NZQA Expiring unit standard 5713 version 5 Page 1 of 5. Use and maintain shop equipment in the automotive refinishing industry

Transcription

1 Page 1 of 5 Title Use and maintain shop equipment in the automotive refinishing industry Level 3 Credits 6 Purpose This unit standard is for people who work in the automotive refinishing industry. People credited with this unit standard are able to: demonstrate knowledge of equipment used in an automotive refinishing shop; use the equipment; and maintain the equipment. Classification Motor Industry > Vehicle Spraypainting Available grade Achieved Explanatory notes 1 The following legislation and regulations (and subsequent amendments) are relevant to this unit standard and must be followed where applicable: Hazardous Substances and New Organisms Act, 1996; Health and Safety in Employment Act, 1992; Transport (Vehicle Standards) Regulations, 1990; Spray Coating Regulations, When the evidence requirements state to the 'acceptable industry standard', it is assumed that it complies with the product and vehicle manufacturers' standards. Outcomes and evidence requirements Outcome 1 Demonstrate knowledge of equipment used in an automotive refinishing shop. 1.1 Purpose of equipment is identified according to the manufacturer's compressors, spray booths, dust extraction systems, oil lubricating systems, air cleaning systems, air dryers, air line system, floor jack.

2 Page 2 of Principles of how equipment operates are identified according to the manufacturer's piston compressor, hydrovane compressor, rotary compressor, flow through spray booth, down draught spray booth, semi-down draught spray booth, aqua dry units for water borne paints, dust extraction systems both on and off the machine, oil lubricating systems on and off the machine, air line and air cleaning systems, air dryer, floor jack, gun wash machines for solvent and water borne paints, air dryers, air line system, air quality and volume, transformer, floor jack, dustless dry sanding system. 1.3 Causes of air pressure drop between the compressor and air outlet are identified. 1.4 Manufacturer's instructions are identified to enable the equipment to be used according to manufacturer's specifications and the acceptable industry standard. Outcome 2 Use the equipment. 2.1 Air cleaning equipment is used and operated according to manufacturer's specifications, and no moisture and oil comes through the air line. air cleaner and/or transformer and air dryer, air line drain legs. 2.2 Air tools are lubricated and operated according to manufacturer's may include but are not limited to attached to air line, attached to machine, manually. 2.3 Spray booth controls are identified, and the booth is operated according to manufacturer's specifications and the acceptable industry standard. may include but are not limited to flow through, down draught, water wash floor, dry floor, semi-down draught, bake oven. 2.4 Dust extraction equipment is operated according to manufacturer's specifications and the acceptable industry standard. 2.5 Compressor is operated according to manufacturer's 2.6 Air line system is operated according to the acceptable industry standard and there are no air leaks or excessive pressure drop.

3 Page 3 of Floor jack is used according to manufacturer's specifications and there is no damage to vehicle. jacking points on vehicles, keeps vehicle off the ground; using axle stands. 2.8 Safe working practices are carried out when operating the equipment. personal safety; safety of other people; vehicle safety; workshop safety; environmental safety; tool, equipment, and machine safety. Outcome 3 Maintain the equipment. 3.1 Service requirements for air cleaning equipment are identified, and equipment is maintained according to manufacturer's air cleaner, transformer, air line drain legs, air drier, filters. 3.2 Service requirements for oil lubricators are identified, and equipment is maintained according to manufacturer's attached to air line, attached to machine. 3.3 Service requirements for the spray booth relevant to the workplace are identified, and the booth is maintained according to manufacturer's may include but are not limited to flow through, down draught (wet/dry), semi-down draught, bake oven. 3.4 Service requirements for dust extraction equipment are identified, and the equipment is maintained according to manufacturer's specifications and the acceptable industry standard. 3.5 Service requirements for the compressor are identified, and the compressor is maintained according to manufacturer's 3.6 Service requirements for positive pressure respirator are identified, and are carried out according to manufacturer's specifications and the acceptable industry standard. air supply regularly checked, filters regularly checked. 3.7 Air line system is maintained according to manufacturer's dirt and moisture drained regularly, air hose stored when not in use, no loose connections, no leaking air lines.

4 Page 4 of Floor jack is serviced and maintained according to manufacturer's topped up with fluid, no oil leaks. 3.9 Safe working practices are carried out when maintaining the equipment. personal safety; safety of other people; vehicle safety; workshop safety; environmental safety; tool, equipment, and machine safety. Replacement information This unit standard and unit standard 5714 have been replaced by unit standard and unit standard This unit standard is expiring. Assessment against the standard must take place by the last date for assessment set out below. Status information and last date for assessment for superseded versions Process Version Date Last Date for Assessment Registration 1 29 January December 2016 Review 2 20 December December 2016 Revision 3 16 October December 2016 Review 4 26 November December 2016 Rollover 5 19 November December 2016 Accreditation and Moderation Action Plan (AMAP) reference 0014 This AMAP can be accessed at Please note Providers must be granted consent to assess against standards (accredited) by NZQA, or an inter-institutional body with delegated authority for quality assurance, before they can report credits from assessment against unit standards or deliver courses of study leading to that assessment. Industry Training Organisations must be granted consent to assess against standards by NZQA before they can register credits from assessment against unit standards. Providers and Industry Training Organisations, which have been granted consent and which are assessing against unit standards must engage with the moderation system that applies to those standards.

5 Page 5 of 5 Consent requirements and an outline of the moderation system that applies to this standard are outlined in the Accreditation and Moderation Action Plan (AMAP). The AMAP also includes useful information about special requirements for organisations wishing to develop education and training programmes, such as minimum qualifications for tutors and assessors, and special resource requirements.