Material. Selections

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Material. Selections"

Transcription

1 Chapter Material 28 Selections ASME Design Code - Plate Materials Ferrous Plate Materials Carbon Steel Heat Treated Steel Low Alloy Steel High Alloy Steel Non-Ferrous Plate Materials ASME Design Code - Clad Plate Materials ASME Design Code - Tube Materials Ferrous Tube Materials Carbon Steel Low Alloy Steel High Alloy Steel Non-Ferrous Tube Materials BS Design Code - Plate Materials Ferrous Plate Materials Carbon Steel Heat Treated Steel Low Alloy Steel High Alloy Steel Non-Ferrous Plate Materials BS Design Code - Clad Plate Materials BS Design Code - Tube Materials Ferrous Tube Materials Carbon Steel Low Alloy Steel High Alloy Steel Non-Ferrous Tube Materials JIS Design Code - Plate Materials Ferrous Plate Materials Carbon Steel Heat Treated Steel Low Alloy Steel High alloy Steel Non-Ferrous Plate Materials G3 ICARUS Cpation, 1998.

2 28-2 ICARUS Reference JIS Design Code - Clad Plate Materials JIS Design Code - Tube Materials Ferrous Tube Materials Carbon Steel Low Alloy Steel High Alloy Steel Non-Ferrous Tube Materials DIN Design Code - Plate Materials Ferrous Plate Materials Carbon Steel Heat Treated Steel Low Alloy Steel High Alloy Steel Non-Ferrous Plate Materials DIN Design Code - Clad Plate Materials DIN Design Code - Tube Materials Ferrous Tube Materials Carbon Steel Low Alloy Steel High Alloy Steel Non-Ferrous Tube Materials Lining Materials Brick Acid-Resistant Applied Over Membrane-Line Carbon Steel Firebrick Monolithic Lining Abrasion Resistant Linings; Replaceable Organic, Glass, Metallic Casting Materials Packing Materials ICARUS Cpation, G3

3 Chapter 28: Material Selections 28-3 ASME Design Code - Plate Materials ASME Ferrous Plate Materials - Carbon Steel Internal Pressure External Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-36 (structural steel) A A-283 Low and intermediate strength carbon steel plates of structural quality (C) A 283C na na A-285 Low and intermediate strength carbon steel plates f pressure vessels (C) A A 285C CS A-299 Carbon-manganese-silicon steel plates f plates f pressure vessels: C - Mn - Si A A-455 Pressure vessel plates, carbon steel, high strength manganese (A) A A-515 Carbon steel plates f pressure vessels f intermediate and higher temperature service: (70) C - Si A A-516 Carbon steel plates f pressure vessels moderate and lower temperature service: (70) C - Si A na = material not selectable f vacuum design G3 ICARUS Cpation, 1998.

4 28-4 ICARUS Reference ASME Ferrous Plate Materials - Heat Treated Steel Internal Pressure External Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-353 Nine percent nickel alloy steel plates, double nmalized and tempered f pressure vessels: 9Ni A na na A-553 Eight and nine percent nickel alloy steel plate, quenched and tempered, f pressure vessels: (Type 1) 9Ni A na na A-517 High strength alloy steel plates, quenched and tempered, f pressure vessels: (A) Cr - Mn - Si A517A na na (B) Cr - Mn - Si A517B na na (E) Cr - Mn - Si A517E na na (F) Cr - Mn - Si A517F na na na = material not selectable f vacuum design ICARUS Cpation, G3

5 Chapter 28: Material Selections 28-5 ASME Ferrous Plate Materials - Low Alloy Steel Internal Pressure External Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-202 Chromium-manganese-silicon alloy steel plates f pressure vessels (A) A202A (B) A A202B A-203 Nickel alloy steel plates f pressure vessels: (A) 2.5Ni A203A (B) 2.5Ni A203B (D) 3.5Ni A203D (E) 3.5Ni A203E A-204 Molybdenum alloy steel plates f pressure vessels: (A) C -.5Mo A204A (B) C -.5Mo A204B (C) C -.5Mo A A204C A-302 Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates f pressure vessels: (A) Mn -.5Mo A302A (B) Mn -.5Mo A A302B (C) Mn -.5Mo - Ni A302C (D) Mn -.5Mo - Ni A302D A-387 Pressure vessel plates, alloy steel, chromium-molybdenum: (2 CL 1).5Cr -.5Mo A387A (2 CL 2).5Cr -.5Mo A387G (12 CL 1) 1Cr -.5Mo A387B (12 CL 2) 1Cr -.5Mo A387H (11 CL 1) 1.25Cr -.5Mo - Si A387C (11 CL 2) 1.25Cr -.5Mo - Si A387J (22 CL 1) 2.25Cr - 1Mo A387D (22 CL 2) 2.25Cr - 1Mo A387K (21 CL 1) 3Cr - 1Mo A387E (21 CL 2) 3Cr - 1Mo A387L (5 CL 1) 5Cr -.5Mo A387F (5 CL 2) 5Cr -.5Mo A387M G3 ICARUS Cpation, 1998.

6 28-6 ICARUS Reference ASME Ferrous Plate Materials - Low Alloy Steel (continued) Internal Pressure External Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-533 Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates, quenched and tempered, f pressure vessels: (A CL 1) C - Mn - Mo A533A na na (B CL 1) C - Mn - Mo - Ni A533B na na (C CL 1) C - Mn - Mo - Ni A533C na na na = material not selectable f vacuum design ICARUS Cpation, G3

7 Chapter 28: Material Selections 28-7 ASME Ferrous Plate Materials - High Alloy Steel Internal Pressure External Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-240 Chromium and chromium-nickel stainless steel plate, sheet, and strip f fusion-welded unfired pressure vessels: (304L) 8Cr - 8Ni 304L (304) 18Cr - 8Ni SS (316L) 16Cr - 12Ni - 2Mo 316L (316) 16Cr - 12Ni - 2Mo SS (316Ti) 16Cr - 12Ni - 2Mo-Ti 316TI (317) 18Cr - 10Ni - 3Mo SS (321) 18Cr - 10Ni - Ti SS (347) 18Cr - 10Ni - Cb SS (348) 18Cr - 10Ni - Cb SS (2205) Duplex S Cr - 5Ni - 3Mo (410) 13Cr SS (430) 17Cr SS na = material not selectable f vacuum design G3 ICARUS Cpation, 1998.

8 28-8 ICARUS Reference ASME Non-Ferrous Plate Materials Internal Pressure External Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C B-209 Aluminum-alloy sheet and plate: (1100) Al A na na (3003) Al A na na (5052) Al A na na (5083) Al A na na (5086) Al A na na (6061) Al A na na B-171 Copper and copper alloys - Naval brass (464) CA B-11 Copper plates f locomotive fireboxes: (110) Cu CU CA110 B-96 Copper-silicon alloy plate and sheet f pressure vessels: (655) Cu - Zn CA B-152 Copper sheet, strip, plate, and rolled bar: (122) Cu CA B-171 Copper-nickel alloy plate and sheet f pressure vessels: (715) Cu - Ni 70/30 CA na = material not selectable f vacuum design ICARUS Cpation, G3

9 Chapter 28: Material Selections 28-9 ASME Non-Ferrous Plate Materials (continued) Internal Pressure External Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C B-333 Hastelloy: (B) Ni - Mo HAST HASTB B-575 Hastelloy: (C-276) Ni - Mo - Cr HASTC B-409 Specification f nickel-iron-chromium alloy plate, sheet, and strip: (800) Ni - Fe - Cr I B-424 Nickel-iron-chromium-molybdenumcopper alloy plate, sheet, and strip: (825) Ni - Fe - Cr - Mo - Cu I B-463 Carpenter 20 alloy plate, sheet and strip: (20Cb) Cr - Ni - Fe - Mo - Cu - Cb C B-168 Nickel-chromium-iron alloy plate, sheet, and strip, (600) Inconel: Ni - Cr - Fe INCNL I600 B-162 Nickel plate, sheet, and strip: (200) Ni NI NI (201) Ni-Low C NI B-127 Nickel-copper alloy plate, sheet, and strip: (400) Ni - Cu MONEL M400 B-265 Titanium and titanium alloy strip, sheet, and plate: (1) Ti TI35A na na (2) Ti TI TI50A na = material not selectable f vacuum design G3 ICARUS Cpation, 1998.

10 28-10 ICARUS Reference ASME Design Code - Clad Plate Materials System Material Classification Material Description* Grade Symbol Vessel Base (Backing Material)** ASTM A-285 C A285C A-204 B A204B A-204 C A204C A A 515 A A 516 A CL 1 A387B A CL 2 A387H A CL 1 A387C A CL 2 A387J A CL 1 A387D A CL 2 A387K Cladding Material (Process Side) Stainless steel type 304 SS L 304L 316 SS L 316L 321 SS SS SS SS430 Nickel alloy 200 NI NI201 Monel 400 MONEL Inconel 600 INCNL Ni-Fe-Cr 800 I800 Ni-Fe-Cr-Mo-Cu 825 I825 Carpenter 20 20Cb C 20 Titanium 2 TI Hastelloy B B HASTB Hastelloy C C-276 HASTC * See Plate Materials (ASME Code) f further material descriptions. ** Only these base materials may be used with the above list of cladding materials. No other combination may be selected. ICARUS Cpation, G3

11 Chapter 28: Material Selections ASME Design Code - Tube Materials ASME Ferrous Tube Materials - Carbon Steel Pressure Pressure System ASTM Default Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) A-179 Seamless cold-drawn low-carbon steel heat exchanger and condenser tubes A A285C A-192 Seamless carbon steel boiler tubes f high-pressure service A A 515 A-210 Seamless medium carbon steel boiler and superheater tubes (A-1) A210A A 515 (C) A210C A 515 A-214 Electric-resistance-welded carbon steel heat exchanger and condenser tubes A A 515 A-334 Seamless carbon steel tubes f low temperature service (1) A334A A 442 (6) A334B A 442 G3 ICARUS Cpation, 1998.

