Texas Flange. Product Catalog Fax

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Texas Flange. Product Catalog Fax"

Transcription

1 Texas Flange Product Catalog Fax Information In this catalog was compiled from industry sources which Texas Flange & Fitting believes to be reliable. Texas Flange & Fitting Supply, Incorporated, however, does not guarantee the accuracy of this data.

2 TEXAS FLANGE CATALOG This Page is Linkable. This Catalog is Printable. ANSI B , 300, 400, 600, 900, 1500, 2500, Weights ANSI B Note ANSI B Series A Class 150, 300, 400, 600, 900 ANSI B16.47 Series B Class 75, 150, 300, 400, 600, 900 ANSI B16.1- Industry Standard - Class 125LW, 125 SO, 125WN, 250 Boiler Code Flanges - Class 75 SO, 75 WN, 175, 350 AWWA C207-Class 1B, 2D, 3D, 4E, 5E, 6F Studding Outlets - 150, 300, 600, 900, 1500, 2500 Wall Thickness and Bore Chart Phone: Fax: We look forward to hearing from you.

3 12/28/2009 Data Flange Rating Pressure - Temperature Ratings Page 1 of 1 For Steel Pipe Flanges and Flanged Fittings American National Standard ANSI B Ratings apply to materials. SA SA SA SA SA-350-LF2 SA-537-C1.1 3 SA-216-WCB 2 NOTES: CLASS 150 lb. 300 lb. 400 lb. 600 lb. 900 lb lb lb. HYDROSTATIC TEST PRESSURE, PSIG TEMPERATURE, F 1. For service temperatures above 850 F it is recommended that killed steels containing not less than 0.10% residual silicon be used. 2. Upon prolonged exposure to temperatures above 800 F, the carbide phase of carbon steel may be converted to graphite. 3. The material shall not be used in thickness above 2-1/2 in MAXIMUM ALLOWABLE NON-SHOCK PRESSURE PSIG -20 to Flanges of ANSI B16.5 shall not be used for higher ratings except where it is justified by the design methods of the Code. Ratings are maximum allowable non-shock working pressures expressed as gage pressure, at the tabulated temperatures and may be interpolated between temperatures shown. Temperatures are those on the inside of the pressure-containing shell of the flange. In general, it is the same as that of the contained material. THIS INFORMATION IF PROVIDED FOR GENERAL INFORMATION PURPOSES ONLY. BEFORE USING ANY OF THIS DATA FOR ANY PURPOSE OTHER THAN FOR GENERAL INFORMATION, IT SHOULD BE REVIEWED AND CERTIFIED BY A QUALIFIED ENGINEER.

4 ANSI B16.5 Class 150 Forged Flanges Weld Neck Threaded Slip- On Lap Joint Socket Weld Nom. Bolt No.2/Dia. Pipe O T1 R X Circle L21 H B23 L B r L34 B3 D of Dia. ½ ¾ ¼ ½ ½ ½ Dimensions in inches /16 in. raised face included in dimensions T, L and L2. Bolt hole diameter 1/8 in. larger than bolt diameter. 3- Standard Bore dimensions provided. 4- This dimension is commonly associated with "true" Lap Joints. Industry standard is to make to the slip on length thru the hub.

5 ANSI B16.5 Class 300 Forged Flanges Weld Neck Threaded Slip- On Nom. Pipe Lap Joint Socket Weld O T1 R X No.2 & Dia. of Bolt Circle Dia. L21 H B23 L B r L34 B3 D C Thr ½ ¾ ¼ ½ ½ ½ Dimensions in inches. 1-1/16 in. raised face included in dimensions T, L and L2. 2- Bolt hole diameter 1/8 in. larger than bolt diameter. 3- Standard Bore dimensions provided. 4- This dimension is commonly associated with "true" Lap Joints. Industry standard is to make to the slip on length thru the hub.

6 ANSI B16.5 Class 400 Forged Flanges Weld Neck Threaded Slip- On Nom. Pipe Lap Joint Socket Weld O T1 R X No.2 & Bolt Dia. of Circle Dia. L21 H B2 L B r L3 B3 D C Thr ½ ¾ S p ¼ e ½ c i ½ f i e ½ d by P u r c h a s e r Dimensions in inches. s NPS 1/2 through 3-1/2 are same as Class 600 flanges. 1-1/4 in. raised face not included in dimensions T, L and L2. 2- Bolt hole diameter 1/8 in. larger than bolt diameter.

7 ANSI B16.5 Class 600 Forged Flanges Weld Neck Threaded Slip- On Nom. Pipe Lap Joint Socket Weld O T1 R X No.2 and Dia. of Bolt Bolt Circle Dia. L21 H B2 L B r L3 B3 D C Thr ½ To ¾ Be ¼ S ½ p e ½ c i f 3½ i e d by P u r c h a s e r Dimensions in inches. s NPS 1/2 through 3-1/2 are same as Class 400 flanges. 1-1/4 in. raised face not included in dimensions T, L and L2. 2- Bolt hole diameter 1/8 in. larger than bolt diameter.

8 ANSI B16.5 Class 900 Forged Flanges Weld Neck Threaded Slip- On Nom. Pipe Lap Joint Socket Weld O T1 R X No.2 and Bolt Dia. of Circle Bolt Dia. L21 H B2 L B r L3 B3 Thr s ½ Thru 2 ½ Are Identical To Class Dimensions in inches. s NPS 1/2 through 3-1/2 are same as Class 1500 flanges. 1-1/4 in. raised face not included in dimensions T, L and L2. 2- Bolt hole diameter 1/8 in. larger than bolt diameter. Specified by purchaser

9 ANSI B16.5 Class 1500 Forged Flanges Weld Neck Threaded Slip- On Lap Joint Socket Weld Nom. Pipe O T1 R X No.2 & Dia. of Bolt Bolt Circle Dia. L21 H B2 L B r L3 D B3 Thr 1/2" / / / / /4 in. raised face not included in dimensions T, L and L2. Specified by Purchaser 2- Bolt hole diameter 1/8 in. larger than bolt diameter.

10 ANSI B16.5 Class 2500 Forged Flanges Weld Neck Threaded Slip- On Nom. Pipe Lap Joint O T1 R X No.2 & Dia. of Bolt Bolt Circle Dia. L21 H B2 L B r L3 B3 Thr 1/2" / / / / Dimensions in inches. 1-1/4 in. raised face not included in dimensions T, L and L2. Specified by Purchaser 2- Bolt hole diameter 1/8 in. larger than bolt diameter.

