C C1 C2 AL1 AL2 AL3. Micro-controller X. Model: PXR4/5/7/9 SEL PXR. Operation Manual. ECNO:406f

Size: px
Start display at page:

Download "C C1 C2 AL1 AL2 AL3. Micro-controller X. Model: PXR4/5/7/9 SEL PXR. Operation Manual. ECNO:406f"

Transcription

1 C C1 C2 AL1 AL2 AL3 Micro-controller X Model: PXR4/5/7/9 PXR SEL Operation Manual ECNO:46f

2 Table of Contents Part Names and Functions... 6 Operations Parameter list Basic operations Parameter functions and method of settings Manual mode setting Standby setting Local/remote operation setting Ramp-soak control Canceling the alarm latch Au-tuning function... 2 ing ON-delay alarm or the remaining time of timers Setting alarm 1, 2 and Upper limit of alarm 1, 2 and Lower limit of alarm 1, 2 and Key lock Proportional band Integral time Derivative time Hysteresis range for ON/OFF control Cooling-side proportional band coefficient Cooling-side proportional band shift (Dead band/overlap band) Output offset value... 3 Anti-reset windup... 3 Control algorithm (Measured value) stable range HYS (Hysteresis) mode at ON/OFF control Cycle time of control output Cycle time of control output 2 (Cooling-side) Input signal code Setting the measuring range (Input range)... 4 Selection C / F... 4 Decimal point position (Measured value) offset (Setting value) offset Time constant of input filter Alarm types Selecting ramp-soak patterns Ramp-soak status display st 8th target st 8th ramp segment time st 8th soak segment time... 5 Ramp-soak modes

3 Specifying control action and output direction at input burn-out (Setting value) lower limiter (Setting value) upper limiter The time of ON-delay alarm or timer function ing current detecr input HB (Set value of heater break alarm) Hysteresis alarm 1, 2 and Options of alarm 1, 2 and Upper and lower limits for control output Upper and lower limits for control output Output limit types Output value display RCJ (Cold junction compensation) Adjusting the (Measured value) display (%) Adjusting the (Measured value) display (1%) DI1/2 (Digital input 1/2) operation Station No. for communication... 7 Parity for communication Communication procol setting Re-transmission output type setting Re-transmission base and span scale Remote input (%) adjustment Remote input (1%) adjustment Remote input filter constant Remote input value display Parameter display mask Troubleshooting Index

4 PXR4, PXR7 PXR Digit Specification Note 4 <Front dimensions> 48 X 48mm 72 X 72mm 5 <Input signal> Thermocouple C Thermocouple F Resistance bulb Pt1 3-wire type C Resistance bulb Pt1 3-wire type F 1 5V DC 4 2mA DC 6 <Control output 1> Relay contact output Voltage pulse output (24V DC) 4 2mA DC output Note 1 7 <Control output 2> None Relay contact output Note 2 Voltage pulse output (24V DC) Note 2 4 2mA DC output Note 2 Re-transmission output (4 2mA DC) Note 2 8 <Revision code> 9 <Optional specifications 1> None Alarm (1 pc.) Alarm for heater break Note 3 Alarm (1 pc.) + Alarm for heater break Note 3 Ramp-soak Alarm (1 pc.) + Ramp-soak Alarm for heater break + Ramp-soak Note 3 Alarm (1 pc.) + Alarm for heater break + Ramp-soak Note 3 Alarm (2 pcs.) Alarm (2 pcs.) + Ramp-soak Alarm (2 pcs.) + Alarm for heater break + Ramp-soak Note 3 Alarm (3 pcs.) Remote Note 3 Remote + Alarm (2 pcs.) Note 3 1 <Instruction manual> <Power supply voltage> None 1 24V AC English 1 24V AC None 24V DC English 24V DC 11 <Optional specifications 2> 12 None 13 RS485 (Modbus) communication RS485 (ASCII) communication Digital input 1 point Digital input 2 points Note 4 RS485 (Modbus) communication + Digital input 1 point RS485 (ASCII) communication + Digital input 1 point 4 7 T R N S A B A C E Y A C E R F G H M D P N V C B M N S T V W Note 1: Cannot be combined with heater break alarm. ( 2, 3, 6, 7, H cannot be specified on 9th digit.) Note 2: In case of the combination 9th digit code: 3, 7, F, G, H, M or P and PXR4 the following installation condition are required. Note 3: Cannot be combined with RS point digital input. (V and W cannot be specified on 11th digit.) Note 4: In the case of control output 2, either of heater break alarm or remote input can be selected. (A, C, E and R on the 7th digit, and 2,3,6,7,H, D and P on the 9th digit cannot be specified.) Input signal, measurement range, and set value at the time of deliver are as follows. When thermocouple is specified: Thermocouple K, Measurement range; 4 C, Set value; C When resistance bulb is specified: Pt, Measurement range; 15 C, Set value; C When voltage/current is specified: Scaling; 1%, Set value; % For the cases other than the above, specify input signal and measurement range. Input signal of the thermocouple and the resistance bulb can be switched by key operation on the front panel. The actuating method of the control output has been set reverse for control output 1, and direct for control output 2 at the time of delivery. Note that reverse and direct actuation can be switched by key operation on the front panel. 4

5 PXR5/9 PXR Digit Specification Note 4 <Front dimensions> 48 X 96mm 96 X 96mm 5 <Input signal> Thermocouple C Thermocouple F Resistance bulb Pt1 3-wire type C Resistance bulb Pt1 3-wire type F 1 5V DC 4 2mA DC 6 <Control output 1> Relay contact output Voltage pulse output (24V DC) 4 2mA DC output Note 1 7 <Control output 2> None Relay contact output Voltage pulse output (24V DC) 4 2mA DC output Re-transmission output (4 2mA DC) 8 <Revision code> 9 <Optional specifications 1> None Alarm (1 pc.) Alarm for heater break Note 2 Alarm (1 pc.) + Alarm for heater break Note 2 Ramp-soak Alarm (1 pc.) + Ramp-soak Alarm for heater break + Ramp-soak Note 2 Alarm (1 pc.) + Alarm for heater break + Ramp-soak Note 2 Alarm (2 pcs.) Alarm (2 pcs.) + Ramp-soak Alarm (2 pcs.) + Alarm for heater break + Ramp-soak Note 2 Alarm (3 pcs.) Remote Note 2 Remote + Alarm (2 pcs.) Note 2 1 <Instruction manual> <Power supply voltage> None 1 24V AC English 1 24V AC None 24V DC English 24V DC 11 <Optional specifications 2> 12 None 13 RS485 (Modbus) communication RS485 (ASCII) communication Digital input 1 point Digital input 2 points Note 3 RS485 (Modbus) communication + Digital input 1 point RS485 (ASCII) communication + Digital input 1 point 5 9 T R N S A B A C E Y A C E R F G H M D P N V C B M N S T V W Note 1: Cannot be combined with heater break alarm. ( 2, 3, 6, 7, H cannot be specified on 9th digit.) Note 2: Cannot be combined with RS point digital input. (V and W cannot be specified on 11th digit.) Note 3: In the case of control output 2, either of heater break alarm or remote input can be selected. (A, C, E and R on the 7th digit, and 2,3,6,7,H, D and P on the 9th digit cannot be specified.) Input signal, measurement range, and set value at the time of deliver are as follows. When thermocouple is specified: Thermocouple K, Measurement range; 4 C, Set value; C When resistance bulb is specified: Pt, Measurement range; 15 C, Set value; C When voltage/current is specified: Scaling; 1%, Set value; % For the cases other than the above, specify input signal and measurement range. Input signal of the thermocouple and the resistance bulb can be switched by key operation on the front panel. The actuating method of the control output has been set reverse for control output 1, and direct for control output 2 at the time of delivery. Note that reverse and direct actuation can be switched by key operation on the front panel. 5

6 1 Part Names and Functions This chapter explains the part names and functions on the face panel. The face panel has the and displays, the status indicating lamp, and the setting keys, etc. Those functions are explained below. Please read and understand them before using the PXR. For details about the setting of parameters, see Chapter w Lamp for control output 2 q Lamp for control output 1 e Alarm lamp C1 C2 AL1 AL2 AL3 C r (Measured value) display i lamp PXR SEL t (Setting value) display o Au-tuning/self-tuning/manual mode lamp y SEL key u keys q Lamp for control output 1 Lights up while control output 1 stays ON. w Lamp for control output 2 Lights up while control output 2 stays ON. e Alarm lamp Lights up on detecting an alarm. The alarm output is turned ON at the same time. If the optional heater break alarm is provided, the AL3 lamp lights up on detecting a heater break. r (Measured value) display s the. When setting a parameter, its name appears. t (Setting value) display s the. When setting a parameter, its value appears. y SEL key Used select a parameter block and a parameter, and register a set value. u keys Used change the, call parameters, and change parameter values. i lamp Lights up while the is displayed in the display. When parameters and data are displayed, the lamp goes out. o Au-tuning/self-tuning/manual mode lamp Flashes under an au-tuning or self-tuning operation. The lamp is kept on in manual mode. 6

