SCREEN ROOM ITM./ART MODEL#L-GZ938PCO-B/L-GZ938PCO-B2 ASSEMBLY INSTRUCTIONS
|
|
- Amanda Andrews
- 7 years ago
- Views:
Transcription
1 SCREEN ROOM ITM./ART MODEL#L-GZ938PCO-B/L-GZ938PCO-B2 ASSEMBLY INSTRUCTIONS IMPORTANT: RETAIN FOR FUTURE REFERENCE. READ CAREFULLY. Please check with your local governing authority / local municipal codes regarding installation of structures before assembly. Tools required (not included): Phillips screwdriver, 2 ladders, cordless drill, metric socket and carpenter s level. WARNING: Check to ensure all parts are present prior to assembly. This unit is heavy! At least 2 adults are needed for safe assembly ---- Never assemble this alone! Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the area of the gazebo construction. Keep assembly area more than 1.8 m / 5.9 ft / 5.9 pi from any obstruction such as fence, garage, and house, overhanging branches, laundry line or electrical wires. Some parts may contain sharp edges. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to the product. Please read all instructions before assembly and use. For outdoor use only. Check all bolts for tightness before use and periodically check and tighten bolts as necessary. Assemble this unit on firm, level ground or hard surface only. Ensure the unit is level after final assembly. Protect parts during assembly by laying them on a non-abrasive surface such as blankets or cardboard. DO NOT REMOVE THE PROTECTIVE FILM ON THE POLYCARBONATE ROOF PANELS UNTIL INSTALLATION. MAKE SURE TO PUT THE UV PROTECTED SIDE FACING UP. IT IS A VERY IMPORTANT PROCEDURE, IF NOT FOLLOWED AS DESCRIBED. YOUR ROOF WILL NOT BE COVERED BY THE GUARANTEE. IMPORTANT Please do not return this product to the store. For technical assistance or replacement parts call Sunjoy from 8:00 AM Eastern time to 8:00 PM Pacific time at the following: (English, French & Spanish in US) or service@ferro-works.com.
2 Parts List DESCRIPTION PART # QTY LINE DRAWING OF PART Slide rail 1 (long, lower left) A1 2 Slide rail 2 (long, lower right) A2 2 Slide rail 3 (short, lower left) A3 2 Slide rail 4 (short, lower right) A4 2 Connector 1 A5 4 Post B 4 Wall screen 1 (left) C1 4 Wall screen 2 (right) C2 4 Gutter 1 (long, left) D1 2 Gutter 2 (long, right) D2 2 Gutter 3 (short, left) D3 2 Gutter 4 (short, right) D4 2 Connector 2 D5 4 Connector (corner) E 4 Movable door 1 (long, left) F1 2 Movable door 2 (long, right) F2 2 Movable door 3 (short, left) G1 2 Movable door 4 (short, right) G2 2 Wheels H 16
3 DESCRIPTION PART # QTY LINE DRAWING OF PART Rail track 1 (long, upper left) I1 2 Rail track 2 (long, upper right) Rail track 3 (short, upper left) Rail track 4 (short, upper right) I2 2 I3 2 I4 2 Rail block slice I5 4 Connector 3 J1 6 Connector 4 J2 4 Bracket 1 (long, left) K1 2 Bracket 2 (long, right) K2 2 Bracket 3 (short, left) K3 2 Bracket 4 (short, right) K4 2 Connector 5 (roof) L 1 Bar 1 (corner) M1 4 Bar 2 (middle) M2 6 Hook N 1 PC Panel 1 (left) O1 4 PC Panel 2 (right) O2 4 PC Panel 3 (middle) O3 2 Steel panel 1 (left) O4 4 Steel panel 2 (right) O5 4 Steel panel 3 (middle) O6 2
