The lead wire shall not get loose or cut off, while a parallel force is gradually applied to the lead wire up to 5N and retained for 10 second. Bending Strength Apply the 0.25Kg weight to the end of the lead wire, and lean the capacitors body 90 and return to the original position within approximately 5 seconds. Then, repeat this cycle in the posite direction at the same speed. After that, the lead wire shall not loose or cut off. WANMING ELECTRONICS CO., LTD. PAGE: 5/9
3 Marking Color Style: white marking on dark-green sleeve. The following items shall be marked on each capacitor. Example: (1) Series Name (2) Maximum Operating Temperature VENT WMEC NP xxμfxxv 85 (M) (3) Capacitance Tolerance (4) Safety Device Marking WM EC NP (Safety vent more than 8mm Diameter product) xxμfxxv 85 (M VENT (5) WMEC Electronics Co., Ltd. Marking (6) Nominal Capacitance (7) Rated Voltage Dimensions α ψd F ψd or or α WANMING ELECTRONICS CO., LTD. PAGE: 6/9
4 Case Size & Permissible Max. Ripple Current Case Size :ψd L Max. Ripple Current : ma (rms) ( 85, 120Hz) WV μf SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C X x X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X WV μf SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C. SIZE R.C X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Ripple current (marms)at85.120hz Case sixe ψdxl WANMING ELECTRONICS CO., LTD. PAGE: 7/9
5 Ripple Current Coefficients Frequency Multipliers Freq.(Hz) Cap.(μF) 60(50) K 10K 0.1 ~ ~ ~ Temperature Multipliers Temp. ( ) coefficient Packaging Specification Case size ψd L Plastic Bag Capacity pcs. / per bag Small Box Capacity Bag / per small box pcs. / per small box Carton Box Capacity small box / per carton box pcs. / per carton box Small Box Size Carton Box Size L H W L H W , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , WANMING ELECTRONICS CO., LTD. PAGE: 8/9
6 The following items shall be marked on the box. Customer WANMING P/N PO. No. ot No. Customer P/N Final Date Description Inspection Quantity PCS. Other For other specifications, Characteristic W of JIS C 5141 shall be satisfied. Corrosion, which is caused by and homogenate hydrocarbon solvents may damage aluminum Electrolytic Capacitors. Please let us know in advance the solvent name and conditions for your P.C.B. cleaning. We guarantee our products without any prohibited substance about environment. WANMING ELECTRONICS CO., LTD. PAGE: 9/9
SMD Aluminum Solid Capacitors with Conductive Polymer
SMD Aluminum Solid Capacitors with Conductive Polymer FEATURES New OS-CON series provides improved characteristics with up to 25 C temperature capability and 35 V maximum voltage rating in a SMD package
handbook, 2 columns handbook, halfpage 085 CS
FEATURES Polarized aluminium electrolytic capacitors, non-solid, self healing Extended voltage and capacitance range SMD-version, fully moulded, insulated Flexible terminals, reflow and wave solderable
Aluminum Electrolytic Capacitors Power Eurodin Printed Wiring
Aluminum Electrolytic Capacitors Power Eurodin Printed Wiring 00/0 PEDPW Fig. QUICK REFERENCE DATA DESCRIPTION VALUE 00 0 Nominal case size (Ø D x L in mm) x 0 to 0 x 00 Rated capacitance range 0 μf to
Ceramic Trimmer Capacitors
!Note T3E8.pdf 2.9.2 Ceramic Trimmer Capacitors TZB4 Series.±. Depth.5.4±. dia. Features. Miniature rectangular shape : 4.(W)x4.5(L)x3.(H)mm. 2. Color coded case facilitates identification of capacitance
Aluminum Electrolytic Capacitors Power Economic Printed Wiring
Aluminum Electrolytic Capacitors Power Economic Printed Wiring 0/0 PECPW 00/0 PEDPW Fig. QUICK REFERENCE DATA DESCRIPTION high ripple current 0/0 PECPW long life 0 C Nominal case size (Ø D x L in mm) Rated
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications FEATURES AEC-Q200 qualified with PPAP available Available in 0402 to 1812 body size Three dielectric materials AgPd termination
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free Product Specification October 13, 11 V.8 Product
Powering Integrated Circuits (ICs), and managing ripple voltage as it relates
Ripple Voltage & ESR Powering Integrated Circuits (ICs), and managing ripple voltage as it relates to ESR of capacitors Low voltage ICs require supply voltage (Vcc) to have reduced levels of ripple voltage