12 28-12 ICARUS Reference ASME Ferrous Tube Materials - Low Alloy Steel Pressure Pressure System ASTM Default Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) A-199 Seamless cold-drawn intermediate alloy steel heat exchanger and condenser tubes: (T11) 1.25Cr -.5Mo - Si A199C A387C (T22) 2.5Cr - 1Mo A199D A387D (T21) 3Cr -.9Mo A199E A387E (T5) 5Cr -.5Mo A199F A387F A-209 Seamless carbon-molybdenum alloy steel boiler and superheater tubes: (T1) C -.5Mo A A 204 (T1A) C -.5Mo A209A A 204 (T1B) C -.5Mo A209B A 204 A-213 Seamless ferritic and austenitic alloy steel boiler, superheater, and heat exchanger tubes: (T2).5Cr -.5Mo A213A A387A (T12) 1Cr -.5Mo A213B A387B (T11) 1.25Cr -.5Mo - Si A213C A387C (T22) 2.25Cr - 1Mo A213D A387D (T21) 3Cr -.9Mo A213E A387E (T5) 5Cr -.5Mo A213F A387F ICARUS Cpation, G3

13 Chapter 28: Material Selections ASME Ferrous Tube Materials - High Alloy Steel Pressure Pressure System ASTM Default Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) A-213 Seamless Ferritic and austenitic alloy steel boiler, superheater, and heat exchanger tubes: TP304 18Cr - 8Ni 304S SS304 TP304L 18Cr - 8Ni 304LS L TP316 16Cr - 12Ni - 2Mo 316S SS316 TP316L 16Cr - 12Ni - 2Mo 316LS L TP321 18Cr - 10Ni - Ti 321S SS321 TP347 18Cr - 10Ni - Cb 347S SS347 A-249 Welded austenitic steel boiler superheater, heat exchanger, and condenser tubes: TP304 18Cr - 8Ni 304W SS304 TP304L 18Cr - 8Ni 304LW L TP316 16Cr - 12Ni - 2Mo 316W SS316 TP316L 16Cr - 12Ni - 2Mo 316LW L TP321 18Cr - 10Ni - Ti 321W SS321 TP347 18Cr - 10Ni - Cb 347W SS347 A-268 TP410 Seamless tubes 410S SS410 13Cr TP410 Welded tubes 410W SS410 13Cr A-789 Welded duplex austenitic steel tubes: (S31803) 22Cr - 5Ni - 3Mo 2205W S2205 G3 ICARUS Cpation, 1998.

14 28-14 ICARUS Reference ASME Non-Ferrous Tube Materials Pressure Pressure System ASTM Default Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) B-111 Seamless copper and copper alloy tubes f use in surface condensers, evapats and heat exchangers: (122) Cu CA A285C (687) Cu - Al CA A285C (706) Cu - Ni 90/10 CA A285C (715) Cu - Ni 70/30 CA A285C Admiralty Brass (443) CA A285C (444) CA A285C (445) CA A285C B-163 Seamless cold-drawn nickel tubes f general crosive service: (200) Ni NI NI200 (201) Ni-Low C NI NI201 B-163 Monel (400) Ni - Cu MONEL MONEL B-163 Inconel (600) Ni - Cr - Fe INCNL INCNL I600 B-163 Incoloy (800) Ni - Fe - Cr I I800 (825) Ni - Fe - Cr - Mo - Cu I I825 B-619 Hastelloy (B) Ni - Mo HAST HASTB HASTB (C-276) Ni - Mo - Cr HASTC HASTC B-468 Carpenter 20 (20Cb) Cr - Ni - Fe - Mo - Cu - Cb C C 20 B-338 Titanium (2) Ti TI50A TI50A ICARUS Cpation, G3

15 Chapter 28: Material Selections BS Design Code - Plate Materials BS Ferrous Plate Materials - Carbon Steel BS* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-36 (Structural steel) A A-283 Low and intermediate strength carbon steel plates of structural quality * A 283C na na A-285 Low and intermediate strength carbon steel plates f pressure vessels * A * A 285C CS A-299 Carbon-manganese-silicon steel plates f pressure vessels: * C - Mn - Si A A-455 Pressure vessel plates, carbon steel, high strength manganese * A A-515 Carbon steel plates f pressure vessels f intermediate and higher temperature service: * C - Si A A-516 Carbon steel plates f pressure vessels f moderate and lower temperature service: * C - Si A na = material not selectable f vacuum design G3 ICARUS Cpation, 1998.

16 28-16 ICARUS Reference BS Ferrous Plate Materials - Heat Treated Steel BS* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-353 Nine percent nickel alloy steel plates, double nmalized and tempered f pressure vessels: 510N* 9Ni A na na A-553 Eight and nine percent nickel alloy steel plate, quenched and tempered, f pressure vessels: 510* 9Ni A na na A-517 High strength alloy steel plates, quenched and tempered, f pressure vessels: (A) Cr - Mn - Si A517A na na (B) Cr - Mn - Si A517B na na (E) Cr - Mn - Si A517E na na (F) Cr - Mn - Si A517F na na na = material not selectable f vacuum design ICARUS Cpation, G3

17 Chapter 28: Material Selections BS Ferrous Plate Materials - Low Alloy Steel BS* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-202 Chromium-manganese-silicon alloy steel plates f pressure vessels (A) A202A (B) A A202B A-203 Nickel alloy steel plates f pressure vessels: (A) 2.5Ni A203A (B) 2.5Ni A203B (E) 3.5Ni A203E * 3.5Ni A203D A-204 Molybdenum alloy steel plates f pressure vessels: (C) C -.5Mo A A204C 240* C -.5Mo A204A * C -.5Mo A204B A-302 Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates f pressure vessels: (A) Mn -.5Mo A302A (B) Mn -.5Mo A A302B (C) Mn -.5Mo - Ni A302C (D) Mn -.5Mo - Ni A302D G3 ICARUS Cpation, 1998.

18 28-18 ICARUS Reference BS Ferrous Plate Materials - Low Alloy Steel (continuted) BS* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-387 Pressure vessel plates, alloy steel, chromium-molybdenum: (2 CL 1).5Cr -.5Mo A387A (2 CL 2).5Cr -.5Mo A387G * 1Cr -.5Mo A387B (12 CL 2) 1Cr -.5Mo A387H * 1.25Cr -.5Mo - Si A387C (11 CL 2) 1.25Cr -.5Mo - Si A387J * 2.25Cr - 1Mo A387D (22 CL 2) 2.25Cr - 1Mo A387K (21 CL 1) 3Cr - 1Mo A387E (21 CL 2) 3Cr - 1Mo A387L (5 CL 1) 5Cr -.5Mo A387F (5 CL 2) 5Cr -.5Mo A387M A-533 Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates, quenched and tempered, f pressure vessels: (A CL 1) C - Mn - Mo A533A na na (B CL 1) C - Mn - Mo - Ni A533B na na (C CL 1) C - Mn - Mo - Ni A533C na na na = material not selectable f vacuum design ICARUS Cpation, G3

19 Chapter 28: Material Selections BS Ferrous Plate Materials - High Alloy Steel BS* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-240 Chromium and chromium-nickel stainless steel plate, sheet, and strip f fusion-welded unfired pressure vessels: (317) 18Cr - 10Ni - 3Mo SS (348) 18Cr - 10Ni - Cb SS S13* Duplex S Cr - 5Ni - 3Mo (410) 13Cr SS (430) 17Cr SS S31* 18Cr - 8Ni SS S11* 18Cr - 8Ni 304L S31* 16Cr - 12Ni - 2Mo SS S11* 16Cr - 12Ni - 2Mo 316L * 16Cr - 12Ni - 2Mo - Ti 316TI S31* 18Cr - 10Ni - Ti SS S31* 18Cr - 10Ni - Cb SS G3 ICARUS Cpation, 1998.

20 28-20 ICARUS Reference BS Non-Ferrous Plate Materials BS* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C 1470* Aluminum-alloy sheet and plate: (1100)* Al A na na (3003)* Al A na na (5052)* Al A na na (5083)* Al A na na (5086)* Al A na na (6061)* Al A na na B-171 Copper and copper alloys - Naval brass (464) CA B-11 Copper plates f locomotive fireboxes: (110) Cu CU CA110 B-96 Copper-silicon alloy plate and sheet f pressure vessels: (655) Cu - Zn CA B-152 Copper sheet, strip, plate, and rolled bar: (122) Cu CA B-171 Copper-nickel alloy plate and sheet f pressure vessels: (715) Cu - Ni 70/30 CA na = material not selectable f vacuum design ICARUS Cpation, G3

21 Chapter 28: Material Selections BS Non-Ferrous Plate Materials (continued) BS* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C B-333 Hastelloy: (B) Ni - Mo HAST HASTB B-575 Hastelloy: (C-276) Ni - Mo - Cr HASTC B-409 Specification f nickel-iron-chromium alloy plate, sheet, and strip: (800) Ni - Fe - Cr I B-424 Nickel-iron-chromium-molybdenumcopper alloy plate, sheet, and strip: NA15* Ni - Fe - Cr - Mo - Cu I B-463 Carpenter 20 alloy plate, sheet and strip: (20Cb) Cr - Ni - Fe - Mo - Cu - Cb C B-168 Nickel-chromium-iron alloy plate, sheet, and strip: (600) Ni - Cr - Fe INCNL I600 B-162 Nickel plate, sheet, and strip: (200) Ni NI NI (201) Ni-Low C NI B-127 Nickel-copper alloy plate, sheet, and strip: (400) Ni - Cu MONEL M400 B-265 Titanium and titanium alloy strip, sheet, and plate: (1) Ti TI35A na na (2) Ti TI TI50A na = material not selectable f vacuum design G3 ICARUS Cpation, 1998.

22 28-22 ICARUS Reference BS Design Code - Clad Plate Materials System Material Classification Material Description* Grade Symbol Vessel Base (Backing Material)** ASTM A-285 C A285C 261 A-204 B A204B A-204 C A204C A A A A A CL 1 A387B 620 A CL 2 A387H 621 A CL 1 A387C 621 A CL 2 A387J A CL 1 A387D A CL 2 A387K Cladding Material (Process Side) 304-S SS S11 304L 304L 316-S SS S11 316L 316L 321-S SS S SS SS SS430 Nickel alloy 200 NI NI201 Monel 400 MONEL Inconel 600 INCNL Ni-Fe-Cr 800 I800 Ni-Fe-Cr-Mo-Cu 825 I825 Carpenter 20 20Cb C 20 Titanium 2 TI Hastelloy B B HASTB Hastelloy C C-276 HASTC * See Plate Materials (BS Code) f further material descriptions. ** Only these base materials may be used with the above list of cladding materials. No other combination may be selected. ICARUS Cpation, G3

23 Chapter 28: Material Selections BS Design Code - Tube Materials BS Ferrous Tube Materials - Carbon Steel BS* Pressure Pressure System Default ASTM Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) A-179 Seamless cold-drawn low-carbon steel heat exchanger and condenser tubes 320* A A285C A-192 Seamless carbon steel boiler tubes f high-pressure service 410* A A 515 A-210 Seamless medium carbon steel boiler and superheater tubes (A-1) A210A A 515 (C) A210C A 515 A-214 Electric-resistance-welded carbon steel heat exchanger and condenser tubes 360* A A 515 A-334 Seamless carbon steel tubes f low temperature service 410-LT50* A334A A 442 (6) A334B A 442 G3 ICARUS Cpation, 1998.

