PLEASE FIND HARDWARE IN RED POLYBAG BEFORE DISCARDING PACKING MATERIAL. HARDWARE LIST PARTS LIST (A) RIGHT SIDE PANEL 1PC (H) TOP PANEL 1PC

Transcription

1 STYLE NO. FA5583 FAUX STONE/OAK SOUTHERN ENTERPRISES INC. LISA FIREPLACE RELAX...If you can follow a few easy, step-by-step directions in order.you CAN ASSEMBLE THIS ITEM. PLEASE FIND HARDWARE IN RED POLYBAG BEFORE DISCARDING PACKING MATERIAL. HARDWARE LIST (1) WOOD DOWEL 10PCS (5) WASHER 8PCS Ø6X30mm (2) FLAT HEAD WOOD SCREW 20PCS (6) WRENCH 1PC Ø8X22mm (3) MACHINE SCREW 8PCS (7) PAN HEAD WOOD SCREW 2PCS Ø1/4 x1-1/2 (4) LOCK WASHER 8PCS Ø3X12mm PARTS LIST (A) RIGHT SIDE PANEL 1PC (H) TOP PANEL 1PC (B) LEFT SIDE PANEL 1PC (I) FIREBOX 1PC (C) RIGHT FRONT PANEL 1PC (J) FIREBOX LEFT DOOR 1PC

2 (D) LEFT FRONT PANEL 1PC (K) FIREBOX RIGHT DOOR 1PC (E) MIDDLE FRONT PANEL 1PC (L) MANTEL LOG 1PC (F) BASE 1PC (M) MANTEL GRATE 1PC (G) WOOD CONNECTOR 2PCS NOTE: THIS CARTON DOES NOT INCLUDE PARTS I, J, K, L, M. ASSEMBLY INSTRUCTION 1. SELECT A SMOOTH, SOFT SURFACE TO PREVENT SCRATCHING FINISH. 2. YOU MAY NEED A PHILLIP SCREWDRIVER. 3. INSERT WOOD DOWELS (1) INTO PREDRILLED HOLES ON EDGE OF RIGHT FRONT PANEL (C) AND FIT INTO CORRESPONDING HOLES ON INSIDE OF RIGHT SIDE PANEL (A). INSERT FLAT HEAD WOOD SCREWS (2) THROUGH PREDRILLED HOLES ON WOOD BARS ON BACK OF RIGHT FRONT PANEL (C) AND TIGHTEN INTO CORRESPONDING HOLES ON RIGHT SIDE PANEL (A). PERFORM THE SAME WAY TO ASSEMBLE LEFT SIDE PANEL AND FRONT PANEL (B, D). AS FIGURE 1 SHOWN. 4. INSERT WOOD DOWELS (1) INTO PREDRILLED HOLES ON BOTH ENDS OF MIDDLE FRONT PANEL (E) AND FIT INTO CORRESPONDING HOLES ON EDGES OF LEFT AND RIGHT FRONT PANELS (D, C). AS FIGURE 2 SHOWN.

3 FIGURE 1 FIGURE 2 SHOWN BACK VIEW FOR ASSEMBLY PURPOSES 5. INSERT MACHINE SCREWS (3) THROUGH LOCK WASHERS (4), WASHERS (5) AND PREDRILLED HOLES ON WOOD BARS ON BOTTOM OF LEFT AND RIGHT SIDE PANEL (B, A) AND TIGHTEN INTO THREADED HOLES ON UPSIDE OF BASE (F). AS FIGURE 3 SHOWN. 6. INSERT WOOD DOWELS (1) INTO PREDRILLED HOLES ON BOTTOM EDGES OF LEFT AND RIGHT FRONT PANELS (D, C) AND FIT INTO CORRESPONDING HOLES ON UPSIDE OF BASE (F). TIGHTEN FLAT HEAD WOOD SCREWS (2) THROUGH PREDRILLED HOLES ON WOOD CONNECTORS (G) INTO CORRESPONDING HOLES ON BACK OF PARTS (C, D, E). AS FIGURE 3 SHOWN. 7. INSERT MACHINE SCREWS (3) THROUGH LOCK WASHERS (4), WASHERS (5) AND PREDRILLED HOLES ON LEFT AND RIGHT SIDE PANELS (B, A) AND TIGHTEN INTO THREADED HOLES ON TOP PANEL (H). AS FIGURE 4 SHOWN. FIGURE 3 FIGURE 4 SHOWN BACK VIEW FOR ASSEMBLY PURPOSES

4 8. FIT THE DOORS (J, K) ON FIREBOX (I). AND INSERT FIREBOX INTO THE SPACE OF ABOVE UNIT. MAKE SURE FIREBOX (I) IS PRESSED TIGHTLY AGAINST THE ASSEMBLED UNIT. INSERT PAN HEAD WOOD SCREWS (7) THROUGH PREDRILLED HOLES ON BOTTOM OF FIRE BOX (I) AND TIGHTEN INTO CORRESPONDING HOLES ON BASE (F). PLACE MANTEL LOG (L) UPRIGHT ON THE MANTEL GRATE (M) JUST BEHIND THE L-BRACKETS. SET MANTEL GRATE (M) IN THE FIREBOX (I) WITH THE L-BRACKETS FACING OUT. POSITION IT SO THAT IT IS CENTERED WITHIN THE FIREBOX (I). PLACE ONE, TWO, OR THREE FUEL CANS (DO NOT INCLUDED) BEHIND THE LOG ON THE MANTEL GRATE (M). AS FIGURE 5-7 SHOWN. FIGURE 5 FIGURE 6 FIGURE 7 READY YOUR NEW FAUX STONE/OAK LISA FIREPLACE IS FINISHED AND READY TO USE.

5 CAUTIONS: 1. REMOVE THE PAPER LABEL WHEN LIGHT THE FUEL CANS. 2. DO NOT BURN MORE THAN THREE CANS OF FUEL AT ONCE. 3. USE LONG MATCHES TO LIGHT THE CANS OF FUEL. 4. DO NOT TOUCH THE CAN WITH BARE HANDS UNTIL THE FLAME HAS BEEN EXTINGUISHED FOR 20 MINUTES. 5. DO NOT BURN ANYTHING EXCEPT THE CANS OF FUEL IN THE FIREBOX. Please count, identify and compare parts and hardware list to be sure all parts are present. It may help to divide parts and label them to correspond with part list. Extra hardware may be included. If any items are missing, please contact our parts/service department at (800) or in Dallas (972) / 9am 4pm Mon-Fri Central time. Missing or damaged hardware and/ or parts will be replaced free of charge. WE DO NOT SELL PARTS. WE DO NOT RECOMMEND MODIFYING PRODUCT(S) AND WE ARE NOT RESPONSIBLE FOR ANY DAMAGES DUE TO PRODUCT MODIFICATION(S). If this product has not been purchased from our retail affiliates (within 9 months), we are under no obligation to provide parts or replacement merchandise. Parts will not be available for items arriving fully assembled. "We will ship parts if available" "This is not a warranty" PARTS REPLACEMENT FORM STYLE NO: FA5583 Customer Name PARTS LETTER PART DESCRIPTION QUANTITY NEEDED Street, City, State, Zip Phone# Please indicate where you purchased this item. Store/website/catalog SOUTHERN ENTERPRISES INC. P.O. Box Dallas, Texas / / Please indicate color/size/style number / /