Installation Guide for the Model FA310TX Fast Ethernet PCI Adapter

Transcription

1 Installation Guide for the Model FA310TX Fast Ethernet PCI Adapter NETGEAR, Inc. A Bay Networks Company Warm Springs Blvd. Fremont, CA USA M-FA310-0 November 1996

2 1996 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR and Bay Networks are trademarks of Bay Networks, Inc. Other brand and product names are registered trademarks or trademarks of their respective holders. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense. EN Declaration of Conformance This is to certify that the NETGEAR Model FA310TX Fast Ethernet PCI Adapter is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN Class B (CISPR 22). Compliance is dependent upon the use of shielded data cables. Bestätigung des Herstellers/Importeurs Es wird hiermit bestätigt, daß das NETGEAR Model FA310TX Fast Ethernet PCI Adapter gemäß der im BMPT-AmtsblVfg 243/1991 und Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschriftsmäßige Betreiben einiger Geräte (z.b. Testsender) kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung. ii

3 Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen. Die Erfüllung der zutreffenden Vorschriften hängt von der Benutzung geschirmter Kabel ab. Der Benutzer ist für den Erwerb der entsprechenden Kabel verantwortlich. Certificate of the Manufacturer/Importer It is hereby certified that the NETGEAR Model FA310TX Fast Ethernet PCI Adapter has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the notes in the operating instructions. Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for compliance with the regulations. Compliance with the applicable regulations is dependent upon the use of shielded cables. It is the responsibility of the user to procure the appropriate cables. Voluntary Control Council for Interference (VCCI) Statement This equipment is in the first category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing Equipment and Electronic Office Machines that are aimed at preventing radio interference in commercial and/or industrial areas. Consequently, when this equipment is used in a residential area or in an adjacent area thereto, radio interference may be caused to equipment such as radios and TV receivers. Compliance is dependent upon the use of shielded AC power cables. The user is responsible for procuring the appropriate cables. Read instructions for correct handling. iii

4 Customer Support For assistance with installing and configuring your NETGEAR system or with post-installation questions or problems, contact your point of purchase representative. To contact customer support or to purchase additional copies of this document and publications for other NETGEAR products, you can contact NETGEAR at the following numbers: Phone: U.S./Canada: Japan: Germany: Fax: U.S./Canada: World Wide Web NETGEAR maintains a World Wide Web Home Page that you can access at the universal resource locator (URL) A direct connection to the Internet and a Web browser such as Mosaic or Netscape are required. Bulletin Board Service NETGEAR maintains a bulletin board that you can access to obtain the latest versions of the software drivers. You can contact the bulletin board service at the following number: Phone: U.S.: iv

5 Contents Chapter 1 Introduction Overview Features System Requirements Chapter 2 Installation Package Contents Physical Description Installing the Adapter in a Computer Connecting to 10/100 Mbps Network Cables Completing and Verifying Installation Installing Software Drivers Installing the Novell NetWare Client Driver for DOS Installing the Windows 95 Network Driver Installing Other Software Drivers Chapter 3 Diagnostics Using the Diagnostics Program Diagnostics Failure Troubleshooting Contents v

6 Appendix A Technical Specifications General Specifications... A-1 Index Contents vi

7 Figures Figure 2-1. Model FA310TX adapter Figure 2-2. Connecting to network cables Figure 3-1. Select Adapter Menu Figure 3-2. Your Current Configuration screen Table Table 2-1. LED descriptions Figures vii

8

9 Chapter 1 Introduction Congratulations on your purchase of the NETGEAR Model FA310TX Fast Ethernet PCI Adapter, a 32-bit Fast Ethernet adapter card. The Model FA310TX adapter has been developed by combining the latest 100BASE-TX Ethernet and peripheral component interface (PCI) local bus technology. This guide describes how to install and use the adapter card and how to install the software drivers and diagnostics program. Overview The Model FA310TX adapter runs in bus master mode, directly sending and receiving Ethernet packets to or from the memory, using minimum aid from the central processing unit (CPU). Bus mastering allows a peripheral device to take control of the system bus and not rely on the central processor. Using the greater bandwidth and faster bus speed benefits of PCI bus, the Model FA310TX adapter is superior to a standard AT bus adapter. It uses a high-performance intelligent Ethernet controller that can transmit or receive data at 10 Mbps or 100 Mbps, can directly access the system CPU, and can transfer data directly between I/O devices and system memory in the 32-bit bus master mode. For flexibility, the Model FA310TX adapter comes with one RJ-45 port to support your existing 10BASE-T or the 100BASE-TX Category 5 unshielded twisted pair (UTP) cable. The adapter automatically senses either 10 Mbps or 100 Mbps, and when operating in full-duplex mode, the network speed is doubled to 20 Mbps or 200 Mbps. Introduction 1-1

