19410 STREET COIL SET 01-UP LEXUS IS300 INSTALLATION OF FRONT COIL SPRINGS

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "19410 STREET COIL SET 01-UP LEXUS IS300 INSTALLATION OF FRONT COIL SPRINGS"

Transcription

1 19410 STREET COIL SET 01-UP LEXUS IS300 Thank you for your purchase from our line of Lexus parts. Please call us at (877) 4NO-ROLL if you have any questions regarding the service or installation of your Hotchkis products. Visit us This installation will require: A coil spring compressor, jack stands, floor jack The following wrenches or sockets: 10mm, 12mm, 14mm, 17mm The following Allen wrenches or hex sockets: 5mm Torque wrench. INSTALLATION OF FRONT COIL SPRINGS 1) Securely block the rear wheels of the vehicle. Do not jack up the vehicle yet! 2) Use a 10mm socket or wrench to loosen and remove the two small nuts holding the electrical box to the strut mounts on the driver s side. Remove the two nuts on the passenger side as well to remove the heat sync. THIS ITEM MAY BE HOT! Move both components off to the side and retain the stock mounting hardware. This should expose the strut mount nuts on each side.

2 3) Use a 12mm socket or wrench to loosen and remove the nuts securing the top of the strut. Retain the nuts for later re-installation. 4) Use a jack to slowly raise the front of the car and support on jack stands. The struts will slowly drop free of the holes in the body, but will not fall out. Remove the front wheels. From this step on it is best to work on each strut separately. 5) Use a 10mm wrench or socket to loosen and remove the small bolt holding the brake line to the strut assembly. Use a 10mm wrench to disconnect the ride height sensor from the body on the driver s side of the vehicle. Retain all hardware for later re-installation. 6) Use a 14mm wrench and a 5mm Allen wrench to loosen and remove the nut holding the top part of the end link to the sway bar. Retain the hardware for later re-installation.

3 7) Use a 17mm socket or wrench to loosen and remove the bolt holding the lower end of the strut to the spindle. Retain this hardware for later use. 8) Use a 12mm wrench or socket to remove the small bolt holding the top of bracket mounted to the spindle in place. This bolt is just behind the lower end of the strut. Retain the hardware. 9) Use a 17mm socket to remove the bolt holding the lower end of the sway bar end link to the spindle. This bolt passes through the bracket the bottom of the strut mounts to. You may have to use a wobble extension to get a socket past the steering tie rod. The strut assembly and mounting bracket should now be free for removal. Retain the stock hardware.

4 10) Secure the strut assembly in a coil spring compressor (these can be rented from most major auto parts stores). Remove the top plate from the strut and retain it for later re-installation. Use a paint marker or similar tool to mark the top plate and coil for alignment purposes. 11) Use a flat blade screwdriver or similar tool to remove the plastic dust cover concealing the top nut on the strut. Compress the coil to take tension off the top plate and use a 17mm socket to remove the nut. Retain the nut for later re-installation. 12) Remove the upper strut plate with the dust cover boot. Remove the stock bump stop from the strut or the dust cover if it s lodged inside. Release the tension on the coil and remove the stock coil. Retain the top plate and dust cover. You may discard the stock bump stop.

5 13) Slide the new Hotchkis bump stop over the top of the strut with the narrow end towards the bottom of the strut. Place the Hotchkis spring over the strut shaft and locate the tail of the coil in the stamped recess on the spring seat. Place the top strut plate and dust boot over the spring. 14) Collapse the coil so that you can start the nut on the end of the shaft to hold the strut top plate in place. Use a 17mm wrench to tighten the nut. Make certain to align the strut top plate and lower spring seat using the white marks you made earlier. Torque the hardware to 35 ft/lbs. Replace the dust cap over the hole in the top of the strut. Release the tension on the spring slowly, and make certain the spring lines up with the spring seat properly. 15) Remove the strut assembly from the coil compressor and lift it back into the vehicle. Slide the lower strut mount bracket over the spindle with the bottom end of the strut inside the bracket. Secure the bracket with the stock screw at the top behind the strut mount using a 12mm wrench to tighten the bolt. Torque the screw to 25 ft/lbs.

6 16) Re-install the end link. Slide the stud on the end link through the bracket and spindle. Use a 17mm wrench to tighten the stock nut onto the stud. Slide the lower strut bolt through the bracket and the bottom of the strut. Use a 17mm socket or wrench to tighten the nut and bolt. Torque both nuts to 30 ft/lbs. 17) Re-attach the end link to the sway bar. Use a 5mm Allen wrench and a 14mm wrench to tighten the end link. Tighten the end link hardware to 25 ft/lbs. 18) Use a 10mm wrench or socket to re-attach the brake line to the strut using the stock screw. Torque the hardware to 15 ft/lbs. Use a 10mm wrench to re-attach the ride height sensor on the driver s side if you re installing that side. Torque the hardware to 15 ft/lbs.

7 19) Push the top of the strut up to the hole in the body. Slide the studs through the holes and secure them by starting the nuts onto the studs. Do not tighten the nuts at this time! 20) Repeat steps 5-18 for the opposite site strut and recheck all hardware for tightness. 21) Replace the front wheels, and use a jack to slowly lower the vehicle to the ground. Pay attention to the strut tops to make certain the studs are lined up with the holes in the body. With the full vehicle weight on the struts, you may tighten up the top nuts. Use a 12mm socket or wrench to tighten the nuts. Torque the hardware to 35 ft/lbs. 22) Use a 10mm socket or wrench to re-attach the electrical components from step 2 to the studs that you removed them from. Torque the hardware to 25 ft/lbs. 23) Re-check all hardware for tightness. With the front installation complete you can now move on to the rear spring installation!

8 This installation will require: A coil spring compressor, jack stands, floor jack. The following wrenches or sockets: 10mm, 12mm, 14mm, 17mm, 19MM The following alan wrenches or hex sockets: 6mm Torque wrench. INSTALLATION OF REAR COIL SPRINGS 1) Securely block the front wheels of the vehicle. Remove the trunk interior to gain access to the upper shock mounts in the rear. Lift out the carpet and spare tire cover components. Use a 10mm socket or wrench to remove the four tie-down loops in the trunk. Remove the trim clips indicated by the arrows. There should be four on each side with two along the rear panel and two mounted just behind the fender well. Unscrew and remove the two plastic tie down mounts located at the lip of the trunk. The interior panels should now be loose for removal.

