AB/AG. General purpose direct acting 2, 3 port solenoid valve. (General purpose valve) For air, vacuum, water, oil CONTENTS.

Transcription

1 / (eneral purpose valve) eneral purpose direct acting, 3 port solenoid valve For air, vacuum, water, oil N/ US/ F/ F/ Overview The general purpose valve series enables control of various types of fluids including water, air, oil and vacuums. In addition to the high reliability and high quality of the valve, a variety of options and variations are available. Features Various working fluids control Various types of fluids can be handled by selecting the proper body material and sealant. Wide option range Including open frame, coil with diode and terminal boxes. great variety of series and variations Including direct acting compact type Rc/8 (port size) to Rc. CONTENTS Series variation 0 Coil selection guide Safety precautions port solenoid valve Discrete valve NC (normally closed) type 6 3/ NC (normally closed) type 30 NO (normally open) type 30 7 (large bore size) NC (normally closed) type Manifold 3/35, /5 NC (normally closed) type 8 NO (normally open) type 58 3 port solenoid valve Discrete valve 3/ Universal type 66 33/3 NC pressurization type 8 3/ NO pressurization type 0 Manifold 3*/* (common supply / individual exhaust type) Universal type 7 35*/5* (common supply / separate flow type) Universal type 7 33*/3* (common supply / individual exhaust type) NC pressurization type 9 3*/* (actuator) NO pressurization type 0 Electronic Catalog file list 8 lways read the precautions in the Introduction and page before starting use. FV FW/ F FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting, 3 port solenoid valve

2 eneral purpose valve variation Series variation eneral purpose direct acting, 3 port solenoid valve No. of port port Model 3// Structure Discrete ctuation NC (normally closed) type ir Low vacuum (.33 x 0 Pa (abs)) 7 3 NO (normally open) type 7 NC (normally closed) type 3 35 Manifold NC Common supply (normally closed) Individual supply type Common supply 5 Individual supply NO (normally open) type Common supply 3 port 3 Discrete Universal type 33 NC pressurization type 3 3 NO pressurization type Manifold ctuator Manifold Common supply / Universal type individual exhaust Common supply / separate flow Common supply / individual exhaust Common supply / separate flow NC pressurization type Common supply / individual exhaust 3 ctuator NO pressurization type

3 Working fluid Water Kerosene Oil (50 mm /s or less) ot water Port size Steam Rc/8 Rc/ Rc3/8 Rc/ Rc3/ Rc Page 6 N/ US/ F/ F/ * * 30 FV * * * * * FW/ F * * * * * * *3 * *3 * *3 * *3 * * * * * * * * * * * * * * * * * * * *3 7 * *3 7 * * *3 *3 7 * * *3 *3 7 * *3 9 * * *3 *3 9 * *3 0 * * *3 *3 0 * Refer to page for details on the coil system. *: 0 mm /s for 7 Series. *: Port : Rc/, port C: Rc3/8 *3: indicates the NO port. *: Refer to each ow to order column for the thread types. FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting, 3 port solenoid valve

4 Coil selection guide Coil housing types and selection guide wide variety is available to match applications. Refer to the structure and features to select the optimum model. Direct acting, 3 port solenoid valve (///) eat proof class mold DC and C (50/60 z common) eat proof temperature 30 C Protection property symbols: IP6 or equivalent Outdoor use not available rommet lead wire Lead wire length 300 mm ppearance lank 6C eat proof class mold eat proof class mold DC and C (50/60 z common) eat proof temperature 30 C Protection property symbols: IP6 or equivalent Outdoor use not available DC and C (50/60 z common) eat proof temperature 30 C Protection property symbols: IP65 or equivalent Outdoor use not available Lead wire DIN terminal box Easy wiring and maintenance Reliable electric protection (ground terminal) Light available (optional-00/00 VC and VDC only) Lead wire length 300 mm Conduit (CTC9) for direct conduit wiring can be mounted E 6E eat proof class mold DC and C (50/60 z common) eat proof temperature 30 C Protection property symbols: IP or equivalent Outdoor use not available P terminal box Easy wiring Light available (optional-00/00 VC and /00 VDC only) 3M 3N eat proof class mold DC and C (50/60 z common) eat proof temperature 30 C Protection property symbols: IP65 or equivalent Outdoor use not available P terminal box Easy wiring Light available (optional-00/00 VC and /00 VDC only) 3I 3J Coil variation eat proof class taped C dedicated (50/60 z common) igh temperature fluid and high ambient temperature available eat proof temperature 80 C Protection property symbols: IP00 Outdoor use not available Lead wire Lead wire length 300 mm Conduit (CTC9) for direct conduit wiring can be mounted Open frame type eat proof class mold with diode diode is mounted on the coil section for direct-current conversion (C-DC conversion) Perfect for places where beat can be a problem C dedicated (50/60 z common) eat proof temperature 30 C Protection property symbols: IP65 or equivalent Outdoor use not available Lead wire P terminal box Easy wiring Light available (optional-00/00 VC only) Lead wire length 300 mm Conduit (CTC9) for direct conduit wiring can be mounted M N 5 eat proof class mold with diode diode is mounted on the coil selection for direct-current conversion (C-DC conversion) Perfect for places where beat can be a problem C dedicated (50/60 z common) eat proof temperature 30 C Protection property symbols: IP or equivalent Outdoor use not available P terminal box Easy wiring Light available (optional-00/00 VC only) 5M 5N eat proof class mold with diode diode is mounted on the coil selection for direct-current conversion (C-DC conversion) Perfect for places where beat can be a problem C dedicated (50/60 z common) eat proof temperature 30 C Protection property symbols: IP65 or equivalent Outdoor use not available P terminal box Easy wiring Light available (optional-00/00 VC only) 5I 5J Conduit Use a conduit (CTC9 or /) when using direct conduit wiring for the open frame lead wire.