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life 38 AML 0 ASM smaller dimensions Fig. QUICK REFERENCE DATA DESCRIPTION Nominal case sizes (Ø D x L in mm) 6.3 x.7 to 0 x 5 VALUE 0 x 30 to x 38
3mm Photodiode,T-1 PD204-6C/L3
3mm Photodiode,T-1 Features Fast response time High photo sensitivity Small junction capacitance Pb free This product itself will remain within RoHS compliant version. Description is a high speed and high
AC and Pulse Film Foil Capacitors KP Radial Potted Type
AC and Pulse Film Foil Capacitors KP Radial Potted Type 0.5 L max. W max. Marking H max. FEATURES 5 mm lead pitch, supplied loose in box taped in ammopack or reel Material categorization: for definitions
Aluminum Electrolytic Capacitors Radial Miniature, Low Impedance, High Vibration Capability
Aluminum Electrolytic Capacitors Radial Miniature, Low Impedance, High Vibration Capability 048 RML 48 RUS lower longer life 36 RVI miniaturize 50 RMI high vibration FEATURES Very long useful life: 7000
EMERGENCY EGRESS LIGHTING POWER SUPPLY PART NO. 5925-6 COMPONENT MAINTENANCE MANUAL WITH ILLUSTRATED PARTS LIST
EMERGENCY EGRESS LIGHTING POWER SUPPLY PART NO. WITH ILLUSTRATED PARTS LIST Initial Issue: June 16, 1995 33-51-80Page 1 May 20/2010 RECORD OF REVISIONS REV. NO. ISSUE DATE A 01-26-96 B 09-21-99 C 10-26-09
AS2815. 1.5A Low Dropout Voltage Regulator Adjustable & Fixed Output, Fast Response
1.5A Low Dropout oltage Regulator Adjustable & Fixed Output, Fast Response FEATURES Adjustable Output Down To 1.2 Fixed Output oltages 1.5, 2.5, 3.3, 5.0 Output Current of 1.5A Low Dropout oltage 1.1 Typ.
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications ELECTRICAL SPECIFICATIONS X7R GENERAL SPECIFICATION Note Electrical characteristics at +25 C unless otherwise specified
Product Specification
Sheet 1/7 Polymer Lithium-ion Battery (For high discharge ratio battery) Model:GEB201212C General Electronics Battery Co., Ltd. Address: Huihuang Industrial Building, Huada Road, Dalang, Longhua, Baoan
Electrical Double Layer Energy Storage Capacitors Power and Energy Versions
Electrical Double Layer Energy Storage Capacitors Power and Energy Versions FEATURES Polarized energy storage capacitor with high capacity and energy density Energy version with high stability available
Application Note TMA Series
1W, SIP, Single & Dual Output DC/DC Converters Features SIP Package with Industry Standard Pinout Package Dimension: 19.5 x 10.2 x 6.1 mm (0.77 x 0.4 x 0.24 ) 5V&12V Models 19.5 x 10.2 x 7.1 mm (0.77 x
www.jameco.com 1-800-831-4242
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. SPECIFICATION CUSTOMER: JAMES DATE: 04.08.23 MODEL NO: DBU090030 DESIGNED
Chip tantalum capacitors
Chip tantalum capacitors TC Series Case Features 1) Small package, large capacitance chip tantalum capacitor. 2) Low impedance capacitors. 3) Screening by thermal shock. Dimensions node mark (Unit : mm)
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 50 V DC, 100 V DC and 200 V DC
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 5 V DC, 1 V DC and 2 V DC DESIGNING For more than 2 years Vitramon has supported the automotive industry
DC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type FEATURES 15 mm to 27.5 mm lead pitch. Supplied loose in box and taped on reel Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
Aluminum Capacitors Solid Axial
SAL-A End of Life. Last Available Purchase Date is -December- Radial higher CV/volume Fig. QUICK REFERENCE DATA DESCRIPTION VALUE Maximum case size (Ø D x L in mm) 6.7 x. to.9 x. Rated capacitance range
DATA SHEET THICK FILM CHIP RESISTORS Introduction
DATA SHEET THICK FILM CHIP RESISTORS Introduction Product Specification Product specification 2 Chip Resistor Surface Mount Data in data sheets is presented - whenever possible -according to a 'format',
SuperTan Extended (STE) Capacitors, Wet Tantalum Capacitors with Hermetic Seal
SuperTan Extended () Capacitors, Wet Tantalum Capacitors with Hermetic Seal FEATURES SuperTan Extended () represents a major breakthrough in wet tantalum capacitor Available technology. Its unique cathode
SPECIFICATION. Topview 5550 SMD LED IWS 505-RB. Product : Topview 5550 SMD LED Part No : IWS-505-RB Customer : Date : 2007. 11. 10 Ver.1.0.
