JTAG Programmer. Overview. Features. Trenz Electronic GmbH 1
|
|
- Franklin Lester
- 7 years ago
- Views:
Transcription
1 Rev.0 as of 000 Trenz Electronic GmbH Brendel 0 Bünde, Germany JTAG Programmer User's Manual Overview The JTAG Programmer is designed for level conversion between the parallel port (LPT) and a JTAG interface. It is fully compatible to the Xilinx parallel cable III, with improved reliabilty, caused by Schmitt Trigger inputs on the LPT side. It features the old Xilinx pin JTAG connector, as well as the new pin header with mm pitch. For ease of use with Trenz Electronic FPGA Boards, an additional 0 pin header with,mm pitch is added, which is capable of powering the programmer, even with JTAG voltage levels below.v. Features Level conversion between parallel (LPT) and JTAG port Fully compatible with Xilinx parallel cable III Adapter can be powered by the target Flexible power supply input via JTAG port, or USB JTAG voltage level adjustment by reference input voltage Improved reliabilty, due to Schmitt Trigger inputs on the LPT side Figure : JTAG Programmer Trenz Electronic GmbH
2 TMS JTAG Programmer Details To locate the connectors on the board see Figure. TCK TDO TDI Parallel port D-Sub HDR HDR HDR0 0 0 Jumper USB USB connector Figure : Location of jumper and connectors Power Supply The programmer requires a.v powersupply on the LPT side. There are three options, selectable with Jumpers. Attention: Short only one Jumper at the same time. External powered via USB If you have a low voltage (below.v) JTAG chain, and can't use connector HDR0, you have to supply the programmer externaly. Simply connect an USB cable. Set jumper to USB. Powered by target using If your target board implements a.v JTAG chain, you can power the programmer with the line from any of the JTAG connectors. Set the jumper to. Powered by target using If your target supports the pinout of the HDR0 connector, the.v line can be used to power the programmer. Set the jumper to. Trenz Electronic GmbH
3 JTAG connectors There are three JTAG connectors available. The voltage level of the JTAG signals depends on the reference input voltage. It ranges between V and V. HDR Supports the older version of the Xilinx connector. Figure : HDR HDR Supports the newer version of the Xilinx connector. J 0 J H D R Parallel port To connect your JTAG programmer to the PC use a standard parallel cable. n S T R O B E n A U T O F D D a ta 0 n E R R O R D a ta n IN IT D a ta n S L C T IN D a ta D a ta D a ta D a ta D a ta n A C K B U S Y P E S L C T J D B D IN S E N S E C L K P C T R L P R O G D O N E Figure : Parallel port USB connector This connector is only provided for power supply. It has no USB related function. 0 0 H D R Figure : HDR HDR0 Proprietary (compatibel to Trenz Electronic Spartan- Baseboards) connector, featuring an extra voltage line for programmer power supply with low voltage JTAG chains. J 0 H D R 0 Figure : HDR0 Note: Starting with Revision 0 of the JTAG Programmer, Pin is no longer connected Trenz Electronic GmbH
4 Schematics Figure shows the voltage level conversion schematic and figure the power supply schematic. S E N S E R PP output U A R R D M B R 00 V R E F.k k C 0.u U C D O N E R PP output 0 U A P R O G R U B U E 0 R 0 C p V R EF input/output U A U F U B D IN C T R L R R U A U F R C p U C U D U C P R R 0 C p U B U E U D C LK R 0 R C 0 p Figure : schematic of driver section U B S H L D _ J U S B G G C 0 0 p R M + D- D+ D D L + C +. u C 0. u D D L Figure : schematic of power supply section C. u VUSB C 0. u VUSB J P C 0. u V C C J P V R E F J P U S B C 0. u - U D - U C - U D - Trenz Electronic GmbH
5 Ordering Details Packing List JTAG Adapter Parallel cable JTAG cable with AMP Micromatch connector, suitable for HDR0 Order number The Order Number is: TE0-00 Revision History Rev. Date Who Description TS Created TT Pin of J changed Table : Revision History Trenz Electronic GmbH
How To Build A Prototyg Carrier Board For Industrial Use
Rev 1.05 as of 2012-04-11 Trenz Electronic GmbH info@trenz-electronic.de www.trenz-electronic.de Prototyg Carrier Board for Industrial Micromodule Overview The Prototyg Carrier Board provides low-cost
More informationTAP CONNECT JTAG CABLE
TAP CONNECT JTAG Cable Application Notes TAP CONNECT JTAG CABLE ontap JTAG Test & Programming Cable Installation and Setup Instructions for Standard and Low Voltage Cable Rev. V Table of Contents About
More informationIntroducing AVR Dragon
Introducing AVR Dragon ' Front Side Back Side With the AVR Dragon, Atmel has set a new standard for low cost development tools. AVR Dragon supports all programming modes for the Atmel AVR device family.
