Vickers. Service Data. Vane Pumps. Vane Type Triple Pump (F3) 4535VQSV10* ***** ******* 20* Released M 2497 S
|
|
- Arthur Parsons
- 7 years ago
- Views:
Transcription
1 Service Data Vickers Vane Pumps Vane Type Triple Pump (F3) 4535VQSV10* ***** ******* 20* Released M 2497 S
2 10 SAE rated capacity (V10 cover end cartridge) USgpm Rotor Vane Kit Ring Pin Pin Bolt Bolt Bolt Cartridge Kit (12 vanes) (V10S) (V10F/V10P) (V10S) (V10F) (V10P) V10P Cover Option Bolt (4 Req d) Torque N.m. (35 45 lb. ft.) 2706 Seat Poppet Spring Shim Kit O Ring Plug V10S Cover Option Plug Spring Piston Plug Spring O Ring Bolt (4 Req d) Torque N.m. (35 45 lb. ft.) O Ring Wear plate O Ring Pin (2 Req d) Ring Vane Kit 9 V10 port connection V10S Cover V10F Cover V10P Cover P R S Y T K Rotor Pressure Plate S/A Plug Spring Control Valve S/A V10F Cover Option Ring Plug Bolt (4 Req d) Torque N.m. (35 45 lb. ft.) 17 Pressure setting V10P/V10F (Omit for V10S) A B C D E F G H J K Pressure setting V10P/V10F 250 psi 500 psi 750 psi 1000 psi 1250 psi 1500 psi 1750 psi 2000 psi 2250 psi 2500 psi V10P Spring V10F control valve S/A
3 Flex Side Plate Kit Rotor Flex Side Plate Kit Outlet Plate O Ring Seal Ring O Ring B.U. Ring Rear Mounting Cover Bolt (4 Req d) Torque N.m. ( lb. ft.) Inlet Cover Screw (2 Req d) Torque 11 N.m. (100 lb. in.) Pin (2 Req d) Inlet Plate Seal Pack (4 Req d) Ring Vane Kit (Includes 10 Vanes & inserts) Seal Pack (4 Req d) 8 SAE rated capacity (**35 VQ center cartridge) USgpm Ring Inlet Plate Rotor Vane Kit F3 Cart. Kit Included in 45** VQ shaft end cartridge kit. Included in **35 VQ center cartridge kit. Included in V10 cover end cartridge kit. Included in seal kit (Kit contains F3 components & both shaft seals.) Included in flex side plate kit; bronze face of plate must be installed toward the rotor. Kit also contains four seal packs. Assemble seal with spring loaded sealing member towards bearing. Seals to be completely wetted with oil prior to assembly. Install & sealing ring into body, then install cartridge kit.
4 Seal Ring O Ring Outlet Plate Seal Pack (4 Req d) Flex Side Plate Kit Ring Rotor Flex Side Plate Kit Seal Pack (4 Req d) inlet Plate Pin (2 Req d) Screw (2 Req d) Torque 11 N.m. (100 lb.in.) Primary Shaft Seal Washer Shaft (297 Type) Lockring Vane Kit (Includes 10 Vanes & Inserts) Body Kit Secondary Shaft Seal Bearing Ring B.U. Ring O Ring 6 SAE rated capacity (45**VQ shaft end cartridge) USgpm Ring F3 Cart. Kit Port connections Connection Type Body Kit Inlet Cover Rear Mounting Cover A 4 Bolt Flange (Inch) AM 4 Bolt Flange (Metric) NOTE: Body kit includes body, ball, and plug. (Ball and plug not shown.)