4 DESCRIPTION PART # QTY LINE DRAWING OF PART Roof P 1 Beam 1 (outside, lower left corner) Beam 2 (outside, lower right corner) Beam 3 (outside, lower left middle) Beam 4 (outside, lower right middle) Q1 4 Q2 4 Q3 6 Q4 6 Decorative groove connector R 4 Bar 3 (short, Left) S1 4 Bar 4 (short, right) S2 4 Bar 5 (short, middle) S3 2 Connector 6 (left) T1 4 Connector 7 (right) T2 4 Connector 8 (middle) T3 2 Hardware Packet for Step 1 PART # DESCRIPTION QTY LINE DRAWING AA M6 x 15mm bolt 56 PCS BB M6 washer 96 PCS CC M6 x 25mm bolt 8 PCS DD M6 x 35mm bolt 16 PCS EE M6 x 55mm bolt 16 PCS Z1 M6 wrench 2 PCS
5 Out Out Fig.1: Insert the side with label Out of Wall screen 1 (left) (C1) into the bottom slot of Post (B). (Note: Label Out should be on outside). Repeat this step for the 3 remaining Wall screens 1 (left) (C1) and all Wall screens 2 (right) (C2). Fig.2: Connect Slide rail 1 (long, lower left) (A1) and Slide rail 2 (long, lower right) (A2) to connector 1 (A5) using M6 x 15 mm bolts (AA) and M6 washers (BB). Repeat this step for Slide rail 3 (short, lower left) (A3) and Slide rail 4 (short, lower right) (A4). Fig.3: Attach Slide rail 1 (long, lower left) (A1) to Wall screen 1 (left) (C1) and Wall screens 2 (right) (C2) using M6 x 35 mm bolts (DD) and M6 washers (BB). Repeat this step for Slide rail 2 (long, lower right) (A2), Slide rail 3 (short, lower left) (A3) and Slide rail 4 (short, lower right) (A4). Fig.4: Attach Slide rail 1 (long, lower left) (A1) to Post (B) using M6 x 25 mm bolts (CC) and M6 washers (BB). Repeat this step for Slide rail 2 (long, lower right) (A2), Slide rail 3 (short, lower left) (A3) and Slide rail 4 (short, lower right) (A4). Fig.5-1: Connect Gutter1 (long, left) (D1) and Gutter 2 (long, right) (D2) to connector 2 (D5) using M6 x 15 mm bolts (AA) and M6 washers (BB). Fig.5-2: Connect Gutter 3 (short, left) (D3) and Gutter 4 (short, right) (D4) to connector 2 (D5) using M6 x 15 mm bolts (AA) and M6 washers (BB). Fig.6: Attach assembled Gutter1 (long, left) (D1) and Gutter 2 (long, right) (D2) to Wall screens 1 (left) (C1) and all Wall screens 2 (right) (C2) using M6 x 55 mm bolts (EE) and M6 washers (BB). Repeat this step for assembled Gutter 3 (short, left) (D3) and Gutter 4 (short, right) (D4). Please pay attention to the connection where the arrow is pointing in above fig. 7, as these parts when assembled should be flat after assembly.
6 Fig.7-1: Attach Connector 3 (J1) to assembled Gutter 3 (short, left) (D3) and Gutter 4 (short, right) (D4) using M6 x 15 mm bolts (AA) and M6 washers (BB). Fig.7-2: Attach Connector 3 (J1) to assembled Gutter1 (long, left) (D1) and Gutter 2 (long, right) (D2) using M6 x 15 mm bolts (AA) and M6 washers (BB). Fig.8: Attach Connector 4 (J2) to each corner of screen room using M6 x 15 mm bolts (AA) and M6 washers (BB). Hardware Pack for Step 2 PART # DESCRIPTION QTY LINE DRAWING AA M6 x 15mm bolt 32 PCS BB M6 washer 42 PCS CC M6 x 25mm bolt 10PCS Fig.9: When assembling step 2, 2 people and 2 ladders are required. (It is same for assembling Bar 2 (middle) (M2)) Fig.9-1: Attach the top of Bar 1 (corner) (M1) to Connector 5 (roof) (L) using M6 x 15 mm bolts (AA) and M6 washers (BB). Fig.10: Attach the bottom of Bar 1 (corner) (M1) to Connector 4 (J2) using M6 x 15 mm bolts (AA) and M6 washers (BB). Fig.11: Attach the top of Bar 2 (middle) (M2) to Connector 5 (roof) (L) using M6 x 15 mm bolts (AA) and M6 washers (BB).