11 Pressure Class 150 ANSI B16.5 Forged Steel Flanges Approximate Weight (L.B.S.) Nom. Pipe Weld Neck Slip- On Thd Lap Joint Socket Pressure Weld Class Nom. Pipe Weld Neck Slip- On Lap Socket Thd Joint Weld 1/ / / / / / / / / / / / / / / / / /

12 Nom. Pressure Weld Slip- Class Neck On Pipe Thd Lap Socket Joint Weld Nom. Pressure Class Pipe Weld Neck Slip- On Thd Lap Socket Joint Weld / WEIGHT UPON APPLICATION / / / / / / / / / Weights of Class 400 flanges, sizes NPS 1/2 through 3-1/2 are same as Class 600. Weights of Class 900 flanges, sizes NPS 1/2 through 3-1/2 are same as Class 1500.

13 A Quick Note on B16.47 ASME has incorporated the MSS-SP44 specification into B16.47 Seiries A and the API 605 Specification into B16.47 series B. They have also added s to these two specs. You may note that these specs include only Weld Necks and s. For Slip-On s over 24 you must refer to either Industry Standard (which are not automatically covered by ASME) or Boiler Code Flanges. If you need help deciding which flange best suits your application feel free to contact us.

14 B16.47 Series A Class 150 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld OD Dia at Dia Bolt Dia # Weld OD Bore LTH Neck RF Base Bevel Circle Neck O C C R X B Y A To be specified by Purchaser. Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

15 B16.47 Series A Class 300 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld OD Dia at Dia Bolt Dia # Weld OD Bore LTH Neck RF Base Bevel Circle Neck O C C R X B Y A To be specified by Purchaser. Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

16 B16.47 Series A Class 400 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld Dia at Dia OD Bolt # Dia Weld OD LTH Neck Base Bevel RF Circle Neck O C C Y X A R Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

17 B16.47 Series A Class 600 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld Dia at Dia OD Bolt # Dia Weld OD LTH Neck Base Bevel RF Circle Neck O C C Y X A R , , ,108 Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

18 B16.47 Series A Class 900 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld Dia at Dia OD Bolt # Dia Weld OD LTH Neck Base Bevel RF Circle Neck O C C Y X A R , ,398 Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

19 B16.47 Series B Class 75 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld OD Dia at Dia Bolt Dia # Weld OD Bore LTH Neck RF Base Bevel Circle Neck O C C R X B Y A To be specified by Purchaser. Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

20 B16.47 Series B Class 150 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld OD Dia at Dia Bolt Dia # Weld OD Bore LTH Neck RF Base Bevel Circle Neck O C C R X B Y A To be specified by Purchaser. Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

21 B16.47 Series B Class 300 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld OD Dia at Dia Bolt Dia # Weld OD Bore LTH Neck RF Base Bevel Circle Neck O C C R X B Y A To be specified by Purchaser. Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

22 B16.47 Series B Class 400 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld Dia at Dia OD Bolt # Dia Weld OD LTH Neck Base Bevel RF Circle Neck O C C Y X A R Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

23 B16.47 Series B Class 600 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld Dia at Dia OD Bolt # Dia Weld OD LTH Neck Base Bevel RF Circle Neck O C C Y X A R , , ,108 Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

24 B16.47 Series B Class 900 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld Dia at Dia OD Bolt # Dia Weld OD LTH Neck Base Bevel RF Circle Neck O C C Y X A R , ,398 Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

25 Same as AWWA Class D Hub Class 125LW* ( psi) Drilling Template Nom Pipe OD of Flange ID of Flange Thickness of Flange Overall Thickness Diam. Of Hub Number of Bolt Diam. of Bolt Diam. of Bolt Circle Weight (A) (B) (T) (L) (E) (C) Notes: All dimensions measured in inches. All weights in pounds and are approximate. Hub flanges are to be used on pipe that has an OD equal to the nominal pipe size in the first column. *Pressure Ratings are from AWWA Table 3 Class D. Pressure rating at atmospheric temperature: sizes 4-12 in. inclusive, 175 psi; sizes larger than 12 in., 150 psi. These flanges have the same diameter and drilling as ANSI/ASME B16.1 class 125 cast-iron flanges. In sizes 24in. and smaller they also match up to ANSI/ASME B psi standard for steel flanges.

26 Same as AWWA Table 4 Class E Class 125 SO* (275psi) Drilling Template Nom Pipe OD of Flange ID of Flange Thickness of Flange Overall Thickness Diam. Of Hub Number of Bolt Diam. of Bolt Diam. of Bolt Circle Weight (A) (B) (T) (L) (E) (C) Notes: Commonly referred to as a class 150# in large diameter. Can be furnished with a raised face. All dimensions measured in inches. All weights in pounds and are approximate. *Pressure ratings from AWWA table 4 Class E. Pressure rating at atmospheric temperature is 275 psi. These flanges have the same diameter and drilling as ANSI/ASME B16.1 class 125 cast-iron flanges. In sizes 24in. and smaller they also match ANSI/ASME B psi standard for steel flanges. The thickness of a 150-psi flange from which the raised face has been removed shall be no less than dimension T minus 0.06 in.

27 Nom Pipe OD of Flange ID of Flange Thick Overall Thickness Class 125 WN Diam. Of Hub OD of Raised Face Diam. Hub At Bev. # of Bolt Drilling Template Diam. of Bolt Diam. of Bolt Circle Weight (O) (B) (C) (Y) (X) (R) (A) To Be Specified by Purchaser Notes: Can be furnished with a flat face. All dimensions measured in inches. All weights in pounds and are approximate. These flanges have the same diameter and drilling as ANSI/ASME B16.1 class 125 castiron flanges.

28 Class 250* (300psi) Matches B16.1 Class 250 Valves and Pumps Nominal Pipe OD of Flange ID of Flange Thick WN LTH SO Hub Dia Drilling Template Diam. of Bolt Number of Bolt Diam. of Bolt Circle Weights (O) (B) (C) (Y) (Y) (X) Weld Slipon Neck Notes: All dimensions measured in inches. All weights in pounds and are approximate. *AWWA Pressure rating at atmospheric temperature is 300 psi. These flanges have the same diameter and drilling as ANSI/ASME B16.1 class 250 cast iron pipe and flanged fittings.

29 Industry Standard CLASS 75 Slip-On & Slip-On THICKNESS Drilling Weight Nom Slip- OD Dia at Bolt Dia # Slip- OD Bore LTH On RF Base Circle On O C C R X B Y Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

30 Industry Standard CLASS 75 Weld Neck & Weld Neck THICKNESS Drilling Weight Nom Weld OD Dia at Dia Bolt Dia # Weld OD Bore LTH Neck RF Base Bevel Circle Neck O C C R X B Y A To be specified by Purchaser. To be determined by design requirements Dimensions in inches. Note: Larger sizes as well as intermediate sizes can be furnished.