10 Installation Guide for the Model FA310TX Adapter Features The Model FA310TX adapter, designed to have high performance and to be versatile, supports many network operating systems and has the following features: Is compatible with the Ethernet IEEE BASE-TX, 10BASE-T, and NWay auto-negotiation industry standards. NWay auto-negotiation allows the adapter to automatically select the operating speed of 10 Mbps or 100 Mbps, depending on the hub or switch the adapter is connected to. Supports half- and full-duplex mode that is made possible by NWay auto-negotiation. In full-duplex mode, the adapter can transmit and receive concurrently when the other party also supports full-duplex, providing a transfer rate of up to 200 Mbps. Allows for Plug and Play. You simply insert the Model FA310TX adapter into the PCI slot of a Pentium/486 machine, and the PCI system BIOS automatically configures the adapter. Supports 32-bit PCI Bus Master mode, enabling high throughput and low CPU utilization. Has one-step installation. A graphical interface guides you through the installation of software drivers and support files for all popular network operating systems. Has complete driver support for Windows 95, Windows NT (Versions 3.1 and higher), Windows for Workgroup, Novell NetWare Client for DOS, Novell NetWare Client for OS/2, Novell NetWare Server (Versions 3.11 and higher), SCO OpenServer, SCO UNIX driver, Artisoft LANtastic, and Packet driver. 1-2 Introduction

11 Installation Guide for the Model FA310TX Adapter Has five status LED indicators (to show 10/100 Mbps media speed selection, full- or half-duplex mode, link status, data activity, and data collision). Has a lifetime warranty. System Requirements The NETGEAR Model FA310TX Fast Ethernet PCI Adapter must be used in a PC that has: A PCI expansion slot with bus mastering capability Microsoft DOS, IBM OS/2, or Microsoft Windows 95 operating system Network operating systems such as Novell NetWare or Microsoft Windows NT Introduction 1-3

12

13 Chapter 2 Installation This chapter provides information on: Package contents Physical description Installing the adapter in a computer Connecting to 10/100 Mbps network cables Completing and verifying installation Installing software drivers Package Contents Unpack the contents of the package and verify them against the following list: NETGEAR Model FA310TX Fast Ethernet PCI Adapter One FA310TX Drivers and Diagnostics Disk that includes software drivers and a diagnostic program This installation manual Warranty and Owner Registration Card Installation 2-1

14 Installation Guide for the Model FA310TX Adapter Physical Description As illustrated in Figure 2-1, there are five LEDs on the Model FA310TX adapter that indicate network status. 100M FULL LINK ACT COL 100M FULL LINK ACT COL 107EA Figure 2-1. Model FA310TX adapter Table 2-1 describes the activity of each LED. Table 2-1. LED descriptions Label Color Activity Description 100M Green On Off FULL Green On Off The port is operating at 100 Mbps. The port is operating at 10 Mbps. The port is operating in full-duplex mode. The port is operating in half-duplex mode. LINK Green On The data link between the card and the hub or switch is good. 2-2 Installation

15 Installation Guide for the Model FA310TX Adapter Table 2-1. LED descriptions (continued) Label Color Activity Description ACT Green On There is data being sent through the port COL Yellow Blinking There is data collision on the network. Occasional blinking of the LED is normal on any network. Installing the Adapter in a Computer The Model FA310TX adapter has configuration specifications set in onboard memory and provides installation information to the computer at startup. To install the Model FA310TX adapter, follow these steps: 1. Turn off and unplug your computer. Caution: Place all printed circuit boards on an antistatic mat until you are ready to install them. If you do not have an antistatic mat, wear a discharge leash or touch a grounded metal object to free yourself of static before you handle the board. 2. Remove the cover from your computer. Installation 2-3

