QUANTUM Roller Blind Hardware System

Transcription

1 QUANTUM Roller Blind Hardware System

2

3 Introduction and Overview QUANTUM Roller Blind Hardware System Introducing Hunter Douglas Commercial QUANTUM, the roller blind hardware system developed by an international design team specifically for our requirements. Featuring a sleek architectural design with smooth operation and unrivalled inner strength, QUANTUM Roller Blind Hardware System allows you to span even the largest window beautifully. Highly durable hardware delivers smooth and reliable operation. 3

4 Features and Smooth and Light Operation Can be operated using either standard chain drive or motorised technology. The durable standard chain drive is available in two ratio mechanism 1:1 and 1:1.75. The standard 1:1.75 ratio enables a heavier blind to be lifted without the need of a spring booster. But you can nominate to use the optional 1:1 ratio. It is also aesthetically pleasing in one size format for a consistent look throughout the home. Universal spring loaded idle ends provide for smooth and easy installation. The aluminium tube has been engineered to perform well with minimal deflection over large expanses. 4 STRENGTH

5 Features and Living with Innovation Two compact dual bracket designs are available: - The standard (under) roll configuration ensures the blind skin can be fitted close to the window. - The reverse (over) roll configuration provides a self pelmet effect. Both dual brackets can be installed with either same side or opposite end controls and have universal mounting options. An optional patented integrated levelling device makes it easy to adjust shades after mounting. Two standard linking systems are available: - The standard connector set minimises the intermediate gap on linked configurations. - The optional aligner link maximises flexibility during installation with a fine adjustment option for aligning the level of blinds. Both linking options have 15 degree play. This provides an allowance for slightly misaligned installations. An independent linking option is available for configurations that require multiple operation. A 45 and 90 degree linking mechanism is also available for bay and corner windows. A sleek (84mm projection) and contemporary head box and fascia system are available in both an anodised and powder coated finish (White, Black or Magnolia) with colour coded endcaps. Both the head box and fascia system can be installed in both reveal and face fit positions and have a snap lock cover and plastic outlets for easy installation and quiet operation. To obtain room darkening, the head box system can be installed with side channels, available in matching powder coated colours (White, Black or Magnolia) or anodised finish. Standard Dual Roller Linked Blinds INNOVATIVE Headbox System 5

6 Features and Outer Beauty Hardware components are available in four colour options White, Black, Grey and Magnolia. All brackets are universal in design which means the operating side can be changed simply on site if required. Two bracket sizes are available, 38mm and 55mm which ensures the correct bracket can be selected for challenging installations and maximises the drop capacity. Brackets are available with slim line end caps which are recommended for all face fit installations. All QUANTUM Roller Blind Hardware Systems, are available with the Ellipse Balance Rail which features a sound proofing bumper and has been designed with perfect weight distribution in mind to ensure your fabrics hang very flat. 6 BEAUTYY

7

8 Quantum Standard Roller System Components and Dimensions NO CODE DESCRIPTION Components HD 37mm Tube Not Shown mm Tube mm Tube XXXX 37mm Tube Adapter XXXXA 50mm Tube Adapter XXXX 31mm Tube Plug XXXX Idle End XXXX Chain Drive 1:1 Not Shown XXXX Chain Drive 1.75:1 The QUANTUM Roller Blind Hardware System, can be operated with either a chain drive or motor. Each chain operated blind will be supplied with a plastic chain loop however metal or stainless steel chains are available on request. An Ellipse Rail comes standard on all blinds and is available in either anodised finish or you can choose from a selection of popular powder coated colours (White, Black or Birch White). Not Shown XXXX 37mm Spring Not Shown XXXX 50mm Spring XXXX Bracket 38mm Not Shown XXXX Bracket 55mm XXXX Bracket Cover 38mm Not Shown XXXX Bracket Cover 55mm XXXX Chain Drive Cover Plate XXXXA Levelling Bracket 38mm A Integrated Leveller Not Shown A Integrated Leveller Key 8