5 Model Special seals F3 Vition O Rings and shaft seals 2 Pump series designation 45**VQ Shaft end pump **35VQ Center pump 3 Body mounting flange S SAE mounting per J Pump series designation V10 cover end pump 5 V10 pump cover options S Standard cover F Flow control and relief cover P Priority valve and relief cover 6 SAE rated capacity (VQ shaft end cartridge) USgpm USgpm USgpm 7 VQ port connections (inlet & outlet #1 & #2) A 4 bolt flange (inch threads) AM 4 bolt flange (metric threads) USgpm USgpm 9 V10 port connections V10S standard covers and outlet # 3 S Str. thd. P 1 / 2 NPT thd. Y Str. thd. R Str. thd. V10F flow/relief control cover Outlet # 3 T Str. thd P Str. thd. V10P priority control covers Primary port Str. thd Secondary port Str. thd. 10 SAE rated capacity (V10 cover end cartridge) 1 1 USgpm 2 2 USgpm 3 3 USgpm 4 4 USgpm Shaft seal Blank Single seal S Double seal Tank port Str. thd. 1 / 2 NPT thd. Tank port Str. thd K USgpm 6 6 USgpm 7 7 USgpm Port orientation (Outlet #2) (Viewed from cover end of pump; refer to table on next page) Port orientation (Outlet #3 or primary outlet) (Viewed from cover end of pump; refer to table on next page) Controlled flow rate, V10F & V10P (Omit for standard cover) 3 3 USgpm 4 4 USgpm 5 5 USgpm Design (Subject to change) 6 6 USgpm 7 7 USgpm 8 8 USgpm 17 Relief valve pressure setting, V10F & V10P (Omit for standard cover) A 250 psi B 500 psi C 750 psi D 1000 psi E 1250 psi 18 F 1500 psi G 1750 psi H 2000 psi J 2250 psi K 2500 psi 19 Rotation (Viewed from shaft end of pump) L Left hand for counterclockwise R Right hand for clockwise 8 SAE rated capacity (VQ center cartridge) 12 Shaft type 297 All series USgpm USgpm USgpm USgpm USgpm 13 Port orientation (Outlet #1) (Viewed from cover end of pump; refer to table on next page)
6 15 Outlet #3 ( or primary outlet) 13 Outlet #1 14 Outlet #2 (at C position) (at C position) 14 Outlet #2 Inlet 13 Outlet #1 15 Outlet #3 (at C position) Outlet Opposite inlet 90 CCW from inlet Inline with inlet 90 CW from inlet Port orientation code (Viewed from cover end of pump) 13 #1 14 #2 15 #3 A A A B B B C C C D D D Position view only NOTE V10 cover can be assembled in any of four positions refer to drawing M 2005 S. Sharp Edges of Vane Must Lead in Direction of Rotation NOTE To reverse cartridge kit rotation, remove the two screws and reverse the location of the inlet support plate and the outlet support plate. Reinstall the two screws hand tight. Use pump cover to align all sections of the cartridge. Carefully remove the cover and tighten the screws. Cover End Cartridge R. H. Rotation Shaft End Cartridge R. H. Rotation NOTE Standard right hand shaft rotation cartridges shown. Reverse for left hand rotation. When ordering spare cartridge parts, it is recommended they be obtained in cartridge kits. Kits are assembled and tested for either right or left hand rotation. If left hand rotation is required, it should be specified on parts order by adding suffix L to cartridge kit number.
VHO/VQ Single, Double & Triple Vane Pumps
VHO/VQ Single, Double & Triple Vane Pumps Series Available: 20, 25, 30, 35, 45, 50 For Mobile and Industrial Use Cartridge Kits Available for All Sizes Same Day Shipments www.fluidynefp.com Our People
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationPVQ 40-B2/M2 * *** - ** * * - 10 C** *** *** * - 10/11/12/20 PVQ 45-B2/M2 * *** - ** * * - 10 C**
Service Data Vickers Piston Pumps Low Noise Industrial Piston Pump PVQ 40-B2/M2 * *** - ** * * - 10 C** *** *** * - 10/11/12/20 PVQ 45-B2/M2 * *** - ** * * - 10 C** *** *** * - 10/11/12/20 C, CM Compensator
More informationPVH131/141 Variable Displacement Piston Pump - 11 Design
Service Data Vickers Piston Pumps PVH131/141 Variable Displacement Piston Pump - 11 Design Revised 05/01/97 M-2209-S Maximum Adjustable Stop S Option 913341 Locknut Torque 25-50 N.m. (18-37 lb. ft.) Torque
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationVickers. Check Valves. Check Valves. Inline, right angle, manifold mounted, and pilot operated designs. Released 9/93
Vickers Check Valves Check Valves Inline, right angle, manifold mounted, and pilot operated designs Released 9/93 645 Introduction Vickers inline, right-angle, and manifold mounted check valves are direct
More informationPVM Piston Pumps Service Manual
PVM Piston Pumps Service Manual PVM018/020 PVM045/050 PVM057/063 PVM074/081 PVM098/106 PVM131/141 Table of Contents Service Parts Pump Description... 3 Basic pump Pump Operation Controls Types Part Identification...
