Technical Data for Air Prep Products Filters, Regulators, Lubricators, Desiccant Dryers And Accessories

Transcription

1 Technical Data for Air Prep Products Filters, Regulators, Lubricators, Desiccant Dryers And Accessories MCW & MCT Series MCG Series Metal Bowls Particulate Filters Coalescing Filters Relieving Regulators Specialty Regulators Lubricators Combination Filters and Relieving Regulators Poly Carbonate Bowl Information.. 15 Desiccant Dryers Lockout Valves Dump Valves TECHNICAL DATA Poly Bowls Introduction Particulate Filters Coalescing Filters Relieving Regulators Lubricators Combination Filters and Relieving Regulators Effective R

2 Particulate Filters Particulate Filters Remove Solid Particle Contaminants Down to 5 Microns and Separate Bulk Liquids. This Type of Filter is Generally Used in Industrial Applications Where Liquid Water and Oil Along with Harmful Particles Must be Removed From the Compressed Air System. A Particulate Filter Should Also be Used as a Pre-filter for a Coalescing Filter. Models MCWF18 and MCWF28 are Modular and Can be Easily Connected to the Same Series Coalescing Filters, Regulators and Lubricators With Joiners, End Blocks and T-brackets. You Can Also Mix and Match Among the Families. The MCWF08 is Also Modular But Has a Different Set of Joiners and Brackets. Our Filters Come Equipped With a 5 Micron Element as Standard, With the Exception of the MCTF602 Series. The Element Has 50-70% More Surface Area than Most Competitors Requiring Less Frequent Cleaning and/or Replacing of the Element. The 5 Micron Filter Element Provides Superior Filtration, Exceptional Service Life and Minimal Pressure Drop. Our Filters Come Equipped With a Manual Twist Drain. It Can be Easily Upgraded to an Automatic Drain. The MCWF03, F08, M08 and B08 Series Can be Changed Prior to Installation or In the Field to an Automatic Piston Drain. All Other Filters Can be Upgraded to an Automatic Mechanical Float Drain. 2

3 Mini Particulate Filters (Polycarbonate Bowl) Construction: Zinc Body, Polycarbonate Bowl, 5 Micron Element and Manual Drain Compact Design Unique Deflector Plate Creates Swirling of the Air Stream Ensuring Maximum Water and Dirt Separation Easily Disassembled for Servicing Without the Use of Tools Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature : 32 F to 125 F Optional Auto Piston Drain: PS408B MCWF03-18PB 1/8 22 MCWF03-25PB 1/4 24 SCFM based on Inlet Pressure of 90 psig with a Subcompact Particulate Filters (Polycarbonate Bowl & Nylon Guard) Construction: Zinc Body, Polycarbonate Bowl, Nylon Bowl Guard, 5 Micron Element and Manual Drain Space Saving Design Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature : 14 F to 125 F Optional Auto Piston Drain: GRP MCWF08-18BG 1/8 25 MCWF08-25BG 1/4 50 TECHNICAL DATA MCW/MCT SERIES Compact Particulate Filters (Metal Bowl) Construction: Zinc Body, Quick Disconnect Aluminum Bowl With Sight Gauge, 5 Micron Element and Barbed Manual Drain Connection With Pipe Away Maximum Supply Pressure: 250 psig (17.2 bar) Operating Temperature: -13 F to 150 F Optional Auto Drain: GRP MCWF /4 110 MCWF /8 120 MCWF /

4 Standard Particulate Filters (Metal Bowl) Construction: Zinc Body, Quick Disconnect Aluminum Bowl With Sight Gauge, 5 Micron Element and Barbed Manual Drain Connection With Pipe Away Maximum Supply Pressure: 250 psig (17.2 bar) Operating Temperature: 13 F to 150 F Optional Auto Drain: GRP MCWF /8 144 MCWF /2 160 MCWF /4 165 Large Particulate Filters (Metal Bowl) Construction: Zinc Body, 16 oz. Zinc Bowl With Sight Gauge, 40 Micron Element and Manual Drain Excellent Water Removal Efficiency For Heavy Duty Applications with Minimum Pressure Drop Requirement Unique Deflector Plate Creates Swirling of the Air Stream Ensuring Maximum Water and Dirt Separation Large Filter Element Surface Guarantees Low Pressure Drop and Increased Element Life Maximum Supply Pressure: 250 psig (17.2 bar) Operating Temperature: 40 F to 150 F Optional 5 Micron Element Available Optional Auto Drain: SA602D MCTF /4 220 MCTF MCTF /4 390 MCTF /2 450 MCTF SCFM based on Inlet Pressure of 90 psig with a Jumbo High Flow Capacity Particulate Filters (Metal Bowl) Construction: Aluminum Body and Bowl With Differential Pressure Indicator (Green/Red When Differential Exceeds 15 psi), 5 Micron Element and Manual Drain Unique Drain Mounting Plate Design Offers a Trouble Free Method for Interchanging and Installing External Drains Maximum Supply Pressure With Differential Pressure Indicator (DPI) : 150 psig (10.3 bar) Operating Temperature: 32 F to 150 F Optional Auto Drain: GRP Drain Plate & GRP Auto Drain MCWF /4 970 MCWF / MCWF

