Gauges / Pin gauges / Thread and tolerance tables

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Gauges / Pin gauges / Thread and tolerance tables"

Transcription

1 Gauges / Pin gauges / Thread and tolerance tables C2.00.EN-dealer , Schut Geometrische Meettechniek bv 27 Measuring instruments and systems 20/202-D

2 Limit gauges for internal and external dimensions The manufacturing tolerance and the permissible reduction in wear for plain gauges are laid down in DIN 762. New gauges are supplemented with a wear allowance on the Go end: z (plus) for plug gauges and z (minus) for ring gauges. Accordingly, the size indicated on the handle is not similar to the measured value of the new Go end. Example: plug gauge 0 H9 New Go end: size wear allowance (+ z) manufacturing tolerance ± largest value measured 0.0 smallest value measured The gauges are also available without wear allowance (additional cost). This should be indicated when ordering. Plug gauges Measuring reports For all gauges also measuring reports can be ordered. Inspection report (German) per gauge. Stating of product specifications, measured values after production, used traceable measuring devices, measuring inaccuracy and measuring date. A favourable choice when your quality system does not require traceable (RvA) certificates. Traceable RvA certificate (Dutch) with measuring reports of the ordered gauges. Besides stating of the measured values the extra assurance of an external RvA inspection. Manufactured according DIN 2245, 2246 and Available from 0.5 to 250 ; up to 70 with Go and NoGo on one handle, over 70 in two parts. s are for H7 plug gauges with Go and NoGo ends in hardened steel. Also available: other fit sizes, like H6 and H8, hard-chrome plated plug gauges, tungsten carbide plug gauges, extended plug gauges, plug gauges with vent hole, plug gauges with easy-entry pilot, flat plug gauges, square and hexagonal plug gauges. Size H7/ Size H7/ Size H7/ Size H7/ Larger sizes available on request C2.202.EN-dealer , Schut Geometrische Meettechniek bv 28 Measuring instruments and systems 20/202-D

3 PIN Pin gauges Swiss made, hardened and ground steel pin gauges; available loose and in sets. Hardened, ground, and seasoned steel. Diameter range: without handle: , with handle: Increment: 0.0. Accuracy: ± Pin gauges ø without handle: indication on head. Diameter/ Length/ Pin gauge without handle: Pin gauge with handle 2 : Delivery in plastic transport case. 2 The length here indicates the measuring length and not the total length of the pin gauges. Item No. Description Wooden case (tubes not included): 8.2 For 50 pin gauges ø without handle For 00 pin gauges ø without handle For 50 pin gauges ø with handle 8.8 For 40 pin gauges ø For 80 pin gauges ø For 0 pin gauges ø Pin gauge tube for pin gauges: Without handle up to ø Without handle ø With handle up to ø Base inscription per size Also available: With an accuracy of ± or ± 0.00 ; hardened steel ø , tungsten carbide or ceramics ø , with 0.0 increments. The length may deviate. More information available on request. C2.204.EN-dealer , Schut Geometrische Meettechniek bv 29 Measuring instruments and systems 20/202-D

4 PIN Pin gauges in sets Hardened, ground, and seasoned steel. Diameter range: Increment: 0.0. Accuracy: ± Without handle. Pin gauges ø : indication on head. Length: ø : 40, ø : 70. Sets with larger diameters and/or with handle are available on request. Item No. Diameter Increment Number per set * s per set, in wooden case. * Set pin gauges without handle Individual pin gauges without handle Pin gauges accessories Interchangeable handles For pin gauges without handle. Holders for Go/NoGo determination For two pin gauges without handle. With NoGo indication. Item No. For diameter/ Item No. For diameter/ C2.20.EN-dealer , Schut Geometrische Meettechniek bv 220 Measuring instruments and systems 20/202-D

5 PIN Pin gauges Ground and lapped, hardened tool steel pin gauges with a high accuracy. Available per piece and in sets. Swiss made. Diameter range: ø Increment: 0.0. Accuracy: ± Hardened tool steel. Ground and lapped. Measuring length (and total length): ø : 2 (4 ), ø :.5 (5.5 ), ø : 5 (7 ), ø : 6 (8 ), ø : 8 (4 ), ø : 0 (55 ), ø : 4 (59 ), ø : 8 (6 ). Size indication on the insulated handle. Per piece Diameter/ Sets Item No. Diameter Pieces C2.02.EN-dealer , Schut Geometrische Meettechniek bv 22 Measuring instruments and systems 20/202-D

6 Setting rings Setting rings, manufactured according DIN 2250 form C, to 5. The size is indicated on the ring to three decimal places, to 50 setting rings are also available in tungsten carbide as are form B rings for pneumatic measuring tools. s for intermediate and larger sizes are available on request. Size Size Size Size Size Intermediate sizes over are also available Measuring reports For all gauges also measuring reports can be ordered. Inspection report (German) per gauge. Stating of product specifications, measured values after production, used traceable measuring devices, measuring inaccuracy and measuring date. A favourable choice when your quality system does not require traceable (RvA) certificates. Traceable RvA certificate (Dutch) with measuring reports of the ordered gauges. Besides stating of the measured values the extra assurance of an external RvA inspection. C2.205.EN-dealer , Schut Geometrische Meettechniek bv 222 Measuring instruments and systems 20/202-D

7 Taper gauges To increase the already large capacity to transmit moments, some taper gauges are furnished with a lip which functions as catch lock Morse taper gauges Morse Plug: Ring: Plug: Ring: Metric taper gauges metric Without lip, DIN 229 Item No. Item No. Without lip, DIN 24 Item No. Item No. Plug: Ring: Plug: Ring: With lip, DIN 20 Item No. Item No. With lip, DIN 25 Item No. Item No. Short taper gauges SK Plug, DIN 2079 Item No. Ring, DIN 2080 Item No C2.206.EN-dealer , Schut Geometrische Meettechniek bv 22 Measuring instruments and systems 20/202-D

8 Measuring mandrels The cylinders are hollow and have four marks on the cylinder wall near the thread and numbered marks in successive distances of 90 on the face. The cylinder and the front face are ground and lapped. The hardness is (60 ± 2) HRc. Measuring mandrels with internal thread, without external screw thread and nut Item No. Cone Dimensions cylinder ø/ length/ Sc Sc Sc Sc Sc Sc Sc Specifications of the accuracy: straightness of the cylinder µm, out of roundness µm, eccentricity µm. Measuring mandrels without draw bar thread, with external screw thread and nut Item No. Cone Dimensions cylinder ø/ length/ Mc Mc Mc Mc Mc Mc Mc Mec Other models are available. Gauges for keyway depths on shafts With interchangeable gauge parts. Available in all coon fits. s available on request. C2.207.EN-dealer , Schut Geometrische Meettechniek bv 224 Measuring instruments and systems 20/202-D

