SECTION OUTDOOR SIGN WITH ELECTRONIC MESSAGE DISPLAY. A. Provisions of Division 01 apply to this section. 2. Section 02770: Site Concrete Work.

Size: px
Start display at page:

Download "SECTION OUTDOOR SIGN WITH ELECTRONIC MESSAGE DISPLAY. A. Provisions of Division 01 apply to this section. 2. Section 02770: Site Concrete Work."

Transcription

1 PART 1 - GENERAL 1.01 SUMMARY SECTION A. Provisions of Division 01 apply to this section. B. Section Includes: 1. Outdoor sign with electronic message display as indicated on the drawings. C. Related sections: 1. Section 02317: Excavation, backfilling and compacting for structures. 2. Section 02770: Site Concrete Work. 3. Section 05120: Structural steel. 4. Division 16: Electrical 1.02 REFERENCES A. Regulatory Requirements: 1. Design and fabrication shall conform to the requirements of CBC. B. Standards: 1. Sign shall be UL listed. 2. ASTM A36 Standard Specification for Carbon Structural Steel. 3. ASTM A123 Standard Specification for Zinc (Hot-Dip Galvanized) coatings on Iron and Steel Products. 4. ASTM A307 Standard Specifications for Carbon Steel Bolts (Ordinary Strength Bolts). 5. ASTM A500 Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Squares. 6. ASTM A529 Standard Specification for High-Strength Carbon-Manganese Steel of Structural Quality. 7. ASTM A572 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel. 8. AWSD1.1, Structural Welding Code-Steel. SCHOOL NAME

2 9. ASTM F1554 Standard Specification for anchor bolts, steel 36, 55 and 105 ksi yield strength DESIGN REQUIREMENTS A. It is manufacturer s responsibility to design, engineer and provide all required documentations to LAUSD for submittal to DSA. Manufacturer is responsible for any corrections required by DSA. 1. Support structure and anchorage as required. 2. Sign shall be engineered to withstand wind load requirement set by the code. 3. Sign, support structure and associated foundations shall be designed by a registered structural engineer licensed in the state of California SUBMITTALS A. Detailed plans, specifications and engineering calculations for submittal to DSA. B. Product Data: Submit manufacturer s catalogue cuts, product literature, material descriptions, finishes and color charts for each type of components. C. Shop Drawings: Submit Shop Drawings indicating sign style, lettering, and overall dimensions and qualities. D. Material Samples: Submit three samples each type, style and color of specified material. E. Closeout submittals: 1. Provide three (3) copies of programming and operating system manuals. 2. Provide three (3) copies of routine maintenance manuals QUALITY ASSURANCE A. Qualification of Manufacturer: Sign manufacturer shall have been regularly engaged in manufacturing this type of sign specified for at least 5 years. B. Design, fabricate, and install steel members in accordance with AISC Design, Fabrication, and Erection of Structural Steel for Buildings. C. AWS D-1.1 Codes Welding in Building Construction. Welders shall be AWS certified. D. Inspection of Welding: refer to Section Testing and Inspection. E. Source Quality Control: Mill Test Certification SCHOOL NAME

3 F. Work shall conform to California Code of Regulations (CCR), CBC and CAL/OSHA Regulations DELIVERY, STORAGE AND HANDLING A. Deliver products to site and protect from damage. Store until immediately prior to installation WARRANTY A. Manufacturer shall provide a 5 year written warranty for material and installation of the identification display sign cabinet and faces. B. Manufacturer shall provide a 5 year written warranty for material and installation of ballasts, lamp sockets and photo electric cells. C. Manufacturer shall provide 5 year written warranty for material and installation of electronic message display cabinet. D. Manufacturer shall provide a 5 year written warranty for material and installation of LED electrical message center. E. Manufacturer shall provide a 5 year written warranty that sign faces will not yellow or turn cloudy. PART 2 PRODUCTS NOTE TO SPECIFIER: Select applicable signs to fit site specific requirement. Provide elevations/details and graphics for each sign type and show locations of sign on plans. Check local ordinances and their requirements for sign square feet area, height restrictions, set back, minimum distance from the roadway and sidewalk, illumination restrictions and design the sign accordingly. Provide a 3 reveal between the two signs GENERAL REQUIREMENTS A. One wall mounted outdoor identification display sign with outdoor high definition LED electronic and programmable message display as specified below with complete control system software, wireless transmitter and receivers. Or A. One double-sided monument type with outdoor identification display sign and outdoor high definition LED electronic and programmable message display as specified below with complete control system software, wireless transmitter and receiver IDENTIFICATION DISPLAY SIGN A. Cabinet SCHOOL NAME

4 1. Size shall be 2-6 high x 8-0 wide x 10 thick. 2. Extruded aluminum. 3. Heli-arc welded at reinforced mitered corners. 4. Powder coated UV resistant paint finish. B. Lighting C. Faces 1. Internal illumination shall be achieved with high output instant start zero degree fluorescent lamps and ballast. 1. Sign faces:.118 thick unbreakable lexan 2. Graphics: 3M high performance pressure sensitive vinyl. 3. Graphics: shall include the name of the school and school s mascot based on school colors. Graphics shall be provided by the school or as indicated on the drawings. 4. Translucent colors: 3M high performance pressure sensitive vinyl. 5. Faces installation: vandal resistant ELECTRONIC MESSAGE DISPLAY A. Cabinet 1. Size: 2-6 high x 8-0 wide 2. Formed and welded weather proof aluminum cabinet 3. Cabinet shall be NEMA 4X rating 4. Thermostatically controlled fans shall automatically cool and warm the display 5. All electrical components shall be labeled for easy service B. Message Display 1. Double sided and high definition degree viewing angle SCHOOL NAME