31 Industry Standard Class 175 Nom Weld Neck Thickness (C) Continued on next page Bore Slip 0n Length Thru Hub (Y) Dia. Hub at bevel OD Weld Slip Hub RF Neck On Dia WN SO WN SO O R X B1 B2 A To be specified by purchaser To be established by design requirements.

32 Class 175 continued from previous page Drilling Approx. Weight Nom BC Dia. Dia. of # of Weld Neck Slip On Notes: s are nominal inside diameters of pipe or shell used with Welding Neck flanges, and nominal outside diameters of pipe or shell used with Slip-On flanges. Larger sizes as well as intermediate sizes can be furnished.

33 Industry Standard Class 350 Nom Weld Neck Thickness (C) Continued on next page Bore Slip 0n Length Thru Hub (Y) Dia. Hub at bevel OD Weld Slip Hub RF Neck On Dia WN SO WN SO O R X B1 B2 A To be specified by purchaser. To be established by design requirements.

34 Class 350 continued from previous page Drilling Approx. Weight Nom BC Dia. Dia. of # of Weld Neck Slip On Notes: s are nominal inside diameters of pipe or shell used with Welding Neck flanges, and nominal outside diameters of pipe or shell used with Slip-On flanges. Larger sizes as well as intermediate sizes can be furnished.

35 Formally Table 1 Class B Table 2 Class B (s from table 7) Nominal Pipe OD of Flange AWWA standard steel-ring flanges, Class B* (86 psi) ID of Flange Thickness of Flange (T) Number of Bolt Drilling Template Diam. of Bolt Diam. of Bolt Circle Weights (A) (B) Slip-On (C) Slip-on Notes: All dimensions measured in inches. All weights in pounds and are approximate. *Pressure rating at atmospheric temperature is 86 psi. These flanges have the same OD and drilling as ANSI/ASME B16.1 class 125 cast-iron flanges. In sizes 24in. and smaller they also match ANSI/ASME B psi standard for steel flanges.

THIS PAGE INTENTIONALLY LEFT BLANK

THIS PAGE INTENTIONALLY LEFT BLANK (713) 690-0040 THIS PAGE INTENTIONALLY LEFT BLANK ORIFICE FLANGES In Carbon, Alloy and Stainless 300lb. through 2500 lb. or Ring Joint ORIFICE FLANGES are widely used in conjunction with orifice meters

More information

SEAMLESS WELDED FITTINGS

SEAMLESS WELDED FITTINGS SEAMLESS WELDED FITTINGS WALL THICKNESS NPS Pipe 2 A B K D V E F G O.D. Light SCH SCH STD SCH SCH X-SIG SCH SCH SCH SCH SCH XX NPS Wall 20 0 40 60 80 00 20 40 60 Stg ASA MSS /2.840.08 --- ---.09.09 ---.4.4

More information

Dimensions for Forged Steel Flanges

Dimensions for Forged Steel Flanges 150 lb Flanges Length Through Hub Bore Drilling Nominal Pipe Size Outside Thickness of of Flange Flange ( O ) ( C ) of Raised Face ( R ) of Hub at Base (Note 1) ( X ) Hub Beginning of Chamfer Neck ( A

More information

Robert-James Sales, Inc. Orifice Flanges. Weld Neck, Slip-On, Threaded. ASME Class

Robert-James Sales, Inc. Orifice Flanges. Weld Neck, Slip-On, Threaded. ASME Class Robert-James Sales, Inc. Orifice s Weld Neck, Slip-On, Threaded. ASME Class 300-2500 43 Class 300, Welding Neck, Slip-On and Threaded ASME B16.36 Orifice s O Thickness Min. C R Length Thru Slip-On and

More information

Caps STANDARD WEIGHT Inches / Pounds

Caps STANDARD WEIGHT Inches / Pounds Standard Caps you are here: Home > Weldbend Catalog > Fittings > Caps Caps STANDARD WEIGHT Inches / Pounds For Metric Units >Click Here Nominal Pipe Size Outside Inside Wall Thickness (T) Length (E) Pipe

More information

BS 4504 Circular Flanges - General

BS 4504 Circular Flanges - General BS 4 Circular Flanges - General British Standard BS 4 : Section 3.1 : 1989 - Circular Flanges for Pipes, Valves and Fittings ( Designated), Specification for Steel Flanges. This covers flanges in nominal

More information

Gas Distribution and Transportation

Gas Distribution and Transportation Piping System Includes: Pipe Fittings (e.g. elbows, reducers, branch connections, etc.) Flanges, gaskets, bolting Valves Associations involved in generating Codes for piping Design Engineering: ASME ANSI

More information

WEIGHT OF PIPING MATERIALS

WEIGHT OF PIPING MATERIALS WEIGHT OF PIPING MATERIALS WEIGHTS OF PIPING MATERIALS INTRODUCTION The tabulation of weights of standard piping materials presented on the following pages has been arranged for convenience of selection

More information

Stainless Steel Pipe and Flanges

Stainless Steel Pipe and Flanges Stainless Steel Pipe and Flanges Stainless Steel 4 Pipe and Flanges Photography courtesy of Outokumpu, Arcelor, Atlas Steels and New Zealand Tube Mills. Stainless steel pipe and fittings A stainless steel

More information

BRIDAS. En cuanto a los materiales, los más utilizados son los aceros al carbono, aceros aleados y aceros inoxidables.

BRIDAS. En cuanto a los materiales, los más utilizados son los aceros al carbono, aceros aleados y aceros inoxidables. BRIDAS Gestión de Compras suministra bridas para el mercado nacional e internacional, según normativas ANSI, BS, DIN, JIS, ISO, China GB/T, KS, etc, así como según especificaciones del cliente Suministramos

More information

CL-99 YALE QUICK OPENING CLOSURES

CL-99 YALE QUICK OPENING CLOSURES CL-99 YALE QUICK OPENING CLOSURES For fast, easy and economical accessibility to pipelines and other vessel applications, think first of the broad family of Yale closures. Yale closures feature quick-opening

More information

1.3.3 When pipe is required for close coiling, this should b specified on the order.

1.3.3 When pipe is required for close coiling, this should b specified on the order. SA 36* SA 53* Covers carbon steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded contrsuction of bidges and buildings, and for general structural purposes. When the

More information

Forged High Pressure Pipe Fittings

Forged High Pressure Pipe Fittings Forged High Pressure Pipe Fittings Forged High Pressure Pipe Fittings Summary : Type 1. Elbow, Tee, Cross, Coupling, Half Coupling, Cap, Plug, Bushing, Union, HEX. Nipple, Swage nipple, Bull Plug, Street

More information

PIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification. 96 B. Riutta

PIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification. 96 B. Riutta PIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification Number: 3503-11.2.610 Rev. 2 Rubber Lined Steel Pipe and Fittings Mechanically Coupled Plain End Type System Issued Revised Approved