SPECIFICATION Product : Topview 555 SMD LED Part No : Customer : Date : 27.. Ver.. Customer : Approval Manufacturer : ITSWELL Co., LTD Proposed By Approval Comment Suwon Company : 442-9, 82 Uman Industrial
帝 聞 企 業 股 份 有 限 公 司 DEE VAN ENTERPRISE CO., LTD. SP-235864 DSL-20WA 420024 1 Revision: A Date: 2011.10.24 FOR AC-DC LED DRIVER MODEL NO.
CUSTOMER: PART NUMBER: A200 APPROVAL SHEET FOR AC-DC LED DRIVER MODEL NO. DSL-20WA 420024 1 ORDER NO: SP-235864 承 認 書 确 認 后 請 簽 回 一 份 CUSTOMER APPROVED SIGNATURE DEE VAN ENTERPRISE CO., LTD (Head-Quarter)
DC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type MKT80 FEATURES AEC-Q00 qualified (rev. D) for PCM. mm (for larger available components on request) High temperature capabilities, up to 0 C Capacitance up to 60
DATA SHEET PART NO. : L-314YD REV : A / 4
PARA LIGHT ELECTRONICS CO., LTD. 4F, No.1, Lane 93, Chien Yi Road, Chung Ho City, Taipei, Taiwan, R.O.C. Tel: 886-2-2225-3733 Fax: 886-2-2225-4800 E-mail: para@para.com.tw http://www.para.com.tw DATA SHEET
Lumimicro 3528 One Chip Specification
Doc. No : LUMI 3528-2P- 05 08 17- SPEC 3528-2PIN-SMD LED White LED Customer Approval Model Issued Date LMFL2P35A1WHZ03 2005 08-17 Checked By Approved By Description SMD Type LED Written By Checked By Approved
DISCONTINUED (1998) FBR46 SERIES. MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) RoHS compliant FEATURES
MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) FBR46 SERIES RoHS compliant FEATURES Miniature size About 50% smaller in volume compared with the FBR240 series used mainly in communication equipment.