5 Repair parts table per coil option Coil option symbol Voltage Repair parts Plunger assembly Core assembly Coil assembly ctuator assembly * N/ 0 or blank C US/ 6C *, *3 DC F/ F/ E E 6E 6 6 *, *3 C DC DC FV FW/ F 3 C DC FL 3M 3N 3I 3J C DC C DC C P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ M N 5 5M 5N 5I 5J C C C C *: The actuator assembly includes the coil assembly, core assembly and plunger assembly. *: s 6C, 6E, 6 and 6 are dedicated parts, they are provided as part of the actuator assembly. *3: It is available only for. MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting, 3 port solenoid valve

6 Safety precautions lways read this section before starting use. Direct acting, 3 port solenoid valve (///) Working fluid () Consult with CKD before using this valve for active gas (combustion gas, acetylene gas, etc.). () Valves for LP (propane gas, butane gas) are available as custom order, so consult with CKD. (3) When using this valve for dry air or inert gas, the life can be shortened considerably due to wear. Use a valve for dry air. () This valve cannot be used for maintaining the vacuum. Consult with CKD when the vacuum needs to be maintained. 3 WRNIN Caution Design & Selection Continuous energizing Use the NO pressurization type when using the 3 port valve in a continuously energized state with the NO port pressurized. When continuously energizing the universal or NC pressurization type, use a fluoro rubber seal. Suction sound With the C voltage specifications, a large suction sound may be heard momentarily after energizing. To avoid the suction sound, select the coil with diode or the DC voltage. The suction sound will drop. Fluid viscosity The fluid viscosity must be 50 mm /s or less. Malfunctions could occur if the viscosity is higher than 50 mm /s. Leakage current from other fluid control components When operating the solenoid valve with a programmable controller, etc., check that the output leakage current from the programmable controller is within the following specifications. Failure to observe this could lead to malfunctions. Voltage, C C diode DC 00 V 00 V 00 V 00 V V V 6 m or less 3 m or less m or less Triode C switch Programmable controller side m or less CR circuit C R m or less Leakage current Solenoid valve m or less CUTION When Using Manual operation lways observe the following points when using a manual override. <For NC (normally closed) type> Opening: Insert a flat-tip screwdriver into the slit on the manual shaft, and turn it approx. 0 to the right or left. The plunger will rise up and the valve will open. (For the 3 port valve, the NC side valve seat will open and the NO side valve seat will close.) The open state is held even when the screwdriver is removed. lways return the valve to the original position after use. Closing: Turn the manual shaft from the open position to the vertical position. The plunger will lower and the valve will close. (For the 3 port valve, the NC side valve seat will close and the NO side valve seat will open.) (Refer to the following drawings.) C O O C Valve closed Valve opened Valve opened <For NO (normally open) type> () Closing the valve with manual operations The manual shaft is threaded, so hold the manual dial and rotate the shaft clockwise. When the manual dial has been rotated downward 5 to 6 mm and no longer rotates, the solenoid valve will switch to closing operation. () Resetting (when not using manual override) lways rotate the manual dial counterclockwise and return it to the highest point. C O Manual dial Manual shaft Right-handed thread Installation, Piping & Wiring CUTION Piping () lways hold the socket with a spanner, etc., if the NO side is a socket. () When passing steam, steam generated from a boiler will contain a large amount of drainage. lways install a drain trap. (3) When passing steam, water replenished to the boiler will contain matters such as "calcium salt" and "magnesium salt". These matters will react with oxygen and carbon oxide causing scales and sludge, so always install a "water softener" and a filter for steam. Wiring () Refer to page 53 in the Introduction for details on connecting the terminal box. CUTION Maintenance When disassembling or assembling, tighten the core assembly and socket with the following tightening torques. Core assembly tightening torque 30 to 5 N m 30 to 5 N m Socket tightening torque - 8 to 6 N m Nut tightening torque 8 to 6 N m 8 to 6 N m

7 CUTION Working environment IP65 (IEC6059 (IEC59:989-)) standards are applied to the test. void use in conditions where water or cutting oil could directly contact the valve. N/ US/ F/ F/ FV Explanation of protection property symbols and examination method of IP65 Protective structure Note: IP-65 is a standard as followings. IEC (International Electrotechnical Commission) standards st characteristic number (protection grade for foreign solid) rade Degree of protection Dust proof type Powder and dust do not enter inside. 6 IP-** Protection property symbols (International Protection) nd characteristic number (protection grade for entry of water) rade Degree of protection Overview of test method (fresh water is used) 5 Protection for jet No harmful effects occur even when water is sprayed with nozzles from all directions. (IEC6059 (IEC59:989-)) Using the following test device, spray water for minute per m of test sample (exterior) surface area from all directions, for a total of 3 minutes or more..5 to 3 m.5 L/min. Spray nozzle inner diameter: ø6.3 mm FW/ F FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting, 3 port solenoid valve

8 Direct acting port solenoid valve (general purpose valve) Series NC (normally closed) type Port size: Rc/8, Rc/ JIS symbol OUT IN Common specifications Item Working fluid Working pressure differential range Max. working pressure Withstanding pressure (water) Fluid temperature mbient temperature eat proof class tmosphere Valve structure Valve seat leakage Mounting attitude MPa MPa MPa C C cm 3 /min. (NR) ir, water, kerosene, oil (50 mm /s or less) 0 to.5 (refer to max. working pressure differential in individual specifications.) to 0 (no freezing) -0 to 50 Place free of corrosive gas and explosive gas Direct acting poppet structure 0. or less Free Individual specifications Item Orifice Port size (mm) Rc/8 Rc/ Max. working pressure differential (MPa) ir Water, kerosene Oil (50 mm /s) C DC C DC C DC Rated voltage 00 VC 50/60 z 0 VC 60 z 00 VC 50/60 z 0 VC 60 z pparent power (V) Power consumption (W) olding Starting C DC 50 z 60 z 50 z 60 z 50/60 z /. 7 Flow characteristics NC (normally closed) type Port size Rc/8 Rc/ Orifice (mm) Flow characteristics C [dm 3 /(s bar)] b Cv flow factor *: Effective sectional area S and sonic conductance C are converted as S 5.0 x C.