More information

WELDED AND SEAMLESS PIPE

WELDED AND SEAMLESS PIPE WELDED AND SEAMLESS PIPE MATERIAL SPECIFICATIONS Antec offers a stock range of seamless and longitudinally welded pipe to American standards, with other specifications (eg: spirally welded) available to

More information

SECTION 8 AMERICAN. Flanged Pipe

SECTION 8 AMERICAN. Flanged Pipe SECTION 8 AMERICAN Flanged Pipe The principal standards covering Flanged Pipe are ANSI/AWWA C115/A21.15 and ANSI/AWWA C110/A21.10. These and other standards are referenced throughout this Section either

More information

PIPE INDEX STAINLESS STEEL WELDED / SEAMLESS PIPE DIMENSION AND WEIGHT 2

PIPE INDEX STAINLESS STEEL WELDED / SEAMLESS PIPE DIMENSION AND WEIGHT 2 INDEX STAINLESS STEEL WELDED / SEAMLESS DIMENSION AND WEIGHT STAINLESS STEEL WELDED TYPE 0L S, ALLOWABLE WORKING PRESSURE STAINLESS STEEL WELDED TYPE 0 ALLOWABLE WORKING PRESSURE STAINLESS STEEL WELDED

More information

Vogt Valves The Connection Bulletin for Extended Body Forged Steel Valves Welded Bonnet, Bolted Bonnet, Class 800 & Class 1500 CB 22

Vogt Valves The Connection Bulletin for Extended Body Forged Steel Valves Welded Bonnet, Bolted Bonnet, Class 800 & Class 1500 CB 22 The Connection Bulletin for Extended Body Forged Steel Valves Welded Bonnet, Bolted Bonnet, Class 800 & Class 1500 CB 22 Extended Body Forged Steel Valves An extended body gate valve specifically designed

More information

MALLEABLE IRON THREADED FITTINGS

MALLEABLE IRON THREADED FITTINGS MALLEABLE IRON THREADED FITTINGS /METRIC INDEX MALLEABLE IRON THREADED FITTINGS PAGE 90 ELBOWS CLASS 150 M.I. 4 CLASS 300 M.I. 12 PAGE 90 STREET ELBOWS CLASS 150 M.I. 8 90 REDUCING ELBOWS CLASS 150 M.I.

More information

Butt Weld Pipe Fittings

Butt Weld Pipe Fittings Butt Weld Pipe Fittings Butt Weld Fittings Dimension aterial Spec. aterial Grades : ANSI B16.9, B16.25, B16.28, SS SP-43, SP-48, SP-59 : AST A403, A240, A312, A234 WPB : 304, 304L, 316, 316L, ARBON STEEL

More information

The Augustus Group Products Projects and Engineering Consulting. ASME BOILER AND PRESSURE VESSEL CODE Mike Looram

The Augustus Group Products Projects and Engineering Consulting. ASME BOILER AND PRESSURE VESSEL CODE Mike Looram The Augustus Group Products Projects and Engineering Consulting ASME BOILER AND PRESSURE VESSEL CODE Mike Looram ASME B&PV CODE SECTION VIII DIV. 1 Bolted Flanges With Ring Type Gaskets Stress Calculations

More information

60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING

60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING 60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed

More information

Description of Bolt Torque Tables

Description of Bolt Torque Tables Description of Bolt Torque Tables (in) (in) (in) (sq.in.) Bolts (in) (ft.lbs.) (psi) (psi) (psig) (psi) (ft.lbs.) (psi) (ft.lbs.) 0.5 0.84 1.38 0.94 4 0.5 60 7560 32134

More information

Yes, we can. Pipe & Fittings Data Charts. CARBON pipe STEEL BUTTWELDING yes FITTINGS we can TO ASME B16.9, B16.28 fittings & BS.

Yes, we can. Pipe & Fittings Data Charts. CARBON pipe STEEL BUTTWELDING yes FITTINGS we can TO ASME B16.9, B16.28 fittings & BS. CARBON pipe STEEL BUTTWELDING yes FITTINGS we can TO ASME B16.9, B16.28 fittings & BS.16 Yes, Pipe & Fittings Data Charts we can. pipe yes we can fittings www.onesteelmetalcentre.com We understand. With

More information

www.klmtechgroup.com TABLE OF CONTENT

www.klmtechgroup.com TABLE OF CONTENT Page : 1 of 16 Project Engineering Standard www.klmtechgroup.com KLM Technology #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malaysia ORIFICE FLANGES TABLE OF CONTENT SCOPE

More information

DESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4

DESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4 DESCRIPTION PAGE B7 Studs and Nuts Stud Bolts for Pressure-Temperature Piping 2-1 General Purpose End-to-End Studs 2-2 Tap End Stud Bolts 2-3 Double End Stud Bolts 2-4 Sigma Fasteners, Inc. Section 2 STUD

More information

Rosemount 1495 Orifice Plate, 1496 Orifice Flange Union

Rosemount 1495 Orifice Plate, 1496 Orifice Flange Union Reference Manual Rosemount 1495 Orifice Plate, 1496 Orifice Flange Union Rosemount 1495 Orifice Plate Rosemount 1496 Orifice Flange Union www.rosemount.com Reference Manual Rosemount 1495, 1496 Rosemount

More information

Section 7. Socket Weld and Threaded Fittings. Socket Weld and Threaded Fittings 7-1

Section 7. Socket Weld and Threaded Fittings. Socket Weld and Threaded Fittings 7-1 Section 7 Socket Weld and Threaded Fittings This Section contains dimension and tolerance information extracted from American and British specifications applicable to socket weld and threaded fittings.

More information

PLUMBING RE-SUBMITTAL 22 11 17

PLUMBING RE-SUBMITTAL 22 11 17 PLUMBING RE-SUBMITTAL 22 11 17 ACADEMIC BUILDING & PATRIOT S CASA TEXAS A&M UNIVERSITY - SAN ANTONIO, TX NO. 25-3122, VAC NO. 39019 OWNER: ARCHITECT: MEP ENGINEER: GENERAL CONTRACTOR: PLUMBING CONTRACTOR:

More information

RING JOINT SYSTEMS 207

RING JOINT SYSTEMS 207 RING JOINT SYSTEMS 07 08 Table of Contents Model R-88 Pages 10-11 Model R-88 Large Diameter Page 1 Model RH-1000 1000 PSI Coupling Page 13 Model RX-3000 3000 PSI Coupling Page 1 Model RX-3770 3770 PSI

More information

ANSI/ASME B36.19M-1985 ANSI/ASME B36.10M-1995 ISO 4200: 1991(E) unit length (presented with ISO 4200 data)

ANSI/ASME B36.19M-1985 ANSI/ASME B36.10M-1995 ISO 4200: 1991(E) unit length (presented with ISO 4200 data) Section 5 Pipe and Tube Sizes This Section contains pipe and tube dimensions and weights, and information on specific applications. (Pipe threads and surface finishes are covered in Section 10. Weld bevels

More information

Stainless Steel Pipe

Stainless Steel Pipe ASME B36.19M-2004 (Revision of ANSI/ASME B36.19M-1985) Stainless Steel Pipe AN AMERICAN NATIONAL STANDARD A N A M E R I C A N N A T I O N A L S T A N D A R D STAINLESS STEEL PIPE ASME B36.19M-2004 (Revision

More information

ASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16.

ASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16. ASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16.4-1998 - Cast Iron Threaded Fittings ASME/ANSI B16.5-1996 - Pipe

More information

Carbon. Stainless. We have you covered >TUBING >PIPE >BAR >TUBING >PIPE >FITTINGS >FLANGES >BAR

Carbon. Stainless. We have you covered >TUBING >PIPE >BAR >TUBING >PIPE >FITTINGS >FLANGES >BAR Carbon or Stainless Carbon >TUBING >PIPE >BAR Alloy Stainless Steel Aluminum >TUBING >PIPE >FITTINGS >FLANGES >BAR We have you covered www.mkcanada.com www.specialtysteels.com Looking for Carbon tubing,

More information

12.1 MUELLER TAPPING MATERIALS AND SPECIALTY VALVES. MUELLER Tapping Valves. MUELLER Tapping Sleeves and Crosses

12.1 MUELLER TAPPING MATERIALS AND SPECIALTY VALVES. MUELLER Tapping Valves. MUELLER Tapping Sleeves and Crosses MUELLER TAPPING MATERIALS AND SPECIALTY VALVES 12.1 MUELLER Tapping Sleeves and Crosses Full range of Tapping Sleeves and Crosses to fit most types of pipe including cast iron, ductile iron, A-C, and cast

More information

FLANGED FITTINGS OUR KNOWLEDGE SETS US APART

FLANGED FITTINGS OUR KNOWLEDGE SETS US APART OUR KNOWLEDGE SETS US APART Elbows Tees Crosses Wyes Reducers Flanges Converters Gaskets Nuts & Bolts TABLE OF CONTENTS Flange Details - Class 125............................................2 Designation

More information

Copper and Copper Alloy Tube, Pipe and Fittings

Copper and Copper Alloy Tube, Pipe and Fittings Copper and Copper Alloy Tube, Pipe and Fittings COPPER and COPPER ALLOY TUBE and PIPE Seamless Copper Pipe: Copper pipe is almost pure copper manufactured to the requirements of ASTM B 42 - Standard Specification

More information

2014 Edition 3"-64" NSF. industrial Applications, water & Wastewater. Certified to ANSI/NSF 61

2014 Edition 3-64 NSF. industrial Applications, water & Wastewater. Certified to ANSI/NSF 61 3"-64" Ductile Iron industrial Applications, water & Wastewater 866.DI.IE 2 Table of Contents Flanged ipe for Water and Other Liquids 3 Ductile Iron Flanged ipe With Threaded Flanges-Flanged Details 5

More information

NFPA 13 Standard for the Installation of Sprinkler Systems

NFPA 13 Standard for the Installation of Sprinkler Systems Tentative Interim Amendment NFPA 13 Standard for the Installation of Sprinkler Systems 2013 Edition Reference: Chapter 6 TIA 13-2 (SC 12-8-24/TIA Log #1054) Note: Text of the TIA issued and incorporated

More information

Spectifications. ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers)

Spectifications. ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) Spectifications ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) ANSI / ASME B1.20.1 ASME B16.10 ASME B16.11 ASME B16.25 ANSI / ASME B16.28 ANSI / ASME B16.34

More information

Stainless Steel Piping Products

Stainless Steel Piping Products Stainless Steel Piping Products Stainless Steel and Other Corrosion Resistant Metal Pipe, Tubing, Flanges and Fittings ALASKAN COPPER WORKS A laskan stainless steel pipe and fittings are found throughout

More information

Pipe Flanges and Flanged Fittings

Pipe Flanges and Flanged Fittings ASME B16.5-2013 (Revision of ASME B16.5-2009) Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24 Metric/Inch Standard AN AMERICAN NATIONAL STANDARD ASME B16.5-2013 (Revision of ASME B16.5-2009)

More information

CALCULATION & DRAFTING STANDARDS MANUAL PROCEDURE: C&D 515 Bill of Materials Standard REV 0.0 5/6/04

CALCULATION & DRAFTING STANDARDS MANUAL PROCEDURE: C&D 515 Bill of Materials Standard REV 0.0 5/6/04 BROWN MINNEAPOLIS TANK PAGE 1 OF 7 PURPOSE: Create and Drawing Uniformity Create, explain, and establish a standard bill of materials to be placed on every drawing (except the overall tank elevation and

More information

Technical Note PP 811-TN PE Flange Connections

Technical Note PP 811-TN PE Flange Connections Technical Note PP 811-TN PE Flange Connections Flange Connection Flanged joints are made using a DriscoPlex Flange Adapter that is fused to the pipe then joined to a mating flange adapter or a mating appurtenance

More information

STAINLESS STEEL FLANGES

STAINLESS STEEL FLANGES STAINLESS STEEL FLANGES Stainless Steel Flanges Stainless Steel Flanges Viraj is the world leader in stainless steel forged flanges. We serve customers across 90 countries and six continents. Viraj flanges

More information

Pipe and Tubing PIPE. Black and Galvanized Steel Pipe. Standard and Extra Strong Welded Steel Pipe

Pipe and Tubing PIPE. Black and Galvanized Steel Pipe. Standard and Extra Strong Welded Steel Pipe Black and Galvanized Steel Pipe PIPE Wheatland Steel Pipe is made by specialists who understand that it s the small details that make the difference between average products and superior products. At the

More information

316L Pipe Sizing Calculations and Tables

316L Pipe Sizing Calculations and Tables DISCUSSION For piping systems constructed with a minimum ¾ to a maximum 2-1/2 316L seamless pipe (A312). The physical dimensions and mechanical properties are listed below: Material: 316L : ¾ 2-1/2 Schedule

More information

Equivalents & Conversion Factors 406 Capacity Formulas for Steam Loads 407 Formulas for Control Valve Sizing 408-409

Equivalents & Conversion Factors 406 Capacity Formulas for Steam Loads 407 Formulas for Control Valve Sizing 408-409 Engineering Data Table of Contents Page No. I II Formulas, Conversions & Guidelines Equivalents & Conversion Factors 406 Capacity Formulas for Steam Loads 407 Formulas for Control Sizing 408-409 Steam

