E46 Lowering Fitting of Eibach Pro Springs
|
|
- Oswald Tate
- 7 years ago
- Views:
Transcription
1 E46 Lowering Fitting of Eibach Pro Springs Tools needed: Decent socket set (need 16mm, 18mm and 22mm sockets, suitable ratchets and extenders) Breaker Bar Spring Clamps Open ended spanner (17mm) Wire brush New springs! (I fitted Eibach Pro kit to my e sport) Front Struts Firstly, pop the cap off the front strut and crack loose the main strut piston nut don t undo it any great amount yet. A is explained later, don t worry about it now. A Securely jack up and secure the car with the wheel removed. Loosen the 3 top mount nuts again, don t undo at this point. Undo the anti-roll bar drop link top bolt Make sure the spanner is on the metal part of the link, or you ll end up knackering the rubber boot and will need new drop links (which depending on the mileage of you car may not be a bad thing anyway)
2 Remove the drop link from it s hole you might need to pry the anti-roll bar down a bit to allow you to get it out - use your breaker bar on the chassis to do this. Now you need to undo the main strut clamp bolt. This may well be very corroded (mine was), so it may pay you to douse it in WD40 or other penetrating spray and leave it whilst you make a cuppa. Remove the bolt. I cleaned the bolt up with a wire brush to make sure it d be easier to put back in again later. You should now be able to wiggle the strut out of the clamp. Make sure your brake hose isn t stretched too much when doing this. Mine was ok this time on the e46, but on my previous e39 lowering expedition, we had to remove the calliper so as not to damage the hose. Worth keeping an eye on. With the strut freed from the clamp, you can now remove the 3 top mount nuts and remove the entire strut assembly from the car. Times like this I quite like being the one behind the camera!
3 Set the spring clamps onto the strut. Put them on the lowest turn of the spring you can and on the top of the cap - not the top of the top mount. Make sure the spring claps are set as near exactly opposite as possible, then start clamping the spring down. Clamp each side down a bit at a time so that tension is maintained on both clamps at all times. Keep going until there is no pressure on the top mount, at which point until the main piston nut and remove the top mount. Pay attention to the order things go on, as there s a metal washer between the top mount and the spring top cap. Now gradually loosen the spring clamps, again in equal amounts on alternating clamps.
4 You can also put some grease into the top mount bearings at this point and generally check they are not too rough running. Also check the bump stop (brown foamy looking bit) condition and overall condition of the strut. If you can easily compress the shock absorber by hand, it s on it s way out. Mine were solid thankfully! New spring (left) vs old spring (right): Fitting the new spring is, obviously, the reverse of the removal procedure. Springs are fitted with the writing the right way up. Place the spring top cap on the spring, put the clamps on and compress. Locate the spring on the rubber seat. THE END OF THE SPRING DOES NOT NEED TO SIT UP AGAINST THE GROOVE IN THE RUBBER SEAT, in fact, it probably sits about 30mm away from it. Ensure the spring is located around the seat properly and isn t resting on the inner lip of it. Check the top mount can be fitted if not, compress the springs further. Place the metal washed on the spring top cap, then reinstall the top mount and tighten the main piston nut. Gradually release the spring clamps as before. You can now remove the locating lugs (see A on first page picture) as this will allow more camber adjustment in future. Simply knock them off using a large screwdriver and a hammer. Reinstall the strut onto the car. Hold it up in place and put on the 3 nuts on the top mount on finger tight for now. Relocate the strut in the lower clamp. You can see where the clamp was before quite easily as it s the clean bit! You may need to support the hub whilst you do up the main clamp bolt, to make sure the strut is fully home whilst you clamp it.
5 Reinsert the drop link into its hole and tighten the nut. Again, you ll need to prise down the anti-roll bar to locate it. That s it for the fronts. Not so bad, huh? Now for the real easy bit. Rear Springs Jack up the car as before and remove the wheel. Undo the bolt on the lower end of the rear suspension strut. You ll need your breaker bar to just crack it loose, then you can use the ratchet. Careful, as when its out the rear trailing arm and shock absorber will move, so what your arms/fingers are not under either of these. Now the technical bit.. Stand on the rear hub and remove the spring, complete with rubber seat (that sits on the trailing arm)!