5 3. 32x128 pixels mounted on circuit boards, 256 shaded matrix configuration. Each pixel shall be red light emitting diodes (LED) on.6 pitch high definition, I LED per pixel. Each LED to produce 6000 to nits 4. Display should be capable of displaying various text sizes as follow: a. 4 lines of 4.5 text, 21 characters wide. b. 3 lines variable 7, 13 characters wide. c. 2 lines of 10, 10 characters wide d. One line variable text. e. Graphics either by themselves or in conjunction with text. f. 100% solid-state electronic operating circuitry. g. Fast display speed to create smooth motion at 60 frames per second. 5. Front accessible for service. 6. RF Wireless communication system with a 4000 feet line of sight with the signal.to go through walls, trees and be completely WEP Encrypted to avoid hacking. Provide all required components required to make the system operational. 7. Matrix shall utilize a modular construction and each module shall conform to a 16 pixel wide configuration (high definition). 8. The electronic message center shall be covered by a specially designed cover like GE Lexan or equal. 9. CPU shall incorporate an optical isolator. 10. Unit shall include a lockable, weatherproof, direct connection communication port accessible from ground level without the need for a ladder or platform. C. Control Equipment: Sign shall be equipped with the control software necessary to program messages. The contractor shall load the software on a District supplied computer and provide an original hard copy of the control software as part of the close out package. D. Software requirements features 1. Scheduling in 12 or 24 hour format. 2. Scheduling system to allow for scheduling over 12 months. 3. Extensive help screens with excerpts from the operator s manual. SCHOOL NAME

6 4. Library functions for saving messages, animations and graphics to disk. 5. Twenty on and off modes for easy message creations. Five speed for each mode. 6. Automatic text formatting. 7. Text and graphics to be added to the same frame. 8. Animated graphic capability that runs 3-5 second AVI files video on 256 shaded models. 9. Animated graphics as well as variety of font styles and sizes. 10. Message compression for transmission to the sign. Accurate what you see is what you get display graphics to ensure what is seen on the computer screen is what you see on the sign 11. Menu-guided control 12. Supports optional input devices such as a mouse 13. Simultaneous display and edit capability 14. Automatic rebooting of system disk is made after power outage 15. Password protection capability 16. The system software, program sequences and schedules can be stored on a disk. 17. Uses graphics from widows software 18. Menu guided control of all software features 19 Interface with scanners, modems, etc. 20. Message display to hold memory minimum up to 60 days without power E. Electrical system requirements: volts, single phase, 20 amp circuit. 2. Sign shall be equipped with internally mounted line voltage surge suppressor and disconnecting means. 3. Sign parts likely to be energized shall be grounded per CEC requirements METAL FINISHES SCHOOL NAME

7 A. General: Comply with NAAMM s Metal Finishes Manual for Architectural and Metal Products for recommendations for applying and designating finishes CONCRETE A. 28 day compressive strength of 3000 psi minimum. Refer to section PART 3 - EXECUTION 3.01 EXAMINATION A. Verify the location of the sign and notify the owner of any conflict prior to start of work. B. Beginning of installation means installer accepts existing surfaces. C. Install in accordance with approved Shop Drawings and manufacturer s written recommendations. D. Bolt base plate to foundation, bearing on high-strength grout, unless otherwise detailed. E. Verify that the concrete foundations have reached the design strength prior to erection of steel. F. Coordinate the location of controller with OAR or as indicated on the drawings METHODS OF INSTALLATION A. Wall mounted Signs: 1. Verify the structural integrity of the wall and if there is any problem with support of the sign or means of attachment, notify the owner. 2. Attachment shall be tamper proof. B. Exterior Post Mounted Signs 1 It shall be installed per manufacturer s recommendations and approved shop drawings by DSA. C. Repair any damaged wall, sidewalk, landscaping to match adjacent area. D. Install electrical conduit, pull box and wiring to power source as indicated on the drawings TOLERANCES SCHOOL NAME

8 A. Signs shall be true and plumb after installation FIELD INSPECTIONS AND TESTS A. Inspections: Inspect equipment, signs, materials and installation for compliance with the applicable standards. B. Tests: Before Substantial Completion, perform operational tests to verify components including the actual sign, hardware and software. Test electrical connections and low voltage connection TRAINING A. Provide a trained technician on site for 4 hours to train the school s staff in the programming of the sign. The technician must be completely familiar with the system construction, assembly and testing of the equipment. The technician will set up the operating system, test and make the control system operational as well as the display system while on site. In addition, the technician shall go over maintenance requirements and replacement parts with M & O representatives. Allow minimum of 4 hours review with M & O CLEANUP A. Remove rubbish, debris, and waste materials and legally dispose of off Project site PROTECTION A. Protect Work of this section until Substantial Completion. END OF SECTION SCHOOL NAME

SECTION METAL STAIRS, LADDERS, AND WALKWAYS

SECTION METAL STAIRS, LADDERS, AND WALKWAYS SECTION 05510 METAL STAIRS, LADDERS, AND WALKWAYS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: Technical requirements for metal stairs, ladder, and walkways. 1.2 REFERENCES A. General: References to

More information

SECTION 32 31 13 CHAIN LINK FENCES AND GATES

SECTION 32 31 13 CHAIN LINK FENCES AND GATES SECTION 32 31 13 CHAIN LINK FENCES AND GATES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Fence framework, fabric, and accessories. 2. Excavation for post bases. 3. Concrete foundation for posts

More information

The City of Winnipeg Section Turtle Island Community Centre Renovation Page 1 of 5

The City of Winnipeg Section Turtle Island Community Centre Renovation Page 1 of 5 Turtle Island Community Centre Renovation Page 1 of 5 Part 1 General 1.1 SECTION INCLUDES.1 Shop fabricated ferrous metal items..2 Shop fabricated aluminum items..3 Steel pipe handrails balusters, and