5 Coalescing Filters Coalescing Filters are Specifically Designed for the Removal of Solid Particles, Water and Oil Aerosols Down to 0.01 Micron. Protection of Components Such as Critical Air Control Circuits, Air Logic Systems, Flow and Temperature Controllers, Food Processing, Electronics, Health Care and Pneumatic Gauging are Examples of Specific End-Use Applications Where the Removal of Extremely Fine Particulate and Virtually Oil-Free or High Quality Air is Necessary. Differential Pressure Indicators (DPI) are Standard on Most Coalescing Filters Models. They Provide for a Maintenance Free Means of Determining the Service Life of the Filter Element. With a New Element Installed the DPI Shows All Green and Progresses to Full Red, Indicating the Element Should be Changed. TECHNICAL DATA MCW/MCT SERIES The Elements in the Coalescing Filter Series are Constructed With Achieving the Highest of Air Quality in Mind. Inner and Outer Stainless Steel Support Cylinders, Pure Borosilicate Glass Microfiber Filter Media With No Glues or Resins, Glass Filled Polyamide Material End Caps are Part of the Components Used to Create an Element With % Efficiency. Air Quality Class Confirms to ISO 8573, Exceeding ISU Class 1 for Maximum Particle Size and Concentration of Solid Contaminants and Exceed Class 1 on Maximum Oil Content of 0.01 ppm/wt. 5

6 Subcompact Coalescing Filters (Polycarbonate Bowl & With Guard) Construction: Zinc Body, Quick Disconnect Polycarbonate Bowl, 0.01 Micron Element and Manual Drain High Efficiency Removal of Water, Oil Aerosols and Solid Particulate Contaminants Down to 0.01 ppm/wt. With a Minimum Pressure Drop Light Weight Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature: 14 F to 125 F Optional Elements: 0.5 Micron Micron Activated Carbon Optional Auto Piston Drain: GRP MCWM08-18BG 1/8 11 MCWM08-25BG 1/ psi Pressure Drop All Coalescing Filters Should be Protected by a Particulate Filter i.e. MCWF08 Installed Upstream Compact Coalescing Filters (Metal Bowl) Construction: Zinc Body, Quick Disconnect Aluminum Bowl With Sight Gauge, 0.01 Micron Element, Differential Pressure Indicator (DPI) and Manual Drain High Efficiency Removal of Water, Oil Aerosols and Solid Particulate Contaminants Down to 0.01 ppm/wt With Minimum Pressure Drop Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature: -13 F to 150 F Optional Elements: 0.5 Micron Micron Activated Carbon MCWM /4 40 Optional Auto Drain: GRP MCWM /8 44 MCWM / psi Pressure Drop All Coalescing Filters Should be Protected by a Particulate Filter i.e. MCWF18 Installed Upstream Standard Coalescing Filters (Metal Bowl) Construction: Zinc Body, Quick Disconnect Aluminum Bowl With Sight Gauge, 0.01 Micron Element, Differential Pressure Indicator (DPI) and Manual Drain High Efficiency Removal of Water, Oil Aerosols and Solid Particulate Contaminants Down to 0.01 ppm/wt. With Minimum Pressure Drop Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature: -13 F to 150 F Optional Elements: 0.5 Micron Micron Activated Carbon MCWM /8 82 Optional Auto Drain: GRP MCWM /2 90 MCWM / psi Pressure Drop All Coalescing Filters Should be Protected by a Particulate Filter i.e. MCWF28 Installed Upstream 6

7 Large Coalescing Filters (Metal Bowl) Construction: Zinc Body, Aluminum Bowl, Differential Pressure Indicator, 0.01 Micron Element and Manual Drain High Efficiency Removal of Water, Oil Aerosols and Solid Particulate Contaminants Down to 0.01 ppm/wt With Minimum Pressure Drop Maximum Supply Pressure: 200 psig (13.8 bar) Operating Temperature: 32 F to 150 F Optional Elements: 0.5 Micron Micron Activated Carbon MCWM /2 123 Optional Auto Drain: GRP MCWM /4 173 MCWM psi Pressure Drop All Coalescing Filters Should be Protected by a Particulate Filter i.e. MCWF28 or MCTF602 Installed Upstream Large Coalescing Filters (Metal Bowl) Construction: Zinc Body, 100 oz. Aluminum Bowl, Differential Pressure Pop Up (DOP) Indicator (Turns Red When Pressure Exceeds 15 psi) and Manual Twist Drain Removes Liquid Aerosols and Sub Micron Particles Protect Pneumatic Systems From Contamination that Standard Particulate Filters Will Not Catch High Flow Design Grade 10 Element: DOP Coalescing Efficiency 0.3 to 0.6 Particles 95%, Max Oil Carryover ppm w/w.85 Max. Supply Pressure With Manual Drain: 300 psig Max. Supply Pressure With Auto Drain: 250 psig Max. Temperature with Manual Drain: 32 F to 150 F Max. Temperature with Auto Drain: 32 F to 125 F Optional Auto Drain: SA702MD MCTF701C-75 3/4 285 MCTF701C SCFM based on Inlet Pressure of 100 psig with a TECHNICAL DATA MCW/MCT SERIES All Coalescing Filters Should be Protected by a Particulate Filter i.e. MCTF602 Installed Upstream Jumbo High Flow Capacity Coalescing Filters (Metal Bowl) Construction: Aluminum Body and Bowl, 0.01 Micron Element, Differential Pressure Indicator (DPI) and Manual Drain Unique Drain Mounting Plate Design Offers Trouble Free Method for Interchanging and Installing External Drains Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature: 32 F to 150 F Optional Elements: 1.0 Micron Micron Activated Carbon Optional Auto Drain: GRP Drain Plate & GRP Auto Drain MCWM /2 710 MCWM psi Pressure Drop All Coalescing Filters Should be Protected by a Particulate Filter i.e. MCWF35 Installed Upstream 7

