Tech Note 166 How to Set Up Two Ethernet Network Cards for InControl

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Tech Note 166 How to Set Up Two Ethernet Network Cards for InControl"

Transcription

1 Tech Note 166 How to Set Up Two Ethernet Network Cards for InControl All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information. Topic#: C reated: January 7, 2000 Wonderware InControl allows your hardware control computer to connect to your existing network and to control your Ethernet- based I/O devices with two Ethernet network cards. This Tech Note shows how to configure your Windows NT 4.0 system for two Ethernet network cards. Procedure 1. Double- click the Network icon under the Control Panel. Click the Protocols tab, as shown in figure 1. FIGURE 1. NETWORK PROTOCOLS ALREADY INSTALLED FOR INCONTROL You should already have these network protocols installed, as shown in figure 1: NetBEUI Protocol NWLink IPX/SPX Compatible Transport NWLink NetBIOS 1/6

2 TCP/IP Protocol Note If you don t have all four protocols installed, click Add on the Network dialog box to install them. 2. Click the Adapters tab on the Network dialog box. If you ve already installed and configured your two network cards, you should see the cards listed as shown in the example in figure 2. FIGURE 2. EXAMPLE OF TWO INSTALLED NETWORK CARDS AS LISTED IN CONTROL PANEL Note If you don't see either or both network cards listed in the Network dialog box, go back and install the cards and their device drivers according to the card s manufacturer before continuing with this procedure. Select the card from the Network dialog box that s configured to communicate with the I/O devices and click Properties. (The format of the Adapter Properties dialog box that appears will depend on the type of card that you ve selected.) Ensure that the card s duplex speed is set to Half Duplex. The card s network speed should be set to an appropriate value for your network. (If Full Duplex is chosen, network collisions will occur and will affect the performance of the network driver and InControl. InControl needs higher scan times and, thus, there s a greater possibility for scan overruns.) If your network card offers an AutoDetect Connection option, select this option as the default. 2/6

3 3. Set up an IP address for each network card by clicking the Protocols tab again. Select TCP/IP Protocol, then click Properties. The Microsoft TCP/IP Properties dialog box will appear as shown in figure 3. FIGURE 3. TCP/IP PROPERTY DIALOG BOX If the card will communicate with the network (that is, it s a network card), select Obtain an OP address from a DHCP server. If the card will communicate with the I/O devices (that is, it s an I/O card), select Specify an IP address. Make sure to type in the correct IP address and Subnet Mask for your network if you specified an IP address. (Contact your site s network administrator for more information.) Click OK to complete the IP address configuration. 4. With the Protocols tab still on top on the Network dialog box, select NWLink IPX/SPX Compatible Transport and click Properties. The NWLink IPX/SPX Properties dialog box will appear as shown in figure /6

4 FIGURE 4. PROPERTIES FOR NWLINK IPX/SPX COMPATIBLE TRANSPORT Select Adapter for the network card that will communicate with the I/O hardware. Select Auto Detect for the Frame Type. Then click OK. 5. Click the Bindings tab on the Network dialog box and display the bindings for all protocols as shown in figure /6

5 FIGURE 5. BINDINGS FOR ALL PROTOCOLS The following six protocols should be listed along with their configurations: NetBEUI Protocol - Enable network card only NWLink IPX/SPX Compatible Transport - Enable I/O card only NWLink NetBIOS - No cards should be enabled NWLink SPX Protocol - No cards should be enabled TCP/IP Protocol - Enable network card and I/O card WINS Client (TCP/IP) - Enable network card only Click Close when complete. The bindings and protocol settings will be updated. Reboot the computer when prompted. 6. Test the network card connections to the I/O devices by running the program Automationdirect.com and using the NetEdit feature. Note You can obtain the Automationdirect.com program from your network card s manufacturer. If NetEdit is unable to communicate to the connected devices, you ll need to set the IP address for each device. You can do this either in NetEdit or under InControl s Edit/Create Base menu. The IP address may be set as a subset of the IP address for the Ethernet adapter used to communicate with the I/O hardware. For example, if the I/O card s IP address is , then the device s IP address can be , with the last number 10 being the same as the module ID that s listed in InControl's Create Base dialog box. 5/6

6 C. Sparks The Tech Note is published occasionally by Wonderware Technical Support. Editors: Sabrina Abercromby and Kelly Hauser; Publisher: Wonderware C orporation, 100 Technology Drive, Irvine C A There is also technical information on our software products at Wonderware Technical Support, our WonderFax fax-ondemand system at (949) , and the C omprehensive Support Knowledge Base. For technical support questions, send an to back to top 2013 Wonderware C orporation. All rights reserved. Terms of Use. 6/6