7 2 Operations This chapter explains how set the (Setting value) and the parameters for the PXR. 2-1 Parameter list Parameters for the PXR are classified in operation parameters, and the first block, the second block and the third block parameters according the frequency of use. The second and the third block parameters are used at initialization or when they are absolutely necessary. Operation parameter Parameter display symbol () () Parameter display symbol Parameter name Measured temperature (Measurement value) Set temperature (Set value) Parameters of the first block Parameter name Manual mode selection Standby setting Remote/local setting Ramp-soak control Alarm latch cancel Set value of alarm 1 Lower limit value of alarm 1 Upper limit value of alarm 1 Set value of alarm 2 Lower limit value of alarm 2 Upper limit value of alarm 2 Set value of alarm 3 Lower limit value of alarm 3 Upper limit value of alarm 3 Description Switches between Au and Manual operation modes. Cancels the alarm latch. Timer 1 display s the remaining time of timer Timer 2 display s the remaining time of timer Timer 3 display s the remaining time of timer Sets the value at which alarm 1 is detected. Sets the lower limit value at which alarm 1 is detected. Sets the upper limit value at which alarm 1 is detected. Sets the value during which alarm 2 is detected. Sets the lower limit value at which alarm 2 is detected. Sets the upper limit value at which alarm 2 is detected. Sets the value at which alarm 3 is detected. Sets the lower limit value at which alarm 3 is detected. Sets the upper limit value at which alarm 3 is detected. Description s the currently measured temperature (Measurement value). Switches between RUN and Standby for control. Switches between remote and local operations. Au-tuning Used for setting the constants for,, and by au-tuning. is displayed when alarm type 1 is 15, or 32 34, and or is displayed when alarm type 1 is 16 3 is displayed when alarm type 2 is 15 or 32 34, and or is displayed when alarm type 2 is 16 3 is displayed when alarm type 3 is 15 or 32 34, and or is displayed when alarm type 3 is 16 3 Specifies whether or not allow the change of parameters. Setting range and Parameter facry default setting (*) mask DSP Setting not allowed. Setting range and facry default setting (*) on: Manual mode off: Au mode* on: Control standby (Output: OFF, Alarm: OFF) off: Control RUN* rem: Remote LoCL: Local off: Sp* run: Start HLd: Hold : Keeps the alarm latch.* 1: Opens up the alarm latch. : OFF (Resets the au-tuning or does not use it.)* 1: ON (Performs the au-tuning in the standard type.) 2: ON (Performs the au-tuning in low type ( value-1%fs).) - (Unit: seconds) - (Unit: seconds) - (Unit: seconds) When the alarm type is absolute value: 1%FS (*:1) When the alarm type is deviation: -1 1%FS (*:1) When the alarm type is absolute value: 1%FS (*:1) When the alarm type is deviation: -1 1%FS (*:1) When the alarm type is absolute value: 1%FS (*:1) When the alarm type is deviation: -1 1%FS (*:1) dp13-64 s the set temperature (Set value). 1%FS (*: %FS) Mask not allowed. : All settings are changeable both from the face panel and via communication.* 1: All settings are unchangeable from the face panel, but changeable via communication. 2: Only the is changeable from the face panel, and all settings are changeable via communication. 3: All settings are changeable from the face panel, but unchangeable via communication. 4: All settings are unchangeable from the face panel or via communication. 5: Only the is changeable from the face panel, but all settings are unchangeable via communication. User s set value Note: The parameters for which * is marked with the page number in Reference page are related Remedies of 4 on page 79. Reference page See page 78 for the method of turning on/off. 14 Parameter mask DSP dp13-32 dsp1-1 dp13-8 dsp1-2 dsp1-4 dsp1-8 dsp1-16 dsp1-32 dsp1-64 dsp1-128 dsp2-1 dsp2-2 dsp2-4 dsp2-8 dsp2-16 dsp2-32 dsp2-64 dsp2-128 dsp3-1 Reference page * 22 * 22 * 22 * 22 * 22 * 22 * 22 * 22 * 23 7

8 Parameters of the second block Note: The parameters for which * is marked with the page number in Reference page are related Remedies of 4 on page 79. Parameter display symbol Parameter name Proportional band Integral time Derivative time Hysteresis range for ON/OFF control Description Setting range and facry default setting (*) User s set value Parameter mask DSP Reference page Set. select the ON/OFF % (*: ) control (Two-position control). 32 seconds (*: 24) seconds (*: ) Sets the hysteresis for ON/OFF 5%FS (*: equivalent of C) control. dsp3-2 dsp3-4 dsp3-8 dsp * 27 Cooling-side proportional band coefficient. (*: ) dsp Cooling-side proportional band shift - + (*:.) dsp Output convergence value -1 1% (*: single., dual ) dsp Anti-reset windup 1%FS (*: 1%FS) dsp4-1 3 * Control algorithm Selects the control algorithm. PID: Runs normal PID control.* FUZY: Runs PID control with fuzzy logic. SELF: Runs PID control with self-running. dsp (Measured value) stable range Sets the stable range for the selftuning operation. 1%FS (*: 2%FS) dsp * Setting HYS (Hysteresis) mode Selects the hysteresis operation at ON/OFF control. off: Starts the two-position control at the values of +HYS/2 and -HYS/ on: Starts the two-position control at the values of and +HYS, or and -HYS.* dsp Cycle time of control output 1 Not shown at 4-2mA DC output RLY, SSR: 1 15 seconds (*: Contact output = 3, SSR/SSC-driven output = 2) dsp Cycle time of control output 2 (cooling-side) 1 15 seconds (*: 3) dsp Input signal code Set this parameter when changing the types of temperature sensors (*: specified by cusmer while ordering) Note 1 dsp Lower limit of measuring range (*: specified by cusmer while ordering) Note 1 dsp Upper limit of measuring range (*: specified by cusmer while ordering) Note 1 dsp5-1 4 Setting the decimal point position 2 (*: specified by cusmer while ordering) Note 1 dsp C / F selection (Measured value) offset (Setting value) offset Time constant of input filter C / F -1 1%FS (*: ) -5 5%FS (*: ). 9. seconds (*: ) dsp5-4 dsp5-8 dsp5-16 dsp * * Alarm type 1 Alarm type 2 Alarm type 3 Sets the types of alarm operations. Sets the types of alarm operations. Sets the types of alarm operations. 34 (*: /5) 34 (*: /9) 34 (*: ) dsp5-64 dsp5-128 dsp Status display of ramp-soak - (*: OFF) dsp6-2 5 Selecting rampsoak execute type Selects ramp-soak patterns. 1: Performs 1st 4th segments.* 2: Performs 5th 8th segments. 3: Performs 1st 8th segments. dsp st target value /Switching- value Sets the 1st target of ramp-soak operation. / Selected at switching- function for DI1 Within the limit. (*: %FS) dsp6-8 5 * First ramp segment time Sets the first ramp segment time. 99h59m (*:.) dsp

9 Note: The parameters for which * is marked with the page number in Reference page are related Remedies of 4 on page 79. Parameter display symbol Parameter name Description Setting range and facry default setting (*) User s set value Parameter mask DSP Reference page 1st soak segment time Sets the 1st soak segment time. 99h59m (*:.) dsp nd target Sets the 2nd target of ramp-soak operation. Within the limit. (*: %FS) dsp6-64 * 5 2nd ramp segment time Sets the 2nd ramp segment time. 99h59m (*:.) dsp nd soak segment time Sets the 2nd soak segment time. 99h59m (*:.) dsp rd target Sets the 3rd target of ramp-soak operation. Within the limit. (*: %FS) dsp7-2 * 5 3rd ramp segment time Sets the 3rd ramp segment time. 99h59m (*:.) dsp rd soak segment time Sets the 3rd soak segment time. 99h59m (*:.) dsp th target Sets the 4th target of ramp-soak operation. Within the limit. (*: %FS) dsp7-16 * 5 4th ramp segment time Sets the 4th ramp segment time. 99h59m (*:.) dsp th soak segment time Sets the 4th soak segment time. 99h59m (*:.) dsp th target Sets the 5th target of ramp-soak operation. Within the limit. (*: %FS) dsp7-128 * 5 5th ramp segment time Sets the 5th ramp segment time. 99h59m (*:.) dsp th soak segment time Sets the 5th soak segment time. 99h59m (*:.) dsp th target Sets the 6th target of ramp-soak operation. Within the limit. (*: %FS) dsp8-4 * 5 6th ramp segment time Sets the 6th ramp segment time. 99h59m (*:.) dsp th soak segment time Sets the 6th soak segment time. 99h59m (*:.) dsp th target Sets the 7th target of ramp-soak operation. Within the limit. (*: %FS) dsp8-32 * 5 7th ramp segment time Sets the 7th ramp segment time. 99h59m (*:.) dsp th soak segment time Sets the 7th soak segment time. 99h59m (*:.) dsp th target Sets the 8th target of ramp-soak operation. Within the limit. (*: %FS) dsp9-1 * 5 8th ramp segment time Sets the 8th ramp segment time. 99h59m (*:.) dsp th soak segment time Sets the 8th soak segment time. 99h59m (*:.) dsp9-4 5 Ramp-soak mode Selects the power-on start, repeat, and standby functions for ramp-soak operations. 15 (*: ) dsp9-8 5 Note 1: When a cusmer does not specify the settings while ordering, the following settings are selected as facry defaults. Thermocouple input: Thermocouple K Measured range: 4 C Resistance bulb input: Measured range: 15 C Voltage/Current input: Scaling: 1% 9

10 Parameters of the third block Note: The parameters for which * is marked with the page number in Reference page are related Remedies of 4 on page 79 Parameter display symbol Parameter name Description Setting range and facry default setting (*) User s set value Parameter mask DSP Reference page Control action Specifies control action and output at the input burn-out. 19 (*: specified by cusmer while ordering) Note 2 dsp (Setting value) lower limiter Sets the lower limit of the. 1%FS (*: %FS) dsp9-32 * 54 (Setting value) upper limiter Sets the upper limit of the. 1%FS (*: 1%FS) dsp9-64 * 54 Delay time 1 Delay time 2 Delay time 3 Current transe display HB (Set value of heater break alarm) setting Alarm 1 hysteresis Delay time or timer value for alarm 1 relay seconds (*: ) Delay time or timer value for alarm 2 relay seconds (*: ) Delay time or timer value for alarm 3 relay seconds (*: ) s the current detecr input value for HB alarm. - Sets the operation value that detects the heater break. Sets the hysteresis range of ON and OFF of alarm A (Setting.A turns off the HB alarm.) (*:.) 5%FS (*: 1) dsp9-128 dp1-1 dp1-2 dp1-4 dp1-8 dp * 59 Alarm 2 hysteresis Sets the hysteresis range of ON and OFF of alarm 5%FS (*: 1) dp1-32 * 59 Alarm 3 hysteresis Sets the hysteresis range of ON and OFF of alarm 5%FS (*: 1) dp * Alarm 1 options Sets the optional functions of alarms 1, 2 and 111 (*: ) dp Alarm 2 options Alarm 3 options Alarm latch (1: use, : not use) Alarm of error status (1: use, : not use) De-energized output (1: use, : not use) 111 (*: ) 111 (*: ) dp11-1 dp Lower limit for output 1 Sets the lower limit for output - 1% (*: -) dp Upper limit for output 1 Sets the upper limit for output - 1% (*: 1) dp Lower limit for output 2 Sets the lower limit for output - 1% (*: -) dp Upper limit for output 2 Sets the upper limit for output - 1% (*: 1) dp Output limit types Sets the limit types of outputs 1 and 2 (breaking the limit, or maintained within the limit). 15 (*: ) dp Output value (MV) display s the value of output - dp Output value (MV) display s the value of output - dp RCJ (Cold junction compensation) setting Sets the cold junction compensation function ON/OFF. ON: Performs the RCJ (Cold junction compensation).* OFF: Does not perform the RCJ (Cold junction compensation). dp gradient.1 (*: ) dp12-4 User-definable zero adjustment Shifts the zero point of input value. -5 5%FS (*: ) dp12-8 * 66 User-definable span adjustment Shifts the span of input value. -5 5%FS (*: ) dp12-16 * 66 DI1 (Digital input 1) operation Sets the DI1 operations. 12 (*: =OFF) dp DI2 (Digital input 2) operation Sets the DI2 operations. 12 (*: =OFF) dp Station No. Sets the station No. for communication. 255 (Setting does not start the communications function.) (*: 1) dp Parity setting Sets the parity for communication. (The baud rate is fixed at 96bps. : Odd parity* 1: Even parity 2: No parity dp Note 2: The following settings are selected as facry defaults depending on the model you order. Seventh digit = Y model: Seventh digit = A model: 4 1

