IR Receiver Modules for Remote Control Systems

Size: px
Start display at page:

Download "IR Receiver Modules for Remote Control Systems"

Transcription

1 TSOP39.., TSOP393.. IR Receiver Modules for MECHANICAL DATA Pinning: = OUT, 2 = V S, 3 = GND 926 FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Insensitive to supply voltage ripple and noise Component in accordance to RoHS 22/95/EC and WEEE 22/96/EC DESCRIPTION The TSOP39.., TSOP393.. series are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor. The TSOP39.. is compatible with all common IR remote control data formats. The TSOP393.. is optimized to better suppress spurious pulses from energy saving fluorescent lamps but will also suppress some data signals. This component has not been qualified according to automotive specifications. PARTS TABLE CARRIER FREQUENCY SHORT BURST AND HIGH DATA RATES (AGC) NOISY ENVIRONMENTS AND SHORT BURTS (AGC3) 3 khz TSOP393 TSOP khz TSOP3933 TSOP khz TSOP3936 TSOP khz TSOP3938 TSOP khz TSOP394 TSOP khz TSOP3956 TSOP39356 BLOCK DIAGRAM APPLICATION CIRCUIT 6835 Input AGC Band pass Demodulator 3 kω 2 V S OUT 77_5 Transmitter with TSALxxxx IR receiver Circuit V S OUT GND R C V O µc + V S GND PIN Control circuit 3 GND R and C are recommended for protection against EOS. Components should be in the range of 33 Ω < R < kω, C >. µf. Document Number: Rev..3, 29-Jan-9

2 IR Receiver Modules for TSOP39.., TSOP393.. ABSOLUTE MAXIMUM RATINGS () PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage (pin 2) V S -.3 to + 6. V Supply current (pin 2) I S 3 ma Output voltage (pin ) V O -.3 to (V S +.3) V Output current (pin ) I O 5 ma Junction temperature T j C Storage temperature range T stg - 25 to + 85 C Operating temperature range T amb - 25 to + 85 C Power consumption T amb 85 C P tot mw Soldering temperature t s, mm from case T sd 26 C Note () Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating condtions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS () PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E v =, V S = 3.3 V I SD ma Supply current (pin 2) E v = 4 klx, sunlight I SH.45 ma Supply voltage V S V Transmission distance Output voltage low (pin ) Minimum irradiance Maximum irradiance Note () T amb = 25 C, unless otherwise specified TYPICAL CHARACTERISTICS T amb = 25 C, unless otherwise specified E v =, test signal see fig., IR diode TSAL62, I F = 25 ma I OSL =.5 ma, =.7 mw/m 2, test signal see fig. Pulse width tolerance: t pi - 5/f o < t po < t pi + 6/f o, test signal see fig. t pi - 5/f o < t po < t pi + 6/f o, test signal see fig. d 45 m V OSL mv min mw/m 2 max. 3 W/m 2 Directivity Angle of half transmission distance ϕ /2 ± 45 deg V O V OH Optical Test Signal (IR diode TSAL62, I F =.4 A, N = 6 pulses, f = f, t = ms) t pi *) V OL t ) t 2) t d po T *) t pi 6/fo is recommended for optimal function Output Signal ) 3/f < t d < 9/f 2) t pi - 4/f < t po < t pi + 6/f Fig. - Output Active Low t 4337 t po - Output Pulse Width (ms) λ = 95 nm, optical test signal, fig Output Pulse Width Input Burst Length - Irradiance (mw/m²) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Document Number: 8762 Rev..3, 29-Jan-9 53

3 TSOP39.., TSOP393.. IR Receiver Modules for V O V OH V OL Optical Test Signal 6 µs 6 µs t = 6 ms Output Signal, (see fig. 4) t on t off t t min. - Threshold Irradiance (mw/m²) Correlation with Ambient Light Sources: W/m² =.4 klx (Std. illum. A, T = 2855 K) W/m² = 8.2 klx (Daylight, T = 59 K) Wavelength of Ambient Illumination: λ = 95 nm.. - Ambient DC Irradiance (W/m²) Fig. 3 - Output Function Fig. 6 - Sensitivity in Bright Ambient T on, T off - Output Pulse Width (ms) λ = 95 nm, Optical Test Signal, Fig Irradiance (mw/m²) T on T off Fig. 4 - Output Pulse Diagram f = Hz.9.8 f = khz.7.6 f = 2 khz.5.4 f = 3 khz.3.2 f = f o Vs RMS - AC Voltage on DC Supply Voltage (mv) min. - Threshold Irradiance (mw/m²) Fig. 7 - Sensitivity vs. Supply Voltage Disturbances min. / - Rel. Responsivity f = f ± 5 % Δ f(3 db) = f / f/f - Relative Frequency Fig. 5 - Frequency Dependence of Responsivity E - Max. Field Strength (V/m) f - EMI Frequency (MHz) Fig. 8 - Sensitivity vs. Electric Field Disturbances Document Number: Rev..3, 29-Jan-9

4 IR Receiver Modules for TSOP39.., TSOP Max. Envelope Duty Cycle TSOP TSOP f = 38 khz, = 2 mw/m² Burst Length (number of cycles/burst) d rel - Relative Transmission Distance Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length Fig. 2 - Horizontal Directivity min. - Threshold Irradiance (mw/m²) T amb - Ambient Temperature ( C) d rel - Relative Transmission Distance Fig. - Sensitivity vs. Ambient Temperature Fig. 3 - Vertical Directivity S ( ) rel - Relative Spectral Sensitivity Wavelength (nm) 5 Fig. - Relative Spectral Sensitivity vs. Wavelength min. - Sensitivity (mw/m²) V S - Supply Voltage (V) Fig. 4 - Sensitivity vs. Supply Voltage Document Number: 8762 Rev..3, 29-Jan-9 55