9 2) Use a 14mm socket or wrench to loosen and remove the nuts holding the tops of the struts in place. Retain the hardware for later re-installation. 3) Use a jack to raise the rear end until the wheels are off the ground and use jack stands to support the vehicle. Remove the rear wheels. From this step on it s best to work on each strut separately. 4) Use a 12mm socket or wrench to loosen and remove the bolt holding the top of the strut inside the rear fender well. Retain the hardware for later re-installation. 5) Use a 12mm socket or wrench to loosen and remove the long bolt and nut holding the rear sway bar end link to the rear suspension arm.

10 6) Use a 19mm socket or wrench to loosen and remove the bolt holding the lower end of the strut to the suspension arm. Use the 19mm wrench to then remove the bolt holding the lower suspension arm to rear sub frame. Use caution as the strut is not held in by anything at this stage, and may drop out as the arm is disconnected! 7) Place the stock strut assembly into a coil spring compressor. Use a paint marker or similar marking tool to make a set of alignment marks on the upper and lower spring seats. 8) Compress the coil and use a 17mm wrench and a 6mm Allen wrench to loosen and remove the strut retainer nut. Release the coil and lift off the top strut plate hat and stock spring.

11 9) Remove the stock bump stop. The stop may be on the strut shaft, or lodged inside the upper strut plate hat. If it s stuck inside the hat just shake it a bit to dislodge it. Retain the metal hat from the stock bump stop and slide the Hotchkis stop into the plate. Slide the complete bump stop assembly over the end of the shaft with the narrow end of the stop pointed towards the bottom. 10) Drop the new Hotchkis spring over the end of the strut. Line up the end of the coil with the stamping in the lower spring seat. Slide the upper spring seat hat over the end of the strut. 11) Compress the spring and slide the large cupped washer over the top of the strut with the cupped edge turned upwards. Align the spring seats using the marks you made earlier. Use a 17mm wrench and a 6mm Allen wrench to tighten the top nut. Torque the hardware to 35 ft/lbs.

12 12) Slowly release the spring compressor. Make certain the coil seats properly to the upper spring seat / strut top plate. Remove the strut assembly from the compressor for re-installation. 13) Slide the base of the strut assembly into the lower suspension arm and lift the arm back up to the sub frame. Reconnect the arm using the stock hardware and a 19mm socket or wrench. Torque the hardware to 80 ft/lbs. 14) With the suspension arm re-attached, you can now slide the stock hardware though the arm and lower strut end. Use a 19mm wrench or socket to torque the bolt to 60 ft/lbs. Re-attach the end link bolt through the arm. Use a 12mm socket or wrench to torque the hardware to 30 ft/lbs. 15) Re-attach the small bolts holding the strut to the inside of the fender well. Use a 12mm socket or wrench to tighten the bolts. Torque the hardware to 30 ft/lbs.

13 16) The studs on the top strut plate should be sticking though the holes in the trunk. Start the nuts onto the studs, but do not tighten them yet. 17) Repeat the removal and installation process, steps 4-16, for the opposite strut. With both struts rebuilt and in place you can re-install the wheels. Use a jack to slowly lower the vehicle, and watch the strut tops to make sure they slide through the holes in the body. With the full vehicle weight on the struts you may use a 14mm socket or wrench to torque the nuts to 35 ft/lbs. 18) Re-check all hardware for tightness. Finish the install by putting the trunk interior back into place. Congratulations, you re now finished installing your set of Hotchkis coil springs! Lexus IS300 Street Coil set, Parts List P/N Hotchkis P/N Item Description Quantity per kit Front Coil Spring Rear Coil Spring Front Bump Stop Rear Bump Stop 2 Items Not Pictured at Right 5 n/a Instruction Set 1 Visit Hotchkis on the web at or Call (562) to order more Hotchkis products for your Lexus IS300!

14 Hotchkis Performance LLC Return Policy & Limited Warranty Effective January 1, 2009 all Hotchkis products must be registered to qualify for warranty at or via the mail-in warranty card, included with the product, within 30 days of the original purchase date. Return Policy We want you to be completely satisfied with your Hotchkis Performance product. For products, presenting signs of shipping damage please contact the freight carrier immediately. All our products are guaranteed to be free from manufacturer s defects. If your order arrives with a manufacture defect, please contact our Customer Service Department at (562) You will be assigned a Returned Goods Authorization Number (RGA). The package you return must show the RGA on the outside of the package, include the original invoice and be shipped prepaid to our facility. The product has to be unused and in its original packaging materials. Exchanges or refunds made after 30 days will be subject to a 20% restocking charge. If you purchased your Hotchkis Performance product from an authorized dealer, you are still covered by this return policy. All returns however, should be made to your dealer, not to Hotchkis Performance directly. Limited Warranty Hotchkis Performance offers a Limited Warranty against defects in materials and workmanship of its products. This Warranty only applies to the original retail purchaser who retains ownership of the vehicle on which the product was originally installed. If the product is determined to be defective, Hotchkis Performance will repair, replace or refund the purchase price of the defective product at Hotchkis Performance's sole discretion, which shall fully satisfy and discharge any and all warranty claims. Any repaired or replaced product will be returned to the sender excluding the cost of freight. Products must be registered to qualify for warranty at or via the mail-in warranty card, included with the product, within 30 days of the original purchase date. Exclusions from Warranty Items offered but not manufactured by Hotchkis Performance are warranted according to the manufacturer's terms and are not covered by this limited warranty. Hotchkis Performance shall not be responsible for any labor, removal, installation, re-installation or maintenance costs. This warranty does not cover the cosmetic finish or plating of any product or any normal wear and tear to any product including, but not limited to bushings, brackets, end-links, hardware, steering components, shocks or springs. In addition, this warranty does not apply to any products that have been: Improperly installed or installed by someone other than a qualified, licensed auto mechanic experienced in the installation and removal of suspension products; Improperly serviced, misused, or modified, altered or subjected to abuse, negligence, accident or collision; Installed in any vehicle that has been modified; Installed on any vehicle that has carried loads in excess of automobile manufacturer suggested weight limits; or Installed on any vehicle that has been subject to abnormal or excessive use, including rallying, racing, or racing-type activities or off-road use. Limitation of Warranty This limited warranty is the entire and only warranty for the products and may not be modified or supplemented by any other person or company in any form. Any description of the products, by anyone, is for the sole purpose of identifying them and is not part of the basis of the bargain, and does not constitute a warranty that the products will conform to that description. The statements