9 Quantum Standard Roller System Components and Dimensions Blind Width Cloth Width 38mm Bracket Dimensions 75mm 68mm 55mm Bracket Dimensions 75mm 86mm NOTE: Allow an extra 2mm for each end cap. 18mm 12mm Limitations Minimum width single blind Minimum width single blind with booster spring Minimum width single motorised blind (switch) Minimum width single motorised blind (RTS) Maximum width single blind Minimum drop single blind Maximum drop single blind 500mm 750mm 650mm 690mm Please refer to the pricing guide as this is fabric dependent. 300mm Please refer to the pricing guide as this is fabric dependent. 9

10 Quantum Linked Roller System Components and Dimensions Components NO CODE DESCRIPTION Linked Rollers are available with either a straight connector or an aligner connector. Unless otherwise nominated the blind will always be supplied with the straight connector which ensures the light gap between the linking blinds is minimised (17mm). The optional aligner connector has been designed with special patented technology to assist when installing blinds that may be trickier to line up XXXXA Connector Set XXXXA Aligner Set XXXXA Tube Plug Connector XXXXA Idle End (Locking Ring) XXXXA Linked Bracket Cover 38mm Not Shown XXXXA Linked Bracket Cover 55mm Not Shown Not Shown A A Uni-Joint Component - 90 degree angle (Metal) Uni-Joint Component - 45 degree angle (Metal) Not Shown Independent Link Component 10

11 Quantum Linked Roller System Components and Dimensions Blind Width System Width Blind Width 38mm Bracket Dimensions Tube/Cloth Width Tube/Cloth Width 75mm 68mm 55mm Bracket Dimensions 75mm 86mm 18mm *See Below 12mm * Straight Connector = 17mm Aligner Connector = 22mm NOTE: Allow an extra 2mm deduction for each end cap. Limitations Maximum number of linked blinds 3 Note: For Bay windows there is also a 45 and 90 degree angle linking system. We recommend that the brackets for these blinds are installed before measuring the opening width for an order. 11

12 Quantum Headbox System Components and Dimensions Side Channel Dimensions mm 16.8mm 26.8mm 63.5mm 26 Components NO CODE DESCRIPTION XXXX H-Box Back Plate The contemporary headbox system has been designed to provide a simple slim line profile whilst at the same time maximising the drop capacity for your roller. The headbox is available in both anodised finish or a choice of powder coated colours (White, Black or Magnolia). In situations where you require additional light control a matching one piece side channel system is available and easy to install XXXX H-Box Front Plate XXXXA Chain Outlet Set XXXX H-Box Endcaps Square XXXX Side Channel XXXXA Side Channel Top Insert XXXXA Side Channel Bottom Set A Side Channel Fixing Set (Metal) H-Box Bracket 12

13 Quantum Headbox System Components and Dimensions Blind Width Tube/Cloth Width 84mm 89mm 21mm 15mm Limitations HEADBOX CAPACITY 37mm Tube (Blind Width < 2600) Fabric Thickness < 0.55mm 3.7m drop Fabric Thickness < 0.75mm 3.2m drop 50mm Tube (Blind Width > 2600) Fabric Thickness < 0.55mm 2.4m drop Fabric Thickness < 0.75mm 1.9m drop 13

14 Quantum Dual Roller System Components and Dimensions 29 STANDARD BRACKET OPTIONS REVERSE BRACKET OPTIONS Two Dual Bracket systems are available. The standard roll bracket has been designed to keep your blind skins as close to the window as possible, whilst the reverse roll bracket provides a self pelmet effect and is ideal for use with fabrics that have a neutral toned backing. Blinds can be installed using either same side or opposite end controls. Components NO CODE DESCRIPTION XXXX Std Roll Dual Bracket Not Shown XXXX Rev Roll Dual Bracket Note: All dual brackets are supplied with bracket covers. 14

15 Quantum Dual Roller System Components and Dimensions DUAL ROLLER DIMENSIONS Blind Width Tube Width Standard Roll Bracket 99mm 160mm Reverse Roll Bracket 92mm 155mm Note: Allow an extra 5mm deduction for each end cap. 18mm 12mm Limitations Minimum width single blind Minimum width single blind with booster spring Minimum width single motorised blind (Switch) Minimum width single motorised blind (RTS) Maximum width single blind Minimum drop single blind Maximum drop single blind Maximum drop dual bracket 500mm 750mm 650mm 690mm Please refer to the pricing guide as this is fabric dependent. 300mm Please refer to the pricing guide as this is fabric dependent. 3,000mm 15