5 TSOP39.., TSOP393.. IR Receiver Modules for SUITABLE DATA FORMAT The TSOP39.., TSOP393.. series are designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 khz) and fulfill the conditions in the table below. When a data signal is applied to the TSOP39.., TSOP393.. in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are: DC light (e.g. from tungsten bulb or sunlight) Continuous signals at any frequency Modulated noise from fluorescent lamps with electronic ballasts (see figure 5 or figure 6) IR Signal 692 IR Signal from Fluorescent Lamp with Low Modulation Time (ms) Fig. 5 - IR Signal from Fluorescent Lamp with Low Modulation IR Signal from Fluorescent Lamp with High Modulation IR Signal Time (ms) Fig. 6 - IR Signal from Fluorescent Lamp with High Modulation TSOP39.. TSOP393.. Minimum burst length 6 cycles/burst 6 cycles/burst After each burst of length a minimum gap time is required of For bursts greater than a minimum gap time in the data stream is needed of 6 to 7 cycles cycles 7 cycles >.2 x burst length Note For data formats with long bursts (more than carrier cycles) please see the data sheet for TSOP392.., TSOP to 35 cycles cycles 35 cycles > 6 x burst length Maximum number of continuous short bursts/second 2 2 Recommended for NEC code yes yes Recommended for RC5/RC6 code yes yes Recommended for Sony code yes no Recommended for RCMM code yes yes Recommended for r-step code yes yes Recommended for XMP code yes yes Suppression of interference from fluorescent lamps Common disturbance signals are supressed (example: signal pattern of fig. 5) Even critical disturbance signals are suppressed (examples: signal pattern of fig. 5 and fig. 6) Document Number: Rev..3, 29-Jan-9

6 IR Receiver Modules for TSOP39.., TSOP393.. PACKAGE DIMENSIONS in millimeters 9 Document Number: 8762 Rev..3, 29-Jan-9 57

7 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 9 Revision: 8-Jul-8

IR Receiver Modules for Remote Control Systems

IR Receiver Modules for Remote Control Systems IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved

More information

Photo Modules for PCM Remote Control Systems

Photo Modules for PCM Remote Control Systems Photo Modules for PCM Remote Control Systems Available types for different carrier frequencies Type fo Type fo TSOP183 3 khz TSOP1833 33 khz TSOP1836 36 khz TSOP1837 36.7 khz TSOP1838 38 khz TSOP184 4

More information

IR Receiver Modules for Remote Control Systems

IR Receiver Modules for Remote Control Systems IR Receiver Modules for Remote Control Systems 1 2 MECHNICAL DATA Pinning for TSOP44.., TSOP48..: 1 = OUT, 2 = GND, 3 = V S Pinning for TSOP22.., TSOP24..: 1 = OUT, 2 = V S, 3 = GND 3 16672 FEATURES Improved

More information

IR Receiver Modules for Remote Control Systems

IR Receiver Modules for Remote Control Systems IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved

More information

IR Receiver Module for Light Barrier Systems

IR Receiver Module for Light Barrier Systems Not for New Design - Alternative Available: New TSSP4038 (#82458) www.vishay.com IR Receiver Module for Light Barrier Systems TSOP4038 2 3 MECHANICAL DATA Pinning: = OUT, 2 = GND., 3 = V S 6672 FEATURES

More information

IR Sensor Module for Reflective Sensor, Light Barrier, and Fast Proximity Applications

IR Sensor Module for Reflective Sensor, Light Barrier, and Fast Proximity Applications IR Sensor Module for Reflective Sensor, Light Barrier, and Fast Proximity Applications MECHANICAL DATA Pinning: = OUT, 2 = GND, 3 = V S 2 3 6672 APPLICATIONS Reflective sensors for hand dryers, towel or

More information

IR Receiver Modules for Remote Control Systems

IR Receiver Modules for Remote Control Systems IR Receiver Modules for Remote Control Systems Description The - series are miniaturized SMD-IR Receiver Modules for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame,

More information

Silicon PIN Photodiode

Silicon PIN Photodiode Silicon PIN Photodiode DESCRIPTION 94 8583 BPW34 is a PIN photodiode with high speed and high radiant sensitivity in miniature, flat, top view, clear plastic package. It is sensitive to visible and near

More information

Preamplifier Circuit for IR Remote Control

Preamplifier Circuit for IR Remote Control Preamplifier Circuit for IR Remote Control DESCRIPTION 2296 The is designed for use in an IR receiver application together with a photo pin diode. It is a sophisticated receiver concept that is very sensitive

More information

High Power Infrared Emitting Diode, 940 nm, GaAlAs/GaAs

High Power Infrared Emitting Diode, 940 nm, GaAlAs/GaAs TSAL64 High Power Infrared Emitting Diode, 94 nm, GaAlAs/GaAs DESCRIPTION 94 8389 TSAL64 is an infrared, 94 nm emitting diode in GaAlAs/GaAs technology with high radiant power molded in a blue-gray plastic

More information

Silicon PIN Photodiode

Silicon PIN Photodiode Silicon PIN Photodiode DESCRIPTION 94 8632 is a PIN photodiode with high speed and high radiant sensitivity in a clear, side view plastic package. It is sensitive to visible and near infrared radiation.