15 of any salesperson do not constitute part of this limited warranty and cannot be relied upon as a warranty. THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. ANY IMPLIED WARRANTIES ARE DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW. THIS WARRANTY DOES NOT COVER CONSEQUENTIAL DAMAGES, LOSS OF TIME OR REVENUES, INCONVENIENCE, LOSS OF USE OF THE VEHICLE, DAMAGE TO THE VEHICLE OR COMPONENTS OF THE VEHICLE, ANY OTHER TYPE OF CONSEQUENTIAL DAMAGES, OR OTHER INCIDENTAL OR INDIRECT DAMAGES. HOTCHKIS MAXIMUM LIABILITY UNDER THIS WARRANTY SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages and in such states the above limitations or exclusions may not apply. This limited warranty gives the purchaser specific legal rights and the purchaser may have other rights that may vary from state to state. Technical Information Hotchkis Performance makes every effort to ensure that you are provided with the most accurate and up-to-date technical information. However, all technical information is approximate and may vary upon application. Additional suspension components may be needed in some applications, depending upon the make, model, engine and chassis of the vehicle. Hotchkis Performance is not responsible for any consequences resulting from manufacturer s technical mid-year changes. Hotchkis Performance products should only be installed by a qualified, licensed auto mechanic experienced in the installation of such products. Warranty Claim Procedure: The answer to ALL the following questions should be YES before making a warranty claim: Did you register the product at or via the mail-in warranty card within 30 days of purchase? Is the product appropriate to your application? Did you carefully and thoroughly read the instructions provided along with the product? Do you have the original invoice or sales receipt? Are you the original purchaser? Was the product properly installed by a qualified, licensed auto mechanic? Has the product been installed on the original vehicle on which it was installed at all times? Is the product unmodified and clean? Is the reason for return a legitimate product defect? If the answer to all these questions is YES, please contact our Customer Service Department at (562) You will be given a Returned Goods Authorization Number (RGA) valid for 60 days. You will also be asked to ship the product prepaid to our facility. All shipments MUST be (i) prepaid, (ii) include the original invoice or sales receipt, (iii) show the RGA on the outside of the package and (iv) include your name, address, make and model of the vehicle, and a brief description of the claimed defect, including the circumstances under which the defect occurred. If the warranty claim is deemed valid then Hotchkis will estimate shipping costs to return the repaired or replacement part and contact you for payment. Hotchkis s Limited warranty requires that any repaired or replaced product will be returned to the sender excluding the cost of freight. Warranty related inquires should be sent to the following address: HOTCHKIS PERFORMANCE, LLC C/O CUSTOMER SERVICE BURKE ST. SUITE 13 SANTA FE SPRINGS, CA 90670

16 Hotchkis Performance will not accept product returns without the RGA number, receipt and the information described above. C.O.D. or collect shipments will be refused. Once the returns are received at Hotchkis Performance, we will evaluate the products, verify the sales receipt, and investigate the warranty claim. Any repaired or replaced product will be returned to the sender. Effective January 1, This return policy and limited warranty supersedes all previous policy and warranty statements. Policies and warranties are subject to change without notice. Hotchkis Performance is not responsible for printing errors.

Sport Coil Springs Dodge Charger Hemi, Daytona R/T

Sport Coil Springs Dodge Charger Hemi, Daytona R/T Sport Coil Springs 19104 05 Dodge Charger Hemi, Daytona R/T Thank you for your purchase from our new line of Charger parts. Please call us at (877) 4NO-ROLL if you have any questions regarding the service

More information

Sport Coil Springs (19425) Scion tc

Sport Coil Springs (19425) Scion tc Sport Coil Springs (19425) Scion tc Thank you for your purchase from our new line of Scion tc parts. Please call us at (877) 4NO-ROLL if you have any questions regarding the service or installation of

More information

Installation manual. 1.75 front leveling kit. 2011 Dodge Durango 2011-2014 Jeep Grand Cherokee. Part # 42006. Part # 42006

Installation manual. 1.75 front leveling kit. 2011 Dodge Durango 2011-2014 Jeep Grand Cherokee. Part # 42006. Part # 42006 Installation manual 1.75 front leveling kit 2011 Dodge Durango 2011-2014 Jeep Grand Cherokee Part # 42006 sj02282011rev.01 Part # 42006 2011-2014 Dodge Durango 2011 Jeep Grand Cherokee 1.75 front leveling

More information

WARNING TO END USER, INSTALLER AND SELLER OF THIS PART!

WARNING TO END USER, INSTALLER AND SELLER OF THIS PART! WARNING TO END USER, INSTALLER AND SELLER OF THIS PART! By installing this part you are accepting full responsibility and liability for proper wheel and tire fitment after installation. It is the installer

More information

M7 Tuning Ultimate MINI Performance

M7 Tuning Ultimate MINI Performance M7 Coilover System Installation Guide M7 Tuning engineers and manufactures the highest quality MINI accessories and performance parts available anywhere on the planet! Please inspect your parts when you

More information

SCION xb LOWERING SPRINGS Preparation

SCION xb LOWERING SPRINGS Preparation Preparation Part Number: PTR07-52080 Kit Contents Item # Quantity Reqd. Description 1 2 Front Springs 2 2 Rear Springs 3 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description 1 2 3

More information

2015 & UP F-150 FRONT LEVELING KIT INSTALLATION

2015 & UP F-150 FRONT LEVELING KIT INSTALLATION INSTRUCTION PART NO 15307 KIT NO 3842 2015 & UP F-150 FRONT LEVELING KIT INSTALLATION READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. FAILURE TO ADHERE TO THE INSTRUCTIONS WILL VOID ANY GROUND FORCE

More information

2011 FORD SUPERDUTY F-250/350 4WD CSS-F3-9, CSS-F3-10 4.5 LIFT KIT

2011 FORD SUPERDUTY F-250/350 4WD CSS-F3-9, CSS-F3-10 4.5 LIFT KIT 14385 Veterans Way Moreno Valley, CA 92553 Phone: (951) 571-0212 Fax: (951) 571-0215 WWW.CSTSUSPENSION.COM 2011 FORD SUPERDUTY F-250/350 4WD CSS-F3-9, CSS-F3-10 4.5 LIFT KIT READ THE FOLLOWING NOTES PRIOR