16 Installation Guide for the Model FA310TX Adapter 3. Insert the card into any available PCI Bus Master I/O expansion slot. You can see both PCI and ISA expansion slots when you remove the cover. The PCI slots are shorter. Note: Make sure the PCI expansion slot that you have inserted the adapter in supports local bus mastering. 4. Fasten the Model FA310TX adapter to the rear of the computer chassis by tightening the screw. 5. Close the computer cover. 6. Proceed to the next section, Connecting to 10/100 Mbps Network Cables. Connecting to 10/100 Mbps Network Cables The Model FA310TX adapter contains one RJ-45 connector that automatically senses and switches speed based on the type of hub or switch that is connected. This section describes how to connect 10 Mbps and 100 Mbps network cables to the Model FA310TX adapter. Note: You must connect the adapter to the network before loading software drivers. For connecting to a 10 Mbps network, use a Category 3, 4, or 5 UTP cable with an RJ-45 connector on each end. For connecting to a 100 Mbps network, use only Category 5 UTP cables. For connecting to both 10 Mbps or 100 Mbps networks, you must use a straight-through cable. 2-4 Installation

17 1 2 Installation Guide for the Model FA310TX Adapter For connecting to either 10 Mbps or 100 Mbps network cables, follow these steps: 1. Connect one end of the cable to the Model FA310TX adapter. 2. Connect the other end to a hub or switch, using a star topology method as illustrated in Figure 2-2. Figure 2-2 illustrates workstations with the Model FA310TX adapter installed. The workstations are connected to 10 Mbps and 100 Mbps networks through the NETGEAR Model EN516 10BASE-T Ethernet Hub and the NETGEAR Model FE516 Fast Ethernet Hub. Model SW502 Ethernet Switch Model EN516 Ethernet Hub Model FE516 Fast Ethernet Hub Key Users 10 Mbps 100 Mbps Power users Figure 2-2. Connecting to network cables Note: In 10 Mbps and 100 Mbps networks, Ethernet specifications limit the cable length from a computer to a hub or switch to 300 feet (100 m). Installation 2-5

18 Installation Guide for the Model FA310TX Adapter 3. Proceed to Chapter 3, Diagnostics, to verify connections. Completing and Verifying Installation You must run the diagnostics program as described in Chapter 3, Diagnostics, and pass all of the tests to verify the installation. When the installation is completed and verified, you can install the software drivers. Note: The diagnostics program will not run with the software drivers installed. Installing Software Drivers The software drivers enable the Model FA310TX adapter to be used on many different networks and are located on the FA310TX Drivers and Diagnostics Disk that is included in your package. For information on installing software drivers, refer to information provided in this section. When multiple adapters exist on the system, you must repeat the same procedure for each adapter card. The following drivers are included on the FA310TX Drivers and Diagnostics Disk: Microsoft Windows 95 Windows NT (Versions 3.1 and higher) Windows for Workgroup Novell NetWare Client for DOS Client for OS/2 Server (Versions 3.11 and higher) 2-6 Installation

19 SCO UNIX SCO OpenServer SCO UNIX driver Others Artisoft LANtastic Packet driver Installation Guide for the Model FA310TX Adapter Note: It is important that you keep the FA310TX Drivers and Diagnostics Disk. You will need different software drivers when changing the host operating environment or the network operating system. Installing the Novell NetWare Client Driver for DOS This section describes how to install the driver for a Novell NetWare client computer running MS-DOS. Use the Novell NetWare Client Driver for DOS for networking access to a Novell NetWare server. To install the Novell NetWare Client Driver for DOS, follow these steps: 1. Boot the computer under MS-DOS. 2. Insert the Drivers and Diagnostics Disk into Drive A. 3. Type A:\install at the DOS prompt and press the Enter key. The computer starts executing the installation program. 4. Press the Enter key to skip past the welcome screen of the installation program. The Selection window is displayed. Installation 2-7

