Direct solenoid and solenoid pilot operated valves

Transcription

1 Direct solenoid and solenoid pilot operated valves Individual mounting Series inline Manifold mounting 5 stacking sub-base non plug-in 100 Manual operator 00 Sealed solenoid enclosure Armature Solenoid push pin 45 Spring biased moveable pole piece CYL 1 N.C. 700 Poppet N.O. 900 Valve spring 8 SERIES FEATURES The patented MACSOLENOID with its non-burn out feature on AC service. Six valve functions with one individual valve. Individual, stacking body & add-a-unit manifold base capability. Use on lube or non-lube service. Extremely rapid response and cycle rate. Various types of manual operators and electrical enclosures. Extremely long service life. Optional low wattage DC solenoids down to 1 watt ISO 1 ISO ISO MAC 15A MAC 50A MAC 500A

2 100% 100% WARRANTY 18 OF PRODUCTION TESTED 100% MONTHS APPLICATION CONVERSION PROCEDURE: INDIVIDUAL MODELS The balanced poppet design facilitates using the same valve for 6 functions with any port being connected to vacuum, pressure or plugged. Piping is shown in the chart below. STACKING BODY MODELS The interchangeable function plate between the valve bodies permits selection of either -way Normally Closed or -way Normally Open operation. MANIFOLD BASE MODELS The interchangeable function plate between the valve bodies and base permits selection for - or -way, Normally Closed or Normally Open operation. On -way applications, one function plate is used for both N.C. and N.O. When "-NC" is visible on the plate, the function will be N.C. When "-NO" is visible, the function is N.O. On -way applications, two separate plates are used-one for N.C., marked "-NC"; the other for N.O., marked "-NO". The -way plates block the exhaust at the valve, permitting the mixing in a stack of -ways and -ways. Changes within a stack from one function to another can be made without disturbing the plumbing. N.C. ONLY MODELS A single purpose Normally Closed Only model is available for those applications where a greater tolerance for heavy concentrations of water, compressor products and other air line contaminants is desired. PIPING CHART FOR INDIVIDUAL MODELS Way Normally Closed X PLUGGED Way Normally Closed Selector 1 1 X P L U G G E D 1 Way Normally Open Way Normally Open Divertor Supply Operator De-Energized Operator Energized 4

3 Direct solenoid and solenoid pilot operated valves Function Port size Flow (Max) Individual mounting Series / NO-NC, / NO-NC 1/8-1/ C v inline OPERATIONAL BENEFITS 1. Balanced poppet, immune to variations of pressure.. Short stroke with high flow.. The patented solenoid develops high shifting forces. 4. Powerful return spring. 5. Manual operator standard on all valves. 6. Burn-out proof solenoid on AC service HOW TO ORDER Port size Universal valve NC only valve /8 NPTF 1/4 NPTF 1 111B-XXYZZ 11B-XXYZZ 1 161B-XXYZZ 16B-XXYZZ 45 SOLENOID OPERATOR XX Y ZZ * XX Voltage Y Manual operator ZZ Electrical connection 11 10/60, 110/50 1 Non-locking JB Rectangular connector 1 40/60, 0/50 Locking JD Rectangular connector with light 4/60, 4/50 JA Square connector 59 4 VDC (.5 W) JC Square connector with light 87 4 VDC (17.1 W) BA Flying leads (18 ) 61 4 VDC (8.5 W) CA Conduit 1/ NPS * Other options available, see page 57. Notes: CHANGING FROM NORMALLY CLOSED TO NORMALLY OPEN Individual inline valves can be changed from normally closed to normally open by connecting the inlet to port instead of port 1. NORMALLY CLOSED ONLY MODELS A single purpose Normally Closed only model is available for those applications where a greater tolerance for heavy concentrations of water, compressor products and other air line contaminants is desired. Model numbers are indicated above ISO 1 ISO ISO MAC 15A MAC 50A MAC 500A