7 Fig.12: Attach the bottom of Bar 2 (middle) (M2) to Connector 3 (J1) using M6 x 15 mm bolts (AA) and M6 washers (BB). Fig.13: Attach Roof (P) to Connector 5 (roof) (L) using M6 x 15 mm bolts (AA) and M6 washers (BB). Secure Hook (L) to Connector 5 (roof) (L). Fig.14: Attach Bar 5 (short, middle) (S3) and Bar 3 (short, left) (S1) to Bar 2 (middle) (M2) using M6 x 25 mm bolts (CC) and M6 washers (BB). Repeat this step on opposite side (Note: This step needs 2 people to assemble) Fig.15: Attach Bar 3 (short, left) (S1) and Bar 4 (short, right) (S2) to Bar 1 (corner) (M1) using M6 x 25 mm bolts (CC) and M6 washers (BB). Repeat on opposite side (Note: This step needs 2 people to assemble) Hardware Pack for Step 3 PART # DESCRIPTION QTY LINE DRAWING AA M6 x 15mm bolt 34 PCS BB M6 washer 38 PCS FF M6 x 45mm bolt 4 PCS
8 Fig.16: Slide PC panel 1 (left) (O1) into the top section created by Bar 1 (corner) (M1) and Bar 2 (middle) (M2). Repeat this step for PC panel 2 (right) (O2) and PC panel 3 (middle) (O3). Repeat for opposite side. Once the polycarbonate panels are installed, remove the protective film. Fig.17: Insert Connector 6 (left) (T1) into the slot created by Bar 1 (corner) (M1) and Bar 2 (middle) (M2). Repeat this step for Connector 7 (right) (T2) and Connector 8 (middle) (T3). Fig.18: Insert Steel panel 1 (left) (O4) into the slot created by Bar 1 (corner) (M1) and Bar 2 (middle) (M2). Repeat this step for Steel panel 2 (right) (O5) and Steel panel 3 (middle) (O6). Repeat for opposite side. Fig.19: Attach Beam 2 (outside, lower right corner) (Q2) to Connector 4 (J2) using M6 x 15 mm bolts (AA) and M6 washers (BB) to secure Steel panel 1 (left) (O4). Repeat this step for Beam 1 (outside, lower left corner) (Q1) to Connector 4 (J2) using M6 x 15 mm bolts (AA) and M6 washers (BB) to secure Steel panel 2 (right) (O5). Fig.20: Attach Beam 3 (outside, lower left middle) (Q3) to Connector 3 (J1) using M6 x 15 mm bolts (AA) and M6 washers (BB) to secure Steel panel 1 (left) (O4). Repeat this step on Q4, J1 and O6 assembly. Fig.21: Hang Bracket 1 (long, left) (K1), Bracket 2 (long, right) (K2), Bracket 3 (short, left) (K3), Bracket 4 (short, right) (K4) onto Gutter 1 (long, left) (D1), Gutter 2 (long, right) (D2), Gutter 3 (short, left) (D3) and Gutter 4 (short, right) (D4) as per above fig. Fig.22-1: Attach Bracket 1 (long, left) (K1) and Bracket 2 (long, right) (K2) to Bar 2 (middle) (M2) using M6 x 15 mm bolts (AA) and M6 washers Fig.22-2: Attach Bracket 4 (short, right) (K4) to Bar 2 (middle) (M2) using M6 x 15 mm bolts (AA) and M6 washers (BB). Fig.23: Connect Bracket 3 (short, left) (K3) and Bracket 4 (short, right) (K4) to Decorative groove connector (R) using M6 x 15 mm bolts (AA) and M6 washers (BB). Repeat this step for connecting Bracket 1 (long, left) (K1) and Bracket 2 (long, right) (K2). Fig.24: Attach Connector (corner) (E) to the top of Post (B). Then secure it to each corner formed by Bracket 1 (long, left) (K1), Bracket 2 (long, right) (K2), Bracket 3 (short, left) (K3), Bracket 4 (short, right) (K4) using M6 x 45 mm bolts (FF) and M6 washers (BB).
9 Hardware Pack for Step 4 PART # DESCRIPTION QTY LINE DRAWING AA M6 x 15mm bolt 32 PCS BB M6 washer 32 PCS GG M5 x 15 mm bolt 32 PCS II Φ8 x 260 stake 12 PCS Fig.25: Attach Wheels (H) to Movable door 1 (long, left) (F1), Movable door 2 (long, right) (F2), Movable door 3 (short, left) (G1) and Movable door 4 (short, right) (G2) using M5 x 15 mm bolts (GG). Fig.26: Attach Rail track 2 (long, upper right) (I2) to Movable door 2 (long, right) (F2) through Wheel (H) as per above fig. Repeat this step for Rail track 4 (short, upper right) (I4) to Movable door 4 (short, right) (G2). (Note: The door with IN label should face inside) Fig.27: Put the wheel at the bottom of Movable door 2 (long, right) (F2) into Slide rail 2 (long, lower right) (A2). Repeat this step for Movable door 4 (short, right) (G2) to Slide rail 4 (short, lower right) (A4). (Note: The screen toward inside) Fig.28: Attach Rail track 2 (long, upper right) (I2) to Gutter 2 (long, right) (D2) using M6 x 15 mm bolts (AA) and M6 washers (BB). Repeat this step for attaching Rail track 4 (short, upper right) (I4) to Gutter 4 (short, right) (D4).