More information

DENVER MODEL 30 X 30 SPECIFICATIONS

DENVER MODEL 30 X 30 SPECIFICATIONS DENVER MODEL 30 X 30 SPECIFICATIONS Dimensions: Roof Dimensions 30-0 x 30-0 (4) Columns (Center to Center) 25-6½ x 25-6½ Minimum Clearance 8-0 Roof Height @ Peak Dependent on Col. Ht. Hip Roof 4:12 pitch

More information

SECTION 03400 PRECAST CONCRETE STRUCTURES

SECTION 03400 PRECAST CONCRETE STRUCTURES SECTION 03400 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for precast concrete structures, including fabrication and erection. 1.02 REFERENCE STANDARDS A. American Society for

More information

COLORADO MODEL. 35 x 65 SPECIFICATIONS

COLORADO MODEL. 35 x 65 SPECIFICATIONS COLORADO MODEL 35 x 65 SPECIFICATIONS Dimensions: Roof Dimensions 35-0 x 65-0 Column Dimensions (center to center) 31-0 x 30-6 Minimum Clearance 14-0 Roof Height @ Peak ±18-8 Curved Roof ±42-6 radius Square

More information

A. The shade structure contractor shall be responsible for the design, engineering, fabrication, and supply of the work specified herein.

A. The shade structure contractor shall be responsible for the design, engineering, fabrication, and supply of the work specified herein. 13310 FABRIC SHADE STRUCTURES FOR PLAYGROUND AREAS ************************************************************************************************************************ SPECIFIER: CSI Master Format

More information

SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS

SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word

More information

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 08332 COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Counter Fire Doors. 1.2

More information

CAGED ALUMINUM ACCESS LADDERS

CAGED ALUMINUM ACCESS LADDERS SECTION 05512 CAGED ALUMINUM ACCESS LADDERS ***** UPNO VR, Inc. manufactures several types of aluminum access ladders. This guide specification section can be used to specify fixed, wall mounted, vertical

More information

2. Division 05 Structural Steel Framing for steel framework requirements

2. Division 05 Structural Steel Framing for steel framework requirements SECTION 131200 - CLIMBING WALLS PART 1 GENERAL 1.1 SUMMARY A. This section includes the following: 1. GFRC Rock Realistic Climbing Wall System B. Related Sections 1. Division 04 Unit Masonry 2. Division

More information

SECTION 11014 WINDOW WASHING SYSTEMS

SECTION 11014 WINDOW WASHING SYSTEMS SECTION 11014 WINDOW WASHING SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section includes, but is not limited to, design and furnishing portable davits, davit sleeves, dvit bases, four (4) removable outriggers,

More information

SPECIFICATIONS Rev:

SPECIFICATIONS Rev: SPECIFICATIONS Rev: 060209 Section Helical Steel Piles 1. General 1.1. Description 1.1.1. The work of this section consists of furnishing and installing steel helical piles manufactured by MacLean-Dixie

More information

1.02 SYSTEM DESCRIPTION

1.02 SYSTEM DESCRIPTION 1 OF 7 MODULAR MEZZANINES GUIDE SPECIFICATIONS FOR PART 1 - GENERAL 1.01 RELATED WORK A. SECTION 03 30 00: Cast in Place Concrete (and Concrete Finishing) 1. The area where mezzanine is installed shall

More information

SECTION METAL BUILDING SYSTEMS. A. Metal wall and roof panels including gutters and downspouts.

SECTION METAL BUILDING SYSTEMS. A. Metal wall and roof panels including gutters and downspouts. New Football Stadium 13.34.19-1 PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 13.34.19 METAL BUILDING SYSTEMS A. Metal wall and roof panels including gutters and downspouts. 1.02 RELATED REQUIREMENTS A.

More information

SECTION 02824 EXPANDED METAL MESH FENCE

SECTION 02824 EXPANDED METAL MESH FENCE SECTION 02824 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for expanded metal mesh fence on the right-of-way. 1.02 REFERENCE STANDARDS A. ASTM International (ASTM): 1.03 SUBMITTALS

More information

Sports and High Mast Lighting Poles Phone: (866) 474-7200 Fax: (817) 924-7049

Sports and High Mast Lighting Poles Phone: (866) 474-7200 Fax: (817) 924-7049 Sports and High Mast Lighting Poles 4 High Mast Lighting Poles General American LitePole offers a raising and lowering system that allows for ease of maintaining the lighting system at ground level. Ideal

More information

HIGH TENSION CABLE BARRIER

HIGH TENSION CABLE BARRIER Special Provision September 11, 2006 SECTION 02845 S HIGH TENSION CABLE BARRIER PART 1 GENERAL 1.1 SECTION INCLUDES A. Cable barrier materials and installation procedures. 1.2 RELATED SECTIONS A. Section

More information

Product Specification instalert Rapid Messenger Variable Message Sign

Product Specification instalert Rapid Messenger Variable Message Sign instalert 2 units to cover any application instalert 18 (ia18): 18 x 28 full matrix instalert 24: (ia24): 24 x 60 full matrix Size, Weight without battery ia18: 30 x 20 x 2.74, 29 lbs ia24: Folds to fits

More information

SECTION 1 GENERAL REQUIREMENTS

SECTION 1 GENERAL REQUIREMENTS Page 1 of 6 SECTION 1 GENERAL REQUIREMENTS 1. SCOPE OF WORK: The work to be performed under the provisions of these documents and the contract based thereon includes furnishing all labor, equipment, materials,

More information

SECTION 63 CHAIN-LINK FENCES (FAA F-162) ITEM F-162 CHAIN-LINK FENCES DESCRIPTION MATERIALS

SECTION 63 CHAIN-LINK FENCES (FAA F-162) ITEM F-162 CHAIN-LINK FENCES DESCRIPTION MATERIALS SECTION 63 CHAIN-LINK FENCES (FAA F-162) 63-1 GENERAL This specification covers the furnishing and installation of chain link fencing and gates, both permanent and temporary, at the locations shown on

More information

Preformed Metal Roofing and Siding

Preformed Metal Roofing and Siding Page -1-1. GENERAL 1.1. Description This specification along with the drawings covers the furnishing of all material, products, equipment, accessories, tools, services, transportation, labor and supervision

More information

SECTION HOLLOW METAL DOORS AND FRAMES

SECTION HOLLOW METAL DOORS AND FRAMES New Football Stadium 08.11.13-1 SECTION 08.11.13 HOLLOW METAL DOORS AND FRAMES PART 1 GENERAL 1.01 SECTION INCLUDES A. Non-fire-rated hollow metal doors and frames. B. Hollow metal frames for wood doors.