More informationHydraulic Pump/Motor Division Hydraulic Pump/Motor Division
Parker Piston Pumps Otsego Core Competency... Piston Pumps PAVC Series : 4 displacements from 33-100 cc/r, 207 Bar, 3000 RPM PVP Series : 9 displacements from 16-140 cc/r, 250 Bar, 3000 RPM PV Plus : 12
More informationTable of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19
Table of Contents Overview 1 Pump Disassembly 2 Control Disassembly / Reassembly 7 Pump Reassembly 13 Adjustment Procedures DR Control 19 Adjustment Procedures DRG Control 20 Adjustment Procedures DFR
More informationChar-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997
Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47
More information300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS
Section: MOYNO 500 PUMPS Page: 1 of 8 Date: March 1, 1998 SERVICE MANUAL MOYNO 500 PUMPS 300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS Mechanical Seal Models Packing Gland Models MODELS DESIGN FEATURES
More informationIF IT FLOWS THE BOWIE PUMP CAN PUMP IT
IF IT FLOWS THE BOWIE PUMP CAN PUMP IT Bowie Industries, Inc. Bowie, TX 76230 USA Page 1 Bowie Pumps Manual General Pump Information..Page 2 300 Series Pumps.. Page 5 400 Series Pumps.Page 11 500 Series
More informationP7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc
P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc Installation Timing Pin Location CAUTION: Before installing the injection pump, be sure that number 1 cylinder is at the Top Dead Center
More informationBOWIE PUMPS OPERATION - MAINTENANCE
BOWIE PUMPS OPERATION - MAINTENANCE PUMPING PRINCIPLE: The meshing owieeof the gears cause a slight depression, with the resulting enmeshing of the gears causing a vacuum drawing the fluid being pumped
More informationVane Pump & Motor Design Guide
Vickers Service Guide Vane Pump & Motor Design Guide For Mobile Equipment Revised 8/98 353 Introduction Over the past twenty years, the application of hydraulics in agricultural, construction and materials
More informationPressure Relief. Pressure Control Valve R(C)G(O)-03, 06 and 10; R(C)T(O)-03, 06 and 10 VICKERS. Basic Characteristics. Sectional Illustrations
VICKERS Pressure Relief Pressure Control Valve R(C)G(O)-03, 06 and 10; R(C)T(O)-03, 06 and 10 Sectional Illustrations RCG-** Model Shown RCT-** Model Shown Basic Characteristics Type...................
More informationCheck Valves Valve locator
Check Valves Valve locator Functional Symbol Flow Typical Model Cavity Rating Pressure Page Check valve, direct L/min (USgpm) bar (psi) FPR/4 Inline () 5 (5) - FPR/8 Inline (8) 5 (5) - FPR/ Inline 45 ()
More informationChar-Lynn Hydraulic Motors. Repair Information. W Series Geroler Motors 002, 003. April, 1999
Char-Lynn Hydraulic Motors April, 1999 Repair Information W Series Geroler Motors 002, 003 W Series Geroler Motors Tools Required 5/16 inch Hex Key Bullet for Shaft Installation - Eaton Tool No. 600633
More informationChar-Lynn Spool Valve Hydraulic Motors. Repair Information. W Series Geroler Motors
Char-Lynn Spool Valve Hydraulic Motors Repair Information W Series Geroler Motors with Parking Brake 004 Nut Key Ring, Retaining Bearing Ring, Retaining Ring, Retaining Washer (Thick), Pressure Washer,
More informationMetaris has been producing vane pumps and components for over fifteen years.
Metaris has been producing vane pumps and components for over fifteen years. Our products are precision engineered and manufactured to be interchangeable with Vickers and Caterpillar. Metaris vane, gear
More informationVickers Vane Pump & Motor Design Guide For Mobile Equipment
Vickers Vane Pump & Motor Design Guide For Mobile Equipment The Power of One Eaton HANSEN GROMELLE There s a certain energy at Eaton. It s the power of integrating the competencies of some of the world
More informationPRESSURE REDUCING CONTROL VALVE
Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING CONTROL VALVE with LOW FLOW BY-PASS FEATURE Main Line
More information*Rated to 207 Bar/3000 PSI with Aluminum Body. Catalog HY15-3501/US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO.
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. /GPM BAR/PSI STANDARD CHECKS D1A6... 2U... Valve Insert, Ball Type...145/38... 42/6... 5 D1B125... 2C... Valve Insert, Ball Type... 5/132...
More informationQ Series Piston Pumps Variable Displacement, Quiet Series for Industrial Applications
Q Series Piston Pumps Variable Displacement, Quiet Series for Industrial Applications Technical Catalog PVQ10 PVQ13 PVQ20 PVQ25 PVQ32 PVQ40 PVQ45 Table of Contents Introduction......................................................................................................
