Important Loading Information. Tools Required. Meridian Lateral Files Instructions

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Important Loading Information. Tools Required. Meridian Lateral Files Instructions"

Transcription

1 Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information Any file system can tip if improperly used or loaded. Follow these simple guidelines for proper use. 1. Move files only when they are unloaded. 2. Distribute weight evenly. Load all files from the bottom drawer up. Do not leave the bottom drawers empty. Remove materials from the top drawers first. 3. When files are 68 or taller anchor files to each other (Side-to-Side) or to a structural wall (File-to-Wall). Tools Required Or Power Driver Phillips Screwdriver 3/8 Socket 3/8 Wrench 5/16 Allen Wrench Rubber Mallet Carpenter s Level 2015 Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 1

2 Procedures A. Leveling Locking Tab 1. Place file in desired location. Slide Slide 2. Pull bottom drawer all the way out. Working one side at a time, press drawer sides in toward center of file so locking tabs clear drawer slides. Locking Tab Slide Slide 3. Making sure that locking tabs clear drawer slides, lift drawer from slide and remove drawer from file Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 2

3 Glide 4. Using 5/16 Allen wrench, turn leveling glides clockwise to raise corner, counterclockwise to lower corner. 5. Check for side-to-side and front-to-back leveling. Once level, turn the two front leveling glides 1/4 turn clockwise. Drawer Tab Slide Slot 6. Working one side at a time, replace drawer by aligning both drawer tabs with corresponding slide slots and pushing down until locking tabs snap into place Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 3

4 B. Side-to-Side Anchoring- For to High or Taller To anchor files side-to-side, work from the right hand file. For tight junctions, repeat the procedure, described below, in the top, middle and bottom modules. Service Part Hardware Kit U1B36D9 is required. Note: 1 high modules (N,E,F,D,P,L & H) without counter weights. Need to be ganged back to back or anchored to floor. 1. Place files side-to-side in desired location, and adjust leveling glides as shown in Steps 1-5 in Section A. Modules to be anchored 2. From the right hand file, remove the drawers from the modules that will be anchored Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 4

5 Top Hole Front Vertical Frame 3. Using the Power Driver, drive one drill-point screw through the top hole in the front vertical frame and into the adjacent file. Take care to not over tighten. Rear Vertical Frame Centered 4. Drive a second drill-point screw, centered from top to bottom, in the slot in the rear vertical frame, into the adjacent file. Take care to not over tighten. 5, Repeat steps 1-4 for each remaining module Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 5

6 C. File-to-Wall Anchoring NOTE: Proper Anchoring is the responsibility of the Installer/User. 1. Place file in desired location and adjust leveling glides as shown in Steps 1-5 in Section A. 2. Use fasteners appropriate for the wall construction. For plaster or dry wall construction use moly bolts with metal washers. For best installation, anchor each file to wall studs Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 6

7 D. Joining and Aligning Add-On Sections NOTE: 78 and higher files are shipped in two sections. Joining the sections may require two people. 1. Remove and discard shipping cleats. 2. Remove top drawer from the Lower Section and bottom drawer from the Add-On Section, as shown in Steps 1-3 of Section A. Interlock Bar 3. At the left side of both sections, rotate interlock bars to the rear. Lower Interlock Bar Upper Interlock Bar 4. Obtain Upper Interlock Bar and Lower Interlock Bar from Hardware Kit Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 7

8 Add-On Section Interlock Bar Lower Interlock Bar Upper Interlock Bar Interlock Bar Lower Section 5. Place add-on section onto lower section while aligning and joining Upper and Lower Interlock Bars. Rotate interlock bars to be sure they turn smoothly Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 8

9 6. From the hardware pack, insert one hex head bolt in each corner hole and one in the center rear hole. Thread nuts on bolts loosely. Alignment Area Rubber Mallet 7. Align the sections at the front and sides. If force is required, apply a rubber mallet only to the alignment area, shown. 8. After aligning, tighten nuts onto the hex head bolts Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 9

10 Add-On Section Splicer Lockbars Lower Section 9. On the right side, connect splicer, provided in hardware pack, between the lockbars, pressing firmly until splicer snaps into place. 10. Replace drawers as shown in Step 6 of Section A Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 10