Installing the TCP/IP Network Protocol

Installing the TCP/IP Network Protocol Tech Note 120 Configuring the GEHCS I/O Server for Windows NT All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

More information

Tech Note 53 Configuring the Siemens SINEC H1 CP1413 for Windows NT

Tech Note 53 Configuring the Siemens SINEC H1 CP1413 for Windows NT Tech Note 53 Configuring the Siemens SINEC H1 CP1413 for Windows NT All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

More information

Tech Note 137 Configuring the H1CP1413 I/O Server, Version 7.1 or Later

Tech Note 137 Configuring the H1CP1413 I/O Server, Version 7.1 or Later Tech Note 137 Configuring the H1CP1413 I/O Server, Version 7.1 or Later All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

More information

8/23/13 Configuring the S7 I/O Server to Access S7 PLC s via Industrial Ethernet (ISO) and a Standard Ethernet Card for Windows NT 4.

8/23/13 Configuring the S7 I/O Server to Access S7 PLC s via Industrial Ethernet (ISO) and a Standard Ethernet Card for Windows NT 4. Tech Note 195 Configuring the S7 I/O Server to Access S7 PLC s via Industrial Ethernet (ISO) and a Standard Ethernet Card for Windows NT 4.0 All Tech Notes and KBCD documents and software are provided

More information

Creating DTS Packages

Creating DTS Packages Tech Note 212 Using DTS to Transfer Historical Data from InSQL to Other Systems All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for

More information

8/23/13 Configuring the S7 I/O Server for Windows 95 to Access S7 PLCs Via the Profibus Network

8/23/13 Configuring the S7 I/O Server for Windows 95 to Access S7 PLCs Via the Profibus Network Tech Note 110 Configuring the S7 I/O Server for Windows 95 to Access S7 PLCs Via the Profibus Network All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See

More information

Tech Note 132 Using FactorySuite 2000s WWClient to Check I/O Server Communications

Tech Note 132 Using FactorySuite 2000s WWClient to Check I/O Server Communications Tech Note 132 Using FactorySuite 2000s WWClient to Check I/O Server Communications All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use

More information

Tech Note 128 Configuring InBatch For Standalone PCs With SQL Server and IndustrialSQL Server

Tech Note 128 Configuring InBatch For Standalone PCs With SQL Server and IndustrialSQL Server Tech Note 128 Configuring InBatch For Standalone PCs With SQL Server and IndustrialSQL Server All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms

More information

8/23/13 Configuring the S7 Server for Windows NT 4.0 to Access S7-400 PLCs via the Siemens CP1613 Card for ISO (Industrial Ethernet)

8/23/13 Configuring the S7 Server for Windows NT 4.0 to Access S7-400 PLCs via the Siemens CP1613 Card for ISO (Industrial Ethernet) Tech Note 224 Configuring the S7 Server for Windows NT 4.0 to Access S7-400 PLCs via the Siemens CP1613 Card for ISO (Industrial Ethernet) All Tech Notes and KBCD documents and software are provided "as

More information

Tech Note 213 Finding Memory Leaks in Windows 95/98/98SE Using System Monitor

Tech Note 213 Finding Memory Leaks in Windows 95/98/98SE Using System Monitor Tech Note 213 Finding Memory Leaks in Windows 95/98/98SE Using System Monitor All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for

More information

All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

All Tech Notes and KBCD documents and software are provided as is without warranty of any kind. See the Terms of Use for more information. Tech Note 115 Overview of the InTouch 7.0 Windows NT Services All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

More information

Tech Note 692 Using Virtual SMTP Server for SCADAlarm Notifications

Tech Note 692 Using Virtual SMTP Server for SCADAlarm  Notifications Tech Note 692 Using Virtual SMTP Server for SCADAlarm Email Notifications All Tech Notes, Tech Alerts and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of

More information

Section 1 - Configuring the Siemens Simatic Net Software

Section 1 - Configuring the Siemens Simatic Net Software Tech Note 220 Configuring the S7 Server for MPI or Profibus Communications for Windows NT 4.0 to Access S7-400 PLCs via the Siemens CP5613 Card All Tech Notes and KBCD documents and software are provided

More information

Installing the Microsoft Network Driver Interface

Installing the Microsoft Network Driver Interface Installing the Microsoft Network Driver Interface Overview This guide explains how to install the PictureTel Live200 Microsoft Network Driver Interface (NDIS) software you have downloaded from PictureTel's

More information

Print Server. Quick Installation Guide

Print Server. Quick Installation Guide Print Server Quick Installation Guide Table of Contents INTRODUCTION... 1 INSTALL THE HARWARE... 2 INSTALL UTILITIES FOR WINDOWS 95/98... 3 CONFIGURE THE PRINT SERVER... 4 Network environment without file