More informationSTEERING SYSTEM - POWER
STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and
More information*Rated to 207 Bar/3000 PSI with Aluminum Body. Denotes New Winner s Circle Product Line. Catalog HY15-3502/US
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI STANDARD CHECKS D1A6... 2U... Valve Insert, Ball Type...145/38... 42/6... 5 D1B125... 2C... Valve Insert, Ball Type...
More informationRexroth. Spare parts list. Bosch Group. Part No.: R909401762 Designation: VERSTELLPUMPE A4V-125 HD
: R909401762 : VERSTELLPUMPE A4V-125 HD *G* 1 R909400454 ROTARY GROUP L 2 R909414470 HYDRAULIC CONTROL L 3 R909080279 PORT PLATE WITH VALVES L 4 R909400395 INTERNAL GEAR PUMP L 6 R909401736 CONTROL MODULE
More informationVolkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)
47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing
More informationMP8000 Series Pneumatic Valve Actuators
14-1161- 9, Rev. A Technical Bulletin MP8000 Issue Date March 2016 MP8000 Series Pneumatic Valve Actuators Pre-Assembly Details Page 3 MP8000 Actuator Components 3 Tools Required to Assemble an MP8000
More informationOperating Instructions Parts List Manual Scissor Lift Pallet Truck
Operating Instructions Parts List Manual Scissor Lift Pallet Truck Note: Operator MUST read and understand this operating instructions before use this Hand Scissor Lift. Thank you for using this hand scissors
More informationVickers Vane Pumps V Series - Low Noise Vane Pumps. High Performance Intravane Pumps For Industrial Applications
Vickers Vane Pumps V Series - Low Noise Vane Pumps High Performance Intravane Pumps For Industrial Applications The Power of One Eaton HANSEN GROMELLE There s a certain energy at Eaton. It s the power
More informationFisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation
Instruction Manual 1052 Size 20 Actuator (F & G) Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation Contents Introduction... 1 Scope of manual... 1 Description... 1 Specifications...
More informationFOR ANY QUESTIONS, PLEASE CALL US @ 727.347.9915 M-F 8:00a.m.-8:00p.m. EST. REAR BRAKES 1 AEROSPACE COMPONENTS 727.347.9915
REAR BRAKES 1 AEROSPACE COMPONENTS 727.347.9915 REAR BRAKES Before getting started, remove all stock braking components. Pre-assembly of parts: Clean the bolts and the threads in the hat with acetone.
More informationABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions
4057250/8 IM-P405-16 AB Issue 8 ABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4 Operation
More information2003 Audi A4. AUDI' '3.0L V6 - AVK Engine - A4 & A6
Installation (A4) CAUTION: Before installation, ensure camshafts are aligned, crankshaft is locked in place and camshaft gear bolts are loose as described in removal procedures. When turning camshaft,
More informationSeries PVP Variable Volume Piston Pumps
Series PVP Variable Volume Piston Pumps Catalog HY28-2662-CD/US Revised June, 212 hpm12-1.p65, lw, jk 1 Notes Series PVP hpm12-1.p65, lw, jk 2 Introduction Series PVP Series Sizes 6-14 Phased Out For Reference
More informationPallet Jack. OWNER S MANUAL Model MH1230. Important Safety Instructions Assembly Instructions Parts and Hardware Identification
OWNER S MANUAL Model MH1230 Important Safety Instructions Assembly Instructions Parts and Hardware Identification Pallet Jack CAUTION: Read, understand and follow ALL instructions before using this product
More information2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure
2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure Derek Guenther 1/28/2015 Rev. Purpose The purpose of this document is to describe the procedure necessary to replace one of the ball nuts
More informationCatalog HY15-3501/US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI KSWA3... SW-3... Ball sert Type...9./2.... 42/6... 3 K2A... 3Z... Poppet sert Type...38/1... 3/... 4 CS41B... C4-3...
More informationAIR OPERATED OIL PUMPS AND KITS
PM 2 AIR OPERATED OIL PUMPS AND KITS PM 2 Oil pump, pressure ratio : 0 Double acting air operated pumps for transferring lubricants and other non-corrosive fluids. Pump includes bung adapter. New Model
More informationPOWERS Controls No. 4 Pneumatic Damper Actuator
POWERS Controls No. 4 Pneumatic Damper Actuator Technical Instructions Document No. 155-032P25 AP 331-2 Actuator Assembly 331-2929 Typical Actuator Assembly 331-2904 Typical Actuator Assembly 331-3000
More informationVickers. Overhaul Manual. Vane Motors. Vane Motors. 25M, 35M, 45M, 50M Series -20 Design
Overhaul Manual Vickers Vane Motors Vane Motors 25M, 35M, 45M, 50M Series -20 Design Revised 05-01-86 M-2740-S Table of Contents Section Page I. Introduction A. Purpose of Manual..........................................................................