More information

2011 F250 6 SUSPENSION KIT

2011 F250 6 SUSPENSION KIT 92156400 Thank you for choosing Rough Country for your suspension needs. 2011 F250 6 SUSPENSION KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

Installation manual. Long arm kit. 2003-20 Ram 2500 3500. Part # 30942

Installation manual. Long arm kit. 2003-20 Ram 2500 3500. Part # 30942 Installation manual Long arm kit 2003 2003-12 Ram 3500 Part # 30942 sj09032010rev.01 Part # 30942 2003-20 Ram 2500 3500 Long arm kit Part # Description Qty. 30940-01 Cross member bracket shim 4 30940-02

More information

2011-14 F250 6 RADIUS ARM KIT

2011-14 F250 6 RADIUS ARM KIT 92154000 Thank you for choosing Rough Country for your suspension needs. 2011-14 F250 6 RADIUS ARM KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

Installation manual. 2 front leveling kit. (Except Mega-Cab) Part # Part # Important customer information:

Installation manual. 2 front leveling kit. (Except Mega-Cab) Part # Part # Important customer information: Installation manual 2 front leveling kit 2014-2016 Dodge Ram 1500 4WD (Except Mega-Cab) Part # 32103 sj02252014rev.01 Part # 32103 2014-2016 Dodge Ram 1500 4WD (Except Mega-Cab) 2 front leveling kit Part

More information

INSTALLATION INSTRUCTIONS COMPETITION SERIES COILOVER SUSPENSION SYSTEM 03+ Scion xb

INSTALLATION INSTRUCTIONS COMPETITION SERIES COILOVER SUSPENSION SYSTEM 03+ Scion xb INSTALLATION INSTRUCTIONS COMPETITION SERIES COILOVER SUSPENSION SYSTEM 03+ Scion xb NOTE: Progress Technology products should only be installed by a qualified licensed mechanic experienced in the installation

More information

SCION tc 2005-2008 COIL OVER SUSPENSION Preparation

SCION tc 2005-2008 COIL OVER SUSPENSION Preparation SCION tc 2005-2008 COIL OVER SUSPENSION Preparation Part Number: PTR11-21070 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item # Quantity Reqd. Description

More information

Installation manual. 3 suspension system. 2009-2013 Ford F150. Part # 23000. Part # 23000. Important customer information: 2009-2013 Ford F150

Installation manual. 3 suspension system. 2009-2013 Ford F150. Part # 23000. Part # 23000. Important customer information: 2009-2013 Ford F150 Installation manual 3 suspension system 2009-2013 Ford F150 Part # 23000 sj12112012rev.03 Part # 23000 2009-2013 Ford F150 3 suspension system Part # Description Qty. 23000-01 Driver side upper control

More information

4.5 LIFT BOX KIT 2009 2013 DODGE RAM 2500 & 3500 4WD DIESEL ENGINE ONLY FTS23031

4.5 LIFT BOX KIT 2009 2013 DODGE RAM 2500 & 3500 4WD DIESEL ENGINE ONLY FTS23031 4.5 LIFT BOX KIT 2009 2013 DODGE RAM 2500 & 3500 4WD DIESEL ENGINE ONLY FTS23031 Fabtech Motorsports 4331 Eucalyptus Ave. Chino, CA 91710 Tech Line 909-597-7800 Fax 909-597-7185 Web www.fabtechmotorsports.com

More information

Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800. (installation performed on 60 Model) (Right) (Left)

Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800. (installation performed on 60 Model) (Right) (Left) 740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800 A (installation performed on 60 Model) Item Description Qty A Rotor 4 B Gear Box, L 2 C

More information

CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6

CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 Pre-Installation Notes: The CorkSport Rear Sway Bar is a great addition to improving the handling performance to the Mazdaspeed 6. It will minimize

More information

SCION tc LOWERING SPRINGS Preparation

SCION tc LOWERING SPRINGS Preparation Preparation Part Number: PTR11-21100 PTR11-21100-50 Kit Contents Item # Quantity Reqd. Description 1 2 Front Springs 2 2 Rear Springs 3 2 Locking Nuts 4 2 Spring Bumpers, Front 5 1 Instruction Form Hardware

More information

TJ Quick Disconnect Instructions

TJ Quick Disconnect Instructions 1 TJ Quick Disconnect Instructions www.teraflex.com Kit #17012 Kit #17092 Kit #17010 Kit #17090 Important Notes: Prior to beginning this or any installation read these instructions to familiarize yourself

More information

Installation manual. 2.5 suspension system. (Except Mega-Cab) Part # 32102. Part # 32102. Important customer information:

Installation manual. 2.5 suspension system. (Except Mega-Cab) Part # 32102. Part # 32102. Important customer information: Installation manual 2.5 suspension system 2009-2016 Dodge Ram 1500 4WD (Except Mega-Cab) Part # 32102 sj02272013rev.01 Part # 32102 2009-2016 Dodge Ram 1500 4WD (Except Mega-Cab) 2.5 Suspension System

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767 av1075 North Ave Sanger, CA 93657-3539 local: 559-875-8883 fax: 559-875-9883

More information

HOW - TO MAC-PHERSON STRUTS MAC-PHERSON STRUTS

HOW - TO MAC-PHERSON STRUTS MAC-PHERSON STRUTS HOW - TO MAC-PHERSON STRUTS MAC-PHERSON STRUTS Tool And Material Checklist Jack Stands or Hoist Lug Wrench Workbench Spanner or Pipe Wrench Torque Wrench Vise Vise-holding Tool Spring Compressor Oil Service

More information

Special Notes Before You Get Started

Special Notes Before You Get Started LIT-184 Installation Instructions 79-93 Fox Body Control Arm Bushing Style PN 200009 Congratulations on your purchase of AFCO Mustang Control Arms. We believe that you will agree that this system is second

More information

INSTALLATION INSTRUCTIONS: HARLEY-DAVIDSON SPORTSTER HI-OUTPUT GRENADES 2-INTO-2 PART# 16852/46852/16854/46854

INSTALLATION INSTRUCTIONS: HARLEY-DAVIDSON SPORTSTER HI-OUTPUT GRENADES 2-INTO-2 PART# 16852/46852/16854/46854 INSTALLATION INSTRUCTIONS: HARLEY-DAVIDSON SPORTSTER HI-OUTPUT GRENADES 2-INTO-2 PART# 16852/46852/16854/46854 Congratulations, you have purchased the finest exhaust system available for your motorcycle.