11 Note: The parameters for which * is marked with the page number in Reference page are related Remedies of 4 on page 79. Parameter display symbol Parameter name Description Setting range and facry default setting (*) User s set value Parameter mask DSP Reference page Communication procol setting Switches communication procols between Modbus and ASCII : Z-ASCII 1 : Modbus (RTU) dp Re-transmission output type setting Sets the type of signals be outputted from re-transmission output. Setting range : / 1 : / 2 : MV/ 3 : DV (* : ) dp Re-transmission output scaling base side setting Re-transmission output scaling setting on the base side Setting range - % (*:.) dp Re-transmission output scaling span side setting Re-transmission output scaling on the span side Setting range - % (*: ) dp Remote input zero adjustment Shifts the zero point of input value. -5 5%FS (*: ) dp Remote input span adjustment Shifts the span point of input value. -5 5%FS (*: ) dp Remote input filter constant Sets the filter constant of remote input value.. 9. seconds (*:.) dp Remote input value display s remote input value. - dp Parameter mask Sets whether or not display each parameter. 255 (*: specified by cusmer while ordering) 78 11

12 2-2 Basic operations Just after power-on: The display below appears just after power-on. C1 C2 AL1 AL2 AL3 C C1 C2 AL1 AL2 AL3 C PXR SEL Status at delivery <In Au mode> PXR SEL <In Manual mode> How switch parameters: The figure below shows the basic operations for the PXR. Just after power-on (/ displayed) Setting parameters C C1 C2 AL1 AL2 AL3 Changes. Not operated for 3 seconds. SEL PXR SEL SEL SEL (approx. (approx. (approx. 1 second) 3 seconds) 5 seconds) SEL SEL Parameters of the first block Parameters of the second block Parameters of the third block Pressing and holding the keys makes the value increase or decrease fast. Basic operations for the PXR (In Au mode) 12

13 Just after power-on (/MV displayed) (/ displayed) Setting parameters Not operated for 3 seconds. C1 C2 AL1 AL2 AL3 C SEL C C1 C2 AL1 AL2 AL3 Changes MV. PXR SEL SEL PXR SEL Changes. SEL SEL SEL (approx. (approx. (approx. 1 second) 3 seconds) 5 seconds) SEL SEL Parameters of the first block Parameters of the second block Basic operations for the PXR (In Manual mode) Parameters of the third block Pressing and holding the keys makes the value increase or decrease fast. How set values: key: One press increases the value by Press and hold this key increase the value fast. key: One press decreases the value by Press and hold this key decrease the value fast. How register the set data: By pressing the SEL key, the displayed values are registered. Note that the () will be registered in 3 seconds without any operation. 13

14 2-3 Parameter functions and method of settings Method of setting the (Setting value) The is a target value for control. Any that is outside of the range set in the parameters of (lower limit) and (upper limit) of the third block cannot be set. (See page 5) Related parameters: (page 54) (page 54) [Setting example] Changing the from 25 C 1195 C Press the or keys display. will be registered in the () in three seconds. After that, the controller will operate with the being

15 Manual mode setting (Settings: off/on) This parameter switches the control mode between Au and Manual. During Manual operation, the decimal point is kept on at the far right in the display section. During Manual operation, au tuning or self tuning is not done. If the mode is switched Manual while au or self tuning is being done, the tuning is forcibly terminated. The PID parameter remains the same in such cases. Manual operation output is not limited by MV limit. Manual operation can be carried out during standby operation. The operation output set value during Au/Manual operation mode and manual mode is sred in non-volatile memory. It is kept sred even if a power interruption occurs. When the power is turned on again, the state before the power interruption is resumed. The following table lists the operation output at the time of switching between Au and Manual.. Au Manual Manual Au Balanceless bumpless MV output according (Switches manual mode, PID operation holding the MV value just (Sudden change may occur before the switching.) the MV value.) Manual MV Manual Single output Manual PID calculation AUTO MAnU = ON P-n1 = Single Dual output MV1 MV2 Au Au Limit Limit Standby Standby Error output Error output OUT1 OUT2 Manual [Setting example] Switching manual mode Press and hold the SEL key for one second, and is displayed. Press the SEL key once, and the current set value ( ) on the display section starts flickering. Press the or the keys display. Press the SEL key once, and the manual lamp at the lower right corner comes on, indicating that the mode has been switched Manual. To display operation status, press and hold the SEL key for two seconds. 15

16 Standby setting (Settings: off/on) This parameter switches the control between RUN and Standby. During standby, the control output and the alarm output stay OFF, like the standby for ramp-soak operation. While the alarm with a hold is selected, the hold function takes effect after changing the Standby setting from ON OFF. is displayed during the standby for ramp-soak operations or the controller changes the standby state in case of the occurrence of errors. The other operations are the same as those of the rampsoak standby. The setting of ON/OFF for standby is saved after poweroff. When the standby is set ON during the au-tuning, self-tuning, and ramp-soak operations, those operations will sp. (The PID constant will not be renewed.) Even through it is set OFF later, the au-tuning, self-tuning, and ramp-soak operations will not be re-started. During standby, the ON-delay timer is reset. When returning RUN from the standby state, the timer will start from the beginning. [Setting example] Starting the control Press and hold the SEL key for one second. will be displayed. Then press the key once. The current setting ( ) flashes on the display. Press the or keys display. The standby state for control is selected. (control output and all the alarm outputs: OFF) If you want display the operation status, press and hold the SEL key for two seconds. The value on the display will flash, indicating the standby status. 16

17 Local/remote operation setting (Setting range: LoCL/rEM) (Option) This parameter is used switch between local and remote operations. Set value Operation Performs local operation. Performs remote operation. ( and the set value () are displayed alternately in the display section on the front face while in remote operation.) Related parameters: (page 75) (page 75) (page 76) (page 77) * Local operation: Control by set by the keys on the front face, ramp-soak operation, selection determined by digital input, and setting via communication * Remote operation: Control by determined by Remote input [Setting example] Switching remote operation Press and hold the SEL key for one second. will be displayed on the display section. Press the keys display. The current setting ( ) in the display section flickers. Press the keys display. Flickering sps and the operation is switched remote. To display the operation status, press and hold the SEL key for two seconds. 17

18 Ramp-soak control (Settings: off/run/hld) (Option) This function aumatically changes the (Setting value) according the program pattern set in advance as shown in the right line graph. Up eight pairs of rampsoak operation can be programmed. The first ramp starts at the (Measured value) that is the one just before running the program. The program can also aumatically run at power-on (Power-on starting function). Refer the parameter of (page 47). Related parameters: (page 5) (page 5) (page 5) (page 5) (page 5) (page 49) Up First ramp TM1r First soak Second ramp Second soak Third ramp Ramp: the section in which the changes ward the target value. Soak: the section in which the is the target value, and remains unchanged. Third soak TM1S TM2S TM3S TM2r TM3r Fourth ramp TM4r Fourth soak TM4S Up TM8s Up TM8r [Setting example] Starting the ramp-soak operation Press and hold the SEL key for one second. will be displayed on the display. Press the key display The current setting ( ) flashes on the display. Press the or keys display. Then, the program will start according the ramp-soak pattern that is set in advance. If you want display the operation status, press and hold the SEL key for two seconds. 18

19 Canceling the alarm latch (Setting range: /1) (Option) This parameter cancels the alarm latch when it is latching. Related parameters: (page 6) [Setting example] Opening up the alarm latch Press and hold the SEL key for one second. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will change in a few seconds. If you want display the operation status, press and hold the SEL key for two seconds. 19

20 Au-tuning function (Settings: /1/2) [Note] If the controller is powered off during au-tuning, this makes the au-tuning ineffective with each parameter of,, and unchanged. To start the au-tuning operation, set 1 or 2 again. To suspend the au-tuning, set. This makes the au-tuning cancel with each parameter of,, and unchanged. Once the parameters of,, and are set aumatically by the au-tuning, those parameters are sred in the controller even after it is powered off. Therefore, it is not necessary execute the au-tuning again. By setting 1 or 2, the au-tuning operation starts, and at the end of the tuning, will be displayed aumatically. After the au-tuning operation, the controller starts operate at the aumatically set values of,, and. A decimal point at the right end of the display flashes during au-tuning. There are two codes for AT: Setting code [1]: standard type Performs the au-tuning based on the. Setting code [2]: Low type Performs the au-tuning based on the -1%FS. [Note] Since ON/OFF control is performed during au-tuning, overshoot against the may occur. To reduce the overshoot, execute the au-tuning operation with the setting code [2] (Low ) selected. The au-tuning can be executed both just after power-on and in a control or stable status. Related parameters: (page 24) (page 25) (page 26) (page 3) (page 28) [Setting example] Setting the au-tuning operation 1 Press and hold the SEL key for one second. will be displayed on the display. 7. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and the au-tuning will start. During au-tuning, a decimal point at the right end of the display flashes. When the au-tuning finishes properly, a decimal point sps flashing, and the set values of,, and parameters change. When the au-tuning finishes abnormally, a decimal point sps flashing, but the set values of,, and parameters remain unchanged. If you want display the operation status, press and hold the SEL key for two seconds. 2