More informationTECHNICAL SERVICE MANUAL
TECHNICAL SERVICE MANUAL HEAVY-DUTY PUMPS SERIES 4195 AND 495 SIZES GG - AL SECTION TSM 144 PAGE 1 of 10 ISSUE D CONTENTS Introduction....................... 1 Safety Information.................... 2
More informationFisher 1061 Pneumatic Piston Rotary Actuator with Style F & G Mounting Adaptations
Instruction Manual 1061 F & G Actuator Fisher 1061 Pneumatic Piston Rotary Actuator with Style F & G Mounting Adaptations Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications...
More informationMONO BLOCK DIRECTIONAL CONTROL VALVE TS1120TSLB
MONO BLOCK DIRECTIONAL CONTROL VALVE TS112TSLB TS TS212TSTSJB P T TS312TSDTSTKJ TS112TSJB FEATURES: O RG PORTS to eliminate leakage. POWER BEYOND CAPABILITY to fit your multi valve circuits. BUILT ANTI-DROP
More informationInstallation and Operating Instructions Installation Instructions for SS EPE-316L Series
INSTR3010 0406 Installation and Operating Instructions Installation Instructions for SS EPE-316L Series Congratulations on your purchase of this Aqua-Pure high flow, single housing filtration system. This
More informationRound Housing with Side Ports
Power Steering Steering Control Unit (SCU) Parts and Repair Information 5 Series Steering Control Units 001 Square Housing with Side Ports Round Housing with Side Ports T E L RP Round Housing with End
More informationSlide the new steering column shaft through the steering column from the driver compartment.
Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.
More informationSeries PAVC Variable Displacement Piston Pumps zp01. Catalog HY28-2662-CD/US
Series PAVC Variable Displacement Piston Pumps zp1 Catalog HY28-2662-CD/US 1 Introduction Series PAVC Quick Reference Data Chart Pump Model Displacement CM 3 /REV (IN 3 /REV) Pump Delivery *Approx. Noise
More informationFlow Control (and Check) Valves FG FCG -01/02/03/06/10. Specifications / Model Number Designation / Others. Min. Metred Flow Capacity
low Control (and Check) Valves -//3/6/ Mounting Specifications / Model Number esignation / Others Specifications Max. Metred low Capacity () Min. Metred low Capacity () Max. Operating Pressure () Approx.
More informationP2/P3 Series Piston Pumps Variable Displacement zp09. Catalog HY28-2662-CD/US
P2/P3 Series Piston Pumps Variable Displacement zp9 Catalog HY28-2662-CD/US A3 Series P2/P3 A4 General Information General Information Series P2/P3 P2 Series The newly developed variable displacement piston
More informationDeZURIK 3-20" BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT
3-20" BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT Instruction D10386 August 2013 Instructions These instructions provide installation, operation and maintenance information for BAW Butterfly Valves.
More informationTri-Homo Style Operation and Maintenance Instructions
Tri-Homo Style Operation and Maintenance Instructions One Research Drive Stratford, CT 06615 (203) 375-0063 www.sonicmixing.com 1 Installation and Start-up Do not perform following adjustments without
More informationMustang Series PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE. M115-2 (Globe) M1115-2 (Angle) Schematic. Standard Components
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Throttles to maintain minimum upstream pressure PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE
More informationCHAPTER 65 TAIL ROTOR DRIVE SYSTEM. Section Title Page
CHAPTER 65 TAIL ROTOR DRIVE SYSTEM Section Title Page 65-00 Description........................................ 65.1 65-10 Tail Rotor Drive Fan Shaft.............................. 65.1 65-20 Tail Rotor
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationBuy Karcher Parts Online: www.pressureparts.com. Need Technical Help? Call: 1-800-999-2245 email Requests to: sales@pressureparts.