More information

Rize Industries, LLC. 2005/2006 Ford SuperDuty Installation Instructions Suspension Lift Kit Part# 410-306-042 & 410-308-042

Rize Industries, LLC. 2005/2006 Ford SuperDuty Installation Instructions Suspension Lift Kit Part# 410-306-042 & 410-308-042 2005/2006 Ford SuperDuty Installation Instructions Suspension Lift Kit Part# 410-306-042 & 410-308-042 While this kit is an easy bolt-on system, strongly recommends that a professional installation center

More information

Installation Instructions XRC Rocker Guards Part # 76872, 76871, 76861, 76862

Installation Instructions XRC Rocker Guards Part # 76872, 76871, 76861, 76862 NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included Qty Driver Side Rocker Guard 1 Passenger Side Rocker Guard 1 3/8 Counter-sunk Bolt 10 3/8 Flat

More information

Installation Instructions

Installation Instructions 85-3976 rev. 05 08-13 Installation Instructions Thank you for purchasing this antisway bar kit. Please read through these instructions before installation. Rear Anti-Sway Bar Kit for Dodge Ram Pick-Up

More information

ReadyLift (Part# ) Honda Pilot FWD/4WD Installation Instructions 2 Front/2 Rear

ReadyLift (Part# ) Honda Pilot FWD/4WD Installation Instructions 2 Front/2 Rear SAFETY WARNING:ReadyLift Suspension Inc. recommends this system be installed by a professional technician. In addition to these instructions, professional knowledge of disassembly/ reassembly procedures

More information

LL Nissan Xterra/Frontier 2 Front Leveling Kit PRO COMP SUSPENSION. Suspension Systems that Work!

LL Nissan Xterra/Frontier 2 Front Leveling Kit PRO COMP SUSPENSION. Suspension Systems that Work! 2360 Boswell Road Chula Vista, CA 91914 Phone 619.216.1444 Fax 619.216.1474 E-Mail tech@explorerprocomp.com PRO COMP SUSPENSION Suspension Systems that Work! LL-4010 2005-2008 Nissan Xterra/Frontier 2

More information

Nissan Xterra/Frontier 2 Front Leveling Kit PRO COMP SUSPENSION. Suspension Systems that Work!

Nissan Xterra/Frontier 2 Front Leveling Kit PRO COMP SUSPENSION. Suspension Systems that Work! 2360 Boswell Road Chula Vista, CA 91914 Phone 619.216.1444 Fax 619.216.1474 E-Mail tech@explorerprocomp.com PRO COMP SUSPENSION Suspension Systems that Work! 64502 2005-2006 Nissan Xterra/Frontier 2 Front

More information

Installation Instructions

Installation Instructions 85-4255 rev. 09 07-14 Installation Instructions Auxiliary Rear Anti- Sway Bar Kit for Sprinter 3500 part #1209-131 (1½" diameter) INTRODUCTION Thank you for purchasing this auxiliary anti-sway bar kit.

More information

Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Can-Am Commander

Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Can-Am Commander 740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Can-Am Commander A Item Description Qty A Rotor 4 B Gear Box, L 2 C Gear Box, R 2 D Gasket 4 E Cap 4 F Recessed

More information

»Product» Safety Warning

»Product» Safety Warning C1200 Installation Instructions 2007-2016 Chevy/GM 1500 2/4wd 2" Strut Spacer Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad

More information

Model A Turn Signal Kit Installation Guide

Model A Turn Signal Kit Installation Guide Model A Turn Signal Kit Installation Guide Consumer Hot Line: 888-471-LOGO 770-476-7322 In Atlanta, GA http://www.logolites.com P/N: 100-005/G 2003 3407 Hwy. 120 Duluth, GA 30096, USA Logo Lites and the

More information

Installation Instructions READ INSTALLATION INSTRUCTIONS IN ITS ENTIRETY BEFORE INSTALLING YOUR COIL-RITE KIT

Installation Instructions READ INSTALLATION INSTRUCTIONS IN ITS ENTIRETY BEFORE INSTALLING YOUR COIL-RITE KIT 4124 / 4125 / 4135 4142 / 4324 / 4173 Installation Instructions READ INSTALLATION INSTRUCTIONS IN ITS ENTIRETY BEFORE INSTALLING YOUR COIL-RITE KIT SWAY BAR LINKAGE LOCATED FORWARD OF THE AXLE MOUNTED

More information

Kit Includes: 4 Door Jeep Wrangler: Marker Tape Drill. 1 Left Door Check Strap/Arm 1 Left Hinge Plate 1 Right Door Check Strap/Arm

Kit Includes: 4 Door Jeep Wrangler: Marker Tape Drill. 1 Left Door Check Strap/Arm 1 Left Hinge Plate 1 Right Door Check Strap/Arm Smart Door Installation Instructions PRODU UCT INSTALL LATION GUI IDE Prior to beginning this or any installation, completely read these instructions to familiarize yourself with the required steps and

More information

Installation Instructions Complete Top Frame & Hardware With Soft Upper Doors Jeep Wrangler

Installation Instructions Complete Top Frame & Hardware With Soft Upper Doors Jeep Wrangler Installation Instructions Complete Top Frame & Hardware With Soft Upper Doors 87-95 Jeep Wrangler IMPORTANT NOTICE: Carefully read instructions before attempting to install this product. Rampage Products

More information

INSTRUCTION BOOK FOR. Single Monitor Video Conference Cart

INSTRUCTION BOOK FOR. Single Monitor Video Conference Cart INSTRUCTION BOOK FOR Single Monitor Video Conference Cart Procedure 1. Remove contents from cartons and examine for damaged or missing parts. The keys for the cabinet doors are tied to the outside of the

More information

Installation Guide 2010 BMW S1000RR Full Exhaust System

Installation Guide 2010 BMW S1000RR Full Exhaust System Installation Guide 2010 BMW S1000RR Full Exhaust System!! THIS PRODUCT IS DESIGNED FOR USE IN CLOSED COURSE RACING AND IS NOT INTENDED FOR HIGHWAY USE!! Congratulations on the purchase of your new TaylorMade

