ML-200. HDMI to SDI Scaler Converter with Genlock function. User Manual. rev: Made in Taiwan

Transcription

1 ML-200 HDMI to SDI Scaer Converter with Genock function User Manua rev: Made in Taiwan

2 Safety and Notice The ML-200 HDMI to SDI Scaer Converter with Genock function has been tested for conformance to safety reguations and requirements, and has been certified for internationa use. However, ike a eectronic equipments, the ML-200 shoud be used with care. Pease read and foow the safety instructions to protect yoursef from possibe injury and to minimize the risk of damage to the unit. Foow a instructions and warnings marked on this unit. Do not attempt to service this unit yoursef, except where expained in this manua. Provide proper ventiation and air circuation and do not use near water. Keep objects that might damage the device and assure that the pacement of this unit is on a stabe surface. Use ony the power adapter and power cords and connection cabes designed for this unit. Do not use iquid or aeroso ceaners to cean this unit. Aways unpug the power to the device before ceaning. TABLE OF CONTENTS INTRODUCTION... 1 FEATURES... 1 PACKAGE CONTENTS... 1 SPECIFICATIONS... 2 CONNECTION DIAGRAM... 2 PANEL DESCRIPTIONS... 4 OPERATION APPROACH... 5 WARRANTY... 10

3 INTRODUCTION The ML-200 HDMI to SDI Scaer Converter with Genock function provide a professiona way to convert HDMI to 3G/HD/SD-SDI in rea time. The conversion between HDMI and SDI is pure digita and guarantees no ess transformation for both audio and video. Pus, with up to 8 channes audio support, 7.1 channe or 5.1 channe audio becomes avaiabe. The ML-200 provides ow jitter SDI output and aso support genock. FEATURES Remote contro via Mini-USB Genock supported Input maximum pixe rate: HDMI-225MHz, VGA-165MHz Output bandwidth 2.97Gbps Supports mutipe VESA resoution Deinteracer supported Supports noise reduction and video enhancement features Over/under scanning adjustabe Video H/V mirror supported Active video area adjustment supported USB firmware upgraded for expanding compatibiity Wa-mount housing design for easy instaation PACKAGE CONTENTS 1x ML-200 1x User Manua 1x 5V 4A power suppy 1x UL power cord 1x Instaation software CD 1

4 SPECIFICATIONS Mode Name ML-200 Technica Roe of usage SDI standards Input Video Rate Output Video bandwidth Output Video support Audio support ESD protection HDMI & VGA to SDI Converter SD-SDI, HD-SDI & 3G-SDI [VGA] 165MHz [HDMI] 225MHz 2.970Gpbs, 2.970/1.001Gbps [3G eve A & B] (4:2:2) [HD] [SD] PCM 8 (48KHz Fs sampe rate) Human body mode ±15kV [air-gap discharge] & ±8kV [contact discharge] PCB stack-up 4-ayer board [impedance contro differentia 100Ω; singe 50Ω] Input Output Contro BNC connector HDMI connector USB connector 1x HDMI + 1x VGA+ 1x BNC 3x BNC + 2x XLR+ 1x DB25+ 1x HDMI Front Pane / USB 3G 75Ω inter-ocked socket Type A [19-pin femae] Type B Mechanica Encosure Meta case Dimensions (L x W x H) Weight Mode 240 x 152 x 44mm [9.4 x 6 x 1.7 ] Package 494 x 225 x 70mm [1'6" x 8.9" x 2.8"] Carton 510 x 380 x 252mm [1'7" x 1'2" x 10"] Mode Package Fixedness Power suppy Power Consumption Operation temperature Storage temperature Reative humidity 1U rack-mount with ears and Wa hanging hoes 5V 4A DC 5 W (without audio output) 0~40 C [32~104 F] -20~60 C [-4~140 F] 20~90% RH [no condensation] CONNECTION DIAGRAM 2

5 3

6 PANEL DESCRIPTIONS ML-200 Front Pane 1. Contro buttons: 720p/1080i/1080p/Genock/Source seection 2. VGA IN: Connect to a VGA source 3. HDMI IN: Connect to a HDMI source 4. USB: Firmware update and contro port Rear Pane 5. OUTPUT 1-2: 3G/HD/SD-SDI output 6. Ref IN: Connect to a reference source 7. Ref Loopout: reference oopout 8. Line Leve Output 1-2: Audio output from HDMI input 9. 8ch LINE Leve Output: Audio output from HDMI input 10. Power Switch: Power ON/OFF switch V DC: Interocking power jack for 5V DC power suppy unit 4