24 28-24 ICARUS Reference BS Ferrous Tube Materials - Low Alloy Steel BS* Pressure Pressure System Default ASTM Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) A-199 Seamless cold-drawn intermediate alloy steel heat exchanger and condenser tubes: (T11) 1.25Cr -.5Mo - Si A199C A387C (T22) 2.5Cr - 1Mo A199D A387D (T21) 3Cr -.9Mo A199E A387E (T5) 5Cr -.5Mo A199F A387F A-209 Seamless carbon-molybdenum alloy steel boiler and superheater tubes: (T1) C -.5Mo A A * C -.5Mo A209A A 204 (T1B) C -.5Mo A209B A 204 A-213 Seamless ferritic and austenitic alloy steel boiler, superheater, and heat exchanger tubes: (T2).5Cr -.5Mo A213A A387A (T21) 3Cr -.9Mo A213E A387E * 1Cr -.5Mo A213B A387B * 1.25Cr -.5Mo - Si A213C A387C * 2.25Cr - 1Mo A213D A387D * 5Cr -.5Mo A213F A387F ICARUS Cpation, G3

25 Chapter 28: Material Selections BS Ferrous Tube Materials - High Alloy Steel BS* Pressure Pressure System Default ASTM Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) A-213 Seamless Ferritic and austenitic alloy steel boiler, superheater, and heat exchanger tubes: 304-S18* 18Cr - 8Ni 304S SS S14* 18Cr - 8Ni 304LS L 316-S18* 16Cr - 12Ni - 2Mo 316S SS S14* 16Cr - 12Ni - 2Mo 316LS L 321-S18* 18Cr - 10Ni - Ti 321S SS S18* 18Cr - 10Ni - Cb 347S SS347 A-249 Welded austenitic steel boiler superheater, heat exchanger, and condenser tubes: 304-S25* 18Cr - 8Ni 304W SS S22* 18Cr - 8Ni 304LW L 316-S26* 16Cr - 12Ni - 2Mo 316W SS S22* 16Cr - 12Ni - 2Mo 316LW L 321-S22* 18Cr - 10Ni - Ti 321W SS S17* 18Cr - 10Ni - Cb 347W SS347 A-268 TP410 Seamless tubes 410S SS Cr TP410 Welded tubes 410W SS Cr A-789 Welded duplex austenitic steel tubes: (S31803) 22Cr - 5Ni - 3Mo 2205W S2205 G3 ICARUS Cpation, 1998.

26 28-26 ICARUS Reference BS Non-Ferrous Tube Materials BS* Pressure Pressure System Default ASTM Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) B-111 Seamless copper and copper alloy tubes f use in surface condensers, evapats and heat exchangers: (122) Cu CA A285C (687) Cu - Al CA A285C (706) Cu - Ni 90/10 CA A285C (715) Cu - Ni 70/30 CA A285C Admiralty Brass (443) CA A285C (444) CA A285C (445) CA A285C B-163 Seamless cold-drawn nickel tubes f general crosive service: (200) Ni NI NI200 (201) Ni - Low C NI NI201 B-163 Monel (Seamless) (400) Ni - Cu MONEL MONEL B-163 Inconel (Welded) (600) Ni - Cr - Fe INCNL INCNL I600 B-163 Incoloy (800) Ni - Fe - Cr (Welded) I I800 (825) Ni - Fe - Cr - Mo - Cu (Seamless) I I825 B-619 Hastelloy (Welded) (B) Ni - Mo HAST HASTB HASTB (C-276) Ni - Mo - Cr HASTC HASTC B-468 Carpenter 20 (Welded) (20Cb) Cr - Ni - Fe - Mo - Cu - Cb C C 20 B-338 Titanium (Welded) (2) Ti TI50A TI50A ICARUS Cpation, G3

27 Chapter 28: Material Selections JIS Design Code - Plate Materials JIS Ferrous Plate Materials - Carbon Steel Pressure Pressure JIS* ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C G-3101* (structural steel) A SS400* G-3106* Low and intermediate strength carbon steel plates of structural quality SM520C* A 283C na na G-3115* Low and intermediate strength steel plates f pressure vessels SPV355* A A 285C CS G-3115* SPV450* Carbon-manganese-silicon steel plates f pressure vessels: C - Mn - Si A A-455 Pressure vessel plates, carbon steel, high strength manganese (A) A G-3118* Carbon steel plates f pressure vessels f intermediate and higher temperature service: SGV480* C - Si A G-3126* Carbon steel plates f pressure vessels f moderate and lower temperature service: SLA360* C - Si A na = material not selectable f vacuum design G3 ICARUS Cpation, 1998.

28 28-28 ICARUS Reference JIS Ferrous Plate Materials - Heat Treated Steel Pressure Pressure JIS* ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C G-3127* Nine percent nickel alloy steel plates, double nmalized and tempered f pressure vessels: SL9N520* 9Ni A na na G-3127* Eight and nine percent nickel alloy steel plate, quenched and tempered, f pressure vessels: SL9N590* 9Ni A na na A-517 High strength alloy steel plates, quenched and tempered, f pressure vessels: (A) Cr - Mn - Si A517A na na (B) Cr - Mn - Si A517B na na (E) Cr - Mn - Si A517E na na (F) Cr - Mn - Si A517F na na na = material not selectable f vacuum design ICARUS Cpation, G3

29 Chapter 28: Material Selections JIS Ferrous Plate Materials - Low Alloy Steel Pressure Pressure JIS* ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A-202 Chromium-manganese-silicon alloy steel plates f pressure vessels (A) A202A (B) A A202B G-3127* Nickel alloy steel plates f pressure vessels: SL2N255* 2.5Ni A203A (B) 2.5Ni A203B SL3N255* 3.5Ni A203D SL3N275* 3.5Ni A203E G-3103* Molybdenum alloy steel plates f pressure vessels: SB450M* C -.5Mo A204A SB480M* C -.5Mo A204B (C) C -.5Mo A A204C G-3119* Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates f pressure vessels: SBV1A* Mn -.5Mo A302A SBV1B* Mn -.5Mo A A302B SBV2* Mn -.5Mo - Ni A302C SBV3* Mn -.5Mo - Ni A302D G-4109* Pressure vessel plates, alloy steel, chromium-molybdenum: SCMV1(A)*.5Cr -.5Mo A387A SCMV1(N)*.5Cr -.5Mo A387G SCMV2(A)* 1Cr -.5Mo A387B SCMV2(N)* 1Cr -.5Mo A387H SCMV3(A)* 1.25Cr -.5Mo - Si A387C SCMV3(N)* 1.25Cr -.5Mo - Si A387J SCMV4(A)* 2.25Cr - 1Mo A387D SCMV4(N)* 2.25Cr - 1Mo A387K SCMV5(A)* 3Cr - 1Mo A387E SCMV5(N)* 3Cr - 1Mo A387L SCMV6(A)* 5Cr -.5Mo A387F SCMV6(N)* Cr -.5Mo A387M G3 ICARUS Cpation, 1998.

30 28-30 ICARUS Reference JIS Ferrous Plate Materials - Low Alloy Steel (continued) Pressure Pressure JIS* ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C G-3120* Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates, quenched and tempered, f pressure vessels: SQV1A* C - Mn - Mo A533A na na SQV2A* C - Mn - Mo - Ni A533B na na SQV3A* C - Mn - Mo - Ni A533C na na na = material not selectable f vacuum design ICARUS Cpation, G3

31 Chapter 28: Material Selections JIS Ferrous Plate Materials - High Alloy Steel Pressure Pressure JIS* ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C G-4303* Chromium and chromium-nickel G-4304* stainless steel plate, sheet, and strip f G-4305* fusion-welded unfired pressure vessels: SUS304L* 18Cr - 8Ni 304L SUS304* 18Cr - 8Ni SS SUS316L* 16Cr - 12Ni - 2Mo 316L SUS316* 16Cr - 12Ni - 2Mo SS SUS316* 16Cr - 12Ni - 2Mo-Ti SS316TI SUS317* 18Cr - 10Ni - 3Mo SS SUS321* 18Cr - 10Ni - Ti SS SUS347* 18Cr - 10Ni - Cb SS (348) 18Cr - 10Ni - Cb SS (2205) Duplex S Cr - 5Ni - 3Mo SUS410* 13Cr SS SUS430* 17Cr SS G3 ICARUS Cpation, 1998.

32 28-32 ICARUS Reference JIS Non-Ferrous Plate Materials Pressure Pressure JIS* ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C H-4000* Aluminum-alloy sheet and plate: A1100P* Al A na na A3003P* Al A na na A5052P* Al A na na A5083P* Al A na na A5086P* Al A na na A6061P* Al A na na H-3100* Copper and copper alloys - Naval brass C4640P* CA H3100* Copper plates f locomotive fireboxes: C1100P* Cu CU CA110 B-96 Copper-silicon alloy plate and sheet f pressure vessels: (655) Cu - Zn CA H-3100* Copper sheet, strip, plate, and rolled bar: C1220P* Cu CA H-3100* Copper-nickel alloy plate and sheet f pressure vessels: C7150P* Cu - Ni 70/30 CA na = material not selectable f vacuum design ICARUS Cpation, G3

33 Chapter 28: Material Selections JIS Non-Ferrous Plate Materials (continued) Pressure Pressure JIS* ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C B-333 Hastelloy: (B) Ni - Mo HAST HASTB B-575 Hastelloy: (C-276) Ni - Mo - Cr HASTC G-4902* Specification f nickel-iron- chromium alloy plate, sheet, and strip: NCF800* Ni - Fe - Cr I B-424 Nickel-iron-chromium-molybdenumcopper alloy plate, sheet, and strip: (825) Ni - Fe - Cr - Mo - Cu I B-463 Carpenter 20 alloy plate, sheet and strip: (20Cb) Cr - Ni - Fe - Mo - Cu - Cb C G-4902* Nickel-chromium-iron alloy plate, sheet, and strip, NCF600* Inconel: Ni - Cr - Fe INCNL I600 B-162 Nickel plate, sheet, and strip: (200) Ni NI NI (201) Ni-Low C NI H-4551* Nickel-copper alloy plate, sheet, and strip: NCuP* Ni - Cu MONEL M400 H-4600* Titanium and titanium alloy strip, sheet, and plate: TP28* Ti TI35A na na TP35* Ti TI TI50A na = material not selectable f vacuum design G3 ICARUS Cpation, 1998.