6 Remove the rubber seat from the spring. Rear springs old (left) vs new (right) Fit the rubber seat into the new spring (again, writing the right way up). The rear spring locates on lugs on the chassis at the top (left pic below) and on the trailing arm at the bottom (right pic below) To bolt the rear shock back in place, you will need to place an axle stand under the brake disc hub and gently lower the car until the shock bolt lines up with the hole on the hub and you can bolt it up. That is it. The springs will take a couple of weeks / few hundred miles to settle. You will also need to have a 4 wheel alignment done to ensure everything is running straight, or else you will have weird tyre wearing and/or handling. You can either have this done straight away (as the settling of the springs won t really throw things out much) or wait a few weeks then have it done. Hope this has been of use. Big thanks once again to Kav (aka Westside) for his help. Russ **Just because you have to say this: Please remember this is only what I did and these notes (albeit described in great detail) are for guidance only. As with anything car related, if you are unsure, please get advice or help from a professional mechanic. I / e36coupe.com / BMWowner.com cannot and will not be held responsible if you damage yourself or something on your car. Thanks**
GTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com
GTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com This procedure covers replacing the front wheel bearings. Tools and Parts required: Wheel Bearing Puller w/ ABS adapter. Available for rent from
More informationTooling List 17mm Socket 17mm Wrench 24mm Wrench 26mm Wrench 3/8 Drive Ratchet Torque Wrench
Thank you for purchasing the CorkSport Rear Adjustable Camber Arms. By replacing your OEM camber arms with the CorkSport Adjustable Camber Arms, you will be able to dial in your suspension with +/- 5 degrees
More informationVW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS
VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS Tools required: 10mm/13mm socket and 3/8 drive ratchet with extension Torx T20/25/30 screwdrivers or bits Phillips head screwdriver,
More informationTool And Material Checklist
HOW - TO CV JOINTS CV JOINTS Tool And Material Checklist Screwdriver Metal Shears Breaker Bar or Torque Wrench Assorted Wrenches Wire Evaporating Spray Solvent Pusher Tool Vise Snap Ring or Duckbill Pliers
More informationINSTALLATION INSTRUCTIONS COMPETITION SERIES COILOVER SUSPENSION SYSTEM 03+ Scion xb
INSTALLATION INSTRUCTIONS COMPETITION SERIES COILOVER SUSPENSION SYSTEM 03+ Scion xb NOTE: Progress Technology products should only be installed by a qualified licensed mechanic experienced in the installation
More informationSUSP-06, Torsion Bars - Removing, Replacing, and Indexing
Introduction SUSP-06, Torsion Bars - Removing, Replacing, and Indexing Replacing the torsion bar on a 944 is not all that difficult. However, reindexing the torsion after completion is a pain and can be
More informationFront axle components, overview
just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,
More information1993 SUSPENSION Volkswagen Front. EuroVan
Article Text ARTICLE BEGINNING 1993 SUSPENSION Volkswagen Front EuroVan DESCRIPTION FWD independent suspension is an double-wishbone type with torsion bars mounted on upper control arm. Wheel is supported
More informationAIR-SUSPENSION. Art. nr.: L.L200.07.C.M. Auxiliary Air Suspension. Designed for: Mitsubishi L200. From: 2007& UP RDW 71/320-0569
AIR-SUSPENSION Dunlop Systems and Components Het Wegdam 22 7496 CA Hengevelde The Netherlands Tel.: +31-547-333065 Fax: +31-547-333068 Website: www.dunlopsystems.com Art. nr.: L.L200.07.C.M Designed for:
More informationSCION tc 2005-2008 COIL OVER SUSPENSION Preparation
SCION tc 2005-2008 COIL OVER SUSPENSION Preparation Part Number: PTR11-21070 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item # Quantity Reqd. Description
More information2011-14 F250 6 RADIUS ARM KIT
92154000 Thank you for choosing Rough Country for your suspension needs. 2011-14 F250 6 RADIUS ARM KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,
More information2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13)
2008 ACCORD - Front Knuckle/Hub/Wheel Bearing Replacement (page 18-13) Exploded View Special Tools Required Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool 07GAF-SD40100 Bearing driver attachment,
More informationCorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6
CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 Pre-Installation Notes: The CorkSport Rear Sway Bar is a great addition to improving the handling performance to the Mazdaspeed 6. It will minimize
More informationVerify caster, camber and toe-in are correct before proceeding.
