Fieldbus System. New. New. Series EX260 IP67. Drives up to 32 solenoids. Daisy-chain wiring communication. Compact 28mm

Transcription

1 Fieldbus System (Output device for driving port solenoid valves) New Compact 8mm (ctual size) Space-saving Installation IP67 RoHS EtherNet/IP added! For units with D-sub connector, and when connected to S0700 manifolds, it is IP0. Drives up to solenoids Daisy-chain wiring communication pplicable Fieldbus protocols New Top ported valve ottom ported valve Side ported valve Mixed valve sizes manifold 7 mm width valve Series EX60 IP67 IP67 IP67 IP0 CT.EU0--UK

2 E Manifold length is shortened by the small fieldbus output module (SI unit). 8. mm 8 mm Wiring and piping from the same direction is possible. (for side ported) Effective for installation in locations where space is limited above the valve. Existing model EX0 External branch connector is not necessary. Daisy-chain wiring is possible. Reduced wiring space EX60 ranch connector Existing model (EX0) External terminating resistor is not necessary. (Only available for PROFIUS DP, CC-Link communication connectors) ON/OFF switching is possible with an internal terminating resistor. External terminating resistor is not necessary. External terminating resistor Product Specification Variations Number of outputs Output polarity PNP NPN PNP NPN PNP NPN PNP NPN PNP NPN PNP NPN / P E Communication connector D-sub Internal terminating resistor Communication connector examples P / E SI unit Features Fieldbus communication connector (PROFIUS DP) D-sub communication connector (PROFIUS DP)

3 Series SY000/000 Pressure switch Valve piping direction variations Piping is possible from directions. Top ported <Example of Use> ottom ported Side ported y mounting top ported valves on side ported and bottom ported type manifolds, it is possible to detect the output of the / port with a pressure switch. Side ported Mixed mounting of top ported and side ported is possible. Valves can be freely connected up to stations. Mixed valve sizes manifold It is possible to connect only the number of valves required, from to stations, to suit the application. (Maximum number of solenoids connected: ) Series S0700 Valves of different sizes, SY000 and SY000, can be mounted on the same manifold. It is possible to connect only the number of 7 mm width valves required, from to stations. (Maximum number of solenoids connected: ) 7 mm width valves can be connected. pplicable Valve Series Flow-rate characteristics (/ /) Maximum Q[l/min] number of C [dm/(s bar)] b (NR)Note ) solenoids Series SY Power consumption [W] Enclosure 0. (standard) 0. (with powersaving circuit) IP67 page 7 0. IP0 page IP67 8 SY000 S S0700 S SV000 S SV Standards Page page SV VQC (standard) VQC VQC IP67 page 9.0 (standard) Note ) For units with D-sub communication connector, it is IP0. Note ) These valves have been calculated according tp ISO68 and indicate the flow rate under standard conditions with an inlet pressure of 0.6 MPa (relative pressure) and a pressure drop of 0. MPa. Features

4 Fieldbus System Variations IP67/6 specification models I/O separated type I/O integrated type Valve outputs only Inputs only Gateway-type valve outputs only inputs only Valve outputs with multiple I/O s Valve outputs with inputs Number of valve outputs EX60 EX6 EX EX00 EX600 EX0 Number of inputs Number of valve outputs Number of inputs SI unit series EX60 None EX6 EX (total 6) (total 6) EX60 EX00 EX600 EX0 PROFINET EtherCT Open network EtherNet/IP PROFIUS DP DeviceNet CC-Link S-Interface CNopen CompoNet SY (Plug-in connector connecting base) S0700 (Stacking base) 0700 pplicable valve series SV VQC VQ Features

5 Fieldbus System Variations IP0 specification models I/O separated type I/O integrated type Valve outputs only Inputs only Gateway-type valve outputs only inputs only Valve outputs with multiple I/O s Valve outputs with inputs Number of valve outputs EX0 EX EX EX0 EX80 EX0 Number of inputs Number of valve outputs Number of inputs SI unit series EX0 (total 6) None (total 6) EX EX EX0 EX80 EX0 pplicable valve series Open network PROFINET EtherCT EtherNet/IP PROFIUS DP DeviceNet CC-Link S-Interface CNopen CompoNet SY (Plug-in connector connecting base) SJ SY (Plug-in metal base) S0700 (ar stock) SY (ar stock) SY (Stacking base) SV VQ SQ SZ VQZ SYJ Features

6 D D D D SI Unit Integrated-type/For Output Series EX60 RoHS Note) Compact design Number of outputs Output polarity Enclosure Internal terminating resistor Compact design for space saving Each / digital output type available in the series Each negative common (PNP) / positive common (NPN) type available in the series IP67 (For units with D-sub connector, and when connected with S0700 manifolds, it is IP0.) ON/OFF switching is possible with an internal terminating resistor for communication. (Only for units compatible with PROFIUS DP, CC-Link communication connectors) SY000/000 VQC000/000/000 S0700 SV000/000/000 Note) The SY000/000, VQC000/000/000, and S0700 are not yet UL-compatible. EX60 S PR How to Order SI Units Communication protocol Symbol Protocol Number of outputs SI unit output polarity Communication connector Manifold symbol DN Source/PNP (Negative common) QN DN Sink/NPN (Positive common) Q DeviceNet DN Source/PNP (Negative common) QN DN Sink/NPN (Positive common) Q PR Source/PNP (Negative common) NN PR Sink/NPN (Positive common) N PR Source/PNP (Negative common) NN PR Sink/NPN (Positive common) N PROFIUS DP PR Source/PNP (Negative common) NCN PR6 Sink/NPN (Positive common) D-sub PR7 Note) NC Source/PNP (Negative common) NDN PR8 Sink/NPN (Positive common) ND MJ Source/PNP (Negative common) VN MJ Sink/NPN (Positive common) V CC-Link MJ Source/PNP (Negative common) VN MJ Sink/NPN (Positive common) V EC Source/PNP (Negative common) DN EC Sink/NPN (Positive common) D EtherCT EC Source/PNP (Negative common) DN EC Sink/NPN (Positive common) D PN Source/PNP (Negative common) FN PN Sink/NPN (Positive common) F PROFINET PN Source/PNP (Negative common) FN PN Sink/NPN (Positive common) F EN Source/PNP (Negative common) EN EN Sink/NPN (Positive common) E EtherNet/IP EN Source/PNP (Negative common) EN EN Sink/NPN (Positive common) E Note) Enclosure is IP0 when the communication connector is D-sub.