Advanced Monolithic Systems
Advanced Monolithic Systems FEATURES Three Terminal Adjustable or Fixed oltages* 1.5, 1.8, 2.5, 2.85, 3.3 and 5. Output Current of 1A Operates Down to 1 Dropout Line Regulation:.2% Max. Load Regulation:.4%
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) Rotor. Wiper. Cover. Pin S T - 2 T A 1 0 0 Ω ( 1 0 1 )
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) COPAL ELECTRONICS RoHS compliant INTERNAL STRUCTURE 8 4 7! 5! 9 FEATURES RoHS compliant Compact and low-profile mm single turn type Sealed construction 4 5 7
WCAP-CSGP Ceramic Capacitors
A Dimensions: [mm] B Recommended land pattern: [mm] D1 Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance 1±0.2 Vrms, 1 khz ±10% C 15000 pf ± 10% Rated voltage Dissipation factor
SECTION 13. Multipliers. Outline of Multiplier Design Process:
SECTION 13 Multipliers VMI manufactures many high voltage multipliers, most of which are custom designed for specific requirements. The following information provides general information and basic guidance
ST-2 SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) FEATURES PART NUMBER DESIGNATION S T - 2 T A 1 0 0 Ω ( 1 0 1 ) RoHS compliant
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) ST- RoHS compliant INTERNAL STRUCTURE 8 4 7 FEATURES RoHS compliant Compact and low-profile mm single turn type Sealed construction 4 5 7 8 9!! 5 Part name Housing
RoHS APPROVAL SHEET. ituner 12V/6.6A SERIES NO. (E17) EA10953A. ( ) Edac Power Electronics (Suzhou) Co., Ltd. 59 No.59, Chang Sheng Road, Sheng Pu,
APPROVAL SHEET CUSTOMER ituner CUSTOMER P/N DESCRIPTION EDAC MODEL 12V/6.6A SERIES NO. (E17) EA10953A DATE 2010-06-22 REVISION 0 APPROVED DESIGN PREPARE RoHS CONCLUSION APPROVED CONDITON CUSTOMER S APP
Specification MBT801-S
Specification MBT801S Drawn SSC Approval 고객명 Approval.com MBT801S 1. Features 2. Absolute Maximum Ratings 3. Electro Characteristics 4. Optical characteristics 5. Outline Dimension 6. Packing 7. Soldering
AC/DC Power Modules C B. TML Series, 20 & 40 Watt. Features. 20 Watt Models
TML Series, 0 & 0 Watt Features C B Scheme LVD UL 090- Encapsulated power supplies with increased power density Replaces TML and TML 0 series PCB mount or chassis mount with screw terminals Single, dual
Type EDL, Electric Double Layer Supercapacitors Ultra High Capacitance, Small Case Size Options
Ultra High Capacitance, Small Case Size Options Type EDL electric double layer supercapacitors offer extremely high capacitance values (farads) in a variety of packaging options that will satisfy, low
SPECIFICATION FOR APPROVAL. Approved by
C O N F I D E N T I A L D O C U M E N T SPECIFICATION FOR APPROVAL CONRAD Description : Royalohm Part no.: 0402WGxxxxxTCE (RMC 1/16W (0402) +/- 1%, 5% & Jumper) 0603SAxxxxxT5E (RMC 1/10W-S (0603) +/- 1%,
DYNACAP Double Layer Capacitor
DX Series (Terminal shaped V, H) Combines two coin cells using laser welding technology to obtain a rated voltage of 5.5V. Available in either vertical or horizontal terminal leads, they are 11.5 mm in
Interference Suppression Film Capacitors MKP Radial Potted Type
Interference Suppression Film Capacitors MKP Radial Potted Type FEATURES 7.5 mm to 27.5 mm lead pitch Supplied loose in box, taped on reel Material categorization: For definitions of compliance please
Operating Manual UWAPS-TINY Series
Operating Manual UWAPS-TINY Series Powecon Oy WWW.POWECON.FI 1/9 Table of content 1 Warranty...3 2 Safety information...3 3 Abbreviations and terminology...3 4 List of appendices...4 5 Introduction...4
Suntan Technology Company Limited. Application Guidelines For Tantalum Electroilytic Capacitors
For obtaining the most stable quality and sufficient Performance of the tantalum electrolytic capacitors,appropriate use must be made.before use,confirm the use conditions and rating performance of the
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC QUICK REFERENCE DATA DESCRIPTION VALUE Ceramic Class 1 2 Ceramic Dielectric U2J U2J Y5S, Y5U Y5S, Y5U Voltage (V AC ) 500 760
Capacitance Cap. Tol. Suffix construction. Rated voltage
Metallized Polypropylene Film Capacitors Type:ECWFE Plastic Film Capacitors Non-inductive construction using metalized Polypropylene film with flame retardant plastic case. Features Small size Excellent
Types MC and MCN Multilayer RF Capacitors