11 E. Separating and Reversing 2600 Series Files NOTE: Observe the following conditions for reversing sections. One Section Reversed Two Section Reversed Correct Incorrect - To prevent instability, reverse only as shown in the correct configuration above. Only one change of drawer opening direction is allowed per file cabinet. - Reversed file cabinets can be anchored to a structural wall or in-line file-to-file, as shown in Sections B and C, preceding. - For a reversed section, order one reversing hardware pack (#100/011) from Herman Miller Inc. Section to be reversed Remove these drawers 1. Remove drawers above and below the point where sections will be separated and reversed Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 11

12 Splicer 2. Remove lockbar splicer. 3. Remove the five (5) attaching hex head bolts and nuts. Upper Interlock Bar Interlock Bar 4. Push the Interlock Bar down and away from the side. Slide the Upper Interlock Bar down and remove it. 5. Reverse the separated section Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 12

13 6. Align the sections at the front and sides. If force is required, see Section D, Step Align the bolt holes of the upper and lower sections. Re-install four (4) hex head bolts and nuts; two at each side of file, as shown above. NOTE: Interlock bars not shown for clarity of illustration. Upper (Reversed) Section Upper (Reversed) Section Lower Section Drill-point screw (here, and at opposite corner) Drill-point screw (here, and at opposite corner) Lower Section 8. From the hardware pack, install four (4) drill-point screws, two (2) from Lower Section, going up and two (2) from Upper Section, going down Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 13

14 Upper Section Interlock Channel Top Module of Lower Section Top Interlock piece (with spring) Interlock Bar 9. To activate interlocking in the Top Module of the Lower Section, obtain the Top Interlock piece (with spring) from the hardware pack. Slide Top Interlock piece up the Interlock channel. Swing the Interlock Bar in and engage it. Bottom Module of Upper Section Interlock Bar Lower Section Interlock Channel Bottom Interlock piece 10. To activate interlocking in the Bottom Module of the Upper Section, obtain the Bottom Interlock piece (with spring) from the hardware pack. Slide the Bottom Interlock piece down into the Interlock channel. Swing the Interlock Bar in and engage it. 11. Check for free rotation of Interlock bars and make sure a Splicer (see Step 9, Section D) connects all Lockbars that face the same direction Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 14

15 Y Meridian Storage Towers and Lateral Files Caster Installation and Disassembly for Recycling Instructions Parts Included: A B C D A Tools Required: B Safety Glasses D C 2015 Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 15

16 1. For lateral files: Remove shipping cleats from base and dispose of properly. 2. Place base on its side on clean surface. Position both fixed casters at same end of base and both swivel casters at opposite end. 3. Attach all casters to base with self tapping screws provided using power torqure driver and 3/8 nutdriver bit. 4. For towers: Remove shipping cleats from base and dispose of properly. 5. Place base on its side on clean surface. Position both locking swivel casters on front of tower base & swivel casters in rear of tower base. 6. Attach all casters to base with self tapping screws provided using power torque driver and 3/8 nutdriver bit Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 16

17 Disassembly for Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling. Non-ferrous metals should be separated and recycled separately. To disassemble product, reverse steps 6 through Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. 17

Fundamental Assembly Instructions

Fundamental Assembly Instructions Fundamental Assembly Instructions 1998757 Revision A-11 Complete Series Master Packet 2008 Kimball International, Inc. T 800.482.1818 F 812.482.8300 Footprint Storage and Metal Filing Systems Assembly

More information

Lista Shelf Converter Assembly Instructions for Multiple Shelving Applications

Lista Shelf Converter Assembly Instructions for Multiple Shelving Applications Lista Shelf Converter Assembly Instructions for Multiple Shelving Applications Table of Contents Safety Check List...2 Existing Shelving Assembly Notes...3 Three Basic Assembled Types...3 Recommended Drawer

More information

HermanMiller Aeron Posturefit Installation AE905A AE905B AE905C

HermanMiller Aeron Posturefit Installation AE905A AE905B AE905C HermanMiller Aeron Posturefit Installation AE905A AE905B AE905C Y How to assemble to your chair Parts Included Posturefit Mechanism For more information about our products and services or to see a list

More information

Chapter 3 Assembling the Storage Ladder

Chapter 3 Assembling the Storage Ladder Chapter 3 Assembling the Storage Ladder This chapter provides step-by-step instructions for assembling and attaching the Safety Ladder to the Storage Wall. General Information The Lista Safety Ladder provides

More information

WALL-MOUNT WASH STATION

WALL-MOUNT WASH STATION YOU WILL NEED: Phillips Screwdriver Leveling Device Drill 5/32 inch Hex Key Drill Bits: 1/4 inch (6.4 mm) 1/2 inch (13 mm) Power Screwdriver With Phillips Bit Shims (provided in hardware kit) R A-DEC INC.