9 Series ow to order 0 00 C00V Port size Orifice C ody/sealant combination * * D Option E Rated voltage *3 Symbol Port size lank Orifice Std. Option Rc/8 Rc/ ø.5 ø ø3 ø C ody/sealant combination ody lank 00 luminum rass None Mounting plate Descriptions Sealant Nitrile rubber Fluoro rubber Nitrile rubber Fluoro rubber Refer to page 36 in the Introduction for details on the material combinations. D Option E Rated voltage C00V 00 VC 50/60 z, 0 VC 60 z C00V 00 VC 50/60 z, 0 VC 60 z Remarks ir, kerosene, oil ir, kerosene, oil ir, water, kerosene, oil ir, water, kerosene, oil Consult with CKD for other optional voltages. N/ US/ F/ F/ FV FW/ F FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ <Example of model number> C00V : Port size: Rc/8 Orifice: ø.5 C ody/sealant combination: : ody - brass, sealant - nitrile rubber D Option: Mounting plate E Rated voltage: 00 VC 50/60 z, 0 VC 60 z Note on model no. selection *: For (orifice ø.5), only C or is available. *: When using for water, select the brass (option symbol: or ) body. *3: The voltage fluctuation must be within ±0% of the rated voltage. *: Leave C blank for standard. owever, to select 00 for D, indicate 0 for C. MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting port solenoid valve

10 Series Internal structure and parts list Series 3 IN OUT No. Parts name Material Coil Core assembly Stainless steel 3 O ring Shading coil Fluoro rubber Copper 5 Plunger spring Stainless steel Plunger Sealant ody Stainless steel Nitrile or fluoro rubber luminum or brass Dimensions -0/0- to 5-* Mounting plate -0/0- to 5-*00 * Lead wire length 50 mm ø (6) ø5.5 -ø6 0 -Rc/8 or / Dimensions shown in ( ) are for brass body. 8 Mounting plate No. E M5 depth 8

11 3 Series Discrete direct acting port solenoid valve (general purpose valve) 3 Series NC (normally closed) type Series NO (normally open) type Port size: Rc/8 to Rc/ JIS symbol Common specifications 3/: NC (normally closed) type Item Standard specifications Optional specifications OUT Working fluid ir, low vacuum (.33 x 0 Pa (abs)), water, kerosene, oil (50 mm /s or less) ot water Steam Working pressure differential range MPa Withstanding pressure (water) MPa 0 to 5 (refer to max. working pressure differential in individual specifications. ) 5 IN Fluid temperature (Note ) C -0 to 60-0 to 90-0 to 8 : NO (normally open) type mbient temperature eat proof class C -0 to 60-0 to 00 OUT tmosphere Valve structure Place free of corrosive gas and explosive gas Direct acting poppet structure IN Valve seat leakage cm 3 /min. (NR) 0. or less (air) 300 or less (air) Mounting attitude Free ody, sealant rass, nitrile rubber rass, ethylene propylene diene rubber rass, PTFE Note : No freezing Individual specifications Item Port size Orifice (mm) NC (normally closed) type Rc/ Rc/ Rc/ Rc3/8 Rc3/8 Rc/ NO (normally open) type Rc/ Rc3/ Max. working pressure differential (MPa) ir Water, hot water, kerosene Oil (50 mm /s) Steam C DC C DC C DC C (0.03) (0.03) 0.05 (0.03) *8 *8 * Max. working pressure (MPa) 5 5 (fluid; for steam) Rated voltage 00 VC 50/60 z 0 VC 60 z 00 VC 50/60 z 0 VC 60 z VDC VDC 8 VDC 00 VDC 5 (fluid; for steam) pparent power (V) Power consumption (W) olding Starting C 50 z 60 z 50 z 60 z 50/60 z / /5.7 (8.) * / () *: The model numbers above show the basic port size (Rc) and orifice diameter. Refer to ow to order for other combinations (e.g., for steam). *: The port size symbol is 0 for Rc/8 (6), 0 for Rc/ (8), 03 for Rc3/8 (0) and 0 for Rc/ (5). *3: Refer to DC column for the max. working pressure differential of coil with diode. *: The voltage fluctuation must be within ±0% of the rated voltage. *5: Power consumption of coil housing E// is indicated. *6: When using with a low vacuum, vacuum the OUT port side. *7: Power consumption of coil housing 6C/6E/6/6 is indicated. *8: The DC voltage of coil housing E// and the max. working pressure differential of coil housing 6C/6/6 are indicated. DC Weight (kg) (Rc/) 5 () *5 (Rc3/8) (7) * (Rc/) 0.5 (Rc3/8)

12 3 Series Optional specifications (fluid temperature, ambient temperature, valve seat leakage) Sealant material Fluoro rubber Ethylene propylene diene rubber PTFE Coil (heat proof class) Fluid temperature (Note ) C mbient temperature C Valve seat leakage cm 3 /min. (NR) -0 to 60-0 to 60-0 to 90-0 to 00 (Note ) -0 to 60-0 to 60-0 to 90-0 to 00 (Note ) -0 to 60-0 to 60-0 to 8-0 to 00 (Note ) 0. or less (air) 300 or less (air) Note : No freezing Note : The range is -0 to 80 C when using the P terminal box with indicator light for the coil housing. N/ US/ F/ F/ Flow characteristics NC (normally closed) type NO (normally open) type Port size Rc/8 Rc/ Rc/ Rc3/8 Rc3/8 Rc/ Rc/ Rc3/8 Orifice (mm) *: Effective sectional area S and sonic conductance C are converted as S 5.0 x C. *: Values shown in ( ) are for stainless steel body Flow characteristics C [dm 3 /(s bar)] b Cv flow factor (.5). (.9) 3.0 (.6) (.5). (.9) 3.0 (.6).8 (.6) 9.3 (8.) (.5). (.9) 3.0 (.6).8 (.6) (7) 8 (7) (0.38) (7) 8 (7) (0.38) 0.9 (0.37) 0.36 (0.3) (7) 8 (7) (0.38) 0.9 (0.37) (0) 0.5 (8) 0.8 (0.6) (0) 0.5 (8) 0.8 (0.6) (0.8).88 (.5) (0.6) (0.8) FV FW/ F FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting port solenoid valve