7 Integrated-type/For Output Series EX60 SI Unit Specifications pplicable system Model Protocol I/O occupation area (Inputs/Outputs) Communication speed Power supply for control Power supply for output Power supply for communication Communication connector specification Terminating resistor switch Output Environmental resistance Standards Weight Version Note ) Configuration file Note ) Power supply voltage Internal current consumption Power supply voltage Power supply voltage Internal current consumption Mounting screw ccessories Seal cap (for connector socket) EX60-SPR/ EX60-SPR/ EX60-SPR/7 EX60-SPR6/8 EX60-SDN/ EX60-SDN/ EX60-SMJ/ EX60-SMJ/ PROFIUS DP DeviceNet CC-Link DP-V0 Volume (Edition.) Volume (Edition.) Ver..0 GSD file EDS file SMJ: / SMJ: / SPR: 0/ SPR: 0/ SPR: 0/ SPR6: 0/ SDN: 0/ SDN: 0/ SMJ: / SMJ: / SPR: 0/ SPR: 0/ SPR7: 0/ SPR8: 0/ SDN: 0/ SDN: 0/ ( station, remote I/O stations) ( station, remote I/O stations) k/0 k/00 kbps 6 k/6 k/. M/ M/0 Mbps uilt-in Source/PNP (Negative common) 9.6 k/9. k/. k/9.7 k/ 87. k/00 k/. M/ M/6 M/ Mbps.6 to 6. VDC 00 m or less Sink/NPN (Positive common) Output type SPR: points SPR: points Number of outputs SPR: points SPR: points Load Supplied voltage SPR: Max..0 Supplied current SPR: Max..0 Enclosure Operating temperature range Operating humidity range Withstand voltage Insulation resistance D-sub Source/PNP (Negative common).8 to 6. VDC to VDC 00 m or less None Sink/NPN (Positive common) Source/PNP (Negative common) Sink/NPN (Positive common) EX9-WTS ( pc.) EX9-WTS ( pc.).6 to 6. VDC 00 m or less uilt-in Source/PNP (Negative common) SPR: points SPR6: points SDN: points SDN: points SMJ: points SPR7: points SPR8: points SDN: points SDN: points SMJ: points Solenoid valve with protective circuit for surge voltage of VDC/. W or less (SMC) VDC SPR: Max..0 SPR: Max..0 SPR6: Max..0 SDN: Max..0 SDN: Max..0 SMJ: Max..0 SPR: Max..0 SPR7: Max..0 SPR8: Max..0 SDN: Max..0 SDN: Max..0 SMJ: Max..0 IP67 IP0 IP67 0 to 0 C to 8%RH (No condensation) 00 VC for minute between terminals and housing 0 MΩ or more (00 VDC measured via megohmmeter) between terminals and housing CE marking, UL (CS) compatible 00 g pcs. Sink/NPN (Positive common) SMJ: points SMJ: points SMJ: Max..0 SMJ: Max..0 EX60 SY SV pplicable system Model Protocol I/O occupation area (Inputs/Outputs) Communication speed Power supply for control Power supply for output Power supply for communication Internal current consumption Communication connector specification Terminating resistor switch Output Version Note ) Configuration file Note ) Power supply voltage Internal current consumption Power supply voltage Power supply voltage Output type Enclosure Operating temperature range Environmental Operating humidity range resistance Withstand voltage Insulation resistance Standards Weight Mounting screw ccessories Seal cap (for connector socket) EX60-SEC/ EX60-SEC/ EX60-SPN/ EX60-SPN/ EX60-SEN/ EX60-SEN/ EtherCT Note ) PROFINET Note ) EtherNet/IP Note ) Conformance PROFINET Specification Volume (Edition.8) Test Record V.. Version. Volume (Edition.9) XML file GSD file EDS file SEC: 0/ SEC: 0/ SPN: 0/ SPN: 0/ SEN: / SEN: / SEC: 0/ SEC: 0/ SPN: 0/ SPN: 0/ SEN: / SEN: / 00 Mbps Note ) 0 M/00 Mbps Note ).6 to 6. VDC 00 m or less.8 to 6. VDC None Source/PNP (Negative common) Sink/NPN (Positive common) Source/PNP (Negative common) Sink/NPN (Positive common) Source/PNP (Negative common) Sink/NPN (Positive common) Number of outputs SEC: points SEC: points SPN: points SPN: points SEN: points SEN: points SEC: points SEC: points SPN: points SPN: points SEN: points SEN: points Load Solenoid valve with protective circuit for surge Solenoid valve with protective circuit for surge Solenoid valve with protective circuit for surge voltage of VDC/. W or less (SMC) voltage of VDC/.0 W or less (SMC) voltage of VDC/. W or less (SMC) Supplied voltage VDC Supplied voltage SEC: Max..0 SEC: Max..0 SPN: Max..0 SPN: Max..0 SEN: Max..0 SEN: Max..0 SEC: Max..0 SEC: Max..0 SEN: Max..0 SEN: Max..0 SPN: Max..0 SPN: Max..0 IP67 0 to 0 C to 8%RH (No condensation) 00 VC for minute between terminals and housing 0 MΩ or more (00 VDC measured via megohmmeter) between terminals and housing CE marking, UL (CS) compatible 00 g pcs. EX9-WTS ( pc.) Note ) Please note that the version is subject to change. Note ) Use a CT or higher transmission cable for EtherCT, PROFINET, EtherNet/IP. Note ) Each file can be downloaded from the SMC website, VQC S0700

8 Series EX60 SI Unit Dimensions communication connector type D-sub communication connector type Functions of SI Unit Parts <LED indication and setting switch> <Setting switch> Note) The setting switch varies depending on the model. Refer to the operation manual for details. Please download it via the SMC website, <LED indication> <Connector> communication connector type Part no. Communication protocol Communication connector () US OUT Communication connector () US IN Ground terminal Power connector () D-sub communication connector type EX60-SPR/-SPR -SPR/-SPR PROFIUS DP pins, socket, code pins, plug, code pins, plug, code Part no. Communication protocol Ground terminal Communication connector (D-sub) US IN/OUT Power connector () EX60-SDN DeviceNet pins, socket, code pins, plug, code pins, plug, code M EX60-SPR/-SPR6/-SPR7/-SPR8 PROFIUS DP M 9 pins, socket pins, plug, code EX60-SMJ CC-Link pins, socket, code pins, plug, code EX60-SEC EX60-SPN EX60-SEN EtherCT PROFINET EtherNet/IP pins, socket, D code pins, socket, D code pins pins, plug, code Note), pins Note), plug, code Note ) For EtherCT, PROFINET Note ) For EtherNet/IP