More informationIntroduction. Getting familiar with chipkit Pi
Overview: chipkit Pi Introduction chipkit Pi (Designed for Raspberry Pi) is the latest Arduino compatible chipkit platform from Microchip and element14. It features a 32 bit PIC32 microcontroller in a
More informationRC2200DK Demonstration Kit User Manual
Demonstration Kit User Manual Table of contents TABLE OF CONTENTS... 1 QUICK INTRODUCTION... 2 INTRODUCTION... 3 DEMONSTRATION BOARD... 4 POWER SUPPLY SECTION... 5 RS-232 INTERFACE... 6 CONNECTORS... 7
More informationApplication Note, V2.2.1, July 2003 AP24001. OCDS Level 1 JTAG Connector. 16-Bit & 32-Bit Microcontrollers. AI Microcontrollers. Never stop thinking.
Application Note, V2.2., July 2003 AP2400 OCDS Level JTAG Connector 6-Bit & 32-Bit Microcontrollers AI Microcontrollers Never stop thinking. OCDS Level JTAG Connector Revision History: 2003-07 V2.2. Previous
More informationISP Engineering Kit Model 300
TM ISP Engineering Kit Model 300 December 2013 Model 300 Overview The Model 300 programmer supports JTAG programming of all Lattice devices that feature non-volatile configuration elements. The Model 300
More informationAMC13 T1 Rev 2 Preliminary Design Review. E. Hazen Boston University. 2012-10-30 E. Hazen - AMC13 T1 V2 1
13 T1 Rev 2 Preliminary Design Review E. Hazen Boston University 2012-10-30 E. Hazen - 13 T1 V2 1 Scope of this Review Background: 13 T1 board is being revised to support 10 GbE per request from CDAQ group
More informationFigure 1. 8-Bit USB Debug Adapter
8-BIT USB DEBUG ADAPTER USER S GUIDE 1. Introduction The 8-bit USB Debug Adapter (UDA) provides the interface between the PC s USB port and the Silicon Labs 8-bit target device s in-system debug/programming
More informationUSB - FPGA MODULE (PRELIMINARY)
DLP-HS-FPGA LEAD-FREE USB - FPGA MODULE (PRELIMINARY) APPLICATIONS: - Rapid Prototyping - Educational Tool - Industrial / Process Control - Data Acquisition / Processing - Embedded Processor FEATURES:
More informationThe following is a summary of the key features of the ARM Injector:
Intended Use The ARM Injector is an indispensable tool for engineers who work with JTAG enabled target systems based on an ARM processor core with Debug and EmbeddedICE capability. The ARM Injector provides
More informationOpen Flow Controller and Switch Datasheet
Open Flow Controller and Switch Datasheet California State University Chico Alan Braithwaite Spring 2013 Block Diagram Figure 1. High Level Block Diagram The project will consist of a network development
More informationEMUL ARM. ARM Connections. 2003 Nohau Corporation. All rights reserved worldwide.
