INSTALLATION INSTRUCTIONS Faucet and Basic In-line Models

Transcription

1 For RV and Marine Use Only No more tank taste! Purifies Instantly and Naturally, Without Adding Chemicals Compact, Convenient and Complete Installs in Minutes Reliable and Simple to Use Just Turn on the Water INSTALLATION INSTRUCTIONS Faucet and Basic In-line Models Not for Residential Use Better Than Bottled Water At a Fraction of the Cost

2 Your Nature Pure purification unit will be ready to use immediately after installation. The faucet is "top-mounting" and all connections, downstream of the connection to your cold water line, are made using our "Quick and Easy TM " installation lines. Please see the diagrams for each type of installation. cold water line Helpful Hint #1 Install mounting bracket by positioning on inside wall of sink cabinet in a location that allows easy access for cartridge replacement. Make sure inlet and outlet connection lines reach. RV/Marine IN-LINE MODEL INSTALLATION insert elbows, secure with customer supplied hose clamps inlet line outlet line cold water line to pure water center outlet mounting bracket RV/Marine IN-LINE MODEL INSTALLATION Installed cold water supply lines vary by manufacturer. If the supplied Nature Pure Tee does not fit your configuration, these should. Flair-It Tee Hepworth Hep 2 O Tee Swivel insert tee, secure with hose clamps pure water hose line from faucet to center outlet cold water line mounting bracket

3 RV/MARINE MOUNTING BRACKET INSTALLATION 1. Screw wall plate to wall with the 2 screws supplied with retainer latch up. retainer latch Note: Be sure to leave enough clearance when mounting wall plate for placing and removing unit with hoses attached. 2. Slide the ring bracket down onto the wall plate until it snaps into place as shown. cover retainer latch 3. Slide the nature pure into the ring bracket until the retainer latches over the cover. The taper lock fit will hold the unit securely. cover retainer latch 4. To remove the unit - Push the retainer latch away from cover - rotate and lift the unit from the bracket.

4 FAUCET INSTALLATION 1. Determine faucet location and cut a ¾" hole (fits up to a 1½" hole). (We've included a handy Faucet Mounting Template at the bottom of this column.) Be sure to check for proper clearance of faucet stem underneath sink. 4. Position faucet and hand tighten (only) split nut. 2. Place faucet stem through black base gasket and then securely hand tighten hose onto faucet stem. 3. Drop free end through mounting hole. 5. Insert and rotate patented threaded taper fit spout. Thread spout into base, Do not over tighten. Faucet Mounting Template Cut out and position on sink ledge before making hole. 1¾" ¾"

5 CARTRIDGE INSTALLATION & REPLACEMENT 1. Turn off cold water supply. 2. Open faucet (Faucet Model only). Remove closure rod. 4. Remove old cartridge and insert new one. * When replacing cartridge apply light coat of petroleum jelly on o-rings. 3. Pull unit apart. Helpful Hint #2 If you have difficulty separating the cover from the bowl, water pressure can help. Follow steps 1 & 2, but close the faucet. With a pan ready to catch water from the unit, slowly turn on the water supply to the unit. Once the unit begins to separate, turn off the water supply. 5. Reassemble unit. Replace closure rod. 6. Turn on cold water supply with faucet open. Run water through new cartridge for 2-3 minutes to remove loose particles. Special Note To change swing direction of the faucet handle, move the pin under the handle. close-up of moveable pin Stainless steel pin Pin adjustable to right or left side

6 USE AND CARE Your water purifier is manufactured in the USA from the finest materials available. If properly cared for, it will provide a lifetime of convenient, effective operation. To clean faucet and unit surfaces properly, use a small amount of nonabrasive liquid detergent and a soft wet cloth. Gently rub the soiled surface until the dirt is removed. Then rinse clean and wipe with a dry soft cloth to remove water drops to prevent spotting. Hard water may leave mineral deposits or "water spots" if not cleaned regularly. These deposits may resist cleaning with simple liquid detergents, but usually can be removed using a small amount of vinegar applied directly and rubbing with a soft cloth. Chrome coatings should not be cleaned with abrasive or pumice type cleansers. They may permanently scratch or otherwise damage the chrome coating. The Structured Matrix TM cartridge should be replaced when the water flow diminishes, or if tastes or odors are noticed or after 500 gallons. Cartridge life will vary with water quality, but averages about 500 gallons. For long term storage, remove cartridge from purifier and allow to air dry. Store in a clean dry area. Nature Pure housing has a 1 year limited manufacturer s warranty and a rated 3-year life expectancy. Please note this is a guideline only. Please check your housing for signs of wear and tear that may indicate the need for replacement. Refer to warranty card for specific terms and conditions. WINTERIZING INSTRUCTIONS Do not permit antifreeze to enter the Nature Pure pressure vessel, hoses, faucet or the Nature Pure cartridge. 1. Turn off water pressure pump. 2. Open faucet to relieve pressure. 3. Disconnect inlet line from tee or elbow. Cap the tee or elbow with a a" compression cap nut. (#10 on Nature Pure parts list.) Drain Nature Pure pressure vessel and hoses. 4. Remove and allow cartridge to air dry, then store in a dry environment away from fumes, solvents or chemicals. Note: Be sure to completely flush antifreeze from water system before reinstalling the Nature Pure System. See instructions that came with your purifier. To order a replacement cartridge call: EST M-F For technical information call:

7 NATURE PURE PARTS Check the contents of this package for the parts listed. Should any part be missing, contact the dealer who sold you your Nature Pure system, or call EST M-F or Cover 2. Closure Rod 3. Cartridge 4. Large O-ring Seal 5. Bowl 6. Elbows (In-line Model Only) 7. Plastic Tee (Faucet Model Only) 8. Faucet Spout - Threaded Spout (Faucet Model Only). 9. Faucet Body (Faucet Model Only) 10. a" Compression Cap Nut (see winterizing instructions) " Hoses 12. RV/MARINE Mounting Bracket with screws 13. Base gasket and split nut

8 GENERAL ECOLOGY, INC. 151 Sheree Blvd. Exton, PA U.S.A fax: European Office: General Ecology Europe Ltd. St. Andrews House, 26 Brighton Road Crawley RH10 6AA U.K. +44(0) fax: +44(0) OTHER GENERAL ECOLOGY PRODUCTS Seagull IV X-1F Water Purifier First Need Deluxe Portable Water Purifier Trav-L -Pure Portable Water Purifier Made in the USA EPA. EST. REG. NO PA-01 TM trademarks of General Ecology, Inc General Ecology, Inc. rev. B 11/