More information

JCM TAPPING SLEEVES MORE SELECTION, BENEFITS, OPTIONS

JCM TAPPING SLEEVES MORE SELECTION, BENEFITS, OPTIONS JCM TAPPING SLEEVES MORE SELECTION, BENEFITS, OPTIONS Specifying the right tapping sleeve for the condition of the job is the best way to assure a successful tap. JCM s are readily available in a wide

More information

A Table of the Most Common Standard Pipe Sizes. Nominal Bore 1/2 inch (DN 15 mm), Outside Diameter 21.34 mm

A Table of the Most Common Standard Pipe Sizes. Nominal Bore 1/2 inch (DN 15 mm), Outside Diameter 21.34 mm Standard Pipe Sizes Standard Pipe Sizes Except for specialist applications, commercially available pipe comes in standard sizes. Pipes in a variety of materials - including carbon steel, steel alloys,

More information

Series 25114 150# Flanged Cast Steel Check Valve

Series 25114 150# Flanged Cast Steel Check Valve Series 25114 150# langed Cast Steel Check Valve eatures SHARPE - SERIES 25114 150# langed Cast Steel Check Valve Bolted Cover Swing Type or Horizontal or Vertical lines Integral Seat langed Ends Butt Weld

More information

CUTTING TOOLS FOR MACHINE SHOP USE

CUTTING TOOLS FOR MACHINE SHOP USE CUTTING TOOLS FOR MACHINE SHOP USE WORK HOLDING TOOLS, CUTTING TOOLS AND SHOP ACCESSORIES T-Slot Bolts Nuts and Washers Set-up Wedges 14 FRONT SIDE WORK HOLDING TOOLS MACHINE SHOP USE Nut Washer T-Slot

More information

A A A T E C H N O L O G Y

A A A T E C H N O L O G Y A A A T E C H N O L O G Y & SPECIALTIES CO., INC. V A R I A B L E S P R I N G H A N G E R S A N D S U P P O R T S TOTAL SOLUTION SERVICE For the Industrial Piping Marketplace 2012 www.aaatech.com 4 1 Y

More information

TS 59 SOUTH AUSTRALIAN WATER CORPORATION

TS 59 SOUTH AUSTRALIAN WATER CORPORATION TS 59 SOUTH AUSTRALIAN WATER CORPORATION TECHNICAL STANDARD SPECIFICATION FOR EWS DEPARTMENTAL FLANGES - 1983 Reference Specification Only Issued by: Manager Engineering Issue Date: 01 May 1983 SA WATER

More information

CONSULTANT PROCEDURES & DESIGN GUIDELINES Steam and Condensate Piping and Pump Systems

CONSULTANT PROCEDURES & DESIGN GUIDELINES Steam and Condensate Piping and Pump Systems GENERAL: Steam and condensate piping and pump systems included in this document are for building systems starting at the pressure reducing station (PRV). DESIGN GUIDELINES: A. Design General 1. Definitions:

More information

Stainless Steel Threaded Pipe Nipples

Stainless Steel Threaded Pipe Nipples TYPE 304/ Schedule 40 Welded DIAM LENGTH PRICE LENGTH IN INCHES Stainless Steel Threaded Pipe Nipples INCHES OF CLOSE EACH 1-1/2 2 2-1/2 3 3-1/2 4 4-1/2 5 5-1/2 6 7 8 9 10 11 12 1/8 3/4 13.60 17.79 21.24

More information

ANALYSIS OF GASKETED FLANGES WITH ORDINARY ELEMENTS USING APDL CONTROL

ANALYSIS OF GASKETED FLANGES WITH ORDINARY ELEMENTS USING APDL CONTROL ANALYSIS OF GASKETED FLANGES WITH ORDINARY ELEMENTS USING AP... Page 1 of 19 ANALYSIS OF GASKETED FLANGES WITH ORDINARY ELEMENTS USING APDL CONTROL Yasumasa Shoji, Satoshi Nagata, Toyo Engineering Corporation,

More information

2013 Edition. Flanged fittings 30"-64" NSF. industrial Applications, water & Wastewater. Certified to ANSI/NSF 61

2013 Edition. Flanged fittings 30-64 NSF. industrial Applications, water & Wastewater. Certified to ANSI/NSF 61 30"-64" Ductile Iron industrial Applications, water & Wastewater 2 Table of Contents Flanged Fittings for Water 3 Flange Details 5 Flanged Fittings 6 90º and 45º Bend 6 22-1/2º and 11-1/4º Bends 7 Tees

More information

Marman Standard Tube Size and Variable Diameter V-Band Couplings. Simplified Stock Long Life Vibration Proof Numerous Sizes Corrosion Resistant

Marman Standard Tube Size and Variable Diameter V-Band Couplings. Simplified Stock Long Life Vibration Proof Numerous Sizes Corrosion Resistant Marman Standard Tube Size and Variable Diameter V-Band Couplings Simplified Stock Long Life Vibration Proof Numerous Sizes Corrosion Resistant V-Band Couplings Standard Tube Size and Variable Diameter

More information

ASME B31.3 Process Piping

ASME B31.3 Process Piping ASME B31.3 Process Piping Charles Becht IV, PhD, PE Don Frikken, PE Instructors BECHT ENGINEERING COMPANY, INC. Pressure Design of Metals - 1 Piping Development Process 1. Establish applicable system standard(s)

More information

PWGSC Ontario STEAM AND CONDENSATE Section Region Project HEATING PIPING Page 1 Number R

PWGSC Ontario STEAM AND CONDENSATE Section Region Project HEATING PIPING Page 1 Number R Region Project HEATING PIPING Page 1 PART 1 - GENERAL 1.1 SECTION.1 Materials and installation of steel piping INCLUDES valves, fittings for steam and condensate building services piping. 1.2 RELATED.1

More information

MUELLER CORPORATION VALVES

MUELLER CORPORATION VALVES MUELLER CORPORATION VALVES 5. Machine inserted corporation stops were developed by Hieronymus Mueller in conjunction with his development of the drilling and tapping machine used to make pressure taps

More information

Ammonia piping should conform to ASME Standard B31.5, Refrigerant Piping and IIAR Standard 2, which states the following:

Ammonia piping should conform to ASME Standard B31.5, Refrigerant Piping and IIAR Standard 2, which states the following: Refrigerant Piping The following recommendations are given for ammonia piping. Local codes or ordinances governing ammonia mains should also be followed, in addition to the recommendations here. Recommended

More information

Mueller. Pipe Repair Products. Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source.

Mueller. Pipe Repair Products. Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source. Mueller Pipe Repair Products Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source. SERVICE SADDLES Mueller service saddles, available in bronze,

More information

D I S T R I B U T E D V A L V E S TBV. Series 2100 Cryogenic Ball Valve TBV

D I S T R I B U T E D V A L V E S TBV. Series 2100 Cryogenic Ball Valve TBV TBV Series 2100 Cryogenic Ball Valve SERIES 2100 CRYOGENIC BALL VALVE The TBV 2100 Series Cryogenic Valve is designed and engineered by a staff that is experienced in cryogenic applications. It utilizes

More information

The purchaser shall specify whether the PN class or the ANSI class shall be used for the specification of the required pressure class.