EMUL ARM ARM Connections 2003 Nohau Corporation. All rights reserved worldwide. Nohau By ICE Technology EMUL-ARM: ARM Connections 2 (8) Contents 1 INTRODUCTION... 3 2 CONNECTIONS... 4 20-Pin JTAG Connection
More informationUSB-Blaster Download Cable User Guide
USB-Blaster Download Cable User Guide Subscribe UG-USB81204 101 Innovation Drive San Jose, CA 95134 www.altera.com TOC-2 Contents Introduction to USB-Blaster Download Cable...1-1 USB-Blaster Revision...1-1
More informationJTAG-HS2 Programming Cable for Xilinx FPGAs. Overview. Revised January 22, 2015 This manual applies to the HTAG-HS2 rev. A
1300 Henley Court Pullman, WA 99163 509.334.6306 www.digilentinc.com Programming Cable for Xilinx FPGAs Revised January 22, 2015 This manual applies to the HTAG-HS2 rev. A Overview The Joint Test Action
More informationMasterBlaster Serial/USB Communications Cable User Guide
MasterBlaster Serial/USB Communications Cable User Guide 101 Innovation Drive San Jose, CA 95134 www.altera.com Software Version: 80 Document Version: 1.1 Document Date: July 2008 Copyright 2008 Altera
More informationName Description Model Number. Parameters Min. Typ. Max. Note. Vaux Voltage 9.8 V 12 V 13.2 V Auxiliary Supply Voltage
Description Supports DALI interface driver Programming Supports 0-10V Programmable Driver Programming Supports Other Controllers (TDD-ANPNx, SDD-AAPNx) Off-line programming capability Auto programming
More informationAPPLICATION NOTE. Atmel AVR2033: SAM-ICE Adapter Hardware User Manual. 8-bit Atmel Microcontrollers. Features. Introduction
APPLICATION NOTE Features Atmel AVR2033: SAM-ICE Adapter Hardware User Manual 8-bit Atmel Microcontrollers 10-pin connector for Atmel RF231USB USB radio stick 20-pin connector for ARM JTAG programmer 6-pin
More informationXBee USB Adapter Board (#32400)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationUM1075 User manual. ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32. Introduction
User manual ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 Introduction The ST-LINK/V2 is an in-circuit debugger/programmer for the STM8 and STM32 microcontroller families. The single wire
More informationIDE to SATA HDD Adapter Quick Installation Guide
IDE to SATA HDD Adapter Quick Installation Guide Introducing the IDE to SATA HDD Adapter The IDE to SATA HDD Adapter allows you to connect a newer Serial ATA hard drive to older IDE/UltraATA host adapters.
More informationDKWF121 WF121-A 802.11 B/G/N MODULE EVALUATION BOARD
DKWF121 WF121-A 802.11 B/G/N MODULE EVALUATION BOARD PRELIMINARY DATA SHEET Wednesday, 16 May 2012 Version 0.5 Copyright 2000-2012 Bluegiga Technologies All rights reserved. Bluegiga Technologies assumes
More informationDAP miniwiggler V3. Application Note. Microcontrollers AP56004 V1.0 2013-07
DAP miniwiggler V3 Application Note V1.0 2013-07 Microcontrollers Edition 2013-07 Published by Infineon Technologies AG 81726 Munich, Germany 2013 Infineon Technologies AG All Rights Reserved. LEGAL DISCLAIMER
More informationAPPLICATION NOTE. Atmel AVR600: STK600 Expansion, Routing and Socket Boards. Atmel Microcontrollers. Introduction
APPLICATION NOTE Atmel AVR600: STK600 Expansion, Routing and Socket Boards Introduction Atmel Microcontrollers This application note describes the process of developing new routing, socket and expansion
More informationWelcome to Pericom s PCIe and USB3 ReDriver/Repeater Product Training Module.
Welcome to Pericom s PCIe and USB3 ReDriver/Repeater Product Training Module. 1 Pericom has been a leader in providing Signal Integrity Solutions since 2005, with over 60 million units shipped Platforms
More informationHardware User Guide 2.1i
Hardware User Guide Cable Hardware MultiLINX Cable FPGA Design Demonstration Board CPLD Design Demonstration Board Hardware User Guide.i Printed in U.S.A. Hardware User Guide R The Xilinx logo shown above
More informationAppendix A: Camera connectors
Appendix A: Camera connectors USB: Standard Type A (provides power) and Type B (consumes power) USB 2.0 connectors + and terminals provide 5V @ 500mA and ground respectively for USB2.0 and up to 2A for
More informationKey features: About this backplane:
Key features: Topology: Full Mesh VPX Backplane compliant to the VITA 46.0 core specification Backplane is supporting subsidiary specifications for protocols as: Serial Rapid IO (VITA 46.3), PCI Express
More information+Denotes lead-free and RoHS-compliant. C5 C10, C17, C18
19-0623; Rev 1; 3/08 Maxim MINIQUSB User Guide General Description The Maxim command module (MINIQUSB) receives commands from a PC through the USB to create an SPI or SMBus /I 2 C-compatible interface.
More informationDATENBLATT USB-DIO32HS USB-DIO32HS-OEM. HABEN SIE FRAGEN ODER WÜNSCHEN SIE EIN INDIVIDUELLES ANGEBOT? Unser Team berät Sie gerne persönlich.
