Quincy QR-25. Series Model 340. Quincy. Compressor. Parts Manual Record of Change 106

Transcription

1 Quincy QR-5 Series Model 340 s Manual Record of Change 106 This manual contains important safety information and should be made available to all personnel who operate and/or maintain this product. Carefully read this manual before attempting to operate or perform maintenance on this compressor. Fill Out & Return Warranty Registration Card Located Inside Quincy Compressor True Blue Reliability TM Manual No October 001 Edition

2 INTRODUCTION This manual provides information for the following QR-5 Series, Model 340 (Record of Change 106) compressor versions: P PUL L S LS LVD Control Version P plain head assembly & no controls Control Version PUL plain head assembly with a pressure relief valve Control Version L head assembly with unloader towers & a hydraulic unloader Control Version S head assembly with unloader towers & a pilot valve Control Version LS head assembly with unloader towers, a hydraulic unloader, & a pilot valve with a check valve assembly Control Version LVD head assembly with unloader towers, a hydraulic unloader, & a pilot valve with a lockout & check valve These compressors are aircooled, two stage, two cylinder, pressure lubricated compressors, with up to 00 p.s.i. continuous pressure capability (01 to 500 p.s.i. intermittent pressure capability with proper configuration; consult factory). The Model 340 has a 5-1/4" low pressure bore, a 3" high pressure bore, a 3-1/" stroke and can be run at r.p.m. Available options included in this manual: -hooded air filter -hooded air filter / silencer -high pressure rated cylinder and head CHANGES since previous printing dated July 000: -Record of Change 106 involved redesigned head and intercooler. TABLE OF CONTENTS Serial Identification... Ordering Replacement s... Quin-Cip Oil... Crankcase Lubricant Capacity... Crankshaft Group... 3 Crankcase Group... 4 Bearing Carrier Groups with oil filter less oil filter Connecting Rod & Piston Groups low pressure high pressure Cylinder & Head Groups Control Version P Control Versions L, S, LS, LVD Head Assemblies Control Versions P Control Versions L, S, LS, LVD Suction Valve Assembly Discharge Valve Assembly Unloader Assembly Pneumatic Unloader Assembly... 0 Control Groups Version L... 1 Version S... Version LS... 3 Version LVD... 4 Pilot Valves... 5 Pilot Valve Repair Kit... 5 Differential Setting Charts... 5 Suction Valve Unloader Assemblies... 6 Hydraulic Unloader Assemblies... 7 Decals... 8 Gasket Set... 8 Recommended Spare s... 8 Kits... 8 Typical Unit Repair s List , October Wismann Lane, Quincy IL

3 MODEL & SERIAL NUMBER IDENTIFICATION Record of Change No. QUIN-CIP OIL Refer to the chart below to order Quin-Cip compressor oil from your local Authorized Quincy Distributor. Package No. Barrel 11541D03 55 gal., SAE 10W Pail 11541P03 5 gal., SAE 10W Gallon 11541G03 1 gal., SAE 10W Gallon Case 11541X03 (4)-1 gal., SAE 10W Quart 11541Q03 1 qt., SAE 10W Quart Case 11541C03 (1)-1 qt., SAE 10W Model & Serial Identification Tag The model & serial number tag is located on the handhole plate side of the crankcase. Fill in the numbers from your compressor's tag in the corresponding spaces provided here and reference this page when ordering replacement parts. All replacement parts are to be ordered through an authorized Distributor. Insist on genuine Quincy parts only! Failure to do so may void warranty. Barrel 1154D gal., SAE 0 Pail 1154P068 5 gal., SAE 0 Gallon 1154G068 1 gal., SAE 0 Gallon Case 1154X068 (4)-1 gal., SAE 0 Quart 1154Q068 1 qt., SAE 0 Quart Case 1154C068 (1)-1 qt., SAE 0 Barrel 11543D gal., SAE 30 Pail 11543P100 5 gal., SAE 30 Gallon 11543G100 1 gal., SAE 30 Gallon Case 11543X100 (4)-1 gal., SAE 30 Quart 11543Q100 1 qt., SAE 30 Quart Case 11543C100 (1)-1 qt., SAE 30 CRANKCASE LUBRICANT CAPACITY Model Less Filter With Filter QR / 4 qts. (4.5 lit.) Add 10 oz. (96 ml) ORDERING REPLACEMENT PARTS Prompt service can be rendered on repair parts orders if the following information is given: 1) the model number, record of change number, & serial number. ) the exact part number needed. (Do not order by item numbers.) 3) the exact quantity needed. 4) the preferred type of transportation CAUTION! Refer to the QR-5 Series Instruction Manual for vital lubrication information. CAUTION! Follow all safety precautions outlined in the QR-5 Series instruction manual. WARNING! Do not operate this compressor without a totally enclosed belt guard or any other required safety equipment. DANGER! Air used for breathing or food processing must meet O.S.H.A or F.D.A. 1 C.F.R regulations , October Wismann Lane, Quincy IL