More information

Tools Required: Materials Identification and Segregation: Disassembly Steps: Setu Disassembly for Recycling

Tools Required: Materials Identification and Segregation: Disassembly Steps: Setu Disassembly for Recycling Y Setu Disassembly for Recycling Tools Required: 2 lbs Hammer T-20 Torx Driver T-27 Torx Bit (2.75 or longer) Power Driver Small Flathead Screwdriver Safety Glasses Utility Knife Rubber Mallet Materials

More information

Canvas Office Landscape Wall Strip Installation and Disassembly for Recycling Instructions

Canvas Office Landscape Wall Strip Installation and Disassembly for Recycling Instructions Y Parts Included: Canvas Office Landscape Wall Strip Installation and Disassembly for Recycling Instructions Tools Required: Power Driver Drill Bit (Determined by fastener) Driver Bit (Determined by fastener)

More information

STACKABLE FILE CABINETS

STACKABLE FILE CABINETS REVISED STACKABLE FILE CABINETS Wooden file cabinets are possibly the only kind worthy of being called furniture. These stackables can grow as your files do. Since each drawer is modular, you can order

More information

Rollator Cane and Brake Replacement SAFETY SUMMARY (CONTINUED)

Rollator Cane and Brake Replacement SAFETY SUMMARY (CONTINUED) Rollator Cane and Replacement Assembly, Installation and Operating Instructions SAVE THESE INSTRUCTIONS NOTE: Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use. Contact Carrier/Dealer

More information

Seismic Installation for Attic Storage System

Seismic Installation for Attic Storage System Your Performance Partner Seismic Installation for Storage System CONTENTS SSafety Precautions................................. 2 Required Tools..................................... 2 Parts and Fastener

More information

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware

More information

KEYPAD LOCK RETROFIT KIT

KEYPAD LOCK RETROFIT KIT KEYPAD LOCK RETROFIT KIT INSTRUCTIONS FOR ASSEMBLY IMPORTANT READ & SAVE THESE INSTRUCTIONS Tools Required for Assembly 5/32 hex (Allen) wrench #2 Phillips screwdriver Isopropyl alcohol or alcohol wipes

More information

Cable Drum Installation

Cable Drum Installation 20 Cable Drum Installation COUNTERBALANCE None Shake the TorqueMaster spring tube gently to extend the winding shafts out about 5" on each side. For single spring applications, there will be no left hand

More information

Hanson Offroad 6951 McDivitt Dr. Bakersfield CA 93313 U.S.A. 877-757-9779

Hanson Offroad 6951 McDivitt Dr. Bakersfield CA 93313 U.S.A. 877-757-9779 Remove stock bumper. Retain the stock bolts that attached the bumper to the sides of the frame. There are four holes in the back of the frame. You will need to enlarge the far right hole using a drill

More information

Assembly Instructions for Model: VMSA

Assembly Instructions for Model: VMSA Assembly Instructions for Model: VMSA Thank you for choosing a Sanus Systems Vision Mount wall mount. The VMSA is designed to mount up to 50 [1270 mm] Flat panel televisions weighing up to 150 lbs. [68.2

More information

BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS

BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE

More information

DROP LEAF KITCHEN CART WITH BASKETS. Model 72265

DROP LEAF KITCHEN CART WITH BASKETS. Model 72265 DROP LEAF KITCHEN CART WITH BASKETS Model 72265 Parts List (6) BASKET GLIDES (2) BOTTOM FRONT & BACK BRACES (2) DRAWER SUPPORT STICK (1) TOP BACK BRACE (2) SIDE PANELS (1) TOP FRONT BRACE (2) DROPLEAF

More information

Triple Threat 3-in-1 Game Table 3 IN 1 GAME TABLE

Triple Threat 3-in-1 Game Table 3 IN 1 GAME TABLE NG0M Triple Threat 3-in- Game Table 3 IN GAME TABLE Thank 3 in Y Game Table Thank you for your purchase of our product. We work around the clock and around the globe to ensure that our products maintain

More information

INSTALLATION INSTRUCTIONS ELEVATION REAR BUMPER RAM

INSTALLATION INSTRUCTIONS ELEVATION REAR BUMPER RAM INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 4 8mm x 40mm Hex Bolts 1 Universal License Plate Light 4 8mm x 28mm x 3mm Flat Washers 8 12-1.75mm x 50mm Hex Bolts 4 8mm Lock Washers

More information

Speed-Mat Rectangle Cutter

Speed-Mat Rectangle Cutter Speed-Mat Rectangle Cutter 1 Honeycomb baseboard. 2 Left hold down. 14 3 Bottom hold down. 4 4 Left / right rule. 8 5 8 5 Left / right rule pointer. 1 6 Top / bottom rule. 7 Top / bottom rule pointer.