DATENBLATT USB-DIO32HS HABEN SIE FRAGEN ODER WÜNSCHEN SIE EIN INDIVIDUELLES ANGEBOT? Unser Team berät Sie gerne persönlich. TELEFON + 49 (0) 81 41/36 97-0 TELEFAX + 49 (0) 81 41/36 97-30 E-MAIL info@plug-in.de
More informationALL-USB-RS422/485. User Manual. USB to Serial Converter RS422/485. ALLNET GmbH Computersysteme 2015 - Alle Rechte vorbehalten
ALL-USB-RS422/485 USB to Serial Converter RS422/485 User Manual ALL-USB-RS422/485 USB to RS-422/485 Plugin Adapter This mini ALL-USB-RS422/485 is a surge and static protected USB to RS-422/485 Plugin Adapter.
More informationAdvanced Data Capture and Control Systems
Advanced Data Capture and Control Systems Tronisoft Limited Email: sales@tronisoft.com Web: www.tronisoft.com RS232 To 3.3V TTL User Guide RS232 to 3.3V TTL Signal Converter Modules P/N: 9651 Document
More informationUIM2901-5A MACH3 breakout board
User Manual UIM2901-5A MACH3 Breakout Board UIM2901-5A MACH3 Breakout Board UIM2901-5A MACH3 breakout board Features General DB25 interface between PC and user device Fully buffered opto-isolated I/O (Input
More informationThe Advanced JTAG Bridge. Nathan Yawn nathan.yawn@opencores.org 05/12/09
The Advanced JTAG Bridge Nathan Yawn nathan.yawn@opencores.org 05/12/09 Copyright (C) 2008-2009 Nathan Yawn Permission is granted to copy, distribute and/or modify this document under the terms of the
More informationSPI Flash Programming and Hardware Interfacing Using ispvm System
March 2005 Introduction Technical Note TN1081 SRAM-based FPGA devices are volatile and require reconfiguration after power cycles. This requires external configuration data to be held in a non-volatile
More informationMassachusetts Institute of Technology Department of Electrical Engineering and Computer Science 6.115 Microprocessor Project Laboratory
Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science 6.115 Microprocessor Project Laboratory Connecting your PSoC Evaluation Board It is easy and fun to avoid
More informationWinLIN Setup and Operation:
Frequently Asked Questions about the 07551-Series Masterflex L/S Computer-Compatible drives and about the Masterflex WinLIN Linkable Instrument Control Software (07551-70) WinLIN Setup and Operation: Will
More informationSSI-USB. Flexible Embedded Platform. Brief English Version
SSI-USB Brief English Version Seite 1/6 SSI-USB Flexible Embedded Platform Brief English Version Hardware v1.0 Dokument: 1401171103 SSI-USB Brief English Version Seite 2/6 1 Preface The SSI-USB-module
More informationDMX-K-DRV. Integrated Step Motor Driver + (Basic Controller) Manual
DMX-K-DRV Integrated Step Motor Driver + (Basic Controller) Manual DMX-K-DRV Manual page 1 rev 1.33 COPYRIGHT 2007 ARCUS, ALL RIGHTS RESERVED First edition, June 2007 ARCUS TECHNOLOGY copyrights this document.
More informationName Description P/N. Programmer Programmer with calibration function SDD-AAPNP. Parameter Min. Typ. Max. Notes. (Vo+ - Vo-) - Voltage
Description SDD-AAPNP is the programmer for non-dali Inventronics drivers, and the programmer and calibrator for the following intelligent controllers: SDD-AAPNx Dimming Signal Attenuator TDD-ANPNx Combo
More informationrevolution Contents: Introduction Power 28-pin Project Board with input/output cables
28-PIN IN IN PROJECT BOARD Contents: AXE020 28-pin Project Board with input/output cables Introduction The 28-pin project board is designed to allow rapid prototyping with 28-pin PICAXE microcontrollers.
More informationJTAG Applications. Product Life-Cycle Support. Software Debug. Integration & Test. Figure 1. Product Life Cycle Support
JTAG Applications While it is obvious that JTAG based testing can be used in the production phase of a product, new developments and applications of the IEEE-1149.1 standard have enabled the use of JTAG
More informationBrightSign Expander Hardware Guide
Hardware Guide PCBA: Rev C Version: 0.1 Saratoga, CA, USA 1 Table of Contents OVERVIEW... 3 EXPANDER BLOCK DIAGRAM... 4 PORTS... 6 POWER CONNECTOR... 6 OPTICAL SPDIF CONNECTOR... 6 DB25 SWITCH/LED CONNECTOR...