9 The man-hours can be decreased because no exclusive tools (such as solder, crimped terminal) are required. lso, the wire length can be adjusted at the site. QUICKON-ONE P. Piercecon P. Spring-cage Connection P. M8 White The coloring and number indication to the electrical connection makes less wrong wiring. rown lue M8 lack Just insert the connector and make / rotation. Knurl rown lue lign here. Make / rotation. White lack CT.ES00-7 Integrated-type/For Output Series EX60 ccessories q Communication cable with connector For SI units compatible with PROFIUS DP, DeviceNet, CC-Link For SI units compatible with EtherCT, PROFINET, EtherNet/IP Refer to the catalog (CT. ES00-7) for details. EX9 C 00 Cable length (L) M8/ Connector Conforming to IEC Fieldwireable Connectors [mm] Reduction in wiring time [mm] [mm] RJ- SPEEDCON Reduction in wiring time [mm] [mm] IP67 (IEC609) Conforming to IEC EN ø6.7 PSRJ 7. L Connector specification PSRJ plug (straight) RJ- connector EX Plug connector pin arrangement Terminal no. Terminal no. Connections (Straight cable) Core wire colors White Orange Pair White Pair 6 Green 7 8 Shield Plug connector pin arrangement D code SY For SI units compatible with EtherCT, PROFINET, EtherNet/IP PC 666 Cable length [mm] SV ø SPEEDCON (ø6.) Terminal no. Wire guide colour Yellow: TD+ White: RD+ Orange: TD lue: RD Plug connector pin arrangement D code VQC Connections For SI units compatible with EtherCT, PROFINET, EtherNet/IP Fieldwireable connector PC 6 S ø7. ø9 Width across flats Width across flats Plug connector pin arrangement D code

10 Series EX60 ccessories w Power cable with connector (for SI units) For SI units compatible with PROFIUS DP, DeviceNet, EtherCT, PROFINET, EtherNet/IP EX00 P 00 Cable length (L) [mm] [mm] Straight connector type S Connector specification S Straight ngle ngle connector type ø PC ø6 L 0 0 Connections (PROFIUS DP/EtherCT) For SI units compatible with CC-Link Straight connector type Socket connector pin arrangement code code Core wire colours rown: VDC +0%/ % (Solenoid valve power supply) White: 0 V (Solenoid valve power supply) lue: VDC ±0% (Control power supply) lack: 0 V (Control power supply) Grey: Not connected e Seal cap: For connector socket Use this on ports that are not being used for communication connector ( connector socket). Use of this seal cap maintains the integrity of the IP67 enclosure. Note) Tighten the seal cap with the prescribed tightening torque. (For : 0. N m) EX9 SPEEDCON Cable length (L) [mm] [mm] [mm] Terminal no. EX9 C 00 Cable length (L) [mm] [mm] [mm] PC 080 SPEEDCON Cable length (L) [mm] [mm] [mm] W TS Connector type TS For connector socket (0 pcs.) 8. Socket connector pin arrangement ø.8. ø.8 L 8. SPEEDCON Terminal no. SPEEDCON Terminal no. Connections. ø6 L 0. Core wire colours Connections (DeviceNet, EtherNet/IP ) L ø Cable core wire colours x For connector socket 0 0. L 0 ø.0±0. Socket connector pin arrangement code rown: Not connected Note ), VDC ±0% (Control power supply) Note ) White: VDC +0%/ % (Solenoid valve power supply) lue: Not connected Note ), 0 V (Control power supply) Note ) lack: 0 V (Solenoid valve power supply) Grey: Not connected Note ) For DeviceNet Note ) For EtherNet/IP Socket connector pin arrangement code 0807 ø.0±0. 0 Socket connector pin arrangement code rown: VDC +0%/ % (Solenoid valve power supply) White: 0 V (Solenoid valve power supply) lue: VDC ±0% (Control power supply) lack: 0 V (Control power supply) Grey: Not connected

11 Manifold Solenoid Valves for Series EX60 Integrated-type (For Output) Serial Transmission System EX60 Series SY000/000 Page 7 SY Series SV000/000/000 Page SV Series VQC000/000/000 Page 9 VQC Series S0700 Page 8 S0700 6

12 Type 0 Side Ported Type ottom Ported Plug-in Connector Connecting ase: For EX60 Integrated-type (For Output) Serial Transmission System Series SY000/000 q Series w Type 0 SSY SY000 SY000 Side ported ottom ported The SY000 manifold base is used for the bottom ported of the SY000. When ordering, refer to Plug-in Mixed Type Manifold (from page 7). e SI unit specifications Symbol 0 Q Q N N NC ND V V D D F F E EtherNet/IP r SI unit output polarity Positive common N Negative common i, port size (Metric) 0 S N N 0 U C6 q Protocol Number of outputs Communication connector Without SI unit DeviceNet PROFIUS DP D-sub Note) CC-Link EtherCT PROFINET E Note) IP0 for the D-sub applicable communication connector specification. For SI unit part number, refer to page. DIN rail and SI unit output polarity N cannot be selected for the product without SI unit. w t Valve stations In the case of the -output SI unit Symbol Stations Note 0 stations How to Order Manifold stations stations 8 stations stations stations e r t y u i o Double wiring Note ) Specified layout Note ) (vailable up to solenoids) stations In the case of the -output SI unit Symbol Stations Note 0 stations Double wiring Note ) Specified layout Note ) (vailable up to solenoids) Note ) Ensure a match with the common specifications of the valve to be used. Note ) Without SI unit, no symbol is used. Symbol C C C C6 C8 CM L L6 L8 6 8 LM, port ø ø. ø ø6 ø8 Straight port, mixed sizes ø ø6 ø8 ø ø6 ø8 Elbow port, mixed sizes (Including upward and downward piping) SY000 SY000 SY000 P, E port size (s) ø8 ø0 ø0 7 Refer to page for Type /ottom ported dimensions. Straight Upward Elbow Downward Type 0/ Side ported Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly (Refer to the SY000/ 000 series catalogue). Note ) Double wiring: -position single, double, -position and -position valves can be used on all manifold stations. Use of a -position single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. Note ) Specified layout: Indicate the wiring specifications on the manifold specification sheet. (Note that -position double, -position and -position valves cannot be used where single wiring has been specified.) Note ) Includes the number of blanking plate assemblies. Note ) For the model without the SI unit (S0), note the maximum number of solenoids of the SI unit that will be mounted. If the layout is specified, indicate it on the manifold specification sheet. Type / ottom ported, port size (Inch) Symbol Elbow Downward, port y P, E port entry U U side ( to 0 stations) D D side ( to 0 stations) oth sides ( to stations) u SUP/EXH block assembly S R 0 Internal pilot Internal pilot, uilt-in silencer External pilot Direct mounting Without DIN rail (with bracket) For stations For stations SY000 N N N7 N9 CM LN LN7 LN9 N N7 N9 LM ø/8" ø/" ø/" ø/" Straight port, mixed sizes ø/" ø/" ø/" ø/" ø/" ø/" Elbow port, mixed sizes (Including upward and downward piping) P, E port size (s) ø/" Straight Upward /(E) port is plugged for the built-in silencer type. When the built-in silencer type is used, keep the exhaust port from coming in direct contact with water or other liquids. o Mounting and Option Symbol Mounting Option None Direct mounting Name plate (With station number) Name plate (Without station number) D Without name plate DIN rail Name plate (With station number) mounting Name plate (Without station number) Note ) Enter the number of stations inside. (Refer to DIN Rail Option below.) Note ) Only direct mounting is available for Type (ottom ported). DIN Rail Option Specify a longer rail than the total length of specified stations. SY000 SY000 ø/8" Type / ottom ported ø/8" RoHS When it is necessary to mount a DIN rail without an SI unit, select D0 and order DIN rail length separately, referring to L in the dimensions. Refer to the SY000/000 series catalogue for part numbers of DIN rail. Type 0/ Side ported Indicate the sizes on the manifold specification sheet in the case of CM, LM. The direction of P, E port fittings is the same as for, port. If selecting LM, indicate it on the manifold specification sheet for the P, E port fitting direction.