More information

TABLE OF CONTENTS. PRELIMINARY SETUP REQUIREMENTS... 1 Minimum Hardware/Software Requirements...1

TABLE OF CONTENTS. PRELIMINARY SETUP REQUIREMENTS... 1 Minimum Hardware/Software Requirements...1 Worldspan RemoteLink Setup and Configuration Procedures for Worldspan Go! SM Dynamic IP Address TABLE OF CONTENTS PRELIMINARY SETUP REQUIREMENTS... 1 Minimum Hardware/Software Requirements...1 SETUP AND

More information

8/23/13 Configuring the Wonderware SECS-II/GEM Host Creator (SERIAL-RS232)

8/23/13 Configuring the Wonderware SECS-II/GEM Host Creator (SERIAL-RS232) Tech Note 202 Configuring the Wonderware SECS-II/GEM Host Creator (SERIAL- RS232) All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use

More information

Tech Note 266 How to Send and SMS Messages Using SCADAlarm 5.0.3.xxx

Tech Note 266 How to Send  and SMS Messages Using SCADAlarm 5.0.3.xxx Tech Note 266 How to Send email and SMS Messages Using SCADAlarm 5.0.3.xxx All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more

More information

Connecting to a Soundweb TM. London Network

Connecting to a Soundweb TM. London Network This guide will step you through the process of configuring your laptop and HiQnet TM London Architect TM to communicate with a network of Soundweb London devices. 1 Install London Architect Install the

More information

Configuration Management

Configuration Management CHAPTER36 Cisco SDM allows you to edit the router configuration file and to reset the router configuration to factory defaults. Because editing the configuration file directly and resetting the router

More information

Enabling Cross-Machine Distributed Transactions (via MSDTC)

Enabling Cross-Machine Distributed Transactions (via MSDTC) Tech Note 557 Enabling Cross-Machine Distributed Transactions Between Factelligence Nodes All Tech Notes, Tech Alerts and KBCD documents and software are provided "as is" without warranty of any kind.

More information

Connect Serial Cable from Terminal Blocks to Computer Comport for Bridge Configuration

Connect Serial Cable from Terminal Blocks to Computer Comport for Bridge Configuration Tech Note 391 Configuring Modicon Modbus to Ethernet Bridge 170-CEV-300-10 All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more

More information

Configure SPLM 2012 on Windows 7 Laptop

Configure SPLM 2012 on Windows 7 Laptop Configure SPLM 2012 on Windows 7 Laptop 7/12/2012 SmartPlant License Manager (SPLM) requires a static IP Address on the license machine. To fulfill this requirement on laptops a virtual network adapter

More information

Guide to Setting up Internet Connection Sharing for Windows

Guide to Setting up Internet Connection Sharing for Windows Guide to Setting up Internet Connection Sharing for Windows Document Date: December 20, 2005 Document Version: Version: 1.0 Disclaimer: Please note that this document is provided on an as is where is basis

More information

Windows Vista: Connecting to the fastnsecure@hood wireless network at Hood College

Windows Vista: Connecting to the fastnsecure@hood wireless network at Hood College Windows Vista: Connecting to the fastnsecure@hood wireless network at Hood College Please ensure your computer meets the following criteria in order to successfully make a connection to this network: 802.11n

More information

All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

All Tech Notes and KBCD documents and software are provided as is without warranty of any kind. See the Terms of Use for more information. Tech Note 365 Working with InTouch I/O Tags in InControl All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information. Topic#:

More information

Interfacing Basler GigE Cameras With Cognex VisionPro 7.2

Interfacing Basler GigE Cameras With Cognex VisionPro 7.2 www.baslerweb.com Interfacing Basler GigE Cameras With Cognex VisionPro 7.2 This Application Note explains how to interface a Basler camera with GigE interface with the Cognex VisionPro 7.2 software package

More information

Configuring the OfficeConnect Secure Gateway for a remote L2TP over IPSec connection

Configuring the OfficeConnect Secure Gateway for a remote L2TP over IPSec connection Creating L2TP over IPSec VPNs between the OfficeConnect Cable/DSL Secure Gateway and the Microsoft VPN Client 1.0 Introduction The OfficeConnect Cable/DSL Secure Gateway supports IPSec, PPTP and L2TP over

More information

This module shows how the ethernet connection is configured and the activation of a soft-key in the program manager area.