More informationUM1075 User manual. ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32. Introduction
User manual ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 Introduction The ST-LINK/V2 is an in-circuit debugger/programmer for the STM8 and STM32 microcontroller families. The single wire
More informationHPUSB, USB, HPPCI and MSP430 Emulators Users Guide
HPUSB, USB, HPPCI and MSP430 Emulators Users Guide Revision 3.0, December 2007 Part Number 82-000760-01 Analog Devices, Inc. One Technology Way Norwood, Mass. 02062-9106 a Copyright Information 2007 Analog
More informationC232HM. USB 2.0 Hi-Speed to MPSSE Cable. Datasheet
Future Technology Devices International Ltd C232HM USB 2.0 Hi-Speed to MPSSE Cable Datasheet Document Reference No.: FT_000401 Issue Date: 2016-05-05 Future Technology Devices International Limited (FTDI)
More information_ v1.0. EVB-56x Evaluation & Development Kit for Motorola PowerPC MPC56x Microcontrollers USERS MANUAL. isystem, February 2003 1/8.
_ v1.0 USERS MANUAL EVB-56x Evaluation & Development Kit for Motorola PowerPC MPC56x Microcontrollers EVB-563 EVB-565 Ordering code ITMPC563 ITMPC565 Copyright 2003 isystem, GmbH. All rights reserved.
More informationUSB PC Adapter V4 Configuration
Programming PC adapter V4 USB PC Adapter V4 Configuration PC adapter with USB cable Flat Ribbon Cable Power Supply Unit Device Driver General The USB PC adapter V4 is used for communication between a PC
More informationQuick Start Guide for High Voltage Solar Inverter DC-AC Board EVM. Version 1.3
Quick Start Guide for High Voltage Solar Inverter DC-AC Board EVM Version 1.3 Introduction This document talks about the quick start principles for the high voltage solar inverter DC-AC board. From this
More informationCommunication with BushingGard using computer USB port
Communication with BushingGard using computer USB port There are two ways of communication with BushingGard through computer USB port: Direct communication between computer USB port and BushingGard USB
More informationTS2 VRack. User and Installation Manual
TS2 VRack User and Installation Manual B 4934252 Rev. A October 2007 TS-2 VRack All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical,
More informationic-mq EVAL MQ1D EVALUATION BOARD DESCRIPTION
Rev A3, Page 1/7 ORDERING INFORMATION Type Order Designation Description and Options Evaluation Board ic-mq EVAL MQ1D ic-mq Evaluation Board ready to operate, accessible through GUI via PC adapter Software
More informationLab 1: Introduction to Xilinx ISE Tutorial
Lab 1: Introduction to Xilinx ISE Tutorial This tutorial will introduce the reader to the Xilinx ISE software. Stepby-step instructions will be given to guide the reader through generating a project, creating
More informationUsing ispgdx, isplsi 2000VE and 5000V Devices in Hot-Swap Environments
TM Using ispgdx, isplsi 2000VE and 5000V Devices in Hot-Swap Environments Introduction This document describes the input and I/O characteristics of Lattice ispgdx, ispgdxv, isplsi 2000VE and 5000V devices
More informationLiveDesign Evaluation Board Technical Reference Manual. Technical reference manual for Altium s LiveDesign Evaluation Boards
LiveDesign Evaluation Board Technical Reference Manual Technical reference manual for Altium s LiveDesign Evaluation Boards CAUTION THIS EQUIPMENT INCLUDES EXPOSED ELECTRONIC COMPONENTS THAT ARE HIGHLY
More informationCP2110-EK CP2110 EVALUATION KIT USER S GUIDE. 1. Kit Contents. 2. Relevant Documentation. 3. Software Setup
CP2110 EVALUATION KIT USER S GUIDE 1. Kit Contents The CP2110 Evaluation Kit contains the following items: CP2110 Evaluation Board RS232 Serial Cable USB Cable DVD Quick Start Guide 2. Relevant Documentation
More informationDU-H3ETX. 3-port USB Hub with 1 NWAY Ethernet / Fast Ethernet Port. User s Guide
DU-H3ETX 3-port USB Hub with 1 NWAY Ethernet / Fast Ethernet Port User s Guide 1 Table of Contents INTRODUCTION...1 TECHNOLOGY OVERVIEW... 1 ABOUT DU-H3ETX... 2 PRODUCT FEATURES... 3 INSTALLATION...4 ASPECT
More informationEvo Laser Firmware Developer s Manual
Evo Laser Firmware Developer s Manual Table of Content Chapter 1 Introduction Chapter 2 Hardware Overview and Subsystems 2.1 Overview 2.2 Evo Laser Hardware Core System 2.3 Evo Laser Smartport TM Chapter
More informationThe modular concept of the MPA-3 system is designed to enable easy accommodation to a huge variety of experimental requirements.