4 100% 100% WARRANTY 18 O F P R O D U C T I O N T E S T E D 100% M O N T H S technical data Fluid : Pressure range : Lubrication : Filtration : Temperature range : Flow (at 6 bar, P=1bar) : Leak rate : Coil : Voltage range : Protection : Power : Response times : Compressed air, vacuum, inert gases Vacuum to 150 PSI Not required, if used select a medium aniline point lubricant (between 180 F and 10 F) 40 µ 0 F to 140 F (-18 C to 60 C) 0.18 C v General purpose class A, continuous duty, encapsulated -15% to +10% of nominal voltage Consult factory Inrush : 14.8 VA Holding : 10.9 VA = 1 to 17 W 4 VDC (8.5 W ) Energize : 7 ms De-energize : ms 10/60 Energize : -8 ms De-energize : -7 ms Spare parts : Options : Solenoid operator (power 4 W) : D1-XXAA, cover mounting screws 184 and seal 164. BSPP threads. dimensions Dimensions shown are metric (mm) 89,0 4,6 7,4 Ø 5 mm 56,0 16,8 # #1 17,8 ~48 F G # C D 4,1 1 H 4,9 ø 18 B 1, A Ø 4,4 mm,,0 PORT SIZE A B C D E F G H 1/ /

5 Direct solenoid and solenoid pilot operated valves Function Port size Flow (Max) Manifold mounting Series / NO-NC, / NO-NC 1/8-1/ C v stacking OPERATIONAL BENEFITS 1. Balanced poppet, immune to variations of pressure.. Short stroke with high flow.. The patented solenoid develops high shifting forces. 4. Powerful return spring. 5. Manual operator standard on all valves. 6. Burn-out proof solenoid on AC service HOW TO ORDER Port size Universal valve NC only valve /8 NPTF 1/4 NPTF SOLENOID OPERATOR 1 181B-XXYZZ 18B-XXYZZ XX Y ZZ * 1 184B-XXYZZ 185B-XXYZZ 45 XX Voltage Y Manual operator ZZ Electrical connection 11 10/60, 110/50 1 Non-locking JB Rectangular connector 1 40/60, 0/50 Locking JD Rectangular connector with light 4/60, 4/50 BA Flying leads (18 ) 59 4 VDC (.5 W) MB Common conduit 1 NPS 87 4 VDC (17.1 W) 61 4 VDC (8.5 W) * Other options available, see page 57. End plate kit required (Port size 1/4 ) : M MB option also requires end plate kit: M Notes: CHANGING FROM NORMALLY CLOSED TO NORMALLY OPEN In the case of stacking valves a reversible plate, complete with indicator, is placed between each valve body assembly. This determines whether the valve is N.C. or N.O. NORMALLY CLOSED ONLY MODELS A single purpose Normally Closed only model is available for those applications where a greater tolerance for heavy concentrations of water, compressor products and other air line contaminants is desired. Model numbers are indicated above ISO 1 ISO ISO MAC 15A MAC 50A MAC 500A

6 100% 100% WARRANTY 18 O F P R O D U C T I O N T E S T E D 100% M O N T H S technical data Fluid : Pressure range : Lubrication : Filtration : Temperature range : Flow (at 6 bar, P=1bar) : Leak rate : Coil : Voltage range : Protection : Power : Response times : Compressed air, vacuum, inert gases Vacuum to 150 PSI Not required, if used select a medium aniline point lubricant (between 180 F and 10 F) 40 µ 0 F to 140 F (-18 C to 60 C) 0.18 C v 100 cm /min General purpose class A, continuous duty, encapsulated -15% to +10% of nominal voltage Consult factory Inrush 14.8 VA Holding : 10.9 VA DC : 1 to 17.1 W 4 VDC (8.5 W) Energize : 7 ms De-energize : ms 10/60 Energize : -8 ms De-energize : -7 ms Spare parts : Options : Solenoid operator (power 4 W) : D1-XXAA, cover mounting screws 506 and seal 164. Function plate : N Tie-rod (x) : Inlet isolator plate : N0100. Exhaust isolator plate : N BSPP threads. Bottom inlet (Mod. 010). dimensions Dimensions shown are metric (mm) 1/4 INLET & EXHAUST PORTS EACH END CYL. PORT 1/8 OR 1/4 MT G SLOT Ø 6,6 mm 1/8 - OPTIONAL BOTTOM INLET PORTS 8