If rotating the tie rod end 360 degrees changes the toe-in too much, use the rack tie rod to make smaller adjustments. Put the tie rod end in the steering arm and snug the castle nut before adjusting.
More informationTUTORIAL. REbUILdING. front CALIpER O-RING CONVERSION CORVETTE 1965-82. Part #: HT-1
Part #: HT-1 1965-82 CORVETTE O-RING CONVERSION front CALIpER REbUILdING TUTORIAL Choosing a Brake Caliper Rebuild Kit Standard Lip Seals vs. O-Ring Seals Lip seal design seals are used on 1965-1982 Corvette
More informationINSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES
INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationReplacing the handbrake drum/rear output shaft oil seal. Series models.
Replacing the handbrake drum/rear output shaft oil seal. Series models. You may notice oil coming out of your handbrake (transmission brake) drum. This will in all probability be a leak from the gearbox
More information2005-2007 Ford Focus Front Brake Rotors
2005-2007 Ford Focus Front Brake Rotors Replacement Replacing the rotors in 2005-2007 Ford Focus models with rear drum brakes. Written By: David Hodson INTRODUCTION The steps in this guide are used to
More informationINSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113)
INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE
More informationFord Super Duty Rear Brake Pad & Rotor Replacement. 2004 F250 4x4 XLT Sport Crew Cab
Page 1 of 31 Ford Super Duty Rear Brake Pad & Rotor Replacement 2004 F250 4x4 XLT Sport Crew Cab Back to 2004 F250 Main Page Click Here for a PDF version of this article *** NOTE *** Some of you may remember
More informationStreet-Lynx. Reilly MotorSports, Inc. Installation Manual
Street-Lynx By Reilly MotorSports, Inc. Installation Manual 1 1- Begin by removing your original rear suspension disconnect your brake lines, E-brake cables, and remove the driveshaft. To prevent fire
More informationFord F-Series Column Shift Repairs
Ford F-Series Column Shift Repairs I ve had it on my list to tighten up the linkage on my 52 s column shift setup for a long time. I tried to get it apart when I had all the front end sheet metal off,
More informationDrive shaft, servicing
Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,
More informationVW Caddy W21-760-3503 INSTALLATION INSTRUCTIONS
Unit 626 Kilshane Avenue, North West Business Park, Ballycoolin, Dublin 15, Ireland Telephone: +353 1 8612 632, Fax: +353 1 8612 647, email: sales@driveriteltd.com www.driveriteltd.com VW Caddy W21-760-3503
More informationAXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION
AXLE SHAFTS - FRONT 1998 Pontiac Bonneville 1998-99 DRIVE AXLES FWD Axle Shafts - Cars - "C", "G" & "H" Bodies GM Aurora, Bonneville, Eighty Eight, LeSabre, LSS, Park Avenue, Regency, Riviera MODEL IDENTIFICATION
More informationHow to remove, replace and tighten accessory belts for a second generation (NB, 1999-2005 ) Mazda Miata MX-5
How to remove, replace and tighten accessory belts for a second generation (NB, 1999-2005 ) Mazda Miata MX-5 If your Miata is squealing loudly either when you engage the air conditioner, turn on the car,
More informationDO NOT attempt to repair hub and wheel bearing assembly.
Page 1 of 6 HUB & WHEEL BEARINGS (WITH PULSE VACUUM HUBLOCK) DO NOT attempt to repair hub and wheel bearing assembly. Removal DO NOT remove hub lock assembly by prying on hub lock legs. This can crack
More informationTUTORIAL. REbUILdING. REAR CALIpER O-RING CONVERSION CORVETTE 1965-82. Part #: HT-2
Part #: HT-2 1965-82 CORVETTE O-RING CONVERSION REAR CALIpER REbUILdING TUTORIAL Choosing a Brake Caliper Rebuild Kit Standard Lip Seals vs. O-Ring Seals Lip seal design seals are used on 1965-1982 Corvette
More informationYour New Frog Bike. Congratulations on purchasing a new bike and thank you for choosing Frog!
Your New Frog Bike Congratulations on purchasing a new bike and thank you for choosing Frog! We know that you must be raring to go but before you do there s a few little things still to do to get you up
More informationHow To: Replace aux belt & pulley on a HDi
How To: Replace aux belt & pulley on a HDi Thought I would share my recent experiences with the coupe and give you a little how to on replacing the auxiliary drive belt and crankshaft pulley on the Hdi.
More informationSTEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER
14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------
More information16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1
16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1 BD Adjustable Track Bar w/bracket Dodge 2500-3500 4WD Models 1994-2002 Dodge 1500 4WD Model 1994-2001 P/N# 1032011-F
More informationLIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions
LIFT-505 BMF Lift Kit Yamaha Drive Gas or Electric Installation Instructions Contents of LIFT-505 Yamaha Drive BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger
More informationReadyLift (Part# 66-5075) Strut Extension, Installation Instructions Toyota Tundra New Body Style 2WD & 4WD
SAFETY WARNING: recommends this system be installed by a professional technician. In addition to these instructions, professional knowledge of disassembly/ reassembly procedures and post installation checks
More informationBUGGY SETUP GUIDE. Volume GOKARTSUSA GY6 150, CN250. Buggy Setup Guide
BUGGY SETUP GUIDE Volume 1 GOKARTSUSA GY6 150, CN250 Buggy Setup Guide GY6 150, CN250 DUNE BUGGY Buggy Setup Guide GOKARTSUSA.COM 2000 Highway 50 S. Lake Tahoe, CA 96150 Phone 800.603.1437 2 Table of Contents
More informationRear wheel brakes, servicing. Стр. 1 из 45. Note:
Volkswagen Touareg - Rear wheel brakes, servicing Стр. 1 из 45 46-2 Rear wheel brakes, servicing Rear brakes, FN 44 brake caliper, servicing Note: After replacing brake pads, depress brake pedal firmly
More informationFront brakes (FN- 3), servicing
j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly
More informationSLACK PERFORMANCE KARTS
SLACK PERFORMANCE KARTS SET UP GUIDE Thank you for purchasing a 2013 Slack Axiom Chassis. Performance Mfg. strives to provide you with the very best chassis and components on the market today. Your satisfaction
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure
More informationLittle British Car Co.
Little British Car Co. 29311 Aranel, Farmington Hills, MI 48334-2815, USA Tel: 248 489 0022 or 800 637 9640 Fax: 248 489 9665 On the web at: www.lbcarco.com E-mail: LBCarco@LBCarCo.com MGB Tube Rear Shock
More informationAXLE SHAFTS - FRONT. 1993 Toyota Celica DESCRIPTION REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION. 1993 DRIVE AXLES Toyota FWD Axle Shafts
AXLE SHAFTS - FRONT 1993 Toyota Celica 1993 DRIVE AXLES Toyota FWD Axle Shafts Toyota; Celica DESCRIPTION Axle shafts transfer power from transaxle to driving wheels. All axle shafts consist of a shaft
More informationUnit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008)
Rear Wheel/Brake/Suspension 13. Rear Wheel/Brake/Suspension Service Information 13-1 Troubleshooting 13-2 Rear Wheel 13-3 Rear Cushion 13-4 Rear Swing Arm 13-7 Service Information General Safety If the
More information1.8 CRANKSHAFT OIL SEALS
SERIES 60 SERVICE MANUAL 1.8 CRANKSHAFT OIL SEALS An oil seal is fitted between each end of the crankshaft and the bores of the flywheel housing and gear case cover to retain the lubricating oil in the
More informationAWE Tuning Air/Air Intercooler Kit for 2000-04 Audi 2.7T
AWE Tuning Air/Air Intercooler Kit for 2000-04 Audi 2.7T Congratulations on your purchase of the AWE Tuning Intercoolers for your 2.7T Audi. Hundreds of hours of design and operational testing were spent
More informationRange Road RR Series Semi-Automatic Firewood Processor. Crated Unit Assembly Manual
Range Road RR Series Semi-Automatic Firewood Processor Crated Unit Assembly Manual 1 1) Undo 8-18mm x 19mm Nuts and bolts, 2 on each leg of top frame 2) Lift top of Metal crate off and move out of work
More informationFRONT SUSPENSION Click on the applicable bookmark to selected the required model year
FRONT SUSPENSION 33A-2 FRONT SUSPENSION General Information GENERAL INFORMATION 33200010105 The front suspension on 2WD vehicles is an independent suspension system having the double wishbone combined
More informationTRANS-05, Torque Tube Removal, Rebuilding, and Installation
TRANS-05, Torque Tube Removal, Rebuilding, and Installation Tools Metric Wrench Set Metric Socket Set Jack Stands (6 minimum) Floor Jack 8mm Cheesehead socket (also referred to as 12 point internal socket
More informationassembly instructions
assembly instructions 1 // this guide is for Urban Chic gents & ladies. // this guide is for Urban Chic gents & ladies. 2 1 x ph screwdriver 2 x 10mm spanners 1 x 15mm spanners 1 x 13mm spanners 1 x 6mm
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)