9 Thread gauges The prices of the thread gauges apply to the following tolerances: Kind of thread gauge Other tolerances, sizes and kinds of threads are available on request; also available are special screw threads as per your design. Left-hand screw thread: price on request. Measuring reports Tolerances gauge Metric thread according ISO 502 up to and incl. M.4 5H 6h larger than M.4 6H 6g (standard) 4h and 6e Fixing pipe thread DIN ISO 228 center A Trapezoidal thread DIN 0 7H 7e For all gauges also measuring reports can be ordered. Inspection report (German) per gauge. Stating of product specifications, measured values after production, used traceable measuring devices, measuring inaccuracy and measuring date. A favourable choice when your quality system does not require traceable (RvA) certificates. Traceable RvA certificate (Dutch) with measuring reports of the ordered gauges. Besides stating of the measured values the extra assurance of an external RvA inspection. and ring gauges Hardened steel thread plug gauges (up to M9: Go + NoGo, from M42: Go and NoGo separate) and thread ring gauges (Go or NoGo) for metric screw thread (ISO) with coarse pitch (ISO 502). M... x x x 0..6 x x x x x 0.45 x x x x x x 8 x.25 0 x.5 2 x.75 4 x 2 6 x 2 8 x x x x 27 x 0 x.5 x.5 6 x 4 9 x 4 Thread M... Go NoGo ring 42 x x x 5 52 x 5 56 x x 5.5 C2.208.EN-dealer , Schut Geometrische Meettechniek bv 225 Measuring instruments and systems 20/202-D

10 and ring gauges (continued) Hardened steel thread plug gauges (Go + NoGo) and thread ring gauges (Go or NoGo) for metric screw thread (ISO) with pitch 0.5 (ISO 502). M... x Hardened steel thread plug gauges (Go + NoGo) and thread ring gauges (Go or NoGo) for metric screw thread (ISO) with pitch (ISO 502). M... x Hardened steel thread plug gauges (Go + NoGo) and thread ring gauges (Go or NoGo) for metric screw thread (ISO) with pitch 0.75 (ISO 502). M... x Hardened steel thread plug gauges (up to M40: Go + NoGo, from M42: Go and NoGo separate) and thread ring gauges (Go or NoGo) for metric screw thread (ISO) with pitch.5 (ISO 502). M... x (continued on the next page) C2.209.EN-dealer , Schut Geometrische Meettechniek bv 226 Measuring instruments and systems 20/202-D

11 and ring gauges (continued) M... x.5 (continued) Thread M... x.5 Go NoGo ring Hardened steel thread plug gauges (up to M40: Go + NoGo, from M42: Go and NoGo separate) and thread ring gauges (Go or NoGo) for metric screw thread (ISO) with pitch 2 (ISO 502). M... x Thread M... x 2 Go NoGo ring Hardened steel thread plug gauges (up to G": Go + NoGo, from G / 8 ": Go and NoGo separate) and thread ring gauges (Go or NoGo) for non-sealing fixing pipe thread (DIN ISO 228). G..." / 8 / 4 / 8 / 2 5 / 8 / 4 7 / 8 Thread G..." Go NoGo ring / 8 / 4 / 2 / / 4 2 / 2 2 / 4 Hardened steel thread plug and thread ring gauges for sealing pipe thread (DIN 2999). R..." / 8 / 4 / 8 / 2 / 4 / 4 / 2 2 Larger sizes available on request C2.20.EN-dealer , Schut Geometrische Meettechniek bv 227 Measuring instruments and systems 20/202-D

12 and ring gauges (continued) Hardened steel thread plug gauges (up to / 4 : Go + NoGo, from / 8 : Go and NoGo separate) and thread ring gauges (Go or NoGo) for American screw thread UNC and UNF according ANSI B. class 2B (thread plug) and 2A (thread ring). UNC No - 64 No 2-56 No - 48 No 4-40 No 5-40 No 6-2 No 8-2 No 0-24 No 2-24 / / 6-8 / / 6-4 / 2-9 / / 8 - / / / 8-7 / 4-7 Thread UNC Go NoGo ring / 8-6 / 2-6 / / 2 2 / 4-4 / 2 2 / / / 4-4 / 2-4 / UNF No 0-80 No - 72 No 2-64 No - 56 No 4-48 No 5-44 No 6-40 No 8-6 No 0-2 No 2-28 / / 6-24 / / 6-20 / / / 8-8 / / / 8-2 / 4-2 Thread UNF Go NoGo ring / 8-2 / 2-2 C2.2.EN-dealer , Schut Geometrische Meettechniek bv 228 Measuring instruments and systems 20/202-D

13 and ring gauges (continued) Hardened steel tapered thread plug and thread ring gauges for sealing pipe thread according ANSI/ASME B.20.. NPT..." / 6 / 8 / 4 / 8 / 2 / 4 / 4 / / 2 and ring gauges in sets Sets of thread plug gauges or thread ring gauges for inspection of metric ISO threads. For threads M, M4, M5, M6, M8, M0 and M2. Tolerance class: thread plug gauges: 6H, thread ring gauges: 6g. Hardened steel. ISO 502. Delivery in a wooden case with an inspection report Item No. Thread gauges set Plug gauges (Go + NoGo) Ring gauges (Go) Ring gauges (NoGo) Thread jaw gauges Jaw shaped gauge for inspection of external screw thread. Delivery excl. setting thread plug gauge. Available on request. C2.22.EN-dealer , Schut Geometrische Meettechniek bv 229 Measuring instruments and systems 20/202-D

14 / MEASURING WEDGES Drill gauges Gauge in the form of a steel plate with bores of increasing diameters for determining drill diameters. Twist drill grinding gauges For checking twist drills for the place and the 8 angle of the twist drill point. The maximum drill diameter is Item No. Meas. range Increment Number of bores Universal twist drill grinding gauge, also called Y gauge. Besides the standard angle of 8, this gauge also has a 90 angle for countersink drills, and some special angles for center drills. Item No. Description Twist drill grinding gauge Y gauge Measuring wedges Measuring wedges for quick measurements and checks of slits, key-ways, distances, etc. Measuring range: Graduation: 0.05, 0. or Item No. Measuring range/ Graduation C2.0.EN-dealer , Schut Geometrische Meettechniek bv 20 Measuring instruments and systems 20/202-D

15 Flat plug gauges Measuring range: Graduation: 0.. Stainless steel, no-glare chrome finished. Graduation on both sides. Ground measuring faces. Item No. Measuring range/ Conical plug gauges Measuring range: ø Graduation: 0.. Hardened, ground and chrome finished. With anodized handle ø ø ø ø Item No. Measuring range/ Nozzle gauges Set of pins in holder serving as a gauge to determine jet nozzle sizes. Nozzle gauges with vernier Nozzle gauges with a hardened and ground tapered needle. Measuring range: ø 0-5. Vernier: Item No. Number of pins Sizes ø ø Item No. Measuring range/ ø ø 0-5 C2.2.EN-dealer , Schut Geometrische Meettechniek bv 2 Measuring instruments and systems 20/202-D