HARDWARE DESCRIPTION The modular concept of the MPA-3 system is designed to enable easy accommodation to a huge variety of experimental requirements. BASE MODULE GO LINE Digital I/O 8 Analog Out AUX 1
More informationRS-232 COMMUNICATIONS
Technical Note D64 0815 RS-232 COMMUNICATIONS RS-232 is an Electronics Industries Association (EIA) standard designed to aid in connecting equipment together for serial communications. The standard specifies
More informationInstallation Instructions for 9555 USB Driver
Prior to using the data modem features of your 9555 handset; you must first install the VCOMPORT 9555 USB Driver. This driver is compatible with: Windows XP Service Pack 2, Windows 2000 Service Pack 4,
More informationSuperSpeed USB Host: Jeff Ravencraft, USB-IF president and chairman
SuperSpeed USB Host: Jeff Ravencraft, USB-IF president and chairman Agenda Introduction & technology overview Jeff Ravencraft Microsoft Corporation Fred Bhesania NEC Electronics Corporation Yoshiyuki Tomoda
More information2013 CNS Geiger Kit Instructions read me Page 1 of 5
2013 CNS Geiger Kit Instructions read me Page 1 of 5 We re pleased to inform you that Aware Electronics have provided the CNS with a custom version of their Aw-Radw software 8.4a. There are two new versions:
More informationInstallation Guide for RadioLabs USB Wifi Antennas/Adapters
1 Installation Guide for RadioLabs USB Wifi Antennas/Adapters 2 PLEASE READ BEFORE ATTEMPTING INSTALLATION Thank you for purchasing a RadioLabs USB wireless networking product. This document will guide
More informationSpW-10X Network Performance Testing. Peter Mendham, Jon Bowyer, Stuart Mills, Steve Parkes. Space Technology Centre University of Dundee
SpW-0X Network Performance Testing Peter Mendham, Jon Bowyer, Stuart Mills, Steve Parkes Space Technology Centre University of Dundee Before I Start... POR configuration of 0X Sets defaults for each port
More informationHC(S)08-System for Development and Training
SYSTECH J.Schnyder GmbH Schliefweg 30 CH-4106 Therwil Telefon 091 827 15 87 www.systech.ch HC(S)08-System for Development and Training Overview V 0.3 (Draft English) Contents Components... 3 Hardware...
More informationWorkshop Intel Galileo Board
Workshop Intel Galileo Board Introduction and Basics of Intel Galileo Board Walter Netto November 03th, 2014 Agenda Intel Galileo Board Overview Physical Characteristics Communication Processor Features
More informationUSB 3.0 to VGA External Multi Monitor Graphics Adapter with 3-Port USB Hub VGA and USB 3.0 Mini Dock 1920x1200 / 1080p
USB 3.0 to VGA External Multi Monitor Graphics Adapter with 3-Port USB Hub VGA and USB 3.0 Mini Dock 1920x1200 / 1080p StarTech ID: USB32VGAEH3 The USB32VGAEH3 USB 3.0 to VGA Adapter turns a USB 3.0 port
More informationPCM over USB sample rates 44.1Khz 48Khz, 88,2Khz,96Khz,192Khz 352.8Khz, 384Khz I2S output
FEATURES Core ARM Cortex -M3 ATSAM3U CPLD XILINX XC2C64A OSCILLATORS TCXO 24.5760 Mhz Low phase noise TCXO 22.5792 Mhz Low phase noise USB USB 2.0 High Speed dedicated 12Mhz crystal Class 2 compatible
More informationIndustrial Bar Code Scanners
DX8200A Industrial Bar Code Scanners Configuration SW Tool ACR4 technology PackTrack ASTRA technology APPLICATIONS Postal/Courier parcel sorting and tracking Automated warehousing identification systems
More informationExpress11-G3 Backplane. User Guide. Version: 1.02
Express11-G3 Backplane User Guide Version: 1.02 Unpacking Your packing box should contain the following items: The Express11-G3 Backplane SLink-G3 Card (optional) HLink-G3 Card (optional) ExCable-G3 (optional)
More informationSIMPLE EPROM PROGRAMMER. EPROM Programmer Design. Hardware
Page 1 of 5 A simple EPROM programmer is described here. It connects to a PC's parallel port and can program EPROMs from 2716 to 27512. The design can be expanded to program even larger EPROMs. DOS based