Karcher Model: K 620-M * ( 59556440 ) - Parts Section:1.1 TOP PART Page 1 of 18 1 50346460 1 STRAP 2 63031250 6 SCREW 3 50670230 1 COVER 4 63031940 2 SELF-TAPPING SCREW 5 50309650 1 COVER 6 50635710 1
More informationThis instruction is valid for all ACD pump models shown on page 2
Screw pumps ACD Maintenance and Service Instruction This instruction is valid for all ACD pump models shown on page 2 Contents Page List of components 2 Exploded view/ordering code 3 Service intervals
More informationChar-Lynn Disc Valve Motors. Parts Information. 4000 Compact Series
Char-Lynn Disc Valve Motors Parts Information 4000 Compact Series Geroler Motors 00 Parts Drawing/List Displacement cm 3 /r [in 3 /r] 0 [ 9.8] 00 [.3] 50 [5.4] 305 [9.8] 395 [4.0] 490 [9.8] Drive, Main
More informationK&T Saw Shop 606-678-9623 or 606-561-4983
13-600072-06 PRO MAC 8200 05/92 to Current IPL 215710-02 Page 1 of 20 Carburetor Assembly www.ktoutdoor.com 13-600072-06 PRO MAC 8200 05/92 to Current IPL 215710-02 Page 2 of 20 Carburetor Assembly 214763-02
More informationMONO BLOCK DIRECTIONAL CONTROL VALVE TS
SHIPPING: 2332 S 25TH STREET (ZIP 6815) MAILING: P.O. BOX #669 OMAHA, NE 6816 PHONE: (42) 344-4434 FAX: (42) 341-5419 HTTP://WWW.BRAND-HYD.COM MONO BLOCK DIRECTIONAL CONTROL VALVE TS TS312TSDTSTKJB TS2
More informationStainless Steel Single and Dual Circulation Kits
Instruction Sheet P/N 160780 01 Stainless Steel Single and Dual Circulation Kits Introduction The single and dual high-pressure circulation kits allow you to vary and control the circulation rate of coating
More informationEQUALIZER International Limited Range of Mechanical & Hydraulic Flange Spreading Wedges Operator Instruction Manual. B bestflangespreader
EQUALIZER International Limited Range of Mechanical & Hydraulic Flange Spreading Wedges Operator Instruction Manual B bestflangespreader com INDEX THE EQUALIZER RANGE OF MECHANICAL & HYDRAULIC SPREADING
More information2/2 and 3/2 Way Size 6 Seat Valves
2/2 and 3/2 Way Size 6 Seat Valves Directly operated Interface and subplate dimensions according to DIN 24340 and ISO Line connection port size G 3/8" Cartridge design PN [p max. ] = 315 bar 7501856.06.12.08
More informationMedium Pressure Diaphragm Pumps
Medium Pressure Diaphragm Pumps Installation, Operation, Repair, and Parts Manual Description Form L-1382 (10/15, Rev. D) California Proposition 65 Warning -- This product and related accessories contain
More informationCHIPPING HAMMERS. 9949 Tabor Place, Santa Fe Springs, California, CA 90670, U.S.A.
CHIPG HAMMERS Website: www.apt-tools.com e-mail: info@apt-tools.com TDS-1056 Rev A CHIPG HAMMERS TOOL MAINTENANCE & REPAIR INFORMATION FIELD OPERATION: Before use: 1. On 650 Series tools, tighten the handle
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks
TITAN pt. no.: 03 0000 0120 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationPos. Part No. Designation Quantity
Part No.: R902028609 Designation: AA2FM160/61W-VSD510 R902030569 1 R902030998 ROTARY GROUP L 3 R902038553 HOUSING 4 R909409201 PORT PLATE 5 R909084174 CYLINDER PIN 6 R909154656 O-RING D 7 R909083129 SOCKET-HEAD
More informationDive Rite 200 & 300 Bar Isolator Manifold Service Manual
Dive Rite 200 & 300 Bar Isolator Manifold Service Manual Principal Photography and Text by Pete Nawrocky Copyright 2003 Lamartek Inc. D/B/A Dive Rite 0 Warning This manual is only to be used as a guide
More information3 WAY (3/2) POPPET VALVES FOR AIR AND VACUUM SERVICE SOLENOID OR AIR ACTUATED BROCHURE N-223
3 WAY (3/2) POPPET VALVES FOR AIR AND VACUUM SERVICE SOLENOID OR AIR ACTUATED BROCHURE N-223 HERION S HIGH PERFORMANCE POPPET VALVES For those applications requiring high Cv, fast response times, large
More informationARTICLE BEGINNING APPLICATION IDENTIFICATION DESCRIPTION LUBRICATION & ADJUSTMENT TROUBLE SHOOTING. MANUAL TRANSMISSIONS Saab 5-Speed Transaxle
Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Saab 5-Speed Transaxle APPLICATION TRANSMISSION APPLICATION ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Vehicle Application Transmission
More informationRepair of Hyd-ro-ac Actuators
Repair of Hyd-ro-ac Actuators OVERHAUL INSTRUCTIONS SS-.2A-1V SS-.5A-1V SS-.5A-2V Read the entire contents of these instructions before installing the actuator and before making any connections to the
More informationSE-100-1, SE-200-1, SE-500-1, and SE-1000-1 AIR CHAMP PRODUCTS. User Manual SE BRAKE MODELS: (i) MTY (81) 83 54 10 18 ventas@industrialmagza.