More information

SECTION STRUCTURAL STEEL

SECTION STRUCTURAL STEEL SECTION 05200 PART 1 GENERAL 1.01 DESCRIPTION A. Section includes specifications for structural steel, including steel designated as structural steel on the Contract Drawings. 1.02 REFERENCE STANDARDS

More information

ARCHITECTURAL SPECIFICATIONS RHINO ADO 7000

ARCHITECTURAL SPECIFICATIONS RHINO ADO 7000 ARCHITECTURAL SPECIFICATIONS RHINO ADO 7000 LOW-ENERGY ELECTRIC SWING DOOR OPERATOR PART I - GENERAL 1.01 SUMMARY A. SECTION INCLUDES: Access Automation s low energy swing door operator. 1.02 REFERENCES

More information

SECTION RESIDENTIAL OVERHEAD DOORS TRADITIONAL STEEL COLLECTION INSULATED DOORS SERIES

SECTION RESIDENTIAL OVERHEAD DOORS TRADITIONAL STEEL COLLECTION INSULATED DOORS SERIES SECTION 08361 RESIDENTIAL OVERHEAD DOORS TRADITIONAL STEEL COLLECTION INSULATED DOORS - 390 SERIES Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of

More information

LEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code

LEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code LEGACY REPORT Reissued November 1, 2003 ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California 90601 # (562) 699-0543 Regional Office # 900

More information

The Kodiak 2400 Seating System by Royal Stewart Ltd.:

The Kodiak 2400 Seating System by Royal Stewart Ltd.: The Kodiak 2400 Seating System by Royal Stewart Ltd.: PART 1 GENERAL 1.1 Description Telescopic Bleacher Seating includes either manually or electrically operated systems of multiple tiered seating rows

More information

ATLANTA MODEL SPECIFICATIONS

ATLANTA MODEL SPECIFICATIONS ATLANTA MODEL 50 SPECIFICATIONS Dimensions: Roof Dimensions (point to point) 50-0 Column Dimensions (out to out of columns) 44-0 Eave Height 8-0 Roof Height @ Peak ±21-8⅞ Hip Roof 6:12 pitch Square Feet

More information

Light Gauge Metal Trusses Specification Architectural Guide Specification

Light Gauge Metal Trusses Specification Architectural Guide Specification Precision Walls, Inc. 1230 NE Maynard Rd. Cary, NC 27513 Light Gauge Metal Trusses Specification Architectural Guide Specification PART 1: GENERAL * Instructions, options and comments for the specification

More information

ST. PETERSBURG NATIONAL GUARD SECTION 11132

ST. PETERSBURG NATIONAL GUARD SECTION 11132 PART 1 GENERAL 1.01 SUMMARY A. Section Includes: This Section specifies electrically operated front projection screens and ac cessories. 1.02 RELATED SECTIONS A. Div 16 Electrical Common Work Results for

More information

1. Section "Architecturally Exposed Structural Steel Framing" for additional requirements for architecturally exposed structural steel.

1. Section Architecturally Exposed Structural Steel Framing for additional requirements for architecturally exposed structural steel. SECTION 051200 - PART 1 - GENERAL 1.1 SUMMARY A. Section includes structural steel and grout. B. Related Sections: 1. Section 051213 "Architecturally Exposed Structural Steel Framing" for additional requirements

More information

Suggested Specification for Hot-Dip Galvanizing Revised May 2002

Suggested Specification for Hot-Dip Galvanizing Revised May 2002 Suggested Specification for Hot-Dip Galvanizing Revised May 2002 This suggested specification is provided as a guide to producing a quality document calling for after-fabrication hot-dip galvanizing of

More information

C. Samples for Initial Selection: For each type of fire protection cabinet indicated.

C. Samples for Initial Selection: For each type of fire protection cabinet indicated. SECTION 10 44 13 - FIRE EXTINGUISHER CABINETS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Fire protection cabinets for the following: a. Portable fire extinguishers. NOTE: Indicate on the drawings

More information

PART 1 GENERAL 1.1 SECTION INCLUDES

PART 1 GENERAL 1.1 SECTION INCLUDES J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including

More information

SECTION [SECTION 10705] EXTERIOR SUN CONTROL DEVICES

SECTION [SECTION 10705] EXTERIOR SUN CONTROL DEVICES SECTION 10 71 13 [SECTION 10705] EXTERIOR SUN CONTROL DEVICES Specifier's note: Use this Section when specifying vertical or horizontal Sun Control Devices fabricated from aluminum extrusions, such as,

More information

Generic Technical Performance Specification GTS-1653 February 2001 Issue: 01 Revision: 00 Page 1 of 5

Generic Technical Performance Specification GTS-1653 February 2001 Issue: 01 Revision: 00 Page 1 of 5 Issue: 01 Revision: 00 Page 1 of 5 1 ASSEMBLY - GENERAL 1.1 The work of this section includes the provision of all design, labour, materials, equipment and services required to fabricate and install stair

More information

Standing Seam Spec Option BIPV Section 07400

Standing Seam Spec Option BIPV Section 07400 Standing Seam Spec Option BIPV Section 07400 A. Standing Seam Metal Roof Manufacturer and Contractor shall be responsible for manufacturing and installing BIPV Standing Seam Roof Panel per drawings for