21 ,, ing ON-delay alarm or the remaining time of timers (unit: seconds) (Option) These parameters display the remaining time of Timers display parameter 1, 2 and The remaining time of the ON/OFF-delay timer is counted down. When the counter shows, the alarm relay is closed. Remaining time (seconds) During count-down, if the changes the value of the temperature at which the alarm is set OFF, or if DI for the timer is set OFF, the counter is reset, and the alarm relay is opened. [Setting example] ing ON-delay alarm or the remaining time of timers Press and hold the SEL key for one second. will be displayed. Press the key display. The remaining time of timer 1 will be displayed. Press the or keys display the remaining time of, and. If you want display the operation status, press and hold the SEL key for two seconds. 21

22 Setting alarm 1, 2 and 3 Upper limit of alarm 1, 2 and 3 Lower limit of alarm 1,2 and 3 (Setting range: Absolute value alarm: 1%FS Deviation value alarm: -1 1%FS ) }(Option) These parameters are used for settings of alarm 1, 2 and When the alarm type (, or ) is set 15, alarms 1, 2 and 3 (, and ) can be set. When the alarm type (, or ) is set any value other than 15, the upper and lower limits of alarm 1, 2 and 3 (,,,,, ) can be set. [Note] Setting codes (12 15) cannot be selected in alarm type 1 and 3 ( / ). Related parameters:,, (page 46),, (page 59),, (page 55),, (page 6) [Setting example] Setting the operation value of alarm 2-1 C Press and hold the SEL key for one second. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will be registered for. After that, the controller will operate with the operation value of alarm 2 being -1 C. If you want display the operation status, press and hold the SEL key for two seconds. 22

23 Key lock (Setting range: 5) This parameter makes the set values of parameters unchangeable. However, the parameter name and the set values can be displayed. To reset the key lock, change. Even when the key lock is set, control and alarm functions can operate properly. There are six levels of the key lock: : Unlocked (reset) : All settings are unchangeable from the controller, but changeable via communication. : Only the is changeable from the controller, and all settings are changeable via communication. : All settings are changeable from the controller, but unchangeable via communication. : All settings are unchangeable from the controller or via communication. : Only the is changeable from the controller, but all settings are unchangeable via communication. [Setting example] Setting the key lock 2 Press and hold the SEL key for one second. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will be registered for. After that, any setting other than the cannot be changed from the front panel. If you want display the operation status, press and hold the SEL key for two seconds. 23

24 Proportional band (Setting range: % of the measured range) To select the ON/OFF control (two-position control), set.. It is not necessary set and. can be aumatically set by the au-tuning operation. When is o small, control will be unstable, and when is o large, the response will be delayed. Set the hysteresis of the ON/OFF control (two-position control) in the parameter. If au-tuning is run after the ON/OFF control is selected, the ON/OFF control changes the PID control. To keep the ON/OFF control selected, do not execute the autuning. [Setting example] Changing the proportional band from % 1% Press and hold the SEL key for three seconds. will be displayed on the display. The current setting ( ) flashes on the display. Press the or keys display. controller will operate with being 1%. will sp flashing and will be registered for. After that, the If you want display the operation status, press and hold the SEL key for two seconds. 24

25 Integral time (Setting range: 32 seconds) can be set aumatically by the au-tuning operation. can also be set manually. When is set, the integral operation does not start. When is set., this makes the setting of ineffective. [Setting example] Changing the integral time from 24 seconds 6 seconds Press and hold the SEL key for three seconds. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will be registered for. After that, the controller will operate with being seconds. If you want display the operation status, press and hold the SEL key for two seconds. 25

26 Derivative time (Setting range: seconds) can be set aumatically by the au-tuning operation. can also be set manually. When is set, the differential operation does not start. When is set., this makes the setting of ineffective. [Setting example] Changing the differential time from seconds seconds Press and hold the SEL key for three seconds. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will be registered for. After that, the controller will operate with being seconds. If you want display the operation status, press and hold the SEL key for two seconds. 26

27 Hysteresis range for ON/OFF control (Setting range: 5%FS) To select the ON/OFF control (two-position control), set.. It is not necessary set and. When the hysteresis range (Range of ON/OFF control) is o small, the output may switch the ON/OFF frequently. (This may affect the life of the device be controlled, especially when contact output is selected.) The unit of the set value of this parameter is C or F (engineering unit). The setting range varies according the measured range of input. [Ex] Input Thermocouple K : At measured range of 4 C, the setting range is 2 C. Resistance bulb : At measured range of 15 C, the setting range is 75 C. Related parameters: (page 24) (page 36) [Setting example] Changing the hysteresis range from 1 C 35 C Press and hold the SEL key for three seconds. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will be registered for. After that, the controller will operate with the hysteresis range being 35 C. If you want display the operation status, press and hold the SEL key for two seconds. 27

28 Cooling-side proportional band coefficient (Option: Available for DUAL output only) (Setting range:. ) This parameter is used for setting the cooling-side proportional band. (See the figure below.) Heating side Heating-side proportional band Output 5 Cooling-side proportional band Proportional band (P) Cooling side Coefficient:.5 Coefficient: Coefficient: MV Before setting the cooling-side proportional band, set the heating-side proportional band an optimum value. To select the two-position control for the cooling side, set.. Cooling-side Proportional band (P) = Coefficient proportional band 2 When is set. and is set. in the dual output type, the cooling output is as shown in the figure below. The hysteresis is fixed at.5%fs. Heating output (Output 1) Cooling output (Output 2) ON.5%.5% ON OFF OFF HYS DB Related parameters: (page 27) (page 24) (page 29) Ex) When making the proportional band of 1% of the full scale with the proportional band (P) being 5%: 5% 1% = Coefficient 2 Consequently, the coefficient is. [Setting example] Changing the cooling-side proportional band coefficient from 5 Press and hold the SEL key for three seconds. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will be registered for. After that, the controller will operate with the cooling-side proportional band coefficient being If you want display the operation status, press and hold the SEL key for two seconds. 28

29 Cooling-side proportional band shift (Dead band/overlap band) (Option: Available for DUAL output only) (Setting range: - +) This parameter is used for shifting the cooling-side proportional band from the set value. (See the figure below.) and when it is a negative value, the Overlap band. When is a positive value, it is called the Dead band, Since the unit of is same one used for MV [%], if you Output want set in the unit of deviation [%], must be Heating side Cooling side converted using the equation below. MV Overlap band Dead band MV 1 DB [%] = Deviation [%] P Ex) When making a dead band with a deviation of [%] from the while the proportional band (P) is %: 1 DB [%] = = 2 [%] MV=5% Consequently, set the parameter 2 [%]. Related parameters: (page 24) [Setting example] Shifting the cooling-side proportional band by Press and hold the SEL key for three seconds. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will be registered for. After that, the controller will operate with being %. If you want display the operation status, press and hold the SEL key for two seconds. 29

30 Output offset value (Setting range: - %) Anti-reset windup (Setting range: 1%FS) The anti-reset windup ( ) is aumatically set an optimum value by the au-tuning operation. By setting, the amount of overshoot can be adjusted. [Note] By making use of the fuzzy control system equipped with PXR, the amount of overshoot can be minimized without setting and. AR value AR value } } In this range, the integral operation is not performed. In this range, the integral operation is performed. } In this range, the integral operation is not performed. [Setting example] Changing the anti-reset windup from 6 C 8 C. Press and hold the SEL key for three seconds. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will be registered for. After that, the controller will operate with the anti-reset windup being 8 C. If you want display the operation status, press and hold the SEL key for two seconds. 3

31 Control algorithm (Settings: PID/FUZY/SELF) This parameter is used for selecting PID control, FUZZY- PID control, or PID control with self-tuning. To select the PID control or FUZZY-PID control, it is necessary set the parameters of,,, and manually or by the au-tuning in advance. For the ON/OFF control (Two-position control), select the PID control and then set.. For detailed information, refer (page 24). Refer the next page for the PID control with self-tuning. [Setting example] Changing the control system from PID FUZZY Press and hold the SEL key for three seconds. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will be registered for. After that, the controller will operate with the FUZZY control system activated. If you want display the operation status, press and hold the SEL key for two seconds. 31

32 [Self-tuning] 1 Function: With the self-tuning function, PID parameters are aumatically re-optimised depending on the actual condition of device be controlled and the setting temperature (). 2 How execute: Follow the procedure shown below set and execute the self-tuning. The self-tuning starts run at the appropriate conditions. (See page 31) q Power on the PXR. w Set the. e Select in the parameter of.* 1 r Power off the PXR. If the device that is be controlled has powered ON at this point: Wait until the temperature of the device that is be controlled falls and stabilizes. To re-start the self-tuning: Select in the parameter of. t Power on the device be controlled. y Power on the PXR. The device be controlled and the PXR should be powered ON at the same time or in order of the left flowchart. (Tuning / Control) * 2 *1: How set the parameter of : SEL SEL *2: during self-tuning is shown below: This lamp flashes. 32

33 3 Conditions under which the self-tuning runs: q At power-on: The self-tuning runs when all of the following conditions are met. The that appears at power-on is not the same one when the,,, and were set previously. (i.e. the,,, and set by the self-tuning, au-tuning, manual setting, and writing by communications ols at previous time) The (-) at power-on is larger than (the value of input range) or (the set value of ). w When the is changed: The self-tuning runs when all the conditions below are met. The changed is larger than the that was set when the,,, and were selected previously. The changed amount of the is larger than. The changed amount of the is larger than (the set value of input range) or (the set value of ). e When output becomes unstable: The self-tuning runs when control becomes unstable and the hunting of the operating output (MV) occurs. (The selftuning runs only once as long as the is not changed.) r When the control standby mode is cancelled: The self-tuning runs by the same reason as q At power-on are met. * Only when the PXR is set standby mode at power-on. 4 Conditions under which the self-tuning does not run: q During control standby mode w During two-position control (Parameter of = ) e During au-tuning operation r During ramp-soak operation t Error display ( or is displayed.) y During dual output (The set value of the parameter of is larger than ) u When setting the parameters of,,, and manually (including the setting written by communications ols) 5 Conditions under which the self-tuning is suspended: q At the condition described in 4 shown above w When the is changed during self-tuning operation e When the self-tuning operation can not be completed within approx. 9 hours 6 Caution q Once the PID constant is set, the self-tuning does not operate at next power-on as long as the is not changed. w For an accurate tuning, be sure power on the device be controlled before or at the same time as the PXR is powered on. If the PXR has be powered on first for reasons of the system configuration, perform the au-tuning with the PID or FUZZY control. e If the device be controlled is powered on under temperature change (especially when it rises), accurate tunings can not be performed. Be sure power on the PYX when the temperature of device be controlled is stabilized. r The self-tuning does not run for cooling system control under Direct Action output (Parameter = 2 or 3). t In case the control is not stable after performing the self-tuning, change the algorithm the PID or FUZZY control and perform the au-tuning. 33