More information

Preamplifier Circuit for IR Remote Control

Preamplifier Circuit for IR Remote Control Product is End of Life June-216 and Replaced by New (#82748) Preamplifier Circuit for IR Remote Control (please see PCN OMV-877-215, datasheet is valid until 3 th June 216) MECHANICAL DATA Pinning: 1,

More information

Silicon PIN Photodiode

Silicon PIN Photodiode VEMD940F Silicon PIN Photodiode DESCRIPTION VEMD940F is a high speed and high sensitive PIN photodiode in a miniature side looking, surface mount package (SMD) with daylight blocking filter. Filter is

More information

Preamplifier Circuit for IR Remote Control

Preamplifier Circuit for IR Remote Control Preamplifier Circuit for IR Remote Control 22906 FEATURES Carrier-out-function: carrier frequency and burst length accurately correspond to the input signal AC coupled response from 20 khz to 60 khz; all

More information

High Power Infrared Emitting Diode, 940 nm, GaAlAs/GaAs

High Power Infrared Emitting Diode, 940 nm, GaAlAs/GaAs TSAL51 High Power Infrared Emitting Diode, 94 nm, GaAlAs/GaAs DESCRIPTION 96 1155 TSAL51 is an infrared, 94 nm emitting diode in GaAlAs/GaAs technology with high radiant power, molded in a blue-gray plastic

More information

Reflective Optical Sensor with Transistor Output

Reflective Optical Sensor with Transistor Output TCRT5000, TCRT5000L Reflective Optical Sensor with Transistor Output FEATURES Package type: leaded Detector type: phototransistor Dimensions (L x W x H in mm): 10.2 x 5.8 x 7 Peak operating distance: 2.5

More information

Silicon NPN Phototransistor

Silicon NPN Phototransistor Silicon NPN Phototransistor DESCRIPTION 7 is a silicon NPN phototransistor with high radiant sensitivity in black, T-1¾ plastic package with base terminal and daylight blocking filter. Filter bandwidth

More information

Reflective Optical Sensor with Transistor Output

Reflective Optical Sensor with Transistor Output www.vishay.com TCRT, TCRT Reflective Optical Sensor with Transistor Output 2836 TCRT A C E C TCRT 955_ FEATURES Package type: leaded Detector type: phototransistor Dimensions (L x W x H in mm): 7 x 4 x

More information

High Power Infrared Emitting Diode, 940 nm, GaAlAs, MQW

High Power Infrared Emitting Diode, 940 nm, GaAlAs, MQW High Power Infrared Emitting Diode, 94 nm, GaAlAs, MQW DESCRIPTION 94 8389 is an infrared, 94 nm emitting diode in GaAlAs multi quantum well (MQW) technology with high radiant power and high speed molded

More information

High Speed Infrared Emitting Diode, 870 nm, GaAlAs Double Hetero

High Speed Infrared Emitting Diode, 870 nm, GaAlAs Double Hetero TSFF55 High Speed Infrared Emitting Diode, 87 nm, GaAlAs Double Hetero 26 DESCRIPTION TSFF55 is an infrared, 87 nm emitting diode in GaAlAs double hetero (DH) technology with high radiant power and high

More information

Ultrabright White LED, Ø 3 mm

Ultrabright White LED, Ø 3 mm Ultrabright White LED, Ø 3 mm DESCRIPTION The VLHW41 series is a clear, untinted 3 mm LED for high end applications where supreme luminous intensity is required. These lamps utilize the highly developed

More information

High Speed Infrared Emitting Diode, 940 nm, GaAlAs, MQW

High Speed Infrared Emitting Diode, 940 nm, GaAlAs, MQW High Speed Infrared Emitting Diode, 940 nm, GaAlAs, MQW DESCRIPTION is an infrared, 940 nm side looking emitting diode in GaAlAs multi quantum well (MQW) technology with high radiant power and high speed,

More information

Optocoupler, Phototransistor Output, with Base Connection

Optocoupler, Phototransistor Output, with Base Connection 4N25, 4N26, 4N27, 4N28 Optocoupler, Phototransistor Output, FEATURES A 6 B Isolation test voltage 5000 V RMS Interfaces with common logic families C 2 5 C Input-output coupling capacitance < pf NC 3 4

More information

Optocoupler, Phototransistor Output, with Base Connection

Optocoupler, Phototransistor Output, with Base Connection CNY7 Optocoupler, Phototransistor FEATURES Isolation test voltage 5 V RMS A 6 B Long term stability i79 C NC 5 C E Industry standard dual-in-line package Lead (Pb-free component Component in accordance

More information

Reflective Optical Sensor with Transistor Output

Reflective Optical Sensor with Transistor Output Reflective Optical Sensor with Transistor Output CNY7 Description The CNY7 is a reflective sensor that includes an infrared emitter and phototransistor in a leaded package which blocks visible light. E

More information

Infrared Remote Control Receiver Module IRM-2638T

Infrared Remote Control Receiver Module IRM-2638T Block Diagram 1 2 3 Features High protection ability against EMI Circular lens for improved reception characteristics Line-up for various center carrier frequencies. Low voltage and low power consumption.

More information

Ambient Light Sensor

Ambient Light Sensor TEPT56 Ambient Light Sensor DESCRIPTION 94 839 TEPT56 ambient light sensor is a silicon NPN epitaxial planar phototransistor in a T-1¾ package. It is sensitive to visible light much like the human eye

More information

Silicon NPN Phototransistor

Silicon NPN Phototransistor Silicon NPN Phototransistor 16758-1 VEMT252X1 DESCRIPTION VEMT25X1 VEMT25X1 series are silicon NPN epitaxial planar phototransistors in a miniature dome lens, clear epoxy package for surface mounting.