34 28-34 ICARUS Reference JIS Design Code - Clad Plate Materials System Material Classification Material Description* Grade Symbol Vessel Base (Backing Material)** SPV350 ASTM A-285 C A285C SB480M A-204 B A204B A-204 C A204C SGV480 A A 515 SLA360 A A 516 SCMV2(A) A CL 1 A387B SCMV2(A) A CL 2 A387H SCMV3(A) A CL 1 A387C SCMV3(A) A CL 2 A387J SCMV4(A) A CL 1 A387D SCMV4(A) A CL 2 A387K Cladding Material (Process Side) Stainless steel type SUS SS304 SUS304L 304L 304L SUS SS316 SUS316L 316L 316L SUS SS321 SUS SS347 SUS SS410 SUS SS430 Nickel alloy 200 NI NI201 Monel NCUP 400 MONEL Inconel NCF INCNL Ni-Fe-Cr 800 I800 Ni-Fe-Cr-Mo-Cu 825 I825 Carpenter 20 20Cb C 20 Titanium 2 TI Hastelloy B B HASTB Hastelloy C C-276 HASTC * See Plate Materials (JIS Code) f further material descriptions. ** Only these base materials may be used with the above list of cladding materials. No other combination may be selected. ICARUS Cpation, G3

35 Chapter 28: Material Selections JIS Design Code - Tube Materials JIS Ferrous Tube Materials - Carbon Steel JIS* Pressure Pressure System ASTM Default Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) G-3461* Seamless cold-drawn low-carbon steel heat exchanger and condenser tubes STB340* A A285C A-192 Seamless carbon steel boiler tubes f high-pressure service A A 515 G-3461* Seamless medium carbon steel boiler and superheater tubes STB510* A210A A 515 STB410* A210C A 515 G-3461* Electric-resistance-welded carbon steel heat exchanger and condenser tubes STB340* A A 515 G-3464* Seamless carbon steel tubes f low temperature service (1) A334A A 442 STBL380* A334B A 442 G3 ICARUS Cpation, 1998.

36 28-36 ICARUS Reference JIS Ferrous Tube Materials - Low Alloy Steel JIS* Pressure Pressure System ASTM Default Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) G-3462* Seamless cold-drawn intermediate alloy steel heat exchanger and condenser tubes: STBA23* 1.25Cr -.5Mo - Si A199C A387C STBA24* 2.5Cr - 1Mo A199D A387D (T21) 3Cr -.9Mo A199E A387E STBA25* 5Cr -.5Mo A199F A387F G-3462* Seamless carbon-molybdenum alloy steel boiler and superheater tubes: STBA12* C -.5Mo A A 204 STBA13* C -.5Mo A209A A 204 (T1B) C -.5Mo A209B A 204 G-3462* Seamless ferritic and austenitic alloy steel boiler, superheater, and heat exchanger tubes: STBA20*.5Cr -.5Mo A213A A387A STBA22* 1Cr -.5Mo A213B A387B (T11) 1.25Cr -.5Mo - Si A213C A387C (T22) 2.25Cr - 1Mo A213D A387D (T21) 3Cr -.9Mo A213E A387E (T5) 5Cr -.5Mo A213F A387F ICARUS Cpation, G3

37 Chapter 28: Material Selections JIS Ferrous Tube Materials - High Alloy Steel JIS* Pressure Pressure System ASTM Default Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) G-3463* Seamless Ferritic and austenitic alloy steel boiler, superheater, and heat exchanger tubes: SUS304TB* 18Cr - 8Ni 304S SS304 SUS304LTB* 18Cr - 8Ni 304LS L SUS316TB* 16Cr - 12Ni - 2Mo 316S SS316 SUS316LTB* 16Cr - 12Ni - 2Mo 316LS L SUS321TB* 18Cr - 10Ni - Ti 321S SS321 SUS347TB* 18Cr - 10Ni - Cb 347S SS347 G-3463* Welded austenitic steel boiler superheater, heat exchanger, and condenser tubes: SUS304TB* 18Cr - 8Ni 304W SS304 SUS304LTB* 18Cr - 8Ni 304LW L SUS316TB* 16Cr - 12Ni - 2Mo 316W SS316 SUS316LTB* 16Cr - 12Ni - 2Mo 316LW L SUS321TB* 18Cr - 10Ni - Ti 321W SS321 SUS347TB* 18Cr - 10Ni - Cb 347W SS347 A-268 TP 410 Seamless tubes 410S SS410 13Cr TP 410 Welded tubes 410W SS410 13Cr A-789 Welded duplex austenitic steel tubes: (S31803) 22Cr - 5Ni - 3Mo 2205W S2205 G3 ICARUS Cpation, 1998.

38 28-38 ICARUS Reference JIS Non-Ferrous Tube Materials JIS* Pressure Pressure System ASTM Default Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) H-3300* Seamless copper and copper alloy tubes f use in surface condensers, evapats and heat exchangers: C1220T* Cu CA A285C C6871T* Cu - Al CA A285C C7060T* Cu - Ni 90/10 CA A285C C7150T* Cu - Ni 70/30 CA A285C Admiralty Brass C4430T* CA A285C (444) CA A285C (445) CA A285C B-163 Seamless cold-drawn nickel tubes f general crosive service: (200) Ni NI NI200 (201) Ni-Low C NI NI201 H-4552* Monel NCuT* Ni - Cu MONEL MONEL G-4904* Inconel NCF600TB* Ni - Cr - Fe INCNL INCNL I600 G-4904* Incoloy NCF800TB* Ni - Fe - Cr I I800 NCF825TB* Ni - Fe - Cr - Mo - Cu I I825 B-619 Hastelloy (B) Ni - Mo HAST HASTB HASTB (C-276) Ni - Mo - Cr HASTC HASTC B-468 Carpenter 20 (20Cb) Cr - Ni - Fe - Mo - Cu - Cb C C 20 H-4650* Titanium TB35* Ti TI50A TI50A ICARUS Cpation, G3

39 Chapter 28: Material Selections DIN Design Code - Plate Materials DIN Ferrous Plate Materials - Carbon Steel DIN* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C DIN EN * (structural steel) A S235JRG1* DIN EN * Low and intermediate strength carbon steel plates of structural quality S235JRG2* A 283C na na DIN 17155* Low and intermediate strength steel plates f pressure vessels HII* A A 285C CS DIN 17102* Carbon-manganese-silicon steel plates f pressure vessels: St E 355* C - Mn - Si A A-455 Pressure vessel plates, carbon steel, high strength manganese (A) A DIN 17155* Carbon steel plates f pressure vessels f intermediate and higher temperature service: 19Mn5* A DIN 17102* Carbon steel plates f pressure vessels f moderate and lower temperature service: SIE315* C - Si A na = material not selectable f vacuum design G3 ICARUS Cpation, 1998.

40 28-40 ICARUS Reference DIN Ferrous Plate Materials - Heat Treated Steel DIN* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C SEW 680* Nine percent nickel alloy steel plates, double nmalized and tempered f pressure vessels: X8Ni9* A na na SEW 680* Eight and nine percent nickel alloy steel plate, quenched and tempered, f pressure vessels: X8Ni9* A na na A-517 High strength alloy steel plates, quenched and tempered, f pressure vessels: (A) Cr - Mn - Si A517A na na (B) Cr - Mn - Si A517B na na (E) Cr - Mn - Si A517E na na (F) Cr - Mn - Si A517F na na na = material not selectable f vacuum design ICARUS Cpation, G3

41 Chapter 28: Material Selections DIN Ferrous Plate Materials - Low Alloy Steel DIN* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C A 202 Chromium-manganese-silicon alloy steel plates f pressure vessels (A) A202A (B) A A202B SEW 680* Nickel alloy steel plates f pressure vessels: 14Ni6* A203A Ni14* A203B (D) 3.5Ni A203D (E) 3.5Ni A203E DIN 17155* Molybdenum alloy steel plates f pressure vessels: 15Mo3* A204A (B) C -.5Mo A204B (C) C -.5Mo A A204C Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates f pressure vessels: VdTUV Wbl.376 WB35* 17Mn Mo V64* A302A VdTUV Wbl.377 WB36* 15Ni Cu Mo Nb5* A A302B VdTUV Wbl.378* 12Mn Ni Mo55* A302C VdTUV Wbl384 WB34* 13Mn Ni Mo54* A302D Pressure vessel plates, alloy steel, chromium-molybdenum: (A).5Cr -.5Mo A387A (G).5Cr -.5Mo A387G DIN 17155* 13Cr Mo44* A387B DIN 17155* 13Cr Mo44* A387H (C) 1.25Cr -.5Mo - Si A387C (J) 1.25Cr -.5Mo - Si A387J DIN 17155* 10Cr Mo910* A387D VdTUV Wbl.404* 12Cr Mo910* A387K VdTUV Wbl.007* 12Cr Mo195* A387E VdTUV Wbl.007* 12Cr Mo195* A387L (F) 5Cr -.5Mo A387F (M) Cr -.5Mo A387M G3 ICARUS Cpation, 1998.

42 28-42 ICARUS Reference DIN Ferrous Plate Materials - Low Alloy Steel (continued) DIN* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C SEW 640* Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates, quenched and tempered, f pressure vessels: (A) C - Mn - Mo A533A na na 20 Mn Mo Ni55* A533B na na 12 Mn Ni Mo55* A533C na na na = material not selectable f vacuum design ICARUS Cpation, G3

43 Chapter 28: Material Selections DIN Ferrous Plate Materials - High Alloy Steel DIN* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C DIN 17440* Chromium and chromium-nickel stainless steel plate, sheet, and strip f fusion-welded unfired pressure vessels: X2 Cr Ni1911* 304L X5 Cr Ni1810* SS X2 Cr Ni Mo17132* 316L X5 Cr Ni Mo17122* SS X6 Cr Ni Mo Ti 17122* 316TI X2 Cr Ni Mo18164* SS X6 Cr Ni Ti1810* SS X6 Cr Ni Nb1810* SS (348) SS (2205) Duplex S Cr - 5Ni - 3Mo DIN 17440* X10 Cr13* SS X6 Cr17* SS G3 ICARUS Cpation, 1998.