4 CRANKSHAFT GROUP Qty crankshaft assembly includes: R crankshaft bearing cone bearing cone orifice, 1/8 npt pipe plug, 1/8 npt F17 roll pin, 3/16 x X sheave assembly includes: R sheave, 19-1/", 4 gr, B sect., CCW (N.S.S.: order 11053X) N hex. screw, 1/-0 unf x 3.5, grade 5 (@ 90 ft.-lbs.) N0 square nut, 1/-0 unf taper key CRANKSHAFT GROUP (for basic compressors used on FE 340 units) Qty crankshaft assembly includes: R crankshaft bearing cone bearing cone orifice, 1/8 npt pipe plug, 1/8 npt F17 roll pin, 3/16 x X sheave assembly includes: R sheave, 16", gr, B sect., CCW (N.S.S.: order X) N hex. screw, 1/-0 unf x 3.5, grade 5 (@ 90 ft.-lbs.) N0 square nut, 1/-0 unf taper key N.S.S. = Not Sold Indicates torque value in foot pounds (dry threads) For reversal of compressor rotation refer to QR-5 instruction manual , October Wismann Lane, Quincy IL

5 CRANKCASE GROUP Qty X crankcase assembly R crankcase (N.S.S.; order 6904X) bearing cup pipe plug, 1/ npt 3 * 1383 bearing adjustment shim,.005 steel 4 * 1383A bearing adjustment shim,.007 steel 5 * 1383B bearing adjustment shim,.00 steel 6 * 1383D bearing adjustment shim,.00 steel adjustment plate (.0015 /.003 crankshaft end play) L1 hex. screw, 3/8-16 unc x 1.00, grade 5 (@ 30 ft.-lbs.) inspection plate gasket inspection plate inspection plate K1 hex. screw, 5/16-18 unc x 1.00, grade 5 (@ 1 ft.-lbs.) X001 oil gauge assembly oil gauge rod (N.S.S.; order 676X001) oil gauge knob (N.S.S.; order 676X001) "o"ring, 1/8" wide x 1.00 o.d breather ball drive pin N031 flatwasher, 5/16 N.S.S. = Not Sold Indicates torque value in foot pounds (dry threads) , October Wismann Lane, Quincy IL

6 BEARING CARRIER GROUP (with oil filter) , October Wismann Lane, Quincy IL

7 BEARING CARRIER GROUP (with oil filter) Qty. * bearing carrier assembly bearing carrier assembly includes: 1 70 bearing cup bronze bushing * "o"ring, 3/3 wide x 3.44 o.d. * "o"ring, 3/3 wide x.69 o.d bearing carrier driveshaft driveshaft key pump gerotor retaining ring oil pump housing J1 hex screw, 1/4-0 unc x 1.00, grade 5 (@ 6 ft.-lbs.) pipe plug, 1/4 npt adjustment screw * "o"ring, 1/16 wide x.44 o.d. (oil pressure adjustment screw) P0 jamnut, 9/16-18 unf spring needle valve pipe plug, 1/8 npt bearing carrier gasket L1 hex. screw, 3/8-16 unc x 1.00, grade 5 (@ 30 ft.-lbs.) oil pressure gauge gasket, oil inlet bracket oil pickup tube C lockwasher, 3/ L11 hex. screw, 3/8-16 unc x.88, grade 5 (@ 30 ft.-lbs.) oil filter stud Maintenance s * oil filter (six pack) Oil Pump Repair Kit (includes 1 each of items 1., 1.3, 1.4, 1.5, 1.6, 1.7, & 1.1) 11081X003 Replacement Bearing Carrier Assembly (includes 1 each of items 1,, 5, 9, & 1 oil filter) * Can not be used with diester or phosphate ester based synthetic lubricants. Install with Teflon tape , October Wismann Lane, Quincy IL