More information

INSTRUCTIONS: LocknCharge Laptop Carts

INSTRUCTIONS: LocknCharge Laptop Carts INSTRUCTIONS: LocknCharge Laptop Carts www.lockncharge.com Extra Tools required: Hammer, Philips head screwdriver, medium adjustable spanner. (Allen key supplied) (Panel colours for illustration purposes

More information

Installing the Cart Garage Frame and Flush Door

Installing the Cart Garage Frame and Flush Door General Information: The following provides step-by-step instructions for assembling and installing the Automotive Cart Garage Frame and Door under a work surface. The finished assembly will consist of

More information

VERTICAL BLINDS GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE

VERTICAL BLINDS GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE VERTICAL BLINDS GETTING STARTED OPTIONAL HARDWARE A few simple tools are required: Corner End Cap Plastic Corner Aluminum Corner Steel Tape Measure Pencil Level (for outside mount) valence Return Corner

More information

Bunk Bed Assembly Instructions

Bunk Bed Assembly Instructions Bunk Bed Assembly Instructions Thank you for your purchase of a smartstuff bunk bed. smartstuff bunk beds are designed, engineered and certified to meet the safety guidelines of the Consumer Product Safety

More information

42U/45U 28" Wide Rack Installation & Service Guide

42U/45U 28 Wide Rack Installation & Service Guide 42U/45U 28" Wide Rack Installation & Service Guide 96-00171-005 Rev B Important Information Information in this document is subject to change without notice and does not represent a commitment on the part

More information

KDT916 - Watts Link - Complete Assembly

KDT916 - Watts Link - Complete Assembly KDT916 - Watts Link - Complete Assembly Please read all instructions carefully prior to installation and verify all kit contents and tools are on hand prior to installation. Professional Installation by

More information

Basic Spring Motor Roller Shades

Basic Spring Motor Roller Shades Comprehensive Roller Shade Installation Guide Basic Spring Motor Roller Shades ATTENTION!!! READ CAREFULLY! This shade has a reliable long-lasting Spring Motor. The Spring Motor must have proper tension

More information

OWNER S MANUAL Table Tennis Table Patent Pending

OWNER S MANUAL Table Tennis Table Patent Pending OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179

More information

Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors

Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors Installation Manual Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors SW602206 Rev B Table of Contents Chapter 1: Safety Warning... 3 Chapter 2: Kit Contents... 4 Included in Kit...

More information

WARNING: Important: Keep these instructions for future reference. Gate Instructions (1) Assembly and Installation Instructions

WARNING: Important: Keep these instructions for future reference. Gate Instructions (1) Assembly and Installation Instructions Assembly and Installation Instructions Please read these instructions carefully. Please follow these instructions carefully to ensure that your gate extension is properly installed. Improper installation

More information

TABLE OF CONTENTS CABINET SAFETY

TABLE OF CONTENTS CABINET SAFETY CABINET SAFETY...2 ASSEMBLY INSTRUCTIONS...3 Tools and Parts...3 Cabinet Use Requirements...3 Unpack the Cabinet...3 TABLE OF CONTENTS CABINET SAFETY Install the Bumper...3 Install the Casters...4 Install

More information

1.8 CRANKSHAFT OIL SEALS

1.8 CRANKSHAFT OIL SEALS SERIES 60 SERVICE MANUAL 1.8 CRANKSHAFT OIL SEALS An oil seal is fitted between each end of the crankshaft and the bores of the flywheel housing and gear case cover to retain the lubricating oil in the

More information

INSTALLATION INSTRUCTIONS for Bifold Doors (JII103)

INSTALLATION INSTRUCTIONS for Bifold Doors (JII103) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Turbo Tube Slide INSTALLATION INSTRUCTIONS C A U T I O N Do not climb on the outside of the slide This slide is designed for home use only, not for Public Playgrounds PlayCore, Inc. 2004 Copyrighted Material.