More information

V. GUIDE SPECIFICATIONS

V. GUIDE SPECIFICATIONS V. GUIDE SPECIFICATIONS This Guide Specification is intended to be used for the development of an office master specification or in the preparation of specifications for a particular project. In either

More information

Low Bay LED Light - 250W Metal Halide Equivalent - 12 LEDs - 40 Watt High Output LEDs

Low Bay LED Light - 250W Metal Halide Equivalent - 12 LEDs - 40 Watt High Output LEDs Low Bay LED Light - 250W Metal Halide Equivalent - 12 LEDs - 40 Watt High Output LEDs Part #: GAU-LB-400 Page: 1 Made in USA Compliant The GAU-LB-400 LED Low Bay Light offers high light output from a compact

More information

1. Division-5 Section Metal Fabrications for material and welding requirements related to wrought iron fencing.

1. Division-5 Section Metal Fabrications for material and welding requirements related to wrought iron fencing. SECTION 02835 SITE FENCES AND GATES PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

specifications A*COM SYSTEM bridging the gap. A*COM Commercial Ramp System PART 1 General

specifications A*COM SYSTEM bridging the gap.  A*COM Commercial Ramp System PART 1 General specifications A*COM Commercial Ramp System This section is based on products manufactured by A*COM and distributed by AlumiRamp, Inc., located at the following address: 855 Chicago Road, Quincy, MI 49082,

More information

MATERIAL SPECIFICATIONS

MATERIAL SPECIFICATIONS FENCING - 1 2-11-1 CHAIN LINK FENCE AND GATE(S) A. SCOPE MATERIAL SPECIFICATIONS This section covers the work necessary for the chain link fence gate(s), complete. General Like items of materials provided

More information

A. Extent of steel joists is shown on drawings, including basic layout and type of joists required.

A. Extent of steel joists is shown on drawings, including basic layout and type of joists required. SECTION 05 21 00- STEEL JOIST FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-01 Specification

More information

C. ANSI C Electrical Analog Indicating Instruments. E. ANSI C Guide for Transformer through Fault Duration.

C. ANSI C Electrical Analog Indicating Instruments. E. ANSI C Guide for Transformer through Fault Duration. SECTION 264260 - DISTRIBUTION SWITCHBOARDS PART 1 GENERAL 1.01 SECTION INCLUDES A. Main switchboard. 1.03 RELATED SECTIONS A. Drawings and general provisions of the Contract, including General and Supplementary

More information

SECTION 02832 CHAIN LINK FENCE AND GATES

SECTION 02832 CHAIN LINK FENCE AND GATES SECTION 02832 CHAIN LINK FENCE AND GATES PART 1 GENERAL 1.01 SECTION INCLUDES A. Fabrication, furnishing and installation of chain link fence, chain link gates, and extension brackets with barbed wire.

More information

The Manitoba Water Services Board SECTION 027110 Standard Construction Specifications September 2013 Page 1 of 12

The Manitoba Water Services Board SECTION 027110 Standard Construction Specifications September 2013 Page 1 of 12 September 2013 Page 1 of 12 Part 1 General 1.1 DESCRIPTION OF WORK.1 The work shall consist of the supply and construction of a chain link fence, barb wire fences or mesh fences as shown on the Plans or

More information

SECTION 16542 EXTERIOR/SECURITY L.E.D. LIGHTING

SECTION 16542 EXTERIOR/SECURITY L.E.D. LIGHTING SECTION 16542 EXTERIOR/SECURITY L.E.D. LIGHTING PART 1 - GENERAL 1.01 REQUIREMENTS A. The general provisions of the Contract, including General and Supplementary Conditions and General Requirements, apply

More information

FEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST, METAL (CHAIN-LINK FENCE POSTS, TOP RAILS AND BRACES)

FEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST, METAL (CHAIN-LINK FENCE POSTS, TOP RAILS AND BRACES) INCH-POUND RR-F-191/3E AMENDMENT 1 29 OCTOBER 2007 FEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST, METAL (CHAIN-LINK FENCE POSTS, TOP RAILS AND BRACES) The General Services Administration has authorized

More information

LIGHTING EQUIPMENT Belleville Fire Hall/Headquarters and Emergency Operations Centre Section Belleville, Ontario Page 1 of 6

LIGHTING EQUIPMENT Belleville Fire Hall/Headquarters and Emergency Operations Centre Section Belleville, Ontario Page 1 of 6 Belleville, Ontario Page 1 of 6 1 GENERAL 1.1 GENERAL REQUIREMENTS.1 The General Conditions of CCDC2-2008, and the General requirements of Division 1, form part of this Section and must read in conjunction

More information

SECTION 02630 STORM DRAINAGE SYSTEM

SECTION 02630 STORM DRAINAGE SYSTEM SECTION 02630 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for storm drainage systems including modifications and connections to existing storm drainage systems. 1.02 REFERENCE

More information

LOADING DOCK EQUIPMENT. A. Section 03100 - Concrete Forms and Accessories: Placement of anchors into concrete.