8 BEARING CARRIER GROUP (less oil filter) , October Wismann Lane, Quincy IL

9 BEARING CARRIER GROUP (less oil filter) Qty bearing carrier assembly bearing carrier assembly includes: 1 70 bearing cup bronze bushing * "o"ring, 3/3 wide x 3.44 o.d. * "o"ring, 3/3 wide x.69 o.d bearing carrier driveshaft driveshaft key pump gerotor retaining ring oil pump housing J1 hex screw, 1/4-0 unc x 1.00, grade 5 (@ 6 ft.-lbs.) pipe plug, 1/4 npt adjustment screw * "o"ring, 1/16 wide x.44 o.d. (oil pressure adjustment screw) P0 jamnut, 9/16-18 unf spring needle valve bearing carrier gasket L1 hex. screw, 3/8-16 unc x 1.00, grade 5 (@ 30 ft.-lbs.) oil pressure gauge gasket, oil inlet bracket oil pickup tube C lockwasher, 3/ L11 hex. screw, 3/8-16 unc x.88, grade 5 (@ 30 ft.-lbs.) Maintenance s Oil Pump Repair Kit (includes 1 each of items 1., 1.3, 1.4, 1.5, 1.6, 1.7, & 1.1) 11081X00 Replacement Bearing Carrier Assembly (includes 1 each of items 1,, & 5) * Can not be used with diester or phosphate ester based synthetic lubricants. Install with Teflon tape , October Wismann Lane, Quincy IL

10 CONNECTING ROD & PISTON GROUP (low pressure) 1. 6 RING GAPS TO BE STAGGERED WHEN ASSEMBLED. PIP MARKS INDICATE TOP SURFACE OF RING , October Wismann Lane, Quincy IL

11 CONNECTING ROD & PISTON GROUP (low pressure) Qty connecting rod assembly (N.S.S.; order 6655X) R connecting rod (N.S.S.; order 6655X) connecting rod bearing (N.S.S.; order 6443SR) connecting rod bolt, 7/16-0 unc x connecting rod bolt washer 8648 retaining ring piston pin piston oil ring piston ring connecting rod insert (sold in pairs only; see maintenance parts) M08 locknut, 7/16-0 unf (@ 40 ft.-lbs.) Maintenance s PR inserts, connecting rod (1 pair, standard size) PR inserts, connecting rod (1 pair,.010 undersize) SR replacement connecting rod bearing piston, low pressure (.010 oversize) piston, low pressure (.00 oversize) A Piston Ring Set (standard) includes piston rings & oil ring Piston Ring Set (.010 oversize, light blue color code) includes includes piston rings & oil ring Piston Ring Set (.00 oversize, yellow color code) includes includes piston rings & oil ring 1 864X Piston Assembly, low pressure (standard) includes ring set, piston pin, retaining rings, & piston 864X010 Piston Assembly, low pressure (.010 oversize) includes ring set, piston pin, retaining rings, & piston 864X00 Piston Assembly, low pressure (.00 oversize) includes ring set, piston pin, retaining rings, & piston 6655X Replacement Connecting Rod Assembly includes connecting rod assembly, connecting rod inserts, & locknuts N.S.S. = Not Sold Indicates torque value in foot pounds (dry threads) , October Wismann Lane, Quincy IL