7 Direct solenoid and solenoid pilot operated valves Function Port size Flow (Max) Manifold mounting Series / NO-NC, / NO-NC 1/ C v sub-base non plug-in OPERATIONAL BENEFITS 1. Balanced poppet, immune to variations of pressure.. Short stroke with high flow.. The patented solenoid develops high shifting forces. 4. Powerful return spring. 5. Manual operator standard on all valves. 6. Burn-out proof solenoid on AC service HOW TO ORDER Port size Universal valve NC only valve Valve less base 1/8 base NPTF 1 10B-XXYZZ 1B-XXYZZ 1 170B-XXYZZ 17B-XXYZZ 45 SOLENOID OPERATOR XX Y ZZ * XX Voltage 11 10/60, 110/ /60, 0/50 4/60, 4/ VDC (.5 W) 87 4 VDC (17.1 W) 61 4 VDC (8.5 W) * Other options available, see page 57. Y Manual operator 1 Non-locking Locking ZZ Electrical connection JB Rectangular connector JD Rectangular connector with light BA Flying leads (18 ) MA Common conduit 1 NPS RA Conduit /8 NPS End plate kit required (Port size : 1/4 ) : A MA option also requires end plate kit : M OPTIONS 1XB-XXYZZ 14XB-XXYZZ 10 -way N.C. -way N.O. (Base only) Notes: CHANGING FROM NORMALLY CLOSED TO NORMALLY OPEN For manifold base mounted valves a plate is provided between the valve and the base. Three plates are available; a reversible plate for Way valves (N.C. & N.O.), one plate for Way N.C. and one for Way N.O. Appropriate plates, determined by the valve model number, are supplied automatically with the valve. NORMALLY CLOSED ONLY MODELS A single purpose Normally Closed only model is available for those applications where a greater tolerance for heavy concentrations of water, compressor products and other air line contaminants is desired. Model numbers are indicated above ISO 1 ISO ISO MAC 15A MAC 50A MAC 500A

8 100% 100% WARRANTY 18 O F P R O D U C T I O N T E S T E D 100% M O N T H S technical data Fluid : Pressure range : Lubrication : Filtration : Temperature range : Flow (at 6 bar, P=1bar) : Leak rate : Coil : Voltage range : Protection : Power : Response times : Compressed air, vacuum, inert gases Vacuum to 150 PSI Not required, if used select a medium aniline point lubricant (between 180 F and 10 F) 40 µ 0 F to 140 F (-18 C to 60 C) 0.14 C v General purpose class A, continuous duty, encapsulated -15% to +10% of nominal voltage Consult factory Inrush : 14.8 VA Holding : 10.9 VA = 1 to 17 W 4 VDC (8.5 W) Energize : 7 ms De-energize : ms 10/60 Energize : -8 ms De-energize : -7 ms Spare parts : Options : Note : Solenoid operator (power 4 W) : D1-XXAA, cover mounting screws 184 and seal 164. Function plate : A Seal between manifold bases : 166. Tie-rod (x) : BSPP threads. Isolation of inlet : Mod. 1P. Isolation of exhaust : Mod. 1E. Additional bottom inlet : Mod Bottom cyl. port : Mod All bottom & side ports : Mod Specify mod. number after valve model number (i.e. 1B-111BA Mod. 010) dimensions 1/8 CYL. PORT Dimensions shown are metric (mm) OPTIONAL 1/8 BOTTOM PORTS 1/4 INLET & EXHAUST PORTS EACH END MT G SLOT Ø 6,6 mm 0