More information

FLATBED TRAILER WITH ATV TIRES

FLATBED TRAILER WITH ATV TIRES FLATBED TRAILER WITH ATV TIRES Model 47845 ASSEMBLY and OPERATING INSTRUCTIONS Note: Wooden stake panels are not included. Wooden Stake Kit, #40041 is sold separately. Flatbed Trailer is for off-road use

More information

All-Season Sunroom Sliding Glass Door Installation Instructions

All-Season Sunroom Sliding Glass Door Installation Instructions ASRESGD-08 All-Season Sunroom Sliding Glass Door Installation Instructions Panel Frame Door Frame Left Side Foam Insulator IE241 H Bar Assembly Door Frame Top Track Panel Frame Door Frame Right Side Stationary

More information

CEILING FAN OWNER'S MANUAL

CEILING FAN OWNER'S MANUAL CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS MODEL: 52P-646-5RV-187 52P-646-5RV-323 FAN RATING AC 120V. 60Hz CUL LISTED MODEL : AC-552A 1. TOOLS AND MATERIALS REQUIRED Philips screw driver

More information

POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS

POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS Polemount Field Fix Support If you have any questions or incur any problems installing or using the new Polemount, please use Miovision s Support System by emailing

More information

Rebuild Instructions for 70001 and 70010 Transmission

Rebuild Instructions for 70001 and 70010 Transmission Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before

More information

MP8000 Series Pneumatic Valve Actuators

MP8000 Series Pneumatic Valve Actuators 14-1161- 9, Rev. A Technical Bulletin MP8000 Issue Date March 2016 MP8000 Series Pneumatic Valve Actuators Pre-Assembly Details Page 3 MP8000 Actuator Components 3 Tools Required to Assemble an MP8000

More information

REAR BUMPER INSTALLATION INSTRUCTIONS TOYOTA TACOMA 05-10 (WITH STOCK HITCH)

REAR BUMPER INSTALLATION INSTRUCTIONS TOYOTA TACOMA 05-10 (WITH STOCK HITCH) Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 REAR BUMPER INSTALLATION INSTRUCTIONS TOYOTA TACOMA 05-10 (WITH STOCK HITCH) Please read before beginning Stainless steel hardware

More information

Installation Manual TWM Performance Short Shift Kit 2005 and up Scion TC

Installation Manual TWM Performance Short Shift Kit 2005 and up Scion TC Installation Manual TWM Performance Short Shift Kit 2005 and up Scion TC 1. Unscrew the shift knob by rotating counter clockwise, set it aside for now. 2. Remove the portion of the console with the shift

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic

More information

Chelsea Loft Bed WARNING:

Chelsea Loft Bed WARNING: Chelsea Loft Bed WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS FOR FUTURE

More information

Aluminum Trailer Kit Assembly Overview

Aluminum Trailer Kit Assembly Overview Aluminum Trailer Kit Assembly Overview VERY IMPORTANT: ALWAYS REFER TO YOUR OWNER S MANUAL FOR PROPER OPERATING AND SAFETY INFORMATION REGARDING YOUR TRAILER & PARTS LIST. Step 1: Remove All Parts Remove

More information

Installation Instructions Complete Top Frame & Hardware With Soft Upper Doors Jeep Wrangler

Installation Instructions Complete Top Frame & Hardware With Soft Upper Doors Jeep Wrangler Installation Instructions Complete Top Frame & Hardware With Soft Upper Doors 87-95 Jeep Wrangler IMPORTANT NOTICE: Carefully read instructions before attempting to install this product. Rampage Products

More information

PRODUCT: TJ/LJ Rear Bumper & Tire Carrier READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL M-F 7:00 AM 5:00 PM PST

PRODUCT: TJ/LJ Rear Bumper & Tire Carrier READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL M-F 7:00 AM 5:00 PM PST PRODUCT: TJ/LJ Rear Bumper & Tire Carrier READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL 916-631-8071 M-F 7:00 AM 5:00 PM PST REV: C 06-29-2015 II-2841 The MetalCloak experience includes

More information

GATEWAY NOTEBOOK SERVICEGUIDE

GATEWAY NOTEBOOK SERVICEGUIDE GATEWAY NOTEBOOK SERVICEGUIDE Contents Replacing Notebook Components................................... 1 Identifying the notebook model........................................ 2 Identifying components..............................................