8 Relieving Regulators General Purpose Regulators are Used to Provide a Convenient and Low Cost Method to Reduce Supplied Air Pressure to a Desired Outlet Pressure and Transform a Fluctuating Air Supply to a Relatively Constant Reduced Air Pressure Within the Operating Range of the Regulator. Operation is Simplified by Turning the Adjusting Knob Clockwise Forcing the Main Spring Downward Onto the Flexible Diaphragm Which Presses Down Onto the Valve Stem. The Diaphragm and Valve Stem Move Downward Forcing the Balanced Valve Off its Seat, Which Allows Air to Flow Past the Valve to the Outlet Side of the Regulator and Downstream to the Air System. A Precisely Positioned Aspirator Tube Communicates Secondary Pressure to the Diaphragm Resulting in Instant Compensation in Order to Maintain the Desired Secondary Set Pressure. The Diaphragm, Valve Stem and Valve Move Upward, Compressing the Regulating Main Spring. Upward Movement Stops When the Spring Force Acting on the Diaphragm Balances the Pressure Force Acting Below the Diaphragm. For Best Performance, Regulated Pressure Should Always Be Set by Increasing the Pressure Up to the Desired Setting. For Best Performance Select a Spring Range So That the Desired Secondary Set Pressure Falls in the Middle of the Spring Range. For Example, If the Desired Secondary Set Pressure is 30 psi Select a Regulator With a Spring Range of 0-60 psi. The Regulators are Tamper Resistant by Pushing Down on the Knob and Clicking the Knob Into Place. For Added Protection the Knob May Be Easily Completely Removed After the Desired Regulated Pressure Has Been Selected. 8

9 Mini Relieving Regulators Construction: Zinc Body, Unbalanced Poppet, Solid Control Piston With Lip Seal for Extended Life, Non Rising Adjusting Knob Space Saving Design 2-1/8 NPT Gauge Ports Recommended Gauge: PSB15-XXX Maximum Supply Pressure: 300 psig (20.7 bar) Operating Temperature: 32 F to 125 F Pressure Range: psig (D) Optional Pressure Ranges: 1-60 psig (E) 1-30 psig (F) MCWR /8 13 MCWR /4 15 SCFM based on Inlet Pressure of 100 psig Secondary Pressure of 90 psig Subcompact Relieving Regulators Construction: Zinc Body, Balanced Valve Design Easy to Service and Maintain 2-1/8 NPT Gauge Ports Recommended Gauge: PSB15-XXX Maximum Supply Pressure: 300 psig (20.7 bar) Operating Temperature: -4 F to 150 F Pressure Range: psig (D) Optional Pressure Ranges: 0-60 psig (E) 0-30 psig (F) MCWR /8 29 MCWR /4 44 SCFM based on Inlet Pressure of 100 psig Secondary Pressure of 90 psig TECHNICAL DATA MCW/MCT SERIES Compact Relieving Regulators Construction: Zinc Body, Balanced Valve Design, Spring Loaded Diaphragm 2-1/4 NPT Gauge Ports Recommended Gauge: PSB20-XXX Maximum Supply Pressure: 300 psig (20.7 bar) Operating Temperature: -13 F to 150 F Pressure Range: psig (D) Optional Pressure Ranges: psig (A) 3-60 psig (E) MCWR /4 82 MCWR /8 97 MCWR /2 97 SCFM based on Inlet Pressure of 100 psig Secondary Pressure of 90 psig 9