High-Frequency, High-Power, High-Voltage Chips with Nonmagnetic Option Rugged flexibility and compatibility with FR4 boards make Type MC and MCN capacitors ideal for use where other multilayer caps aren
Laser diffuse reflection light scanner with background suppression. Dimensioned drawing
Specifications and description HRTL 3B Laser diffuse reflection light scanner with background suppression Dimensioned drawing We reserve the right to make changes DS_HRTL3B_en.fm en 01-2010/12 50114049
Series AMEPR30-AZ up to 2.5A AC-DC / DC-DC LED Driver / Converter
FEATURES: Click on Series name for product info on aimtec.com Models Single output Model Max Output Power (W) 1 AC-DC Constant Current or Constant Over temperature protection Voltage LED Driver Over current
NI-ZN BATTERY SPECIFICATION
NI-ZN BATTERY SPECIFICATION 252000 Model Name: AA2500mWh(Ni-Zn) Issued Date: Sept. 2010 NICKEL ZINC BATTERY SPECIFICATION 1.APPLICATION The applicable range: This specification is available only for the
Metal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLN Series. MLN SurgeArray TM Suppressor. Description
MLN SurgeArray TM Suppressor RoHS Description The MLN SurgeArray Suppressor is designed to help protect components from transient voltages that exist at the circuit board level. This device provides four
063450 LI-POLYMER BATTERY PACKS. Specification. Type:063450 1000mAh. Prepared/Date Auditing/Date Approved/Date WANG MAR 16, 2006 LI MAR 16, 2006
063450 LI-POLYMER BATTERY PACKS Specification Type:063450 1000mAh Prepared/Date Auditing/Date Approved/Date WANG MAR 16, 2006 LI MAR 16, 2006 XIONG MAR 16, 2006 Sheet 1/5 1 Scope This product specification
LM138 LM338 5-Amp Adjustable Regulators
LM138 LM338 5-Amp Adjustable Regulators General Description The LM138 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 5A over a 1 2V to 32V output range
S P E C I F I C A T I O N F O R L I T H I U M B A T T E R Y. M o d e l : C R 2 0 3 2
S P E C I F I C A T I O N F O R L I T H I U M B A T T E R Y M o d e l : C R 2 0 3 2 Approved By Department Name Title Signature/Date (Remarks: The above table shall be filled by customer) POWER GLORY BATTERY
Single Output Switching Power Supply
.. RS- Code: CLP-A Single Output Switching Power Supply SPECIFICATION MODEL OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY EMC (Note 6) OTHERS NOTE DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER RIPPLE
30W Epistar 45mil Chip High Power LED
30W Epistar 45mil Chip High Power LED White:LEDE-P30-DH-White Warm White:LEDE-P30-DWH Features Long operating life Highest Luminous flux Wide range of colours:2500k-25000k Chip size: Epistar 45*45mil More
SELECTION GUIDE. Nominal Input
www.murata-ps.com NKE Series FEATURES RoHS Compliant Sub-Miniature SIP & DIP Styles 3kVDC Isolation UL Recognised Wide Temperature performance at full 1 Watt load, 40 C to 85 C Increased Power Density
Chrome DIN Rail Power Supply 24V 91.2W 1 Phase (Class II & NEC Class 2) / DRC-24V100W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage without power de-rating Efficiency > 87.0% @ 115Vac, > 89.0% @ 230Vac NEC Class
FP2 Relay. The Best Relaytion
The Best Relaytion 2 pole telecom / signal relay Through Hole Type (THT) Polarized. Relay types: non-latching with1 coil latching with 1 coil latching with 2 coils Features Telecom / signal relay (dry
Instruction Manual PFE300S 500S SERIES. TDK-Lambda PFE300S 500S Series INSTRUCTION MANUAL
PFE300S 500S SERIES Instruction Manual TDK-Lambda PFE300S 500S Series BEFORE USING THE POWER SUPPLY UNIT Be sure to read this instruction manual thoroughly before using this product. Pay attention to all
LED Module SPECIFICATION. LED Module for Modular Platform Series. LED Platform Module with Fin
DATE OF ISSUE : March, 2015 1/9 SPECIFICATION for Modular Platform Series Model Name Type Parts No. LED Platform Module with Fin CRI min. 70, 5000K, Flux Rank 3, Type Ⅱ-Short, 351Z Ceramic SL-P7R2E32SZWW
BM SERIES WAVE COMPACT 6.3 GHZ CW SERIES PULSE RADAR LEVEL INSTRUMENTS (6.3 GHz)
CW SERIES PULSE RADAR LEVEL INSTRUMENTS (6.3 GHz) DESCRIPTION The Radar Level Meters of BM COMPACT WAVE 6.3 GHz series are excellent devices for no contact level measurement. The microwave impulses, emitted
Spec. No. ICR18650-26C Version No. 0.0
1. Scope This product specification has been prepared to specify the rechargeable lithium-ion cell 2. Description and Model 2.1 Description Cell (lithium-ion rechargeable cell) 2.2 Model ICR18650-26C 3.