16 THREAD CUTTING TOOL Center gauges For checking thread cutting tools for Whitworth thread 55 or metric thread 60. Item No. Description Whitworth 55 Metric Thread cutting tool gauges Item No. Description Universal thread cutting tool gauge for angular thread and flat thread Trapezoidal thread cutting tool gauge for trapezoidal thread DIN 0 (0, 2-2 ) Combined lathe and thread cutting tool gauge for cutting tool wedge angle, trapezoidal thread (0 ), and angular thread (55 and 60 ) Combined lathe and thread cutting tool gauge like , with additional angle stop (0-0 ) on the back Thread cutting tool gauge for rectangular thread, trapezoidal thread (0 ), and angular thread (55 and 60 ) C7.202.EN-dealer , Schut Geometrische Meettechniek bv 22 Measuring instruments and systems 20/202-D

17 ANGLE AND RADIUS Angle gauge set Measuring range: 5-90 (supplementary angles: ). Increment: 5 (8 pieces). Multiple angles per angle gauge: primary angles (, 2 *,, 4), supplementary angles (5, 6), and ½ primary angles (7, 8). Delivery in a case. Angle gauges Measuring range: Number of blades: 20. Angles: * Angle 2: only with the angle gauges from 20. Item No. Description Angle gauge set Item No. Description Angle gauges Radius gauges Measuring range radius: Increment: - : 0.25,.5-20 : 0.5, > 20 :.0. Shape and radius gauge This stainless steel gauge can be used to adopt various complex shapes of tools and workpieces. When the gauge is pressed against the part which has to be checked, it takes on the shape of this part. Because of the graduation () on the case, the shape can be checked easily. Because the tracers were supported under pressure, they don t move on their own. Item No. Radius range/ Item No. Measuring range/ x 40 C7.204.EN-dealer , Schut Geometrische Meettechniek bv 2 Measuring instruments and systems 20/202-D

18 WELDING SEAM AND CALIPERS Set of welding seam gauges For weld thickness: - 2. Up to 7 increasing with 0.5, plus 8, 0 and 2. Total: 2 pieces. Bright steel. Welding seam gauge For measurement of welding seams. Graduation: 0.2. Stainless steel. Delivery in a case. Item No. Description Item No. Description Welding seam gauges Welding seam gauge Welding seam calipers For measurement of welding seams. Measuring range: Analog: vernier 0., digital: resolution 0.0. Delivery in a case. Analog Stainless construction. Digital /inch conversion. On/off switch. Reset. Power supply: battery type V The angles (60, 70, 80 and 90 ) serve as an aid for checking the angle of the hole to be welded. Item No. Measuring range/ Analog: Digital: Option: Spare battery C7.20.EN-dealer , Schut Geometrische Meettechniek bv 24 Measuring instruments and systems 20/202-D

19 TABLES / Thread and tolerance tables Thread table Table with all standard international thread indications: metric, Ww, Gas, BSF, Pg, BA, UNC, UNF and UNEF. Tolerance table Table compromising all tolerances and fits according ISO R286, up to 500 (table with over 6400 pairs of tolerance values for internal and external measurements). Conversion table /inch For converting from to inch and from inch to Item No. Description Thread table Tolerance table Conversion table /inch Flat thickness gauge Screw pitch gauges Gauge to e.g. measure the thickness of steel plating. Measuring range: -. Graduation: 0.5. Stainless steel. Item No. Measuring range/ Item No. Type of thread Metric Whitworth BSP Metric/Whitworth Metric/Whitworth BSP UNC/UNF C2.24.EN-dealer , Schut Geometrische Meettechniek bv 25 Measuring instruments and systems 20/202-D

UNITED STATES CUTTING TOOL INSTITUTE Product Groupings for Standards Activities CUTTING TOOL PRODUCTS

UNITED STATES CUTTING TOOL INSTITUTE Product Groupings for Standards Activities CUTTING TOOL PRODUCTS CUTTING TOOL PRODUCTS 1. BORING ISO 5609 Boring bars for indexable inserts Dimensions ISO 6261 Boring bars (tool holders with cylindrical shank) for indexable inserts Designation JIS B 4128 Boring bars

More information

OUR PRODUCT RANGE SETTING GAUGES P. 39 INSPECTION OF PLAIN SURFACES GAUGES FOR INSPECTION OF THREADS THE CHECKING OF SPLINES AND GEARS SPECIAL GAUGES

OUR PRODUCT RANGE SETTING GAUGES P. 39 INSPECTION OF PLAIN SURFACES GAUGES FOR INSPECTION OF THREADS THE CHECKING OF SPLINES AND GEARS SPECIAL GAUGES OUR PRODUCT RANGE SETTING GAUGES P. 3 INSPECTION OF PLAIN SURFACES P. 9 GAUGES FOR INSPECTION OF THREADS P. 27 THE CHECKING OF SPLINES AND GEARS P. 39 SPECIAL GAUGES P. 45 SPECIAL EQUIPMENT AND SOLUTIONS

More information

NOT SEARCHING, BUT FINDING

NOT SEARCHING, BUT FINDING NOT SEARCHING, BUT FINDING We carefully ensure that our wide and extensive range provides a good assortment so that you feel in good hands, even if you are looking for portable measurement devices to provide

More information

Measuring instruments and systems

Measuring instruments and systems GENERAL CATALOG instruments and systems precision measuring instruments mechanical - optical - electronical 3D CNC coordinate measuring machines SGM Germany Schut Belgium SGM Switzerland Schut France Schut

More information

understand the fundamental of the gauges and their classifications, and

understand the fundamental of the gauges and their classifications, and UNIT 4 LIMIT GAUGING Structure 4.1 Introduction Objectives 4.2 Gauges and their Classifications 4.2.1 Standard Gauges 4.2.2 Limit Gauges 4.3 Working Gauges, Inspection Gauges and Reference Gauges 4.4 Gauges

More information

MACHINE SCREWS AND NUTS

MACHINE SCREWS AND NUTS Previous page Machinery's Handbook 27th Edition MACHINE SCREWS 1587 MACHINE SCREWS AND NUTS American National Standard Machine Screws and Machine Screw Nuts. This Standard ANSI B18.6.3 covers both slotted

More information

Inspection. 9. Inspection and Gaging Tools. Basic principles of gaging. Gage maker tolerances. Gage tolerances

Inspection. 9. Inspection and Gaging Tools. Basic principles of gaging. Gage maker tolerances. Gage tolerances Inspection Nominal dimension 9. Inspection and Gaging Tools Nageswara Rao Posinasetti Tolerance Use Appearance Cost Datum or Reference 1 2 Basic principles of gaging Measurement Measuring can be defined

More information

Your Global Partner for Quality Tools

Your Global Partner for Quality Tools Your Global Partner for Quality Tools Fe Powertools bv A. van Leeuwenhoekweg 36-B9 2408 AN Alphen aan den Rijn The Netherlands T +31 (0)172 47 47 27 F +31 (0)172 47 29 49 E info@fepowertools.com I www.fepowertools.com

More information

Precision made in Europe. As per DIN 8606. The heart of a system, versatile and expandable.