More information

Unpacking, Installation, and Customization

Unpacking, Installation, and Customization Unpacking, Installation, and Customization NetShelter WX Enclosure AR100 AR100HD Contents Unpacking... 1 How to Unpack the Enclosure............................... 1 Please Recycle..........................................

More information

MGB Chrome Bumper Conversion

MGB Chrome Bumper Conversion MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different

More information

Installation Instructions 4508 4508S

Installation Instructions 4508 4508S SYMPHONY Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure

More information

ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES

ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR FIBER OPTIC CONTACTS AND MODULES Table of Contents SECTION 1 CONTACT INSTALLATION AND REMOVAL SECTION 2 MODULE INSTALLATION AND REMOVAL SECTION

More information

SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #7200

SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #7200 SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #7200 ROLLGUARD A-FRAME LADDER LADDER MUST BE ATTACHED TO POOL FRAME. DO NOT USE WITH INFLATABLE POOLS ASSEMBLY AND INSTALLATION MANUAL

More information

Installation Instructions for DCI Edge Over the Patient Delivery System

Installation Instructions for DCI Edge Over the Patient Delivery System Table of Contents Page Unit Installation Notes 2 Post Wall/Cabinet Mount Installation 3 Delivery System Installation 3 Self Contained Water System Installation 4 Self Contained Water System Schematic 5

More information

Lincoln Mark VII Power Window Motor Repair

Lincoln Mark VII Power Window Motor Repair Lincoln Mark VII Power Window Motor Repair Is your door no longer going up and down? Does the window motor make a horrible sound when in use? Does your window no longer work at all? You may need to replace

More information

Dell P Series Monitor VESA Mounting Bracket Installation Instructions

Dell P Series Monitor VESA Mounting Bracket Installation Instructions Dell P Series Monitor VESA Mounting Bracket Installation Instructions The VESA mounting bracket enables a Wyse cloud client to be mounted to the Dell P Series Monitor and the Dell E24 Monitor. The cloud

More information

Standard Royal Inspiration Station

Standard Royal Inspiration Station IS2 Standard Royal Inspiration Station R Assembly uide IS2_2013_A Check out our other products online at www.copernicused.com or assistance, please contact us: 1-800-267-8494 Email info@copernicused.com

More information

Front brakes (FN- 3), servicing

Front brakes (FN- 3), servicing j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly

More information

CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6

CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 Pre-Installation Notes: The CorkSport Rear Sway Bar is a great addition to improving the handling performance to the Mazdaspeed 6. It will minimize

More information

Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN

Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN Installation Instructions Structural Information For standard systems and most custom single door opening systems. General Overview

More information

Express5800/120Ed. Rack Mount Kit Installation Procedures PN: 455-01607-001

Express5800/120Ed. Rack Mount Kit Installation Procedures PN: 455-01607-001 Express5800/120Ed Rack Mount Kit Installation Procedures PN: 455-01607-001 Proprietary Notice and Liability Disclaimer The information disclosed in this document, including all designs and related materials,

More information

Panel Track Installation Guide

Panel Track Installation Guide Panel Track Installation Guide We make it easy! BTG 493361 EN_0510 Before starting Your new Blinds To Go panel track is custom made to your specifications from the finest materials available. To ensure

More information

Parts List. Safety Information. Additional Considerations. Retractable Security Cover Kit. Rocky Roller Kit

Parts List. Safety Information. Additional Considerations. Retractable Security Cover Kit. Rocky Roller Kit Parts List Retractable Security Cover Kit 3" PVC pipe with (4) 7'4" lengths of track (longer pools will have additional track pieces) Leading edge Optional cover pump (for outdoor installations) Rocky

More information

Part # 11060210 59-64 Impala SA CoilOver Suspension Package

Part # 11060210 59-64 Impala SA CoilOver Suspension Package 350 S. St. Charles St. Jasper, In. 47546 Part # 11060210 59-64 Impala SA CoilOver Suspension Package Front Components: 1 11053510 HQ Series Front Coilovers 1 11052899 Front Lower StrongArms 1 11053699

More information

Assembly & Installation Instructions

Assembly & Installation Instructions S O U T H W E S T W I N D P O W E R RV Telescoping Tower Owner s Manual Assembly & Installation Instructions 1) Before Installation 1-1 Package Contents 1-2 Items Not Included 1-3 Required Tools 2) Base