More information

Optocoupler, Phototransistor Output, 4 Pin LSOP, Long Creepage Mini-Flat Package

Optocoupler, Phototransistor Output, 4 Pin LSOP, Long Creepage Mini-Flat Package Optocoupler, Phototransistor Output, 4 Pin LSOP, Long Creepage Mini-Flat Package FEATURES A 4 C Low profile package High collector emitter voltage, V CEO = 8 V 7295-6 DESCRIPTION The has a GaAs infrared

More information

Small Signal Fast Switching Diode

Small Signal Fast Switching Diode Small Signal Fast Switching Diode MECHANICAL DATA Case: SOD- Weight: approx.. mg Packaging codes/options: 8/K per " reel (8 mm tape), K/box 08/K per 7" reel (8 mm tape), K/box FEATURES Silicon epitaxial

More information

TSOP5700. IR Receiver for High Data Rate PCM at 455 khz VISHAY. Vishay Semiconductors

TSOP5700. IR Receiver for High Data Rate PCM at 455 khz VISHAY. Vishay Semiconductors IR Receiver for High Data Rate PCM at 455 khz Description The is a miniaturized SMD IR receiver for infrared remote control and IR data transmission. PIN diode and preamplifier are assembled on lead frame,

More information

Small Signal Fast Switching Diode FEATURES PART ORDERING CODE INTERNAL CONSTRUCTION TYPE MARKING REMARKS

Small Signal Fast Switching Diode FEATURES PART ORDERING CODE INTERNAL CONSTRUCTION TYPE MARKING REMARKS Small Signal Fast Switching Diode MARKING (example only) Bar = cathode marking XY = type code X Y 6 MECHANICAL DATA Case: SOD- Weight: approx.. mg Packaging codes/options: 8/K per " reel (8 mm tape), K/box

More information

IR Detector for Mid Range Proximity Sensor

IR Detector for Mid Range Proximity Sensor IR Detector for Mid Range Proximity Sensor 22531-1 DESCRIPTION The is a compact infrared detector module for proximity sensing application. It receives 38 khz modulated signals and has a peak sensitivity

More information

1 Form A Solid State Relay

1 Form A Solid State Relay Form A Solid State Relay VOAT, VOAABTR FEATURES 9 S S DC S' 3 S' High speed SSR - t on /t off < 8 μs Maximum R ON. Isolation test voltage 3 V RMS Load voltage V Load current A DC configuration DIP- package

More information

1 Form A Solid State Relay

1 Form A Solid State Relay 1 Form A Solid State Relay Vishay Semiconductors DIP i1791- SMD DESCRIPTION Vishay solid state relays (SSRs) are miniature, optically coupled relays with high-voltage MOSFET outputs. The LH1518 relays

More information

High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch)

High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch) High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch) DG2301 ishay Siliconix DESCRIPTION The DG2301 is a high-speed, 1-bit, low power, TTLcompatible bus switch. Using sub-micron CMOS technology,

More information

INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0

INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Package Dimensions INFRARED REMOTE CONTROL RECEIVER MODULE NOTES : 1. All dimensions are in millimeters. 2. Tolerance is ± 0.25(0.010") unless otherwise specified DRAWING NO.: DS-27-01-0001 DATE: 2004-08-31

More information

DG2302. High-Speed, Low r ON, SPST Analog Switch. Vishay Siliconix. (1-Bit Bus Switch with Level-Shifter) RoHS* COMPLIANT DESCRIPTION FEATURES

DG2302. High-Speed, Low r ON, SPST Analog Switch. Vishay Siliconix. (1-Bit Bus Switch with Level-Shifter) RoHS* COMPLIANT DESCRIPTION FEATURES High-Speed, Low r ON, SPST Analog Switch (1-Bit Bus Switch with Level-Shifter) DG2302 DESCRIPTION The DG2302 is a high-speed, 1-bit, low power, TTLcompatible bus switch. Using sub-micron CMOS technology,

More information

Optocoupler, Phototransistor Output, with Base Connection in SOIC-8 Package

Optocoupler, Phototransistor Output, with Base Connection in SOIC-8 Package Optocoupler, Phototransistor Output, FEATURES High BV CEO, 70 V Vishay Semiconductors i79002 A K NC NC 2 3 4 8 7 6 5 NC B C E Isolation test voltage, 4000 V RMS Industry standard SOIC-8A surface mountable

More information

Optocoupler, Phototransistor Output, AC Input

Optocoupler, Phototransistor Output, AC Input Optocoupler, Phototransistor Output, AC Input DESCRIPTION The SFH62A (DIP) and SFH626 (SMD) feature a high current transfer ratio, low coupling capacitance and high isolation voltage. These couplers have

More information

Optocoupler, Phototransistor Output, with Base Connection

Optocoupler, Phototransistor Output, with Base Connection Optocoupler, Phototransistor Output, with Base Connection FEATURES i794-4 DESCRIPTION This datasheet presents five families of Vishay industry standard single channel phototransistor couplers. These families

More information

Photovoltaic MOSFET Driver with Integrated Fast Turn-Off, Solid-State Relay

Photovoltaic MOSFET Driver with Integrated Fast Turn-Off, Solid-State Relay Photovoltaic MOSFET Driver with Integrated Fast Turn-Off, Solid-State Relay i7966_6 Turn Off FEATURES Open circuit voltage at I F = ma, 8. V typical Short circuit current at I F = ma, 5 μa typical Isolation

More information

Optocoupler, Phototransistor Output, with Base Connection, 300 V BV CEO

Optocoupler, Phototransistor Output, with Base Connection, 300 V BV CEO SFH64 Optocoupler, Phototransistor Output, with Base Connection, 3 V BV CEO i1794-3 DESCRIPTION The SFH64 is an optocoupler with very high BV CER, a minimum of 3 V. It is intended for telecommunications

More information

Standard 0603 SMD LED

Standard 0603 SMD LED TLMS, TLMO, TLMY, TLMG, TLMP, TLMB Standard 63 SMD LED DESCRIPTION 8562 The new 63 LED series have been designed in the smallest SMD package. This innovative 63 LED technology opens the way to smaller