13 3 Series ow to order NC (normally closed) type 3 Port size: Rc/ Orifice: ø3 The combinations indicated with in the above table are available. C ody/sealant combination: ody - brass, sealant - nitrile rubber D Coil housing: rommet lead wire E to I : lank J Rated voltage: 00 VC 50/60z, 0 VC 60z Note on model no. selection Note on C 0 Port size S C00V Orifice D Coil housing Other options J Voltage E Manual override (locking) Surge suppressor F Mounting plate I Copper and PTFE free C ody/sealant combination * * *3 * *5 *6 *7 <Example of model number> C00V : 3 <Example of model number> -0-3-C00V : Port size Orifice Port size: Rc/ Orifice: ø3 C ody/sealant combination: ody - brass, sealant - nitrile rubber D Coil housing: rommet lead wire E Manual override (locking): Selected F to : lank I Surge suppressor: Selected J Rated voltage: 00 VC 50/60z, 0 VC 60z Symbol Descriptions Symbol Descriptions Symbol ø.5 ø ø3 ø3.5 ø ø5 ø7 ø0 C ody/sealant combination ody Sealant Treatment Remarks lank C V D E F W J K P L M N R D to J Std. rass or bronze Option Stainless steel Stainless steel rass Rc/8 Rc/ Rc3/8 Rc/ 3 Nitrile rubber Fluoro rubber PTFE Fluoro rubber Nitrile rubber Fluoro rubber PTFE Fluoro rubber Nitrile rubber Fluoro rubber PTFE Ethylene propylene diene rubber Nitrile rubber Fluoro rubber PTFE Ethylene propylene diene rubber *: *: *3: *: *5: *6: *7: /8 / 3/8 / - Vacuum inspection - Vacuum inspection Oil free ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 8 C *) Medium vacuum ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 8 C *) Medium vacuum ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 8 C *) ot water (up to 90 C *) ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 8 C *) ot water (up to 90 C *) 3 Low pressure large flow rate Refer to page 36 in the Introduction for details on the material combinations. Refer to the following page for details on the coil housing, other options and voltage, etc. N N 3N N Descriptions /8NPT /NPT 3/8NPT /NPT Leave blank for standard. owever, to select options in D to I, indicate 0 for C. When, M or N is selected for D. The body for the low pressure large flow rate is bronze (standard) or stainless steel (optional). For option symbols V and W, vacuum is inspected at "leakage amount:.33 x 0-6 Pa m 3 /s or less". When C of the low pressure large flow rate is V or W, DC voltage is not available. The ethylene propylene diene rubber seal combination (C P/R) cannot be used with air. (Compressed air contains oil, and ethylene propylene diene rubber is not oil-resistant. ) When C is C, F, K, P, N or R, the coil housings D 6C, 6E, 6 and 6 cannot be selected.

14 3 Series For D to J, the combinations indicated with symbols can be manufactured. Note that if options E to I are not required, no symbol is indicated. D Coil housing E F Other options I J Rated voltage Cable gland Conduit Descriptions (Marine cable gland) (Conduit pipe) Descriptions -5a -5b -5c CTC9 / lank E 3 3M 3N 3I 3J M N 5 5M 5N 5I 5J 6C 6E 6 6 lank 6C Std. Option rommet lead wire DIN terminal box DIN terminal box DIN terminal box + small light (Pg) Open frame type Open frame type (heat proof class ) (/) (Pg) Lead wire P terminal box (/) P terminal box + light (/) P terminal box (IP65 or equivalent) (/) (/) P terminal box + light (IP65 or equivalent) Lead wire P terminal box P terminal box + light Lead wire P terminal box (/) (/) Open (/) frame type P terminal box + light (/) (diode integrated) P terminal box (IP65 or equivalent) (/) P terminal box + light (IP65 or equivalent) (/) rommet lead wire 7W DIN terminal box (/) 7W DIN terminal box (Pg) 7W DIN terminal box + small light (Pg) 7W Manual override (locking) Mounting plate rommet lead wire 300 mm S P6 D E F D E F D E F Surge suppressor S S S Copper and PTFE free P6 P6 P6 P6 00 VC, 00 VC 00 VC, 00 VC VDC, VDC, 8 VDC, 00 VDC 00 VC, 00 VC, VDC 00 VC, 00 VC VDC, VDC, 8 VDC, 00 VDC 00 VC, 00 VC, VDC, VDC, 00 VDC 00 VC, 00 VC, VDC, VDC, 8 VDC, 00 VDC 00 VC, 00 VC, VDC, VDC, 00 VDC 00 VC, 00 VC 00 VC, 00 VC VDC, VDC VDC Refer to the following precautions for D to J. Conduit (CTC9) (/) N/ US/ F/ F/ FV FW/ F FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP E 6E M 3N M N 5M 5N 3I 3J 5I 5J DIN terminal box Open frame type grommet lead wire 300 mm (heat proof class ) 5 (diode integrated) Open frame P terminal box M, N (heat proof class ) 5M, 5N (diode integrated) Open frame P terminal box (IP65 or equivalent) 5I, 5J (diode integrated) Refer to page for coil selection. Note on model no. selection Note on D *8: Leave blank for the standard coil housing. owever, to select options in E to I, indicate 00 for D. *9: 5, 5M, 5N, 5I and 5J are coils for which C power is converted to DC with a diode. *0: DC coil for steam is available for. Contact CKD for more information. *: 6C, 6E, 6 or 6 can be selected for only. *: The coil housings 6C, 6E and 6 are VDC and VDC dedicated. 6 is VDC dedicated. Note on E to I *3: The manual override (E ) is not available for the low pressure large flow rate *: When C is C, F, K, N, V or W, the manual override (E ) is not available. *5: Select one among D, E, F, and for. *6: The surge suppressor is an accessory for the lead wire coil. When selecting a coil with terminal box, the surge suppressor is mounted in the terminal box. *7: s standard, the surge suppressor is incorporated in the coil with diode and the VDC coil (D /6), so the surge suppressor symbol S cannot be selected. *8: I P6 is available only when C is L, M or R. *9: Tropicalization (rust-proof coating) is available as a measure against rust. Contact CKD for more information. Note that the tropicalization is not available when the manual override option and the coil option 6C/6E/6/6 are selected. Note on J *0: 00 VC coil is compatible with 00 VC 50/60 z and 0 VC 60 z, and 00 VC coil is compatible with 00 VC 50/60 z and 0 VC 60 z. Note that the coils D 5/5M/5N/5I/5J can be used only with 00 VC 50/60 z or 00 VC 50/60 z. *: For voltages other than above, consult with CKD. *: The lead wire is available in the standard 300 mm length, and 500 mm, 000 mm, 000 mm and 3000 mm lengths. Contact CKD for more information. C/ MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting port solenoid valve