20 Installation Guide for the Model FA310TX Adapter 5. Select Novell NetWare and press the Enter key. The NOSs window is displayed. 6. Select Novell NetWare DOS Client and press the Enter key. The network operating system configuration is displayed and you are prompted to enter a target path. 7. Type the destination path on the Target Path field and press the Enter key. You are prompted to indicate if you want to modify the existing AUTOEXEC.BAT file. 8. Type Y and press the Enter key. The AUTOEXEC.BAT file is copied to the path you designated. When the copying is complete, you are prompted to indicate if you want to create a new NET.CFG file. 9. Type Y and press the Enter key. You are prompted when copying is complete for the new NET.CFG file. 10. Press the Enter key to exit when the program is finished running. If you are using NetWare client software that comes with Novell NetWare 3.12 and 4.x, follow these steps before rebooting your computer: a. Insert the NetWare Client for DOS and Windows disk in Drive A. You received NetWare Client for DOS and Windows on the CD included with your Novell Network. b. Type A:\Install.EXE at the DOS prompt and press the Enter key to run the NetWare Client Install program. The main menu is displayed. 2-8 Installation

21 Installation Guide for the Model FA310TX Adapter c. Follow the instructions given by the NetWare Client Install program before proceeding to the field that prompts you to select the driver for your network board. d. Press the Enter key. The Network Board window is displayed showing a list of drivers. e. Select OTHER DRIVERS and press the Enter key. The Insert the Driver Disk window is displayed. f. Enter the destination path that you designated in Step 7 and press the Enter key. The Network window is displayed. g. Select NETGEAR FA310TX Fast Ethernet Adapter and press the Enter key. The main menu of the NetWare Client Install program is displayed. h. Start the installation process by following the directions given on the main menu. 11. Reboot your computer. The driver is now installed. Note: To customize other network parameters, such as the frame type, edit the NET.CFG file in the directory where the NetWare client driver is installed. Installation 2-9

22 Installation Guide for the Model FA310TX Adapter Installing the Windows 95 Network Driver This section describes how to install the driver if your computer is running Windows 95. Use the Windows 95 system for networking access to a Microsoft NT server, a Novell NetWare server, or another Windows 95 networked system. To install the Windows 95 Network driver, follow these steps: 1. Boot the computer and start Windows 95. The New Hardware Found window is displayed stating that new hardware is found. Then the Systems Settings Change window is displayed and asks if you want to restart your computer. 2. Click No. The Windows 95 welcome window is displayed. 3. Click Close to exit the Windows 95 screen and view the desktop. 4. Double-click the My Computer icon on the desktop to open the window. 5. Double-click the Control Panel icon to open the window. 6. Double-click the Network icon to open the window. 7. Click PCI Fast Ethernet DECchip Based Adapter from the choices in the Network window. 8. Click Remove to delete the PCI Fast Ethernet DECchip Based Adapter. 9. Click Add to add a software driver and display the Select Network Component Type window. 10. Double-click Adapter from the choices in the Select Network Component Type window to display the Select Network Adapters window Installation

23 Installation Guide for the Model FA310TX Adapter 11. Click Have Disk. 12. Insert the Drivers and Diagnostics Disk in Drive A to display the Install From Disk window. 13. Make sure that Drive A is designated on the prompt line and click OK to display the Select Network Adapters window. A:\ should appear in response to the prompt that asks you where to copy manufacturer s files from. 14. Double-click NETGEAR FA310TX Fast Ethernet PCI Adapter to display the Network window. 15. Click OK to display the Systems Settings Change window. 16. Click Yes in response to the prompt that asks you if you want to restart the system. Installing Other Software Drivers This section describes how to install any software drivers that are included on the Drivers and Diagnostics Disk with the exception of the Windows 95 Network Driver and the Novell NetWare Client Driver for DOS. To install other software drivers, follow these steps: 1. Boot the computer under MS-DOS. 2. Insert the Drivers and Diagnostics Disk into Drive A. 3. Type A:\install at the DOS prompt, and then press the Enter key. The computer starts executing the installation program. 4. Press the Enter key to skip past the welcome screen of the installation program. The Selection window is displayed. Installation 2-11