More information

M-FR3-FAEB Fiesta Suspension INSTALLATION INSTRUCTIONS

M-FR3-FAEB Fiesta Suspension INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

Installation manual. 4 suspension system. 2014-2016 Chevy or GMC 1500 4WD. Part # 14059. Part # 14059. Important customer information:

Installation manual. 4 suspension system. 2014-2016 Chevy or GMC 1500 4WD. Part # 14059. Part # 14059. Important customer information: Installation manual 4 suspension system 2014-2016 Chevy or GMC 1500 4WD Part # 14059 sj09052013rev.01 Part # 14059 2014-2016 Chevy or GMC 1500 4WD 4 suspension system Part # Description Qty. 14056-01 Upper

More information

07 & UP GM 1500 PICKUP, TAHOE, YUKON, SUBURBAN, AVALANCHE FRONT 2.0 LEVELING KIT INSTALLATION

07 & UP GM 1500 PICKUP, TAHOE, YUKON, SUBURBAN, AVALANCHE FRONT 2.0 LEVELING KIT INSTALLATION INSTRUCTION PART NO 15282 LEVELING KIT NO 3812P 07 & UP GM 1500 PICKUP, TAHOE, YUKON, SUBURBAN, AVALANCHE FRONT 2.0 LEVELING KIT INSTALLATION READ INSTRUCTIONS/WARNINGS COMPLETELY THROUGH BEFORE STARTING.

More information

ReadyLift (Part# 66-5075) Strut Extension, Installation Instructions Toyota Tundra New Body Style 2WD & 4WD

ReadyLift (Part# 66-5075) Strut Extension, Installation Instructions Toyota Tundra New Body Style 2WD & 4WD SAFETY WARNING: recommends this system be installed by a professional technician. In addition to these instructions, professional knowledge of disassembly/ reassembly procedures and post installation checks

More information

LIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions

LIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions LIFT-505 BMF Lift Kit Yamaha Drive Gas or Electric Installation Instructions Contents of LIFT-505 Yamaha Drive BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger

More information

James Barone Racing Aftermarket Parts and Accessories

James Barone Racing Aftermarket Parts and Accessories Page1 James Barone Racing Aftermarket Parts and Accessories 2013+ Focus ST Passenger Mount Installation Instructions What you will need: Jack and jack stands. Jack stands are preferred Ramps will work

More information

Installation Instructions

Installation Instructions 85-3180 rev. 07 03-14 Installation Instructions Thank you for purchasing this antisway bar kit. Please read through these instructions before installation. Front Anti-Sway Bar Kit for the Ford E350/450

More information

Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 900 Crew. (Right) (Left)

Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 900 Crew. (Right) (Left) 740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 900 Crew A Item Description Qty A Rotor 4 B Gear Box, L 2 C Gear Box, R 2 D Gasket 4 E Cap

More information

High Lifter Products, Inc. (318) N Professional Drive Fax (318) Shreveport, LA 71105

High Lifter Products, Inc. (318) N Professional Drive Fax (318) Shreveport, LA 71105 High Lifter Products, Inc. (318) 524-2270 780 N Professional Drive Fax (318) 524-2297 Shreveport, LA 71105 Kawasaki Mule Lift Kit Installation Instructions Mule 2500, 3000, 3010, and 3020 Read Before Installation!

More information

Installation Instructions

Installation Instructions 85-3857 rev. 04 03-16 Installation Instructions Thank you for purchasing this antisway bar kit. Please read through these instructions before installation. Front Anti-Sway Bar TruTrac Bar Combo Kit for

More information

Part # 11060210 59-64 Impala SA CoilOver Suspension Package

Part # 11060210 59-64 Impala SA CoilOver Suspension Package 350 S. St. Charles St. Jasper, In. 47546 Part # 11060210 59-64 Impala SA CoilOver Suspension Package Front Components: 1 11053510 HQ Series Front Coilovers 1 11052899 Front Lower StrongArms 1 11053699

More information

DIY Dinan Springs Install on a 2012 BMW F30 335i

DIY Dinan Springs Install on a 2012 BMW F30 335i DIY Dinan Springs Install on a 2012 BMW F30 335i Rear Springs / bump stops: 1. Break loose rear lug nuts (17 mm), chock front wheels, jack up rear and support with jack stands. Remove wheel. 2. Remove

More information

Tech Line: /5415 Front Strut Frame Installation 2 x3 Box Frame Rails and 1-5/8 Round Tube

Tech Line: /5415 Front Strut Frame Installation 2 x3 Box Frame Rails and 1-5/8 Round Tube Tech Line: 1-561-863-2188 5410/5415 Front Strut Frame Installation 2 x3 Box Frame Rails and 1-5/8 Round Tube These instructions are just one way of properly installing a strut front suspension. Depending

More information

Table of Contents WARNING SYMBOLS AND DEFINITIONS

Table of Contents WARNING SYMBOLS AND DEFINITIONS Table of Contents SAFETY INSTALLATION OPERATION MAINTENANCE Safety... 2 Specifications... 4 Installation... 5 Operation... 8 WARNING SYMBOLS AND DEFINITIONS Maintenance... 9 Parts List and Assembly Diagram...

More information

Owner s Manual Read and keep this manual. Patents World Wide

Owner s Manual Read and keep this manual. Patents World Wide Owner s Manual Read and keep this manual. Patents World Wide S & S Industries, Inc., Sarasota, FL, USA www.trail-gator.com Copyright 2008 All Rights Reserved The following manual is provided to assist

More information

Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 1000 (2015) (Right) (Left)

Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 1000 (2015) (Right) (Left) 740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 1000 (2015) A Item Description Qty A Rotor 4 B Gear Box, L 2 C Gear Box, R 2 D Gasket 4 E

More information

Table of Contents. Technical Information Warning Statement

Table of Contents. Technical Information Warning Statement Table of Contents Technical Information-----------------------------------1 Warning Statement--------------------------------------2 Read Before Riding-------------------------------------3 List Of Parts-----------------------------------------------4

More information

Installation Instructions: (Part # SB76880) XRC Armor Front Fender Kit

Installation Instructions: (Part # SB76880) XRC Armor Front Fender Kit WARNING: Check with Local and State laws before installing this accessory! NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included: Qty Parts Included:

More information

Installation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab

Installation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab GOOSENECK MOUNTING KIT Equipment Required: Fastener Kit: F Wrenches: 3/4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers

More information

SUT-200-S RUNNING GEAR CONVERSION TO SUT-220-S

SUT-200-S RUNNING GEAR CONVERSION TO SUT-220-S SUT-200-S RUNNING GEAR CONVERSION TO SUT-220-S Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16, and 7/8 sockets.