Precision made in Europe. As per DIN 8606. The heart of a system, versatile and expandable. 1 von 9 Precision made in Europe. As per DIN 8606. The heart of a system, versatile and expandable. Main switch with auto-start protection and emergency off. Precision lathe chuck as per DIN 6386 (Ø 100mm).

More information

Standard Scales SERIES 182 Made of Low Expansion Glass. Working Standard Scales SERIES 182 E-32 FEATURES DIMENSIONS SPECIFICATIONS FEATURES DIMENSIONS

Standard Scales SERIES 182 Made of Low Expansion Glass. Working Standard Scales SERIES 182 E-32 FEATURES DIMENSIONS SPECIFICATIONS FEATURES DIMENSIONS Standard Scales SERIES 182 Made of Low Expansion Glass under Mitutoyo s leading-edge Linear Scale production technology. a standard for calibrating graduated scales. 182-502-50 182-501-50 Accuracy (at

More information

No No No

No No No Workshop files pictograms and their meaning Angle grinders Bench grinder/polishing machine Off-hand grinding Band filing machine Eccentric grinders Flexible drive shaft Straight grinders Orbital sanders

More information

DESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4

DESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4 DESCRIPTION PAGE B7 Studs and Nuts Stud Bolts for Pressure-Temperature Piping 2-1 General Purpose End-to-End Studs 2-2 Tap End Stud Bolts 2-3 Double End Stud Bolts 2-4 Sigma Fasteners, Inc. Section 2 STUD

More information

ANSI APPROVED 04/11/2014 ANSI APPROVED 08/17/2011. 45 Reaffirmation ANSI APPROVED 02/28/2014. 45 Reaffirmation ANSI APPROVED 05/06/2013

ANSI APPROVED 04/11/2014 ANSI APPROVED 08/17/2011. 45 Reaffirmation ANSI APPROVED 02/28/2014. 45 Reaffirmation ANSI APPROVED 05/06/2013 STANDARDS STATUS REPORT As of November 4, 2015 Note: Dates in RED indicate the last action taken; Highlighted Items Indicate New/Open Items; Grey items have been closed Document TC Status Comments ASME

More information

Catalogue Measuring instruments and tools

Catalogue Measuring instruments and tools Catalogue Measuring instruents 9/2010 Contents Rules, straight edges, surface plates... pgs 2 Gauges, agnifying glasses, protractors... pgs 6 Stands, indicators, support props... pgs 10 Fir joint calipers,

More information

Format Tools. Professional quality, professional service

Format Tools. Professional quality, professional service Format Tools Professional quality, professional service threading HSS Metric Coarse Hand Tap Sets DIN 352 ISO 2 6H Size Taper Tap Second Tap Plug Tap 3pc Set M3 W90A-16000030 W90A-16010030 W90A-16030030

More information

Chapter 42 Thread and Gear Manufacturing THREAD MANUFACTURING SCREW THREAD STANDARDS 10/16/2014. MET Manufacturing Processes.

Chapter 42 Thread and Gear Manufacturing THREAD MANUFACTURING SCREW THREAD STANDARDS 10/16/2014. MET Manufacturing Processes. MET 33800 Manufacturing Processes Chapter 42 Thread and Gear Manufacturing Before you begin: Turn on the sound on your computer. There is audio to accompany this presentation. THREAD MANUFACTURING Screw

More information

CHISELS / PUNCHES. Innovation is our mission!

CHISELS / PUNCHES. Innovation is our mission! CHISELS / PUNCHES Innovation is our mission! 1 PAGE FLAT CHISELS 680 TILER S FLAT CHISELS 681 SLITTING CHISEL 681 JOINTING CHISELS 681 BRICKLAYERS CHISEL 682 POINTED CHISELS 682 ELECTRICIANS CHISEL 682-683

More information

Working Drawing and Assemblies. Chapter 10

Working Drawing and Assemblies. Chapter 10 Working Drawing and Assemblies Chapter 10 Objectives 1.Define working drawings. 2. Describe how working drawings are used in industry. 3. List the major components of a complete set of working drawings.

More information

Structural Tubes GENERAL INFORMATION...2 ORNAMENTAL ROUND TUBE...3 STRUCTURAL SQUARE TUBE...4 STRUCTURAL RECTANGULAR TUBE SPECIFICATIONS...

Structural Tubes GENERAL INFORMATION...2 ORNAMENTAL ROUND TUBE...3 STRUCTURAL SQUARE TUBE...4 STRUCTURAL RECTANGULAR TUBE SPECIFICATIONS... Structural Tubes GENERAL INFORMATION...2 ORNAMENTAL ROUND TUBE...3 STRUCTURAL SQUARE TUBE...4 STRUCTURAL RECTANGULAR TUBE...5-6 SPECIFICATIONS...7-9 1 STAINLESS STEEL ORNAMENTAL / STRUCTURAL TUBING Standard

More information

Data Sheet: LDS 1363 Date:

Data Sheet: LDS 1363 Date: Product: Mechanical Vernier Measuring Sets Page 1 of 5 This set contains a selection of measuring tools most suitable for students and apprentices Set contents: Metric Set: 50-600-025 Fine Adjustment Vernier

More information

EVEN FOR SMALL QUANTITIES WE GET STARTED RIGHT AWAY...

EVEN FOR SMALL QUANTITIES WE GET STARTED RIGHT AWAY... EVEN FOR SMALL QUANTITIES WE GET STARTED RIGHT AWAY... Because we produce in-house, so we don t have far to go. Our decisions are not based on when and who can do what in Asia; instead, we look at what

More information

Machine Tool Practices, 8th Edition 2006 Correlated to: South Carolina Manufacturing Course Standards for Machine Technology 1, 2, 3, 4

Machine Tool Practices, 8th Edition 2006 Correlated to: South Carolina Manufacturing Course Standards for Machine Technology 1, 2, 3, 4 62300100 A. PERFORMING WORK SAFETY PRACTICES 62300101 Demonstrate the ability to work safely. SE: p.6-13, 208-210, 233-235 TE: Manual p.11-12, 51-52, 55-58 TECH: CD Shop Safety: PowerPoint Slides 1-8 62300102

More information

HOT ROLLED ELECTRIC RESISTANCE WELDED (HREW) ROUND TUBING - ASTM A513 TYPE 1 Diameter Tolerances (inches)

HOT ROLLED ELECTRIC RESISTANCE WELDED (HREW) ROUND TUBING - ASTM A513 TYPE 1 Diameter Tolerances (inches) HOT ROLLED ELECTRIC RESISTANCE WELDED (HREW) ROUND TUBING - ASTM A513 TYPE 1 Diameter Tolerances (inches) NOTE: Measurements for diameter are to be taken at least 2 inches (a) from the ends of the tubes

More information

3. What part of the lathe regulates the feed rate of the cutting tool? The quick-change gear box.

3. What part of the lathe regulates the feed rate of the cutting tool? The quick-change gear box. Section 5, Unit 1 1. List the four main parts of the engine lathe. The four main sections of the lathe are the bed, the headstock, the tailstock, and the carriage. 2. What are the two main purposes of

More information

Centring, Drilling, Counterboring and Countersinking, Reaming and Tapping on the Drilling Machines Course: Techniques for Machining of Material.