15 3 Series ow to order NO (normally open) type 0 L 3 P6 C00V Port size Orifice <Example of model number> -0--C00V : Port size: Rc/ Orifice: ø.5 C ody/sealant combination: D Coil housing: E to I : J Rated voltage: D Coil housing Other options E Manual override (locking) Surge suppressor F Mounting plate C ody/sealant combination * * *3 * ody - brass, sealant - nitrile rubber rommet lead wire lank 00 VC 50/60z, 0 VC 60z J Voltage I Copper and PTFE free Symbol Descriptions Port size 0 Rc/ 03 Rc3/8 Orifice Std. Option D to J ø.5 ø ø3 ø3.5 ø ø5 ø7 C ody/sealant combination ody Sealant Treatment Remarks lank Nitrile rubber ir, water, low vacuum, kerosene (up to 60 C) Fluoro rubber - ir, low vacuum, kerosene (up to 90 C *) C PTFE Steam (up to 8 C *) V Fluoro rubber Vacuum inspection Medium vacuum D Nitrile rubber ir, water, low vacuum, kerosene (up to 60 C) E Fluoro rubber - ir, low vacuum, kerosene (up to 90 C *) F PTFE Steam (up to 8 C *) W Fluoro rubber Vacuum inspection Medium vacuum Nitrile rubber ir, water, low vacuum, kerosene (up to 60 C) J Fluoro rubber ir, low vacuum, kerosene (up to 90 C *) K PTFE Steam (up to 8 C *) P Ethylene propylene diene rubber ot water (up to 90 C *) L Nitrile rubber Oil free ir, water, low vacuum, kerosene (up to 60 C) M Fluoro rubber ir, low vacuum, kerosene (up to 90 C *) N PTFE Steam (up to 8 C *) R Ethylene propylene diene rubber ot water (up to 90 C *) rass Stainless steel Stainless steel rass Symbol 3 Descriptions / 3/8 Symbol N 3N Descriptions /NPT 3/8NPT Refer to page 36 in the Introduction for details on the material combinations. Refer to the following page for details on the coil housing, other options and voltage, etc. <Example of model number> S-C00V : Port size: Rc3/8 Orifice: ø5 C ody/sealant combination: ody - brass, sealant - nitrile rubber D Coil housing: rommet lead wire E Manual override (locking): Selected F : lank Surge suppressor: Selected J Rated voltage: 00 VC 50/60z, 0 VC 60z Note on model no. selection Note on C *: Leave blank for standard. owever, to select options in D to I, indicate 0 for C. *: When, M or N is selected for D. *3: For option symbols V and W, vacuum is inspected at "leakage amount:.33 x 0-6 Pa m 3 /s or less". *: The ethylene propylene diene rubber seal combination (C P/R) cannot be used with air. (Compressed air contains oil, and ethylene propylene diene rubber is not oil-resistant. )

16 3 Series For D to J, the combinations indicated with symbols can be manufactured. Note that if options E to I are not required, no symbol is indicated. D Coil housing E F Other options I J Rated voltage Cable gland Conduit Descriptions (Marine cable gland) (Conduit pipe) Descriptions -5a -5b -5c CTC9 / lank E 3 3M 3N 3I 3J M N 5 5M 5N 5I 5J lank E Std. Option rommet lead wire DIN terminal box DIN terminal box (/) (Pg) DIN terminal box + small light (Pg) Lead wire P terminal box (/) Open frame type P terminal box + light (/) P terminal box (IP65 or equivalent) (/) P terminal box + light (IP65 or equivalent) (/) Open Lead wire frame type P terminal box (/) (heat proof class ) P terminal box + light (/) Lead wire Open P terminal box (/) frame type P terminal box + light (/) (diode integrated) P terminal box (IP65 or equivalent) (/) P terminal box + light (IP65 or equivalent) (/) Manual override (locking) Mounting plate rommet lead wire 300 mm DIN terminal box D E F D E F D E F S S S Surge suppressor Copper and PTFE free P6 P6 P6 P6 00 VC, 00 VC 00 VC, 00 VC VDC, VDC, 8 VDC, 00 VDC 00 VC, 00 VC, VDC 00 VC, 00 VC VDC, VDC, 8 VDC, 00 VDC 00 VC, 00 VC, VDC, VDC, 00 VDC 00 VC, 00 VC, VDC, VDC, 8 VDC, 00 VDC 00 VC, 00 VC, VDC, VDC, 00 VDC 00 VC, 00 VC 00 VC, 00 VC Refer to the following precautions for D to J. Conduit (CTC9) (/) N/ US/ F/ F/ FV FW/ F FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ 3 5 3M 3N M N 5M 5N 3I 3J 5I 5J Open frame type grommet lead wire 300 mm (heat proof class ) 5 (diode integrated) Open frame P terminal box M, N (heat proof class ) 5M, 5N (diode integrated) Open frame P terminal box (IP65 or equivalent) 5I, 5J (diode integrated) * Refer to page for coil selection. Note on model no. selection Note on D *5: Leave blank for the standard coil housing. owever, to select options in E to I, indicate 00 for D. *6: 5, 5M, 5N, 5I and 5J are coils for which C power is converted to DC with a diode. Note on E to I *7: When C is C, F, K, N, V or M, the manual override (E ) is not available. *8: Select one among D, E, F, and for. *9: The surge suppressor is an accessory for the lead wire coil. When selecting a coil with terminal box, the surge suppressor is mounted in the terminal box. *0: s standard, the surge suppressor is incorporated in the coil with diode and the VDC coil (D ), so the surge suppressor symbol S cannot be selected. *: I P6 is available only when C is L. *: Tropicalization (rust-proof coating) is available as a measure against rust. Contact CKD for more information. Note that the tropicalization is not available when the manual override option is selected. Note on J *3: 00 VC coil is compatible with 00 VC 50/60 z and 0 VC 60 z, and 00 VC coil is compatible with 00 VC 50/60 z and 0 VC 60 z. Note that the coils D 5/5M/5N/5I/5J can be used only with 00 VC 50/60 z or 00 VC 50/60 z. *: For voltages other than above, consult with CKD. *5: The lead wire is available in the standard 300 mm length, and 500 mm, 000 mm, 000 mm and 3000 mm lengths. Contact CKD for more information. Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting port solenoid valve