Contents. 12. Lot Number 10. 13. Reel Packing Structure 11. 14. Precaution for Use 13. 15. Hazard Substance Analysis 14. 16. Revision History 18
Rev : 00 ISSUE NO : DATE OF ISSUE : 2009. 04. 10 S P E C I F I CATION MODEL : SLHNNWW629T1S0U0S0 [Rank : (S0), (U0), (S0)] HIGH POWER LED - SUNNIX6 CUSTOMER : CUSTOMER CHECKED CHECKED APPROVED SAMSUNG
RT series Miniature Printed Circuit Board Relays, Sockets and Accessories
s RT series Miniature Printed Circuit oard Relays, Sockets and ccessories pplied Coil Voltage (% of rated nom.) RT series (DC Coil) 6 mp PC oard Miniature Relay Meets VDE 0mm Spacing, KV Dielectric File
High Ohmic/High Voltage Metal Film Leaded Resistors
, High Ohmic/High Voltage FEATURES Metal film technology High pulse loading (up to 10 kv) capability Small size (0207/0411) Compatible with lead (Pb)-free and lead containing soldering processes Compliant
No. STSE-CW2163B <Cat.No.031110> SPECIFICATIONS FOR NICHIA WHITE LED MODEL : NSPW315BS NICHIA CORPORATION -0-
No. STSE-CW2163B SPECIFICATIONS FOR NICHIA WHITE LED MODEL : NSPW315BS -0- 1.SPECIFICATIONS (1) Absolute Maximum Ratings (Ta=25 C) Item Symbol Absolute Maximum Rating Unit Forward Current IF 30 ma Pulse
Top Microsystems Proprietary Specification P/N: W090015HK-XP 022410RB-082709V.A0 SPECIFICATION
SPECIFICATION High Quality Switching Wallmount Adapter Interchangeable AC Plugs 90-264VAC Input 13.5W 9VDC 1.5A Output P/N: W090015HK-XP ** Specification Approval** This specification (total 11 pages including
Series AMLDL-Z Up to 1000mA LED Driver
FEATURES: Click on Series name for product info on aimtec.com Series Up to ma LED Driver Models Single output Model Input Voltage (V) Step Down DC/DC LED driver Operating Temperature range 4ºC to 85ºC
New XUY roller sensors
Do you want to simplify the sensor integration in your conveyor systems? New XUY roller sensors for packet, boxes, letters on roller conveyors. Telemecanique Sensor s OsiSense TM XUY photoelectric sensors
MAXIMUM LOAD CURRENT 1 A SN SERIES
SOLID STATE RELAY (I/O Module) MAXIMUM LOAD CURRENT 1 A SN SERIES RoHS compliant FEATURES I/O modules for interface between CPU and external input devices or loads Ultra slim and light weight, SIL s type
Precision Leaded Resistors
FEATURES Approved according to CECC 40101-806 Advanced thin film technology Low TC: ± 15 to Precision tolerance of value: ± 0.1 % and ± 0.25 % Superior overall : class 0.05 Wide precision range: 10 Ω to
Inductive Proximity Sensors
M12 Inductive Proximity Sensors Standard Length Mini's Extended Sensing 3 Wire DC 2 Wire DC 2 Wire AC (Wiring Schematic) 3 Wire DC PNP Normally Open (1) IMM32122C IMM35124C IMN32122C IMN35124C IMN32122M12
LM117 LM317A LM317 3-Terminal Adjustable Regulator
LM117 LM317A LM317 3-Terminal Adjustable Regulator General Description The LM117 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 1 5A over a 1 2V to 37V
AZ420 MINIATURE GENERAL PURPOSE RELAY
MINIATURE GENERAL PURPOSE RELAY FEATURES Rugged construction for high reliability Life expectancy greater than 0 million operations DC coils to 11 V Power consumption as low as 2 mw per pole available
INTEGRATED CIRCUITS DATA SHEET. TDA7000 FM radio circuit. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 May 1992 GENERAL DESCRIPTION The is a monolithic integrated circuit for mono FM portable radios, where a minimum on peripheral components