More information

Extendable Trailer Towing Mirror

Extendable Trailer Towing Mirror Extendable Trailer Towing Mirror Installation Instructions For: 1997-2001 Ford F150 CIPA Part Numbers 72000 & 82000 WARNING Manufacturer recommends this installation be carried out by a professional installer

More information

Structural Holding System

Structural Holding System Structural Holding System Users Manual November 2013 by Vehicle Service Group. All rights reserved. CO8812.1 502071 Rev. - 11/21/2013 CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies

More information

INSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AD Last Updated: 12/03/13 US PATENT: D683,281 CHINESE PATENT: ZL

INSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AD Last Updated: 12/03/13 US PATENT: D683,281 CHINESE PATENT: ZL PREMIUM FRONT BUMPER AEV30103AD Last Updated: 12/03/13 US PATENT: D683,281 CHINESE PATENT: ZL 2012 3 0026032.0 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND

More information

Table of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.

Table of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing. www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing

More information

TS93 EMR T/PT/TDE. Surface applied door closer

TS93 EMR T/PT/TDE. Surface applied door closer TS EMR T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer with smoke detector (EMR T) Push side track mount door closer with smoke detector (EMR PT) Double

More information

INTRODUCTION INTERLOCK KIT K-8110

INTRODUCTION INTERLOCK KIT K-8110 INTRODUCTION INTERLOCK KIT K-8110 This manual provides instructions for safe installation of the InterLock Kit onto a General Electric (GE) panel. The back plate sits securely on the face of the panel

More information

Linear Incline Hook- on Shelves

Linear Incline Hook- on Shelves Linear Incline Hook- on Shelves Tools Required -Plastic Mallet -Phillips head screwdriver -Flat blade screwdriver 1. Assemble the Front Stop to the shelf, using the #10AB x 1-3/4 phillips pan head thread

More information

WINDOW REPAIR MANUAL & REFERENCE GUIDE

WINDOW REPAIR MANUAL & REFERENCE GUIDE WINDOW REPAIR MANUAL & REFERENCE GUIDE TABLE OF CONTENTS DOUBLE HUNG & SINGLE HUNG PARTS 4-5 CASEMENT PARTS 6 SCREEN PARTS 7-8 HOW TO REMOVE TILT-IN SASH 9 HOW TO REMOVE A BALANCE 10 HOW TO INSTALL BALANCE

More information

WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS

WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS Instruction Booklet 18 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE

More information

BUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS

BUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS BUTTERFLY SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,

More information

Mazda MX-5 Soft Top Installation Instructions

Mazda MX-5 Soft Top Installation Instructions Mazda MX-5 Soft Top Installation Instructions These instructions show how to replace your soft top with the frame remaining attached to the car. This requires the use of a right angled driver which is

More information

5800 Temperature Sensor Cable Assembly

5800 Temperature Sensor Cable Assembly 5800 Temperature Sensor Cable Assembly Removal and Replacement Instruction Sheet #60-4702-070 Revision D, January 14, 2013 Overview The 5800 has two refrigeration temperature sensors, one attached to the

More information

2011 FORD SUPERDUTY F-250/350 4WD CSS-F3-9, CSS-F3-10 4.5 LIFT KIT

2011 FORD SUPERDUTY F-250/350 4WD CSS-F3-9, CSS-F3-10 4.5 LIFT KIT 14385 Veterans Way Moreno Valley, CA 92553 Phone: (951) 571-0212 Fax: (951) 571-0215 WWW.CSTSUSPENSION.COM 2011 FORD SUPERDUTY F-250/350 4WD CSS-F3-9, CSS-F3-10 4.5 LIFT KIT READ THE FOLLOWING NOTES PRIOR

More information

BODY-12, Door Handle - Removal, Installation, and Adjustment

BODY-12, Door Handle - Removal, Installation, and Adjustment Introduction BODY-12, Door Handle - Removal, Installation, and Adjustment There are many different procedures floating around describing how to replace the door handles on a 944 and every one of them will

More information

Installation Instructions Kit, Base Rail Bracket Part # 31404

Installation Instructions Kit, Base Rail Bracket Part # 31404 Installation Instructions Kit, Base Rail Bracket Part # 31404 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions. provide important operating and

More information

LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963

LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 Thank you for purchasing LG Motorsports products for your Gen 5 Camaro. Parts Inventory:

More information

BUNK BED. Model No.: DA3797E - Espresso DA3797P- Pine. UPC CODE: 0-65857-16117-5 (Espresso) 0-65857-16116-8 (Pine) NOTE: Lot number: Date of purchase:

BUNK BED. Model No.: DA3797E - Espresso DA3797P- Pine. UPC CODE: 0-65857-16117-5 (Espresso) 0-65857-16116-8 (Pine) NOTE: Lot number: Date of purchase: BUNK BED Model No.: DA3797E - Espresso DA3797P- Pine UPC CODE: 0-65857-16117-5 (Espresso) 0-65857-16116-8 (Pine) NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP

More information

Item #: BTOT Assembly Instructions

Item #: BTOT Assembly Instructions Item #: BTOT Assembly Instructions For our most current instructions, to request missing, lost or broken parts, or for any other Customer Service issues, please visit our website at www.walkeredison.com

More information

CABLEVIEW RAILING INSTRUCTIONS

CABLEVIEW RAILING INSTRUCTIONS CUSTOMER SERVICE CONTACT INFO Phone: 888-686-7245(RAIL) Fax: 888-686-7245 (RAIL) Email: sales@stainlesscablerailing.com Website: www.stainlesscablerailing.com Address: 3315 NE 112 th Ave #72/73, Vancouver,

More information

Lunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide

Lunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your

More information

pottery barn kids THOMAS BUNK BED WARNING:

pottery barn kids THOMAS BUNK BED WARNING: pottery barn kids THOMAS BUNK BED WARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS

More information

Vertical Window Blinds Installation

Vertical Window Blinds Installation Vertical Window Blinds Installation How to Install Vertical Window Blinds Congratulations on your purchase of a vertical window blind. Your blind has been custom made to your specifications and is one

More information

Standard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm)

Standard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm) Standard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm) 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com

More information

MODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER

MODEL# SLA001-3 SLIDE & LOCK A-FRAME POOL LADDER MODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER IMPORTANT INSTRUCTIONS: : Read all instructions carefully & completely to become familiar with parts, assembly, safety and proper use of this product.

More information

Kiosk Group, Inc. ASSEMBLY INSTRUCTIONS FOR THE STANDALONE. EXQUISITE ipad KIOSK. For ipad 2-3-4-5 Version Tablets.

Kiosk Group, Inc. ASSEMBLY INSTRUCTIONS FOR THE STANDALONE. EXQUISITE ipad KIOSK. For ipad 2-3-4-5 Version Tablets. Kiosk Group, Inc. ASSEMBLY INSTRUCTIONS FOR THE STANDALONE EXQUISITE ipad KIOSK For ipad 2-3-4-5 Version Tablets ipad 2-3-4-5 Version Tablet Items Required: ipad data/power cable that came with your ipad.

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (741-644) Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, GMC Yukon, Chevrolet Silverado, GMC Sierra 2000 05 General Tech Tips: Use painter s tape rather than

More information

Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement

Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations

More information

In-Ground Basketball System Owners Manual

In-Ground Basketball System Owners Manual In-Ground Basketball System Owners Manual Customer Service Center N53 W4700 South Corporate Circle Sussex, WI 53089 U.S.A. Write Model Number From Box Here: WARNING! 3 Capable Adults REQUIRED TOOLS AND

More information

HOME RAIL INSTALLATION GUIDE

HOME RAIL INSTALLATION GUIDE HOME RAIL INSTALLATION GUIDE Parts Parts : - Top and Bottom Rail Pack - End posts, Line posts, Corner Posts, Blank Posts, 6 ft posts 45 degree post ( need bracket ) - Picket and clip Pack - Glass Channel

More information

* * AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS

* * AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS 16 1 AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light

More information

DYNA RIDER FOOTBOARD KIT

DYNA RIDER FOOTBOARD KIT -J0 REV. 0-0-0 DYNA RIDER FOOTBOARD KIT GENERAL Kit Number 000 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English

More information

SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V

SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V INSTALLATION GUIDE for the SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox be properly mounted to the

More information

Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006

Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering

More information

Fresenius Medical Care North America Service Bulletin

Fresenius Medical Care North America Service Bulletin Fresenius Medical Care North America Service Bulletin Equipment: Bulletin: Subject: 2008 K Hemodialysis Machines 15-FRK-001 Rev A Optional Shunt Box Ferrite Core Installation (Update) 1.0 PURPOSE To inform

More information