10 IN Fig.29: Attach Rail track 1 (long, upper left) (I1) to Movable door 1 (long, left) (F1) through Wheel (H) as per above fig. Repeat this step for Rail track 3 (short, upper left) (I3) to Movable door 3 (short, left) (G1). (Note: The door with IN label should face inside) Fig.30: Put the wheel at the bottom of Movable door 1 (long, left) (F1) into Slide rail 1 (long, lower left) (A1). Repeat this step for Movable door 3 (short, left) (G1) to Slide rail 3 (short, lower left) (A3). (Note: The screen toward inside) Fig.31: Insert Rail track 1 (long, upper left) (I1) to Rail track 2 (long, upper right) (I2). Repeat this step for Rail track 3 (short, upper left) (I3) and Rail track 4 (short, upper right) (I4). Fig.32: Attach Rail track 1 (long, upper left) (I1) to Gutter 1 (long, left) (D1) using M6 x 15 mm bolts (AA) and M6 washers (BB). Repeat this step for Rail track 3 (short, upper left) (I3) to Gutter 3 (short, left) (D3). Fig.33: Attach Rail block slice (I5) to the corner created by Rail track 1 (long, upper left) (I1), Rail track 2 (long, upper right) (I2), Rail track 3 (short, upper left) (I3) and Rail track 4 (short, upper right) (I4) using M6 x 15 mm bolts (AA) and M6 washers (BB). Fig.34: Secure the assembled screen room to the ground usingφ8 x 260 stakes (II). CARE INSTRUCTIONS Clean gently with a sponge using environmentally-friendly soap and water solution. Do not use abrasive materials, such as wire brushes, chemicals, cleansers or bleach. Do not use a pressure washer. Rinse well. Allow to air dry. If there are nicks, chips or scratches, go to your local hardware store or home center and obtain a closest match touch-up paint suitable for outdoor metal use. Follow instructions that appear on the paint can. SPECIFICATIONS: Resists winds up to 37 mph (59.5 km/h) when firmly anchored using stakes to the ground. Resists winds up to 45.6 mph (73.4km/h) when firmly anchored using expansion bolts into a suitable concrete base. Roof can withstand up to 620 kg / 1364 lbs weight load. Maximum load for the center hook: 15 kg / 33 lbs. MADE IN CHINA E
Assembly Manual L-GZ340PST-3D
Assembly Manual L-GZ30PST-3D Stop Please read and understand this manual before proceeding with assembly. Before beginning assembly of product, make sure all parts are present. Compare parts with package
More information10'X12' Monterey gazebo instruction manual Item #: L-GZ215PST-4 SKU #: 210019492
10'X12' Monterey gazebo instruction manual Item #: L-GZ215PST-4 SKU #: 210019492 IMPORTANT: Please read and follow all safety statements, warnings, assembly instructions, use & care directions before attempting
More informationGarden Oasis BAY WINDOW GAZEBO SEARS ITEM # 80164. Warning:
Garden Oasis BY WINDOW GZBO SRS ITM # 806 Warning:. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.
More informationBUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS
BUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationAssembly Instructions. Item: L-GZ660PST
Assembly Instructions Item: L-GZ660PST IMPORTANT: Please read and follow all safety statements, warnings, assembly instructions, use & care directions before attempting to assemble. 1. When installing
More informationCHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS
CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationChelsea Loft Bed WARNING:
Chelsea Loft Bed WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS FOR FUTURE
More informationWhalen Furniture Mfg. Inc. Factory No. 43-11696 Page # 1
ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS, SHARP POINTS, SHARP EDGES If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationLunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide
Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your
More informationItem #: BTOL Assembly Instructions
Item #: BTOL Assembly Instructions For our most current instructions, to request missing, lost or broken parts, or for any other Customer Service issues, please visit our website at www.walkeredison.com
More informationGreenhouse Assembly Instructions
Greenhouse Assembly Instructions 6 x 1.93m) 6 x 8 GREENHOUSE 01 ASSEMBLY INSTRUCTIONS 6 x 6 GREENHOUSE 02 ASSEMBLY INSTRUCTIONS 6 x 4 GREENHOUSE 03 ASSEMBLY INSTRUCTIONS 6ft (1.93m x 1.9 Introduction Safety
More informationpottery barn kids MADELINE BUNK BED
pottery barn kids MADELINE BUNK BED! WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. To help prevent serious or fatal injuries from entrapment
More informationHow to Install UnderDeck The Original.
How to Install UnderDeck The Original. TOOLS: Chalk Line Caulk Gun Garden hose or water bucket Gloves Hammer or Screw Gun Power Mitre Saw with OSB Blade Pencil Pliers Safety Glasses Straight Edge / Carpenter
More informationHow To Make A Thomas Bunk Bed
pottery barn kids THOMAS BUNK BED WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS
More informationIn-Ground Basketball System Owners Manual
In-Ground Basketball System Owners Manual Customer Service Center N53 W4700 South Corporate Circle Sussex, WI 53089 U.S.A. Write Model Number From Box Here: WARNING! 3 Capable Adults REQUIRED TOOLS AND
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationAssembly Instructions
CK622400TX- Espresso CK612400TX- Black Nailhead Cocktail Table Trunk Assembly Instructions For assistance with assembly contact: Southern Enterprises Inc. Customer Service 1-800-633-5096 service@seidal.com
More information758 Heavy-duty Ratchet Guy Wire Cutter
INSTRUCTION MANUAL 758 Heavy-duty Ratchet Guy Wire Cutter Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179
More informationMODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER
MODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER IMPORTANT INSTRUCTIONS: : Read all instructions carefully & completely to become familiar with parts, assembly, safety and proper use of this product.