16 Quantum Roller Blind Hardware System Limitations Operation Type Limitations (for Single Blinds and Linked Systems) WIDTH LINKED BLIND SECTION ONLY DROP Tube Chart WIDTH :1 Chain drive is optional. 1:175 chain drive will be fitted as standard. Chain drive 1:1 (3kg max) Chain drive 1:175 (4kg max) Chain drive 1:75 w/spring (4.5kg max) Motorised Only Not recommended DROP mm tube HD 37mm tube 50mm tube Not recommended NOTE: These charts have been calculated using a 400gsm fabric and bottom rail weight of 350g per metre. They are provided as a recommended guide, for further details please refer to your pricing guide. 16

17 Quantum Roller Blind Hardware System Measuring Deductions Guide To simplify the ordering process, all measuring deductions will be made automatically in the factory. All you need to do is enter the size of the opening you wish your blind to cover on the order form. The exception to this is 90 degree corners and bay windows. Corners NOTE: FOR WINDOWS IN REVEAL BRACKETS MUST BE CEILING FIXED FOR DEDUCTIONS TO WORK. BACK EDGE FRONT EDGE ON FACE Deductions are only approximate due to thickness of fabric and drop, for best results install the thru blind then measure for the butt blind. Corners in Reveal- Front Edge Through Blind Butt Blind Corners in Reveal- Back Edge Through Blind Butt Blind Corners on Face 38mm projection bracket 55mm projection Bracket Deductions +50mm(from corner) - 0mm Deductions - 0mm - 60mm (37mm Tube) - 80mm (50mm Tube) Deductions (butt blinds) - 75mm - 90mm Bays TOP FIX BACK EDGE TOP FIX FRONT EDGE ON FACE Bays in Reveal Deductions Front edge of reveal - 0mm - 0mm - 0mm Back Edge of reveal - 22mm - 44mm - 22mm Bays on Face 38mm projection Bracket 55mm projection Bracket Deductions - 28mm - 56mm - 28mm - 33mm - 66mm - 33mm Angled Linked Blinds - Bay Window FACE FIT MEASURE WALL Brackets to be fixed to wall Angled Link Bay on Face 38mm projection Bracket 55mm projection Bracket Deductions - 38mm - 76mm - 38mm - 43mm - 86mm - 43mm CEILING FIT FRONT EDGE of reveal Angled Link Bay in Reveal Front Edge of reveal Deductions - 10mm - 20mm - 10mm *gap between brackets 30mm approximate Angled Linked Blinds - 90 Corners FACE FIT Angled Link Corners on Face Measure blinds into the corner and deduct 76mm from each blind. Angled Link Corners in Reveal Measure from the front edge of reveal and deduct 10mm from each blind. CEILING FIT FRONT EDGE of REVEAL In all corner linked situations we strongly recommend that the brackets are fixed in exact location first and then measured outside edge to outside edge of the bracket to ensure the gap is minimised. *Gap between brackets 30mm approximate 17

18 Quantum Motorisation Quantum Roller Blind Hardware System is compatible with all the motorisation options you are most familiar with today. In addition, the introduction of the new HDRF quiet AC-240 volt motor range, utilising the ultra-sleek SUITE remote control in both 1 and 4 channels. QUANTUM 50 SYSTEM MOTOR REMOTE CONTROL SWITCH CONTROL ORDER CODE FEATURES SYSTEM USED BATTERY 240V SLEV (12V) HDR HunterDouglas - HDRF Superior range, modern sleek Remote Control. QUANTUM 50 SR Somfy - RTS Sonesse quiet motor. QUANTUM 50 MR Merger - Low Cost remote control solution. QUANTUM 50 HDS HunterDouglas - Quiet 4 wire motor for switch or home automation QUANTUM 50 SS Somfy -Sonesse Quiet 4 wire motor for switch or home automation QUANTUM 50 MS Merger - Low Cost 4 wire motor for switch or home automation QUANTUM 50 QUANTUM 37 SYSTEM REMOTE CONTROL SWITCH CONTROL SK1 Somfy - Wirefree battery operated. QUANTUM 37 MR37 Merger - Low Cost 12Volt Remote Control QUANTUM 37 HDS37 HunterDouglas - Premium Super Quiet motor for switch or home automation. QUANTUM 37 18