13 Plug-in Connector Connecting ase Series SY000/000 How to Order Manifold ssembly Example (SSY-0SNN-) -position single ( VDC) -position double ( VDC) SY00-U ( sets) SY00-U ( set) -position closed center ( VDC) SY00-U ( set) SSY-0SNN-0D-C6 set (Type 0 -station manifold base part no.) SY00-U sets (-position single part no.) SY00-U set (-position double part no.) SY00-U set (-position closed center part no.) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the valve, etc. EX60 Manifold base ( stations) SSY-0SNN-0D-C6 U side D side Stations Specify on a manifold specification sheet if plugs are required on SY How to Order Valves (With two mounting screws) Refer to the SY000/000 series catalogue for details on valve specifications. q Series e Seal type 0 r Pilot type R t SY 0 0 SY000 SY000 Rubber seal Metal seal Internal pilot External pilot q w w Type of actuation -position single -position double -position closed centre -position exhaust centre -position pressure centre C ack pressure check valve (uilt-in valve type) H None uilt-in the manifold installed type at the same time e r t y u i o!0! ase mounted K Pilot valve option Coil type Standard T Rated voltage VDC Light/surge voltage suppressor and common specification R U S Z NS NZ!0 Manual override : Non-locking push type E: Push-turn locking manual type D: Push-turn locking slotted type F: Slide locking type! Type of mounting screw Round head combination screw Round head combination screw K H gasket separately if it is needed for maintenance part numbers of the base gasket and mounting spacer assembly with residual pressure release SV VQC S0700 class (Mark: ) 8

14 Series SY000/000 Dimensions: Type 0/For EX60/Series SY000 C U SSY-0S- Stations D(S, R) - C, N C, N C6, N7 (D) [Communication connector D-sub] [External pilot]. 7. US P PE X / E P (7.) (.8) [(P), /(E) port] pplicable tube O.D.: ø8, ø/" (Station ) (Station n) [(), () port] pplicable tube O.D.: ø : ø., ø/8" : ø, ø/" : ø6, ø/" [PE: Pilot EXH port] [X: External pilot port] pplicable tube O.D.: ø, ø/" US OUT US IN P P / E / E (Slide locking manual override) US OUT US IN P / E (Pitch) P=0. (7.8) 7..8 (For DIN rail mounting) D side (L) DIN rail holding screw (For DIN rail mounting) Silencer (exhaust port) (uilt-in silencer specification) DIN rail L Light/surge voltage suppressor 8 U side Manual override ( ) Push-turn locking slotted type: Press, then rotate it. () port side : lue (For rubber seal) : Grey (For metal seal) () port side : Yellow SI unit. (.9) ( ) C6:.6 N7:7..7 L. L (DIN rail mounting hole pitch:.) L.7.6 x M mounting hole (Fitting for the type with P/E ports on U and/or D sides) Note) These figures show the SSY-0SQ-0D-C6. n: stations L L L L L

15 Plug-in Connector Connecting ase Series SY000/000 Dimensions: Type 0/For EX60/Series SY000 U C, N SSY-0S- Stations D(S, R) - C6, N7 ( D) C8, N9 [External pilot] [Communication connector D-sub] 0. (0 ) EX60 US / E P / E X PE (9.8) (.7) P [(P), /(E) port] pplicable tube O.D.: ø0, ø/8" (Station ) (Station n) [(), () port] pplicable tube O.D.:ø, ø/" :ø6, ø/" :ø8, ø/" [PE: Pilot EXH port] [X: External pilot port] pplicable tube O.D.: ø, ø/" SY US OUT US IN P / E P / E (Slide locking manual override) US OUT US IN / E P (Pitch) P= (0.) 7..8 (For DIN rail mounting) D side U side DIN rail holding screw (For DIN rail mounting) Silencer (exhaust port) (uilt-in silencer specification) DIN rail (L) L Light/surge voltage suppressor 8 Manual override Push-turn locking slotted type: ( Press, then rotate it. ) () port side : lue (For rubber seal) : Grey (For metal seal) () port side : Yellow. SV VQC SI unit. (8.) (.9) (Fitting for the type with P/E ports on U and/or D sides). L. L (DIN rail mounting hole pitch:.) L x M mounting hole S0700 Note) These figures show the SSY-0SQ-0D-C8. n: Station L L L L L