More information10 ft x 20 ft / 3 m x 6 m STEEL FRAME CAR CANOPY
10 ft x 20 ft / 3 m x 6 m STEEL FRAME CAR CANOPY Instruction Manual ITM./ART.496840 VIEW ASSEMBLY VIDEO AND INSTRUCTION MANUAL AT www.zhengteusa.com Before assembly, read these instructions carefully.
More informationBUNK BED. Model No.: DA3797E - Espresso DA3797P- Pine. UPC CODE: 0-65857-16117-5 (Espresso) 0-65857-16116-8 (Pine) NOTE: Lot number: Date of purchase:
BUNK BED Model No.: DA3797E - Espresso DA3797P- Pine UPC CODE: 0-65857-16117-5 (Espresso) 0-65857-16116-8 (Pine) NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS Instruction Booklet 18 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE
More informationMBSAW. Meat Cutting Band Saw With Meat Grinder Assembly & Operating Instructions
06/2011 MBSAW Meat Cutting Band Saw With Meat Grinder Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper
More informationCeiling Mounted Folding Attic Ladders Installation Instructions
Ceiling Mounted Folding Attic Ladders Installation Instructions WARNING Before you start installing your new Louisville Ceiling Mounted Folding Attic Ladder, you must read and understand the following:
More informationT360 Barbecue. Assembly Manual. 85-3052-6 (G30531) Propane 1 YEAR LIMITED WARRANTY
T360 Barbecue Assembly Manual 85-3052-6 (G30531) Propane 1 YEAR LIMITED WARRANTY READ AND SAVE MANUAL FOR FUTURE REFERENCE. If pre-assembled, leave this manual with unit for consumer s future reference.
More informationSeismic Installation for Attic Storage System
Your Performance Partner Seismic Installation for Storage System CONTENTS SSafety Precautions................................. 2 Required Tools..................................... 2 Parts and Fastener
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual
More information8' W x 8' H or 10' H Peak Style Shelter Assembly Instructions
' W x ' H or ' H Peak Style Shelter Assembly Instructions Description ' x ' x ' Peak Style Shelter - Gray ' x ' x ' Peak Style Shelter - Gray Recommended Tools Please read instructions COMPLETELY before
More informationBeadboard Wall Bookcase
Beadboard Wall Bookcase Note: The maximum load for each shelf is 30lbs.This hanging system is meant for drywall/wood stud mounting only. If walls are concrete, brick or plaster, please consult your local
More informationTriple Threat 3-in-1 Game Table 3 IN 1 GAME TABLE
NG0M Triple Threat 3-in- Game Table 3 IN GAME TABLE Thank 3 in Y Game Table Thank you for your purchase of our product. We work around the clock and around the globe to ensure that our products maintain
More informationCONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER CONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL Model CCX-AG Note: 40 lbs. of sand required!
More informationENIGMA-X SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS
ENIGMA-X SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationATS Overhead Table Shelf System INSTRUCTION MANUAL
ATS Overhead Table Shelf System INSTRUCTION MANUAL ATS Overhead Table Shelf System Instruction Manual Warranty Newport Corporation warrants this product to be free of defects in material and workmanship
More informationAssembly and Usage Instructions
Assembly and Usage Instructions A Product 5885 West Van Horn Tavern Road Columbia, MO 65203 www.caldwellshooting.com Instruction #1001667 Limited Warranty Every Caldwell product is warrantied to be free
More informationNBA Arena Portable System
REQUIRED TOOLS AND MATERIALS: Two (2) Capable Adults Tape Measure Wood Board 6 x 6 (scrap) N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. NBA Arena Portable System Sawhorse or Support Table
More informationCisco Aironet 2.4-GHz MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2440NV-R)
Cisco Aironet 2.4-GHz MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2440NV-R) This document outlines the specifications for the Cisco Aironet 2.4-GHz MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2440NV-R)
More informationWARNING: Important: Keep these instructions for future reference. Gate Instructions (1) Assembly and Installation Instructions
Assembly and Installation Instructions Please read these instructions carefully. Please follow these instructions carefully to ensure that your gate extension is properly installed. Improper installation
More informationSTEEL-RITE II or III COMMERCIAL SECTIONAL DOOR Owner s Manual Supplement Model 52242 NOTICE TO USER