34 7 Reference [About the self-tuning method] The PID constant is calculated in one of the following two methods. The method is selected aumatically depending on the characteristics of the device be controlled. Step response method Limit cycle method The following figures show the operations at power-on and changing the, and under unstable control. q Operations at power-on Step response method Limit cycle method During tuning Time During tuning Time w Operations at changing the Step response method Limit cycle method Changing the Changing the During tuning Time During tuning Time e Operation under unstable control Limit cycle method Unstable control During tuning Time 1% MV 34

35 (Measured value) stable range (Setting range: 1%FS) Self-tuning logic recognizes that control is stable if is staying within the ±. It is not necessary set this parameter under normal conditions. [Setting example] Changing the stable range from 2 3 Press and hold the SEL key for three seconds. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or keys display. will sp flashing and will be registered for. After that, the controller will operate with the range being If you want display the operation status, press and hold the SEL key for two seconds. 35

36 HYS (Hysteresis) mode at ON/OFF control (Settings: off/on) This parameter is used for selecting the hysteresis operation mode at ON/OFF control. onof : OFF onof : ON : Starts the ON/OFF control at the values of HYS HYS + and : Starts the ON/OFF control at the values of and +HYS, or and -HYS. Default setting: ON Reverse action Direct action HYS HYS HYS HYS [Setting example] Setting the hysteresis mode ON Press and hold the SEL key for three seconds. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the key display. will sp flashing and will be registered for. After that, the controller will operate with the hysteresis being as shown in the figure of ON above. If you want display the operation status, press and hold the SEL key for two seconds. 36

37 Cycle time of control output 1 (Setting range: 1 15 seconds) This parameter is applicable for the contact output and SSR-driving output. While input is within the proportional band, output changes between ON and OFF in cycles. These cycles are called cycle time. Output: ON Cycle time Cycle time Do not set this parameter "". For contact output: The higher the frequency of output is, the more precise the control becomes. However a high frequency of output may shorten the life of the contacts and the device be controlled. Be sure adjust the proportional cycles considering controllability and the life of the device and the contacts. Typical: 3 seconds For SSR-driving output: Use in short cycles if there is no problem with the device be controlled. Typical: 1 2 seconds [Setting example] Setting the cycle time from 3 seconds 2 seconds Press and hold the SEL key for three seconds. will be displayed on the display. Press the key display. The current setting ( ) flashes on the display. Press the or key display. will sp flashing and will be registered for. After that, the controller will operate with the cycle time being 2 seconds. If you want display the operation status, press and hold the SEL key for two seconds. 37

Input signal Maximum Range Accuracy. Thermocouple E -50 to 700 C (-58 to 1832 F) ±1 C

Input signal Maximum Range Accuracy. Thermocouple E -50 to 700 C (-58 to 1832 F) ±1 C F4 Process Controller Installation and Operation Guide SAFETY ALERTS The symbols below are used on the equipment and throughout this document to draw the user s attention to important operational and safety

More information

TLK 48 MICROPROCESSOR-BASED DIGITAL ELECTRONIC REGULATOR

TLK 48 MICROPROCESSOR-BASED DIGITAL ELECTRONIC REGULATOR TLK 48 MICROPROCESSOR-BASED DIGITAL ELECTRONIC REGULATOR TECHNICAL DATA CARATTERISTICHE MECCANICHE Housing Self-extinguishing plastic, UL 94 V0 Dimensions 48x48 mm DIN depth 98 mm Weight 225 g approx.

More information

HONEYWELL DC 1010 / 1020 1030 / 1040 DIGITAL CONTROLLER PRODUCT MANUAL 51-52-25-113 06/02

HONEYWELL DC 1010 / 1020 1030 / 1040 DIGITAL CONTROLLER PRODUCT MANUAL 51-52-25-113 06/02 HONEYWELL DC 1010 / 1020 1030 / 1040 DIGITAL CONTROLLER PRODUCT MANUAL 51-52-25-113 06/02 Before using this manual, please check to ensure the Model number, input type Range and output match your requirements.

More information

PID Microprocessor temperature controllers CTD43 - CTD46 - CTH46

PID Microprocessor temperature controllers CTD43 - CTD46 - CTH46 PID Microprocessor temperature controllers CTD43 - CTD46 - CTH46 Display 1. Red measurement display (or the set point for CTD 43 by pressing, indicated by a flashing decimal point). 2. Green display of

More information

Temperature Controller CD401/CD901/CD701/CD501/CD100/CD101 Instruction Manual

Temperature Controller CD401/CD901/CD701/CD501/CD100/CD101 Instruction Manual Ⅰ. Warn Warning of connection Temperature Controller CD401/CD901/CD701/CD501/CD100/CD101 Instruction Manual If the controller fails to operate or error occurs, the system will bring fault for it, please

More information

PX-series digital temperature controller Example of Applications and Parameter Functions

PX-series digital temperature controller Example of Applications and Parameter Functions PX-series digital temperature controller Example of Applications and Functions ECNO:1158a Introduction This document provides examples of applications and major functions of three types of digital controllers

More information

SYL-2372 PID TEMPERATURE CONTROLLER INSTRUCTION MANUAL Version 1.4 (May 2016)

SYL-2372 PID TEMPERATURE CONTROLLER INSTRUCTION MANUAL Version 1.4 (May 2016) AUBER INSTRUMENTS Instruction Manual SYL-7 PID TEMPERATURE CONTROLLER INSTRUCTION MANUAL Version 1.4 (May 16) Caution This controller is intended to control equipment under normal operating conditions.

More information

Dyeing Programmer DP - 01

Dyeing Programmer DP - 01 Dyeing Programmer DP - 01 Display and Controls. 1) Display: 16/2 alphanumeric display 2) Temperature range: 0 to 150 degree. 3) Resolution: 1 degree. 4) Accuracy: +/- 1 degree. 5) Temperature control setting:

More information

Auto-tune PID. Temperature Controller BRAINCHILD FEATURES

Auto-tune PID. Temperature Controller BRAINCHILD FEATURES Auto-tune PID Temperature Controller FEATURES Easy-to-use Fuzzy modified PID heat & cool control Fast A-D sampling rate (5 times/s) Universal input (PT100, thermocouple) with high accuracy 18-bit A-D Analog

More information

2. Terminal arrangement. Default (PV display) (SV display) Communication protocol selection Selects the Communication protocol. Modbus ASCII mode:

2. Terminal arrangement. Default (PV display) (SV display) Communication protocol selection Selects the Communication protocol. Modbus ASCII mode: COMMUNICATION INSTRUCTION MANUAL TEMPERATURE CONTROLLER KT4, KT8 and KT9 No.KTC1E6 2009.05 To prevent accidents arising from the misuse of this controller, please ensure the operator receives this manual.

More information

Delta Temperature Controller User Manual

Delta Temperature Controller User Manual Delta Temperature Controller User Manual Foreword The user manual details the process of using Delta DT series temperature controllers step by step for beginners to easily set up all kinds of parameters

More information

+ A + + - B V B - - + + + NO NC V COM - - - PV PV

+ A + + - B V B - - + + + NO NC V COM - - - PV PV + - A + B B - V + - NO NC COM + - + - V + - PV PV Ramp Soak 100 70 50 30 3 5 3 8 5 3 Minute Steam Heating Sensor Cooling Water PID Hotplate Specifications Input power supply AC 100 to 240V, 50/60Hz, DC

More information

User Manual Auto Tuning PID Temperature Controller

User Manual Auto Tuning PID Temperature Controller User Manual Auto Tuning PID Temperature Controller TUPC-T series (Applicable for accurate controls of Temperature) TEMPSEN DEVICES Plot No : 2&3, Balaji Nagar, 4 th Street, Mettukuppam, Thoraipakkam, Chennai-600097

More information

Operational Overview and Controls Guide

Operational Overview and Controls Guide DOCUMENT: ECSEQ2-1 EFFECTIVE: 02/14/07 SUPERSEDES: 02/26/03 Operational Overview and Controls Guide Standard Two or Three Pump Type VFD Booster Controls 6700 Best Friend Road. Norcross, GA 30071. (770)

More information

INITIAL SETTING MANUAL

INITIAL SETTING MANUAL REX - C100 REX - C400 REX - C410 REX - C700 REX - C900 INITIAL SETTING MANUAL RKC RKC INSTRUMENT INC. F.M FRANKLIN PTY LTD PH. (07) 3391 4865 This is a manual for the initial setting of the REX-C100, -C400,

More information

The E5CN provides communications or event input functionality when mounted with one of the following Option Boards.

The E5CN provides communications or event input functionality when mounted with one of the following Option Boards. Digital Temperature Controller Compact and Intelligent Temperature Controller Auto-tuning and self-tuning available. Can auto-tune even during execution of self-tuning Heating or heating/cooling control

More information

MODEL 4400 TEMPERATURE CONTROL. 10100 Royalton Rd. Cleveland, OH 44133 (440) 237-3200 (440) 237-1744 http://iseinc.com

MODEL 4400 TEMPERATURE CONTROL. 10100 Royalton Rd. Cleveland, OH 44133 (440) 237-3200 (440) 237-1744 http://iseinc.com MODEL 4400 TEMPERATURE CONTROL 10100 Royalton Rd. Cleveland, OH 44133 (440) 237-3200 (440) 237-1744 http://iseinc.com Model 4400 Ramp Dwell Control Short Form Instructions This document is provided for

More information

SYL-2342, SYL-2352 PID TEMPERATURE CONTROLLER INSTRUCTION MANUAL Version 4.6 RTD R 4

SYL-2342, SYL-2352 PID TEMPERATURE CONTROLLER INSTRUCTION MANUAL Version 4.6 RTD R 4 AUBE ISTUMETS Instruction Manual SY, SY PID TEMPEATUE COTOE ISTUCTIO MAUA Version.6 Caution This controller is intended to control equipment under normal operating conditions. If failure or malfunction

More information

Process controller Setpoint programmer 1/16 DIN - 48 x 48 mm gammadue series M5 line