44 28-44 ICARUS Reference DIN Non-Ferrous Plate Materials DIN* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C DIN 1745* Aluminum-alloy sheet and plate: A1100P* Al A na na Al Mn Cu* A na na Al Mg 2.5* A na na Al Mg 4.5* Mn* A na na Al Mg 4 Mn* A na na Al Mg 7.5 Si Cu* A na na DIN 17660* Copper and copper alloys - Naval brass Cu Zn38 Sn1* CA DIN 1787* Copper plates f locomotive fireboxes: E Cu58* CU E Cu59* CA110 B-96 Copper-silicon alloy plate and sheet f pressure vessels: (655) Cu - Zn CA DIN 1787* Copper sheet, strip, plate, and rolled bar: SF-Cu CA DIN 17664* Copper-nickel alloy plate and sheet f pressure vessels: Cu Ni 30 Mn1 Fe* CA na = material not selectable f vacuum design ICARUS Cpation, G3

45 Chapter 28: Material Selections DIN Non-Ferrous Plate Materials (continued) DIN* Pressure Pressure ASTM Spec System Maximum Temp. and Description and Material Degrees Degrees (Grade) Nominal Composition Symbol F C F C B-333 Hastelloy: (B) Ni - Mo HAST HASTB B-575 Hastelloy: (C-276) Ni - Mo - Cr HASTC VdTUV Wbl.412*Specification f nickel-iron- chromium alloy plate, sheet, and strip: NCF800* X10 Ni Cr Al Ti 3220* I B-424 Nickel-iron-chromium-molybdenumcopper alloy plate, sheet, and strip: (825) Ni - Fe - Cr - Mo - Cu I B-463 Carpenter 20 alloy plate, sheet and strip: (20Cb) Cr - Ni - Fe - Mo - Cu - Cb C VdTUV Wbl.305*Nickel-chromium-iron alloy plate, sheet, and strip, Inconel: Ni Cr15 Fe INCNL I600 B-162 Nickel plate, sheet, and strip: (200) Ni NI NI (201) Ni-Low C NI DIN 17750* Nickel-copper alloy plate, sheet, and strip: Ni Cu 30 Fe F45* MONEL M400 DIN 17860* Titanium and titanium alloy strip, sheet, and plate: * Ti TI35A na na * Ti TI TI50A na = material not selectable f vacuum design G3 ICARUS Cpation, 1998.

46 28-46 ICARUS Reference DIN Design Code - Clad Plate Materials System Material Classification Material Description* Grade Symbol Vessel Base (Backing Material)** DIN St E 355 C A285C A-204 (B) ASTM A-204 B A204B ASTM A-204 C A204C DIN Mn5 70 A 515 DIN SIE A 516 DIN Cr Mo44 12 CL 1 A387B DIN Cr Mo44 12 CL 2 A387H A-387 (C) ASTM A CL 1 A387C A-387 ASTM A CL 2 A387J DIN Cr Mo CL 1 A387D DIN Cr Mo CL 2 A387K Cladding Material (Process Side) Stainless steel type DIN X5 Cr Ni189* 304 SS304 X2 Cr Ni189* 304L 304L X5 Cr Ni Mo1810* 316 SS316 X2 Cr Ni Mo1810* 316L 316L X10 Cr Ni Ti189* 321 SS321 X10 Cr Ni Nb1810* 347 SS347 X10 Cr13* 410 SS410 X8 Cr17* 430 SS430 Nickel alloy 200 NI NI201 Monel NCUP 400 MONEL VdTUV Wbl.305* Ni Cr15 Fe 600 INCNL Ni-Fe-Cr 800 I800 Ni-Fe-Cr-Mo-Cu 825 I825 Carpenter 20 20Cb C 20 Titanium 2 TI Hastelloy B B HASTB Hastelloy C C-276 HASTC * See Plate Materials (German Code) f further material descriptions. ** Only these base materials may be used with the above list of cladding materials. No other combination may be selected. ICARUS Cpation, G3

47 Chapter 28: Material Selections DIN Design Code - Tube Materials DIN Ferrous Tube Materials - Carbon Steel DIN* Pressure Pressure System ASTM Default Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) DIN 2391* Seamless cold-drawn low-carbon steel heat exchanger and condenser tubes St 35GBK* A A285C NBK* DIN 1629* Seamless carbon steel boiler tubes f high-pressure service St 37.0* A A 515 DIN 1629* Seamless medium carbon steel boiler and superheater tubes St 44.0* A210A A 515 St 52.0* A210C A 515 DIN 2393* Electric-resistance-welded carbon steel heat exchanger and condenser tubes St 37-2 NBK* A A 515 SEW 680* Seamless carbon steel tubes f low temperature service TTSt 35N* A334A A 442 (B) A334B A 442 G3 ICARUS Cpation, 1998.

48 28-48 ICARUS Reference DIN Ferrous Tube Materials - Low Alloy Steel DIN* Pressure Pressure System ASTM Default Spec System Maximum Temp. Tubesheet and Description and Material Degrees Degrees Material (Grade) Nominal Composition Symbol F C F C (Plate) Seamless cold-drawn intermediate alloy steel heat exchanger and condenser tubes: DIN 17175* 13Cr Mo44* A199C A387C DIN 17175* 10Cr Mo910* A199D A387D (T21) 3Cr -.9Mo A199E A387E VdTUV007* 12Cr Mo195G A199F A387F Seamless carbon-molybdenum alloy steel boiler and superheater tubes: DIN 17175* 15 Mo3* A A 204 (T1A) C -.5Mo A209A A 204 (T1B) C -.5Mo A209B A 204 Seamless ferritic and austenitic alloy steel boiler, superheater, and heat exchanger tubes: (T2).5Cr -.5Mo A213A A387A DIN17175* 13Cr Mo44* A213B A387B DIN17175* 13Cr Mo44* A213C A387C DIN17175* 10Cr Mo910* A213D A387D (T21) 3Cr -.9Mo A213E A387E VdTUV007* 12Cr Mo195G* A213F A387F ICARUS Cpation, G3

ASTM Standards for Process Piping

ASTM Standards for Process Piping ASTM Standards for Process Piping A1010/A1010M Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip A1011/A1011M Standard Specification for Steel, Sheet and Strip,

More information

Pipe and Tubing Products. Industry Specifications and Scope

Pipe and Tubing Products. Industry Specifications and Scope Pipe and Tubing Products Industry Specifications and Scope Transmission Pipe Specifications API 5L Line Pipe Standard Pipe Transmission of Fluids and Gases (Carbon Steel) API 5L This standard specifies

More information

American Society of Mechanical Engineers

American Society of Mechanical Engineers American Society of Mechanical Engineers ASTM A53 /ASME SA53 Pipe Steel Black and Hot Dipped Zinc Coated Welded and Seamless ASTM A105/ASME SA105 Forgings, Carbon Steel, for Piping Components ASTM A106/ASME

More information

Standards and Related Materials Contained in this Volume:

Standards and Related Materials Contained in this Volume: Volume 01.01, January 2007 Steel - Piping, Tubing, Fittings Standards and Related Materials Contained in this Volume: (Click here for a list of withdrawn standards) A53/A53M-06a Standard Specification

More information

AMERICAN SOCIETY OF TESTING MATERIALS (ASTM)

AMERICAN SOCIETY OF TESTING MATERIALS (ASTM) AMERICAN SOCIETY OF TESTING MATERIALS (ASTM) The Volume#1 details the standars for: 1. standards for various types of steel pipes specifying requirements for high-temperature services, ordinary use, and

More information

ASTM A-48 A-691 ASTM A-500 Tubing ASTM B-75 B626 Only general information is presented here. Please contact ASTM for greater detail.

ASTM A-48 A-691 ASTM A-500 Tubing ASTM B-75 B626 Only general information is presented here. Please contact ASTM for greater detail. ASTM A-48 A-691 ASTM A-500 Tubing ASTM B-75 B626 Only general information is presented here. Please contact ASTM for greater detail. ASTM Number Explanation A-48 This specification covers gray iron castings

More information

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications 1

Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications 1 Designation: A 2/A 2M 04a e1 Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications 1 This standard is issued

More information

ALLOY 800 / 800H / 800AT DATA SHEET

ALLOY 800 / 800H / 800AT DATA SHEET ALLOY 800 / 800H / 800AT DATA SHEET UNS N08800 / UNS N08801 / UNS N08811 GENERAL PROPERTIES ////////////////////////////////////////////////////// //// 800 (UNS N08800), 800H (UNS N08810) and 800AT (UNS

More information

ALLOY 2205 DATA SHEET

ALLOY 2205 DATA SHEET ALLOY 2205 DATA SHEET UNS S32205, EN 1.4462 / UNS S31803 GENERAL PROPERTIES ////////////////////////////////////////////////////// //// 2205 (UNS designations S32205 / S31803) is a 22 % chromium, 3 % molybdenum,

More information

Stainless Steel Instrumentation Fractional / Metric Tubing

Stainless Steel Instrumentation Fractional / Metric Tubing Tubing benefits Tubing has many benefits against piping. Pipe threading or welding is difficult to disassemble and re-assemble. Piping requires skilled worker for welding & threading. Piping is bulky.