This module shows how the ethernet connection is configured and the activation of a soft-key in the program manager area. Sinumerik B045 Network configuration Module Description: The 828D controller is equipped with a configurable ethernet interface (X130). This interface can be used for service/commissioning work. A soft-key

More information

Tech Note 973 Configuring Permissions for the Intelatrac Attached Document Directory

Tech Note 973 Configuring Permissions for the Intelatrac Attached Document Directory Tech Note 973 Configuring Permissions for the Intelatrac Attached Document Directory All Tech Notes, Tech Alerts and KBCD documents and software are provided "as is" without warranty of any kind. See the

More information

Palomar College Dial-up Remote Access

Palomar College Dial-up Remote Access Palomar College Dial-up Remote Access Instructions for Windows 95/98 and Windows 2000 Following are instructions to implement dialup access to the Palomar College network, email and Internet. The minimum

More information

Identifying a Corrupted Application

Identifying a Corrupted Application Tech Note 112 Recovering a Corrupted InTouch Application All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information. Topic#:

More information

Internet for Everyone In-Room Instructions January 2011 Version 1.3

Internet for Everyone In-Room Instructions January 2011 Version 1.3 Internet for Everyone In-Room Instructions January 2011 Version 1.3 Everywhere Internet 2006 Page 1 of 17 Connecting your computer to the Everywhere Internet network in your room 1. You need a network

More information

How to Connect to the Internet in Windows 95

How to Connect to the Internet in Windows 95 How to Connect to the Internet in Windows 95 95 WINDOWS kbtool The information in this article applies to: Microsoft Windows 95 SUMMARY Last reviewed: December 11, 1997 Article ID: Q138789 This article

More information

Software Installation Guide

Software Installation Guide Software Installation Guide This manual explains how to install the software over a USB or network connection. Network connection is not available for models SP 200/200S/203S/203SF/204SF. Flowchart The

More information

Deploying Windows Streaming Media Servers NLB Cluster and metasan

Deploying Windows Streaming Media Servers NLB Cluster and metasan Deploying Windows Streaming Media Servers NLB Cluster and metasan Introduction...................................................... 2 Objectives.......................................................

More information

HYPERLINK Internet PC setup guide. HYPERLINK Internet support helpdesk at 1-866-302-5525.

HYPERLINK Internet PC setup guide. HYPERLINK Internet support helpdesk at 1-866-302-5525. HYPERLINK Internet support helpdesk at 1-866-302-5525. Congratulations on your new residence and welcome to HYPERLINK Internet service. In a few short moments you will be connected to one of the fastest

More information

All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

All Tech Notes and KBCD documents and software are provided as is without warranty of any kind. See the Terms of Use for more information. Tech Note 211 Configuring Microsoft FrontPage Server Extensions All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

More information

WORKSTATION CONFIGURATION FOR NEW GALILEO MANAGED VPN SITES

WORKSTATION CONFIGURATION FOR NEW GALILEO MANAGED VPN SITES WORKSTATION CONFIGURATION FOR NEW GALILEO MANAGED VPN SITES WINDOWS 98 GENERAL NETWORK CONFIGURATION Ask the customer which workstation the primary Scriptwriter person in the office will use. That person

More information

Communication to End Device Going In and Out of Slow Poll Mode

Communication to End Device Going In and Out of Slow Poll Mode Tech Note 693 Using DASMBTCP to Solve Third-Party Modbus Device Communication Problems All Tech Notes, Tech Alerts and KBCD documents and software are provided "as is" without warranty of any kind. See

More information

Prestige 623R-T. Quick Start Guide. ADSL Dual-link Router. Version 3.40

Prestige 623R-T. Quick Start Guide. ADSL Dual-link Router. Version 3.40 Prestige 623R-T ADSL Dual-link Router Quick Start Guide Version 3.40 February 2004 Introducing the Prestige The Prestige 623R-T ADSL Dual-link Router is the ideal all-in-one device for small networks connecting

More information

Pulsar 320 TCP/IP Setup Instructions

Pulsar 320 TCP/IP Setup Instructions Pulsar 320 TCP/IP Setup Instructions Contents: 1.0 Configure network settings for the PC - Connect through a network or router - Direct connect with a single PC connection 2.0 Connection to the Pulsar

More information

How to Restore a Windows System to Bare Metal

How to Restore a Windows System to Bare Metal How to Restore a Windows System to Bare Metal This article applies to Barracuda Backup Server firmware version 5.4 and higher. Bare metal recovery allows you to restore a complete Microsoft Windows system,

More information

Network Administrator

Network Administrator Network Administrator Estimating, Repair, Shop Management and Parts Catalogs User s Guide ShopKey Poway, California 2002 Copyright 2002 SnapOn Diagnostics and Mitchell Repair Information Company, LLC All

More information

Tech Note 563 Configuring FSGateway to Access Historian Data from Wonderware Application Server