46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel
More informationINSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5
CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to
More informationChar-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997
Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47
More informationInstallation instruction do88 Intercooler for Volvo S40 / V50 / C30
Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 This instruction shows how to replace the OEM intercooler with our performance intercooler. 2. 3. 1. 4. 5. Part number: ICM-170 6. At
More informationInstallation manual. 3 suspension system. 2009-2013 Ford F150. Part # 23000. Part # 23000. Important customer information: 2009-2013 Ford F150
Installation manual 3 suspension system 2009-2013 Ford F150 Part # 23000 sj12112012rev.03 Part # 23000 2009-2013 Ford F150 3 suspension system Part # Description Qty. 23000-01 Driver side upper control
More informationMM Adjustable Tie-Rod Ends (MMTR-2, -4, -7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Adjustable Tie-Rod Ends (MMTR-2, -4, -7) PLEASE NOTE: The use of 1996-2004
More informationMKIII 2.0 Golf/Jetta Rear Disk Brake DIY
MKIII 2.0 Golf/Jetta Rear Disk Brake DIY This "how to" assumes you have some basic tools, and safety gear. Safety glasses should be worn at all times when working with tools and automotive fluids. Always
More informationRebuild Instructions for 70001 and 70010 Transmission
Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before
More informationWHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES
WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES For 1234 1992 WHEEL ALIGNMENT Subaru Specifications & Procedures Justy, Legacy, Loyale, SVX * PLEASE READ THIS FIRST * NOTE: Prior to performing wheel alignment,
More informationGo-kart for little race-drivers
Go-kart for little race-drivers Drill and drive. Go-kart What it lacks in speed, it more than makes up for in fun: the go-kart will excite little race-drivers. 1 Introduction It s only a go-kart, but it
More informationDANA 30 MANUAL HUB CONVERSION KIT
DANA 30 MANUAL HUB CONVERSION KIT 12194 PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE YOU BEGIN Your safety and the safety of other motorists is very important. Your Jeep is an off road capable vehicle
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More informationRollator Cane and Brake Replacement SAFETY SUMMARY (CONTINUED)
Rollator Cane and Replacement Assembly, Installation and Operating Instructions SAVE THESE INSTRUCTIONS NOTE: Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use. Contact Carrier/Dealer
More informationCompetition 4 & 6 suspension Lift Toyota Landcruiser & nissan patrol
Competition 4 & 6 suspension Lift Toyota Landcruiser & nissan patrol Competition suspension Product Guidelines Guidelines for sale and recommendation of 4 (100mm) and 6 (150mm) Lifts for Toyota Landcruiser
More informationMKV Golf GTI Rear Brake Service - Replace Pads and Rotors
Page 1 Installation Procedures MKV Golf GTI Rear Brake Service - This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of
More informationREAR AXLE 27-1 CONTENTS 27109000161 ON-VEHICLE SERVICE... 3 GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 2 SPECIAL TOOLS... 2 REAR AXLE HUB...
27-1 REAR AXLE CONTENTS 27109000161 GENERAL INFORMATION... 2 SERVICE SPECIFICATIONS... 2 SPECIAL TOOLS... 2 ON-VEHICLE SERVICE... 3 Wheel Bearing Axial Play Check... 3 Wheel Bearing Rotary-Sliding Resistance
More information»Product» Safety Warning
C1200 Installation Instructions 2007-2016 Chevy/GM 1500 2/4wd 2" Strut Spacer Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More informationSolstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
More informationCOOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011
COOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011 Below are instructions for the Mini Mania Pulley Upgrade Kit, Part Number NME5011. Please take all necessary precautions for working
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More informationTitle: Best Practices Removal and Installation of Wheel Assembly (Tire Mounted to Rim Assembly) From Container Chassis
INSTITUTE OF INTERNATIONAL CONTAINER LESSORS IICL Chassis Technical Bulletin CTB 021, February 12, 2015 Title: Best Practices Removal and Installation of Wheel Assembly (Tire Mounted to Rim Assembly) From
More informationTABLE OF CONTENTS. Section 1 - Assembling your new pit bike.