LOADING DOCK EQUIPMENT. A. Section 03100 - Concrete Forms and Accessories: Placement of anchors into concrete. LOADING DOCK EQUIPMENT PART 1 GENERAL 1.1 SECTION INCLUDES A. Loading dock equipment of the following types: 1. Dock lifts. 2. Control stations. 1.2 RELATED SECTIONS A. Section 03100 - Concrete Forms and

More information

3. Listed [grease] [dishwasher] [grease and dishwasher] ducts.

3. Listed [grease] [dishwasher] [grease and dishwasher] ducts. SECTION 23 51 00 BREECHINGS, CHIMNEYS, AND STACKS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION 02200 SUPPORT OF EXCAVATION

SECTION 02200 SUPPORT OF EXCAVATION SECTION 02200 PART 1 GENERAL 1.01 DESCRIPTION A. Section including specifications for design and installation of excavation support. B. Section also includes specifications for excavation support systems

More information

SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS. System 402 Flush-Glazed Screw Spline Storefront

SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS. System 402 Flush-Glazed Screw Spline Storefront PART 1 GENERAL 1.01 Work Included SECTION 08 41 1 ALUMINUM FRAMED ENTRANCES and STOREFRONTS System 402 Flush-Glazed Screw Spline Storefront A. Furnish and install aluminum architectural storefront system

More information

A. Project Altitude: Base air ratings on actual site elevations.

A. Project Altitude: Base air ratings on actual site elevations. SECTION 233416 CENTRIFUGAL HVAC FANS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Area Lighting Poles Phone: (866) Fax: (817)

Area Lighting Poles Phone: (866) Fax: (817) Area Lighting s 10 Area Lighting s Design The selection of the correct pole design is predicated on the specifi c loading requirements of each application. The poles located in the steel pole chart are

More information

Section Fiberglass Reinforced Plastic Grating and Structural Fabrications

Section Fiberglass Reinforced Plastic Grating and Structural Fabrications Section 06600 Fiberglass Reinforced Plastic Grating and Structural Fabrications Part 1. General 1.01 Related documents: A. Contract drawings, including general drawings and addenda drawings. B. General

More information

SECTION 07720 PREFORMED METAL STANDING SEAM ROOFING

SECTION 07720 PREFORMED METAL STANDING SEAM ROOFING SECTION 07720 PREFORMED METAL STANDING SEAM ROOFING PART ONE GENERAL DESCRIPTION This section includes pre-formed standing seam metal roofing and related flashings, closures, trim and accessories including,

More information

Section Fiberglass Reinforced Plastic Grating and Structural Fabrications

Section Fiberglass Reinforced Plastic Grating and Structural Fabrications Section 06600 Fiberglass Reinforced Plastic Grating and Structural Fabrications Part 1. General 1.01 Related documents: A. Contract drawings, including general drawings and addenda drawings. B. General

More information

SECTION 33 41 13 PUBLIC STORM UTILITY DRAINAGE PIPING

SECTION 33 41 13 PUBLIC STORM UTILITY DRAINAGE PIPING SECTION 33 41 13 PUBLIC STORM PART 1 - GENERAL 1.01 SECTION INCLUDES A. Storm drainage piping, fittings, and accessories at proposed station areas and locations other than under and immediately adjacent

More information

FACTORY POWDER COATED BOLTED STEEL TANK

FACTORY POWDER COATED BOLTED STEEL TANK 214100 FACTORY POWDER COATED BOLTED STEEL TANK PART 1 GENERAL 1.01 SCOPE A. This specification covers the furnishing of all labor, material, equipment, tools, services and erection of a Factory Powder

More information

LOS ANGELES UNIFIED SCHOOL DISTRICT Policy Bulletin

LOS ANGELES UNIFIED SCHOOL DISTRICT Policy Bulletin TITLE: NUMBER: School Marquee (Outdoor Sign with Electronic Message Display) ROUTING All Schools and Offices ISSUER: DATE: May 25, 2010 James Morris, Chief Operating Officer Office of the Chief Operating

More information

SECTION CHALKBOARDS AND MARKERBOARDS

SECTION CHALKBOARDS AND MARKERBOARDS PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 11 13 CHALKBOARDS AND MARKERBOARDS SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable

More information

Solar Panel Installations

Solar Panel Installations Solar Panel Installations Page 1 of 6 SINGLE-FAMILY RESIDENTIAL CHECKLIST City of Hayward Development Services Department Revised: 7-09-15 PERMIT REQUIREMENTS Permits are required for all solar panel installations.

More information

ELECTRICAL CONTRACTORS THE UNIVERSITY OF TENNESSEE KNOXVILLE, TENNESSEE SECTION 16050 PAGE 1

ELECTRICAL CONTRACTORS THE UNIVERSITY OF TENNESSEE KNOXVILLE, TENNESSEE SECTION 16050 PAGE 1 KNOXVILLE, TENNESSEE SECTION 16050 PAGE 1 PART 1 - GENERAL 1.01 RELATED DOCUMENTS: SECTION 16050 A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1

More information

SECTION A. General Conditions, Supplementary Conditions and Division 1 General Requirements apply to Work of this Section.

SECTION A. General Conditions, Supplementary Conditions and Division 1 General Requirements apply to Work of this Section. SECTION 03450 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. General Conditions, Supplementary Conditions and Division 1 General Requirements apply to Work of this Section. 1.2 SUMMARY A. Section includes: Provide

More information

SECTION OUTLET, JUNCTION, AND PULL BOXES

SECTION OUTLET, JUNCTION, AND PULL BOXES SECTION 16135 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes requirements for outlet boxes for use with wiring devices and lighting fixture outlets. 1.02 REFERENCE STANDARDS A. California Code of

More information

City of San Diego, CWP Guidelines

City of San Diego, CWP Guidelines PART 1 -- GENERAL SECTION 08520-1.1 WORK OF THIS SECTION City of San Diego, CWP Guidelines A. The WORK of this Section includes providing aluminum windows with frames, bracing, glazing attachments, screens,

More information

SECTION HVAC Fans

SECTION HVAC Fans SECTION 23 34 00 PART 1 GENERAL 1.1 SUMMARY A. Section Includes 1. The ceiling-mounted circulation fan is the model scheduled with the capacities indicated. The fan shall be furnished with standard mounting

More information

A. This Section includes wood roof, and floor trusses and truss accessories.

A. This Section includes wood roof, and floor trusses and truss accessories. SECTION 06176 - METAL-PLATE-CONNECTED WOOD TRUSSES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION 23 81 43 HEAT PUMPS

SECTION 23 81 43 HEAT PUMPS SECTION 23 81 43 HEAT PUMPS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Packaged rooftop heat pumps. 1.2 REFERENCES A. American Society of Heating, Refrigerating and Air-Conditioning Engineers:

More information

Project Specifications For Prefabricated Steel Truss Bridge

Project Specifications For Prefabricated Steel Truss Bridge Project Specifications For Prefabricated Steel Truss Bridge General: These specifications are for a fully engineered clear span bridge of welded steel construction and shall be regarded as minimum standards

More information

SECTION REINFORCING STEEL. 1. Section , Structural Concrete.