Tech Note 563 Configuring FSGateway to Access Historian Data from Wonderware Application Server Tech Note 563 Configuring FSGateway to Access Historian Data from Wonderware Application Server All Tech Notes, Tech Alerts and KBCD documents and software are provided "as is" without warranty of any

More information

Tech Note 400 Configuring Remote Connections for Windows 2000/2003/XP

Tech Note 400 Configuring Remote Connections for Windows 2000/2003/XP Tech Note 400 Configuring Remote Connections for Windows 2000/2003/XP All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

More information

EDGE FX Network configuration

EDGE FX Network configuration Page 1 of 16 TITLE: Category: EDGE FX Network configuration GERBER EDGE Document Number: 4280 Supplied by: Gerber Service Last Modified: April 14, 2011 Summary: In order to connect an EDGE FX to your PC

More information

AcqKnowledge 3.7.3 or better for Windows OS (version compatibility varies each release)

AcqKnowledge 3.7.3 or better for Windows OS (version compatibility varies each release) APPLICATION NOTES 42 Aero Camino, Goleta, CA 93117 Tel (805) 685-0066 Fax (805) 685-0067 info@biopac.com www.biopac.com 09.10.2007 Application Note 209: AcqKnowledge for Windows: Upgrade for 1+MP150s and

More information

Internet Guide. Prepared for 55 John Street

Internet Guide. Prepared for 55 John Street Internet Guide Prepared for 55 John Street I. Internet Service How do I connect to the Internet? WiFi (Wireless Connectivity) is available throughout the building. In order to connect, you will need a

More information

Omni 56K USB Lite Quick Start Guide

Omni 56K USB Lite Quick Start Guide Omni 56K USB Lite Quick Start Guide ZyXEL TOTAL INTERNET ACCESS SOLUTION 1. Hardware Installation Connect your modem to your analog phone or fax. Use the phone cord included to connect to the phone jack

More information

Appendix C Preparing Your Network

Appendix C Preparing Your Network Appendix C Preparing Your Network This appendix describes how to prepare your network to connect to the Internet through the FVX538 ProSafe VPN Firewall 200 and how to verify the readiness of broadband

More information

Configuring Windows 7 64 bit for AutoVISION

Configuring Windows 7 64 bit for AutoVISION This document will describe how to configure a 64 bit version of Windows 7 Professional, Ultimate or Enterprise to utilize the Windows XP Mode (Virtual PC) capabilities to allow AutoVISION to be used in

More information

Wireless LAN 802.11g USB Adapter

Wireless LAN 802.11g USB Adapter Wireless LAN 802.11g USB Adapter User s Guide Version 1.0 User s Guide 0 Copyright statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by

More information

Tech Note 338 How to Change the ActiveFactory Reporting Website Default Install Location

Tech Note 338 How to Change the ActiveFactory Reporting Website Default Install Location Tech Note 338 How to Change the ActiveFactory Reporting Website Default Install Location All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms

More information

Configuring the IP address of the ETHER IO24 TCP RANGE

Configuring the IP address of the ETHER IO24 TCP RANGE 1 Configuring the IP address of the ETHER IO24 TCP RANGE There are a number of ways that you can configure the fixed IP Address of the Ether IO24 TCP Range. The two different methods are outlined below

More information

Network Administrator. Manager and ManagerPlus Shop Management

Network Administrator. Manager and ManagerPlus Shop Management Network Administrator Manager and ManagerPlus Shop Management Poway, California January 2005 Copyright 2003 Mitchell Repair Information Company, LLC All Rights Reserved DISCLAIMER OF WARRANTIES: Although

More information

1. Hardware Installation

1. Hardware Installation 4 Port 10/100M Internet Broadband Router with USB Printer server Quick Installation Guide #4824904AXZZ0 1. Hardware Installation A. System Requirement Before you getting started, make sure that you meet

More information

Easy Setup Guide for the Sony Network Camera

Easy Setup Guide for the Sony Network Camera -878-191-11 (1) Easy Setup Guide for the Sony Network Camera For setup, a computer running the Microsoft Windows Operating System is required. For monitoring camera images, Microsoft Internet Explorer

More information

Introduction. Versions Used Windows Server 2003

Introduction. Versions Used Windows Server 2003 Training Installing Active Directory Introduction As SonicWALL s products and firmware keeps getting more features that are based on integration with Active Directory, e.g., Active Directory Connector

More information

LPR for Windows 95/98/Me/2000/XP TCP/IP Printing User s Guide. Rev. 03 (November, 2001)

LPR for Windows 95/98/Me/2000/XP TCP/IP Printing User s Guide. Rev. 03 (November, 2001) LPR for Windows 95/98/Me/2000/XP TCP/IP Printing User s Guide Rev. 03 (November, 2001) Copyright Statement Trademarks Copyright 1997 No part of this publication may be reproduced in any form or by any

More information

Operating Instructions

Operating Instructions Operating Instructions (For Setting Up) Digital Imaging Systems Installation Overview Model No. DP-8060 / 8045 / 8035 Table of Contents Setting Your Machine Installation Overview General Installation Overview...