16 Series SY000/000 Dimensions: Type /For EX60/Series SY000 U SSY-S- Stations D(S, R) - C, N C6, N7 C8, N9 [Communication connector D-sub] / E / E US P P [(P), /(E) port] pplicable tube O.D.:ø0, ø/8" [(), () port] pplicable tube O.D.:ø, ø/" :ø6, ø/" :ø8, ø/" Cut dimensions for panel mounting Refer to panel cut dimensions for details. US OUT US IN (Slide locking manual override) [External pilot] 0. (0 ) / E X PE P Panel cut dimensions [PE: Pilot EXH port] [X: External pilot port] pplicable tube O.D. C: ø(smc) N: ø/"(smc) (Pitch) P= (0.) 9.7 (Station ) (Station n) (.9) 76.7 (Fitting for the type with P/E ports on U and/or D sides) (9.) 78.9 D side Silencer (exhaust port) (uilt-in silencer specification) DIN rail L Light/surge voltage suppressor U side Manual override Push-turn locking slotted type: ( Press, then rotate it. ) () port side : lue (For rubber seal) : Grey (For metal seal) () port side : Yellow (9.8) (.7).. L. 0.9 x M mounting hole 7 US OUT US IN L x M hole x ø. Note) These figures show the SSY-SQ-0D-C8. n: Stations L L

17 S0700 VQC SV SY EX60

18 Type Top Ported Plug-in Connector Connecting ase: For EX60 Integrated-type (For Output) Serial Transmission System Series SY000/000 RoHS Refer to pages, for Type /Top ported dimensions. SSY S N N 0 U q How to Order Manifold w e r t y u i q Series N SY000 SY000 w SI unit specifications Symbol Protocol Number of outputs Communication connector 0 Without SI unit Q DeviceNet Q N N PROFIUS NC DP ND D-sub Note) V CC-Link V D EtherCT D F PROFINET F E EtherNet/IP E Note) IP0 for the D-sub applicable communication connector specification. For SI unit part number, refer to page. DIN rail and SI unit output polarity N cannot be selected for the product without SI unit. e SI unit output polarity Positive common Negative common Note ) Ensure a match with the common specifications of the valve to be used. Note ) Without SI unit, no symbol is used. r Valve stations In the case of the -output SI unit Symbol Stations Note 0 stations 0 Note ) Double wiring: -position single, double, -position and -position valves can be used on all manifold stations. Use of a -position single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. Note ) Specified layout: Indicate the wiring specifications on the manifold specification sheet. (Note that -position double, -position and -position valves cannot be used where single wiring has been specified.) Note ) Includes the number of blanking plate assemblies. Note ) For the model without the SI unit (S0), note the maximum number of solenoids of the SI unit that will be mounted. If the layout is specified, indicate it on the manifold specification sheet. t P, E port entry U Note) D Note) stations stations stations Double wiring Note ) Specified layout Note ) (vailable up to solenoids) In the case of the -output SI unit Symbol Stations Note 0 stations stations stations stations Double wiring Note ) Specified layout Note ) (vailable up to solenoids) U side ( to 0 stations) D side ( to 0 stations) oth sides ( to stations) Note) y For type S, supply/exhaust block assembly with built-in silencer, choose U or D for P port entry. y SUP/EXH block assembly Internal pilot S Internal pilot, uilt-in silencer R External pilot For built-in silencer type, P and E ports are available on U and D sides. /(E) port is plugged. The silencer exhaust port is located on the opposite side of P, E port entry. (Example: When the P, E port entry is D side, the silencer exhaust port is U side.) When the built-in silencer type is used, keep the exhaust port from coming in direct contact with water or other liquids. u P, E port size (s) Symbol N SY000 ø8 ø/" SY000 ø0 ø/8" For N, sizes are in inches. i Mounting D D0 D D Direct mounting DIN rail mounting (With DIN rail) DIN rail mounting (Without DIN rail) For stations For stations Specify a longer rail than the standard length. When it is necessary to mount a DIN rail without an SI unit, select D0 and order DIN rail length separately, referring to L in the dimensions. Refer to the SY000/000 series catalogue for part numbers of DIN rail.

19 Plug-in Connector Connecting ase Series SY000/000 How to Order Manifold ssembly Example (SSY-SNN-) -position single ( VDC) SY0-U-C6 ( sets) -position double ( VDC) SY0-U-C6 ( set) -position closed center ( VDC) SY0-U-C6 ( set) SSY-SNN-0D set (Type -station manifold base part no.) SY0-U-C6 sets (-position single part no.) SY0-U-C6 set (-position double part no.) SY0-U-C6 set (-position closed center part no.) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the valve, etc. EX60 Manifold base ( stations) SSY-SNN-0D q Series e Seal type 0 r Pilot type R H q w SY000 SY000 Rubber seal Metal seal Internal pilot External pilot None uilt-in D side w Type of actuation -position single -position double -position closed centre -position exhaust centre -position pressure centre -position dual -port valve (N.C./N.C.) -position dual -port valve (N.O./N.O.) C -position dual -port valve (N.C./N.O.) Only rubber seal type is available for the -position dual -port valve. t ack pressure check valve (uilt-in valve type) Only rubber seal type. Manifold installed type is available if the back pressure check valve is required for a valve with metal seal. Refer to the SY000/000 series catalogue for details. However, it is not recommended to use the built-in valve type and the manifold installed type at the same time because it will reduce the flow. The built-in valve type back pressure check valve is not available for the -position type. U side Stations SY 0 C6 Refer to the SMC website or the SY000/000 series catalogue for details on solenoid valve specifications, Common Precautions and Specific Product Precautions. How to Order Valves (With two mounting screws) e r t y u i o!0!!! Top ported y Pilot valve option Standard (0.7 MPa) Quick response type (0.7 MPa) K High pressure type (.0 MPa) Only metal seal type is available for the high pressure type. u Coil type Standard T With power saving circuit (Continuous duty type) e sure to select the power saving circuit type when a valve is continuously energized for long periods of time. Note the specified energizing time when power saving circuit is selected. i Rated voltage VDC o Light/surge voltage suppressor and common specification R With surge voltage suppressor (Non-polar) U With light/surge voltage suppressor (Non-polar) S With surge voltage suppressor (Positive common) Z With light/surge voltage suppressor (Positive common) NS With surge voltage suppressor (Negative common) NZ With light/surge voltage suppressor (Negative common) Only Z and NZ types are available for the product with power saving circuit. Select a valve from R, U, S or Z when the SI unit output polarity is (Positive common). Select a valve from R, U, NS or NZ when the SI unit output polarity is N (Negative common).!0 Manual override : Non-locking push type E: Push-turn locking manual type order from the st station as shown in the figure above. If the arrangement becomes complicated, specify on a manifold specification sheet. D: Push-turn locking slotted type F: Slide locking type!, port size Thread piping Symbol M 0 Symbol C C C C6 C8 Symbol N N N7 N9 Port size M x 0.8 /8 (Metric) and port ø ø. ø ø6 ø8 (Inch) and port ø/8" ø/" ø/" ø/"! Thread type F N T Refer to the SY000/000 series catalogue for details on valve specifications. Rc G NPT NPTF pplicable series SY000 SY000 SY000 SY000 SY000 SY000 Only is available for M.! Type of mounting screw Round head combination screw Hexagon socket head cap screw K Round head combination screw(falling-out-prevention type) H Hexagon socket head cap screw(falling-out-prevention type) For K and H, the valve body cover has a drop prevention construction to stop the mounting screws from falling out when the valve is removed for maintenance etc. When ordering a valve individually, the base gasket is not included. Since the base gasket is attached to the manifold, please order the base gasket separately if it is needed for maintenance service. Refer to the SY000/000 series catalogue for part numbers of the base gasket and mounting screw. and H cannot be selected for the individual SUP/EXH spacer assembly. Protective class class (Mark: ) S0700 VQC SV SY