10 Standard Relieving Regulators Construction: Zinc Body, Balanced Valve Design, Spring Loaded Diaphragm 2-1/4 NPT Gauge Ports Recommended Gauge: PSB20-XXX Maximum Supply Pressure: 300 psig (20.7 bar) Operating Temperature: -13 F to 150 F Pressure Range: psig (D) Optional Pressure Ranges: psig (A) 3-60 psig (E) MCWR /8 162 MCWR /2 170 MCWR /4 176 SCFM based on Inlet Pressure of 100 psig Secondary Pressure of 90 psig Mini Relieving Regulators - Compressed Air Service for Harsh Environments Construction: Brass Body Handles Most Corrosive Environments, Large Diaphragm to Valve Area Ratio for Precise Regulation Space Saving Design Panel Mount Nut Standard 2-1/8 NPT Gauge Ports Recommended Gauge: PSB15-XXX Maximum Supply Pressure: 300 psig (20.7 bar) Operating Temperature: 40 F to 125 F Pressure Range: psig (D) Optional Pressure Ranges: 1-60 psig (E) 1-25 psig (G) MCWRB3-25 1/4 14 SCFM based on Inlet Pressure of 100 psig, Secondary Pressure of 90 psig with a 25% Pressure Drop Specialty Regulators - Water or Compressed Air Pressure Relieving Regulators Designed for Use With Water & Compressed Air Systems Light Weight Plastic Body Constructed With A Combination of NSF and FDA Approved Materials Unbalanced Poppet Standard Non Rising Push to Lock Adjusting Knob Diaphragm Operated Part No. NPT Service Style SCFM 2 1/8 NPT Gauge Ports Non Recommended Gauge: PSB15-XXX MCWR /4 Water 13 Relieving Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature : 40 F to 125 F MCWR /4 Air Relieving 13 Pressure Range: psig (D) SCFM based on Inlet Pressure of 100 Psig Secondary Pressure of 75 psig 10

11 Large Relieving Regulators Construction: Zinc Body, Heavy Duty T-Handle High Flow Performance Featuring Rugged Design for the Most Demanding Applications Diaphragm Operated Design With Balanced Poppet for Quick and Accurate Regulation Ideal for Those Installations Calling for Constant Pressure With Wide Variation in Flow 2-1/4 NPT Gauge Ports Recommended Gauge: PSB20-XXX Maximum Supply Pressure: 300 psig (20.7 bar) MCTR /4 300 Operating Temperature: 40 F to 125 F MCTR Pressure Range: psig (A) Optional Pressure Range: psig (D) MCTR /4 500 MCTR /2 500 Large Relieving Regulators Construction: Zinc Body, Balanced Valve Design Piston Operated 2-1/4 Gauge Ports Recommended Gauge: PSB20-XXX Maximum Supply Pressure: 300 psig (20.7 bar) Operating Temperature: 32 F to 150 F Pressure Range: psig (B) Optional Pressure Range: psig (D) SCFM based on Inlet Pressure of 100 psig Secondary Pressure of 75 psig MCWR /4 481 MCWR MCWR /4 800 SCFM based on Inlet Pressure of 100 psig Secondary Pressure of 80 psig TECHNICAL DATA MCW/MCT SERIES Jumbo High Flow Capacity Relieving Regulators Construction: Zinc Body, Balanced Valve Design Piston Operated 2-1/4 NPT Gauge Ports Recommended Gauge: PSB20-XXX Maximum Supply Pressure: 300 psig (20.7 bar) Operating Temperature: 32 F to 150 F Pressure Range: psig (B) Optional Pressure Range: psig (D) MCWR / MCWR SCFM based on Inlet Pressure of 100 psig Secondary Pressure of 85 psig 11

12 Lubricators For Proper Operation There Must Be Line Pressure in the Lubricator Reservoir Bowl. As the Air Flows Through the Lubricator, Some of the Incoming Air Passes Through the Bowl Pressure Control Valve That Then Pressurizes the Bowl Pushing Oil Upward Through the Siphon Tube. Most of the Air Flow Passes Through the Self-Adjusting Flow-Guide Flow Sensor in the Lubricator Throat Creating a Slight Pressure Drop That is Proportional to the Rate of Air Flow. The Pressure Drop is Sensed by the Sight Dome and Across the Adjustment Needle Valve Allowing Oil to Flow Upward Through the Siphon Tube Into the Sight Dome Where it Drips Into a Nozzle Passage and Then Into the Lubricator Throat. The Precise Amount of Oil to Be Delivered to the Air Stream is Determined By the Oil Adjusting Needle Valve that Sets the Exact Drip Rate. The Oil Drops are Atomized by the High Velocity Air Flowing Through the Lubricator. All of the Drops Visible in the Sight Dome are Delivered Downstream to the Air Devices. The Self-Adjusting Flow Sensor Automatically Maintains a Constant Oil-to-Air Ratio By Opening and Closing in Response to a Wide Range of Changing Air Flows. A Check Valve Keeps the Siphon Tube Full of Oil During Periods of No Flow and Prevents Oil Carry-Over Due to the Possibility of Reverse Flow. The Pressurizing Valve Controls the Rate of Bowl Pressurization and Allows Depressurization for Refilling the Unit Without shutting Off the Supply Air. When the Oil Fill Plug is Loosened, a Spring Loaded, Normally Closed 2-Way Valve Closes, Allowing the Air Pressure in the Bowl to Be Gradually Reduced. When the Fill Plug is Replaced, the Bowl Repressurizes Through the Pressure Control Valve. Upon Initial Use, or If Unit Has Been Run Dry, Open Oil Adjustment Wide Open Until No Air Bubbles are Visible in the Sight Dome. Then Reset Oil Feed Adjustment to Desired Setting. Only Use Clean Oil in the Lubricators. SAE10 or Lightweight Oil is Highly Recommended. 12