More information

Installing the KX-P8420 or KX-PS8100 on Windows NT 4.0.

Installing the KX-P8420 or KX-PS8100 on Windows NT 4.0. Installing the KX-P8420 or KX-PS8100 on Windows NT 4.0. Overview The KX-P8420 and KX-PS8100 can be set up using 2 methods. METHOD 1 The printer can be installed on the NT server and setup as a shared device.

More information

This tech note will explain how to use the following parameters in Configurator General Parameters.

This tech note will explain how to use the following parameters in Configurator General Parameters. Tech Note 707 Configuring Allowable Deviation in Operations and Performance All Tech Notes, Tech Alerts and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms

More information

Tech Note 637 Enabling CBM Solution 2.0 for Hierarchical EAM/CMMS System Browsing

Tech Note 637 Enabling CBM Solution 2.0 for Hierarchical EAM/CMMS System Browsing Tech Note 637 Enabling CBM Solution 2.0 for Hierarchical EAM/CMMS System Browsing All Tech Notes, Tech Alerts and KBCD documents and software are provided "as is" without warranty of any kind. See the

More information

Ethernet Interface Manual Thermal / Label Printer. Rev. 1.01 Metapace T-1. Metapace T-2 Metapace L-1 Metapace L-2

Ethernet Interface Manual Thermal / Label Printer. Rev. 1.01 Metapace T-1. Metapace T-2 Metapace L-1 Metapace L-2 Ethernet Interface Manual Thermal / Label Printer Rev. 1.01 Metapace T-1 Metapace T-2 Metapace L-1 Metapace L-2 Table of contents 1. Interface setting Guiding...3 2. Manual Information...4 3. Interface

More information

LOAD BALANCING 2X APPLICATIONSERVER XG SECURE CLIENT GATEWAYS THROUGH MICROSOFT NETWORK LOAD BALANCING

LOAD BALANCING 2X APPLICATIONSERVER XG SECURE CLIENT GATEWAYS THROUGH MICROSOFT NETWORK LOAD BALANCING SECURE CLIENT GATEWAYS THROUGH MICROSOFT NETWORK LOAD BALANCING Contents Introduction... 3 Network Diagram... 3 Installing NLB... 3-4 Configuring NLB... 4-8 Configuring 2X Secure Client Gateway... 9 About

More information

Use MPIO with QNAP Turbo NAS

Use MPIO with QNAP Turbo NAS Use MPIO with QNAP Turbo NAS How to connect to your QNAP Turbo NAS from Windows Server 2012 using MPIO QNAP provides you with what others cannot! In addition to the other available features on your Turbo

More information

Using a simple crossover RJ45 cable, you can directly connect your Dexter to any computer.

Using a simple crossover RJ45 cable, you can directly connect your Dexter to any computer. Dexter is a network device using the Ethernet protocol to connect and communicate with other devices on the network: Computers, routers, DHCP servers. Thus you have to setup your Dexter and your network

More information

Network Configuration Guide

Network Configuration Guide COMPLIANT MANAGER Model name: BMS-CM1280FTLE Prohibited Never connect the Compliant Manager to the Internet. We assume no responsibility for any problems resulting from connection to the Internet. Only

More information

64-Bit Compatibility with Micromeritics Applications

64-Bit Compatibility with Micromeritics Applications Tech Tip 7 64-Bit Compatibility with Micromeritics Applications Micromeritics products are designed to operate in most Microsoft Windows environments. However, more current versions of Microsoft Windows,

More information

Installing EDS III or EDS IV Network Support for Microsoft Windows 95 or 98 Part Number 110319-01 Rev. D

Installing EDS III or EDS IV Network Support for Microsoft Windows 95 or 98 Part Number 110319-01 Rev. D Installing EDS III or EDS IV Network Support for Microsoft Windows 95 or 98 Part Number 110319-01 Rev. D Melco provides three different kits to connect EDS III or EDS IV computers to an Ethernet network.

More information

Tech Note 425 Using the OPC Client Proxy Object to Connect with Matrikon s OPC Simulation

Tech Note 425 Using the OPC Client Proxy Object to Connect with Matrikon s OPC Simulation Tech Note 425 Using the OPC Client Proxy Object to Connect with Matrikon s OPC Simulation Server All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the

More information

SATO Network Interface Card Configuration Instructions

SATO Network Interface Card Configuration Instructions SATO Network Interface Card Configuration Instructions Table of Contents 1. Reset of wired/wireless interface card... 3 2. Installing the All-In-One Utility (recommended)... 4 3. Configuring wired/wireless

More information

Bell Business Backup Getting Started Guide. You do the work. We ll back it up. Automatically.