20 Series SY000/000 Dimensions: Type /For EX60/Series SY000 U SSY-S- Stations D (S, R) (-D) [Communication connector D-sub] [External pilot] [PE: Pilot EXH port] [X: External pilot port] pplicable tube O.D.: ø, ø/" US P (7.8) 6. US OUT US IN / E (Station ) (Station n) (.) P P / E / E (Fitting for the type with P/E ports on U and/or D sides) (Slide locking manual override) C6:77. N7:8. US OUT US IN PE /E P / X P E 7..8 (For DIN rail mounting) (7.) 8.. D side DIN rail holding screw (For DIN rail mounting) [(P), /(E) port] pplicable tube O.D.: ø8, ø/" (L) L Light/surge voltage suppressor 6 (Pitch) P=0. 8 U side Manual override Push-turn locking slotted type: ( Press, then rotate it. ) () port side : lue (For rubber seal) : Grey (For metal seal) () port side : Yellow Silencer (exhaust port) (uilt-in silencer specification) DIN rail PE X. /E P x M mounting hole.7.6 SI unit..7 L. L (DIN rail mounting hole pitch:.) L M x 0.8 [(), () port] [(), () port] pplicable tube O.D.: ø : ø., ø/8" : ø, ø/" : ø6, ø/" Note ) These figures show the SSY-SQ-0D. Note ) For built-in silencer type, a silencer is mounted on the opposite side of U or D side with P or E port. n:stations L L L L L

21 Plug-in Connector Connecting ase Series SY000/000 Dimensions: Type /For EX60/Series SY000 SSY-S- Stations U D (S, R) (-D) [External pilot] [Communication connector D-sub]. EX (69.7) 8.7 US US OUT US IN P / E (Station ) / E P (Station n) (7.) P / E (Fitting for the type with P/E ports on U and/or D sides) (9.) 7..8 (For DIN rail mounting) (Slide locking manual override) US OUT US IN / E X P PE / E P [PE: Pilot EXH port] [X: External pilot port] pplicable tube O.D.: ø, ø/" (6.) SY SV DIN rail holding screw (For DIN rail mounting) [(P), /(E) port] pplicable tube O.D.: ø0, ø/8" D side (L) L Light/surge voltage suppressor.. (Pitch) P= U side Silencer (exhaust port) (uilt-in silencer specification) 8 Manual override Push-turn locking slotted type: ( Press, then rotate it. ) () port side : lue (For rubber seal) : Grey (For metal seal) () port side : Yellow VQC 0. DIN rail SI unit. / E X P.7 PE.7. L L (DIN rail mounting hole pitch:.) L.. 0:. C:. x M mounting hole /8 [(), () port] [(), () port] pplicable tube O.D.: ø, ø/" : ø6, ø/" : ø8, ø/" Note ) These figures show the SSY-SQ-0D. Note ) For built-in silencer type, a silencer is mounted on the opposite side of U or D side with P or E port S0700 n:stations L L L L L

22 Type 0 Side Ported Type ottom Ported SY000 can be mounted onto SY000 size manifold. Plug-in Connector Connecting ase: Plug-in Mixed Mounting Type Manifold For EX60 Integrated-type (For Output) Serial Transmission System Series SY000/000 How to Order Manifold RoHS Refer to page 0 for Type / ottom ported dimensions. q Type 0 Side ported ottom ported w SI unit specifications How to Order Manifold ssembly Example (SSY-M0SNN-) -position double SY00-U( sets) SSY M 0 S N N 0 Mixed Mounting Type It is possible to mount SY000 size valves on all stations. q In this case, there is no need to fill in part i in the order code. However, the manifold block width should be. mm. e SI unit output polarity N Symbol 0 Q Q N N NC ND V V D D F F E E Protocol Number of outputs Communication connector Without SI unit PROFIUS DP D-sub Note) CC-Link EtherNet/IP Note) IP0 for the D-sub applicable communication connector specification. For SI unit part number, refer to page. DIN rail and SI unit output polarity N cannot be selected for the product without SI unit. -position double SY00-U( sets) Manifold base ( stations) SSY-M0F-0D-C86 U w e r t t P, E port entry U U side ( to 0 stations) D D side ( to 0 stations) oth sides ( to stations) Refer to the page on the right for u,i,o C 8 6 y u i o!0 Note ) Without SI unit, no symbol is used. r Valve stations In the case of the -output SI unit In the case of the -output SI unit Symbol 0 0 Stations stations stations stations stations Note Double wiring Note ) Specified layout Note ) Symbol 0 stations. Use of a -position single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. Note ) Specified layout: Indicate the wiring specifications on the manifold specification sheet. been specified.) Note ) Includes the number of blanking plate assemblies. Note ) For the model without the SI unit (S0), note the maximum number of solenoids of the SI unit that will be mounted. If the layout is specified, indicate it on the manifold specification sheet Stations stations 8 stations stations stations Note Double wiring Note ) Specified layout Note ) y SUP/EXH block assembly Internal pilot S Internal pilot, uilt-in silencer R External pilot /(E) port is plugged for the built-in silencer type. When the built-in silencer type is used, keep the exhaust port from coming in direct contact with water or other liquids. D side Stations U side SSY-M0F-0D-C86 set (Type 0 -station manifold base part no.) SY00-U sets (-position double part no.) SY00-U sets (-position double part no.) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the valve, etc. If the arrangement becomes complicated, then indicate on the manifold specification sheet. Note ) In this case, use caution as there is also output on the and port on base side. Specify on a manifold specification sheet if plugs are required on the and port on base side. 7!0 Mounting and Option Mounting Symbol D Direct mounting DIN rail mounting Option None Name plate (With station number) Name plate (Without station number) Without name plate Name plate (With station number) Name plate (Without station number) Note ) Enter the number of stations inside. (Refer to DIN Rail Option below.) DIN Rail Option 0 Standard length Without DIN rail (with bracket) For stations For stations Specify a longer rail than the total length of specified stations. length (manifold block length of mm).] When it is necessary to mount a DIN rail without an SI unit, select D0 and calculate DIN rail length, referring to L in the dimensions on page 9.