17 3 Series Internal structure and parts list 3 Series -0/03- to IN OUT 8-03/ No. 3 Parts name Material Coil Core assembly SUS05 or equivalent, 36L, 03 * Stainless steel Shading coil Cu (g for stainless steel body) Copper (silver for stainless steel body) Plunger SUS05 or equivalent Stainless steel No. Parts name Material 5 Plunger spring SUS30 Stainless steel NR (FKM, EPDM, PTFE) NR: Nitrile rubber 6 O ring (size: S568-09) 37 Sealant NR (FKM, EPDM, PTFE) ( FKM: EPDM: Fluoro rubber PTFE: Tetrafluoroethylene Ethylene propylene resin ) diene rubber 8 ody C377 or CC08 (SCS3) rass or bronze (stainless steel) *: When the body/sealant combination symbol is other than blank or, or when the coil housing is 6C, 6E, 6 or 6, the material is SUS05 or equivalent, 36L, 30. *: ( ) shows option. Note that PTFE is not available for

18 3 Series Internal structure and parts list N/ US/ F/ No. Parts name Material No. Parts name Material Core assembly SUS05 or equivalent, 36L, 30 Stainless steel 6 O ring Coil 3 Plunger SUS05 or equivalent Stainless steel 7 Spring Shading coil Cu (g for stainless steel body) Copper (silver for stainless steel body) 38 ody NR: Nitrile rubber (EPDM: Ethylene propylene diene rubber) 5 Sealant NR (FKM, EPDM, PTFE) 9 NO valve (FKM: Fluoro rubber) (PTFE: Tetrafluoroethylene resin) IN OUT NR (FKM, EPDM, PTFE) (size: S568-09) SUS30 C377 (SUS303) POM (SUS303, PF) NR: Nitrile rubber (EPDM: Ethylene propylene diene rubber) (FKM: Fluoro rubber) (PTFE: Tetrafluoroethylene resin) Stainless steel rass (stainless steel) Option symbol : lank/0/d//l/v/w - polyacetal resin : Other than above - stainless steel, perfluoroalkoxy resin ( ) shows option. F/ FV FW/ F FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting port solenoid valve

19 3 Series Dimensions: 3 Series rommet lead wire type 3-0/0- to 6-* lank F Note : The 3 Series is an open when energized type port solenoid valve. The body and sealant materials are combined according to the working fluid, and the orifice and pressure are selected according to the relation of the required flow rate and pressure. The coil specifications are determined according to the fluid temperature and ambient conditions, allowing the optimum valve to be selected. Note : The dimensions are the same for the or NPT thread port size. D 75 IN OUT 36 -M5 depth 8 8 Rc/8 (0) Rc/ (0) 8 CKD * Lead wire length 300 mm 3-0- to 6-C -0- to 6-C D F 3

20 3 Series Optional dimensions: 3 Series DIN terminal box 3-0/0- to 6-* E C 7.5 * Refer to the grommet lead wire type dimensions on the left page for common dimensions. Open frame lead wire type 3-0/0- to 6-* N/ US/ F/ F/ 39 () D FV FW/ F Voltage C (E//) DC (E//) Dimensions shown in ( ) are for /. C D (50) (5.5) 0.5 FL Open frame type + P terminal box 3-0/0- to 6-* 3 M M 5 N N I J Stainless steel body 3-0/0- to 6- D/E/F/R/W/L/M/N lank ø37.5 D D Open frame type + conduit 3-0/0- to 6-* (56) Manual override (locking) 3-0/0- to 6-*** Figure shows the brass body. IN Manual override OUT (ø37.5) 38 CTC9 (/) Dimensions shown in ( ) are for /. Dimensions shown in ( ) are for stainless steel body. P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order Mounting plate 3-0/0- to 6-*** eneral purpose valve Direct acting port solenoid valve 8 -ø5.5 -ø6 Mounting plate No. E-0006

21 3 Series Dimensions: Series rommet lead wire type -0/03- to 7-* lank 6C F IN OUT C D E -M5 depth 8 Rc/ (0) Rc3/8 (03) 8 CKD * Lead wire length 300 mm -0- to 6-C -0-7-C -03- to 7-C -0- to 6-6C-DC C-DC -03- to 7-6C-DC C D E F rommet lead wire type -03/0-8-* lank 6C F OUT CKD 5 D 93 IN C -0-8-C C-DC C-DC 8 D F M5 Depth 8 Note : Note : Rc3/8 (03) -Rc/ (0) This Series, port solenoid valve, open when energized, is designed to meet the customer's requirement according to working fluid, body and seal materials, relation between flow rate and the required pressure (converted to orifice diameter and pressure), and ambient temperature and conditions (converted to coil specifications). The dimensions are the same for the or NPT thread port size.

22 3 Series Optional dimensions: Series DIN terminal box -0/03/0- to 8-* 6 F E 7.5 * Refer to the grommet lead wire type dimensions on the left page for common dimensions. Open frame lead wire type -0/03/0- to 8-* N/ US/ F/ 39 () I E D F/ FV FW/ Dimensions shown in ( ) are for /. Voltage F I C (E//) DC (E//) DC (6E/6/6) (53.5) 5.5 (5) 56.5 (56) Open frame type + P terminal box -0/03/0- to 8-* 3 M M 5 N N I 03 J Stainless steel body -0/03/0- to 8- D/F/R/W/L/M/N/E -0- to 6-** -0-7-** -03- to 7-** -03/0-8-** Open frame type + conduit -0/03/0- to 8-* 3 5 D (60) E Dimensions shown in ( ) are for /. CTC9 (/) F FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ D E Manual override (locking) -0/03- to 7-*** Figure shows the brass body. MX/ Other.P. systems -0- to 6-C -0-7-C -03- to 7-C C -0-8-C Mounting plate -0/03/0- to 8-*** 6 (70) 50 (58) 8 (8) C C D E ø ø5.0 50* *: The max. dimension is ø5. -ø5.5 -ø6 Dimensions shown in ( ) are for mounting plate No.. IN Note: No manual override is available for -03/0-8. K -0- to 6-*** -0-7-*** -03- to 7-*** 36 (ø37.5) 0 (ø5.0) Dimensions shown in ( ) are for stainless steel body. Mounting plate No. E-0006 Mounting plate No. E-0059 Manual override OUT K pplicable model -0/03- to 7 Series Stainless steel body -0- to 6- D/E/F/L/M/N/R/W -03/0-8 Series Stainless steel body D/E/F/L/M/N/R/W -03- to 7- D/E/F/L/M/N/R/W PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting port solenoid valve