Centring, Drilling, Counterboring and Countersinking, Reaming and Tapping on the Drilling Machines Course: Techniques for Machining of Material. Centring, Drilling, Counterboring and Countersinking, Reaming and Tapping on the Drilling Machines Course: Techniques for Machining of Material. Instruction Examples for Practical Vocational Training Table

More information

Understanding Threads and Fasteners. There are three basic applications for screw threads:

Understanding Threads and Fasteners. There are three basic applications for screw threads: Understanding Threads and Fasteners There are three basic applications for screw threads: To hold parts together To provide for adjustment between parts To transmit power 1 Screw Thread Terms Screw Thread

More information

ANSI/ASME B36.19M-1985 ANSI/ASME B36.10M-1995 ISO 4200: 1991(E) unit length (presented with ISO 4200 data)

ANSI/ASME B36.19M-1985 ANSI/ASME B36.10M-1995 ISO 4200: 1991(E) unit length (presented with ISO 4200 data) Section 5 Pipe and Tube Sizes This Section contains pipe and tube dimensions and weights, and information on specific applications. (Pipe threads and surface finishes are covered in Section 10. Weld bevels

More information

Pipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).

Pipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant). Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)

More information

STANDARD TAPERS 906 STANDARD TAPERS

STANDARD TAPERS 906 STANDARD TAPERS 906 STNDRD TPERS STNDRD TPERS Standard s Certain types small tools and machine parts, such as twist drills, end mills, arbors, lathe centers, etc., are provided with taper shanks which fit into spindles

More information

BZP Tensile Class 8 Stainless Steel A2 Height (m) in mm A/F (sw) in mm Art. No.

BZP Tensile Class 8 Stainless Steel A2 Height (m) in mm A/F (sw) in mm Art. No. Hexagon Nuts Full nut with metric coarse thread. Available in the following materials: Steel, Bright Zinc Plated. Din 934-8 Steel, Self Colour. Din 934-10. Stainless Steel; A2-70. Din 934. Also available

More information

Section 7. Socket Weld and Threaded Fittings. Socket Weld and Threaded Fittings 7-1

Section 7. Socket Weld and Threaded Fittings. Socket Weld and Threaded Fittings 7-1 Section 7 Socket Weld and Threaded Fittings This Section contains dimension and tolerance information extracted from American and British specifications applicable to socket weld and threaded fittings.

More information

Gaging & Inspection Tool Design

Gaging & Inspection Tool Design Training Objective After watching the program and reviewing this printed material, the viewer will understand the basic aspects of gaging and inspection tool device design. The various gaging tools are

More information

TOOL POSTS WITH TOOL HOLDERS MACHINE SHOP USE

TOOL POSTS WITH TOOL HOLDERS MACHINE SHOP USE PDF processed with CutePDF evaluation edition www.cutepdf.com TOOL POSTS WITH TOOL HOLDERS MACHINE SHOP USE Tool Post Tool Holder Tool Post Wedge Tool Post Ring FRONT Tool Post Tool Holder Tool Post Wedge

More information

KIRÁLY TRADING KFT H-1151 Budapest Mogyoród útja 12-14 tel: 061307-3801 Email_pzoli@kiralytrading.hu. Clamps Clamping devices

KIRÁLY TRADING KFT H-1151 Budapest Mogyoród útja 12-14 tel: 061307-3801 Email_pzoli@kiralytrading.hu. Clamps Clamping devices 04000 Clamps Clamping devices 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 297 04010 Adjustable straps Tempered steel 1.1191 Black oxide finish nlm 04010-101 Suitable thrust

More information

TOOL WEAR, TOOL LIFE, HAND TOOLS AND MACHINE TOOLS. 1

TOOL WEAR, TOOL LIFE, HAND TOOLS AND MACHINE TOOLS.   1 TOOL WEAR, TOOL LIFE, HAND TOOLS AND MACHINE TOOLS email: vkjain@iitk.ac.in 1 PROCESS OF CUTTING TOOL FAILURE Cutting Tool Failure Mechanisms: 1. By Plastic deformation 2. By chipping due to mechanical

More information

Bore Gages SERIES 511 for Small Holes

Bore Gages SERIES 511 for Small Holes Bore Gages SERIES 511 for Small Holes Its interchangeable anvils are made of alloyed steel. The dial indicator is fully protected by a rugged cover. Metric Gage Stem ø 8mm Without Dial Gage With 206SB

More information

Bore Gages SERIES 511 for Small Holes

Bore Gages SERIES 511 for Small Holes Bore Gages SERIES 511 for Small Holes Without Dial Gage With 206SB Graduation 0.01mm With 2109SB-10 Graduation 0.001mm of s 6-10mm 511-209* 511-211 511-210 9 1 10-18.5mm 511-201* 511-20 511-203 9 1 ( 21DZA000

More information

Service is our #1 priority and customer satisfaction is achieved through:

Service is our #1 priority and customer satisfaction is achieved through: CATALOGUE Our mission at Fisher Metrology is to provide top quality gauges, at competitive prices with the best delivery possible. We represent, and purchase products from premier gaugemakers in the U.S.A.

More information

CUTTING TOOLS FOR MACHINE SHOP USE

CUTTING TOOLS FOR MACHINE SHOP USE CUTTING TOOLS FOR MACHINE SHOP USE WORK HOLDING TOOLS, CUTTING TOOLS AND SHOP ACCESSORIES T-Slot Bolts Nuts and Washers Set-up Wedges 14 FRONT SIDE WORK HOLDING TOOLS MACHINE SHOP USE Nut Washer T-Slot

More information

OD 1401 9 PRECISION MEASURING INSTRUMENTS

OD 1401 9 PRECISION MEASURING INSTRUMENTS SUBCOURSE EDITION OD 1401 9 PRECISION MEASURING INSTRUMENTS PRECISION MEASURING INSTRUMENTS SUBCOURSE OD1401 EDITION 9 Unites States Army Combined Arms Support Command Fort Lee, VA 23801-1809 5 CREDIT

More information

Hose and Tube Fittings Series 1-3

Hose and Tube Fittings Series 1-3 Embracing Challenge Hose and Tube Fittings Series 1-3 out of plastics PP, PVDF, PTFE Series 1 Special Features Corrosion resistant Gas tight Easy to handle Different connection threads Application Hose

More information

SPRING LOADED DEVICES

SPRING LOADED DEVICES Spring Loaded Devices SPRING LOADED DE VICES Plungers: Plungers, Spring...36 37 Plungers, Spring, Metric...38 39 Plungers, Shortie Spring... 40 Plungers, Shortie Spring Stainless Steel... 40 Plungers,

More information

Carbon. Stainless. We have you covered >TUBING >PIPE >BAR >TUBING >PIPE >FITTINGS >FLANGES >BAR