STEEL-RITE II or III COMMERCIAL SECTIONAL DOOR Owner s Manual Supplement Model 52242 NOTICE TO USER Thank you for purchasing the Steel-Rite II or III, model 52242 commercial sectional door from RITE-HITE
More informationTONNEAU INSTALLATION GUIDE
TONNEAU INSTALLATION GUIDE Warranty, Care & Maintenance Model 4056 Toyota Tacoma Double Cab 5' Short Bed 2005-Current (With Multi-Track System) EASY AS 1-2-3! NORMAL INSTALLATION TIME 30 MINUTES For Warranty
More informationConvertible Crib and Changer (M668)
Model No.: M668 PO #: Serial #: Convertible Crib and Changer (M668) THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. If you have any questions or missing parts, please contact us. DO NOT
More informationVISION SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS
VISION SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationHOME GYM. Model. Retain This Manual for Reference OWNER'S MANUAL. www.hyper-extension.com
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice www.hyper-extension.com HOME GYM 50036 Hardware Identifier Assembly Instruction Parts List Warranty
More informationAwning Instructions. Standard Manual 1.5m to 4.5m
Awning Instructions Standard Manual 1.5m to 4.5m English Standard Manual Instructions Contents Warning 1.5m 3.0m Awnings 4 x Expansion bolts (2 per bracket)** 2 x brackets 1 x Awning 1 x Winder handle
More informationCustomer Service 800.780.8889 or visit us online at smithnoble.com. Wood Shutters. Step by Step Installation. Troubleshooting Tips
reflect your style TM Customer Service 800.780.8889 or visit us online at smithnoble.com Wood Shutters Step by Step Installation Troubleshooting Tips Easy Care Instructions STEP 1 Your New Shutter Thank
More informationRoll-Up Door Maintenance Guide
R Roll-Up Door Maintenance Guide Cable Replacement on Two Spring Type Balancer Page 1 Panel Replacement - Removable Roller Cover Type Bottom Panel Page 1 Panel Replacement - Removable Roller Cover Type
More informationSamuel Shorty Bunk Bed
Samuel Shorty unk ed - Please keep for future reference / 88/999 0/8 IMPORTANT NOTE: The top surface of the mattress should not come above this line. imensions Width - 8cm epth - 8cm eight - 0cm IMPORTANT
More informationInstallation Instructions Avalanche XUV Cap IMPORTANT! IMPORTANT!
Installation Instructions Avalanche XUV Cap IMPORTANT! Read all instructions carefully before commencing any work. Always wear safety equipment. Some installation steps will require two or more installers.
More informationFitting Instructions Garador, Westland & Catnic Garage Door Spring Box Roller Wheels & Wall Bracket & Link Arm
Fitting Instructions for a Garador, Westland & Catnic Garage Door Spring Box Roller Wheels & Wall Bracket & Link Arm These instructions cover, how to replace a Spring Box Assembly to a Garador, Westland
More informationBasic Spring Motor Roller Shades
Comprehensive Roller Shade Installation Guide Basic Spring Motor Roller Shades ATTENTION!!! READ CAREFULLY! This shade has a reliable long-lasting Spring Motor. The Spring Motor must have proper tension
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationINSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR
INSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR (For NEW 2007 ALL WHITE KWIK-KITS ONLY) Warning do not attempt to install A/C units unless you are experienced with servicing
More informationDestiny Shower Enclosure Installation Instructions
Destiny Shower Enclosure Installation Instructions IMPORTANT Please read carefully the following instructions before installing your shower enclosure. If you have any questions on this shower enclosure
More informationINSTALLATION INSTRUCTIONS for Bifold Doors (JII103)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast
More informationUninterruptible Power Supply. 500 kva - 750 kva
9 315 Uninterruptible Power Supply 500 kva - 750 kva T1 and T3 Installation Addendum 164201244-001 Rev. A ------------------------------------------------------------------------ ------------------------------------------------------------------------
More informationPowerFlex 700S and 700H Frame 12 DC Bus Connector Kit
PowerFlex 700S and 700H Frame 12 DC Bus Connector Kit Installation Instructions This document provides instructions for the installation of a DC bus connector kit for PowerFlex 700S and 700H frame 12 drives
More informationFront Panel Board Cable Replacement Instructions
apple Mac Pro Front Panel Board Cable Replacement Instructions First Steps 1 Shut down computer. Note: Follow these instructions carefully. Failure to do so could damage your equipment and void its warranty.