Process controller Setpoint programmer 1/16 DIN - 48 x 48 mm gammadue series M5 line BT. 2.9 M/E Process controller programmer /6 DIN - 48 x 48 mm gammadue series M line Advanced features, customizable and process adaptable High speed data aquisition and signal management. Efficent information

More information

HVAC-32A. Operation Manual. Specifications. Digital Multistage Air Conditioning Controller with inbuilt Outside Air Economy function

HVAC-32A. Operation Manual. Specifications. Digital Multistage Air Conditioning Controller with inbuilt Outside Air Economy function Specifications Supply Voltage 240VAC @ 0.07Amps or 24VAC @ 0.380Amps Relays 240V @ 12A max (resistive) / Comp1,2,3, Aux Ht, Rv O/B) Fuses (Equipment) 15 Amps Maximum 3AG Control Range Minus 10 to 50C Control

More information

DIGITRONIK Digital Indicating Controller SDC10. User s Manual

DIGITRONIK Digital Indicating Controller SDC10. User s Manual No. CP-UM-7E DIGITRONIK Digital Indicating Controller SDC User s Manual Thank you for purchasing the DIGITRONIK Digital Indicating Controller SDC. This manual contains information for ensuring correct

More information

FLOW CALCULATOR INSTRUCTION MANUAL MESURES BAMOPHOX 759 26-06-2007 759 M1 02 E MES FLOW CALCULATOR 759-02/1

FLOW CALCULATOR INSTRUCTION MANUAL MESURES BAMOPHOX 759 26-06-2007 759 M1 02 E MES FLOW CALCULATOR 759-02/1 BAMOPHOX 759 E - M FLOW CALCULATOR INSTRUCTION MANUAL MESURES 22, Rue de la Voie des Bans - Z.I. de la Gare - 95100 ARGENTEUIL Tél : (33) 01 30 25 83 20 - Web : www.bamo.fr Fax : (33) 01 34 10 16 05 -

More information

Softstarters. Type PSTX Fieldbus communication, Built-in Modbus RTU. 1SFC132089M0201 April 2015 1SFC132089M0201 1

Softstarters. Type PSTX Fieldbus communication, Built-in Modbus RTU. 1SFC132089M0201 April 2015 1SFC132089M0201 1 Softstarters Type PSTX Fieldbus communication, Built-in Modbus RTU 1SFC132089M0201 April 2015 1SFC132089M0201 1 1 Modbus RTU The Modbus protocol is a fieldbus protocol that provides full control and status

More information

#1381-3, Juan-dong, Nam-gu, Incheon, Korea TEL:(82-32) 876-4697 FAX:(82-32) 876-4696 http://www.hynux.com E-mail: sdt@hyelec.co.kr

#1381-3, Juan-dong, Nam-gu, Incheon, Korea TEL:(82-32) 876-4697 FAX:(82-32) 876-4696 http://www.hynux.com E-mail: sdt@hyelec.co.kr #1381-3, Juan-dong, Nam-gu, Incheon, Korea TEL:(8-3) 876-4697 FAX:(8-3) 876-4696 http://www.hynux.com E-mail: sdt@hyelec.co.kr MA01E50110 Recorder & Temperature Controller RT9 INSTRUCTION MANUAL Thank

More information

NC-12 Modbus Application

NC-12 Modbus Application NC-12 Modbus Application NC-12 1 Table of Contents 1 Table of Contents... 2 2 Glossary... 3 SCADA...3 3 NC-12 Modbus in general... 3 4 Entire system... 4 4.1 PFC to PC connection alternatives...4 4.1.1

More information

SR1, SR3 Series Digital Controller Instruction Manual

SR1, SR3 Series Digital Controller Instruction Manual SR, SR Series Digital Controller Instruction Manual Please do not begin operating this product until you have read this instruction manual thoroughly and you understand its contents. Safety Rules For matters

More information

HITACHI INVERTER SJ/L100/300 SERIES PID CONTROL USERS GUIDE

HITACHI INVERTER SJ/L100/300 SERIES PID CONTROL USERS GUIDE HITACHI INVERTER SJ/L1/3 SERIES PID CONTROL USERS GUIDE After reading this manual, keep it for future reference Hitachi America, Ltd. HAL1PID CONTENTS 1. OVERVIEW 3 2. PID CONTROL ON SJ1/L1 INVERTERS 3

More information

GST301. (Single Protection Zone) Operation Manual

GST301. (Single Protection Zone) Operation Manual GST301 Gas Extinguishing Control Panel (Single Protection Zone) Operation Manual 2 of 19 CONTENTS 1 OVERVIEW... 4 2 TECHNICAL DATA... 4 3 STRUCTURES... 5 3.1 FRONT SURFACE DESCRIPTION... 5 3.1.1 Indicators...

More information

Electrical Safety Tester

Electrical Safety Tester Electrical Safety Tester GPT-9000 Series QUICK START GUIDE GW INSTEK PART NO. 82PT-99040MA1 ISO-9001 CERTIFIED MANUFACTURER This manual contains proprietary information, which is protected by copyright.

More information

Sigma Control PC INSIDE. 97 psi 187 F R on load

Sigma Control PC INSIDE. 97 psi 187 F R on load Sigma Control PC INSIDE 97 psi 187 F R on load Innovation Sigma Control with a PC inside At Kaeser, we pride ourselves on being the world s leading innovator in air system technology. Over twenty-five

More information

Series 427. 1/16 DIN Multi-Mode Bar Graph Display Timer TIMERS PRODUCT HIGHLIGHTS

Series 427. 1/16 DIN Multi-Mode Bar Graph Display Timer TIMERS PRODUCT HIGHLIGHTS Series 427 1/16 DIN Multi-Mode Bar Graph Display Timer PRODUCT HIGHLIGHTS Digital Setting with 0.1% Accuracy Unique LED Bargraph Indicates Time Cycle in 20% Increments 8 Field Selectable Modes of Operation

More information

Series 935A User s Manual

Series 935A User s Manual Series 935A User s Manual Temperature Controller with Countdown Timer TOTAL CUSTOMER SATISFACTION 3 Year Warranty Registered Company Winona, Minnesota USA U.S. English 1241 Bundy Boulevard, P.O. Box 5580,

More information

Programmer/Controller

Programmer/Controller Systems Plus START 7 8 9 envirotronics ALARM STOP 4 5 6 ALARM ACK Instrument Manual Systems Plus Programmer/Controller OFF HELP 1 2 0 3. ENTER ALARM RESET DEL Revision 6 9/12/97 Table of Contents 2 Menu

More information

SERVICE INSTRUCTION R410A. WALL MOUNTEDtype INVERTER SPLIT TYPE ROOM AIR CONDITIONER. Models Indoor unit Outdoor unit

SERVICE INSTRUCTION R410A. WALL MOUNTEDtype INVERTER SPLIT TYPE ROOM AIR CONDITIONER. Models Indoor unit Outdoor unit SERVICE INSTRUCTION SPLIT TYPE ROOM AIR CONDITIONER WALL MOUNTEDtype INVERTER Models Indoor unit Outdoor unit ASYG07LECA ASYG09LECA ASYG12LECA ASYG14LECA AOYG07LEC AOYG09LEC AOYG12LEC AOYG14LEC R410A CONTENTS

More information

HEAT HEAT COOL HEAT PUMP COOL

HEAT HEAT COOL HEAT PUMP COOL OWNER S MANUAL RESIDENTIAL THERMOSTAT P/N P374-1800 HEAT COOL HEAT PUMP Su AUTO 0I20: Pm 74 COOL HEAT 27 7-DAY MABLE DIGITAL THERMOSTAT 3 Configurable Outputs Accepts Optional Humidity Module: Control

More information

SECTION 5 Examples of Function Block Combinations

SECTION 5 Examples of Function Block Combinations SECTION 5 Examples of Function Block Combinations 5-1 BASIC EXAMPLES OF CONTROL... 152 5-1-1 Simple Control... 152 5-1-2 Multi-channel Control... 153 5-1-3 Control for Switching Multiple Set Points...

More information

Operating Manual for the Electronic Built-in Interval Timer. Micro II (Countdown Timer)

Operating Manual for the Electronic Built-in Interval Timer. Micro II (Countdown Timer) Operating Manual for the Electronic Built-in Interval Timer Micro II (Countdown Timer) Note: This document has been designed for our OEM customers. They can use it as supporting material when creating

More information

Automation System TROVIS 6400 TROVIS 6493 Compact Controller

Automation System TROVIS 6400 TROVIS 6493 Compact Controller Automation System TROVIS 6400 TROVIS 6493 Compact Controller For panel mounting (front frame 48 x 96 mm/1.89 x 3.78 inch) Application Digital controller to automate industrial and process plants for general

More information

Automation System TROVIS 5100 Ventilation Controller TROVIS 5177

Automation System TROVIS 5100 Ventilation Controller TROVIS 5177 Automation System TROVIS 5100 Ventilation Controller TROVIS 5177 ounting and Operating Instructions EB 5177 EN Electronics from SASON Firmware version 1.05 Edition September 2000 Contents 1 Scope of the

More information

01-3 0000-00 6810-20 AIR CONDITIONING SYSTEM 1. FFH SPECIFICATION AIR CONDITIONING SYSTEM RODIUS 2004.09

01-3 0000-00 6810-20 AIR CONDITIONING SYSTEM 1. FFH SPECIFICATION AIR CONDITIONING SYSTEM RODIUS 2004.09 0000-00 01-3 6810-20 1. FFH SPECIFICATION 01-4 0000-00 2. SYSTEM LAYOUT AND COMPONENTS 0000-00 01-5 01-6 0000-00 3. FFH GENERAL INFORMATION The system is to increase the coolant temperature quickly by

More information

Section 1 Required hardware + sample wiring

Section 1 Required hardware + sample wiring UDC 3200 Application Note This application note is intended to explain how to configure a controller and a PC to utilize the email functionality of the controller. Section 1: Required hardware and wiring.