More information

SPECIFICATIONS FOR STEEL PIPE

SPECIFICATIONS FOR STEEL PIPE SPECIFICATIONS FOR STEEL PIPE Published pipe standards serve three functions. 1. They dictate manufacturing and testing requirements and prescribed methods of measuring the required mechanical and physical

More information

AWS A5.9 ER 308LSi EN G 19 9 L Si ISO 14343 B SS308LSi. Alloy wt% C Mn Si Cr Ni Mo P S Cu

AWS A5.9 ER 308LSi EN G 19 9 L Si ISO 14343 B SS308LSi. Alloy wt% C Mn Si Cr Ni Mo P S Cu WW-308LSi AWS A5.9 ER 308LSi EN G 19 9 L Si ISO 14343 B SS308LSi WW- 308LSi mainly consists of low C- 18Cr- 8Ni. It is widely used for austenitic stainless steel welding consumable. It has excellent weldability,

More information

Product Range. Seamless Stainless Steel & Nickel-Based Alloy Tubing and Piping

Product Range. Seamless Stainless Steel & Nickel-Based Alloy Tubing and Piping Product Range Seamless Stainless Steel & Nickel-Based Alloy Tubing and Piping Salzgitter Mannesmann Stainless Tubes Typical Application Areas Seamless stainless steel and nickel-based alloy tubes and pipes

More information

1.3.3 When pipe is required for close coiling, this should b specified on the order.

1.3.3 When pipe is required for close coiling, this should b specified on the order. SA 36* SA 53* Covers carbon steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded contrsuction of bidges and buildings, and for general structural purposes. When the

More information

NORSOK STANDARD COMMON REQUIREMENTS WELDING AND INSPECTION OF PIPING

NORSOK STANDARD COMMON REQUIREMENTS WELDING AND INSPECTION OF PIPING NORSOK STANDARD COMMON REQUIREMENTS WELDING AND INSPECTION OF PIPING CONTENTS 1 FOREWORD 2 2 SCOPE 2 3 NORMATIVE REFERENCES 2 4 DEFINITIONS AND ABREVIATIONS 3 4.1 Abreviations 3 4.2 Definitions 4 5 WELDING

More information

Spectifications. ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers)

Spectifications. ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) Spectifications ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) ANSI / ASME B1.20.1 ASME B16.10 ASME B16.11 ASME B16.25 ANSI / ASME B16.28 ANSI / ASME B16.34

More information

Standard Cr-Ni Stainless Steels

Standard Cr-Ni Stainless Steels Standard Cr-Ni Stainless Steels Steel grades Outokumpu EN ASTM 4318 1.4318 301LN 4301 1.4301 304 4307 1.4307 304L 4311 1.4311 304LN 4541 1.4541 321 4306 1.4306 304L Characteristic properties All-purpose

More information

Born from fire, made to endure STAINLESS STEEL

Born from fire, made to endure STAINLESS STEEL Born from fire, made to endure STAINLESS STEEL Acroni is the largest Slovenian steel manufacturer, which produces steel by recycling scrap in an electric arc furnace, casting it on a continuous caster

More information

Hot Rolled Square Steel Bars

Hot Rolled Square Steel Bars Page 1 of 16 Viale Certosa, 249-20151 Milano Tel: +39 02 30 700 - Fax: +39 02 38000 346 - Mail: commerciale.riva@rivagroup.com Production Units: Cerveno (BS), Italy Page 2 of 16 Products STRUCTURAL AND

More information

Contents Nickel Alloys... 2 Copper Alloys... 19 Titanium Alloys... 26 Stainless Steel... 33 Miscellaneous... 35 Welding Material... 37 Contact...

Contents Nickel Alloys... 2 Copper Alloys... 19 Titanium Alloys... 26 Stainless Steel... 33 Miscellaneous... 35 Welding Material... 37 Contact... 2015-04-09 Page 1 Contents Nickel Alloys... 2 Copper Alloys... 19 Titanium Alloys... 26 Stainless Steel... 33 Miscellaneous... 35 Welding Material... 37 Contact... 41 2015-04-09 Page 2 Nickel Alloys Alloy

More information

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes 1

Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes 1 Designation: A 213/A 213M 03b Used in USDOE-NE standards Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes 1 This standard is issued

More information

SPECIFICATIONS FOR STEEL PIPE

SPECIFICATIONS FOR STEEL PIPE SPECIFICATIONS FOR STEEL PIPE Published pipe standards serve three functions. 1. They dictate manufacturing and testing requirements and prescribed methods of measuring the required mechanical and physical

More information

GENERAL PROPERTIES //////////////////////////////////////////////////////

GENERAL PROPERTIES ////////////////////////////////////////////////////// ALLOY 625 DATA SHEET //// Alloy 625 (UNS designation N06625) is a nickel-chromium-molybdenum alloy possessing excellent resistance to oxidation and corrosion over a broad range of corrosive conditions,

More information

Hot Rolled Billets. Production Units: Cerveno (BS), Italy Lesegno (CN), Italy

Hot Rolled Billets. Production Units: Cerveno (BS), Italy Lesegno (CN), Italy Page 1 of 20 Viale Certosa, 249-20151 Milano Tel: +39 02 30 700 - Fax: +39 02 38000 346 - Mail: commerciale.riva@rivagroup.com Production Units: Cerveno (BS), Italy Lesegno (CN), Italy Page 2 of 20 Products

More information

Heat Treating Data Book

Heat Treating Data Book Heat Treating Data Book Tenth Edition E-Book Published by SECO/Warwick Corporation 180 Mercer St., PO Box 908, Meadville, PA 16335 USA www.secowarwick.com SECO/WARWICK Corp. is a member of the SECO/WARWICK

More information

European Welding Standards

European Welding Standards European Welding Standards John Dyson 15 th March 2004 European Standards Harmonised Standards Not all EN Standards are Harmonised, only those that are considered to satisfy relevant ESRs in product directives.

More information

Standard Cr-Ni-Mo Stainless Steels

Standard Cr-Ni-Mo Stainless Steels Standard Cr-Ni-Mo Stainless Steels Steel grades Outokumpu EN ASTM 441 1.441 316 444 1.444 316L 4436 1.4436 316 4432 1.4432 316L 446 1.446 316LN 4429 1.4429 S31653 4571 1.4571 316Ti 4435 1.4435 316L Characteristic

More information

Hot Rolled Round Steel Bars

Hot Rolled Round Steel Bars Page 1 of 20 Viale Certosa, 249-20151 Milano Tel: +39 02 30 700 - Fax: +39 02 38000 346 - Mail: commerciale.riva@rivagroup.com Production Units: Cerveno (BS), Italy Lesegno (CN), Italy Sellero (BS), Italy

More information

TARIFF CODE and updates standard

TARIFF CODE and updates standard TARIFF CODE and updates standard No HS CODE AHTN CODE PRODUCT DESCRIPTION PRODUCT TYPE STANDARDS IDENTIFIED 7207 Semi finished products of iron or non alloy steel Containing by weight less than 0.25% of

More information

NORSOK STANDARD MATERIAL DATA SHEETS FOR PIPING

NORSOK STANDARD MATERIAL DATA SHEETS FOR PIPING NORSOK STANDARD MATERIAL DATA SHEETS FOR PIPING M630 Rev. 2, November 1997 Please note that whilst every effort has been made to ensure the accuracy of the NORSOK standards neither OLF nor TBL or any of

More information

North American Stainless

North American Stainless Introduction: North American Stainless Flat Products Stainless Steel Grade Sheet 309S (S30908)/ EN1.4833 SS309 is a highly alloyed austenitic stainless steel used for its excellent oxidation resistance,

More information

ASTM A860/A860M-09 Standard Specification for Wrought High Strength. Ferritic Steel Butt Welding Fittings. 1. Scope :- 2. Reference Documents :-

ASTM A860/A860M-09 Standard Specification for Wrought High Strength. Ferritic Steel Butt Welding Fittings. 1. Scope :- 2. Reference Documents :- Standard Specification for Wrought High Strength Ferritic Steel Butt Welding Fittings 1. Scope :- 1.1 This specification covers wrought high strength ferritic steel butt-welding fitting of seamless and

More information

Stainless steel grade chart

Stainless steel grade chart Stainless steel grade chart ATLAS STEELS METAL DISTRIBUTION Chemical analysis (%) specified C Si Mn P S Cr Mo Ni Other Austenitic stainless steels 253MA S30815 0.05 1.1-2.0 0.8 0.040 0.030 20.0-22.0 10.0-12.0

More information

Standard Specification for Stainless Steel Bars and Shapes 1

Standard Specification for Stainless Steel Bars and Shapes 1 Designation: A 276 06 Standard Specification for Stainless Steel Bars and Shapes 1 This standard is issued under the fixed designation A 276; the number immediately following the designation indicates

More information

ATI 2205 ATI 2205. Technical Data Sheet. Duplex Stainless Steel GENERAL PROPERTIES. (UNS S31803 and S32205)

ATI 2205 ATI 2205. Technical Data Sheet. Duplex Stainless Steel GENERAL PROPERTIES. (UNS S31803 and S32205) ATI 2205 Duplex Stainless Steel (UNS S31803 and S32205) GENERAL PROPERTIES ATI 2205 alloy (UNS S31803 and/or S32205) is a nitrogen-enhanced duplex stainless steel alloy. The nitrogen serves to significantly

More information

Selectionoftechnical datasheets

Selectionoftechnical datasheets Selectioftechnical datasheets 13 Summary of the alloys technical characteristics LEGEND: ++ = EXCELLENT, + = GOOD, - = AVERAGE, -- = BAD WELDING PAGES PRECIMET AISI or UNS DIN AFNOR Machining Quench hard.

More information

ASTM and SAE-AMS Standards and Specifications for STAINLESS STEEL Stock #: STEEL03

ASTM and SAE-AMS Standards and Specifications for STAINLESS STEEL Stock #: STEEL03 ASTM and SAE-AMS Standards and Specifications for STAINLESS STEEL Stock #: STEEL03 A167-99 Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip A176-99

More information

Diaphragm seal with flange connection With flush diaphragm Model

Diaphragm seal with flange connection With flush diaphragm Model Diaphragm seals Diaphragm seal with flange connection With flush diaphragm Model 990.27 WIKA data sheet DS 99.27 for further approvals see page 3 Applications Chemical process industry Petrochemical industry

More information

North American Stainless

North American Stainless North American Stainless Flat Products Stainless Steel Grade Sheet 310S (S31008)/ EN 1.4845 Introduction: SS310 is a highly alloyed austenitic stainless steel designed for elevated-temperature service.