23 3 Series Dimensions: Series rommet lead wire type -0/03- to E <Reference> port direct acting valve, closed when energized, is open when de-energized. This type is commonly used to be continuously energized. The dimensions are the same for the or NPT thread port size. IN OUT D Note : The dimensions are the same for the or NPT thread port size. C Rc/ (0) Rc3/8 (03) -M5 depth 8 8 CKD * Lead wire length 300 mm -0- to to 7 C D E

24 3 Series Optional dimensions: Series DIN terminal box -0/03- to 7-* E F 7.5 * Refer to the grommet lead wire type dimensions on the left page for common dimensions. Open frame lead wire type -0/03- to 7-* N/ US/ F/ F/ 39 () 3 E D FV FW/ F Voltage C DC Dimensions shown in ( ) are for /. F (53.5) (60) -0- to to 7 D E FL Open frame type + P terminal box -0/03- to 7-* 3 M M 5 N N I J Open frame type + conduit -0/03- to 7-* (60) Dimensions shown in ( ) are for /. CTC9 (/) P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP Stainless steel body -0/03- to 7- D/E/F/R/W/L/M/N Manual override (locking) -0/03- to 7-*** C/ MX/ -0- to to 7 Mounting plate -0/03- to 7-*** 6 (70) 50 (58) C D E C D ø ø ø ø5.5 -ø6 E Dimensions shown in ( ) are for mounting plate No.. (3) Code Mounting plate No. E-0006 Mounting plate No. E-0059 Manual override pplicable model -0/03- to 7 Series Stainless steel body -0- to 6- D/E/F/L/M/N/R/W Stainless steel body D/E/F/L/M/N/R/W -03- to 7- D/E/F/L/M/N/R/W Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Direct acting port solenoid valve

25 3 Series Large bore size direct acting port solenoid valve (general purpose valve) 7 Series NC (normally closed) type Port size: Rc/, Rc3/, Rc JIS symbol OUT IN Specifications Item Working fluid ir, water, kerosene, oil (0 mm /s) Working pressure ir C: 0 to 00, DC: 0 to 80 C: 0 to 70, DC: 0 to 0 C: 0 to 0, DC: 0 to 30 range kpa Water, kerosene, oil C: 0 to 80, DC: 0 to 80 C: 0 to 50, DC: 0 to 0 C: 0 to 30, DC: 0 to 30 Withstanding pressure (water) MPa Fluid viscosity mm /s 0 or less Fluid temperature C mbient temperature C Valve seat leakage cm 3 /min. (NR) -5 to 60 (no freezing) -0 to or less (air) Port size Rc/ Rc3/ Rc Orifice mm 5 8 Mounting attitude Limited to vertical position with coil facing upward to horizontal position Electric specifications Rated voltage 00 VC 50/60 z, 00 VC 50/60 z, 0 VC 60 z, 0 VC 60 z, VDC, VDC, 8 VDC, 00 VDC pparent olding (50/60 z) 3/6 power V Starting (50/60 z) 3/06 Power consumption W C: 3/ (50/60 z), DC: 0 Flow characteristics Port size Rc/ Rc3/ Rc Orifice (mm) 5 8 Flow characteristics C [dm 3 /(s bar)] b Cv flow factor S (mm ) *: Effective sectional area S and sonic conductance C are converted as S 5.0 C.

26 7Series ow to order 7 5 C00V N/ Port size F Other options US/ Symbol Port size 5 Rc/ 0 Rc3/ 5 Rc 5 8 J Orifice ody ronze ronze Orifice Stuffing rass rass C ody/sealant combination Descriptions D Coil housing ø (only 7-5 (port size Rc/)) ø5 (only 7-0 (port size Rc3/)) ø8 (only 7-5 (port size Rc)) C ody/sealant combination E Mounting plate Sealant Fluoro rubber Fluoro rubber Treatment D Oil free Voltage D Coil housing E F Other options Rated voltage Cable gland Conduit Descriptions (Marine cable gland) (Conduit pipe) Descriptions -5a -5b -5c CTC9 / C E 3 3M 3N 5 5M 5N Std. Option rommet lead wire DIN terminal box DIN terminal box DIN terminal box + small light Open frame type Open frame type (diode integrated) Lead wire P terminal box P terminal box + light Lead wire P terminal box (/) (Pg) (Pg) (/) (/) (/) P terminal box + light (/) D E F D E F For D to, the combinations indicated with symbols can be manufactured. Note that if options E and F are not required, no symbol is indicated. Mounting plate <Example of model number> 7-5--E-C00V : 7 Port size: Rc/ Orifice: ø C ody/sealant combination: D Coil housing: E Mounting plate: F Other options: Rated voltage: ody - bronze, stuffing - brass, sealant - fluoro rubber DIN terminal box (/) Selected lank 00 VC 50/60z, 0 VC 60z 00 VC, 00 VC 00 VC, 00 VC VDC, VDC, 8 VDC, 00 VDC 00 VC, 00 VC, VDC, 00 VDC 00 VC, 00 VC F/ F/ FV FW/ F FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order Note on model no. selection Note on C *: Refer to page 36 in the Introduction for details on the material combinations. Note on D *: Refer to page for coil selection. *3: 5, 5M and 5N are coils for which C power is converted to DC with a diode. *: When working fluid is air, type 5 is recommended. *5: Contact CKD for details on the heat proof class coil. Note on F *6: Select one among D, E, F, and for F. Note on *7: 00 VC coil is compatible with 00 VC 50/60 z and 0 VC 60 z, and 00 VC coil is compatible with 00 VC 50/60 z and 0 VC 60 z. Note that the coils D 5/5K/5 can be used only with 00 VC 50/60 z or 00 VC 50/60 z. *8: For voltages other than above, consult with CKD. *9: Lead wire length is 300 mm. dditional lengths are available in 500 mm increments. Contact CKD for details. eneral purpose valve Discrete direct acting port solenoid valve

27 7 Series Internal structure and parts list 3 IN OUT No. Parts name Material 3 Coil Plunger Wear ring SUS05 PTFE Stuffing assembly C377 (Core assembly) SUS05, Cu Spring pin Main valve Main valve spring ody SUS0 SUS30, FKM SUS30 CC07 Stainless steel Tetrafluoroethylene resin rass Stainless steel, copper Stainless steel Stainless steel, fluoro rubber Stainless steel ronze Dimensions rommet lead wire type 7-*-*-*C Mounting plate 7-*-*-** (300) 8 C D CKD E F J -K C D E F J K Rc/ Rc3/ Rc ø9 ø9 ø