19 Quantum Motorisation Quantum Motorisation is compatible with both Hunter Douglas and Somfy premium, and Merger low cost motorisation solutions. The Introduction of the new Hunter Douglas HDRF quiet AC-240 volt motor, utilising the modern sleek Touch Sensitive remote control in both 1 and 4 channels enables simple remote control, as well as switch and automation control via the inbuilt switch connector. Quantum Roller Blind hardware options including Dual, Linked and Headbox are available with motorisation solutions. Quantum Motorisation can be operated using a Building Management Control System. HDRF Motors HDRF is the latest in wireless motor technology. The new range of M40RF motors have an integrated radio receiver for simple one plug installation. Motors can be configured and operated from the modern touch sensitive 4 Channel SUITE remote control, or operated from the motor head for quick setup and operation during installation. HDRF uses intelligent bidirectional communication between each motor and the remote control to ensure that operation is always flawless and uninterrupted. HDRF motors have the ability to simultaneously connect to automation systems or be controlled via a wall switch, all from the one integrated motor. 19

20 Fabric Collection Fabrics Collection The beautiful Fabric Collection provides you with the ultimate colours and styles from plain to textured weaves, in a range of translucencies from light filtering to block-out. Fabrics are designed to suit your light, glare, heat and privacy needs, with a range of low VOC (Volatile Organic Compound) fabrics for those sensitive to the smell of fabrics. Many fabrics are Sanitized treated - for optimal hygiene and treated with DURAGUARD Fabric Protector which effectively repels most stain causing agents. The Fabric Collection encompasses the following applications: Roller Blinds, Panel Glide, Roman Shades, Vertical Blinds and Motorisation. 20

21 Fabric Collection FABRIC OPACITY E a s y t o c l e a n & maintain Sunscreen Sunscreen fabrics allow for heat and light control whilst maintaining your view. Perfect for reducing glare and heat in a room exposed to the sun. Layer with blockout fabrics for night time privacy. Many Fabrics are treated with DURAGUARD Fabric Protector, which effectively repels most stain causing agents with its proven, water based, preventative formula. Your Window Fashions will Resist water stains from rain, moisture and condensation on windows Resist oily stains from spills or fingerprints Sheer Sheer fabrics give daytime privacy and some filtered view-through subject to the texture and weave. Layer with blockout fabrics to give night time privacy. F or freshness & wellbeing in your home Translucent Translucent fabrics screen out harsh light, but do not allow a view-through. They bring texture or patterns to light coming into a room whilst providing daytime and night time privacy. Many Fabrics are treated with Sanitized hygiene function, which Keeps odours away ensuring freshness in your home Stops mildew and fungi growing on your window coverings keeping your home clean Protects against the development of bacteria ensuring well-being in your home The Sanitized Antimicrobial Protection is free of harmful substances and is recommended by institutions for allergy sufferers Blockout Blockout fabrics offer the ultimate level of privacy, day and night whilst helping to insulate the room. Blockout fabrics offer room darkening capabilities. Ideal for bedrooms and home theatre / TV rooms. 21

22 Product Installation INSTALLATION - STANDARD ROLLER SYSTEM a b d c 1 click 2 1. Fix bracket with the screws provided 2. Place the chain drive in the bracket (1) 3. Slide it down until it clicks (2). click 4. Place the tube adapter on the chain drive. Press the idle end and lift the blind. 5. Snap it to the bracket. 6. Slide the end caps onto the brackets. INSTALLATION - STANDARD ROLLER SYSTEM WITH LEVELLER BRACKET 1. Make sure that the opening for the Allen key is pointing downwards before installing the brackets. Change the orientation by loosening the 2 screws and turning the leveller 90. Fix the screws. 2. To adjust skewing, put the provided Allen key into the screw of the leveller and turn it left or right to move the blind up or down. 22

23 Product Installation REMOVAL - STANDARD ROLLER SYSTEM Slide a screw driver between idle end and bracket and push the idle end in the chain drive direction. Slide the end cap towards you. 2. Move the blind downwards out of the bracket. 3. Push the pin of the chain drive and take the chain drive out of the bracket. 4. Place a screw driver under the pin of the chain drive and pull it outwards. Take the chain drive out of the bracket. 23