12 CONNECTING ROD & PISTON GROUP (high pressure) RING GAPS TO BE STAGGERED WHEN ASSEMBLED. PIP MARKS INDICATE TOP SURFACE OF RING , October Wismann Lane, Quincy IL

13 CONNECTING ROD & PISTON GROUP (high pressure) Qty connecting rod assembly (N.S.S.; order X) connecting rod (N.S.S.; order X) needle bearing connecting rod bolt, 7/16-0 unc x connecting rod bolt washer orifice plug 8648 retaining ring piston pin piston oil ring rail expander ring piston ring connecting rod insert (sold in pairs only; see maintenance parts) M08 locknut, 7/16-0 unf (@ 40 ft.-lbs.) Maintenance s PR inserts, connecting rod (1 pair, standard size) PR inserts, connecting rod (1 pair,.010 undersize) piston, high pressure (.010 oversize) piston, high pressure (.00 oversize) 1 645A Piston Ring Set (standard) includes piston rings, oil ring rails & expander Piston Ring Set (.010 oversize, light blue color code) includes includes piston rings, oil ring rails & expander Piston Ring Set (.00 oversize, yellow color code) includes includes piston rings, oil ring rails & expander 1 008X001 Piston Assembly, high pressure (standard) includes ring set, piston pin, retaining rings, & piston 008X011 Piston Assembly, high pressure (.010 oversize) includes ring set, piston pin, retaining rings, & piston 008X01 Piston Assembly, high pressure (.00 oversize) includes ring set, piston pin, retaining rings, & piston X Replacement Connecting Rod Assembly includes connecting rod assembly, connecting rod inserts, & locknuts N.S.S. = Not Sold Indicates torque value in foot pounds (dry threads) , October Wismann Lane, Quincy IL

14 CYLINDER & HEAD GROUP (control version P) , October Wismann Lane, Quincy IL

15 CYLINDER & HEAD GROUP (control versions L, S, LS & LVD) , October Wismann Lane, Quincy IL

16 HEAD ASSEMBLY P (control version P) , October Wismann Lane, Quincy IL

17 HEAD ASSEMBLY UU (control versions L, S, LS & LVD) , October Wismann Lane, Quincy IL

18 SUCTION VALVE VE ASSEMBLY 777X , October Wismann Lane, Quincy IL

19 DISCHARGE VAL ALVE ASSEMBLY 771X , October Wismann Lane, Quincy IL

20 UNLOADER ASSEMBLY , October Wismann Lane, Quincy IL

21 PNEUMATIC UNLOADER ASSEMBLY , October Wismann Lane, Quincy IL

22 CONTROL GROUP (control versions L) Qty p.s.i p.s.i hydraulic unloader assembly tube fitting, 90 male elbow, 1/4 tube x 1/8 npt 3 4 ft copper tube, 1/4 o.d tube fitting, male branch tee, 1/4 tube x 1/4 tube x 1/8 npt Maintenance s Hydraulic Unloader Repair Kit includes diaphragm, stem assembly, inlet filter & fitting assembly, spring (0-00 p.s.i.) and spring ( p.s.i., red color code) s for Special Applications (for use with diester or phosphate ester synthetic lubricants) hydraulic unloader assembly (standard, 0-00 p.s.i.) hydraulic unloader assembly (high pressure, p.s.i.) 4 3 1/4 o.d. tube from receiver , October Wismann Lane, Quincy IL

23 Qty. CONTROL GROUP p.s.i p.s.i pilot valve assembly * pilot valve tube fitting, straight male connector, 3/8 tube x 1/4 npt mounting stud J J05 set screw, 1/4-8 unf x.38, grade pipe plug, 1/4 npt, hex socket 4 ft copper tube, 1/4 o.d tube fitting, male branch tee, 1/4 tube x 1/4 tube x 1/8 npt tube fitting, 90 male elbow, 1/4 tube x 1/8 npt tube fitting, 90 male elbow, 1/4 tube x 1/4 npt (control version S) * See page 5 for optional pilot valves that must be used with respective pressure ranges /8 o.d. tube from receiver , October Wismann Lane, Quincy IL