13 Subcompact Lubricators (Polycarbonate Bowl With Guard) Construction: Zinc Body, Quick Disconnect Polycarbonate Bowl, Integral Sight Dome, Adjustment Knob and Manual Drain Can Be Filled While Under Pressure Initial Drip Flow: 1.3 scfm Minimum Flow for Lubrication: psig Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature: 14 F to 125 F Recommended Lubricant: Airline Oil F (Equal to ISO VG32 or SAE 10) MCL08-18BG 1/8 23 MCL08-25BG 1/4 57 Compact Lubricators (Metal Bowl) Construction: Zinc Body, Quick Disconnect Aluminum Bowl with Sight Gauge, Integral Sight Dome, Adjustment Knob and Manual Drain Can Be Filled While Under Pressure Initial Drip Flow:.68 scfm Minimum Flow for Lubrication: psi Maximum Supply Pressure: 250 psig (17.2 bar) Operating Temperature: 14 F to 150 F Recommended Lubricant: Airline Oil F (Equal to ISO VG32 or SAE 10) MCWL /4 88 MCWL /8 90 MCWL /2 96 TECHNICAL DATA MCW/MCT SERIES Standard Lubricators (Metal Bowl) Construction: Zinc Body, Aluminum Bowl with Sight Gauge, Integral Sight Dome, Adjustment Knob and Manual Drain Can Be Filled While Under Pressure Initial Drip Flow: 1.26 scfm Minimum Flow for Lubrication: psi Maximum Supply Pressure: 250 psig (17.2 bar) Operating Temperature: 14 F to 150 F Recommended Lubricant: Airline Oil F (Equal to ISO VG32 or SAE 10) MCWL /8 176 MCWL /2 184 MCWL /

14 Large Lubricators (Metal Bowl) Construction: 16 oz. Zinc Bowl with Sight Gauge, Polycarbonate Sight Dome and Manual Drain Can Be Filled While Under Pressure Proportional Oil Delivery Over a Wide Range of Air Flows Precision Needle Valve Assures Repeatable Oil Delivery and Provides Simple Adjustment of Delivery Rates Lubrication 1 Drop for Every SCFM Maximum Supply Pressure: 250 psig (17.2 bar) MCTL /4 325 (Equal to ISO VG32 or SAE 10) Operating Temperature: 40 F to 150 F Recommended Lubricant: Airline Oil F442 MCTL MCTL / MCTL /2 400 SCFM based on Inlet Pressure of 100 psig with a Jumbo High Flow Capacity Lubricators (Metal Bowl) Construction: Zinc Body and 26 Oz. Aluminum Bowl With Sight Gauge, Adjustable Oil Feed and Brass Petcock Drain Siphon Tube Filter Provides Clean Lubricant Downstream Can Be Filled While Under Pressure Initial Drip Flow:.95 scfm Minimum Flow for Lubrication: psig Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature: 32 F to 125 F Recommended Lubricant: F (Equal to ISO VG32 or SAE 10) MCWL /4 927 MCWL /2 927 SCFM based on Inlet Pressure of 120 psig with a Jumbo High Flow Capacity Lubricators (Metal Bowl) Construction: Zinc Body and 26 Oz. Aluminum Bowl With Sight Gauge, Adjustable Oil Feed and Brass Petcock Drain Siphon Tube Filter Provides Clean Lubricant Downstream Can Be Filled While Under Pressure Maximum Supply Pressure: 200 psig (13.8 bar) Operating Temperature: 32 F to 150 F Recommended Lubricant: F (Equal to ISO VG32 or SAE 10) MCWL SCFM based on Inlet Pressure of 120 psig with a 14

15 CAUTION Polycarbonate Bowls, Being Transparent and Tough are Ideal for Use With Filters and Lubricators. They are Suitable for Use in Normal Industrial Environments, But Should Not Be Located in Areas Where They Could Be Subject to Direct Sunlight and Impact Blow Nor Temperatures Outside the Rated Range. As With Most Plastics Some Chemicals Can Cause Damage. Polycarbonate Bowls Should Not Be Exposed to Chlorinated Hydrocarbon, Ketones, Esters and Certain Alcohols. They Should Not Be Used in Air Systems Where Compressors are Lubricated With Fire-Resistant Fluids Such as Phosphate Ester and Diester Types. Metal Bowls are Recommended Where Ambient and /or Media Conditions are Not Compatible With Polycarbonate Bowls. Metal Bowls Resist the Action of Most Such Solvents, But Should Not Be Used Where Strong Acids or Bases Are Present or in Salt Laden Atmospheres. Consult the Factory for Specific Recommendations Where These Conditions Exist. TO CLEAN POLYCARBONATE BOWLS USE MILD SOAP AND WATER ONLY! DO NOT USE Cleansing Agents Such as Acetone, Benzene, Carbon Tetrachloride, Gasoline, Toluene, etc, Which are Damaging to This Plastic. TECHNICAL DATA MCW/MCT SERIES Mini Combination Filter/Relieving Regulator (Polycarbonate Bowl) Construction: Brass Body, Polycarbonate Bowl, Handles Most Corrosive Environments, 5 Micron Element and Manual Drain Regulator Has Large Diaphragm to Valve Area Ratio for Precise Regulation 2-1/8 NPT Gauge Ports Recommended Gauge PSB15-XXX Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature: 40 F to 125 F Pressure Range: psi (D) Optional Pressure Ranges: 1-60 psi (E) 1-25 psi (G) Optional Piston Drain GRP MCWBB3-25DPB 1/4 16 SCFM based on Inlet Pressure of 100 psig, Secondary Pressure of 75 psi. 15