24 Installation Guide for the Model FA310TX Adapter 5. Select the category of the network operating system you are using and press the Enter key. The NOSs window is displayed. 6. Press the up/down arrow keys to select the network operating system you are using and press the Enter key. The network operating system configuration is displayed and you are prompted to enter a target path. 7. Type the destination path on the Target Path field and press the Enter key. The installation program decompresses the software driver that you selected, copies the program to the target path, and prompts you when copying is complete. 8. Press the Enter key to exit when the program is finished copying. 9. Use a text editor and type README.TXT at the DOS prompt to open a file with information about how to install the driver you have selected into different operating systems Installation

25 Chapter 3 Diagnostics This chapter describes the diagnostics program, which verifies your installation and gives information on troubleshooting the Model FA310TX adapter. Using the Diagnostics Program To verify installation of your Model FA310TX adapter, you must use the diagnostics program before installing any software drivers for your network. You can copy the diagnostics program to any destination path and run the software from that path, or run the software directly from the disk. The diagnostics program operates only with DOS. If you are using Windows 95, you must shut down and restart in the MS-DOS mode. If you have already used the diagnostics program to verify installation and are using the program for troubleshooting, restarting in the MS-DOS mode will unload the drivers that are loaded under Windows 95. To use the diagnostics program to check whether or not the major components operate properly, it is best to have the network cable connected to a hub or switch. The diagnostics program then checks the major components and the network connection. To run the diagnostics program, follow these steps: 1. Type A:\DIAG.EXE at the DOS prompt. Diagnostics 3-1

26 Installation Guide for the Model FA310TX Adapter 2. Press the Enter key to display the main menu, which lists the diagnostic tests performed by the program. 3. Press the Enter key to skip past the main menu and display the Select Adapter Menu. The program detects the number of adapter(s) installed in your system and displays the settings in a sequence, as illustrated in Figure 3-1. Select Adapter Menu CARD NO NODE ID BUS NO SLOT NO I/O IRQ ======= ================= ======= ======= ====== === A H B H 10 Figure 3-1. Select Adapter Menu 4. Move the highlighted menu bar up and down to select the adapter you want to test. 3-2 Diagnostics

27 Installation Guide for the Model FA310TX Adapter 5. Press the Enter key to display the Your Current Configuration screen, as illustrated in Figure 3-2. The program detects the media availability and transmission speed and determines the kind of test items for the chosen adapter. The lower edge of the screen displays the description of the test item. Pressing [F1] at any time will display a pop-up window that shows the details of the highlighted test item. When the diagnostics program starts, the first test item (Serial ROM TEST) is highlighted in the Test Items Setup Menu. The Serial ROM TEST is highlighted while the program proceeds with the test. When the Serial ROM TEST is completed, the program proceeds with the next selected test item. Note: The Twister Layer Internal Loopback Test is available only when the adapter is connected to a 100BASE-TX Fast Ethernet device. The Network Connection Test is available only when your adapter is connected to a switch or hub. Progressive dots represent the duration of each test as it runs. As the diagnostics program completes each test, the Test Results screen is displayed, indicating which tests have passed or failed. You can print the complete report to a printer, or save the report to a disk file. If any of the tests fail, refer to the next section, Diagnostics Failure. When all tests pass, you are ready to install the software drivers. Diagnostics 3-3

28 Installation Guide for the Model FA310TX Adapter Your Current Configuration NODE ID: A BUS MODE: PCI 32-bit Card Type: FA310TX Connector Type: UTP I/O Base Address: 6000H Interrupt Number: 11 Test Items Setup Menu: [x] Serial ROM Test [x] Controller Internal Loopback Test [ ] Twister Layer Internal Loopback Test [x] Network Connection Test Figure 3-2. Your Current Configuration screen 6. Install the software drivers, following the steps in Installing Software Drivers on page 2-6. Diagnostics Failure If any of the diagnostic tests fail, the adapter may not be defective. You might have made incorrect option settings or option settings that conflict with the settings of other boards, or you might have improperly installed the adapter or cables. If any of the diagnostic tests fail, follow these steps: Check the adapter installation to ensure that the card is seated properly in the slot. Check the length and rating of the cable connection. 3-4 Diagnostics