24 CONTROL GROUP (control version LS) Qty p.s.i p.s.i pilot valve assembly pilot valve hydraulic unloader assembly mounting stud J J05 set screw, 1/4-8 unf x.38, grade brass pipe tee, 1/4 npt x 1/4 npt x 1/4 npt tube fitting, 90 male elbow, 1/4 tube x 1/8 npt ft copper tube, 1/4 o.d tube fitting, straight male connector, 1/4 tube x 1/8 npt tube fitting, 90 male elbow, 1/4 tube x 1/4 npt tube fitting, straight male connector, 3/8 tube x 1/4 npt 4 ft copper tube, 1/4 o.d tube fitting, male branch tee, 1/4 tube x 1/4 tube x 1/8 npt tube fitting, 90 male elbow, 1/4 tube x 1/8 npt tube fitting, 90 male elbow, 1/4 tube x 1/4 npt Maintenance s Hydraulic Unloader Repair Kit includes diaphragm, stem assembly, inlet filter & fitting assembly, spring (0-00 p.s.i.) and spring ( p.s.i. red color code) s for Special Applications (for use with diester or phosphate ester synthetic lubricants) hydraulic unloader assembly (standard, 0-00 p.s.i.) hydraulic unloader assembly (high pressure, p.s.i.) * See page 5 for optional pilot valves that must be used with respective pressure ranges /8 o.d. tube from receiver , October Wismann Lane, Quincy IL

25 CONTROL GROUP (control version LVD) Qty p.s.i p.s.i pilot vlave assembly pilot valve hydraulic unloader assembly mounting stud J J05 set screw, 1/4-8 unf x.38, grade brass pipe tee, 1/4 npt x 1/4 npt x 1/4 npt tube fitting, 90 male elbow, 1/4 tube x 1/8 npt ft copper tube, 1/4 o.d tube fitting, straight male connector, 1/4 tube x 1/8 npt tube fitting, 90 male elbow, 1/4 tube x 1/4 npt tube fitting, straight male connector, 3/8 tube x 1/4 npt 4 ft copper tube, 1/4 o.d tube fitting, male branch tee, 1/4 tube x 1/4 tube x 1/8 npt tube fitting, 90 male elbow, 1/4 tube x 1/8 npt tube fitting, 90 male elbow, 1/4 tube x 1/4 npt Maintenance s Hydraulic Unloader Repair Kit includes diaphragm, stem assembly, inlet filter & fitting assembly, spring (0-00 p.s.i.) and spring ( p.s.i. red color code) s for Special Applications (for use with diester or phosphate ester synthetic lubricants) hydraulic unloader assembly (standard, 0-00 p.s.i.) hydraulic unloader assembly (high pressure, p.s.i.) * See page 5 for optional pilot valves that must be used with respective pressure ranges /8 o.d. tube from receiver , October Wismann Lane, Quincy IL

26 PILOT VAL ALVES check ball air from receiver air out to head unloaders unload adjustment differential adjustment toggle lever series pilot valve (control version S) 1 check ball differential adjustment Available Pilot Valves Refer to illustrations at left to determine pilot valve series; add dash # listed below per pressure setting. Pressure Setting Dash # (p.s.i.) Notes adjustable unload pressure / customer to set, see differential setting chart adjustable unload pressure / customer to set, see differential setting chart adjustable unload pressure / customer to set, see differential setting chart adjustable unload pressure / customer to set, see differential setting chart Additional factory preset valves are available upon request. air from receiver air out to head unloaders 3 4 toggle lever unload adjustment 1114 series pilot valve (control version LS) 1 5 check ball air in from hydraulic unloader differential adjustment Pilot Valve Repair Kit Can be used to repair 11083, 1114 & series pilot valves. Customer must specify which spring when ordering pilot valve repair kit. # Qty. 1 screen 1 filter 3 1 "o"ring replacement spring, pilot valve, p.s.i. (red) replacement spring, pilot valve, p.s.i. (yellow) replacement spring, pilot valve, p.s.i. (green) replacement spring, pilot valve, p.s.i. (black) disc air inlet unload adjustment air in from hydraulic unloader knurled knob air out to head unloaders series pilot valve (control version LVD) WARNING! Not all pilots are for use with all compressor systems. Make sure that the pilot you order is set within the safe operating limits of your compressor. Failure to heed this warning could result in an explosion. Differential Setting Chart Spring # Unload Min. Dif. (item 4) (p.s.i.) (p.s.i.) Max. Dif. (p.s.i.) " " " " " " " " " " " " " " " " " , October Wismann Lane, Quincy IL