AIR CHAMP PRODUCTS User Manual SE BRAKE MODELS: SE-00-, SE-200-, SE-500-, and SE-000- (i) FORM NO. L-20084-E-040 In accordance with Nexen s established policy of constant product improvement, the specifications
More informationVickers Vane Pumps Single and Double Vane Pumps. Model Series V10, V20, V2010, and V2020 for Industrial Equipment
Vickers Vane Pumps Single and Double Vane Pumps Model Series V10, V20, V2010, and V2020 for Industrial Equipment The Power of One Eaton HANSEN GROMELLE There s a certain energy at Eaton. It s the power
More informationHT3 series Peck Feed Drills, with Equal Drill Time
Parts Manual Ersatzteil Liste PL92-280 HT3 series Peck Feed Drills, with Equal Drill Time HT3 SERIES PECK DRILL HT 3 C 005 S E 40 RPM Family Spindle B = 1/2-20 Male Thread, Jacobs Chuck C = 3/8-24 Female
More informationVickers. Overhaul Manual. Steering. Power Steering Pumps. VT16 & VT17 Series
Overhaul Manual Vickers Steering Power Steering Pumps VT16 & VT17 Series Revised 3/1/75 M-1538-S Table of Contents Section I. Introduction.....................................................................................
More informationFleck 4650. Service Manual INSTALLATION AND START-UP PROCEDURE TABLE OF CONTENTS JOB SPECIFICATION SHEET
Fleck 4650 Service Manual TABLE OF CONTENTS JOB SPECIFICATION SHEET...1 INSTALLATION AND START-UP PROCEDURE...1 CONTROL VALVE DRIVE ASSEMBLY...2 CONTROL DRIVE ASSEMBLY FOR CLOCK...3 BYPASS VALVE ASSEMBLY...4
More informationPOSEIDON 2-29, 2-25 & 2-22 POSEIDON 2-29, 2-25 & 2-22 XT
POSEION 2-29, 2-25 & 2-22 POSEION 2-29, 2-25 & 2-22 XT Repair Manual Index A. Safety precautions 3 B. Technical data 4 C. Structure 5-6. Service / Repair 7-23 E. Tools 24 F. Function 25-26 G. Electric
More informationFuel Injection Pump, Rotary (005-014)
Fuel Injection Pump, Rotary View Related Topic Page 1 of 30 Fuel Injection Pump, Rotary (005-014) Table of Contents Summary General Information Preparatory Steps Remove Front Gear Train Rear Gear Train
More informationVickers PVM Piston Pumps
Vickers PVM Piston Pumps 18-141cc 3 (1.1-8.6in 3 ) M-Series Industrial Variable Displacement M-Series Mobile Variable Displacement Table of Contents M Series Variable Displacement Piston Pumps Principles
More informationAir Sleeve Maintenance
Air Sleeve Maintenance and Stuck-Down Troubleshooting Tools required: Safety glasses, gloves, strap wrench, shop towel, 1/4 -diameter 6 breaker bar, FOX High Pressure Pump, dental pick, hex wrench(es)
More informationEasy Tool Retracting System CMC-SR2159ER36
Easy Tool Retracting System CMC-SR2159ER36 Pepperl+Fuchs, Inc. 1600 Enterprise Parkway Twinsburg, Ohio 44087 Phone: +1 330 486 0002 e-mail: pa-info@us.pepperl-fuchs.com Mounting the Easy Tool Refer to
More informationVariable Displacement Pump AA10VSO
Variable Displacement Pump AA10VSO Series 31, Industrial Model, for Open Circuits Axial piston, swashplate design Brueninghaus Hydromatik Sizes 28...140 Nominal pressure 4000 psi Peak pressure 5100 psi
More informationPressure Relief. Pressure Relief Valves. Vickers
Vickers Pressure Relief Pressure Relief Valves Remote Controls, Relief and Sequence Valves, and Single and Multiple Pressure Solenoid and Air Operated Relief Valves 511./EN/1297/A Introduction Remote Controls
More informationAXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION
AXLE SHAFTS - FRONT 1998 Pontiac Bonneville 1998-99 DRIVE AXLES FWD Axle Shafts - Cars - "C", "G" & "H" Bodies GM Aurora, Bonneville, Eighty Eight, LeSabre, LSS, Park Avenue, Regency, Riviera MODEL IDENTIFICATION