More information

Sidekick / Tracker Solid Axle Suspension 2 Door Installation Instructions

Sidekick / Tracker Solid Axle Suspension 2 Door Installation Instructions 1031 Narregan St. * Medford, OR 97501 * 1-877-789-8547 * www.trailtough.com Disassembly Sidekick / Tracker Solid Axle Suspension 2 Door Installation Instructions 1. Lift vehicle and support by frame &

More information

Installation Manual TWM Performance Short Shift Kit 2005 and up Scion TC

Installation Manual TWM Performance Short Shift Kit 2005 and up Scion TC Installation Manual TWM Performance Short Shift Kit 2005 and up Scion TC 1. Unscrew the shift knob by rotating counter clockwise, set it aside for now. 2. Remove the portion of the console with the shift

More information

INSTRUCTION S G-Comp Front Suspension: Chevy Nova Speedway Motors, Inc. 2015

INSTRUCTION S G-Comp Front Suspension: Chevy Nova Speedway Motors, Inc. 2015 INSTRUCTION S 350-100 G-Comp Front Suspension: 62-67 Chevy Nova Speedway Motors, Inc. 2015 Kit Contents: 91035700 G-Comp Bare Subframe 350101 G-Comp Support Tubes 91035702 G-Comp Front Subframe Hardware

More information

Trailer Receiver Hitch Installation Instructions

Trailer Receiver Hitch Installation Instructions Model/Applications: Hitch Part #: 1003, 1004, 1007, 1008 R56 07-14 Mini Cooper S Hardtop R57 09-15 Mini Cooper S Convertible R58 10-15 Mini Cooper S Coupe R59 11-15 Mini Cooper S Roadster Hitch Capacity:

More information

INSTRUCTION BOOK FOR. Dual Monitor Video Conferencing Cart

INSTRUCTION BOOK FOR. Dual Monitor Video Conferencing Cart INSTRUCTION BOOK FOR Dual Monitor Video Conferencing Cart Procedure 1. Remove contents from cartons and examine for damaged or missing parts. The keys for the cabinet doors are tied to the outside of the

More information

KDT916 - Watts Link - Complete Assembly

KDT916 - Watts Link - Complete Assembly KDT916 - Watts Link - Complete Assembly Please read all instructions carefully prior to installation and verify all kit contents and tools are on hand prior to installation. Professional Installation by

More information

HYDRAULIC LIFT TABLE 1/4-TON CAPACITY. Specifications Hydraulic Lift Table Unpacking. Important Safety Information

HYDRAULIC LIFT TABLE 1/4-TON CAPACITY. Specifications Hydraulic Lift Table Unpacking. Important Safety Information Specifications 1/4-TON CAPACITY HYDRAULIC LIFT TABLE 94822 Hydraulic Lift Table Instructions and precautions Unpacking Capacity: 500 Lbs. Maximum Maximum Table Height: 27-1/4 Minimum Table Height 9 Table

More information

Ford Racing Mustang C-Springs Installation Guide (1979-2004)

Ford Racing Mustang C-Springs Installation Guide (1979-2004) Ford Racing Mustang C-Springs Installation Guide (1979-2004) The below installation instructions work for the following products: Ford Racing Springs (Mustang C-Springs 1979-2004) Please read through the

More information

INSTALLATION INSTRUCTIONS 65-72 F-100 4-Link Rear End

INSTALLATION INSTRUCTIONS 65-72 F-100 4-Link Rear End INSTALLATION INSTRUCTIONS 65-72 F-100 4-Link Rear End Please read these instructions completely before starting your installation. Assemble suspension on vehicle before powder-coating to ensure proper

More information

Spring Installation (Eibach)

Spring Installation (Eibach) Spring Installation (Eibach) From Nissan 350Z Wiki Just finished my install of Eibach Pro-Kit springs on my Coupe. I did it one tire at a time. Torque spec on tire lugnuts: 80ft/lb. The following is a

More information

Strut spring replacement procedure by mbtoloczko

Strut spring replacement procedure by mbtoloczko Strut spring replacement procedure by mbtoloczko *Pre-job prep* 1) About a week before you plan to do the work, pull off all the wheels, clean the exposed threads on the strut-to-knuckle bolts using a

More information

StowAway Bike Rack Assembly Instructions Rev For Swingaway and Fixed Frame Bike Rack and Bike Cargo Rack Models

StowAway Bike Rack Assembly Instructions Rev For Swingaway and Fixed Frame Bike Rack and Bike Cargo Rack Models StowAway Bike Rack Assembly Instructions Rev. 0610 For Swingaway and Fixed Frame Bike Rack and Bike Cargo Rack Models Please review the instructions and warranty carefully before assembling the unit. Assembly

More information

MUSTANG II IFS COMPLETE PARTS PACKAGE

MUSTANG II IFS COMPLETE PARTS PACKAGE MUSTANG II IFS COMPLETE PARTS PACKAGE Your Southern Rods & Parts Mustang II IFS Parts Package contains the following items: 1 pr) Upper Control Arms (2023) 1) Upper Arm Bolt Kit (MP-001-A) 1 pr) Lower

More information

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS. 2012-2015 BMW 335i 3.0L

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS. 2012-2015 BMW 335i 3.0L Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS 2012-2015 BMW 335i 3.0L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2057DK AIR FILTER 1 2 9-0442 TUBE;

More information

Owner s Manual & Safety Instructions

Owner s Manual & Safety Instructions Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, installation, operating, inspection, maintenance and cleaning procedures. Write the product

More information

Trailer Receiver Hitch Installation Instructions

Trailer Receiver Hitch Installation Instructions Model/Applications: 1004: R56 07-10 Mini Cooper Hatch R57 09-10 Mini Cooper Convertible 1003: R5 07-10 Mini Cooper S Hatch and 09-10 Mini Cooper S Convert Hitch Capacity 1400 lbs gross, 200 lb max tongue

More information

CX200S SLIDING TABLE ATTACHMENT FOR TABLE SAW User Manual

CX200S SLIDING TABLE ATTACHMENT FOR TABLE SAW User Manual CX00S SLIDING TABLE ATTACHMENT FOR TABLE SAW User Manual GENERAL SAFETY INSTRUCTIONS FOR MACHINES Extreme caution should be used when operating all power tools. Know your power tool, be familiar with its