27 SUCTION VALVE UNLOADER ASSEMBLIES The Quincy suction valve unloader assembly consists of unloading arrangements on the suction valves, having a plunger to contact the suction valve disc and an unloader pilot valve (part no.s ***, and 1114-*** & ***) to automatically regulate the passing of receiver pressure to the unloading arrangement. Application Suction valve unloader assemblies are recommended for use on Quincy compressors where the compressor is to run continuously and a constant pressure is to be maintained. The purpose is to automatically unseat the suction valve of the compressor when the air supply is greater than the demand. Operation Unloading occurs when receiver pressure is sufficient to overcome pilot valve spring pressure. The check ball is then unseated, allowing receiver pressure to pass to the unloading arrangements. The compressor will run unloaded until the receiver pressure drops to a predetermined level. At this time, the action of the ball is reversed, shutting off receiver pressure to the unloader arrangement and venting the unloader to atmosphere. This allows the compressor to load. The drive, either electric motor or combustion engine, runs continuously and must be started and stopped manually. Pilot valve *** can be locked out, for models equipped with dual control, to provide automatic start/stop operation. The knurled knob at the top of the pilot can be turned clockwise, until it stops, to lock it out. A pressure switch is required to stop the motor. Failure to use a pressure switch, with the pilot valve locked out, could result in unsafe conditions. WARNING! A pressure switch must be incorporated whenever pilot valve *** is employed as part of the control system. The compressor will operate in the continous run mode if the knurled knob is turned counterclockwise until it stops. Installation The pilot valve is to be connected to the air receiver using a minimum of 3/8" o.d. copper tube. Compressors in the field, not equipped with a suction valve unloader assembly, can be converted to constant speed. Consult your local Distributor for assistance with conversion procedures. Service Periodically check the filter & screens in the inlet of the pilot valve to make sure they are free of obstructions. If they become clogged, remove and clean or replace. Inspect the "o"ring located in the opposite end of the pilot valve body for wear or damage; replace if necessary. Adjustment The unloading pressure is adjustable and is regulated by turning the hex nut (marked "unload adj." in cross sectional illustrations of pilot valves). Turn the hex nut clockwise to increase and counterclockwise to decrease the unloading pressure. The differential (difference between unloading and loading pressure) is set by turning the hex nut (marked "differential adj." in the cross sectional illustrations of the pilot valves). Increase the differential pressure by turning the hex nut clockwise - decrease by turning counterclockwise. Tighten the locknuts after adjustment. CHECK VALVE ASSEMBLIES Check Valve Assembly Replacement s # Qty. 6194X Check Valve Assembly "o"ring disc 6194X3 Check Valve Assembly (for use with diester or phosphate ester synthetic lubricants) "o"ring disc , October Wismann Lane, Quincy IL

28 HYDRAULIC UNLOADER ASSEMBLIES Hydraulic Unloader & * *for use with diester or phosphate ester synthetic lubricants Not all hydraulic unloader assemblies are for use with all compressor systems. Make sure that the hydraulic unloader assembly you order is within the operating limits of your system. Hydraulic Unloader Assembly Repair Kit 1135 # Qty. 1 1 diaphragm 1 stem assembly (includes - "o"rings) 3 1 filter assembly (includes fitting & screens) 4 1 spring , October Wismann Lane, Quincy IL