9 I n t r i n s i c a l l y S a f e V a l v e s HOW TO ORDER BODY OPTIONS SERIES 1 X X B - (XXYZZ) - FM - SOLENOID OPTIONS REVISION LEVEL SEE BELOW VALVE FUNCTION 6 N.C. only ind. inline 7 N.C. only manifold 8 Stacking body PORT SIZE/BODY STYLE 0 Manifold valve less base 1 1/8" NPTF ind.inline 1/8" NPTF manifold 1/4" NPTF ind.inline 4 1/8" NPTF stacking, -way N.C. only 5 1/4" NPTF stacking, -way N.C. only 6 1/8" BSPP inline 7 1/4" BSPP inline 8 1/8" BSPP stacking, -way N.C. only 9 1/4" BSPP stacking, -way N.C. only SOLENOID OPTIONS EXAMPLE : XX Y ZZ - FM XX DC VOLTAGE Y MANUAL OPERATOR ZZ ENCLOSURE A5 1 VDC (0.6 W) A6 4 VDC (0.6 W) 0 No operator 1 Non-locking Recessed (std.) Locking Recessed Non-locking Extended 4 Locking Extended AA BA CA CC JB JM NA RA MA MB JIC w/1/" NPS Conduit Grommet Conduit 1/" NPS Conduit 1/" NPT (CSA threads) Rectangular Plug-in Rectangular Male only Conduit 1/" NPS w/ground wire Conduit /8" NPS for Manifold models Com. Conduit 1" NPS (Manifold models) Com. Conduit 1" NPS (Stacking models) (MA & MB common conduit covers require 1#M conduit end plate kit per stack) 100 SERIES-SUPPLEMENTAL TECHNICAL DATA STACKING BODY ACCESSORIES : STACKING END PLATE KIT- MOD. NO. DESCRIPTION MODEL AVAILABILITY 0004 All bottom and side ports Manifold models only 0009 Bottom and side cylinder ports with Manifold models only side only inlet and exhaust ports 010 Additionnal bottom inlet Manifold & stacking models 1P For isolating the common inlet Manifold models only passage between manifold bases 1E For isolating the common exhaust Manifold models only passage between manifold bases TO ORDER Add the appropriate modification number from the table above after the valve number, EXAMPLE : 17B-A51BA-FM MOD For each gang one kit is required. TO ORDER- Specify number M (1/4" NPTF) or M P (1/4" BSPP). INLET ISOLATOR PLATE N-0100 EXHAUST ISOLATOR PLATE N MANIFOLD ACCESSORIES : MANIFOLD END PLATE KIT- For each gang one kit is required. TO ORDER- Specify number A (1/4" NPTF) or A P (1/4" BSPP). 4

10 O p t i o n s O P T I O N S Codification table for voltages / Manual operator / Electrical connection / Wire length VALVE CODE - XX Y ZZ (-VV) 1 4 OPTIONS AVAILABLE FOR OPTIONS AVAILABLE FOR - valves type 100 Series - pilot valves "CNOMO" - valves type 00 Series - Pilot operated valves with pilots type 100 Series Series : ISO 1 - ISO - ISO. - MAC 15 - MAC 50 - MAC pilot operated valves with pilots type 00 Series Series : Pilot operated valves with pilots "CNOMO" Series : ISO1 - ISO - ISO 57