Carbon. Stainless. We have you covered >TUBING >PIPE >BAR >TUBING >PIPE >FITTINGS >FLANGES >BAR Carbon or Stainless Carbon >TUBING >PIPE >BAR Alloy Stainless Steel Aluminum >TUBING >PIPE >FITTINGS >FLANGES >BAR We have you covered www.mkcanada.com www.specialtysteels.com Looking for Carbon tubing,

More information

BS 4504 Circular Flanges - General

BS 4504 Circular Flanges - General BS 4 Circular Flanges - General British Standard BS 4 : Section 3.1 : 1989 - Circular Flanges for Pipes, Valves and Fittings ( Designated), Specification for Steel Flanges. This covers flanges in nominal

More information

ISO metric black hexagon bolts, screws and nuts Specification

ISO metric black hexagon bolts, screws and nuts Specification BRITISH STANDARD BS 4190:2001 ISO metric black hexagon bolts, screws and nuts Specification ICS 21.060.10; 21.060.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Committees responsible

More information

Using a Caliper. The First Step. Four Basic Readings

Using a Caliper. The First Step. Four Basic Readings The premier source of parts and accessories for mini lathes and mini mills. Using a Caliper A caliper has two jaws, one fixed, the other sliding. Move the sliding jaw by pressing your thumb on the bump

More information

Acorn nuts economic type Blanked common plain washers. Blind rivets Cage nuts Cheese head rivets

Acorn nuts economic type Blanked common plain washers. Blind rivets Cage nuts Cheese head rivets UNI ISO "T" slot hammer head 5533 - - - - "T" slot nuts 5531 - - - - "T" slot square head Acorn nuts (domed cap nuts) 5532 - - - - 5721 1587 - - - Acorn nuts economic type Blanked common plain washers

More information

THIS PAGE INTENTIONALLY LEFT BLANK

THIS PAGE INTENTIONALLY LEFT BLANK (713) 690-0040 THIS PAGE INTENTIONALLY LEFT BLANK ORIFICE FLANGES In Carbon, Alloy and Stainless 300lb. through 2500 lb. or Ring Joint ORIFICE FLANGES are widely used in conjunction with orifice meters

More information

This is a picture of both the 3/8 inch and ¼ inch broaches, the long thin sleeve is the sleeve I made from drill rod for the C type broaches to cut

This is a picture of both the 3/8 inch and ¼ inch broaches, the long thin sleeve is the sleeve I made from drill rod for the C type broaches to cut This is a picture of both the 3/8 inch and ¼ inch broaches, the long thin sleeve is the sleeve I made from drill rod for the C type broaches to cut the bolt guide slot (1/4 inch broach) and start the raceways.

More information

Oscillating Steam Engine Building Tips

Oscillating Steam Engine Building Tips The premier source of tooling, parts, and accessories for bench top machinists. Oscillating Steam Engine Building Tips While we can t provide a complete course on machining, this document provides some

More information

SEAMLESS WELDED FITTINGS

SEAMLESS WELDED FITTINGS SEAMLESS WELDED FITTINGS WALL THICKNESS NPS Pipe 2 A B K D V E F G O.D. Light SCH SCH STD SCH SCH X-SIG SCH SCH SCH SCH SCH XX NPS Wall 20 0 40 60 80 00 20 40 60 Stg ASA MSS /2.840.08 --- ---.09.09 ---.4.4

More information

Provided by Productivity Quality Inc s Metrology Toolbox

Provided by Productivity Quality Inc s Metrology Toolbox Plug gaging of holes by the GO-NOGO method By Van Keuren Introduction Introduction The American National Standards Institute defines a gage as "a device for determining whether or not one or more dimensions

More information

Thread and End Connection

Thread and End Connection www.swagelok.com and End Connection Identification Guide 2 Contents Introduction and End Connection Terminology.. 4 General Terminology... 5 Step-by-Step Identification Procedure for s and End Connections...

More information

On lathes, screwcutting is

On lathes, screwcutting is Universal Cutting on a Mini Lathe Neil Wyatt looks at screwcutting on a modern lathe. Sooner or later, all model engineers need to cut threads on their lathe. Either the thread is simply too large for

More information

Measurement. Chapter 4

Measurement. Chapter 4 Chapter 4 Measurement LEARNING OBJECTIVES After studying this chapter, students will be able to: Measure to 1/64 (0.5 mm) with a steel rule. Measure to 0.0001 (0.002 mm) using a Vernier micrometer caliper.

More information

Manufacturing Technician Training

Manufacturing Technician Training Mike McKinney / Jefferson College I. Objective: Developed to meet the industry demands and provide an six-week certification program to fast track individuals to secure a position in the manufacturing

More information

Fasteners and screw threads

Fasteners and screw threads ISO Standards Handbook: Fasteners and screw threads Volume 2: Product standards Contents Part 3 : Product standards 2001, Ed. 5, 1094 p., ISBN 92-67-10345-8 3.1 External drive hexagon head bolts and screws

More information

DMS 680. Universal length measuring system gauge inspection for»iso 9000«requirements

DMS 680. Universal length measuring system gauge inspection for»iso 9000«requirements DMS 680 Universal length measuring system gauge inspection for»iso 9000«requirements Universal length measuring system DMS 680 Wide range of applications For periodic inspection of gauges, reference gauges,

More information

Index. Metric Hex Head Fasteners. Metric Socket Head Fasteners. Metric Threaded Rod. Metric Nuts :Metric Hex Nuts :Metric Weld Nuts :Metric Shaft Nuts

Index. Metric Hex Head Fasteners. Metric Socket Head Fasteners. Metric Threaded Rod. Metric Nuts :Metric Hex Nuts :Metric Weld Nuts :Metric Shaft Nuts Index Section A Metric Hex Head Fasteners Section B Metric Socket Head Fasteners Section C Metric Threaded Rod Section D Section E Section F Metric Nuts :Metric Hex Nuts :Metric Weld Nuts :Metric Shaft

More information

Because of the many types of drilling tools and methods, the tool choice is determined by a number of factors, including:

Because of the many types of drilling tools and methods, the tool choice is determined by a number of factors, including: Training Objective After watching the program and reviewing this printed material, the viewer will gain knowledge and understanding of the basics of the drills and machines used in a variety of holemaking

More information

Measuring pin catalogue. Measuring pins Measuring pin sets Storage cases Test Certificates Magnetic measuring pins

Measuring pin catalogue. Measuring pins Measuring pin sets Storage cases Test Certificates Magnetic measuring pins 2006 Measuring pin catalogue Measuring pins Measuring pin sets Storage cases Test Certificates Magnetic measuring pins PRECISION STANDARD TOOLS PINNING SYSTEMS DREI-S-technologies MEASURING PINS Linearity

More information

Screw Thread Design. Rev. 3-4-09

Screw Thread Design. Rev. 3-4-09 Screw Thread Design Screw Thread Fundamentals A screw thread is defined as a ridge of uniform section in the form of a helix on either the external or internal surface of a cylinder. Internal threads refer