More information

High-Strength Low-Alloy Steels

High-Strength Low-Alloy Steels High-Strength Low-Alloy Steels Introduction and Overview High-strength low-alloy (HSLA) steels, or microalloyed steels, are designed to provide better mechanical properties and/or greater resistance to

More information

MATERIAL SPECIFICATIONS CATALOGUE

MATERIAL SPECIFICATIONS CATALOGUE MATERIAL SPECIFICATIONS CATALOGUE Manganese Steel High Chrome White Iron Alloy Steel Carbon Steel Stainless Steel SG Iron Cast Iron E X C E L L E N C E T H R O U G H E X P E R I E N C E Foundries has the

More information

Properties and Welding Procedure for Grade 91 Alloy Steel

Properties and Welding Procedure for Grade 91 Alloy Steel International Journal of Engineering Research and Technology. ISSN 0974-3154 Volume 6, Number 6 (2013), pp. 767-772 International Research Publication House http://www.irphouse.com Properties and Welding

More information

North American Stainless

North American Stainless North American Stainless Flat Products Stainless Steel Grade Sheet 201 (S20100) 201LN (S20153) EN 1.4372 Introduction: SS201 is a lower-cost alternative to the conventional Cr-Ni austenitic stainless steels,

More information

ATI 316Ti. ATI 316Ti. Technical Data Sheet. Stainless Steel: Austenitic GENERAL PROPERTIES

ATI 316Ti. ATI 316Ti. Technical Data Sheet. Stainless Steel: Austenitic GENERAL PROPERTIES ATI 316Ti Stainless Steel: Austenitic (UNS S31635) GENERAL PROPERTIES ATI 316Ti stainless is a titanium-stabilized version of Type 316 molybdenum-bearing austenitic stainless steel. It is also known as

More information

Arcos Premium Bare & Covered Electrodes

Arcos Premium Bare & Covered Electrodes Arcos Premium Bare & Covered Electrodes For Welding Stainless Steel Alloys The Standard of Excellence in Covered and Bare Wire Arcos is the company with the reputation and experience you can rely on for

More information

ASTM FITTING SPECIFICATIONS

ASTM FITTING SPECIFICATIONS ASTM FITTING SPECIFICATIONS This general requirements covers summary information and common requirements data extracted from relevant ASTM standards. These standards are used to fittings in conjunction

More information

Rely on Our Material Competence for Your Demanding Industrial Processes

Rely on Our Material Competence for Your Demanding Industrial Processes Cast Materials Rely on Our Material Competence for Your Demanding Industrial Processes Our customer-focused R&D and continuous research on new material options enable us to develop equipment with a strong

More information

North American Stainless

North American Stainless North American Stainless Flat Products Stainless Steel Grade Sheet 430 (S43000)/ EN 1.4016 Introduction: SS430 is a low-carbon plain chromium, ferritic stainless steel without any stabilization of carbon

More information

Material Expansion Coefficients

Material Expansion Coefficients 17 Material Expansion Coefficients Linear Thermal Expansion Coefficients of Metals and Alloys Table 17-1 provides the linear thermal expansion coefficients of the most frequently used metals and allows.

More information

JIS G 4805 SEAMLESS PIPE HIGH CARBON CHROMIUM BEARING STEEL PIPE

JIS G 4805 SEAMLESS PIPE HIGH CARBON CHROMIUM BEARING STEEL PIPE JIS G 4805 SEAMLESS PIPE HIGH CARBON CHROMIUM BEARING STEEL PIPE 1. SCOPE This Japanese Industrial Standard specifies the high carbon chromium bearing steels (hereafter referred to as the "steels") to

More information

Flanged Type Thermowell

Flanged Type Thermowell Flanged Type Thermowell General Description Flanged type thermowells are precision components manufactured to the highest standard from bar or forgings to serve as protective devices for primary sensing

More information

UR 317L: A 3%Mo minimum austenitic stainless steel (317L grade) Thermal conductivity (W m - 1 K - 1 ) Resistivity

UR 317L: A 3%Mo minimum austenitic stainless steel (317L grade) Thermal conductivity (W m - 1 K - 1 ) Resistivity Indu UR 317L UR 317L: A 3%Mo minimum austenitic stainless (317L grade) UR 317L (317L) is an austenitic stainless with a 3% molybdenum addition. Alloy UR 317L (317L) exhibits an austenitic microstructure,

More information

P r o d u c t c a t a l o g

P r o d u c t c a t a l o g Signature of the quality... CONTENTS Abbreviations & Symbols 6 PRODUCT RANGE & CERTIFICATE 9 INDEX 13 Flat Product Qualities & Using Areas 15 Rebar Qualities 20 Billet Qualities 21 Chemical & 23 Hot Rolled

More information

North American Stainless

North American Stainless North American Stainless Long Products Stainless Steel Grade Sheet AISI 316 UNS S31600 EN 1.4401 AISI 316L UNS S31630 EN 1.4404 INTRODUCTION NAS provides 316 and 316L SS, which are molybdenum-bearing austenitic

More information

Tubing Data. Contents. Tubing Selection. Tubing Handling. Tubing Material. Tubing Outside Diameter Hardness. Tubing Wall Thickness

Tubing Data. Contents. Tubing Selection. Tubing Handling. Tubing Material. Tubing Outside Diameter Hardness. Tubing Wall Thickness www.swagelok.com Tubing Data Contents Tubing Selection... 1 Tubing Handling.... 1 Gas Service... 2 Tubing Installation.... 2 Suggested Allowable Working Pressure Tables Carbon Steel Tubing... 3 Stainless

More information

MIG/TIG ARC WELDING FOR STAINLESS STEELS & CARBON STEELS

MIG/TIG ARC WELDING FOR STAINLESS STEELS & CARBON STEELS MIG/TIG RC WELDING FOR STINLESS STEELS & CRBON STEELS SM-308 MIG/TIG RC WELDING FOR STINLESS STEELS & CRBON STEELS WS 5.9 / SME SF5.9 ER308 JIS Z3321 Y308 MIG welding of 18%Cr-8%Ni steel for chemical industries

More information

Appendice Caratteristiche Dettagliate dei Materiali Utilizzati

Appendice Caratteristiche Dettagliate dei Materiali Utilizzati Appendice Caratteristiche Dettagliate dei Materiali Utilizzati A.1 Materiale AISI 9840 UNI 38NiCrMo4 AISI 9840 Steel, 650 C (1200 F) temper, 25 mm (1 in.) round Material Notes: Quenched, 540 C temper,

More information

W-22 STAINLESS STEEL PIPES

W-22 STAINLESS STEEL PIPES Guideline No.: W-22(201510) W-22 STAINLESS STEEL PIPES Issued date: October 20,2015 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection

More information

Seamless Tubes and Pipes for Power Plants

Seamless Tubes and Pipes for Power Plants Seamless Tubes and Pipes for Power Plants Seamless tubes and pipes for Power Plants Features The boiler tubes and pipes are manufactured with materials able to withstand high temperatures and high pressures.

More information

MARTENSITIC STAINLESS STEEL RWL-34

MARTENSITIC STAINLESS STEEL RWL-34 MARTENSITIC STAINLESS STEEL RWL-34 RWL 34 is a Rapid Solidified Powder (RSP) Martensitic Stainless Steel, which is variation of the 420 martensitic stainless steel family with minimum 13 percent chromium

More information

Martin RICHEZ. Franck ZANONCELLI

Martin RICHEZ. Franck ZANONCELLI DILLINGER PRESSURE VESSEL COLLOQUIUM Dillingen 16/17 th september 2009 TOTAL Requirements for equipment in severe wet H2S service. Examples of equipment made from Dillinger steel plates Martin RICHEZ Franck

More information

North American Stainless

North American Stainless North American Stainless Long Products Stainless Steel Grade Sheet 2205 UNS S2205 EN 1.4462 2304 UNS S2304 EN 1.4362 INTRODUCTION Types 2205 and 2304 are duplex stainless steel grades with a microstructure,

More information

Urea and Nitric Acid Plants: Improvement of Shut-Down, Revamping, Debottlenecking and Refurbishment

Urea and Nitric Acid Plants: Improvement of Shut-Down, Revamping, Debottlenecking and Refurbishment pp Urea and Nitric Acid Plants: Improvement of Shut-Down, Revamping, Debottlenecking and Refurbishment J. M. SLUYTERS GEMACO SA Herstal, Belgium A presentation on special corrosion-resistant steels for

More information

A.A.NAJJAR TRADING EST.

A.A.NAJJAR TRADING EST. A.A.NAJJAR TRADING EST. Source of ferrous and non ferrous metals Page 1 ABOUT US We, serve to the requirements of various Industries such as Refineries, Oil & Gas Plants, Fertilizers, Power, Pharmaceuticals,

More information

DET NORSKE VERITAS. Report. Statoil ASA

DET NORSKE VERITAS. Report. Statoil ASA Report EC Master Material Components: Particular material appraisal in accordance with the Pressure Equipment Directive No. 97/23/EC Statoil ASA Report No./DNV Reg No.: 2010-3469/ 12JUZTB-1 Rev 2, 2011-07-05

More information

Specifications for Programs: 737, 747, 757, 767, 777, 787

Specifications for Programs: 737, 747, 757, 767, 777, 787 = Performed by GKN BAC 5000 AN General Sealing 6-262, 6-265, 6-267, 6-270 PSD for 787 Only: 6-242, 6-269, 6-271 PSD for 777 Only: 6-261,6-264, 6-266, 6-269, 6-271 BAC 5004 L Installation of Permanent Fasteners

More information

Caps STANDARD WEIGHT Inches / Pounds

Caps STANDARD WEIGHT Inches / Pounds Standard Caps you are here: Home > Weldbend Catalog > Fittings > Caps Caps STANDARD WEIGHT Inches / Pounds For Metric Units >Click Here Nominal Pipe Size Outside Inside Wall Thickness (T) Length (E) Pipe

More information

Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service 1

Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service 1 Designation: A 182/A 182M 99 An American National Standard Endorsed by Manufacturers Standardization Society of the Valve and Fittings Industry Used in USDOE-NE Standards Standard Specification for Forged

More information

Normy ASTM (American Society for Testing and Materials) dostępne w BG AGH - kolekcja ASTM Standards Book 2006 (stan na dzień 29.02.

Normy ASTM (American Society for Testing and Materials) dostępne w BG AGH - kolekcja ASTM Standards Book 2006 (stan na dzień 29.02. Normy ASTM (American Society for Testing and Materials) dostępne w BG AGH - kolekcja ASTM Standards Book 2006 (stan na dzień 29.02.2012) ASTM Standards (American Society for Testing and Materials) available

More information

Threading Tables. Chart No 1 - Whitworth Threads. Whitworth Form Threads (55 Deg Thread Angle) Dimensions in Inches except where stated.