Bell Business Backup Getting Started Guide. You do the work. We ll back it up. Automatically. Bell Business Backup Getting Started Guide You do the work. We ll back it up. Automatically. Getting Started Guide Introduction...2 Minimum System Requirements...3 STEP 1: Downloading the software...4

More information

AcqKnowledge for Windows: Upgrade for 1+MP150s and Domain Network Access or Direct Communication Setup (Domain/Non-domain)

AcqKnowledge for Windows: Upgrade for 1+MP150s and Domain Network Access or Direct Communication Setup (Domain/Non-domain) APPLICATION NOTES 42 Aero Camino, Goleta, CA 93117 Tel (805) 685-0066 Fax (805) 685-0067 info@biopac.com www.biopac.com 09.10.2007 Application Note 208: AcqKnowledge for Windows: Upgrade for 1+MP150s and

More information

enervista UR Setup Software Quick Connect Instructions:

enervista UR Setup Software Quick Connect Instructions: enervista UR Setup Software Quick Connect Instructions: The user can connect to the UR relay via front serial port or rear Ethernet port using the Quick Connect feature of enervista UR Setup software.

More information

Dialing Into Dartmouth With Windows 95/98

Dialing Into Dartmouth With Windows 95/98 Dialing Into Dartmouth With Windows 95/98 Who needs this document? Any member of the Dartmouth community who wants to gain access to Dartmouth s network resources, such as electronic mail and the Internet,

More information

Technical Note #31. GE PMCS App Note 31 Page 1 of 5. RAS - Host and View Node. RAS - Host Configuration with No Network Adapter Installed:

Technical Note #31. GE PMCS App Note 31 Page 1 of 5. RAS - Host and View Node. RAS - Host Configuration with No Network Adapter Installed: GE PMCS App Note 31 Page 1 of 5 Technical Note #31 RAS - Host and View Node Subject: Configuring a Host and a View Node to communicate via modems. Applies To: PMCS 5.0 / Windows NT 3.51. For later versions

More information

Installing and Setting up Microsoft DNS Server

Installing and Setting up Microsoft DNS Server Training Installing and Setting up Microsoft DNS Server Introduction Versions Used Windows Server 2003 Setup Used i. Server Name = martini ii. Credentials: User = Administrator, Password = password iii.

More information

Tech Note 663 HMI Reports: Creating Alarm Database (WWALMDB) Reports

Tech Note 663 HMI Reports: Creating Alarm Database (WWALMDB) Reports Tech Note 663 HMI Reports: Creating Alarm Database (WWALMDB) Reports All Tech Notes, Tech Alerts and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use

More information

DP-313 Wireless Print Server

DP-313 Wireless Print Server DP-313 Wireless Print Server Quick Installation Guide TCP/IP Printing (LPR for Windows 95/98/Me/2000) Rev. 03 (August, 2001) Copyright Statement Trademarks Copyright 1997 No part of this publication may

More information

All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

All Tech Notes and KBCD documents and software are provided as is without warranty of any kind. See the Terms of Use for more information. Tech Note 214 Finding Memory Leaks in Windows 2000 All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information. Topic#: 000933

More information

UBIQUITI BRIDGE CONFIGURATION PROCEDURE (PowerStation & NanoStation Units ONLY)

UBIQUITI BRIDGE CONFIGURATION PROCEDURE (PowerStation & NanoStation Units ONLY) UBIQUITI BRIDGE CONFIGURATION PROCEDURE (PowerStation & NanoStation Units ONLY) Hardware Installation 1. Initial placement for programming and configuration purposes should be performed in an indoor environment.

More information

Barak & Caldera Network Setup

Barak & Caldera Network Setup Barak & Caldera Network Setup Application Note 10100112 Rev. A February 2008 Prepared by the Application Department 10100112A Matan Digital Printers Ltd. Page 1 of 17 Safety Procedures Before reading this

More information

Software Installation Guide

Software Installation Guide Software Installation Guide This manual explains how to install the software over a USB or network connection. Network connection is not available for models SP 200/200S/203S/203SF/204SF. To manually configure

More information

Configuring Cisco Network Registrar to Provide DHCP Service to Avaya IP Telephones and Avaya IP Softphones - Issue 1.0

Configuring Cisco Network Registrar to Provide DHCP Service to Avaya IP Telephones and Avaya IP Softphones - Issue 1.0 Configuring Cisco Network Registrar to Provide DHCP Service to Avaya IP Telephones and Avaya IP Softphones - Issue 1.0 Abstract These Application Notes present a sample configuration of the Cisco Network