More informationWorld Bridge Replacement Parts for EMD 567 and 645 Diesel Engines
40000927-WB REPAIR KIT, WATER PUMP 40005124-WB MAIN & ROD BEARING KIT, 16 CYLINDER 40005125-WB MAIN & ROD BEARING KIT, 20 CYLINDER 40006129-WB PISTON, 645E HTG AND TIN PLATED 40006130-WB PISTON, 645 E3
More informationUnit 24: Applications of Pneumatics and Hydraulics
Unit 24: Applications of Pneumatics and Hydraulics Unit code: J/601/1496 QCF level: 4 Credit value: 15 OUTCOME 2 TUTORIAL 4 DIRECTIONAL CONTROL VALVES The material needed for outcome 2 is very extensive
More informationWater Pump Replacement
1 of 8 2/5/2008 6:36 AM Document ID# 713637 2001 Cadillac Seville Print Water Pump Replacement Tools Required 1. J 38816-A Water Pump Remover & Installer 2. J 38185 Hose Clamp Pliers
More information2003-2004 SID REAR SERVICE GUIDE
2003-2004 SID REAR SERVICE GUIDE For exploded diagram and part number information, refer to the Spare Parts Catalog available on our website at www.rockshox.com. Contact your local distributor or visit
More information2007 Hummer H3. 2007 BRAKES Disc Brakes - H3. Fastener Tightening Specifications Specification Application
2007 BRAKES Disc Brakes - H3 SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Backing Plate Bolts 135 N.m 100 lb ft Brake Hose
More informationTC 170 & TC 170 PD TRANSFER CASE
Automotive Corporation TC 170 & TC 170 PD TRANSFER CASE PARTS MANUAL Fabco Automotive Corporation, Livermore, CA Ph:(925) 454-9500 Fax:(925) 454-9501 1-(800) 967-8838 www.fabcoautomotive.com VII. PARTS
More informationRexroth Hydraulic Pump A10VO Series User Manual
Rexroth Hydraulic Pump A10VO Series User Manual Rexroth Hydraulic pump A10VO Series User Manual Revised 5/1/2009 Page 1 of 12 Functional Purpose This pump is preferred over a fixed displacement (gear)
More informationTrouble Shooting Tech Tips Operation
Steering Components TroubleShooting Tech Tips Table of Contents Basic Steering System Operation 2 Sector Shaft Adjustments 4 Drag Link Adjustment 5 Relief Valve/Unloading Valve Adjustment 6 Ross TAS Automatic
More informationM A N U A L 13-10-05
Documentation The following information sheets illustrate the description below: 12-WW01-4G-E Sectional view of the lance with main dimensions 12-W101-6G-E Sectional view of the head of the lance with
More informationPART 2 FORKLIFT HYDRAULIC SYSTEM
PART 2 FORKLIFT HYDRAULIC SYSTEM Chapter 1 Description and Operation Component Locations & Circuit Layouts 1 Hydraulic Pump 11 Control Valve 14 Valve Section Oil Flows 15 Anti-Cavitation Valve 22 Velocity
More informationVickers. Valves. CM2, CM11, RM3 & FM3 Control Valves. For Mobile Equipment. Revised 4/96
Vickers Valves CM2, CM11, RM3 & FM3 Control Valves For Mobile Equipment Revised 4/96 33 Introduction The directional valves described in this booklet are more than just directional valves -- they are hydraulic
More informationSERIES HYDRAULIC MOTOR DRIVEN CENTRIFUGAL PUMPS
INSTRUCTION MANUAL OASIS WetSeal Technology T M MAX SERIES HYDRAULIC MOTOR DRIVEN CENTRIFUGAL PUMPS 1 2 TABLE OF CONTENTS Pump performance data, dimensions, and part listings are on individual pump specification
More informationMercedes 722.3 722.4
96 Mercedes 7. 7. 5 6 7 8 - Clutch K - Brake Band B - Disc Brake B - Wide Planet Pinion 5 - One-Way Clutch F 6 - Clutch K 7 - Brake Band B 8 - Narrow Planet Pinion Int. Band Fwd. Band Rev. Clutch Direct
More informationRebuild Instructions for 70001 and 70010 Transmission
Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before
More information