More information149mm. Walk-Thru Assembly Gate. MODEL NO: 1161, 1167 Owner s Manual. www.regalo-baby.com
149mm 210mm Walk-Thru Assembly Gate MODEL NO: 1161, 1167 Owner s Manual READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE USE. www.regalo-baby.com... Regalo International,
More informationHALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL
HALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL Please read these instructions carefully and completely before attempting to install Hale Pet Doors; they will guide you through the steps
More informationTable of Contents. Safety... 3 Specifications... 4 Assembly... 5. Maintenance... 29 Warranty... 32 Parts Lists... 30
Table of Contents Safety... 3 Specifications... 4 Assembly... 5 Maintenance... 29 Warranty... 32 Parts Lists... 30 WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you
More informationAMF112 Instruction Manual
AMF112 Instruction Manual Scan here to view product demo and install videos or visit san.us/103 Milestone AV Technologies 6436 City West Parkway Eden Prairie, MN 55344 USA Customer Service Americas: 800-359-5520
More informationTENSION ISSUES? ROLLER SEE PAGE 7
ROLLER TENSION ISSUES? SEE PAGE 7 Roller Shade Installation Guide Important: If you have ordered a valance for your shade, you must first read the Valance Installation Guide found in your box. We make
More informationTools Required. Recommended Adhesives Vinyl Bonding: - Christy s White Hot Vinyl Cement
Assembly Instructions STEP-BY-STEP HANDRAIL INSTALLATION for 1-1/2" vinyl handrail component system Rise in inches Run in inches 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 8.5 47 45 43 42 40
More informationGreenWay Solar LED Path and Trail Lighting System. Installation and Owner s Manual
GreenWay Solar LED Path and Trail Lighting System Installation and Owner s Manual Important Notes and Warnings This installation and instruction manual provides installation, operation, and maintenance
More informationReplacement Instructions. Warning: During this procedure, keep small parts away from children.
apple ibook G4 Memory Card Replacement Instructions Follow the instructions in this sheet carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note: Written
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More informationESTATE WAGON MODEL 300 OWNER MANUAL
ESTATE WAGON MODEL 300 OWNER MANUAL Country Manufacturing, Inc. P.O. Box 104 Fredericktown, OH 43019 PH: 740-694-9926 FAX: 740-694-5088 I. INTRODUCTION The Model 300 Four Wheeled Wagon (ESTATE VERSATILITY
More information9,000lb capacity 4 Post Lift Installation Manual
9,000lb capacity 4 Post Lift Installation Manual Parts Checklist 1 Main side track with 9/16 hole on cylinder end complete with cylinder, hose and connector 1 Offside track 2 Cross Rails pre-assembled
More informationINFINITY-Z SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS
INFINITY-Z SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationINSTALLATION MANUAL. Contents JAPANESE ENGLISH GERMAN FRENCH ITALIAN SPANISH. To the installing technician: CEILING BRACKET
Be sure to read this installation manual thoroughly prior to installation. If installation methods or non-standard parts not specified in this installation manual are used, accidents or injury may result.
More informationSTEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13
STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 (See Supplemental Instructions for trailers with heavy duty round footplates and/or Power Leveling Systems) PHONE SUPPORT
More informationAMF112 (6904-002010 <00>) 13mm (1/2 in.)
AMF112 () Concrete Wood 13mm (1/2 in.) 5.5mm (7/32 in.) 10mm (3/8 in.) Sanus Systems 2221 Hwy 36 West Saint Paul, MN 55113 USA Customer Service Americas: 800-359-5520 651-484-7988 info@sanus.com Europe,
More informationCable Drum Installation
20 Cable Drum Installation COUNTERBALANCE None Shake the TorqueMaster spring tube gently to extend the winding shafts out about 5" on each side. For single spring applications, there will be no left hand
More informationOAK WORKBENCH WITH 2 DRAWERS
OAK WORKBENCH WITH 2 DRAWERS Model 93991 ASSEMBLY Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.