16 Subcompact Combination Filter/Regulator (Polycarbonate Bowl With Guard) Construction: Zinc Body With Quick Disconnect Polycarbonate Bowl Nylon Guard, 5 Micron Element and Manual Drain Regulator Has Balanced Valve Design 2-1/8 NPT Gauge Ports Recommended Gauge PSB15-XXX Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature: 14 F to 125 Pressure Range: psig (D) Optional Pressure Range: 0-30 psig (F) Optional Auto Piston Drain GRP MCWB08-18BG 1/8 28 MCWB08-25BG 1/4 42 SCFM based on Inlet Pressure of 100 psig, Secondary Pressure of 90 psi. Compact Combination Filter/Relieving Regulator (Metal Bowl) Construction: Zinc Body With Quick Disconnect Aluminum Bowl, 5 Micron Element and Manual Drain Regulator Has Balanced Valve Design Spring Loaded Diaphragm 2-1/4 Gauge Ports Recommended Gauge: PSB20-XXX Maximum Supply Pressure: 250 psig (17.2 bar) Operating Temperature : 13 F to 150 F Pressure Range: psig (A) Optional Pressure Range: psig (D) MCWB / psig (E) Optional Auto Drain: GRP MCWB /8 117 MCWB /2 121 SCFM based on Inlet Pressure of 100 psig, Secondary Pressure of 90 psi. Standard Combination Filter/Regulator Combination (Metal Bowl) Construction: Zinc Body With Quick Disconnect Aluminum Bowl, 5 Micron Element and Manual Drain Regulator Has Balanced Valve Design Spring and Loaded Diaphragm 2-1/4 NPT Gauge Ports Recommended Gauge: PSB20-XXX Maximum Supply Pressure: 250 psig (17.2 bar) Operating Temperature : 13 F to 150 F Pressure Range: psig (A) Optional Pressure Range: psig (D) 3-60 psig (E) MCWB /8 140 Optional Auto Drain: GRP MCWB /2 165 MCWB /4 175 SCFM based on Inlet Pressure of 100 psig, Secondary Pressure of 90 psi. 16

17 Desiccant Dryers Construction: Zinc Body, Polycarbonate Bowl and Aluminum Guard Helps Eliminates Condensation at Point of Use Atmospheric Dew Point: 45 F No Electrical Connection Necessary Color Change of the Desiccant (Blue to Pink) Provides An Instant Status of the Compressed Air System Total Minutes of Continuous Air Flow: 120 Minutes Maximum Supply Pressure: 150 psi (10.3 bar) Maximum Temperature: 125 F Part No. NPT Bowl Size Maximum Continuous Air Flow MCWX06-25BG 1/4 7 oz. 5 SCFM Desiccant Dryers SCFM is based on dry desiccant at 100 psig and 70 F Construction: Zinc Body, Polycarbonate Bowl and Aluminum Guard (BG) or Metal Bowl (M) Helps Eliminates Condensation at Point of Use Atmospheric Dew Point: 45 F No Electrical Connection Necessary Color Change of the Desiccant (Blue to Pink) Provides An Instant Status of the Compressed Air System Total Minutes of Continuous Air Flow: X Minutes / X Minutes Maximum Supply Pressure: 150 psi (10.3 bar) Maximum Temperature: 125 F (BG) Bowl Part No. NPT 150 F (M) Size The MCWX04 Consists of 2 MCWX03 MCWX /4 1.5 Qts 10 SCFM Assembled Together to Provide Twice the Drying Time, Double the MCWX /4 1.5 Qts 10 SCFM Service Life & Double the Capacity Maximum Continuous Air Flow SCFM is based on dry desiccant at 100 psig and 70 F TECHNICAL DATA MCW/MCT SERIES Desiccant Dryers Construction: Zinc Body, Aluminum 1 Qt. Bowl and Guard with Moisture Indicator Helps Eliminates Condensation at Point of Use Atmospheric Dew Point: 45 F No Electrical Connection Necessary Color Change of the Desiccant (Blue to Pink) Provides An Instant Status of the Compressed Air System Total Minutes of Continuous Air Flow: 440 Minutes Maximum Supply Pressure: 150 psi (10.3 bar) Maximum Temperature: 150 F Part No. NPT Bowl Size Maximum Continuous Air Flow MCWX25-50M 1/2 1 Qt. 25 SCFM SCFM is based on dry desiccant at 100 psig and 70 F 17