23 Plug-in Connector Connecting ase Series SY000/000 u Fitting type Symbol, port C Metric size: Straight one-touch fitting L Metric size: Elbow one-touch fitting for upward Note) Metric size: Elbow one-touch fitting for downward Note) N Inch size: Straight one-touch fitting LN Inch size: Elbow one-touch fitting for upward Note) N Inch size: Elbow one-touch fitting for downward Note) CM Straight port, mixed sizes LM Elbow port, mixed sizes (Including upward and downward piping) Note) Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly. Indicate the sizes on the manifold specification sheet in the case of CM, LM. The direction of P, E port fittings is the same as for, port. If selecting LM, indicate it on the manifold specification sheet for the P, E port fitting direction. Elbow fittings: ø, ø. and ø.8" are not available for the SY000 series. ø, ø., ø.8" and ø/" are not available for the SY000 series. q Series w Type of actuation C e Seal type 0 r Pilot type R How to Order Valves (With two mounting screws) SY000 SY000 -position single -position double -position closed centre -position exhaust centre -position pressure centre -position dual -port valve (N.C./N.C.) -position dual -port valve (N.O./N.O.) -position dual -port valve (N.C./N.O.) Only rubber seal type is available for the -position dual -port valve. Rubber seal Metal seal Internal pilot External pilot q w t ack pressure check valve (uilt-in valve type) None H uilt-in Only rubber seal type. Manifold installed type is available if the back pressure check valve is required for a valve with metal seal. Refer to the SY000/000 series catalogue for details. However, it is not recommended to use the built-in valve type and the manifold installed type at the same time because it will reduce the flow. The built-in valve type back pressure check valve is not available for the -position type. SY 0 0 e r t y u i o!0! ase mounted y Pilot valve option Standard (0.7 MPa) Quick response type (0.7 MPa) K High pressure type (.0 MPa) Only metal seal type is available for the high pressure type. u Coil type Standard T With power saving circuit (Continuous duty type) e sure to select the power saving circuit type when a valve is continuously energized for long periods of time. Note the specified energizing time when power saving circuit is selected. i Rated voltage VDC o Light/surge voltage suppressor and common specification Without light/surge voltage suppressor (Non-polar) R With surge voltage suppressor (Non-polar) U With light/surge voltage suppressor (Non-polar) S With surge voltage suppressor (Positive common) Z With light/surge voltage suppressor (Positive common) NS With surge voltage suppressor (Negative common) NZ With light/surge voltage suppressor (Negative common) Only Z and NZ types are available for the product with power saving circuit. Select a valve from R, U, S or Z when the SI unit output polarity is (Positive common). Select a valve from R, U, NS or NZ when the SI unit output polarity is N (Negative common). i SY000:, port size (Metric) (Inch) Symbol 6 8 Port size ø ø6 ø8 For all stations of SY000 Symbol 7 9 Port size ø/" ø/" ø/" For all stations of SY000 No symbol needs to be specified when fitting type CM, LM is selected. o SY000:, port size (Metric) (Inch) Symbol 6 Refer to the SMC website or the SY000/000 series catalogue for details on solenoid valve specifications, Common Precautions and Specific Product Precautions. Port size ø ø. ø ø6 Symbol 7 Port size ø/8" ø/" ø/" No symbol needs to be specified when fitting type CM, LM is selected. Refer to the SY000/000 series catalogue for details on valve specifications.!0 Manual override : Non-locking push type E: Push-turn locking manual type D: Push-turn locking slotted type F: Slide locking type! Type of mounting screw Round head combination screw Hexagon socket head cap screw K Round head combination screw (Falling-out-prevention type) H Hexagon socket head cap screw (Falling-out-prevention type) For K and H, the valve body cover has a drop prevention construction to stop the mounting screws from falling out when the valve is removed for maintenance etc. When ordering a valve individually, the base gasket is not included. Since the base gasket is attached to the manifold, please order the base gasket separately if it is needed for maintenance service. Refer to the SY000/000 series catalogue for part numbers of the base gasket and mounting screw. and H cannot be selected for the individual SUP/EXH spacer assembly or double check spacer assembly with residual pressure release valve. 8 S0700 VQC SV SY EX60

24 Series SY000/000 Dimensions: Type 0/For EX60/Mixed Mounting Type U SSY-M0S- Stations D (-D) [(), () port] pplicable tube O.D.: ø, ø/" : ø6, ø/" : ø8, ø/" (Station ) (Station n) [(), () port] pplicable tube O.D.: ø : ø., ø/8" : ø, ø/" : ø6, ø/" US OUT US IN P / E P / E. (SY000). (SY000) 9. (SY000). (SY000) (Slide locking manual override) 8.7 [(P), /(E) port] pplicable tube O.D.: ø0, ø/8" 8. 8 (Pitch of SY000) P= (0.) (Pitch of SY000) P= (For DIN rail mounting) DIN rail D side (L) L DIN rail holding screw (For DIN rail mounting) Light/surge voltage suppressor U side 8 Manual override Push-turn locking slotted type: ( Press, then rotate it. ) () port side : lue (For rubber seal) : Grey (For metal seal) () port side : Yellow SI unit. (8.) (.9) (Fitting for the type with P/E ports on U and/or D sides). L L (DIN rail mounting hole pitch:.) L x M mounting hole. Note ) These figures show the SSY-M0SQ-0D-C86. Note ) Refer to page 0 for dimensions of D-sub communication connector, external pilot and built-in silencer. EX60 Serial transmission Calculation of dimensions L =. x n + x n L =. x n + x n + 8 M = L/. + Remove all numbers after the decimal L =. x M + L = L 0. L = (L L)/ n: SY000 Valve stations n: SY000 Valve stations 9