Orion Pit Bike Sales Owners Manual (All information and content is the property of Orion Pit Bike Sales. Any attempt to copy or resell is a direct violation of our copyright. All violators will be prosecuted)
More informationWhite Industries Rear Hub Instructions
White Industries Rear Hub Instructions Tool required: 2mm allen/hex wrench, 19mm socket, 20mm socket, and mallet. 1. Loosen the set screws located in the adjusting collar by using a 2mm allen wrench inserted
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)
47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing
More informationInstalling Ball joints on a Ford 1999-2004 Superduty Pickup truck REV2 7-8-07
Installing Ball joints on a Ford 1999-2004 Superduty Pickup truck REV2 7-8-07 Pre-introduction My name is Kenny Gallo, I am not a certified mechanic in any way shape or form. I work on my truck as a hobby.
More information6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included:
Revised May 205 6-08/6-09 6 inch A-Arm Lift Kit will fit CLUB CAR DS installation instructions included: Rear Lift Blocks Main Suspension Assembly Spindles A-Arms Rear Shock Mounting Plates U-Bolts WARNING:
More informationRULE # 1 is DON T mess with things that you don t know anything about! (Take them to a pro & pay them to fix it)
OK there seems to be a LOT of problems noted on KatRiders having to do with CARBS, so I thought I d write out sort of a checklist of things to help folks. RULE # 1 is DON T mess with things that you don
More informationC5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions
C5 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions Ok, let's start with taking the radio bezel dash area off first. Here is what the OEM radio looks like... First you flip
More informationInstallation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5
INSTALLATION GUIDE Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 Take every precaution to make this installation a safe procedure. Make safety the number
More informationhttp://localhost/vida/jsp/information/xml/xmldocprintpreview.jsp
Page 1 of 7 60: Wheel alignment V70 XC (01-) / XC70 (-07), 2001, B5244T3, AW50/51 AWD, L.H.D, YV1SZ58D811036138, 036138 5/4/2014 PRINT 60: Wheel alignment Wheel alignment, checking / adjusting Note! For
More informationWHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES
WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES 1998 Mitsubishi Montero 1997-98 WHEEL ALIGNMENT Mitsubishi - Specifications & Procedures Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport, 3000GT RIDING
More informationTri-Homo Style Operation and Maintenance Instructions
Tri-Homo Style Operation and Maintenance Instructions One Research Drive Stratford, CT 06615 (203) 375-0063 www.sonicmixing.com 1 Installation and Start-up Do not perform following adjustments without
More informationOwner s Manual Read and keep this manual. Patents World Wide
Owner s Manual Read and keep this manual. Patents World Wide S & S Industries, Inc., Sarasota, FL, USA www.trail-gator.com Copyright 2008 All Rights Reserved The following manual is provided to assist
More informationBODY-12, Door Handle - Removal, Installation, and Adjustment
Introduction BODY-12, Door Handle - Removal, Installation, and Adjustment There are many different procedures floating around describing how to replace the door handles on a 944 and every one of them will
More information(A4) Suspension and Steering Sample Questions and Answers
(A4) Suspension and Steering Sample Questions and Answers Answers to these questions are found beginning on page 4 of this document 1. Two technicians are discussing the replacement of an inner tie rod
More information12. REAR WHEEL/BRAKE/SUSPENSION
12 12 12-0 SERVICE INFORMATION... 12-1 REAR BRAKE... 12-5 TROUBLESHOOTING... 12-2 REAR SHOCK ABSORBER... 12-8 REAR WHEEL... 12-3 REAR FORK... 12-9 SERVICE INFORMATION GENERAL INSTRUCTIONS When installing
More informationInstallation manual. 1.75 front leveling kit. 2011 Dodge Durango 2011-2014 Jeep Grand Cherokee. Part # 42006. Part # 42006
Installation manual 1.75 front leveling kit 2011 Dodge Durango 2011-2014 Jeep Grand Cherokee Part # 42006 sj02282011rev.01 Part # 42006 2011-2014 Dodge Durango 2011 Jeep Grand Cherokee 1.75 front leveling