The purchaser shall specify whether the PN class or the ANSI class shall be used for the specification of the required pressure class. API Specification 6DSS First Edition, June 2007 Refer to pages 20 58 of API Spec 6DSS natural gas industries Pipeline transportation systems subsea pipeline valves Annexes A, B, C and D API Monogram Required

More information

SPECIFICATIONS FOR STEEL PIPE

SPECIFICATIONS FOR STEEL PIPE SPECIFICATIONS FOR STEEL PIPE Published pipe standards serve three functions. 1. They dictate manufacturing and testing requirements and prescribed methods of measuring the required mechanical and physical

More information

MET-PRO DEAN PUMP SERIES RA P A K D A T A. Global Pump Solutions. Fan Cooled Hot Oil Pumps. Section RA

MET-PRO DEAN PUMP SERIES RA P A K D A T A. Global Pump Solutions. Fan Cooled Hot Oil Pumps. Section RA A Met-Pro Fluid Handling Technologies Business Combining the Resources of Dean Pump, Fybroc & Sethco DEAN PUMP SERIES RA Fan Cooled Hot Oil Pumps D A T A P A K Section RA SERIES RA FAN COOLED HOT OIL PUMPS

More information

61W - Wafer style resilient seated butterfly valve 61L - Lugged style resilient seated butterfly valve

61W - Wafer style resilient seated butterfly valve 61L - Lugged style resilient seated butterfly valve 61W - Wafer style resilient seated butterfly valve 61L - Lugged style resilient seated butterfly valve Features Rounded polished disc edge gives full concentric sealing, lower torques, longer seat life

More information

5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector galvznized steel bolt w/ washers and nut. Anchor 3" sq. 7 Ga.

5/16 Flange nut. Bolt Keeper Plate (8 Sq. SYS.) (3) 1/2 x 3 Hex head connector galvznized steel bolt w/ washers and nut. Anchor 3 sq. 7 Ga. 2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector galvznized

More information

twin ferrule tube fittings single ferrule tube fittings tubing data charts

twin ferrule tube fittings single ferrule tube fittings tubing data charts twin ferrule tube fittings single ferrule tube fittings tubing data charts copper annealed seamless tubing astm b-75 or equivalent ALLOWABLE STRESS = 6,000 PSI between -20 F and 100 F 1/8 3,198 3,690 4,056

More information

U.L. Listed Beverage Regulators Cylinder Gas Pressure (CO 2 ) Regulators for Soft Drink and Beer dispensing systems.

U.L. Listed Beverage Regulators Cylinder Gas Pressure (CO 2 ) Regulators for Soft Drink and Beer dispensing systems. Section 12 U.L. Listed Beverage Regulators Cylinder Gas Pressure (CO 2 ) Regulators for Soft Drink and Beer dispensing systems. R84 Regulator and C84 Regulator Configurations for Soft Drink Carbonator

More information

DIMENSIONAL BOLTING CATALOG

DIMENSIONAL BOLTING CATALOG DIMENSIONAL BOLTING CATALOG DIMENSIONAL CATALOG Table of Contents Page Screws Round Head Screws 1-1 Various Head Styles Machine Scerws 1-2 to 1-23 Tapping Screws (Approx. Hole Sizes) 1-24 Thumb and Wing

More information

January 29, 2015 L-1 STEEL PIPE

January 29, 2015 L-1 STEEL PIPE January 29, 2015 L-1 STEEL PIPE STANDARD GALVANIZED PIPE THREADED & COUPLED Lbs Pieces Average External Internal Per Per Feet Per SSC No. Size Lgth Diameter Diameter Foot Bundle Bundle Price Each Price

More information

VT Series Vertical Turbine Pumps

VT Series Vertical Turbine Pumps Water Circulation Pumps & Circulators VT Series Vertical Turbine Pumps VT Series Pumps provide the ultimate in reliability and ease of installation. Applications include condenser water, chilled water,

More information

IBV Series C, Z, C-LF2 Inverted Bucket Vertical Steam Trap

IBV Series C, Z, C-LF2 Inverted Bucket Vertical Steam Trap IBV Series C, Z, C-LF2 Inverted Bucket Vertical Steam Trap Description The IBV series inverted bucket steam trap is manufactured in three different body and cover materials. C Series (carbon steel), Z

More information

Stainless Steel Pipe & Tubing

Stainless Steel Pipe & Tubing CORPORATE OFFICE TEL (800) 766-0076 LOCAL (323) 890-4455 FAX (323) 890-4456 WWW.SMITHCOOPER.COM Stainless Steel Pipe & Tubing Stainless Pipe 304/304L & 316/316L Stainless Steel Pipe Wall Thickness and

More information

SPECIFICATIONS FOR STEEL PIPE

SPECIFICATIONS FOR STEEL PIPE SPECIFICATIONS FOR STEEL PIPE Published pipe standards serve three functions. 1. They dictate manufacturing and testing requirements and prescribed methods of measuring the required mechanical and physical

More information

Vogt Valves The Connection Bulletin for Forged Steel Flow Control Valves CB 15

Vogt Valves The Connection Bulletin for Forged Steel Flow Control Valves CB 15 The Connection Bulletin for Forged Steel Flow Control Valves CB 15 Flow Control Division Forged Steel Flow Control Valves GRADUATED DIAL AND INDICATOR FULLY GUIDED V-PORT THROTTLING DISC AND INTEGRAL HARD

More information

Belleville Spring Washer Series

Belleville Spring Washer Series Belleville Spring Washer Series High Load in Small Spaces VARIOUS CONFIGURATIONS OF BELLEVILLE WASHERS Single ONE WASHER Parallel ALL WASHERS STACKED THE SAME WAY Series ALL WASHERS STACKED OPPOSITE EACH

More information

WATER DISTRIBUTION PRODUCTS PVC WATER FITTINGS

WATER DISTRIBUTION PRODUCTS PVC WATER FITTINGS WATER DISTRIBUTION PRODUCTS PVC WATER FITTINGS CONTINENTAL INDUSTRIES ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and is today

More information

TOOL POSTS WITH TOOL HOLDERS MACHINE SHOP USE

TOOL POSTS WITH TOOL HOLDERS MACHINE SHOP USE PDF processed with CutePDF evaluation edition www.cutepdf.com TOOL POSTS WITH TOOL HOLDERS MACHINE SHOP USE Tool Post Tool Holder Tool Post Wedge Tool Post Ring FRONT Tool Post Tool Holder Tool Post Wedge