18 Safety Lockout Valves The Safety Lockout Valve is a Manually Operated Slide Type, 2-Position, 3-Way Valve. In the Closed Position, Downstream Air is Exhausted to Atmosphere. The Valve Slide Can be Locked In the Closed Position With a Customer Supplied Padlock. The Safety Lockout Valves Conform to OSHA #29 CFR part 1910 Control of Hazardous Energy Source (Lockout/Tagout) Part No. Construction: Acetal Blades, Zinc Body, Nitrile Seals Maximum Supply Pressure: 150 psig (10.3 bar) Operating Temperature: 32 F to 150 F NPT SCFM Rating MCWV /4 100 MCWV /4 141 MCWV /8 216 MCWV /2 290 MCWV /4 300 SCFM based on Inlet Pressure of 150 psig Dump Valves The Slow-Start Quick Dump Valve is Designed as a Three Way Quick Dump Valve With a Built In Slow-Start Capability. This Slow-Start Capability Allows Control of the Downstream Pressure Build Up at Start Up of a Compressed Air System. The Combination of Slow-Start and Quick Dump Reduces the Number of Pneumatic Components and the Unique Volume Independent Design Allows Any Number of Additions to the Pneumatic Circuit Without Readjusting the Slow-Start Function Construction: Aluminum Body, Modular Design Part No. NPT SCFM Rating True Volume Independence MCWE /4 95 Choice of Two Exhaust Port Locations MCWE /8 101 Maximum Supply Pressure: 150 psig (10.3 bar) Minimum Pressure: 30 psig (2.1 bar) MCWE /2 113 Operating Temperature: 32 F to 150 F MCWE /8 196 MCWE /2 210 MCWE /4 230 SCFM based on Inlet Pressure of 150 psig Most leading FRL Manufacturers Use Different Inlet Pressures Which Determine the scfm. To Ensure the Best Selection it is Suggested That You Select Your FRL s Based on the Available Inlet Pressure and Flow Needed for the Specific Application. Please See the FRL Pricing Section of Your Midwest Control Catalog for Information on Elements, Replacement Kits and Accessories Offered. In Addition to the FRL Offering We Have Many Other Products In the Midwest Control Catalog. If You Do Not Find What You Are Looking For, Please Call Us. We ll Locate It For You! Remember, Clean, Dry Air is The Corner Stone of an Efficient Air System. 18

19 Midwest Control s FRL s Feature Heavy Duty Aluminum Die Cast Heads and Steel Bowl Guards Which Protects the Polycarbonate Bowl from Damage as Opposed to Plastic Bodies. Each Filter and Lubricator Unit is Designed to Withstand a Burst Pressure of 1300 PSI, While Each Regulator Is Designed to Withstand a Burst Pressure of 2000 PSI. Each Unit is 100% Factory Tested and Certified for Guaranteed Performance. Filters Incorporate Both a Separator and Shield for Maximum Moisture Separation. Air Line Filters Feature a Sintered Bronze Element Which Provides Better Filtration and Does Not Require Replacement, Only Cleaning. All Filters are Equipped with a Press Type Manual Drain Which Incorporates the Night Time Drain Feature, Expelling Condensation When the Line Pressure Drops Below 11.6 psi. The Night Time Drain is Ideal for Applications Which Do Not Operate Continuously for Those Applications Which Do Operate Around the Clock We Recommend the Automatic Filter, Regulator & Lubricator Basics Compressed Air Systems Are Prone to Impurities and Dirt. Removing Dirt, Pipe Scale, Moisture, Rust, Compressor Oil and Other Contaminants Will Provide Longer Tool Life and Efficient Operation. Air Filters - Will Remove Foreign Particles (Up to 40 Micron) From the Air Stream and Should be Sized to Handle the Capacity of the Compressor. Optional 5 Micron Elements Are Available. Oil Coalescing Filters - Should Be Installed Downstream of the Air Filter to Ensure the Air is Completely Free of Oil, Water and Dirt. Coalescing Filters Feature a 0.01 Micron Element Which Will Remove 99.9% Of Water and Oil Droplets and Solids Larger than.3 Microns. Air Line Regulators - If the System Pressure is Greater Than Recommended, Excess Force (Torque and Wear) Can Shorten the Life of the Down Steam Devices and Waste Compressed Air. Air Line Regulators Provide Steady Outlet Pressure Regardless of Variations and Fluctuations, from the Inlet Pressure Extending Operation and Life of the Downstream Equipment. TECHNICAL DATA MCG SERIES Lubricators - The Air Line Lubricator is an Economical Way to Provide Lubrication Downstream. The Lubricator Stores Oil and Adds a Preset Amount Into the Air Stream Which is Delivered to the Downstream Tools and Devices. Combination Filter/Regulator - Space Saving Design Which Provides Both the Filter and Regulator in a One Piece Unit Reducing Installation Costs Air Line Filter Coalescing Filter Air Line Regulator Air Line Lubricator 19