7 System Requirement 1. OS information: MS WinXP/7/8 2. Software size: 6MB OPERATION APPROACH Software Contro through USB port 3. Minimum RAM requirement: 256MB Contro Interface Connection Status 2 COM Port Seection 3 I/O Setting Tab 4 Image Setting Tab 5 Image Adjustment Tab 6 Genock Setting Tab 7 Advanced System Setting Tab 1. Connection Status Show the connect information and status. 2. COM Port Seection Use Mini-USB to connect the port on device and computer. Seect correct COM port to contro the device. 5

8 3. I/O Setting Tab (1) Source Seect Set the input source (HDMI/VGA). (2) Output Resoution Set the output resoution. (3) HDMI Output Mode Set the HDMI Output Mode (RGB/YCC444/YCC422/DVI). (4) VGA YCBCR Coor Swap Set the VGA coor swap function is on or off. 6

9 4. Image Setting Tab (1) Coor Setting In here, user can adjust the contrast, brightness, saturation, hue and sharpness of HDMI output and SDI output. The button ets the setting to do defaut reset process. (2) Coor Tone It has three coor tone modes (Off/Skin/Green) for you to seect. (3) Edge Enhance It has five modes (Typ/Mid/Max/User/Off) for you to set up the edge enhance of image. (4) B/W Extension 7

10 5. Image Adjustment Tab User can change the video in vertica or horizonta mirror and arbitrariy shift the video on horizonta direction or vertica direction. Move one pixe at a time. The defaut reset process. button ets the setting to do 6. Genock Setting Tab (1) Genock mode status It can on/off the genock function (Genock/Free Run). (2) Cock Offset Fine tune the cock offset of genock function. If you seect the free run function (off the genock), 8

11 this part wi be bocked. (3) Cock Phase Offset User can fine tune the horizonta or vertica offset. If you off the genock function, this part wi be bocked. 7. Advanced System Setting Tab (1) Firmware Version Read the firmware version. (2) Firmware Update Ø Make sure your mini-usb is connecting. Ø Cick button to enter the interface. Ø Cick button to seect the firmware fie which you want to update. Ø Cick button and the firmware wi start to update. (3) Factory Reset Cick button to do factory defaut reset. 9

12 WARRANTY The SELLER warrants the ML-200 HDMI to SDI Scaer Converter with Genock function free from defects in the materia and workmanship for 1 year from the date of purchase from the SELLER or an authorized deaer. Shoud this product fai to be in good working order within 1 year warranty period, The SELLER, at its option, repair or repace the unit, provided that the unit has not been subjected to accident, disaster, abuse or any unauthorized modifications incuding static discharge and power surge. This warranty is offered by the SELLER for its BUYER with direct transaction ony. This warranty is void if the warranty sea on the meta housing is broken. Unit that fais under conditions other than those covered wi be repaired at the current price of parts and abor in effect at the time of repair. Such repairs are warranted for 90 days from the day of reshipment to the BUYER. If the unit is deivered by mai, customers agree to insure the unit or assume the risk of oss or damage in transit. Under no circumstances wi a unit be accepted without a return authorization number. The warranty is in ieu of a other warranties expressed or impied, incuding without imitations, any other impied warranty or fitness or merchantabiity for any particuar purpose, a of which are expressy discaimed. Proof of sae may be required in order to caim warranty. Customers outside Taiwan are responsibe for shipping charges to and from the SELLER. Cabes and power adapters are imited to a 30 day warranty and must be free from any markings, scratches, and neaty coied. The content of this manua has been carefuy checked and is beieved to be accurate. However, The SELLER assumes no responsibiity for any inaccuracies that may be contained in this manua. The SELLER wi NOT be iabe for direct, indirect, incidenta, specia, or consequentia damages resuting from any defect or omission in this manua, even if advised of the possibiity of such damages. Aso, the technica information contained herein regarding the ML-200 features and specifications is subject to change without further notice. 10