SECTION REINFORCING STEEL. 1. Section , Structural Concrete. SECTION 03 21 00 REINFORCING STEEL PART 1 GENERAL 1.01 SECTION INCLUDES A. This WORK shall consist of furnishing and placing reinforcing steel in accordance with these SPECIFICATIONS and in conformity

More information

B. Related Sections: 1. Section 26 05 33 - Raceway and Boxes for Electrical Systems.

B. Related Sections: 1. Section 26 05 33 - Raceway and Boxes for Electrical Systems. SECTION 262726 - WIRING DEVICES PART 1 - GENERAL 1.1 SUMMARY A. Section includes wall switches; wall dimmers; receptacles; multioutlet assembly; and device plates and decorative box covers. B. Related

More information

Inmate Security Transport Vehicle (ISTV) Bid Specifications

Inmate Security Transport Vehicle (ISTV) Bid Specifications Inmate Security Transport Vehicle (ISTV) Bid Specifications 1.0 INTRODUCTION This specification describes the caging requirements for a 12-Passenger Van (Make/Model: 2013 Chevrolet Express C2500) to be

More information

Statement of Special Inspections, 2013 CBC

Statement of Special Inspections, 2013 CBC BUILDING AND SAFETY DEPARTMENT Statement of Special Inspections, 2013 CBC PROJECT ADDRESS PERMIT NUMBER # Description of Work: This Statement of Special Inspections is submitted in fulfillment of the requirements

More information

1. Galvanized fence framework, fabric, and accessories. 2. Excavation for post bases, and concrete for post footings.

1. Galvanized fence framework, fabric, and accessories. 2. Excavation for post bases, and concrete for post footings. SECTION 32 31 13 CHAIN LINK FENCES PART 1 GENERAL 1.1 SUMMARY A. This Section includes: 1. Galvanized fence framework, fabric, and accessories. 2. Excavation for post bases, and concrete for post footings.

More information

These specifications shall apply to all high strength bolts and anchor bolts.

These specifications shall apply to all high strength bolts and anchor bolts. BOLTS (New Section) 972 972.1 REQUIREMENTS These specifications shall apply to all high strength bolts and anchor bolts. 972.2 SPECIFIC REQUIREMENTS A. General: All bolts, nuts, and washers shall have

More information

ADDENDUM #1(BID PACKAGE # 3)

ADDENDUM #1(BID PACKAGE # 3) H2Engineering, Inc. 114 East Fifth Avenue Tallahassee, FL 32303 Phone 850.224.7922 Fax 850.224.5876 ADDENDUM #1(BID PACKAGE # 3) To: Jeff Williams From: Peter Lindstrom Co: Leon County Date: October 04,

More information

SHELVING SHELVING ACCESSORIES TROLLEYS HARDWARE BARWARE KITCHEN EQUIPMENT HOSPITALITY FURNITURE.

SHELVING SHELVING ACCESSORIES TROLLEYS HARDWARE BARWARE KITCHEN EQUIPMENT HOSPITALITY FURNITURE. SHELVING ACCESSORIES TROLLEYS HARDWARE BARWARE KITCHEN EQUIPMENT HOSPITALITY FURNITURE M-SPAN Shelving The all new M-Span shelf is designed to be easy to clean and last a lifetime for an affordable price.

More information

- STRONGHOLD IRON FENCE PARTS AND MATERIALS SPECIFICATIONS -

- STRONGHOLD IRON FENCE PARTS AND MATERIALS SPECIFICATIONS - - STRONGHOLD IRON FENCE PARTS AND MATERIALS SPECIFICATIONS - PART 1.01: MATERIALS STEEL: All steel material for the fence and gate system shall conform to the requirements of ASTM A- 787 and ASTM A653

More information

SECTION ANCHOR BOLTS. A. Provide bolts and nuts that meet the standards given in Table 1.

SECTION ANCHOR BOLTS. A. Provide bolts and nuts that meet the standards given in Table 1. SECTION 16449 PART 1 DESCRIPTION A. Fabricate and install anchor bolts to be embedded in or attached to concrete. PART 2 MATERIALS 2.01 BOLTS AND NUTS A. Provide bolts and nuts that meet the standards

More information

CHAIN-LINK FENCES BID SPECIFICATIONS DESCRIPTION

CHAIN-LINK FENCES BID SPECIFICATIONS DESCRIPTION CHAIN-LINK FENCES BID SPECIFICATIONS DESCRIPTION 1 This item shall consist of furnishing and erecting Chain-Link fence in accordance with these specifications and the details shown on the plans and in

More information

FIRE ALARM AND DETECTION SYSTEMS SECTION 16721

FIRE ALARM AND DETECTION SYSTEMS SECTION 16721 PART 1 - GENERAL 1.01 WORK INCLUDED FIRE ALARM AND DETECTION SYSTEMS SECTION 16721 A. Provide a complete fully addressable, power limited, fire detection and evacuation system. The system shall be connected

More information

SPECIFICATIONS. DIVISION 7 Thermal and Moisture Protection. Section Architectural Metal Panels. CMPS AP SERIES ALUMINUM PANELS