More informationFRONT WINDSHIELD SEAL INSTALLATION
FRONT WINDSHIELD SEAL INSTALLATION Tech Article From Newsletter 16.1-1st Quarter of 2010 Replacing your Front Windshield Seal ISN T AS HARD AS YOU MAY THINK! Recently, we retooled our front window seal
More informationTECHNICAL BULLETIN. Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves. How the Cab Leveling and Chassis Leveling Valves Work
Revised 02-00 TECHNICAL BULLETIN Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves This technical bulletin covers both cab and chassis leveling valves manufactured by Meritor WABCO. While the
More informationARVINMERITOR UNITIZED FRONT WHEEL HUB INSPECTION AND MAINTENANCE
SERVICE BULLETIN (Also applies to Mack Trucks Australia) NUMBER: SB-423-002 DATE: 8/23/02 MODEL: All with FF981 Front Axle ARVINMERITOR UNITIZED FRONT WHEEL HUB INSPECTION AND MAINTENANCE The ArvinMeritor
More informationELECTRIC BICYCLE USER MANUAL
ELECTRIC BICYCLE USER MANUAL 1 Main Technical Parameters and Specification Weight: 23 kg Wheel size: 20 Maximum speed: 25 km/h E BIKE URBAN Range: Up to 45km (with pedal assist) Type: lithium Voltage:
More informationhttp://uk-mkivs.net/forums/t/175611.aspx
Page 1 of 6 uk-mkivs» Technical Community» D.I.Y Guides and How to Instructions.» Outer CV Gaiter replacement How to...56k make a cupa [;)] Outer CV Gaiter replacement How to...56k make a cupa [;)] Search
More information92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540
92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540 www.airliftperformance.com MN-514 (06409) NPR 4762 Please read these instructions completely before proceeding with installation
More informationAwning Instructions. Standard Manual 1.5m to 4.5m
Awning Instructions Standard Manual 1.5m to 4.5m English Standard Manual Instructions Contents Warning 1.5m 3.0m Awnings 4 x Expansion bolts (2 per bracket)** 2 x brackets 1 x Awning 1 x Winder handle
More informationTiming Belt Change 200 TDI Land Rover Supplied by: Jason Crawford www.landroverweb.com
Timing Belt Change 200 TDI Land Rover Supplied by: Jason Crawford If there was ever a job that was made out to be more than it should be, then this is it. Changing a timing belt on a Defender is pretty
More informationWHEEL ALIGNMENT 4WD SA 6
SA6 WHEEL ALIGNMENT 4WD 1. MAKE FOLLOWING CHECKS AND CORRECT ANY PROBLEMS (a) Check the tires for wear and proper inflation. Cold tire inflation pressure: See page A25 (b) Check the wheel runout. Lateral
More informationWheel Stud Conversion Kit Installation Instructions
Wheel Stud Conversion Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing
More informationINSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05
INSTRUCTIONS -J04 REV. 0-9-04 General FLHR/C/S (Road King) FRONT END LOWERING KIT This kit is designed for installation on 00 and later FLHR/C/S Model Motorcycles. Road King models use the conventional
More information8) Push piston in the remaining distance while bleeding through bleed nipple
1 of 16 Replacing Brake pads on a Jeep Cherokee (XJ) Copyright 2004 jeep@blackonyx.net *All things shown or advice given in this PDF is to give you ideas of what can be done. They may not be suited to
More information...and for choosing Rocker BMX, you have chosen wisely. We appreciate the market is slightly clouded with various brands of so called mini bmx.
...and for choosing Rocker BMX, you have chosen wisely. We appreciate the market is slightly clouded with various brands of so called mini bmx. However, Rocker is very different from other brands; it was
More informationASSEMBLY MANUAL SE-4S35
Automatic drive ASSEBLY ANUAL SE-4S35 AI-4S35 SG-4R35 Battery box otor unit Inter-4 hub CONTENTS WARNING 1 INSTALLATION CONITIONS Battery box Speed sensor Cable lengths and diameters otor unit Recommended
More informationO SL. BPW Original spare parts Air suspensions series O / SL / AL BPW BERGISCHE ACHSEN BPW ORIGINAL SPARE PARTS. BPW Original spare parts
BPW riginal spare parts Air suspensions // BPW BERGISCHE ACHSEN BPW riginal spare parts Air suspensions series / / BPW RIGIN SPARE PARTS BPW riginal spare parts Air suspensions Contents Page Air suspension
More information