More informationHORIZONTAL INSTALLATION
THERMO/SOLAR Žiar s.r.o. MANUAL FOR INSTALLATION PV SUPPORTING FRAMES HORIZONTAL INSTALLATION Technical alternation reserved A1410 1 12/2014 CONTENT ORD.NO. PAGE Mounting information 3 Mounting, flat roof
More informationInstallation Instructions:
Portable Guardrail System Model Numbers: 7900060, 7900061, 7900062, 7900063 Installation Instructions: Portable Guardrail System This instruction is intended to meet the Manufacturer s Instructions requirement
More informationPage 2 of 6. Fittings Checklist. Care & Maintenance. Additional Tools Required. General Hints & Tips When
MANHATTAN STORAGE BED PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction. Carefully open the pack supplied and check the contents against the parts
More informationINSTRUCTIONS: LocknCharge Laptop Carts
INSTRUCTIONS: LocknCharge Laptop Carts www.lockncharge.com Extra Tools required: Hammer, Philips head screwdriver, medium adjustable spanner. (Allen key supplied) (Panel colours for illustration purposes
More informationStandard Royal Inspiration Station
IS2 Standard Royal Inspiration Station R Assembly uide IS2_2013_A Check out our other products online at www.copernicused.com or assistance, please contact us: 1-800-267-8494 Email info@copernicused.com
More informationJOHN DEERE AG & TURF DIVISION OMM165241 K1 OPERATOR S MANUAL
JOHN DEERE AG & TURF DIVISION M165241 K1 Spreader LP39087 OMM165241 K1 OPERATOR S MANUAL Original Instruction All information, illustrations and specifications in this manual are based on the latest information
More informationLIEBERT VNSA Installation Sheet
LIEBERT VNSA Installation Sheet Description The Liebert vnsa network switch is designed for connecting multiple Ethernet-ready devices and comes in various models. The unit may have: A Liebert icom display
More informationOwner's Manual & Assembly Instructions
Owner's Manual & Assembly Instructions BO01 PATIO COVER/CARPORT Model No. PC1010 Attached 705220511 Missing Parts, Questions on Assembly? Call: 1-800-851-1085 or assist@arrowsheds.com Do not return to
More informationLED MOTION ACTIVATED FLOOD LIGHT
Utilitech & UT Design are registered trademarks of LF, LLC. All Rights Reserved. ITEM #0460794, 0459228 LED MOTION ACTIVATED FLOOD LIGHT MODEL #SE1019-WH3-02LF0-U, SE1019-TBZ-02LF0-U Français p. 8 Español
More informationKITCHEN INSTALLATION GUIDE
KITCHEN INSTALLATION GUIDE The step-by-step guide to installing your new kitchen right The materials and tools you ll need This brochure is your guide to preparing and installing your new kitchen. Inside
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure
More informationCDG 10 X 20 Tradeshow Booth Exhibit Setup Instructions
CDG 10 X 20 Tradeshow Booth Exhibit Setup Instructions Hosted Backup Modularity (MBS) CABS Hosted Backup Modularity (MBS) CABS Are your vital company Our highly flexible, web- The highest standard Are
More informationPulleys and Belt. Install the Major Accessory and Pulley. Install the Motor Pulley NOTE. Align the Motor Pulley and the Tool Pulley NOTE
Pulleys and Belt Pulley Guard - 505862 Install the Major Accessory and Pulley 1. Place the short end of the mounting base holes, and insert - but don t tighten - the setscrews. If the Major Accessory has
More informationBase Cabinet Assembly Instructions
Base Cabinet Assembly Instructions Publication Number TSG-BCAI-001 Version 1.0 July 2012 2012 The Shekia Group, LLC (TSG) All Rights Reserved. Notice Every effort was made to ensure that the information
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationWall-Mounting your HP computer. User Guide
Wall-Mounting your HP computer User Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should
More informationMEDIUM FLAT PANEL DISPLAY STATIC MOUNT MSR Series
INSTALLATION INSTRUCTIONS MEDIUM FLAT PANEL DISPLAY STATIC MOUNT The static mount accommodates medium flat panel displays weighing up to 125 lbs (57 kgs). The teardrop holes in the mount allow for quick
More informationDETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT
-J00 REV. 00-- DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT GENERAL Kit Number -A, 0-, -, 0-, -, - 0, -0 Models These kits fit and later FXST, FXSTB, FXSTC, and and later FXDWG Harley-Davidson model
More informationBeautifully Traditional
Arcade 800mm Single Sliding Door Quadrant - nickel Arcade 900mm Single Sliding Door Quadrant - nickel ARC48 ARC49 INSTALLATION INSTRUCTIONS A www.arcadebathrooms.com IMPORTANT - Please read before installation
More informationAssembly GUIDE. display wine cellar kits. Required. Suggested. Questions? 888.373.6057. or visit wineracksamerica.com
Page 1 Middle Ladder End Ladder Display Tray Screwless Connector Package Contents * All models follow the same assembly procedure varying only in the number of middle ladders your rack will require. Depending
More informationInstallation Manual. Solar Pool Heating System. Read the complete manual before beginning the installation
Solar Pool Heating System Installation Manual Read the complete manual before beginning the installation 1. Sizing the System Visit www.techno-solis.com to size the system using the sizing calculator.
More informationRetail Reception kiosk
Retail Reception kiosk put 42" corner post in below 66" to allow post to extend above kiosk for raised box sign Mini cantilever option - 24" overhead support leg Mini cantilever option - 24" overhead 66/48E
More informationOwner s Manual Gantry Cranes
Owner s Manual Gantry Cranes Fixed Height Gantry Crane MODEL NUMBER: SERIAL NUMBER: CAPACITY IN TONS: Telescoping Gantry Crane Bushman AvonTec 262-790-4200, 800338-7810, Fax 262-790-4200 www.bushmanavontec.com
More informationCombination Unit 5'6" Windows a i o P t
for Andersen 5'6" Double-Hung Venting s Windows a i o P t o rs D o Congratulations You have just purchased one of the many fine Andersen products. For ease of assembly and installation and continued enjoyment
More information