Threading Tables. Chart No 1 - Whitworth Threads. Whitworth Form Threads (55 Deg Thread Angle) Dimensions in Inches except where stated. Threading Tables C:\British Cars\Tech Papers\Thread Sizes\Threading Tables.doc Source: http://www.oldengine.org/members/diesel/front.htm Chart No 1 - Whitworth Threads Whitworth Form Threads (55 Deg Thread

More information

Gas Distribution and Transportation

Gas Distribution and Transportation Piping System Includes: Pipe Fittings (e.g. elbows, reducers, branch connections, etc.) Flanges, gaskets, bolting Valves Associations involved in generating Codes for piping Design Engineering: ASME ANSI

More information

HEAT TREATMENT OF STEEL

HEAT TREATMENT OF STEEL HEAT TREATMENT OF STEEL Heat Treatment of Steel Most heat treating operations begin with heating the alloy into the austenitic phase field to dissolve the carbide in the iron. Steel heat treating practice

More information

DX2202 Duplex stainless steel

DX2202 Duplex stainless steel Stainless Europe Grade DX22 Duplex stainless steel Chemical Composition Elements C Mn Cr Ni Mo N %.25.3 23. 2.5

More information

North American Stainless

North American Stainless North American Stainless Long Products Stainless Steel Grade Sheet AISI 310S S31008 EN 1.4845 AISI 314 S31400 EN 1.4841 INTRODUCTION Types 310S SS and 314 SS are highly alloyed austenitic stainless steels

More information

NORSOK STANDARD M-630 Rev. 4, January 2004

NORSOK STANDARD M-630 Rev. 4, January 2004 NORSOK STANDARD M630 Rev. 4, January 2004 Material data sheets for piping This NORSOK standard is developed with broad petroleum industry participation by interested parties in the Norwegian petroleum

More information

Application Datasheet

Application Datasheet Application Datasheet Standard Designation for Wrought Alloys Revision Date: June 2, 2016 s (C10100 - C15999) * = are alloys registered with the U.S. EPA as Antimicrobial. UNS # Cu Pb Zn Fe P Al Ag As

More information

DNV BUSINESS ASSURANCE MANAGEMENTSYSTEM CERTIFICATE

DNV BUSINESS ASSURANCE MANAGEMENTSYSTEM CERTIFICATE MANAGEMENTSYSTEM CERTIFICATE Certificate No. 137619--AQ-NLD-RvA This is to certify that A. park B.V. and its subsidiadies: A. B.V. A. B.V. A. B.V. A. B.V. H.J. Mertens B.V. Steenoven 2-6, 4196 HG Tricht,

More information

t.gainza, s.l. MOST COMMON QUALITIES AND THEIR EQUIVALENTS

t.gainza, s.l. MOST COMMON QUALITIES AND THEIR EQUIVALENTS CARBON STEELS ASTM A-105 1.0460 C22.8 DIN-17.243, EN-10.273 ASTM A-266 Gr-1,2,3,4 1.0436 P305 GH EN-10.222-2 (P245GH, P280GH) 1.0038 S235JRG2 EN-10.250-2 1.0116 S235J2G3 EN-10.250-2 1.0570 S355J2G3 EN-10.250-2

More information

Introduction to Iron Metallurgy. Lee Morin Houston Home Metal Shop Club October 2010

Introduction to Iron Metallurgy. Lee Morin Houston Home Metal Shop Club October 2010 Introduction to Iron Metallurgy Lee Morin Houston Home Metal Shop Club October 2010 Book I stole the pictures from We will start with a brief overview! Metals Are Crystals Fundamental geometry of a crystal

More information

The Stainless Steel Family

The Stainless Steel Family The Stainless Steel Family A short description of the various grades of stainless steel and how they fit into distinct metallurgical families. It has been written primarily from a European perspective

More information

North American Stainless

North American Stainless North American Stainless Flat Product Stainless Steel Grade Sheet 316 (S31600)/EN 1.4401 316L (S31603)/ EN 1.4404 INTRODUCTION NAS provides 316 and 316L SS, which are molybdenum-bearing austenitic stainless

More information

ASTM Material Specifications

ASTM Material Specifications ASTM Material Specifications The following is a chart from ANSI 16.34 1996 Version; Table 1 Material Specification Group 1 Materials Material Product Form Group No. Nominal Designation Forgings astings

More information

High Strength Steel (HSS) tubes for structural and engineering applications

High Strength Steel (HSS) tubes for structural and engineering applications High Strength Steel (HSS) tubes for structural and engineering applications 2 Tenaris produces a large dimensional range of seamless tubes in high strength steel for engineering and structural applications

More information

Anodes and Misc Equipment

Anodes and Misc Equipment Anodes and Misc Equipment Application: Platinised Titanium Anodes Platinised titanium anodes are recommended for use in the following electrolytic processes:- Precious metal electroplating - e.g. Au, Pt,

More information

North American Stainless

North American Stainless North American Stainless Flat Products Stainless Steel Sheet T409 INTRODUCTION NAS 409 is an 11% chromium, stabilized ferritic stainless steel. It is not as resistant to corrosion or high-temperature oxidation

More information

One stop shopping for any metal, cut and ready, fast!

One stop shopping for any metal, cut and ready, fast! ANGLES Data and Specifications 01 Aluminum Angles (Typically Rounded Corners) This is the most versatile of the heat treatable aluminum alloys. This alloy offers a wide range of mechanical properties and

More information

Duplex stainless steel for storage tanks

Duplex stainless steel for storage tanks Duplex stainless steel for storage tanks www.outokumpu.com 2 Why use Duplex stainless steels for storage tanks? Thanks to superior strength compared to standard stainless steels, Duplex lets you reduce

More information

TABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe. 4 Alloy Pipe & Tube. 6 Chrome-Moly Pipe. 7 Low-Temp Pipe

TABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe. 4 Alloy Pipe & Tube. 6 Chrome-Moly Pipe. 7 Low-Temp Pipe PRODUCT CATALOG TABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe 4 Alloy Pipe & Tube 6 Chrome-Moly Pipe 7 Low-Temp Pipe 9 Services amerpipe.com 1.800.316.5737 sales@amerpipe.com 18333

More information

AUSTENITIC STAINLESS DAMASCENE STEEL

AUSTENITIC STAINLESS DAMASCENE STEEL AUSTENITIC STAINLESS DAMASCENE STEEL Damasteel s austenitic stainless Damascene Steel is a mix between types 304L and 316L stainless steels which are variations of the 18 percent chromium 8 percent nickel

More information

MEDIUM & HEAVY PIPE GRADE C250 MANUFACTURING PROCESS GALVANISED FINISH STANDARD LENGTHS AUSTRALIAN STANDARDS THICKNESS AND MARKING

MEDIUM & HEAVY PIPE GRADE C250 MANUFACTURING PROCESS GALVANISED FINISH STANDARD LENGTHS AUSTRALIAN STANDARDS THICKNESS AND MARKING STEEL PIPE MEDIUM & HEAVY PIPE GRADE C250 MANUFACTURING PROCESS Grade C250 Pipe, for general mechanical and low pressure reticulation applications, is manufactured by cold-forming and high frequency Electric

More information

Welding of Stainless Steels

Welding of Stainless Steels Welding of Stainless Steels i Compiled/Edited by Richard D. Campbell, P.E. Welding Solutions, Inc., Broomfield, CO 1999 by American Welding Society. All rights reserved Printed in the United States of

More information

Enhanced version of 316/316L austenitic stainless steel. Better material performance at a lower cost. Juha Kela 16.6.2014. Juha Kela / 316plus

Enhanced version of 316/316L austenitic stainless steel. Better material performance at a lower cost. Juha Kela 16.6.2014. Juha Kela / 316plus Enhanced version of 316/316L austenitic stainless steel. Better material performance at a lower cost. Juha Kela 16.6.2014 8 July 2014 1 Lower cost 8 July 2014 2 Lower cost 316 plus is available at lower,

More information

INDEX ALUMINUM IN STEEL 7 BORON 3 CALCIUM IN STEEL 7 CARBON STEEL 3, 4 CAST IRON 20, 21, 22, 23, 24 COBALT ALLOY 14 GRAPHITIC CARBON 20 HIGH ALLOY STEEL 19 HIGH NICKEL STEEL 15 IRON 2 BRAMMER STANDARD

More information

ALLOY C276 DATA SHEET

ALLOY C276 DATA SHEET ALLOY C276 DATA SHEET //// Alloy C276 (UNS designation N10276) is a nickel-molybdenum-chromium-iron-tungsten alloy known for its corrosion resistance in a wide range of aggressive media. It is one of the

More information

Seamless stainless tubes for hydraulic and instrumentation systems

Seamless stainless tubes for hydraulic and instrumentation systems Seamless stainless tubes for hydraulic and instrumentation systems stock assortment integrated production technical knowledge network of sales and service Reduce your lifecycle costs When selecting tubes

More information

How to read your Oil Analysis Report

How to read your Oil Analysis Report How to read your Oil Analysis Report A better understanding Petroleum Technologies Group, LLC. 4665 Broadmoor S.E. Ste#15 Grand Rapids, MI 49512 Phone # 616/698 9399 Fax # 616/698 9395 www.oil lab.com

More information

Valve Steel. Valve Steel

Valve Steel. Valve Steel Valve Steel Valve Steel BÖHLER-UDDEHOLM Precision Strip AB is one of the world s leading manufacturers of high quality strip steel. More than a century s experience of cold rolling has given us a unique

More information

Heat Treating of Nonferrous Alloys

Heat Treating of Nonferrous Alloys Metallogr. Microstruct. Anal. (2013) 2:190 195 DOI 10.1007/s13632-013-0074-8 TUTORIAL Heat Treating of Nonferrous Alloys Howard E. Boyer Ó American Society for Metals 1984 The reader should understand

More information

Conductivity and Resistivity Values for Copper & Alloys

Conductivity and Resistivity Values for Copper & Alloys Conductivity and Resistivity Values for Copper & Alloys Material Conductivity Resistivity Reference Notes (% IACS) (Siemens/m) (Ohm-m) (See End Note) Copper and Copper Alloys by Copper Alloy Number Pure

More information

Base Materials (Fe Base Alloys And Superalloys)

Base Materials (Fe Base Alloys And Superalloys) 2 Base Materials (Fe Base Alloys And Superalloys) Chapter 2.1 BASE MATERIALS INTRODUCTION Materials which are very commonly employed in engineering applications are iron, iron base alloys, steels alloy,

More information