More informationUSB-Blaster Download Cable User Guide
USB-Blaster Download Cable User Guide 101 Innovation Drive San Jose, CA 95134 www.altera.com Software Version: 9.0 Document Version: 2.5 Document Date: April 2009 UG-USB81204-2.5 P25-10325-03 Copyright
More informationSTM-P103 development board user's manual
STM-P103 development board user's manual Rev.B, September 2013 Copyright(c) 2013, OLIMEX Ltd, Some rights reserved INTRODUCTION: STM32-P103 board is development board which allow exploring the complete
More informationDOEPFER MIDI TO SYNC INTERFACE MSY2. User's Guide (English)
DOEPFER MIDI TO SYNC INTERFACE MSY2 User's Guide (English) www.doepfer.com INTRODUCTION MSY2 is an interface that converts the MIDI realtime events CLOCK, START and STOP into the corresponding signals
More informationSERVO CONNECTIONS FOR OLDER BOARDS
What s a Microcontroller v3.0 Suppliment to Chapter 7, Activity #1 SERVO CONNECTIONS FOR OLDER BOARDS This document explains how to connect servo and LED indicator circuits to the older revisions of the
More informationBitBlaster Serial Download Cable
BitBlaster Serial Download Cable February 2002, ver. 4.3 Data Sheet Features Allows PC and UNIX workstation users to perform the following functions: Program MAX 9000, MAX 7000S, MAX 7000A, and MAX 3000A
More informationCMOS OV7660 Camera Module 1/5-Inch 0.3-Megapixel Module Datasheet
CMOS OV7660 Camera Module 1/5-Inch 0.3-Megapixel Module Datasheet Rev 1.0, June 2013 Table of Contents 1 Introduction...2 2 Features...3 3 Key Specifications...4 4 Application...4 5 Pin Definition...6
More informationUSB 3.0 to HDMI External Multi Monitor Graphics Adapter with 3-Port USB Hub HDMI and USB 3.0 Mini Dock 1920x1200 / 1080p
USB 3.0 to HDMI External Multi Monitor Graphics Adapter with 3-Port USB Hub HDMI and USB 3.0 Mini Dock 1920x1200 / 1080p StarTech ID: USB32HDEH3 The USB32HDEH3 USB 3.0 to HDMI Adapter turns a USB 3.0 port
More informationSolutions for Increasing the Number of PC Parallel Port Control and Selecting Lines
Solutions for Increasing the Number of PC Parallel Port Control and Selecting Lines Mircea Popa Abstract: The paper approaches the problem of control and selecting possibilities offered by the PC parallel
More informationIn-System Programming Design TM. Guidelines for ispjtag Devices. Introduction. Device-specific Connections. isplsi 1000EA Family.
In-System Design TM February 2002 Introduction In-system programming (ISP ) has often been billed as a direct replacement for configuring a device through a programmer. The idea that devices can simply
More informationUSA MOBILITY CABLE CONNECTION AND SOFTWARE DRIVER INSTALLATION INSTRUCTIONS. For. Unication M90 Device USB To RS232 Adapter TABLE OF CONTENTS
USA MOBILITY CABLE CONNECTION AND SOFTWARE DRIVER INSTALLATION INSTRUCTIONS For Unication M90 Device USB To RS232 Adapter TABLE OF CONTENTS SECTION 1: ADAPTER CABLE CONNECTION INSTRUCTIONS... 2 SECTION
More informationConvenient Accessibility
Conference Table Connectivity Box HDMI / VGA / Mini DisplayPort to HDMI Output with Fast Charge USB Port StarTech ID: BOX4HDECP The BOX4HDECP Automatic Conference Table Connectivity Box features a concealed,
More informationECP240-32 & ECP240-32EX
ECP240-32 & ECP240-32EX Hardware Manual 11Fl., 684-2, Deungchon 3-Dong, Gangseo-Gu, Seoul, Korea TEL: +82 2 2605 1486 FAX: +82 2 2605 1489 http://www.udptech.co.kr Contents 1. PRODUCT OVERVIEW...1 1.1
More information56F8300 Demonstration Board
56F8300 Demonstration Board User Manual 56F800 16-bit Digital Signal Controllers MC56F8300DBUM Rev. 4 08/2005 freescale.com Table of Contents Preface ix Audience........................................................