LM78XX Series Voltage Regulators
LM78XX Series Voltage Regulators General Description Connection Diagrams The LM78XX series of three terminal regulators is available with several fixed output voltages making them useful in a wide range
Pulse Withstanding Thick Film Chip Resistor-SMDP Series. official distributor of
Product: Pulse Withstanding Thick Film Chip Resistor-SMDP Series Size: /// official distributor of Pulse Withstanding Thick Film Chip Resistor-SMDP Series 1. Scope -This specification applies to ~ sizes
Chrome DIN Rail Power Supply 24V 30W 1 Phase (Class II & NEC Class 2) / DRC-24V30W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage without power de-rating Efficiency > 87.0% @ 115Vac & 230Vac NEC Class 2 / Limited
1. Scope This specification is applied to ICR18650. 2. Product Specification Table 1 No. Item Rated Performance Remark
1. Scope This specification is applied to ICR18650. 2. Product Specification Table 1 No. Item Rated Performance Remark 1 Rated Capacity Typical Minimum 2 Nominal Voltage 3.7V 3 Voltage at end of Discharge
LM1084 5A Low Dropout Positive Regulators
5A Low Dropout Positive Regulators General Description The LM1084 is a series of low dropout voltage positive regulators with a maximum dropout of 1.5 at 5A of load current. It has the same pin-out as
3 Thermal Transfer Acrylate Label Material 3921
3 Thermal Transfer Acrylate Label Material Technical Data April, 2008 Product Description 3M Thermal Transfer Acrylate Label Material consists of a non-topcoated acrylate facestock designed for thermal
Power chip resistor size 2512 PRC221 5%; 2% FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability.
FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability. APPLICATIONS Power supplies Printers Computers Battery chargers Automotive Converters CD-ROM. QUICK
Product Specification
Product Specification Model No.: DC-240-L01-00-TR Description: H=3.00mm Horizontal SMD DC Power Jacks Pin Shaft Diameter: 0.65mm Packing Method: Tape & Reel (600pcs./R) 1. General 1a. Scope The jacks should
HIGH VOLTAGE CERAMIC CAPACITORS
!Note Please read rating and!caution (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. C84E8.pdf 03.4.21 This catalog has only
ONE OF THE SMALLEST SNAP-ACTION SWITCHES IN THE WORLD. FEATURES Superminiature type, light-weight snap action switch PC board terminal type (0.
ONE OF THE SMALLEST SNAP-ACTION SWITCHES IN THE WORLD SWITCHES FEATURES Superminiature type, light-weight snap action switch PC board terminal type (0.2g) Solder terminal type with mounting holes (0.3g)
FRC Series 35mm Diameter Reflectors for SEOUL SEMICONDUCTOR A3 (Acriche) and P7LEDs
FRC Series 35mm Diameter Reflectors for SEOUL SEMICONDUCTOR A3 (Acriche) and P7LEDs High efficiency Faceted designs provide homogeneous focused spot and spilled/direct light 34.5 mm diameter for MR-11
Harvatek Surface Mount CHIP LED Data Sheet HT-380FCH-ZZZZ
Harvatek Surface Mount CHIP LED Data Sheet Official Product HT Part No. Customer Part No. Data Sheet No. Tentative Product **************** **************** May. 14, 2007 Version of 1.1 Page 1/15 DISCLAIMER...