More information

INSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES

INSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY

More information

2007 Hummer H SUSPENSION Front Suspension - H3

2007 Hummer H SUSPENSION Front Suspension - H3 2007 SUSPENSION Front Suspension - H3 SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Application Hub and Bearing Assembly to Steering Knuckle Bolts Lower Control Arm

More information

Installation Instructions

Installation Instructions May 2, 2016 1967-1969 Camaro and 1968-74 Nova Complete Sub Frame Installation Instructions The following instructions are intended for professional installers and are guidelines only. Speedtech Performance

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 2011-16 GM C/K2500HD & C/K3500HD 4 ULTIMATE SYSTEM FTS21104 Fabtech Motorsports 4331 Eucalyptus Ave. Chino, CA 91710 Tech Line: 909-597-7800 Fax: 909-597-7185 Web: www.fabtechmotorsports.com

More information

Please visit for the latest version of these installation instructions.

Please visit  for the latest version of these installation instructions. Please visit www.blueox.com for the latest version of these installation instructions. BX2639 2013-16 Ford C-Max (Includes Hybrid & Energi) Attachment Tab Height: 12 Serial Number Attachment Tab Width:

More information

Supercharger Reduction Pulley Install Instructions for MINI Cooper S

Supercharger Reduction Pulley Install Instructions for MINI Cooper S Page 1 of 8 Technical Service For any technical advice concerning this product or its installation, call our Support Line at: 903-581-1855 PROMINI / BMP Design Inc. 3208 Park Center Drive Tyler, Texas,

More information

AWE Tuning Air/Air Intercooler Kit for 2000-04 Audi 2.7T

AWE Tuning Air/Air Intercooler Kit for 2000-04 Audi 2.7T AWE Tuning Air/Air Intercooler Kit for 2000-04 Audi 2.7T Congratulations on your purchase of the AWE Tuning Intercoolers for your 2.7T Audi. Hundreds of hours of design and operational testing were spent

More information

Part # Toyota 4WD IFS Stage II PRO COMP SUSPENSION. Suspension Systems that Work!

Part # Toyota 4WD IFS Stage II PRO COMP SUSPENSION. Suspension Systems that Work! 2360 Boswell Road Chula Vista, CA 91914 Phone 619.216.1444 Fax 619.216.1474 E-Mail tech@explorerprocomp.com PRO COMP SUSPENSION Suspension Systems that Work! Part # 57289 Toyota 4WD IFS Stage II 86-95

More information

92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540

92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540 92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540 www.airliftperformance.com MN-514 (06409) NPR 4762 Please read these instructions completely before proceeding with installation

More information

INSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113)

INSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE

More information

INSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES

INSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES INSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES DEALER/INSTALLER: (1) Provide this Manual to end user. END USER: (1) Save this Manual for future reference. (2) Pass on copies of Manual to any other

More information

DIY (Do It Yourself ) Installation Instructions

DIY (Do It Yourself ) Installation Instructions DIY (Do It Yourself ) Installation Instructions DIY Kit Parts: Tools Required: #1 & #2 Phillips head screwdrivers Two 2.5 mm allen wrenches Needle-nose pliers Small flat blade screwdriver 10 mm wrench

More information

IMPORTANT SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION Table of Contents SAFETY INSTALLATION OPERATION INSPECTION Specifications... 1 Safety... 2 Installation... 4 Operation... 5 WARNING SYMBOLS AND DEFINITIONS Maintenance... 6 Parts List and Assembly Diagram...

More information

6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included:

6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included: Revised May 205 6-08/6-09 6 inch A-Arm Lift Kit will fit CLUB CAR DS installation instructions included: Rear Lift Blocks Main Suspension Assembly Spindles A-Arms Rear Shock Mounting Plates U-Bolts WARNING:

More information

Front brakes (FN- 3), servicing

Front brakes (FN- 3), servicing j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly

More information

SLACK PERFORMANCE KARTS

SLACK PERFORMANCE KARTS SLACK PERFORMANCE KARTS SET UP GUIDE Thank you for purchasing a 2013 Slack Axiom Chassis. Performance Mfg. strives to provide you with the very best chassis and components on the market today. Your satisfaction

More information

2014+ Mazda 3/6 Shift Knob Installation Instructions

2014+ Mazda 3/6 Shift Knob Installation Instructions Page1 James Barone Racing Aftermarket Parts and Accessories 2014+ Mazda 3/6 Shift Knob Installation Instructions What you will need: Your hands 15mm deep socket Socket wrench Ok let s get started. 1. Remove

More information

Mini Cooper and S Trailer Receiver Hitch Installation Instructions

Mini Cooper and S Trailer Receiver Hitch Installation Instructions Application Mini Cooper and S 3 Door Hatch or Convertible; M1001-02-06 Mini Cooper M1002-02-06 Mini Cooper S Hitch Capacity 1400 lbs gross, 200 lb max tongue Notes: This hitch features a removable ball

More information

Installation Instructions

Installation Instructions Installation Instructions 1501100 Ladder Rack Before Assembling: Before assembling your Buyers ladder rack it s important to read, understand, and follow all listed instructions. Note: There are two different

More information

Installation Instructions and Warranty Information

Installation Instructions and Warranty Information Installation Instructions and Warranty Information For JBA Headers for 1995-2003 Toyota Tacoma 3.4L and 1995-1998 T-100 V-6 P/N 2032 2001-2003 Tacoma 3.4L P/N 2032-1 1995-2000 Tacoma 3.4L P/N 2032-3 1995-1998

More information

JK 2.5 Install Kit Instruction Pack

JK 2.5 Install Kit Instruction Pack 1 JK 2.5 Install Kit Instruction Pack www.teraflex.com Contents: Rear Sway Bar Link Instructions Spring Instructions Bumpstop Instructions Rear Track Bar Bracket Instructions Rear Lower Spring Retainer

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS DURAMAX POWER STEERING LINES 01-10 6.6L DURAMAX DIESEL 2500 / 3500 TRUCKS INSTALLATION INSTRUCTIONS Thank You for purchasing the Driven Diesel High Pressure Power Steering Line kit for the 2001-2010 GM

More information