20 Air Line Filters Used To Separate Dust, Dirt, Moisture and Other Contaminants From the Compressed Air Line Designed With a Separator & Shield for Efficient Moisture Separation Die Cast Aluminum Filter Head, Polycarbonate Bowl and Steel Bowl Guard Series 14, 15 and 17 Feature a Bayonet Bowl Guard 40 Micron Sintered Bronze Filter Element Standard Optional 5 Micron Element Available Press Type Manual Drain With Night Time Drain Feature Which Automatically Drains When the Pressure Drops Below 11.6 psi Maximum Pressure: 145 psig (10 bar) Ambient Temperature: 32 F F Optional Auto Drain Available MCGF13913-S 1/4 28 MCGF14913-S 1/4 49 MCGF14923-S 3/8 80 MCGF15933-S 1/2 125 MCGF17943-S 3/4 175 MCGF17953-S Coalescing Filters High Efficient Filtration (99.99%) Removing Fine Oil Particles and Droplets Up to 0.01 Micron Designed with a Separator & Shield for Efficient Moisture Separation Die Cast Aluminum Filter Head, Polycarbonate Bowl and Steel Bowl Guard Series 14, 15 and 17 Feature a Bayonet Bowl Guard High Performance Borosilicate Element Press Type Manual Drain With Night Time Drain Feature Which Automatically Drains When the Pressure Drops Below 11.6 psi Coalescing Filter Must Be Installed After a 5 Micron Filter Maximum Pressure: 145 psig (10 bar) Ambient Temperature: 32 F F Optional Auto Drain Available Part No. NPT In) SCFM MCGFS14912-S 1/4 28 MCGFS14922-S 3/8 32 MCGFS15932-S 1/2 48 MCGFS17942-S 3/4 71 MCGFS17952-S

21 Relieving Regulators Regulators Are Used to Maintain a Steady Outlet Pressure Unaffected By Fluctuations Aluminum Die Cast Designed with A Non Raising Press to Lock Adjusting Knob for Locking at Any Set Pressure Diaphragm Operated, Relieving Type Mechanism With Pressure Compensated by Balance Poppet Can Be Installed In Any Position Red Ring Provides Visual Check for Regulator in the Unlock Position Includes Panel Nut for Mounting Includes 2 Gauge Ports: 1/8 NPT (MCGR13, 14 & 15 Series), 1/4 (MCGR17 Series) Maximum Inlet Pressure: 220 psig (15 bar) Ambient Temperature: 32 F F Recommended PSB20-XXX Lubricators Used to Feed Lubricants to Pneumatic Equipment Maintains Constant Oil to Air Density Over a Wide Range of Flow Fog/Micro Mist Can Be Used Up to 50 Ft Pipe Runs Die Cast Aluminum Head, Polycarbonate Bowl With Steel Bowl Guard Series 14, 15 and 17 Feature a Bayonet Bowl Guard Head Is Fitted with Oil Drop Indicator, Oil Drop Controller & Oil Filling Plug Designed for Best Performance With 32 Grade Oil Maximum Pressure: 145 psig (10 bar) Ambient Temperature: 32 F F Spring Range MCGR13914C 1/4 21 MCGR14914C 1/4 56 MCGR14924C 3/8 88 MCGR15924C 3/ MCGR15934C 1/2 140 MCGR17944C 3/4 175 MCGR17954C TECHNICAL DATA MCG SERIES MCGL1391 1/4 48 MCGL1491 1/4 58 MCGL1492 3/8 106 MCGL1593 1/2 200 MCGL1794 3/4 255 MCGL

22 Combination Filters & Relieving Regulators Filter Used To Separate Dust, Dirt, Moisture and Other Contaminants From Compressed Air Designed with a Separator & Shield for Efficient Moisture Separation Die Cast Aluminum Filter Head, Polycarbonate Bowl With Steel Bowl Guard Series 14, 15, and 17 Feature a Bayonet Bowl 40 Micron Sintered Bronze Filter Element Standard Optional 5 Micron Element Available Press Type Manual Drain With Night Time Drain Feature Which Automatically Drains When the Pressure Drops Below 11.6 psi Maximum Pressure: 145 psig Relieving Regulator Regulators Are Used to Maintain a Steady Outlet Pressure Unaffected By Fluctuations Aluminum Die Cast Design with A Non Raising Press to Lock Adjusting Knob for Locking at Any Set Pressure Diaphragm Operated, Relieving Type Mechanism With Pressure Compensated by Balance Poppet Can Be Installed In Any Position Red Ring Provides Visual Check for Regulator in the Unlock Position Includes Panel Nut for Mounting Includes 2 Gauge Ports: 1/8 NPT (MCGR13, 14, & 15 Series), 1/4 (MCGR17 Series) Maximum Pressure: 145 psig (10 bar) Maximum Temperature: 140 F PSB20-XXX Part No. NPT (In) SCFM Bowl Size (Oz.) Pressure Range psi MCGFRC139134C-S 1/ MCGFRC149134C-S 1/ MCGFRC149234C-S 3/8 77 MCGFRC159334C-S 1/ MCGFRC179434C-S 3/ MCGFRC179534C-S