More information

How to Use This Booklet

How to Use This Booklet Accurate identification of ports and connectors in fluid piping systems is necessary before the correct hose or tube assembly can be selected and installed. With this booklet and a few simple tools, measurement

More information

Slide 1. Slide 2 CHAPTER -3 LIMITS, FITS & TOLERANCE IMPORTANT TERMS

Slide 1. Slide 2 CHAPTER -3 LIMITS, FITS & TOLERANCE IMPORTANT TERMS Slide 1 CHAPTER -3 LIMITS, FITS & TOLERANCE 1 Slide 2 IMPORTANT TERMS ACCURACY: Capability to get accurate measure of dimension (Micrometer & Scale) accurate upto one millionth of metre(micron) PRECISION

More information

WÜRTH Industrie Service. Fasteners. Differences between DIN EN ISO standards

WÜRTH Industrie Service. Fasteners. Differences between DIN EN ISO standards WÜRTH Industrie Service Fasteners Differences between DIN EN standards Content Introduction 4 1. Product descriptions and product changes 5 2. Standardization 5 2.1 DIN 5 2.2 5 2.3 EN 5 3. Small slotted

More information

IPE 381 Chapter:10 Gauges and Gauge Design

IPE 381 Chapter:10 Gauges and Gauge Design IPE 381 Chapter:10 Gauges and Gauge Design Abdullah-Al-Mamun Lecturer, Dept. of IPE Outline Basics of Gauges Classification of Gauges Gauge Design Screw Gauges Adv & Disadv of Limit Gauges Gauge Design

More information

Worms and wheels Gears Pulleys Chain sprockets Racks Screw jacks Ball screws Lead screws Gearboxes Springs

Worms and wheels Gears Pulleys Chain sprockets Racks Screw jacks Ball screws Lead screws Gearboxes Springs Worms and wheels Gears Pulleys Chain sprockets Racks Screw jacks Ball screws Lead screws Gearboxes Springs Linear shafts Shock absorbers Ball pins Hand wheels Universal joints Couplings Screws and fasteners

More information

testing and measuring instruments for vehicle wheels

testing and measuring instruments for vehicle wheels testing and measuring instruments for vehicle wheels en testing and measuring instruments for vehicle wheels For more than 20 years MAKRA has been manufacturing measuring and testing equipment for the

More information

3000, 4000, 4100, 7500, 7700

3000, 4000, 4100, 7500, 7700 3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes s Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the

More information

Spray Guns Cup Systems Breathing Protection Filter Technology Accessories. Spray Guns

Spray Guns Cup Systems Breathing Protection Filter Technology Accessories. Spray Guns Spray Guns SATAjet 5000 B RP /HVLP SATAjet 5000 B RP (DIGITAL) www.sata.com/satajet5000b Inlet pressure Field of application: 0.5 bar 2.4 bar Compliant: max. 2.0 bar Air consumption at 2.0 bar: 290 Nl/min

More information

It's large enough to handle most welding job shop projects, yet small enough to make it a worth while home-workshop tool

It's large enough to handle most welding job shop projects, yet small enough to make it a worth while home-workshop tool It's large enough to handle most welding job shop projects, yet small enough to make it a worth while home-workshop tool H Craft Print Project No. 272 ERE'S a metal bender that will enable you to bend

More information

Forged High Pressure Pipe Fittings

Forged High Pressure Pipe Fittings Forged High Pressure Pipe Fittings Forged High Pressure Pipe Fittings Summary : Type 1. Elbow, Tee, Cross, Coupling, Half Coupling, Cap, Plug, Bushing, Union, HEX. Nipple, Swage nipple, Bull Plug, Street

More information

Bore Gages SERIES 526 for Extra Small Holes

Bore Gages SERIES 526 for Extra Small Holes Bore Gages SERIES 526 for Extra Small Holes These gages are designed to measure the diameters of small holes. The radial displacement of the split-ball anvil is converted to axial displacement of the measuring

More information

ACCESSORIES FOR TURNING

ACCESSORIES FOR TURNING ACCESSORIES FOR TURNING Accessories for turning D140 D180 D210 D240 D250 D280 D320 D330 D360 D420 D460 D560 Plane clamping disk Ø 170 mm 344 0295 Plane clamping disk Ø 200 mm 344 0352 Plane clamping disk

More information

SPARE PARTS FOR CONSTRUCTION MACHINERY CONCRETE PUMPS, TRUCK MIXERS & BATCHING PLANTS

SPARE PARTS FOR CONSTRUCTION MACHINERY CONCRETE PUMPS, TRUCK MIXERS & BATCHING PLANTS components, accessories, spare parts for construction machineries SPARE PARTS FOR CONSTRUCTION MACHINERY CONCRETE PUMPS, TRUCK MIXERS & BATCHING PLANTS INTRODUCTION We are pleased to introduce our product

More information

VCE VET ENGINEERING STUDIES

VCE VET ENGINEERING STUDIES Victorian Certificate of Education 2013 SUPERVISOR TO ATTACH PROCESSING LABEL HERE STUDENT NUMBER Letter Figures Words VCE VET ENGINEERING STUDIES Written examination Section Wednesday 20 November 2013

More information

CONTENTS DESCRIPTION PAGE DESCRIPTION PAGE

CONTENTS DESCRIPTION PAGE DESCRIPTION PAGE 2014 Catalog THE ABC S OF PLUG GAGES, GAGE MAKER S TOLERANCE CHART... 4 CONTENTS DESCRIPTION PAGE DESCRIPTION PAGE TAPERLOCK STYLE GAGES... 24 PLUG GAGE USE, PLUG GAGE TOLERANCE & SELECTION... 5 CALIBRATION

More information

AISI CHEMICAL COMPOSITION LIMITS: Nonresulphurized Carbon Steels

AISI CHEMICAL COMPOSITION LIMITS: Nonresulphurized Carbon Steels AISI CHEMICAL COMPOSITION LIMITS: Nonresulphurized Carbon Steels AISI No. 1008 1010 1012 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 10 1026 1027 1029 10 1035 1036 1037 1038 1039 10 1041 1042 1043

More information

PRECISION MEASUREMENT

PRECISION MEASUREMENT PRECISION MEASUREMENT Table of Contents I. PRECISION MEASUREMENT...1 A. STEEL RULES...1 1. Fractional-Inch Rule...1 Figure 1-1 Rule Divided Into 8ths & 16ths...1 Figure 1-2 Rule Divided Into 32nds & 64ths...2

More information

Lathe Milling Attachment

Lathe Milling Attachment Lathe Milling Attachment By L C. MASON BY CLEVERLY stacking cold-rolled flat stock together, T-slots and slide for this lathe milling attachment are made without costly machinery. In fact, only two tools,

More information

Measurement & Gaging. Training Objective

Measurement & Gaging. Training Objective Training Objective After watching the program and reviewing this printed material, the viewer will learn the basics of measurement and the use of measuring and gaging tools. The concepts of measurements