More information

NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter

NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter Description: The NTE2053 is a CMOS 8 bit successive approximation Analog to Digital converter in a 20 Lead DIP type package which uses a differential

More information

DS1621 Digital Thermometer and Thermostat

DS1621 Digital Thermometer and Thermostat Digital Thermometer and Thermostat www.dalsemi.com FEATURES Temperature measurements require no external components Measures temperatures from 55 C to +125 C in 0.5 C increments. Fahrenheit equivalent

More information

Digital Indicating Controllers. Bulletin 05P01A01-01EN. www.utadvanced.com

Digital Indicating Controllers. Bulletin 05P01A01-01EN. www.utadvanced.com Full Control at Your FingerTips Digital Indicating Controllers Bulletin 05P01A01-01EN www.utadvanced.com INTRODUCING THE Balancing Simplicity and Power The UTAdvanced was designed as a result of knowledge

More information

DPI 260 SERIES: Digital Pressure Indicators

DPI 260 SERIES: Digital Pressure Indicators DPI 260 SERIES: Digital Pressure Indicators INTRODUCTION The DPI 260, 261 and 262 range of digital pressure instruments measure and indicate pressure in any specified scale units and provide accuracies

More information

sip Sanyo Modbus Guide Technical Specification Pinouts, Cable Connections & Wiring Issue 2: February 2009 Synapsys Solutions Ltd, all rights reserved

sip Sanyo Modbus Guide Technical Specification Pinouts, Cable Connections & Wiring Issue 2: February 2009 Synapsys Solutions Ltd, all rights reserved Sanyo Section : Section : Section : Section : Section : sip Modbus Guide Configuration Modbus Table Technical Specification Pinouts, Cable Connections & Wiring Alarm Fault Codes Issue : February 009 Section

More information

THYRISTORS T1-1PH from 850A to 2700A Specifications Universal 1 Phase Thyristor Unit 55-77-03-62, March 2012

THYRISTORS T1-1PH from 850A to 2700A Specifications Universal 1 Phase Thyristor Unit 55-77-03-62, March 2012 Technical Information THYRISTORS T1-1PH from 850A to 2700A Specifications Universal 1 Phase Thyristor Unit 55-77-03-62, March 2012 GENERAL DESCRIPTION THYRISTORS T1-1PH is a full digital and universal

More information

PIEZOMETER AIRFLOW MEASURING RING

PIEZOMETER AIRFLOW MEASURING RING PIEZOMETER AIRFLOW MEASURING RING M.K. Plastics is pleased to introduce The Piezometer Airflow Measuring Ring, now available as an accessory for our steel Axijet fans. The system consists of a Piezometer

More information

Introduction NOTE Exclusions

Introduction NOTE Exclusions INP-TN514450c-E Introduction Thank you for purchasing the Fuji Digital Temperature Controller. This document describes how to connect the Micro controller PXG Series (referred to below as "Micro controller")

More information

NOW A PRODUCT! 1 /4 DIN PROCESS CONTROLLER. Single Loop Profile Controller (optional) NEMA 4X Front Panel PowerTune. The Interface Solution Experts

NOW A PRODUCT! 1 /4 DIN PROCESS CONTROLLER. Single Loop Profile Controller (optional) NEMA 4X Front Panel PowerTune. The Interface Solution Experts NOW A 5 3 5 The Interface Solution Experts PRODUCT! 5 3 5 1 /4 DIN PROCESS CONTROLLER Single Loop Profile Controller (optional) NEMA 4X Front Panel PowerTune The Interface Solution Experts www.miinet.com

More information

Operating Instructions. Single Loop Controller EC48 & EC96

Operating Instructions. Single Loop Controller EC48 & EC96 Operating Instructions Single Loop Controller EC48 & EC96 03/2010 PSG Plastic Service GmbH 1 Operating Instructions EC48 & EC96 Table of Contents 1 Introduction... 3 1.1 Typographical Conventions... 4

More information

Process Control Primer

Process Control Primer Process Control Primer At the onset of the Industrial Revolution, processes were controlled manually. Men turned valves, pulled levers or changed switches based on the need to turn devices on or off. As

More information

Technical data. General specifications. Indicators/operating means. 30 Hz Multiplex operation 30 Hz / n, n = number of sensors, n 5

Technical data. General specifications. Indicators/operating means. 30 Hz Multiplex operation 30 Hz / n, n = number of sensors, n 5 Model Number Single head system Features Parameterization interface for the application-specific adjustment of the sensor setting via the service program ULTRA 000 programmable switch outputs Hysteresis

More information

OCS-S High Resolution Digital Crane Scale

OCS-S High Resolution Digital Crane Scale OCS-S High Resolution Digital Crane Scale Content 1. Safety Guide... 1 2. Features... 1 3. Specifications... 2 4. Capacity... 2 5. Dimension & Weight... 3 6. Display & Keys... 4 Scale Keys... 4 Indicators...

More information

Controller Automation, Model II+

Controller Automation, Model II+ Controller Automation Page 2 of 2 Automation with the RADAK II+ power controller II+ I/O Points: Inputs 5 Programmable Digital inputs 2 Dedicated digital inputs (Channel select and External SCR control

More information

Operating Manual. CAL 3300 and 9300 Autotune Temperature Controllers. CAL Controls. Temperature Controllers

Operating Manual. CAL 3300 and 9300 Autotune Temperature Controllers. CAL Controls. Temperature Controllers Operating Manual CAL 3300 and 9300 Autotune Temperature Controllers CAL Controls Temperature Controllers INDEX SAFETY & WARRANTY A1 FUNCTIONS MENU A3 QUICK START Quick Start Set-up 1a INTRODUCTION 2 The

More information

ABB i-bus EIB Logic Module LM/S 1.1

ABB i-bus EIB Logic Module LM/S 1.1 Product Manual ABB i-bus EIB Logic Module LM/S 1.1 Intelligent Installation System Contents page 1 General... 3 1.1 About this manual... 3 1.2 Product and functional overview... 3 2 Device technology...

More information

User Manual THR840DUK Digital Thermostat

User Manual THR840DUK Digital Thermostat User Manual THR840DUK Digital Thermostat 50051982-001 Rev. A WARNING: This product must be correctly installed and configured to work properly (see pages 12-24). If you are not experienced in wiring electrical

More information

Programmable Single-/Dual-/Triple- Tone Gong SAE 800

Programmable Single-/Dual-/Triple- Tone Gong SAE 800 Programmable Single-/Dual-/Triple- Tone Gong Preliminary Data SAE 800 Bipolar IC Features Supply voltage range 2.8 V to 18 V Few external components (no electrolytic capacitor) 1 tone, 2 tones, 3 tones

More information

4-Channel Thermometer / Datalogger

4-Channel Thermometer / Datalogger USER GUIDE 4-Channel Thermometer / Datalogger RTD and Thermocouple Inputs Model SDL200 Introduction Congratulations on your purchase of the Extech SDL200 Thermometer, an SD Logger Series meter. This meter

More information

MAGICAR M871A. Car alarm with two-way remote User s guide

MAGICAR M871A. Car alarm with two-way remote User s guide MAGICAR M871A Car alarm with two-way remote User s guide EN MAGICAR M871A Car alarm with two-way remote User s guide TABLE OF CONTENTS Table of contents...2 1. Important notice...4 2. Introduction...4

More information

MEMOBUS/Modbus Communications

MEMOBUS/Modbus Communications 2 2.1 MEMOBUS/MODBUS CONFIGURATION............260 2.2 COMMUNICATION SPECIFICATIONS..............261 2.3 COMMUNICATION TERMINAL RESISTANCE........262 2.4 CONNECTING A PLC...........................263 2.5

More information

Technical data. General specifications. Indicators/operating means. Electrical specifications Operating voltage U B Power consumption P 0 Interface

Technical data. General specifications. Indicators/operating means. Electrical specifications Operating voltage U B Power consumption P 0 Interface Release date: 06-0- 09: Date of issue: 06-0- 009_eng.xml Model Number Single head system Features Parameterization interface for the application-specific adjustment of the sensor setting via the service

More information

BACK PRESSURE MONITOR Operator Display with Exhaust Temperature KIT 194-722

BACK PRESSURE MONITOR Operator Display with Exhaust Temperature KIT 194-722 HEWITT INDUSTRIES 5492 BOLSA AVE. HUNTINGTON BEACH, CA 92649 PH. (714) 891-9300 FAX. (714) 897-7632 WEBSITE: www.hewittindustries.com E-MAIL: sales@hewittindustries.com BACK PRESSURE MONITOR Operator Display

More information

PSC-A5 Solar Charge Controller Manual

PSC-A5 Solar Charge Controller Manual ( 5A, 12V/24V Output, Double Mode ) 1. Introduction: This controller is suitable for 12V and 24V solar photovoltaic system. The charge and discharge current is 5A. The maximum solar panel for 12V system

More information

BODY ELECTRICAL TOYOTA ELECTRICAL WIRING DIAGRAM WORKBOOK. ASSIGNMENT Version 1.8 WORKSHEETS. http://www.autoshop101.com

BODY ELECTRICAL TOYOTA ELECTRICAL WIRING DIAGRAM WORKBOOK. ASSIGNMENT Version 1.8 WORKSHEETS. http://www.autoshop101.com BODY ELECTRICAL ASSIGNMENT Version 1.8 WORKSHEETS TOYOTA ELECTRICAL WIRING DIAGRAM WORKBOOK http://www.autoshop101.com Developed by Kevin R. Sullivan All Rights Reserved TOYOTA Table of Contents Wiring

More information

HYDRUS ULTRASONIC METER

HYDRUS ULTRASONIC METER HYDRUS APPLICATION HYDRUS is a static water meter based on the ultrasonic technology. This technology enables accurate calculation of water consumption and eliminates measuring deviations caused by sand,

More information

MLC 9000+ TM Maximum Productivity and Versatility for Control without Compromise!