More information

Optocoupler, Phototransistor Output, Dual Channel, SOIC-8 Package

Optocoupler, Phototransistor Output, Dual Channel, SOIC-8 Package ILD25T, ILD26T, ILD27T, ILD211T, ILD213T Optocoupler, Phototransistor Output, Dual Channel, SOIC-8 Package i17925 A1 C2 A3 C4 i17918-2 8C 7E 6C 5E DESCRIPTION The ILD25T, ILD26T, ILD27T, ILD211T, and ILD213T

More information

Optocoupler, Phototransistor Output, with Base Connection

Optocoupler, Phototransistor Output, with Base Connection HA/HA2/HA3/HA4/HA5 FEATURES Interfaces with common logic families Input-output coupling capacitance < pf Industry standard dual-in line 6-pin package A C NC 2 3 6 5 4 B C E Isolation test voltage: 5300

More information

BPW34. Silicon PIN Photodiode VISHAY. Vishay Semiconductors

BPW34. Silicon PIN Photodiode VISHAY. Vishay Semiconductors Silicon PIN Photodiode Description The is a high speed and high sensitive PIN photodiode in a miniature flat plastic package. Its top view construction makes it ideal as a low cost replacement of TO-5

More information

Optocoupler, Photodarlington Output, Dual Channel, SOIC-8 Package

Optocoupler, Photodarlington Output, Dual Channel, SOIC-8 Package Optocoupler, Photodarlington Output, i179042 DESCRIPTION A1 C 2 A3 C4 8 C 7E 6C 5E The ILD233T is a high current transfer ratio (CTR) optocoupler. It has a gallium arsenide infrared LED emitter and silicon

More information

2.5 A Output Current IGBT and MOSFET Driver

2.5 A Output Current IGBT and MOSFET Driver VO. A Output Current IGBT and MOSFET Driver 9 DESCRIPTION NC A C NC _ The VO consists of a LED optically coupled to an integrated circuit with a power output stage. This optocoupler is ideally suited for

More information

Schottky Rectifier, 1 A

Schottky Rectifier, 1 A Schottky Rectifier, 1 A BQPbF FEATURES SMB Cathode Anode Small foot print, surface mountable Low forward voltage drop High frequency operation Available RoHS* COMPLIANT Guard ring for enhanced ruggedness

More information

Schottky Rectifier, 1.0 A

Schottky Rectifier, 1.0 A Schottky Rectifier, 1.0 A VS-BQ060PbF Vishay High Power Products FEATURES Small foot print, surface mountable Low forward voltage drop SMB Cathode Anode High frequency operation Guard ring for enhanced

More information

Aluminum Electrolytic Capacitors Axial Miniature, Long-Life

Aluminum Electrolytic Capacitors Axial Miniature, Long-Life Aluminum Electrolytic Capacitors Axial Miniature, Long-Life 38 AML 0 ASM smaller dimensions Fig. QUICK REFERENCE DATA DESCRIPTION Nominal case sizes (Ø D x L in mm) 6.3 x.7 to 0 x 5 VALUE 0 x 30 to x 38

More information

Aluminum Electrolytic Capacitors Power Eurodin Printed Wiring

Aluminum Electrolytic Capacitors Power Eurodin Printed Wiring Aluminum Electrolytic Capacitors Power Eurodin Printed Wiring 00/0 PEDPW Fig. QUICK REFERENCE DATA DESCRIPTION VALUE 00 0 Nominal case size (Ø D x L in mm) x 0 to 0 x 00 Rated capacitance range 0 μf to

More information

Low Current SMD LED PLCC-2

Low Current SMD LED PLCC-2 Low Current SMD LED PLCC-2 VLMC31. 19225 DESCRIPTION These new devices have been designed to meet the increasing demand for low current SMD LEDs. The package of the VLMC31. is the PLCC-2 (equivalent to

More information

High Performance Schottky Rectifier, 1 A

High Performance Schottky Rectifier, 1 A High Performance Schottky Rectifier, A VS-MQNPbF Cathode Anode DO-24AC (SMA) PRODUCT SUMMARY Package DO-24AC (SMA) I F(AV) A V R V V F at I F.78 V I RM ma at 25 C T J max. 5 C Diode variation Single die

More information

Optocoupler, Phototransistor Output, High Reliability, 5300 V RMS, Low Input Current

Optocoupler, Phototransistor Output, High Reliability, 5300 V RMS, Low Input Current Optocoupler, Phototransistor Output, High Reliability, 53 V RMS, Low Input Current FEATURES A C 1 2 4 3 C E Operating temperature from -55 C to +11 C Good CTR linearity depending on forward current Isolation

More information

Aluminum Electrolytic Capacitors Radial Miniature, Low Impedance, High Vibration Capability

Aluminum Electrolytic Capacitors Radial Miniature, Low Impedance, High Vibration Capability Aluminum Electrolytic Capacitors Radial Miniature, Low Impedance, High Vibration Capability 048 RML 48 RUS lower longer life 36 RVI miniaturize 50 RMI high vibration FEATURES Very long useful life: 7000

More information

High Performance Schottky Rectifier, 3.0 A

High Performance Schottky Rectifier, 3.0 A High Performance Schottky Rectifier, 3. A Cathode Anode SMC PRODUCT SUMMARY Package SMC I F(AV) 3. A V R 4 V V F at I F.46 V I RM 3 ma at 25 C T J max. 5 C Diode variation Single die E AS 6. mj FEATURES

More information

High Performance Schottky Rectifier, 1.0 A

High Performance Schottky Rectifier, 1.0 A High Performance Schottky Rectifier, 1. A VS-BQ3-M3 Cathode Anode SMB PRODUCT SUMMARY Package SMB I F(AV) 1. A V R 3 V V F at I F.42 V I RM max. 15 ma at 125 C T J max. 15 C Diode variation Single die