24 Product Installation INSTALLATION - LINKED BLINDS 1. Place the tube adaptor on the chain drive head. Press the idle end and lift the blind. 2. Fix the outer bracket with the screws provided. 3. Slide the aligner or the connector through the bracket into the idle end click 3 4. Place the tube adaptor on the aligner or connector head. 5. Press the spring loaded idle with locking ring end and lift the blind and snap it to the bracket. 6. To align the bottom rails, push the blind against the idle end (1), turn the blind, level the bottom rail with the other one (2). Release to fix the position (3). NOTE: This is not possible when using the standard connector set. 7. Fix the blind by turning the locking ring against the idle end. 8. Slide the end caps onto the brackets. NOTE: The aligner component has an extra metal bearing ring which is only required if the centre space between two blinds is being extended. For normal installation this can be removed using an allen key. 24

25 Product Installation REMOVAL - LINKED BLINDS 1. Slide the end cap towards you. 2. Unfasten the locking ring. Slide a screw driver between locking ring and bracket and push the idle end in the aligner direction. 3. Move the blind downwards out of the bracket. Pull the aligner or connector out of the idle end. QUANTUM INSTALLATION INSTALLATION - SPRING BOOSTER 1 click Place the idle end into the bracket. Push blind in the idle end direction (1) and lift blind up (2). 2. Lift the blind up until chain drive clicks in place (3). 3. Fix the blind by turning the locking ring against the idle end. QUANTUM INSTALLATION REMOVAL - SPRING BOOSTER Unfasten the locking ring. 2. Slide up the chain drive. 3. Push blind in the idle end direction (2) and lower blind to remove from bracket (3). 25

26 Product Installation INSTALLATION - UNI JOINT BLINDS 1. Install the main blind with the linked end cap. 2. Slide the 45º - 90º joint through the bracket into the idle end. 3. Place the inner bracket with the linked end cap horizontally to the bracket of the main blind and fix it with the screws provided. X 4. The maximum distance between bracket and cardan joint is X = 40 mm. 5. Fix the outer bracket with the screws provided. 6. Slide the idle end onto the hexagon of the 45º - 90º joint. NOTE: Level the bottom rail with the other before installation. > Fix the blind by turning the locking ring (on both sides) against the idle end. Slide the end cap onto the bracket Loosen the screw from the stopper (90º joint). The angle between the hexagon and the cardan should not exceed 45º. The axes of the blinds should cross in the middle of the cardan. Fix both stoppers when using 90º joint.

27 Product Installation INSTALLATION - HEADBOX SYSTEM 1. Fix headbox back plate to wall by drilling through extrusion and slide brackets into keyway. Tighten grubscrew. 2. Slide end caps into the headbox back plate. 3. Clip headbox front plate inside keyway at the top of the back plate. NOTE: End cap removed for demonstration only. 4. Clip headbox front plate into place to secure the endcaps. INSTALLATION - FASCIA SYSTEM 1. Fix fascia brackets to wall by drilling through extrusion and slide blind brackets into keyway. 2. Slide end caps into the fascia brackets. 3. Clip fascia plate inside keyway at the top of the fascia brackets. NOTE: End cap removed for demonstration only. 4. Clip fascia plate into place to secure the endcaps. 27

28 Product Installation INSTALLATION - SIDE CHANNELS X X = max mm 1. Level the side guiding channel flush with the headbox end cap. Mark this position. 2. Fix the top clip with a distance max 7.5mm from the bottom of the headbox end cap. 3. Fix the lower clip - and clips at 1000 mm intervals - before installing the channel. Tab click 4. Place the bottom rail into the side guiding channel. Snap and remove tab on chain drive end. 5. Snap channel into clips. 28

29

30 5YEAR WARRANTY * *Refer to for warranty document.

31 Sanitized and the Sanitized symbol are trademarks of SANITIZED AG, Switzerland, registered in numerous countries. Copyright 2013 Hunter Douglas Limited [ABN ] Registered Trade Marks of Hunter Douglas Limited Somfy is a registered trade mark of SOMFY Pty Limited 03/2013

32