More information

Pipe Thread Types and Designations

Pipe Thread Types and Designations Pipe Thread Types and Designations Overview: Different types of screw threads have evolved for fastening, and hydraulic systems. Of special concern are plastic-to-metal, taper/parallel threaded joints

More information

LINEAR MOTION CONTROL

LINEAR MOTION CONTROL LINEAR MOTION CONTROL Technical Data Sheet Static Locks RLSS Series Nexen s new generation of linear holding/locking devices take rod locking technology to the next level. With superior performance, these

More information

ipuc p. 70 The big steel shelves with the brass patina became the special challenge in this project.

ipuc p. 70 The big steel shelves with the brass patina became the special challenge in this project. p. 70 ipuc ipuc is a single point system with rectangular sockets in two dimensions and with different load capacities. Both sockets ipuc0 and ipuc25 can be installed into wooden materials and acrylic

More information

DIMENSIONAL BOLTING CATALOG

DIMENSIONAL BOLTING CATALOG DIMENSIONAL BOLTING CATALOG DIMENSIONAL CATALOG Table of Contents Page Screws Round Head Screws 1-1 Various Head Styles Machine Scerws 1-2 to 1-23 Tapping Screws (Approx. Hole Sizes) 1-24 Thumb and Wing

More information

Ultra Live Center RN. Clamping tools for clamping on machine tools. NEIDLEIN revolving ultra live centers type RN ensure: Type RN with morse taper

Ultra Live Center RN. Clamping tools for clamping on machine tools. NEIDLEIN revolving ultra live centers type RN ensure: Type RN with morse taper Ultra Live Center RN Type RN with morse taper NEIDLEIN ultra live centers are designed for employment in turning, grinding and other production machines. Owing to the application of bearing and the stable

More information

COLLEGE OF ENGINEERING AND APPLIED SCIENCE MACHINE SHOP TOOLS AND PRACTICES

COLLEGE OF ENGINEERING AND APPLIED SCIENCE MACHINE SHOP TOOLS AND PRACTICES COLLEGE OF ENGINEERING AND APPLIED SCIENCE MACHINE SHOP TOOLS AND PRACTICES I. OBJECTIVE To provide an overview and basic knowledge of the University of Wyoming, College of Engineering, equipment, tools,

More information

Stainless Steel Pipe and Flanges

Stainless Steel Pipe and Flanges Stainless Steel Pipe and Flanges Stainless Steel 4 Pipe and Flanges Photography courtesy of Outokumpu, Arcelor, Atlas Steels and New Zealand Tube Mills. Stainless steel pipe and fittings A stainless steel

More information

Students have little or no previous knowledge or skill in the material being covered.

Students have little or no previous knowledge or skill in the material being covered. Description This Activity Plan will enable students to identify the differences between metric and imperial bolts (cap screws). They will learn how to measure a bolt and determine the thread type by using

More information

THRUST NEEDLE ROLLER AND CAGE ASSEMBLIES Assembly Dimensions, Load Ratings, Thrust Washer and Piloting Dimensions... 480-487

THRUST NEEDLE ROLLER AND CAGE ASSEMBLIES Assembly Dimensions, Load Ratings, Thrust Washer and Piloting Dimensions... 480-487 Thrust Bearings Page Nomenclature............................................ 474 Introduction............................................. 476 Identification.............................................

More information

Dimensions for Forged Steel Flanges

Dimensions for Forged Steel Flanges 150 lb Flanges Length Through Hub Bore Drilling Nominal Pipe Size Outside Thickness of of Flange Flange ( O ) ( C ) of Raised Face ( R ) of Hub at Base (Note 1) ( X ) Hub Beginning of Chamfer Neck ( A

More information

Semi-automatic thread-cutting machines

Semi-automatic thread-cutting machines Semi-automatic thread-cutting machines REMS Unimat for Professionals High operating efficiency Piece and series production Easy to operate Short changeover times Bolts Pipes Rebar Metric bolt threads Straight

More information

Lecture Slides. Chapter 8. Screws, Fasteners, and the Design of Nonpermanent Joints

Lecture Slides. Chapter 8. Screws, Fasteners, and the Design of Nonpermanent Joints Lecture Slides Chapter 8 Screws, Fasteners, and the Design of Nonpermanent Joints The McGraw-Hill Companies 2012 Chapter Outline Reasons for Non-permanent Fasteners Field assembly Disassembly Maintenance

More information

FAG Hydraulic nuts. Technical Product Information

FAG Hydraulic nuts. Technical Product Information FAG Hydraulic nuts Technical Product Information Contents Application 2 Design 2 Design variants 3 Pressure generators, connectors 4 Dimension tables for FAG hydraulic nuts (metric) 6 Dimension tables

More information

DTU Animal Cart Programme

DTU Animal Cart Programme DTU Animal Cart Programme TECHNICAL 21 RELEASE PIPE AND ROLLER DONKEY CART AXLES Development Technology Unit, Department of Engineering, University of Warwick, Coventry, CV4 7AL UK, tel: +44 (0)1203 523523

More information

Spectifications. ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers)

Spectifications. ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) Spectifications ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) ANSI / ASME B1.20.1 ASME B16.10 ASME B16.11 ASME B16.25 ANSI / ASME B16.28 ANSI / ASME B16.34

More information

RICO TOOL. A Division of HTC (Hot Tool & Cutter Mfg.) 60 Years of Service A MANUFACTURER OF HSS & SOLID CARBIDE CUTTING TOOLS

RICO TOOL. A Division of HTC (Hot Tool & Cutter Mfg.) 60 Years of Service A MANUFACTURER OF HSS & SOLID CARBIDE CUTTING TOOLS 2009 Distributor Price List RICO A Division of HTC (Hot Tool & Cutter Mfg.) 60 Years of Service 1949-2009 A MANUFACTURER OF HSS & SOLID CARBIDE CUTTING S 100% Mfg. In U.S.A. General Information..................................

More information

Technical Product Specification (TPS)

Technical Product Specification (TPS) ISO Standards collection Technical Product Specification (TPS) Contents ISO 1:2002 Geometrical Product Specifications (GPS) -- Standard reference temperature for geometrical product specification and verification

More information

10. Riveting Rivet types Solid rivets Solid rivets are used less and less. They have been replaced in many cases by welding or bonding.

10. Riveting Rivet types Solid rivets Solid rivets are used less and less. They have been replaced in many cases by welding or bonding. . Riveting.1 Rivet types.1.1 Solid rivets Solid rivets are used less and less. They have been replaced in many cases by welding or bonding. Because of the large countersinking angle of 140 flat countersunk

More information

Cam Followers (Stud Type Track Rollers) Roller Followers (Yoke Type Track Rollers)

Cam Followers (Stud Type Track Rollers) Roller Followers (Yoke Type Track Rollers) am Followers (Stud Type Track Rollers) Roller Followers (Yoke Type Track Rollers) High-quality products with long life and proven reliability. These series of cam followers and roller followers significantly

More information