More information

Aluminum Electrolytic Capacitors Power Economic Printed Wiring

Aluminum Electrolytic Capacitors Power Economic Printed Wiring Aluminum Electrolytic Capacitors Power Economic Printed Wiring 0/0 PECPW 00/0 PEDPW Fig. QUICK REFERENCE DATA DESCRIPTION high ripple current 0/0 PECPW long life 0 C Nominal case size (Ø D x L in mm) Rated

More information

Electrical Double Layer Energy Storage Capacitors Power and Energy Versions

Electrical Double Layer Energy Storage Capacitors Power and Energy Versions Electrical Double Layer Energy Storage Capacitors Power and Energy Versions FEATURES Polarized energy storage capacitor with high capacity and energy density Energy version with high stability available

More information

P-Channel 20 V (D-S) MOSFET

P-Channel 20 V (D-S) MOSFET Si30CDS P-Channel 0 V (D-S) MOSFET MOSFET PRODUCT SUMMARY V DS (V) R DS(on) ( ) I D (A) a Q g (Typ.) - 0 0. at V GS = - 4.5 V - 3. 0.4 at V GS = -.5 V -.7 3.3 nc TO-36 (SOT-3) FEATURES Halogen-free According

More information

UV SMD LED PLCC-2 FEATURES APPLICATIONS. at I F (ma) (ma) MIN. TYP. MAX. MIN. TYP. MAX. MIN. TYP. MAX.

UV SMD LED PLCC-2 FEATURES APPLICATIONS. at I F (ma) (ma) MIN. TYP. MAX. MIN. TYP. MAX. MIN. TYP. MAX. UV SMD LED PLCC-2 VLMU31 19225 DESCRIPTION The package of the VLMU31-series is the PLCC-2. It consists of a lead frame which is embedded in a white thermoplast. The reflector inside this package is filled

More information

DATA SHEET. TDA8560Q 2 40 W/2 Ω stereo BTL car radio power amplifier with diagnostic facility INTEGRATED CIRCUITS. 1996 Jan 08

DATA SHEET. TDA8560Q 2 40 W/2 Ω stereo BTL car radio power amplifier with diagnostic facility INTEGRATED CIRCUITS. 1996 Jan 08 INTEGRATED CIRCUITS DATA SHEET power amplifier with diagnostic facility Supersedes data of March 1994 File under Integrated Circuits, IC01 1996 Jan 08 FEATURES Requires very few external components High

More information

Dual Common-Cathode Ultrafast Plastic Rectifier

Dual Common-Cathode Ultrafast Plastic Rectifier (F,B)6AT thru (F,B)6JT Dual Common-Cathode Ultrafast Plastic Rectifier TO-0AB 6xT PIN PIN 3 PIN CASE 3 TO-63AB ITO-0AB F6xT PIN PIN 3 PIN 3 FEATURES Glass passivated chip junction Ultrafast recovery time

More information

Schottky Rectifier, 1.0 A

Schottky Rectifier, 1.0 A Schottky Rectifier, 1.0 A VS-BQ040-M3 Cathode Anode PRODUCT SUMMARY Package SMB I F(AV) 1.0 A V R 40 V V F at I F 0.38 V I RM 9 ma at 125 C T J max. 150 C Diode variation Single die E AS 3.0 mj FEATURES

More information

5 V, 1 A H-Bridge Motor Driver

5 V, 1 A H-Bridge Motor Driver , A H-Bridge Motor Driver DESCRIPTION The SIP200 is an integrated, buffered H-bridge with TTL and CMOS compatible inputs with the capability of delivering up to A continuous current at DD supply. The SIP200

More information

INTEGRATED CIRCUITS DATA SHEET. TDA7000 FM radio circuit. Product specification File under Integrated Circuits, IC01

INTEGRATED CIRCUITS DATA SHEET. TDA7000 FM radio circuit. Product specification File under Integrated Circuits, IC01 INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 May 1992 GENERAL DESCRIPTION The is a monolithic integrated circuit for mono FM portable radios, where a minimum on peripheral components

More information

Aluminum Capacitors Solid Axial

Aluminum Capacitors Solid Axial SAL-A End of Life. Last Available Purchase Date is -December- Radial higher CV/volume Fig. QUICK REFERENCE DATA DESCRIPTION VALUE Maximum case size (Ø D x L in mm) 6.7 x. to.9 x. Rated capacitance range

More information

DG2731/2732/2733. Low Voltage, 0.4 Ω, Dual SPDT Analog Switch. Vishay Siliconix. RoHS COMPLIANT FEATURES

DG2731/2732/2733. Low Voltage, 0.4 Ω, Dual SPDT Analog Switch. Vishay Siliconix. RoHS COMPLIANT FEATURES Low Voltage, 0.4 Ω, Dual SPDT Analog Switch DG273/2732/2733 DESCRIPTION The DG273/2732/2733 are low voltage, low on-resistance, dual single-pole/double-throw (SPDT) monolithic CMOS analog switches designed

More information

Schottky Rectifier, 100 A

Schottky Rectifier, 100 A Schottky Rectifier, A VS-BGQ Cathode Anode PowerTab PRODUCT SUMMARY Package PowerTab I F(AV) A V R V V F at I F 0.82 V I RM 180 ma at 125 C T J max. 175 C Diode variation Single die E AS 9 mj FEATURES

More information

Fiber Optics. Integrated Photo Detector Receiver for Plastic Fiber Plastic Connector Housing SFH551/1-1 SFH551/1-1V

Fiber Optics. Integrated Photo Detector Receiver for Plastic Fiber Plastic Connector Housing SFH551/1-1 SFH551/1-1V Fiber Optics Integrated Photo Detector Receiver for Plastic Fiber Plastic Connector Housing SFH551/1-1 Features Bipolar IC with open-collector output Digital output, TTL compatible Sensitive in visible