More information

DARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES

DARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES SECTION 15062 STEAM AND CONDENSATE PIPING PART 1 DESIGN DIRECTIVES 1.1 QUALITY ASSURANCE A. Comply with the provisions of the following: 1.2 DESIGN CRITERIA 1. ASME B 31.9 Building Services Piping : for

More information

ASTM A860/A860M-09 Standard Specification for Wrought High Strength. Ferritic Steel Butt Welding Fittings. 1. Scope :- 2. Reference Documents :-

ASTM A860/A860M-09 Standard Specification for Wrought High Strength. Ferritic Steel Butt Welding Fittings. 1. Scope :- 2. Reference Documents :- Standard Specification for Wrought High Strength Ferritic Steel Butt Welding Fittings 1. Scope :- 1.1 This specification covers wrought high strength ferritic steel butt-welding fitting of seamless and

More information

PRIMARY VALVE STANDARDS

PRIMARY VALVE STANDARDS PRIMARY VALVE STANDARDS MAJOR VALVE STANDARDS PETROCHEMICAL AND REFINING INDUSTRY API 600 Steel Valves Flanged & Buttwelding Ends API 600 is the main steel gate valve specification. Valve design and construction

More information

Fabricated Products ASME Code

Fabricated Products ASME Code Fabricated Products ASME Code NVE ASME Code Products meet the requirements of the ASME Boiler and Pressure Vessel Code. Our ASME Code products are produced in accordance with the requirements of the ASME

More information

Robert-James Sales, Inc. ASME B16.47 Ser. A, Ser. B INDUSTRY STANDARD and AWWA Flanges

Robert-James Sales, Inc. ASME B16.47 Ser. A, Ser. B INDUSTRY STANDARD and AWWA Flanges obert-james Sales, Inc. SME 16.47 Ser., Ser. INDUST STNDD and WW Flanges Weld, Slip-n, lind. lass 150 to lass 900 The following section is in order by pressure class due to the overlapping dimensions of

More information

Worldwide Contacts.

Worldwide Contacts. Worldwide Contacts www.tyco-fire.com Resilient-Seated Gate Valves Outside Screw and Yoke General Description TYCO Resilient-Seated Gate Valves are used in Fire Protection Systems for on/off operation.

More information

Rules for the Installation, Inspection & Testing of Air Reservoirs (Other than on Locomotives) December 1994 (TC O-0-10)

Rules for the Installation, Inspection & Testing of Air Reservoirs (Other than on Locomotives) December 1994 (TC O-0-10) Rules for the Installation, Inspection & Testing of Air Reservoirs (Other than on Locomotives) December 1994 (TC O-0-10) PART I - GENERAL 1. Short Title 2. Scope 3. Definitions 4. General 5. Reservoir

More information

Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges 1

Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges 1 Designation: F 1545 97 e1 An American National Standard Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges 1 This standard is issued under the fixed designation F 1545;

More information

Pipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).

Pipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant). Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)

More information

SECTION STEAM AND STEAM CONDENSATE PIPING AND VALVES. B. ANSI/ASME B Malleable Iron Threaded Fittings Class 150 and 300.

SECTION STEAM AND STEAM CONDENSATE PIPING AND VALVES. B. ANSI/ASME B Malleable Iron Threaded Fittings Class 150 and 300. SECTION 15520 STEAM AND STEAM CONDENSATE PIPING AND VALVES PART 1 - GENERAL 1.1 DESCRIPTION OF WORK A. Pipe and pipe fittings. B. Valves. 1.2 REFERENCES A. ANSI/ASME SEC IX - Welding and Brazing Qualifications.

More information

SPECIFICATION. Specification for Piping Design / Materials

SPECIFICATION. Specification for Piping Design / Materials Sheet 1 of 20 APPROVALS DATE REV DCN NO. BY CHECK DCC DATE AUTHOR: 3/2/11 V1 For Installation CHECKED: APPROVED: DCC RELEASE TABLE OF CONTENTS 1.0 SCOPE 2.0 CODES AND STANDARDS 3.0 MATERIAL/MANUFACTURING

More information

Yale and SENTRY Closures

Yale and SENTRY Closures Yale and SENTRY Closures Yale and SENTRY Closures Table of Contents Yale Quick Opening Closures Yale Figure 500, 500R and 515....................................3 Design Features and Safety Protection..............................4

More information

3.1 MUELLER LARGE DRILLING MACHINES

3.1 MUELLER LARGE DRILLING MACHINES MUELLER LARGE DRILLING MACHINES 3.1 Shaded area indicates change Rev. 1-09 Large Drilling Machines are used for making 2" to 24" lateral connections on water mains under pressure. These machines are available

More information

Type 92S Pilot-Operated Steam Regulator

Type 92S Pilot-Operated Steam Regulator Type 92S Pilot-Operated Steam Regulator Introduction The Type 92S steam regulator is piston actuated for high cycle steam service which includes a Type 6492L, 6492H or pilot (see Figure 1). These pilots

More information

NEWCO. Forged Steel Valves. Technical Data TC9308-4

NEWCO. Forged Steel Valves. Technical Data TC9308-4 NEWCO Forged Steel Valves Technical Data All the information contained in this manual is the exclusive property of Cameron. Any reproduction or use of the calculations, drawings, photographs, procedures

More information

CONNECTION BULLETIN. Vogt Valves. Experience In Motion. Forged Steel Flow Control Valves. FCD VVABR /05 (Replaces CB-15)

CONNECTION BULLETIN. Vogt Valves. Experience In Motion. Forged Steel Flow Control Valves. FCD VVABR /05 (Replaces CB-15) CONNECTION BULLETIN ogt alves Forged Steel Flow Control alves FCD ABR1015-00 01/05 (Replaces CB-15) Experience In Motion ogt alves Forged Steel Flow Control alves FCD ABR1015-00 01/05 Forged Steel Flow

More information

ASME B16.34 Valves Flanged, Threaded, and Welding End Published Interpretations

ASME B16.34 Valves Flanged, Threaded, and Welding End Published Interpretations ASME B16.34 Valves Flanged, Threaded, and Welding End Published Interpretations Interpretation: 10-1 B16.34-2009 Inquiry, Para 6.1 Date Issued: March 23, 2010 Record: 10-166 Question (1): According to

More information

T H E A N S W E R I S A L W A Y S

T H E A N S W E R I S A L W A Y S CONTENTS MANUFACTURING UNITS 2 INTRODUCTION GASKET IDENTIFICATION 4 AVAILABLE GASKET MATERIALS GASKET SELECTION 6 DIMENSIONAL DATA - STYLE CG & CGI TO ASME B6.20 TO SUIT ASME B6. FLANGES - IMPERIAL SIZES

More information