25 Plug-in Connector Connecting ase Series SY000/000 Dimensions: Type /For EX60/Mixed Mounting Type SSY-MS- Stations U D / E 8 P [(P), /(E) port] pplicable tube O.D.: ø0, ø/8" / E P [(), () port] pplicable tube O.D.: ø, ø/" : ø6, ø/" : ø8, ø/" (Pitch of SY000) P = (Pitch of SY000) P =. (0.) (Station ) (Station n) 9.7 (SY000) 9.6 (SY000) (SY000) (SY000) Cut dimensions for panel mounting Refer to panel cut dimensions for details. [(), () port] pplicable tube O.D.: ø : ø., ø/8" : ø, ø/" : ø6, ø/" Panel cut dimensions L x M hole x ø. EX60 SY 76.7 US OUT US IN (Slide locking manual override) SV (.9) (9.) (SY000) D side (Fitting for the type with P/E ports on U and/or D sides) L Light/surge voltage suppressor.7 (7.) (SY000) U side Manual override Push-turn locking slotted type: ( Press, then rotate it. ) () port side : lue (For rubber seal) : Grey (For metal seal) () port side : Yellow VQC SI unit x M mounting hole S L. 0.9 Note ) These figures show the SSY-MSQ-0D-C86. Note ) Refer to page for dimensions of D-sub communication connector, external pilot and built-in silencer. EX60 Serial transmission Calculation of dimensions L =. x n + x n L =. x n + x n + 8 n: SY000 Valve stations n: SY000 Valve stations 0

26 Type Top Ported SY000 can be mounted onto SY000 size manifold. Plug-in Connector Connecting ase: Plug-in Mixed Mounting Type Manifold For EX60 Integrated-type (For Output) Serial Transmission System Series SY000/000 How to Order Manifold RoHS Refer to page for Type / Top ported dimensions. SSY S N N 0 U How to Order Manifold ssembly Example (SSY-SNN-) SY0-U-C8 ( sets) Mixed Mounting Type It is possible to mount SY000 size valves on all stations. However, the manifold block width should be. mm. q SI unit specifications Communication connector 0 Without SI unit Q Q N N NC ND Note) V V D D F F E EtherNet E SY0-U-C6( sets) ( stations) SSY-F-0D D side Stations U side e Valve stations SSY-F-0D set (Type -station manifold base part no.) SY0-U-C8.. sets (-position double part no.) SY0-U-C6.. sets (-position double part no.) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the valve, etc. side. In the case of the -output SI unit 0 Stations stations Note 0 stations stations stations q w e r t y w SI unit output polarity N Note ) Note ) Note ) stations. r P, E port entry U Note) D Note) u Mounting D D0 D For stations D For stations u In the case of the -output SI unit Stations Note 0 stations stations stations stations Note ) Note ) U side ( to 0 stations) D side ( to 0 stations) oth sides ( to stations) Note) S t SUP/EXH block assembly S R y P, E port size (s) ø0 N ø/8" Direct mounting DIN rail mounting (With DIN rail) DIN rail mounting (Without DIN rail)

27 Plug-in Connector Connecting ase Series SY000/000 How to Order Valves (With two mounting screws) SY 0 C6 Refer to the SY000/000 series catalogue for details on valve specifications. EX60 q w e r t y u i o!0!!! Top ported q Series e Seal type 0 r Pilot type R H SY000 SY000 w Type of actuation -position single -position double -position closed centre -position exhaust centre -position pressure centre -position dual -port valve (N.C./N.C.) -position dual -port valve (N.O./N.O.) C -position dual -port valve (N.C./N.O.) Only rubber seal type is available for the -position dual -port valve. Rubber seal Metal seal Internal pilot External pilot t ack pressure check valve (uilt-in valve type) None uilt-in Only rubber seal type. Manifold installed type is available if the back pressure check valve is required for a valve with metal seal. Refer to the SY000/000 series catalogue for details. However, it is not recommended to use the built-in valve type and the manifold installed type at the same time because it will reduce the flow. The built-in valve type back pressure check valve is not available for the -position type. y Pilot valve option Standard (0.7 MPa) Quick response type (0.7 MPa) K High pressure type (.0 MPa) Only metal seal type is available for the high pressure type. u Coil type Standard T With power saving circuit (Continuous duty type) e sure to select the power saving circuit type when a valve is continuously energized for long periods of time. Note the specified energizing time when power saving circuit is selected. i Rated voltage VDC o Light/surge voltage suppressor and common specification Without light/surge voltage suppressor (Non-polar) R With surge voltage suppressor (Non-polar) U With light/surge voltage suppressor (Non-polar) S With surge voltage suppressor (Positive common) Z With light/surge voltage suppressor (Positive common) NS With surge voltage suppressor (Negative common) NZ With light/surge voltage suppressor (Negative common) Only Z and NZ types are available for the product with power saving circuit. Select a valve from R, U, S or Z when the SI unit output polarity is (Positive common). Select a valve from R, U, NS or NZ when the SI unit output polarity is N (Negative common).!0 Manual override : Non-locking push type E: Push-turn locking manual type D: Push-turn locking slotted type F: Slide locking type!, port size Thread piping Symbol M 0 Symbol C C C C6 C8 Symbol N N N7 N9 Port size M x 0.8 /8 (Metric) and port ø ø. ø ø6 ø8 (Inch) and port ø/8" ø/" ø/" ø/"! Thread type F N T Rc G NPT NPTF Only Rc is available for M. pplicable series SY000 SY000 SY000 SY000 SY000 SY000! Type of mounting screw Round head combination screw Hexagon socket head cap screw Round head combination screw K (Falling-out-prevention type) Hexagon socket head cap screw H (Falling-out-prevention type) For K and H, the valve body cover has a drop prevention construction to stop the mounting screws from falling out when the valve is removed for maintenance etc. When ordering a valve individually, the base gasket is not included. Since the base gasket is attached to the manifold, please order the base gasket separately if it is needed for maintenance service. Refer to the SY000/000 series catalogue for part numbers of base gasket and mounting screw. and H cannot be selected for the individual SUP/EXH spacer assembly. S0700 VQC SV SY Refer to the SMC website or the SY000/000 series catalogue for details on solenoid valve specifications, Common Precautions and Specific Product Precautions.