More information

Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications

Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications ELECTRICAL SPECIFICATIONS X7R GENERAL SPECIFICATION Note Electrical characteristics at +25 C unless otherwise specified

More information

Low Current SMD LED PLCC-2

Low Current SMD LED PLCC-2 Low Current SMD LED PLCC-2 VLMC31. 19225 DESCRIPTION These new devices have been designed to meet the increasing demand for low current SMD LEDs. The package of the VLMC31. is the PLCC-2 (equivalent to

More information

N-Channel 20-V (D-S) 175 C MOSFET

N-Channel 20-V (D-S) 175 C MOSFET N-Channel -V (D-S) 75 C MOSFET SUD7N-4P PRODUCT SUMMARY V DS (V) r DS(on) ( ) (A) a.37 @ V GS = V 37.6 @ V GS = 4.5 V 9 TO-5 D FEATURES TrenchFET Power MOSFET 75 C Junction Temperature PWM Optimized for

More information

INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30

INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30 INTEGRATED CIRCUITS IC24 Data Handbook 1997 Jun 30 FEATURES Wide supply voltage range of 1.2 V to 3.6 V In accordance with JEDEC standard no. 8-1A Inputs accept voltages up to 5.5 V CMOS low power consumption

More information

P6KE6.8A thru P6KE540A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. www.vishay.com FEATURES PRIMARY CHARACTERISTICS

P6KE6.8A thru P6KE540A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. www.vishay.com FEATURES PRIMARY CHARACTERISTICS TRANSZORB Transient Voltage Suppressors DO-204AC (DO-15) PRIMARY CHARACTERISTICS V WM 5.8 V to 459 V V BR uni-directional 6.8 V to 540 V V BR bi-directional 6.8 V to 440 V P PPM 600 W P D 5.0 W I FSM (uni-directional

More information

Power SMD LED PLCC-2 Plus

Power SMD LED PLCC-2 Plus Power SMD LED PLCC-2 Plus 2238 DESCRIPTION The VLMW51.. white LED in PLCC-2 plus package is an advanced product in terms of high luminous flux and low thermal resistance. In combination with the small

More information

P-Channel 60 V (D-S) MOSFET

P-Channel 60 V (D-S) MOSFET TP6K P-Channel 6 V (D-S) MOSFET G S PRODUCT SUMMARY V DS (V) R DS(on) ( ) V GS(th) (V) I D (ma) - 6 6 at V GS = - V - to - - 85 TO-6 (SOT-) Top View D Marking Code: 6Kwll 6K = Part Number Code for TP6K

More information

AC and Pulse Film Foil Capacitors KP Radial Potted Type

AC and Pulse Film Foil Capacitors KP Radial Potted Type AC and Pulse Film Foil Capacitors KP Radial Potted Type 0.5 L max. W max. Marking H max. FEATURES 5 mm lead pitch, supplied loose in box taped in ammopack or reel Material categorization: for definitions

More information

TDA2004R. 10 + 10 W stereo amplifier for car radio. Features. Description

TDA2004R. 10 + 10 W stereo amplifier for car radio. Features. Description 10 + 10 W stereo amplifier for car radio Features Low distortion Low noise Protection against: Output AC short circuit to ground Overrating chip temperature Load dump voltage surge Fortuitous open ground

More information

P-Channel 20-V (D-S) MOSFET

P-Channel 20-V (D-S) MOSFET Si33DS P-Channel -V (D-S) MOSFET PRODUCT SUMMARY V DS (V) R DS(on) (Ω) I D (A).39 at V GS = -.5 V -.7 -.5 at V GS = -.5 V -..68 at V GS = -.8 V - 3.5 FEATURES Halogen-free According to IEC 69-- Available

More information

Thick Film Resistor Networks, Dual-In-Line, Molded DIP

Thick Film Resistor Networks, Dual-In-Line, Molded DIP Thick Film Resistor Networks, Dual-In-Line, Molded DIP FEATURES Isolated, bussed, and dual terminator schematics available 0.160" (4.06 mm) maximum seated height and rugged, molded case construction Thick

More information

AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC

AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC QUICK REFERENCE DATA DESCRIPTION VALUE Ceramic Class 1 2 Ceramic Dielectric U2J U2J Y5S, Y5U Y5S, Y5U Voltage (V AC ) 500 760

More information

TDA2003 10W CAR RADIO AUDIO AMPLIFIER

TDA2003 10W CAR RADIO AUDIO AMPLIFIER TDA2003 10W CAR RADIO AUDIO AMPLIFIER DESCRIPTION The TDA 2003 has improved performance with the same pin configuration as the TDA 2002. The additional features of TDA 2002, very low number of external

More information

How To Control A Power Supply On A Powerline With A.F.F Amplifier

How To Control A Power Supply On A Powerline With A.F.F Amplifier INTEGRATED CIRCUITS DATA SHEET Sound I.F. amplifier/demodulator for TV File under Integrated Circuits, IC02 March 1986 GENERAL DESCRIPTION The is an i.f. amplifier with a symmetrical FM demodulator and

More information

SuperTan Extended (STE) Capacitors, Wet Tantalum Capacitors with Hermetic Seal

SuperTan Extended (STE) Capacitors, Wet Tantalum Capacitors with Hermetic Seal SuperTan Extended () Capacitors, Wet Tantalum Capacitors with Hermetic Seal FEATURES SuperTan Extended () represents a major breakthrough in wet tantalum capacitor Available technology. Its unique cathode

More information

Infrared Transceiver, 9.6 kbit/s to 115.2 kbit/s (SIR)

Infrared Transceiver, 9.6 kbit/s to 115.2 kbit/s (SIR) Infrared Transceiver, 9.6 kbit/s to 115.2 kbit/s (SIR) DESCRIPTION 20206 The is one of the smallest IrDA compliant transceivers available. It supports data rates up to 115 kbit/s. The transceiver consists