MLC 9000+ TM Maximum Productivity and Versatility for Control without Compromise! Data Sheet Maximum Productivity and Versatility for Control without Compromise! Basic Bus Communication Module DESCRIPTION The Basic Bus Communication Module (BCM) is part of the MLC 9000+ DIN rail mount

More information

S4000TH HART. HART Communication Manual

S4000TH HART. HART Communication Manual HART Communication Manual The information and technical data disclosed in this document may be used and disseminated only for the purposes and to the extent specifically authorized in writing by General

More information

Configurator Software Manual

Configurator Software Manual Configurator Software Manual The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the right to alter specifications

More information

DSL INSTRUCTION MANUAL

DSL INSTRUCTION MANUAL DSL INSTRUCTION MANUAL 7010 Lindsay Dr., Mentor, OH 44060 Phone: 440-974-1300 U.S./Canada: 800-621-1998 FAX: 440-974-9561 Email: info@process-technology.com www.processtechnology.com Certified to ISO 9001:2008,

More information

Process modules Digital input PMI for 24 V DC inputs for 120 V AC inputs

Process modules Digital input PMI for 24 V DC inputs for 120 V AC inputs E031026 000823 Process modules Digital input PMI for inputs for 120 V AC inputs PMI Input E4, E5, GND L- PMI 120 V AC Input E4, E5, Common C E6, E7, GND L- E6, E7, Common C LEDs for the inputs operation

More information

Digital and Analog I/O

Digital and Analog I/O 70072-0127-07 TECHNICAL NOTE 02/2007 Digital and Analog I/O This document discusses the application and configuration of digital and analog inputs/outputs (I/O). Details are for both onboard I/O and external

More information

Druck DPI 104. GE Industrial Sensing. Digital pressure indicator User manual - K394

Druck DPI 104. GE Industrial Sensing. Digital pressure indicator User manual - K394 GE Industrial Sensing 99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com Druck DPI 104 Digital pressure indicator User manual - K394 A1.1 A1.2 B1 1 A2 B2 2 3 4 5 6 A1.3 8 7

More information

EXTERNAL DIMENSIONS AND PARTS

EXTERNAL DIMENSIONS AND PARTS FX2N-4DA SPECIAL FUNCTION BLOCK USER S GUIDE JY992D65901A This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX2N-4DA special

More information

Thyristor-controlled power supplies and battery chargers

Thyristor-controlled power supplies and battery chargers Thyristor-controlled power supplies and battery chargers Input voltage: 115 / 230 VAC, single phase, 50 / 60 Hz or 208 / 400 / 480 VAC, three phases, 50 / 60 Hz Output voltage: 12 / 24 / 48 / 60 / 72 /

More information

TAC I/NETTM MR-VAV-AX. Application Specific MicroRegulator TM

TAC I/NETTM MR-VAV-AX. Application Specific MicroRegulator TM TAC I/NETTM TM TAC s TM has an extensive range ofpre-engineered VAV control sequences, which combined with a fully integrated actuator and airflow transducer, makes it a low Total Installed Cost solution

More information

RF Etch Monitor. Introduction

RF Etch Monitor. Introduction RF Etch Monitor Introduction A newly designed RF Matching Controller & RF Etch Monitor replaces the old OEM design of the RF Matching Controller and the RF Etch Monitor. OEM RF Matching Controller: - Analog

More information

DC1000 Series General Purpose UNIVERSAL DIGITAL CONTROLLERS

DC1000 Series General Purpose UNIVERSAL DIGITAL CONTROLLERS DC1000 Series General Purpose UNIVESA DIGITA CONTOES PODUCT SPECIFICATION SHEET OVEVIEW The DC1000 family of microprocessor based controllers combine a high degree of functionality, reliability at a very

More information

TC-9102 Series Surface Mount Temperature Controllers

TC-9102 Series Surface Mount Temperature Controllers TC-9102 Series Surface Mount Temperature Controllers General Description & Applications The TC-9102 Series Temperature Controller offers a versatile solution for a wide variety of applications that may

More information

DC Electronic Loads 8500 series

DC Electronic Loads 8500 series Data Sheet DC Electronic Loads 8500 series 2400W 600 W - 1200 W 300 W Versatile & Economical DC Electronic Loads The 8500 series Programmable DC Electronic Loads can be used for testing and evaluating

More information

Transmitter Interface Program

Transmitter Interface Program Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following

More information

SIMATIC S7-1200. It s the Interplay that makes the difference. Siemens AG 2010. All Rights Reserved.

SIMATIC S7-1200. It s the Interplay that makes the difference. Siemens AG 2010. All Rights Reserved. SIMATIC S7-1200 It s the Interplay that makes the difference SIMATIC S7-1200 Controller SIMATIC S7-1200 CPUs CPU 1211C 3 configurations per CPU Dimensions W x H x D (mm) CPU 1212C CPU 1214C DC/DC/DC, AC/DC/RLY,

More information

GSM HOME SECURITY SYSTEM

GSM HOME SECURITY SYSTEM Cell /Mobile phone home security system GSM HOME SECURITY SYSTEM Model : GSM-120 TABLE OF CONTENTS 1. FEATURES... 1 2. APPLICATION... 2 3. SPECIFICATIONS... 3 4. FRONT PANEL & LAYOUT DESCRIPTION...6 5.

More information

User's Guide. Integrating Sound Level Datalogger. Model 407780. Introduction

User's Guide. Integrating Sound Level Datalogger. Model 407780. Introduction User's Guide 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Back to the Extech 407780 Product Page Integrating Sound Level Datalogger

More information

Inwall Room Temperature Unit

Inwall Room Temperature Unit Inwall Room Temperature Unit TM11B01KNX TM11B11KNX TM11B21KNX Product Handbook Product: Inwall Room Temperature Unit Order Code: TM11B01KNX TM11B11KNX TM11B21KNX Application Program ETS: TM11B_1KNX Inwall

More information

A Design of a PID Self-Tuning Controller Using LabVIEW

A Design of a PID Self-Tuning Controller Using LabVIEW Journal of Software Engineering and Applications, 2011, 4, 161-171 doi:10.4236/jsea.2011.43018 Published Online March 2011 (http://www.scirp.org/journal/jsea) 161 A Design of a PID Self-Tuning Controller

More information

SMS GSM Alarm Messenger

SMS GSM Alarm Messenger SMS GSM Alarm Messenger Data Logging Alarm Input Relay Output Voice Temperature Humidity Analog Input Capture and Send Data via SMS Report triggered alarm via SMS Output triggered via SMS Auto pick up

More information

9448 Installation and User Guide

9448 Installation and User Guide 9448 Installation and User Guide Compatible Equipment 9040 Internal Sounder 660 Speech communicator 496327 Issue 1 1 of 6 9448 INTRODUCTION The 9448 is a 3 zone control panel with separate Entry/Exit and

More information

Portal Software GSM-PRO Run LED displays module activity Com LED displays activity on the GSM network GSM-PRO

Portal Software GSM-PRO Run LED displays module activity Com LED displays activity on the GSM network GSM-PRO GSM-PRO GSM-PRO perfect for communication CONTA-CLIP s GSM-PRO module offers a remote control and maintenance solution which allows you to monitor and control decentralized facilities. The GSM-PRO module

More information

VOLTAGE/CURRENT CALIBRATOR ISO-TECH ILC-421

VOLTAGE/CURRENT CALIBRATOR ISO-TECH ILC-421 VOLTAGE/CURRENT CALIBRATOR ISO-TECH ILC-421 TABLE OF CONTENTS 1. FEATURES... 1 2. SPECIFICATIONS... 1 2-1 General Specifications...1 2-2 Electrical Specifications... 2 3. FRONT PANEL DESCRIPTION... 4 3-1

More information

B/S/H/ Error codes and service programmes PH

B/S/H/ Error codes and service programmes PH 1 ERROR CODES AND APPLIANCE MESSAGES... 3 1.1 Complete overview of all error codes (in order)... 3 Automatic switch-off... 3 Display is dark and any individual LEDs are lit... 3 E 005... 3 E 011... 3 E

More information

How To Set Up A Protocessor Protonode

How To Set Up A Protocessor Protonode Setup Manual BACnet Protocol Gateway for TempTrac and XR Water Heater Control When a BAS interface with TempTrac or the XR requires a protocol other than the standard Modbus RTU, PVI Industries offers

More information

Meter Relays. 077 Series Analogue Meter Relays. Features. Applications

Meter Relays. 077 Series Analogue Meter Relays. Features. Applications 077 Series Analogue Features Monitors and controls any variable which can be converted to an A.C. or D.C. signal. Rugged, shock and vibration resistant design Indicator, relays and power unit in one housing

More information

Sierra Dual 24 Volt Brushless DC Motor Controller Product Specification

Sierra Dual 24 Volt Brushless DC Motor Controller Product Specification Sierra Dual 24 Volt Brushless DC Motor Controller Product Specification Assembly 025A0215 600A0942 Rev. A May 14, 2012 025A0215 Brushless DC Motor Controller Page 1 Revision History ECN # Date Rev Description

More information

3BASIC RELAY INSTRUCTIONS

3BASIC RELAY INSTRUCTIONS M O D U L E T H R E E 3BASIC RELAY INSTRUCTIONS Key Points So far, you have learned about the components of the MicroLogix 1000 PLC, including the CPU, the memory system, the power supply, and the input/output

More information

BW-500 BED WEIGHER USER MANUAL

BW-500 BED WEIGHER USER MANUAL BW-500 BED WEIGHER USER MANUAL 0 1 TABLE OF CONTENTS SPECIFICATION... 3 Equipment... 4 INSTALLING WEIGH BEAM... 5 PREPARATION FOR MEASUREMENT... 6 DP3800 Indicator... 8 POWER SUPPLY... 8 PANEL... 9 KEY

More information

BROOKFIELD MODEL VTE250 ELECTRIC VISCOSEL PROCESS VISCOMETER. Installation, Operation, and Maintenance Instructions. Manual No.

BROOKFIELD MODEL VTE250 ELECTRIC VISCOSEL PROCESS VISCOMETER. Installation, Operation, and Maintenance Instructions. Manual No. BROOKFIELD MODEL VTE250 ELECTRIC VISCOSEL PROCESS VISCOMETER Installation, Operation, and Maintenance Instructions Manual No. M06-512 SPECIALISTS IN THE MEASUREMENT AND CONTROL OF VISCOSITY BROOKFIELD

More information

Operational Overview and Controls Guide. Two or Three Pump IronHeart Lite with Variable Frequency Drives

Operational Overview and Controls Guide. Two or Three Pump IronHeart Lite with Variable Frequency Drives DOCUMENT: ECSEQ6-0 EFFECTIVE: 09/23/10 SUPERSEDES: Operational Overview and Controls Guide Two or Three Pump IronHeart Lite with Variable Frequency Drives 6700 Best Friend Road. Norcross, GA 30071. (770)

More information

Owner s Manual. Walk-in Monitoring System 100. Cooler is Better! TM. Used in UL Listed Door Panel Assemblies

Owner s Manual. Walk-in Monitoring System 100. Cooler is Better! TM. Used in UL Listed Door Panel Assemblies REV. G Cooler is Better! TM Owner s Manual Walk-in Monitoring System 100 Used in UL Listed Door Panel Assemblies American Panel Corporation 5800 S.E. 78th Street, Ocala, Florida 34472-3412 Phone: (352)

More information