More information

a) Network connection problems (check these for existing installations)

a) Network connection problems (check these for existing installations) How do I resolve issues with a Client not connecting to the Best Practice server instance? This FAQ is intended to answer common questions about resolving issues with a Best Practice client not connecting

More information

8/22/13 Configuring the SST5136SD PCI Card Using the New SSTDHP IO Server V8.1 or the DASDHPlus Server

8/22/13 Configuring the SST5136SD PCI Card Using the New SSTDHP IO Server V8.1 or the DASDHPlus Server Tech Note 448 Configuring the SST5136SD PCI Card Using the New SSTDHP I/O Server or the DASDHPlus Server All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind.

More information

8/23/13 Configuring SIDirect DAServer to Communicate with S7 PLC Over TCP Connection

8/23/13 Configuring SIDirect DAServer to Communicate with S7 PLC Over TCP Connection Tech Note 332 Configuring SIDirect DAServer to Communicate with S7 PLC Over TCP Connection This document and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

More information

Network Connection Quick Setup Guide

Network Connection Quick Setup Guide Xerox WorkCentre M118/M118i Network Connection Quick Setup Guide 701P42575 This guide includes instructions for: Navigating Display Screens on page 2 Network Setup Using DHCP on page 2 Network Setup Using

More information

Installing An ActiveX Control in InTouch

Installing An ActiveX Control in InTouch Tech Note 117 Using the InTouch 7.0 ActiveX Container All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information. Topic#:

More information

Locate the My Computer icon, found either on the Start menu or the desktop

Locate the My Computer icon, found either on the Start menu or the desktop 1. How to check if a network card is installed Locate the My Computer icon, found either on the Start menu or the desktop Right click on the My Computer icon and select Properties from the grey box that

More information

Apple Mac. AT&T DSL Internet Service Implementation Planner Apple Mac PC Configuration Guide Version 1.2 Page 1

Apple Mac. AT&T DSL Internet Service Implementation Planner Apple Mac PC Configuration Guide Version 1.2 Page 1 Apple Mac Page 1 Apple Mac Setup Welcome to AT&T DSL Internet Service! This guide is designed to help you configure your Mac to access the Internet quickly and easily using AT&T DSL. Before You Begin First,

More information

All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information.

All Tech Notes and KBCD documents and software are provided as is without warranty of any kind. See the Terms of Use for more information. Tech Note 89 Performing DDE Operations with Visual Basic All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information. Topic#:

More information

Install MS SQL Server 2012 Express Edition

Install MS SQL Server 2012 Express Edition Install MS SQL Server 2012 Express Edition Sohodox now works with SQL Server Express Edition. Earlier versions of Sohodox created and used a MS Access based database for storing indexing data and other

More information

Configuring TCP/IP Networking for Windows XP:

Configuring TCP/IP Networking for Windows XP: Configuring TCP/IP Networking for Windows XP: Configuration setup - Point to and click on Start (the pop up Start Menu appears) Next point to and click on Control Panel (the Control Panel window appears).

More information

MODEM AND DIAL-UP. Installation/Configuration (Windows 95/98/Me/NT/2000/XP)

MODEM AND DIAL-UP. Installation/Configuration (Windows 95/98/Me/NT/2000/XP) MODEM AND DIAL-UP Installation/Configuration (Windows 95/98/Me/NT/2000/XP) Iridium Satellite LLC 1 February 22, 2006 --------------------------------------------------------------------------------------------------------------------------------------------TABLE

More information

Application Note Configuring the UGate 3000 for use with ClipMail Pro and ClipExpress

Application Note Configuring the UGate 3000 for use with ClipMail Pro and ClipExpress Application Note Configuring the UGate 3000 for use with Introduction This Application Note guides the ClipMail user through the UGate gateway configuration process by using a simple dial up connection

More information

Oven Software Installation for Windows XP (HC1 or HC2 controller) (Software version 4.0.x.x)

Oven Software Installation for Windows XP (HC1 or HC2 controller) (Software version 4.0.x.x) Basic System requirement: OS: Windows XP (Home or Professional) Processor speed: preferred 2GHz or more RAM: 256MB minimum Communication using: For HC1-x controller: Serial Com port-1 (built-in to computer

More information

[Setup procedure for Windows 95/98/Me]

[Setup procedure for Windows 95/98/Me] [Setup procedure for Windows 95/98/Me] a. One Print Server. b. One external AC power adapter. c. One setup CD. (For Windows 95/98/Me/NT/2000/XP). d. One user s manual (included quick guide). a. Turn off

More information