29 Installation Guide for the Model FA310TX Adapter Make sure the PCI slot that the adapter is plugged into is activated. PCI computers allow PCI slots to be activated or deactivated by using the CMOS utility on the computer, or in some cases, a special PCI utility. Please refer to your computer documentation for information about activating PCI slots. Replace the failed adapter with a working adapter and run the diagnostic test again. Install the adapter in another functioning PCI computer and run the tests again. Replace all other PCI adapters from the computer and run the tests again. If the tests pass, the other PCI adapters may be causing contention. If the adapter passes all the tests and there still appears to be a problem, check the cabling and other devices that may affect the network. Troubleshooting If there are any problems with the Model FA310TX adapter after your network and adapter have been operational, follow these steps: 1. Make sure the appropriate driver is loaded. For further information, refer to Installing Software Drivers on page Make sure the proper cable is connected to the adapter port. For further information, refer to Connecting to 10/100 Mbps Network Cables on page 2-4. Diagnostics 3-5

30 Installation Guide for the Model FA310TX Adapter 3. Make sure the hub complies with the adapter specifications, such as 10 Mbps 10BASE-T or 100 Mbps 100BASE-TX. 4. Run the Diagnostics Program, following the procedures in Using the Diagnostics Program on page Diagnostics

31 Appendix A Technical Specifications This appendix provides technical specifications for the NETGEAR Model FA310TX Fast Ethernet PCI Adapter. General Specifications Standards Compatibility IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3i 10BASE-T Ethernet NetWare tested and approved Microsoft Windows, Windows 95, Windows NT compatible PCI Plug and Play compatible Power Operating voltage: +5V +/- 630 ma maximum Physical Specifications Length: 5.7 in (14.4 cm) Height: 3.7 in (9.3 cm) Weight: 22 lb (100 g) Environmental Specifications Operating temperature: 0 C to 55 C Operating humidity: 10% to 90% noncondensing Technical Specifications A-1

32 Installation Guide for the Model FA310TX Adapter Electromagnetic Emissions CE mark, commercial FCC, Part 15, Class B EN (CISPR 22), Class B VCCI Class 2 Canada ICES-003, Class B Interface Options RJ-45 connector for 10BASE-T or 100BASE-T Ethernet interface A-2 Technical Specifications

33 Index Numerics 100M LED 2-2 A ACT LED 2-3 B BBS. See bulletin board service bulletin board service iv bus mastering 1-1 C cable connections, troubleshooting 3-4 Certificate of the Manufacturer iii COL LED 2-3 customer support iv D diagnostics program failing tests of 3-3 Network Connection Test 3-3 pass and fail messages 3-3 Select Adapter Menu 3-2 Serial ROM TEST 3-3 Twister Layer Internal Loopback Test 3-3 using to verify installation 3-1 Your Current Configuration screen 3-2 F FCC statement ii features 1-2 FULL LED 2-2 I installation completing 2-6 connecting to network cables 2-4 in a computer 2-3 Novell NetWare Client driver for DOS 2-7 of software drivers 2-6 troubleshooting 3-4 verifying 2-6 verifying with diagnostics program 3-1 Windows 95 Network driver 2-10 Index 1

34 L LEDs 100M 2-2 ACT 2-3 COL 2-3 description (table) 2-2 FULL 2-2 LINK 2-3 LINK LED 2-3 M mode full-duplex 1-1, 1-2 half-duplex 1-2 N Network Connection Test diagnostics program 3-3 network speed 1-1 Novell NetWare Client driver for DOS, installing 2-7 NWay auto-negotiation 1-2 P package contents 2-1 PCI. See peripheral component interface peripheral component interface, troubleshooting slot 3-4 physical description 2-2 R RJ-45 port 1-1, 2-4 S screens Select Adapter Menu 3-2 Your Current Configuration 3-2 Select Adapter Menu 3-2 Serial ROM TEST 3-3 software drivers 2-6 system requirements 1-3 T technical specifications A-1 troubleshooting adapter installation 3-4 cable connections 3-4 PCI slot 3-4 Twister Layer Internal Loopback Test Index

35 W Windows 95 Network driver installation 2-10 World Wide Web iv Y Your Current Configuration screen 3-2 Index 3

36