28 7Series Optional dimensions DIN terminal box 7-*-*-* E Open frame lead wire type 7-*-*-* (300) N/ US/ F/ F/ 6.5 (6) 33 FV FW/ F Dimensions shown in ( ) are for /. FL Open frame type + P terminal box 7-*-*-* 3 M 5 N Open frame type + conduit 7-*-*-* 3 5 Dimensions shown in ( ) are for /. P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Discrete direct acting port solenoid valve 5 59 (6) CTC9 (/)

29 Direct acting port solenoid valve, manifold and actuator (general purpose valve) 3/35//5 Series NC (normally closed) type Common supply type (port C pressurization), individual supply type (port pressurization) JIS symbol 3/ (Common supply type / port C pressurization) Port Port OUT OUT IN IN Port C 35/5 (Individual supply type / port pressurization) Port Port IN IN OUT OUT Port C Common specifications Item Working fluid Working pressure differential range Max. working pressure Withstanding pressure (water) Fluid temperature (Note ) mbient temperature eat proof class tmosphere Valve structure Valve seat leakage Mounting attitude ody, sealant Note : No freezing Standard specifications Optional specifications irflow, low vacuum (.33 x 0 Pa (abs)), water, kerosene, oil (50 mm /s or less) ot water Steam MPa 0 to 5 (refer to max. working pressure differential in individual specifications. ) MPa 5 MPa 0 C C -0 to 60-0 to 60-0 to 90-0 to 8-0 to 00 Place free of corrosive gas and explosive gas Direct acting poppet structure cm 3 /min. (NR) 0. or less (air) 300 or less (air) Free rass, nitrile rubber rass, ethylene propylene diene rubber rass, PTFE Individual specifications 3/ / Port size Orifice (mm) Max. working pressure differential (MPa) ir Water, hot water, kerosene Oil (50 mm /s) Steam C DC C DC C DC C Rated voltage 00 VC 50/60 z 0 VC 60 z 00 VC 50/60 z 0 VC 60 z VDC VDC 8 VDC 00 VDC *: The model numbers above show the basic orifice diameter. Refer to ow to order for other combinations (e.g., for steam). *: Refer to ow to order (page 50) and Dimensions (page 5) for the port size. *3: Refer to DC column for the max. working pressure differential of coil with diode. *: The voltage fluctuation must be within ±0% of the rated voltage. *5: Power consumption of coil housing E// is indicated. *6: When using with a low vacuum, vacuum the NO port side. *7: Power consumption of coil housing 6C/6E/6/6 is indicated. pparent power (V) Power consumption (W) olding Starting C DC 50 z 60 z 50 z 60 z 50/60 z / /5.7 (8.) *5 () *5 (7) *7

30 3355 Series Optional specifications (fluid temperature, ambient temperature, valve seat leakage) Sealant Fluoro rubber Ethylene propylene diene rubber PTFE Coil (heat proof class) Fluid temperature (Note ) C mbient temperature C Valve seat leakage cm 3 /min. (NR) -0 to 60-0 to 60-0 to 90-0 to 00 (Note ) -0 to 60-0 to 60-0 to 90-0 to 00 (Note ) -0 to 60-0 to 60-0 to 8-0 to 00 (Note ) 0. or less (air) 300 or less (air) Note : No freezing Note : The range is -0 to 80 C when using the P terminal box with indicator light for the coil housing. N/ US/ F/ F/ Flow characteristics 3/ / Port size *: Effective sectional area S and sonic conductance C are converted as S 5.0 x C. Orifice Flow characteristics (mm) C [dm 3 /(s bar)] b Cv flow factor FV FW/ F FL P/ D PK/ DK For dry air Explosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems PD/FD/ PJ CVE/ CVSE CPE/ CPD Medical analysis Custom order eneral purpose valve Discrete direct acting port solenoid valve

31 3355 Series ow to order Common supply type (port C pressurization) Individual supply type (port pressurization) Common supply type (port C pressurization) Individual supply type (port pressurization) <Example of model number> 3--3-C00V : 3 (common supply type / port C pressurization) Type of thread: Orifice: ø.5 C Station no.: 3 stations D ody/sealant combination: E F I Coil housing: to : Rated voltage: 5 3 S C00V Type of thread Orifice C Station no. * D ody/sealant combination *3 * *5 *6 ody - brass, sealant - nitrile rubber rommet lead wire lank 00 VC 50/60z, 0 VC 60z E Coil housing Surge suppressor F Manual override (locking) Other options Symbol Type of thread lank Rc N NPT Orifice ø.5 ø ø3 ø3.5 ø ø5 ø7 I Voltage Descriptions C Station no. to 0 0 stations to 0 stations ctuator only D ody/sealant combination ody Sealant Treatment Remarks lank C D E F J K P L M N R Std. Option E to I rass Stainless steel Stainless steel rass Nitrile rubber Fluoro rubber PTFE Nitrile rubber Fluoro rubber PTFE Nitrile rubber Fluoro rubber PTFE Ethylene propylene diene rubber Nitrile rubber Fluoro rubber PTFE Ethylene propylene diene rubber The combinations indicated with in the above table are available. Oil free ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 8 C *) ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 8 C *) ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 8 C *) ot water (up to 90 C *) ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 8 C *) ot water (up to 90 C *) Refer to page 36 in the Introduction for details on the material combinations. Refer to the following page for details on the coil housing, other options and voltage, etc. <Example of model number> S-C00V : 35 (individual supply type / port pressurization) Type of thread: Rc Orifice: ø C Station no.: stations D ody/sealant combination: ody - brass, sealant - nitrile rubber E Coil housing: rommet lead wire F Manual override (locking): Selected Other options: lank Surge suppressor: Selected I Rated voltage: 00 VC 50/60z, 0 VC 60z Note on model no. selection *: Orders for only the masking plate and sub-plate are also available. Contact CKD for details. Note on C and D *: Consult with CKD about more than 0 stations manifold. *3: Leave blank for standard. owever, to select options in E to, indicate 0 for D. *: When, M or N is selected for D. *5: The ethylene propylene diene rubber seal combination (D P/R) cannot be used with air. (Compressed air contains oil, and ethylene propylene diene rubber is not oil-resistant. ) *6: When D is C, F, K, P, N or R, the coil housings E 6C, 6E, 6 and 6 cannot be selected.