29 # Qty. # Qty. # Qty. # Qty. # Qty. Head Kit K340A valve disc valve spring gasket, valve 668 valve cover gasket 185 gasket, valve cover 1556 gasket, valve 1855 diaphragm cylinder to head gasket E100 air filter element 570 intercooler to head gasket Overhaul Kit K340B V.I.P. Kit E100 air filter element 1855 diaphragm valve disc 6656PR connecting rod inserts (1 pair) valve spring gasket set 1 645A ring set A ring set Piston Pin Kit K340E SR con-rod bearing piston pin piston pin needle bearing 8648 retaining ring Recommended Spare s 3 777X replacement suction valve assy X0 replacement discharge valve assy pressure gauge oil pump repair kit gasket set hydraulic unloader repair kit 6656PR connecting rod inserts (1 pair) 1855 unloader diaphragm pilot repair kit E100 air filter element oil pressure gauge 1855 diaphragm valve pin valve disc 683 hydraulic unloader filter valve spring valve spring gasket set Basic Compressor Repair Kit # Qty. # Qty. # Qty piston pin E100 air filter element "o"ring kit oil filter 1 70 bearing cup bearing cone bearing cup bearing cone 6443SR connecting rod bushing 6656PR connecting rod inserts (1 pair) valve spring gasket set ring set valve disc piston pin ring set Gasket Set inspection plate gasket bearing adj. shim,.005 steel A bearing adj. shim,.007 steel B bearing adj. shim,.00 steel 1383D bearing adj. shim,.00 steel 1556 gasket valve gasket 185 valve cover gasket gasket gasket, cylinder to crankcase 588 gasket, companion flange gasket, intercooler to head gasket, oil inlet bracket 668 valve cover gasket gasket, cylinder to head Decals serial number & nameplate A decal, CAUTION!/manual/ "Failure to follow..." B decal, DANGER! / "Air used for breathing..." * Not sold separate; order , October Wismann Lane, Quincy IL

30 TYPICAL UNIT REPAIR PAR ARTS LIST The parts listed here are for standard (up to 175 p.s.i.) units and may or may not be applicable to custom built units. Check with your local authorized Distributor for parts that can be used for custom built units. Make sure the components you order are rated within the safe operating limits of your system. If you are doubtful about which components to order, contact you local Quincy distributor. ( simplex - horizontal tank - electric motor) Qty 80 gal. 10 gal tank (00 p.s.i. max. working pressure) * top plate tank drain valve ball valve pressure gauge pressure switch ( p.s.i.) pressure relief valve (00 p.s.i.) 3.5 ft ! discharge tube (1" copper tube to be formed by customer) ferrule (for discharge tube) 7.5 H.P B08 drive belt 1 30 motor pulley K00 belt guard assembly motor pulley bushing 00v, 3Ø 30/460v, 3Ø h.p. motor (O.D.P.) ( duplex - horizontal tank - electric motor) Qty 10 gal. 00 gal tank (00 p.s.i. max. working pressure) top plate tank drain valve ball valve pressure gauge pressure switch ( p.s.i.) pressure relief valve (00 p.s.i.) 7 ft ! discharge tube (1" copper tube to be formed by customer) ferrule (for discharge tube) 7.5 H.P B08 drive belt 30 motor pulley K00 belt guard assembly motor pulley bushing 00v, 3Ø 30/460v, 3Ø h.p. motor (O.D.P.) * top plate is also used for all base mounted electric motor driven units pressure switch on base mounted units. numbers shown in italics apply to tank mounted units and base mounted units.! Pre-formed discharge tubes are available. Contact factory with model & tank size information , October Wismann Lane, Quincy IL

31 Quincy Service is always near. There are authorized Quincy Distributors located throughout the United States & Canada that stock genuine Quincy parts & accessories for a wide range of Quincy products. Quincy Service specialists are factory trained and will help keep you in business. Call for Authorized Quincy Service. Quincy Compressor True Blue Reliability TM Reciprocating / Systems: Rotary / Vacuum / Systems: Nearest Distributor: trueblue.quincy@goodrich.com Discover: a Goodrich Corporation Business All Rights Reserved. Litho in U.S.A.