SPECIFICATIONS. DIVISION 7 Thermal and Moisture Protection. Section Architectural Metal Panels. CMPS AP SERIES ALUMINUM PANELS SPECIFICATIONS DIVISION 7 Thermal and Moisture Protection. Section 07420 Architectural Metal Panels. CMPS AP SERIES ALUMINUM PANELS PART 1 GENERAL 1.1 RELATED WORK.1 Section 04220 Concrete unit masonry.2

More information

Residential Statement of Special Inspections**

Residential Statement of Special Inspections** Residential Statement of Special Inspections** CNI-033R Name of Owner Address Permit Number Job Description This Statement of Special Inspections is submitted to outline the requirements of 2013 CBC Chapter

More information

Originally Issued: 02/15/2011 Revised: 02/29/2016 Valid Through: 02/28/2017

Originally Issued: 02/15/2011 Revised: 02/29/2016 Valid Through: 02/28/2017 EVALUATION SUBJECT: ALUR WALL REPORT HOLDER: Modular Architectural Interiors 330 Waterloo Valley Road Mount Olive, NJ 07828 Phone: (973) 446-2300 Fax: (973) 446-2399 http://alurwalls.com/ CSI Division:

More information

SECTION EXTERIOR SUN SHADES

SECTION EXTERIOR SUN SHADES SECTION 10 71 13 EXTERIOR SUN SHADES USE THIS SECTION WHEN SPECIFYING C.R. LAURENCE CUSTOM FABRICATED SUN SHADE SYSTEMS. THE CRL CUSTOM FABRICATED SUN SHADE SYSTEMS ARE AVAILABLE IN MANY PROVEN DESIGNS,

More information

C. See Division 5 Section "Pipe and Tube Railings" for metal pipe and tube railings.

C. See Division 5 Section Pipe and Tube Railings for metal pipe and tube railings. SECTION 05 50 00 METAL FABRICATIONS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Miscellaneous steel framing and supports. 2. Metal ladders. 3. Shelf angles. 4. Loose bearing

More information

SECTION 164XX FUSED MAIN AND DISTRIBUTION SWITCHBOARDS

SECTION 164XX FUSED MAIN AND DISTRIBUTION SWITCHBOARDS SECTION 164XX FUSED MAIN AND DISTRIBUTION SWITCHBOARDS PART 1 GENERAL 1.1 SUMMARY A. Furnish and install main and distribution switchboards as shown on the drawings. Switchboard shall be free-standing,

More information

SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE

SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE SECTION 15076 CEMENT-MORTAR LINED AND COATED (CML&C) STEEL PIPE PART 1 GENERAL 1.01 DESCRIPTION This section designates the requirements for steel pipe fabrication, test in shop, installation of steel

More information

MODEL SPECIFICATIONS: Helical Pile Specifications

MODEL SPECIFICATIONS: Helical Pile Specifications MODEL SPECIFICATIONS: Helical Pile Specifications March/2015 v1.1 31 66 00 HELICAL PILE/ANCHOR DEEP FOUNDATIONS PART 1 GENERAL 1.01 SCOPE OF WORK The work shall consist of the Helical Pile Contractor furnishing

More information

SECTION PERFORMANCE SERIES 600 TVL DAY/NIGHT INDOOR/OUTDOOR VANDAL DOME IR CAMERA, HD70P

SECTION PERFORMANCE SERIES 600 TVL DAY/NIGHT INDOOR/OUTDOOR VANDAL DOME IR CAMERA, HD70P SECTION 282329 PERFORMANCE SERIES 600 TVL DAY/NIGHT INDOOR/OUTDOOR VANDAL DOME IR CAMERA, HD70P PART 1 GENERAL 1.1 SECTION INCLUDES A. Provide a 600 TVL day/night, indoor and outdoor, vandal-resistant,

More information

Display hidden notes to specifier. (Don't know how? Click Here) A. Advanced Upcoiling Security Grilles, power operated.

Display hidden notes to specifier. (Don't know how? Click Here) A. Advanced Upcoiling Security Grilles, power operated. SECTION 08333 ADVANCED UPCOILING SECURITY GRILLE MODEL 600 ADV Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Advanced Upcoiling Security Grilles,

More information

SECTION GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS

SECTION GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS SECTION 260526 - GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and

More information

AIRPORT SECURITY FENCING. A. American Society for Testing and Materials (ASTM):

AIRPORT SECURITY FENCING. A. American Society for Testing and Materials (ASTM): SECTION 02832 AIRPORT SECURITY FENCING PART 1-GENERAL 1.1 SUMMARY A. Section includes: Construct airport security chain-link fence and gate at specified areas and conforming lines, grades, details indicated

More information

SECTION HVAC Fans

SECTION HVAC Fans PART 1 GENERAL SECTION 23 34 00 1.1 SUMMARY A. Section Includes 1. The ceiling-mounted circulation fan is the model scheduled with the capacities indicated. The fan shall be furnished with mounting hardware

More information

.2 Section Waste Management and Disposal..4 Section Testing, Adjusting and Balancing (TAB) of Mechanical Systems.

.2 Section Waste Management and Disposal..4 Section Testing, Adjusting and Balancing (TAB) of Mechanical Systems. Issued 2006/08/01 Section 15072 Vibration Isolation Page 1 of 5 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01330 Submittal Procedures..2 Section 01355 Waste Management and Disposal.3 Section 03300 Cast

More information

SECTION 260536 - CABLE TRAYS. A. Continuous, rigid, welded steel or stainless steel wire mesh cable management system.

SECTION 260536 - CABLE TRAYS. A. Continuous, rigid, welded steel or stainless steel wire mesh cable management system. SECTION 260536 - CABLE TRAYS PART 1 - GENERAL SECTION INCLUDES: A. Continuous, rigid, welded steel or stainless steel wire mesh cable management system. B. Cable tray systems are defined to include, but

More information