11 O P T I O N S Used on valve series: 100, 55, 56, 700, 800, 900, 600, 6500, 6600, 100, MVA1C, MVAB, MVAB, MAC15, MAC50, MAC XX Y ZZ VOLTAGE 1. VOLTAGE (100 Serie type coil) 11 10/60, 110/ /60, 0/ /60, 100/ /60, 00 / /60 0 6/60 1 1/50, 1/60 4/60, 4/50 /60, / /60, 4/50 6* 80/50, 440/50, 440/60, 480/60 9 0/ /50, 10/ / /60 B1 4/ VDC (6 W) 51 4 VDC (4 W) 54 1 VDC (4 W) 55 1 VDC (6 W) 57 1 VDC (.5 W) 59 4 VDC (.5 W) 60 1 VDC (8.5 W) 61 4 VDC (8.5 W) 64 6 VDC (6 W) 65 VDC (7 W) VDC (5.8 W) VDC (7.5 W) VDC (6.4 W) 69* 0 VDC (8.7 W), 50 VDC (11. W) VDC (8.8 W) 76* 100 VDC (6.9 W) 84* 15 VDC (10.9 W) 87* 4 VDC (17.1 W) 88* 1 VDC (17.4 W) 89* 6 VDC (18.8 W) 90 8 VDC (8. W) 91* 6 VDC (10.6 W) VDC (6.5 W) 94 VDC (7 W) 95 8 VDC (6.4 W) A1 4 VDC (1 W) A 1 VDC (1 W) A 9 VDC (1 W) MOD. DD01 : Protection diode (DC) - MAX. 8.5W MOD. MOV1 : Protection varistor (AC) - MAX. 8.5W * Voltages are CLSF only Used on valve series: 00, 57, 58, VOLTAGE (00 Serie type coil) - XX Y ZZ VOLTAGE 11 10/60, 110/50, 4 VDC (6 W) 1 40/60, 0/ /60, 100/ /60, 00/50 0 6/60 1 1/60 4/60, 4/50 /60, / /60, 4/ / /60, 440/ / /50 9 0/ / /60, 550/50 10/60, 110/50 600/ / / VDC (6 W) 51 4 VDC (4.5 W) 5 4 VDC (.5 W) 5 4 VDC (1.0 W) 55 1 VDC (6 W) 57 1 VDC (.5 W) VDC (.5 W) 60 1 VDC (9.5 W) 61 4 VDC (8.5 W) 64 6 VDC (8.5 W) 65 VDC (10 W) VDC (11.5 W) VDC (10.5 W) VDC (1. W) VDC (9. W) 71 8 VDC (8. W) 7 4 VDC (1 W) VDC (10 W) 74 7 VDC (11. W) VDC (11. W) VDC (9 W) 77 0 VDC (10 W), 0 VDC (11.6 W) 78* 4 VDC (4 W) VDC (10.6 W) VDC (11.1 W) 8 15 VDC (8.1 W) VDC (10 W) 86 6 VDC (11 W) 9* 1 VDC (4 W) 58

12 O p t i o n s O P T I O N S. MANUAL OPERATOR (Common options for 100 & 00 Series type coils) - XX Y ZZ MANUAL OPERATOR 0 No operator 5* No Operator with Light 1 Non-locking recessed 6* Non-Locking Recessed with Light Locking recessed 7* Locking Recessed with Light Non-locking extended 8* Non-Locking Extended with Light 4 Locking extended 9* Locking Extended with Light * Lights used with AA electrical connection. ELECTRICAL CONNECTION (100 Serie type coil) - XX Y ZZ ELECTRICAL CONNECTION AA Wiring box with 1/" NPS conduit BA Flying leads CA 1/" NPS conduit CC 1/" NPT conduit FA Military type PIN GA Military type PIN HA AA with ground wire JA* Square connector JB Rectangular connector JC* Square connector with light JD Rectangular connector with light JE Square connector on top (ISO, ISO) JF Rectangular connector on top (ISO1, ISO, ISO) JG JE with light JH JF with light JJ Square connector, male only JM Rectangular connector, male only MA Electrical common conduit (100 Series-Manifold/900 Series) MB Electrical common conduit (100 Series-Stacking/700 Series) NA CA with ground wire NC CC with ground wire RA /8" NPS conduit * Not to be used with 100, 800 and 900 Series manifold mounting. ELECTRICAL CONNECTION (00 Serie type coil) - XX Y ZZ ELECTRICAL CONNECTION AA Wiring box with 1/" NPS conduit BA Flying leads CA 1/" NPS conduit CC 1/" NPT conduit EA Explosion proof (00 Series) EA Explosion proof (57, 58 & 59 Series) FA Military type PIN GA Military type PIN HA AA with ground wire JA* Square connector JC Square connector with light JJ Square connector, male only NA CA with ground wire NC CC with ground wire 59

13 O P T I O N S 4. COIL WIRE LENGTH (Common options for 100 & 00 Serie type coils) - XX Y ZZ (-VV) WIRE LENGTH AA 18 AB 4 AD 6 AE 48 AF 7 AG 6 AR 1 AU 10 BA 60 BB 144 Series 6000 : wire length, from the base MOD L04 4 MOD L06 6 MOD L MOD L MOD L07 7 MOD L