More informationMESA ELECTRONICS PRICE LIST 9/15/15
PC/104 CARDS: 4A23 20 bit delta-sigma isolated input A-D 257 206 195 186 4A24-2 High speed 16 bit A-D 200KHz 257 206 195 186 4A24-5 High speed 16 bit A-D 500KHz 314 251 239 227 4I20 24 output 48V/350 ma
More informationGraphics Card I/O Ports and Interfaces
Graphics Card I/O Ports and Interfaces Graphics cards today are responsible for much more than simple text output to monitor. Their duties now include heavy-duty 2D and 3D rendering as well as video processing.
More informationDOSISYS. Hands Free Reader LDM 210 - LDM 220. User Manual 127356A
DOSISYS LDM 210 - LDM 220 Hands Free Reader User Manual 127356A Publication, translation and reproduction total or partial of this document is strictly forbidden without authorization MGP Instruments
More informationRCC2 Test Proceedures
RCC2 Test Proceedures 1. Power-up Test 1. install board in VME crate (6U style or 6U section of 9U) and turn on power 2. check that cfg LED (D4) on front panel and D3 LED on board near U47 are lit (red)
More informationDriver Pant 8 and antenna switcher Ant 8. User manual
Driver Pant 8 and antenna switcher Ant 8 User manual Table of contents Table of contents... 2 Introduction... 3 Shipping Contents... 3 Technical Data... 3 Control Panel... 4 Rear panel... 5 Controller
More informationCalDigit SuperSpeed PCI Express Card
CalDigit SuperSpeed PCI Express Card For more information visit www.caldigit.com Fast, Reliable and Secure Storage Solutions Apple, Apple Logo, Mac, the Mac logo and Macintosh are trademarks of Apple Inc.
More informationGetting Started with the Xilinx Zynq- 7000 All Programmable SoC Mini-ITX Development Kit
Getting Started with the Xilinx Zynq- 7000 All Programmable SoC Mini-ITX Development Kit Table of Contents ABOUT THIS GUIDE... 3 ADDITIONAL DOCUMENTATION... 3 ADDITIONAL SUPPORT RESOURCES... 3 INTRODUCTION...
More informationUSB 2.0 Bay Media Card Reader Quick Installation Guide
USB 2.0 Bay Media Card Reader Quick Installation Guide Introducing the Media Card Reader The USB 2.0 Bay Media Card Reader is the perfect choice for computer users looking for a flash memory card reader
More informationHow To Use An Ams 5812 Pressure Sensor With A Usb Starter Kit
User Guide USB Starter Kit AMS 5812 Phone:+49 (0)6131/91 0730-0 Fax: +49 (0)6131/91 073-30 Internet: E Mail: info@analogmicro.de Analog Microelectronics GmbH An der Fahrt 13, D 55124 Mainz May 2012 - Rev.
More informationApplication Note: Connecting to a 2500 Series Processor using PLC Workshop
Application Note: Connecting to a 2500 Series Processor using PLC Workshop This application note will describe a step by step process for the three ways to connect to a 2500-CXXX with PLC Workshop. The
More informationPCAN-ISA. CAN Interface for ISA. User Manual
PCAN-ISA CAN Interface for ISA User Manual Products taken into account Product Name Model Item Number PCAN-ISA Single Channel One CAN channel IPEH-002074 PCAN-ISA Dual Channel Two CAN channels IPEH-002075
More informationxpico Wi-Fi Embedded Device Server Evaluation Kit Quick Start Guide
xpico Wi-Fi Embedded Device Server Evaluation Kit Quick Start Guide Part Number 900-685 Revision A June 2013 Copyright and Trademark Contacts 2013 Lantronix, Inc.. All rights reserved. No part of the contents
More informationHardware Manual CAN-IB130/PCIe CAN-IB230/PCIe PCIe/104 CAN Interface
Hardware Manual CAN-IB130/PCIe CAN-IB230/PCIe PCIe/104 CAN Interface The expert for industrial and automotive communication IXXAT Headquarter US Sales Office IXXAT Automation GmbH IXXAT Inc. Leibnizstr.
More informationQUICK INSTALLATION. MSX-E1516 Ethernet digital I/O system 02.04-08/2014
QUICK INSTALLATION MSX-E1516 Ethernet digital I/O system 02.04-08/2014 Addi-data GmbH Airpark Business Center Airport Boulevard B210 77836 Rheinmünster Germany Tel: +49 7229 1847-0 Fax: +49 7229 1847-200
More informationHVP-KV31F120M Quick Start Guide
HVP-KV31F120M Quick Start Guide Freescale Controller Card High Voltage Development Platform Quick Start Guide Get to Know the HVP-KV31F120M USB Mini for Communication, Debugging and Power Supply Isolated
More information