More information

DATA SHEET. TDA1510AQ 24 W BTL or 2 x 12 W stereo car radio power amplifier INTEGRATED CIRCUITS

DATA SHEET. TDA1510AQ 24 W BTL or 2 x 12 W stereo car radio power amplifier INTEGRATED CIRCUITS INTEGRATED CIRCUITS DATA SHEET 24 W BTL or 2 x 12 W stereo car radio File under Integrated Circuits, IC01 January 1992 GENERAL DESCRIPTION The is a class-b integrated output amplifier encapsulated in a

More information

Baseband delay line QUICK REFERENCE DATA

Baseband delay line QUICK REFERENCE DATA FEATURES Two comb filters, using the switched-capacitor technique, for one line delay time (64 µs) Adjustment-free application No crosstalk between SECAM colour carriers (diaphoty) Handles negative or

More information

1.5KE6.8A thru 1.5KE540A, 1N6267A thru 1N6303A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. www.vishay.

1.5KE6.8A thru 1.5KE540A, 1N6267A thru 1N6303A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. www.vishay. TRANSZORB Transient Voltage Suppressors Case Style.5KE FEATURES Glass passivated chip junction Available in uni-directional and bi-directional 500 W peak pulse power capability with a /0 μs waveform, repetitive

More information

TSL250, TSL251, TLS252 LIGHT-TO-VOLTAGE OPTICAL SENSORS

TSL250, TSL251, TLS252 LIGHT-TO-VOLTAGE OPTICAL SENSORS TSL50, TSL5, TLS5 SOES004C AUGUST 99 REVISED NOVEMBER 995 Monolithic Silicon IC Containing Photodiode, Operational Amplifier, and Feedback Components Converts Light Intensity to Output Voltage High Irradiance

More information

Power MOSFET FEATURES. IRF520PbF SiHF520-E3 IRF520 SiHF520. PARAMETER SYMBOL LIMIT UNIT Drain-Source Voltage V DS 100 V Gate-Source Voltage V GS ± 20

Power MOSFET FEATURES. IRF520PbF SiHF520-E3 IRF520 SiHF520. PARAMETER SYMBOL LIMIT UNIT Drain-Source Voltage V DS 100 V Gate-Source Voltage V GS ± 20 Power MOSFET PRODUCT SUMMARY (V) 100 R DS(on) ( ) = 0.7 Q g (Max.) (nc) 16 Q gs (nc) 4.4 Q gd (nc) 7.7 Configuration Single TO0AB G DS ORDERING INFORMATION Package Lead (Pb)free SnPb G D S NChannel MOSFET

More information

DATA SHEET. TDA1518BQ 24 W BTL or 2 x 12 watt stereo car radio power amplifier INTEGRATED CIRCUITS

DATA SHEET. TDA1518BQ 24 W BTL or 2 x 12 watt stereo car radio power amplifier INTEGRATED CIRCUITS INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 July 1994 GENERAL DESCRIPTION The is an integrated class-b output amplifier in a 13-lead single-in-line (SIL) plastic power package.

More information

High-Bandwidth, Low Voltage, Dual SPDT Analog Switches

High-Bandwidth, Low Voltage, Dual SPDT Analog Switches DG, DG High-Bandwidth, Low Voltage, Dual SPDT Analog Switches DESCRIPTION The DG/DG are monolithic CMOS dual single-pole/double-throw (SPDT) analog switchs. They are specifically designed for low-voltage,

More information

Standard Recovery Diodes, Generation 2 DO-5 (Stud Version), 95 A

Standard Recovery Diodes, Generation 2 DO-5 (Stud Version), 95 A Standard Recovery Diodes, Generation 2 DO-5 (Stud Version), 95 A 95PF(R)... DO-203AB (DO-5) PRODUCT SUMMARY I F(AV) Package Circuit configuration 95PF(R)...W DO-203AB (DO-5) 95 A DO-203AB (DO-5) Single

More information

N-Channel 60-V (D-S) MOSFET

N-Channel 60-V (D-S) MOSFET 7/7, VQJ/P, BS7 -Channel 6-V (D-S) MOSFET Part umber V (BR)DSS Min (V) r DS(on) Max ( ) V GS(th) (V) I D (A) 7 5 @ V GS = V.8 to. 7 7.5 @ V GS = V to.5.5 VQJ 6 5.5 @ V GS = V.8 to.5.5 VQP 5.5 @ V GS =

More information

GP2Y0D810Z0F. Distance Measuring Sensor Unit Digital output (100 mm) type GP2Y0D810Z0F

GP2Y0D810Z0F. Distance Measuring Sensor Unit Digital output (100 mm) type GP2Y0D810Z0F GP2Y0D810Z0F Distance Measuring Sensor Unit Digital output (100 mm) type Description GP2Y0D810Z0F is distance measuring sensor unit, composed of an integrated combination of PD (photo diode), IRED (infrared

More information

DDSL01. Secondary protection for DSL lines. Features. Description

DDSL01. Secondary protection for DSL lines. Features. Description Secondary protection for DSL lines Features Stand off voltage: 30 V Surge capability: I pp = 30 A 8/20 µs Low capacitance device: 4.5 pf at 2 V RoHS package Low leakage current: 0.5 µa at 25 C 3 2 Description

More information

HEF4011B. 1. General description. 2. Features and benefits. 3. Ordering information. 4. Functional diagram. Quad 2-input NAND gate

HEF4011B. 1. General description. 2. Features and benefits. 3. Ordering information. 4. Functional diagram. Quad 2-input NAND gate Rev. 6 10 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a quad 2-input NAND gate. The outputs are fully buffered for the highest noise

More information