PART NO.: L-C150SRCT REV: A / 4
PARA LIGHT ELECTRONICS CO., LTD. 4F, No.1, Lane 93, Chien Yi Road, Chung Ho City, Taipei, Taiwan, R.O.C. Tel: 886-2-2225-3733 Fax: 886-2-2225-4800 E-mail: para@para.com.tw http://www.para.com.tw DATA SHEET
Cree XLamp MX-3S LEDs Data Sheet
Cree XLamp MX-3S LEDs Data Sheet The Cree XLamp MX-3S LED provides the proven lighting-class performance and reliability of Cree XLamp LEDs in a high voltage, PLCC configuration. All members of the MX-family
Data Sheets of AVA Technology SMD Type White LED. Model : T5050. AVA Technology Co.
Data Sheets of AVA Technology SMD Type White LED Model : AVA Technology Co. 2640 S. Myrtle Ave. Suite 6 Monrovia, CA 91016 P: 626-574-7726 F: 626-574-7732 http://www.led4light.com Top View LED with Reflector
Specification of 5 Wire Analog Touch Panel
Specification of 5 Wire Analog Touch Panel 5 WIRE ANALOG RESISTIVE TOUCH PANEL A. Application This specification applies to the 5 Wire Analog Resistive Touch Panel. B. Environmental Conditions 1. Operating
% ^ ) 0.55 W Low Power Solenoid Valves Aluminum, Brass, or Stainless Steel Bodies 1/4" to 1" NPT. 2/2 3/2 4/2 5/2 5/3 SERIES Low Power
.55 W Solenoid Valves Aluminum, Brass, or Stainless Steel Bodies /" to " NPT / 3/ / 5/ 5/3 Features Molded one-piece solenoid with highly efficient solenoid cartridge and.55 W low wattage coil Standard
Schottky Rectifier, 1.0 A
Schottky Rectifier, 1.0 A VS-BQ040-M3 Cathode Anode PRODUCT SUMMARY Package SMB I F(AV) 1.0 A V R 40 V V F at I F 0.38 V I RM 9 ma at 125 C T J max. 150 C Diode variation Single die E AS 3.0 mj FEATURES
EMIT-3020L. Tel: 03-3980-2212. Analog Telephony / Modem Couplers DESCRIPTION. NOMENCLATURE (Fig. 1) MECHANICAL DIMENSIONS (Fig. 2)
EMIT-2L DESCRIPTION The REMtech Magnetics EMIT-2L is a Dry Encapsulated Modem Isolation Transformer suitable for up to V.9 (6 kbps) consumer and internet analog modem applications compliant with International
DATA SHEET. TDA1518BQ 24 W BTL or 2 x 12 watt stereo car radio power amplifier INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 July 1994 GENERAL DESCRIPTION The is an integrated class-b output amplifier in a 13-lead single-in-line (SIL) plastic power package.
Thick Film Resistor Networks, Military, MIL-PRF-83401 Qualified, Type RZ010 and RZ020 Dual-In-Line, Molded DIP
MDM (Military M831/1 and /2) Thick Film Resistor Networks, Military, MIL-PRF-831 Qualified, Type RZ1 and RZ2 Dual-In-Line, Molded DIP STANDARD ELECTRICAL SPECIFICATIONS VISHAY DALE MODEL/ PIN NO. MIL STYLE
UL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming
Features Regulated Converters Selection Guide UL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit Protected Pinned
Lithium Ion Battery Specifications
Lithium Ion Battery Specifications Type: Cylindrical Lithium Iron Phosphate Battery Mode: LFP-26650-3300 AA Portable Power Corp. Prepared by Checked by Approved by 1 . Product Specifications Type ------------